Allen-Bradley POINT I/O 1734-IB4 Installation Instructions Manual

Marque: Allen-Bradley

Modèle: POINT I/O 1734-IB4

Taper: Installation Instructions Manual

Ce manuel convient également à

POINT I/O is a trademark of Rockwell Automation1

DeviceNet is a trademark of ODVA, Inc. Publication 1734-IN051D-EN-P - April 2004

Installation Instructions

POINT I/O Input Module

(Cat. No. 1734-IB2, -IB4 and -IB8, Series C)

Description Description

Mounting Base

6 RTB Removal Handle

2 Mechanical Keying (orange) 7

Removable Terminal Block (RTB)

3 Module Wiring Diagram 8 DIN Rail Locking Screw (orange)

4 Module Locking Mechanism 9 Slide-in Writable Label

5 Insertable I/O Module 10 Interlocking Side Pieces

Wiring Base Assembly consists of item 1) mounting base, 1734-MB and item 7) removable

terminal block, 1734-RTB or -RTBS.

Module

Status

AB Parts

2 POINT I/O Input Module

Publication 1734-IN051D-EN-P - April 2004

This Series C product can be used with DeviceNet and PROFIBUS

adapters. It can be used with ControlNet and Ethernet adapters using

RSLogix 5000, version 11 (or higher) software.

Important User Information

Solid state equipment has operational characteristics differing from those of

electromechanical equipment. Safety Guidelines for the Application, Installation and

Maintenance of Solid State Controls (Publication SGI-1.1 available from your local

Rockwell Automation sales office or online at http://www.ab.com/manuals/gi)

describes some important differences between solid state equipment and hard-wired

electromechanical devices. Because of this difference, and also because of the wide

variety of uses for solid state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this equipment

is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or

consequential damages resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative

purposes. Because of the many variables and requirements associated with any

particular installation, Rockwell Automation, Inc. cannot assume responsibility or

liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of

information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written

permission of Rockwell Automation, Inc. is prohibited.

Throughout this manual we use notes to make you aware of safety considerations.

POINT I/O Input Module 3

Publication 1734-IN051D-EN-P - April 2004

WARNING

Identifies information about practices or circumstances that

can cause an explosion in a hazardous environment, which

may lead to personal injury or death, property damage, or

economic loss.

ATTENTION

Identifies information about practices or circumstances that

can lead to personal injury or death, property damage, or

economic loss. Attentions help you:

• identify a hazard

• avoid a hazard

• recognize the consequence

IMPORTANT

Identifies information that is critical for successful

application and understanding of the product.

Important User Information

AB Parts

4 POINT I/O Input Module

Publication 1734-IN051D-EN-P - April 2004

ATTENTION

Environment and Enclosure

This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications

(as defined in IEC publication 60664-1), at altitudes up to 2000

meters without derating.

This equipment is considered Group 1, Class A industrial

equipment according to IEC/CISPR Publication 11. Without

appropriate precautions, there may be potential difficulties

ensuring electromagnetic compatibility in other environments

due to conducted as well as radiated disturbance.

This equipment is supplied as "open type" equipment. It must

be mounted within an enclosure that is suitably designed for

those specific environmental conditions that will be present and

appropriately designed to prevent personal injury resulting from

accessibility to live parts. The interior of the enclosure must be

accessible only by the use of a tool. Subsequent sections of this

publication may contain additional information regarding

specific enclosure type ratings that are required to comply with

certain product safety certifications.

See NEMA Standards publication 250 and IEC publication

60529, as applicable, for explanations of the degrees of

protection provided by different types of enclosure. Also, see the

appropriate sections in this publication, as well as the

Allen-Bradley publication 1770-4.1 ("Industrial Automation

Wiring and Grounding Guidelines"), for additional installation

requirements pertaining to this equipment.

POINT I/O Input Module 5

Publication 1734-IN051D-EN-P - April 2004

WARNING

EXPLOSION HAZARD

• Do not disconnect equipment unless power has been

removed or the area is known to be nonhazardous.

• Do not disconnect connections to this equipment unless

power has been removed or the area is known to be

nonhazardous. Secure any external connections that mate

to this equipment by using screws, sliding latches, threaded

connectors, or other means provided with this product.

• Substitution of components may impair suitability for Class

I, Division 2.

• If this product contains batteries, they must only be

changed in an area known to be nonhazardous.

ATTENTION

Preventing Electrostatic Discharge

This equipment is sensitive to electrostatic discharge,

which can cause internal damage and affect normal

operation. Follow these guidelines when you handle

this equipment:

• Touch a grounded object to discharge potential

static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component

boards.

• Do not touch circuit components inside the

equipment.

• If available, use a static-safe workstation.

• When not in use, store the equipment in

appropriate static-safe packaging.

AB Parts

6 POINT I/O Input Module

Publication 1734-IN051D-EN-P - April 2004

Installing the Mounting Base

To install the mounting base on the DIN rail, proceed as follows.

1. Position the mounting base vertically above the installed units

(adapter, power supply or existing module.

2. Slide the mounting base down allowing the interlocking side pieces to

engage the adjacent module or adapter.

3. Press firmly to seat the mounting base on the DIN rail. The mounting

base will snap into place.

4. To remove the mounting base from the DIN rail, remove the module,

and use a small bladed screwdriver to rotate the base locking screw to

a vertical position. This releases the locking mechanism. Then lift

straight up to remove.

Installing the I/O Module

The module can be installed before, or after base installation. Make sure that

the mounting base is correctly keyed before installing the module into the

mounting base. In addition, make sure the mounting base locking screw is

positioned horizontal referenced to the base.

ATTENTION

POINT I/O is grounded through the DIN rail to chassis

ground. Use zinc plated, yellow chromated steel DIN rail

to assure proper grounding. Using other DIN rail

materials (e.g. aluminum, plastic, etc.) which can corrode,

oxidize or are poor conductors can result in improper or

intermittent platform grounding.

WARNING

When you insert or remove the module while

backplane power is on, an electrical arc can occur. This

could cause an explosion in hazardous location

installations. Be sure that power is removed or the area

is nonhazardous before proceeding.

POINT I/O Input Module 7

Publication 1734-IN051D-EN-P - April 2004

1. Using a bladed screwdriver, rotate the keyswitch (2) on the mounting

base clockwise until the number required for the type of module being

installed aligns with the notch in the base.

2. Make certain the DIN rail locking screw is in the horizontal position.

(You cannot insert the module if the locking mechanism is unlocked.)

3. Insert the module straight down into the mounting base and press to

secure. The module will lock into place.

Installing the Removable Terminal Block (RTB)

A removable terminal block is supplied with your wiring base assembly. To

remove, pull up on the RTB handle. This allows the mounting base to be

removed and replaced as necessary without removing any of the wiring. To

reinsert the removable terminal block, proceed as follows.

1. Insert the end opposite the handle into the base unit. This end has a

curved section that engages with the wiring base.

2. Rotate the terminal block into the wiring base until it locks itself in

place.

3. If an I/O module is installed, snap the RTB handle into place on the

module.

WARNING

When you connect or disconnect the Removable

Terminal Block (RTB) with field side power applied, an

electrical arc can occur. This could cause an explosion

in hazardous location installations. Be sure that power

is removed or the area is nonhazardous before

proceeding.

AB Parts

8 POINT I/O Input Module

Publication 1734-IN051D-EN-P - April 2004

Removing a Mounting Base

To remove a mounting base, you must remove any installed module, and the

module installed in the base to the right. Remove the removable terminal

block (if wired).

1. Unlatch the RTB handle on the I/O module.

2. Pull on the RTB handle to remove the removable terminal block.

3. Press on the module lock on the top of the module.

4. Pull on the I/O module to remove from the base.

5. Repeat steps 1, 2, 3 and 4 for the module to the right.

6. Use a small bladed screwdriver to rotate the orange base locking

screw to a vertical position. This releases the locking mechanism.

7. Then lift straight up to remove.

WARNING

When you connect or disconnect the Removable

Terminal Block (RTB) with field side power applied, an

electrical arc can occur. This could cause an explosion

in hazardous location installations.

Be sure that power is removed or the area is

nonhazardous before proceeding.

WARNING

When you insert or remove the module while

backplane power is on, an electrical arc can occur. This

could cause an explosion in hazardous location

installations. Be sure that power is removed or the area

is nonhazardous before proceeding.

POINT I/O Input Module 9

Publication 1734-IN051D-EN-P - April 2004

Communicating with Your Module

I/O messages are sent to (consumed) and received from (produced) the

POINT I/O modules. These messages are mapped into the processor’s

memory. This POINT I/O input module produces 1 byte of input data

(scanner Rx). It does not consume I/O data (scanner Tx).

Default Data Map for the 1734-IB2 Input Module

Message size: 1 Byte

Default Data Map for the 1734-IB4 Input Module

Message size: 1 Byte

Default Data Map for the 1734-IB8 Input Module

Message size: 1 Byte

7 6 5 4 3 2 1 0

Produces (Rx) I1 I0

Consumes (Tx) No consumed data

Where: I0 = channel 0, I1 = channel 1; 0 = off, 1 = on

7 6 5 4 3 2 1 0

Produces (Rx) I3 I2 I1 I0

Consumes (Tx) No consumed data

Where: I0 = channel 0, I1 = channel 1, I2 = channel 2 and I3 = channel 3; 0 = off, 1 = on

7 6 5 4 3 2 1 0

Produces (Rx) I7 I6 I5 I4 I3 I2 I1 I0

Consumes (Tx) No consumed data

Where: I0 = channel 0, I1 = channel 1, I2 = channel 2 and I3 = channel 3; I4 = channel 4,

I5 = channel 5, I6 = channel 6, I7 equals channel 7; 0 = off, 1 = on

AB Parts

10 POINT I/O Input Module

Publication 1734-IN051D-EN-P - April 2004

Wiring the Input Modules

24VDC

Sink

Input

Module

Status

Network

Status

1734

IB2

NODE:

24VDC

Sink

Input

Module

Status

Network

Status

1734

IB4

NODE:

24VDC

Sink

Input

Module

Status

Network

Status

1734

IB8

NODE:

41974

Module Status

Network Status

Status of Input 0

Status of Input 1

Input 0

Input 1

Input = 0 and 1

NC = No Connection (2 and 3)

C = Common (4 and 5)

V = Supply (6 and 7)

Input 0

Input 1

Input 2 Input 3

Status of Input 2

Status of Input 3

Input = 0, 1, 2 and 3

C = Common (4 and 5)

V = Supply (6 and 7)

1734-IB2

1734-IB4 1734-IB8

Input 0

Input 1

Input 2 Input 3

Input 4 Input 5

Input 6 Input 7

Status - Input 0 & 4

Status - Input 1 & 5

Status - Input 2 & 6

Status - Input 3 & 7

Input = 0, 1, 2, 3, 4, 5, 6 and 7

Note: V and C are

daisychained from either the

Adapter, 1734-FPD,

1734-EP24DC, or from a user

supplied auxiliary terminal

POINT I/O Input Module 11

Publication 1734-IN051D-EN-P - April 2004

Wiring for 1734-IB2

Channel Input Common Voltage

0 0 4 6

1 1 5 7

Connect common on 3-wire proximity switches.

12/24V dc is supplied through the internal power bus.

Prox

In 0 In 1

Prox

V = 12/24V dc

C = Common

41966

3-wire

Sink Input

2-wire

AB Parts

12 POINT I/O Input Module

Publication 1734-IN051D-EN-P - April 2004

Wiring for 1734-IB4

Channel Input Common Voltage

0 0 4 6

1 1 5 7

2 2 4 6

3 3 5 7

Connect common on 3-wire proximity switches.

12/24V dc is supplied through the internal power bus.

Prox

In 0 In 1

In 2

In 3

Prox ProxProx

41967

V = 12/24V dc

C = Common

Sink Input

3-wire2-wire

POINT I/O Input Module 13

Publication 1734-IN051D-EN-P - April 2004

Wiring for 1734-IB8

Note: When connecting more than 1 wire in a termination point, make sure

that both wires are the same gauge and type.

Channel Input Channel Input

0 0 4 4

1 1 5 5

2 2 6 6

3 3 7 7

Daisychain common and power connections from 1734 Adapter, 1734-FPD, 1734-EP24DC

or from user supplied external auxiliary terminal block.

Prox

In 0

In 1

In 2

In 4

In 6

In 7

In 5

In 3

Prox

41967

Sink Input

3-wire

2-wire

Prox

3-wire

2-wire

3-wire

V = 12/24V dc

C = Common

AB Parts

14 POINT I/O Input Module

Publication 1734-IN051D-EN-P - April 2004

4V dc 2 Input Sink Module Cat. No. 1734-IB2

Troubleshooting with the Indicators

Indication Probable Cause

Module Status

Off No power applied to device

Green Device operating normally

Flashing Green Device needs commissioning due to configuration

missing, incomplete or incorrect.

Flashing Red Recoverable fault.

Red Unrecoverable fault may require device replacement

Flashing Red/Green Device is in self-test

Module Status

Network Status

Status of Input 0

Status of Input 1

24VDC

Sink

Input

Module

Status

Network

Status

1734

IB4

NODE:

24VDC

Sink

Input

Module

Status

Network

Status

1734

IB2

NODE:

1734-IB2

1734-IB4

1734-IB8

Status of Input 0 & 4

Status of Input 1 & 5

Status of Input 2 & 6

Status of Input 3 & 7

Module Status

Network Status

24VDC

Sink

Input

Module

Status

Network

Status

1734

IB8

NODE:

Status of Input 2

Status of Input 3

POINT I/O Input Module 15

Publication 1734-IN051D-EN-P - April 2004

Network Status

Off Device is not on-line

- Device has not completed dup_MAC_id test.

- Device not powered - check module status indicator

Flashing Green Device is on-line but has no connections in the

established state.

Green Device on-line and has connections in the established

state.

Flashing Red One or more I/O connections in timed-out state

Red Critical link failure - failed communication device.

Device detected error that prevents it communicating on

the network.

Flashing Red/Green Communication faulted device - the device has detected

a network access error and is in communication faulted

state. Device has received and accepted an Identify

Communication Faulted Request - long protocol

message.

Indication Probable Cause

I/O Status

Off Input is in the off-state

Yellow Input is in the on-state

Indication Probable Cause

AB Parts

16 POINT I/O Input Module

Publication 1734-IN051D-EN-P - April 2004

Safety Approvals

North American Hazardous Location Approval

The following modules are North American Hazardous Location approved:

1734-IB2, 1734-IB4 and 1734-IB8.

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l’utilisation de cet équipement

en environnements dangereux:

Products marked “CL I, DIV 2, GP A, B, C, D” are suitable

for use in Class I Division 2 Groups A, B, C, D, Hazardous

Locations and nonhazardous locations only. Each product

is supplied with markings on the rating nameplate

indicating the hazardous location temperature code. When

combining products within a system, the most adverse

temperature code (lowest “T” number) may be used to

help determine the overall temperature code of the

system. Combinations of equipment in your system are

subject to investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués “CL I, DIV 2, GP A, B, C, D” ne

conviennent qu’à une utilisation en environnements de Classe I

Division 2 Groupes A, B, C, D dangereux et non dangereux.

Chaque produit est livré avec des marquages sur sa plaque

d’identification qui indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs produits sont

combinés dans un système, le code de température le plus

défavorable (code de température le plus faible) peut être

utilisé pour déterminer le code de température global du

système. Les combinaisons d’équipements dans le système

sont sujettes à inspection par les autorités locales qualifiées

au moment de l’installation.

EXPLOSION HAZARD -

• Do not disconnect equipment unless

power has been removed or the area

is known to be nonhazardous.

• Do not disconnect connections to

this equipment unless power has

been removed or the area is known

to be nonhazardous. Secure any

external connections that mate to

this equipment by using screws,

sliding latches, threaded

connectors, or other means provided

with this product.

• Substitution of components may

impair suitability for Class I, Division

• If this product contains batteries,

they must only be changed in an

area known to be nonhazardous.

RISQUE D’EXPLOSION –

• Couper le courant ou s’assurer que

l’environnement est classé non

dangereux avant de débrancher

l'équipement.

• Couper le courant ou s'assurer que

l’environnement est classé non

dangereux avant de débrancher les

connecteurs. Fixer tous les

connecteurs externes reliés à cet

équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou

autres moyens fournis avec ce

produit.

• La substitution de composants peut

rendre cet équipement inadapté à une

utilisation en environnement de

Classe 1, Division 2.

• S’assurer que l’environnement est

classé non dangereux avant de

changer les piles.

WARNING

AVERTISSEMENT

POINT I/O Input Module 17

Publication 1734-IN051D-EN-P - April 2004

European Hazardous Location Approval

The following modules are European Zone 2 approved: 1734-IB2, 1734-IB4

and 1734-IB8.

European Zone 2 Certification (The following applies when the product

bears the EEx Marking)

This equipment is intended for use in potentially explosive atmospheres as defined

by European Union Directive 94/9/EC.

DEMKO certifies that this equipment has been found to comply with the Essential

Health and Safety Requirements relating to the design and construction of Category

3 equipment intended for use in potentially explosive atmospheres, given in Annex

II to this Directive. The examination and test results are recorded in

EC-type-examination certificate DEMKO 04 ATEX 0330347 X.

Compliance with the Essential Health and Safety Requirements has been assured by

compliance with EN 50021.

IMPORTANT

Observe the following additional Zone 2 certification

requirements.

• This equipment is not resistant to sunlight or other sources

of UV radiation.

• The secondary of a current transformer shall not be

open-circuited when applied in Class I, Zone 2 environments.

• Equipment of lesser Enclosure Type Rating must be installed

in an enclosure providing at least IP54 protection when

applied in Class I, Zone 2 environments.

• This equipment shall be used within its specified ratings

defined by Allen-Bradley.

• Provision shall be made to prevent the rated voltage from

being exceeded by transient disturbances of more than 40%

when applied in Class I, Zone 2 environments

Specifications - 1734-IB2, -IB4 and -IB8 Input Modules

Input Specifications (IEC 3 24V dc Input Compliant)

Inputs per Module 1734-IB2 - 2 (1 group of 2), sinking

1734-IB4 - 4 (1 group of 4), sinking

1734-IB8 - 8 (1 group of 8), sinking

ON-State Voltage 10V dc minimum

24V dc nominal

28.8V dc maximum

ON-State Current 2mA minimum

4mA nominal @ 24V dc

5mA maximum

OFF-State Voltage 5V dc maximum

AB Parts

18 POINT I/O Input Module

Publication 1734-IN051D-EN-P - April 2004

OFF-State Current 1.5mA minimum

Input Impedance 4.7KΩ maximum, 3.6KΩ nominal

Input Filter Time

OFF to ON

ON to OFF

0.5ms hardware plus 0-63ms (user selectable)

Indicators 1 green/red network status indicator, logic side

1 green/red module status indicator, logic side

1734-IB2 - 2 yellow input status indicators, logic side

1734-IB4 - 4 yellow input status indicators, logic side

1734-IB8 - 8 yellow input status indicators, logic side

Keyswitch Position 1

General Specifications

Module Location 1734-TB or -TBS wiring base assembly

Pointbus Current 75mA maximum @ 5V dc

Power Dissipation 1734-IB2 - 0.7W maximum @ 28.8V dc

1734-IB4 - 1.0W maximum @ 28.8V dc

1734-IB8 - 1.6W maximum @ 28.8V dc

Thermal Dissipation 1734-IB2 - 2.4 BTU/hr maximum @ 28.8V dc

1734-IB4 - 3.4 BTU/hr maximum @ 28.8V dc

1734-IB8 - 5.5 BTU/hr maximum @ 28.8V dc

Isolation Voltage (Minimum) Tested to withstand 2500V dc for 60s

Field Power Bus

Supply Voltage

Voltage Range

24V dc nominal

10-28.8V dc

Dimensions Inches

(Millimeters)

2.2H x 0.47W x 2.97L

(56H x 12W x 75.5L)

Environmental Conditions

Operational Temperature IEC 60068-2-1 (Test Ad, Operating Cold),

IEC 60068-2-2 (Test Bd, Operating Dry Heat),

IEC 60068-2-14 (Test Nb, Operating Thermal Shock):

-20 to 55°C (-4 to 131°F)

Storage Temperature IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating

Cold),

IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry

Heat),

IEC 60068-2-14 (Test Na, Unpackaged Nonoperating

Thermal Shock):

-40 to 85°C (-40 to 185°F)

Relative Humidity IEC 60068-2-30 (Test Db, Unpackaged Nonoperating

Damp Heat):

5 to 95% noncondensing

POINT I/O Input Module 19

Publication 1734-IN051D-EN-P - April 2004

Shock

Operating

Non-operating

IEC 60068-2-27 (Test Ea, Unpackaged Shock)

30g peak acceleration

50g peak acceleration

Vibration IEC 60068-2-6, (Test Fc, Operating)

Tested 5g @ 10-500Hz

ESD Immunity IEC 61000-4-2:

6kV contact discharges

8kV air discharges

Radiated RF Immunity IEC 61000-4-3:

10V/m with 200Hz 50% Pulse 100%AM at 1890Mhz

10V/m with 200Hz 50% Pulse 100%AM at 900Mhz

10V/m with 1kHz sine-wave 80%AM from 30MHz to

2000MHz

EFT/B Immunity IEC 61000-4-4:

±4kV at 2.5kHz on signal ports

±4kV at 2.5kHz on power ports

Surge Transient Immunity IEC 61000-4-5:

±1kV line-line(DM) and ±2kV line-earth(CM) on power

and signal ports

Conducted RF Immunity IEC 61000-4-6:

10Vrms with 1kHz sine-wave 80%AM from 150kHz to

80MHz

Emissions CISPR 11

Group 1, Class A

Enclosure Type Rating None (open-style)

Conductors Wire Size

Allen-Bradley POINT I/O 1734-IB4 Installation Instructions Manual

Marque: Allen-Bradley

Modèle: POINT I/O 1734-IB4

Taper: Installation Instructions Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Allen-Bradley POINT I/O 1734-IB4

Allen-Bradley POINT I/O 1734-IB4 Installation Instructions Manual

Ce manuel convient également à

Allen-Bradley POINT I/O 1734-IB4 Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents