Maruyama E27 Le manuel du propriétaire

Marque: Maruyama

Modèle: E27

Taper: Le manuel du propriétaire

Ce manuel convient également à

The POWER in Outdoor Power

Completely read and understand this manual PRIOR to using this product.

Lea y entienda este manual a fondo, ANTES de usar este producto.

Lisez complètement et comprenez ce manuel AVANT d'utiliser ce produit.

Power Edger

Poder Orilladora

Motorisé Coupe Bordure

E23

E27

OWNER'S/OPERATOR'S MANUAL

MANUAL DEL PROPIETARIO U OPERADOR

MANUEL DU PROPRIETAIRE/DE L'UTILISATEUR

— US-1 —

Limited Warranty Statement

All Maruyama commercial/ industrial products are warranted to the original purchaser to be free from defects

in material and workmanship from the date of purchase for the time periods listed as follows:

Lifetime for inner drive shaft on trimmers and brushcutters and all ignition modules.

3 years for residential, non-institutional, non-income producing use.

1 year for industrial, commercial, institutional, rental and income producing use.

Maruyama AE series engines and Kawasaki TEX45/TEX54 are covered exclusively for one additional

year of industrial, commercial, institutional, rental and income producing use (total of 2 years).

All other engines refer to engine manufacturer's warranty statement.

Any part of a Maruyama product found to be defective within the applicable warranty period shall, at

Maruyama's option, be repaired or replaced without charge. Warranty consideration is obtained by delivering

any Maruyama product believed to be defective to an Authorized Maruyama Servicing Dealer within the

applicable warranty period.

The purchaser shall not be charged for diagnostic labor that leads to the determination that a warranted part

is defective, if the diagnostic work is performed at a Maruyama Dealer.

Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled

only for regular inspection to the effect of "repair or replace as necessary" shall be warranted for the warranty

period. Any warranted part, which is scheduled for replacement as, required maintenance shall be warranted

for the period of time up to the first scheduled replacement point for that part. Maruyama Mfg. Co., Inc. is

liable for damages to other engine components caused by the failure of a warranted part still under warranty.

The purchaser is responsible for the performance of the required maintenance, as defined by Maruyama Mfg.

Co., Inc. in the Owner's/Operator's Manual.

EMISSION-RELATED PARTS WARRANTY: In addition to the above warranty coverage, Maruyama Mfg.

Co., Inc. will repair or replace, free of charge, for the original purchaser and each subsequent purchaser any

emission-related part or parts found to be defective in material and workmanship for two (2) years from origi-

nal retail delivery date except catalytic converter. Catalytic converter is warranted one year from origi-

nal retail delivery date. Emission-related parts are the carburetor assembly, the ignition coil

assembly, the ignition rotor and the spark plug, the catalytic converter and the fuel tank. Any replace-

ment part that is equivalent in performance and durability may be used in non-warranty maintenance or

repairs, and shall not reduce the warranty obligations of Maruyama Mfg. Co., Inc.

— US-2 —

This warranty does not cover the following:

1. Maintenance items (excluding defects in materials and workmanship) including hoses, spark plugs,

starter rope, air and fuel filters, clutch shoes, vibration isolators, throttle cables and all cutting attach-

ments, etc.

2. Extra expenses including shipping and handling, travel, payment for lost time or pay and for any inconve-

nience and storage.

3. Alterations or modifications including aftermarket parts not authorized by Maruyama U.S., Inc.

4. Wear, accident, abuse, neglect, misuse, negligence, improper fuels, lubricants, fuel mixtures (when

applicable), or failure to operate or maintain the product in accordance with instructions approved by

Maruyama.

Repair or replacement as provided under this warranty is the exclusive remedy of the consumer. Maruyama

shall not be liable for any incidental or consequential damages for breach of any express or implied warranty

on these products except to the extent prohibited by applicable law. Any implied warranty of merchantability

or fitness for a particular purpose on these products is limited in duration to the warranty period as defined in

the limited warranty statement. Maruyama reserves the rights to change or improve the design of the product

without notice and does not assume obligation to update previously manufactured products.

This warranty provides you with specific legal rights, which may vary from state to state.

It is the Owner's and Dealer's responsibility to make sure the Warranty Registration Card is properly filled out

and mailed to Maruyama U.S., Inc. Proof of purchase and registration will be required in order to obtain war-

ranty service.

To locate an Authorized Maruyama Servicing Dealer nearest you, contact:

Maruyama U.S., Inc.

4770 Mercantile Drive, suite100,

Fort Worth, TX 76137 U.S.A.

(940) 383-7400

[email protected]

www.maruyama-us.com

— US-3 —

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The U.S. Environmental Protection Agency (EPA), and Maruyama Manufacturing Company, Inc.

are pleased to explain the emission control system warranty on your small off-road engine. New

1997 and later model year small off-road engines must be designed, built and equipped, at the time

of sale, to meet the U.S. EPA regulations for small off-road engines. The equipment engine must be

free from defects in materials and workmanship which cause it to fail to conform with U.S. EPA stan-

dards for the first two years of engine use from the date of sale to the ultimate purchaser. Maruyama

Manufacturing Company, Inc. must warrant the emission control system on your small off-road

engine for the period of time listed above provided there has been no abuse, neglect or improper

maintenance of your small off-road engine.

Emission durability of 300 hours.

Your emission control system may include parts such as the carburetor or fuel injection system, the

ignition system, and catalytic converter. Also included may be hoses, belts, and connectors and

other emission related assemblies.

Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your

small off-road engine at no cost to you, including diagnosis (if the diagnostic work is performed at

an authorized dealer), parts, and labor.

MANUFACTURER'S WARRANTY COVERAGE:

The 1997 and later model year small off-road engines are warranted for two years. If any emis-

sion-related part on your engine is defective, the part will be repaired or replaced by Maruyama

Manufacturing Company, Inc. free of charge.

OWNER'S WARRANTY RESPONSIBILITIES:

(a) As the small off-road engine owner, you are responsible for the performance of the required

maintenance listed in your owner's / operator's manual.

Maruyama Manufacturing Company, Inc. recommends that you retain all receipts covering

maintenance on your small off-road engine, but Maruyama Manufacturing Company, Inc.

cannot deny warranty solely for the lack of receipts or for your failure to ensure the perfor-

mance of all scheduled maintenance. Any replacement part or service that is equivalent in

performance and durability may be used in non-warranty maintenance or repairs, and shall

not reduce the warranty obligations of the engine manufacturer.

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

WARNING

E23

E27

— US-4 —

(b) As the small off-road engine owner, you should be aware, however, that Maruyama

Manufacturing Company may deny you warranty coverage if your small off-road engine or a

part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

Company, Inc. service center as soon as a problem exists. The warranty repairs should be

completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact

Maruyama U.S., Inc. at 1-940-383-7400, or warranty@maruyama-us.com.

COVERAGE

Maruyama Manufacturing Company, Inc. warrants to the ultimate purchaser and each subse-

quent purchaser that your small off-road engine will be designed, built and equipped, at the time

of sale, to meet all applicable regulations. Maruyama Manufacturing Company, Inc. also warrants

to the initial purchaser and each subsequent purchaser that your small off-road engine is free

from defects in materials and workmanship which cause the engine to fail to conform with applic-

able regulations for a period of two years.

The 1997 and later model years, EPA requires manufacturers to small off-road engines for two

years. These warranty periods will begin on the date the small off-road engine is purchased by

the initial purchaser. If any emission-related part on your engine is defective, the part will be

replaced by Maruyama Manufacturing Company, Inc. at no cost to the owner.

Maruyama Manufacturing Company, Inc. shall remedy warranty defects at any authorized

Maruyama Manufacturing Company, Inc. engine dealer or warranty station. Any authorized work

done at an authorized dealer or warranty station shall be free of charge to the owner if such work

determines that a warranted part is defective. Any manufacturer-approved or equivalent replace-

ment part may be used for any warranty maintenance or repairs on emission-related parts, and

must be provided free of charge to the owner if the part is still under warranty, Maruyama

Manufacturing Company, Inc. is liable for damages to other engine components caused by the

failure of a warranted part still under warranty.

EPA considers emission-related warranted parts to include all the parts listed below. These war-

ranted parts are: the carburetor assembly, the ignition coil assembly, the ignition rotor, the

spark plug, the catalytic converter, and the fuel tank.

MAINTENANCE REQUIREMENTS

The owner is responsible for the performance of the required maintenance as defined by the

Maruyama Manufacturing Company, Inc. in the owner's / operator's manual.

LIMITATIONS

This Emission Control System Warranty shall not cover any of the following:

(a) repair or replacement required because of misuse or neglect, lack of required maintenance,

repairs improperly performed or replacements not conforming to Maruyama Manufacturing

Company, Inc. specifications that adversely affect performance and/or durability, and alter-

ations or modifications not recommended or approved in writing by Maruyama Manufacturing

Company, Inc., and

(b) replacement of parts and other services and adjustments necessary for required mainte-

nance at and after the first scheduled replacement point.

— US-5 —

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board (CARB), and Maruyama Manufacturing Company, Inc. are

pleased to explain the emission control system warranty on your 2013 small off-road engine. In

California, new small off-road engines must be designed, built and equipped to meet the State's

stringent anti-smog standards. Maruyama Manufacturing Company, Inc. must warrant the emission

control system on your small off-road engine for the period of time listed above provided there has

been no abuse, neglect or improper maintenance of your small off-road engine.

Your emission control system may include parts such as the carburetor or fuel injection system, the

ignition system, and catalytic converter. Also included may be hoses, belts, and connectors and

other emission related assemblies.

Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your

small off-road engine at no cost to you, including diagnosis, parts, and labor.

MANUFACTURER'S WARRANTY COVERAGE:

The 1995 and later small off-road engines are warranted for two years. If any emission-related part

on your engine is defective, the part will be repaired or replaced by Maruyama Manufacturing

Company, Inc.

OWNER'S WARRANTY RESPONSIBILITIES:

(a) As the small off-road engine owner, you are responsible for the performance of the required

maintenance listed in your owner's / operator's manual.

Maruyama Manufacturing Company, Inc. recommends that you retain all receipts covering

maintenance on your small off-road engine, but Maruyama Manufacturing Company, Inc.

cannot deny warranty solely for the lack of receipts or for your failure to ensure the perfor-

mance of all scheduled maintenance

(b) As the small off-road engine owner, you should be aware, however, that Maruyama

Manufacturing Company may deny you warranty coverage if your small off-road engine or a

part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

Company, Inc. distribution center as soon as a problem exists. The warranty repairs should

be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact

Maruyama U.S., Inc. at 1-866-783-7400, or warranty@maruyama-us.com.

Emission System Parts

Exhaust Emission

Carburetor

Muffler

Catalytic Converter

Ignition Coil / Magneto

Spark Plug

Air Filter

EGR Valve (piston)

Fuel Filter

Evaporative Emission

Fuel Tank

— US-6 —

Limited Warranty Statement ....................................... 1

Federal Emission Control............................................ 3

California Emission Control ....................................... 5

Contents....................................................................... 6

Introduction................................................................. 7

Safety........................................................................... 8

Operator Safety ...................................................... 8

Edger Safety........................................................... 8

Fuel Safety ............................................................. 9

Power Edger Operating Safety............................... 9

Safety and Instruction Decals ................................10

Product Description.....................................................11

Assembly.....................................................................12

Assembling Engine and Drive Shaft Assembly.....12

Loop Handle Installation........................................12

Connecting Stop Switch Wires ..............................13

Connecting Throttle Cable.....................................13

Installing Shield ................................................... 14

Installing Edger Blade ......................................... 14

Before Operation....................................................... 15

Oil and Fuel.......................................................... 15

Mixing Gasoline And Oil .................................... 16

Starting And Stopping ......................................... 17

Operation................................................................... 19

Operating Position ............................................... 19

Setting Depth of Cut ............................................ 20

Maintenance.............................................................. 20

Idle Speed Adjustment......................................... 20

Air Filter............................................................... 21

Fuel Filter............................................................. 22

Spark Plug............................................................ 22

Cylinder Cooling Fins.......................................... 23

Spark Arrester ...................................................... 23

Exhaust Muffler .................................................. 24

Flexible Drive Shaft Maintenance ....................... 24

Gearcase Maintenance ......................................... 25

General Cleaning and Tightening ........................ 25

Storage....................................................................... 26

Troubleshooting ........................................................ 27

Maintenance Period................................................... 27

Specifications............................................................ 28

Contents

Page US- Page US-

— US-7 —

Thank you for purchasing a Maruyama product.

Maruyama, it’s distributors, and dealers want you to be

completely satisfied with your new product. Please feel

free to contact your local Authorized Service Dealer for

help with service, genuine Maruyama parts, or other

information you may require.

Whenever you contact your Authorized Service Dealer

or the factory, always know the serial number of your

product. This number will help the Service Dealer or

Service Representative provide exact information about

your specific product. You will find the serial number

located in a unique place on the product (Product

Description on page US-11).

For your convenience, write the product model name

and serial number in the space below.

Read this manual carefully to learn how to operate and

maintain your product correctly. Reading this manual

will help you and others avoid personal injury and dam-

age to the product. Although Maruyama designs, pro-

duces and markets safe, state-of-the-art products, you

are responsible for using the product properly and safe-

ly. You are also responsible for training persons who

you allow to use the product about safe operation.

The Maruyama warning system in this manual identi-

fies potential hazards and has special safety messages

that help you and others avoid personal injury, even

death. DANGER, WARNING and CAUTION are sig-

nal words used to identify the level of hazard.

However, regardless of the hazard, be extremely care-

ful.

DANGER signals an extreme hazard that will cause

serious injury or death if the recommended precautions

are not followed.

Serial No.

Introduction

WARNING signals a hazard that may cause serious

injury or death if the recommended precautions are not

followed.

CAUTION signals a hazard that may cause minor or

moderate injury if the recommended precautions are

not followed. Two other words are also used to high-

light information. “Important” calls attention to special

mechanical information and “Note” emphasizes general

information worthy of special attention.

Safety

Operator Safety

1. Read and understand this Owner's / Operator's

Manual before using this product. Be thoroughly

familiar with the proper use of this product.

2. Never allow children to operate the Edger. It is

not a toy. Never allow adults to operate the unit

without first reading the Owner's / Operator's

Manual.

3. Always wear eye protection that complies with

ANSI (American National Standards Institute)

Z87-1.

4. Always wear hearing protection.

5. Always wear heavy, long pants, a long sleeved

shirt, boots and gloves. Do not wear loose cloth-

ing, jewelry, short pants, sandals, or go barefoot.

Secure hair so it is above shoulder length.

6. Never operate this Edger when you are tired, ill, or

under the influence of alcohol, drugs or medication.

7. Never start or run the engine inside a closed room

or building. Breathing exhaust fumes can cause

death.

8. Keep handles clean of oil, fuel and dirt.

Edger Safety

1. Make sure the Edger is assembled correctly and

that the Edger blade is correctly installed and

securely fastened as instructed in the Assembly

section.

2. Inspect the Edger before each use. Replace dam-

aged parts. Check for fuel leaks. Make sure all

fasteners are in place and tightened securely.

Follow the maintenance instructions beginning on

page US-20.

3. Make sure the Edger blade does not rotate at

engine idle speed. Refer to Idle Speed

Adjustment, page US-20.

4. Inspect the Edger cutting blade and replace any

parts that are cracked, chipped or damaged before

using the Edger.

5. Make sure the blade shield is installed and posi-

tioned correctly before using the Edger.

6. Never use a cutting blade or replacement parts that

are not approved by Maruyama.

7. Maintain the Edger according to the recommend-

ed maintenance intervals and procedures in the

Maintenance section on page US-20.

8. Shut off the engine and be certain the cutting

blade has completely stopped rotating before

inverting the Edger, performing maintenance on or

working on the machine.

— US-8 —

9. If running problems or excessive vibration occur,

stop immediately and inspect the unit for the

cause. If the cause cannot be determined or is

beyond your ability to correct, return the Edger to

your servicing dealer for repair.

Fuel Safety

1. Gasoline is highly flammable and must be handled

and stored carefully. Use a container approved for

fuel to store gasoline and/or fuel/oil mixture.

2. Mix and pour fuel outdoors, where there are no

sparks or flames.

3. Do not smoke near fuel or Edger, or while using

the Edger.

4. Do not overfill the fuel tank. Stop filling 1/4-1/2

inch (6 mm-13 mm) from the top of the tank.

5. Wipe up any spilled fuel before starting the

engine.

6. Move the Edger at least 10 feet (3 m) away from

the fueling location before starting the engine.

7. Do not remove the fuel tank cap while the engine

is running, or right after stopping the engine.

8. Allow the engine to cool before refueling.

9. Drain the tank and run the engine dry before stor-

ing the unit.

10. Store fuel and Edger away from open flame,

sparks and excessive heat. Make sure fuel vapors

cannot reach sparks or open flames from water

heaters, furnaces, electric motors, etc.

Power Edger Operating Safety

1. THIS EDGER CAN CAUSE SERIOUS

INJURIES. Read the instructions carefully. Be

familiar with all controls and the proper use of the

Edger.

2. Make sure the 3 mm hex wrench has been

removed from the gearcase and boss adapter

before you start the engine.

3. Avoid using the Edger near rocks, gravel, stones

and similar material which can become dengerous

projectiles.

4. Keep children, bystanders and animals outside a

50 ft. (15 m) radius from the operator and Edger.

5. If you are approached while operating the Edger,

stop the engine and Edger blade rotation.6. Never

allow children to operate the Edger.

— US-9 —

10 feet (3 m) Minimum

50 ft. (15 m Minimum)

— US-10 —

6. Never allow children to operate the Edger.

7. Use the Edger only in daylight or good artifical

light.

8. Never operate the Edger without proper guards or

other protective safety devices in place.

9. Do not put hands or feet near or under any rotating

parts. Keep clear at all times. Keep all parts of

your body away from the rotating Edger blade and

hot surfaces such as the muffler.

10. Keep firm footing and balance. Do not overreach.

11. Use the right tool for the job. Do not use the

Edger for any job that is not recommended by

Maruyama.

Safety and Instruction Decals

Safety decals and instructions are easily visible to the operator and are located near any area of

potential danger. Replace any decal that is damaged or lost.

ON SHAFT

(Part No.221501)

ON SHAFT

(Part No.221502)

ON SHAFT ON DEBRIS SHIELD

(Part No.223926) (Part No.221528)

Lubricate drive-

shaft each 30

hours of use.

— US-11 —

Product Description

1. Edger Blade

2. Debris Shield

3. Model Name

4. Safety Decal

5. Shaft Assembly

6. Loop Handle

7. Shaft Grip

8. Clutch Drum Housing

9. Engine

10. Serial Number

(on rear of engine)

11. Gearcase

12. Wheel

13. Throttle Trigger and Stop Switch

14. Throttle Cable and Stop Switch Wires

15. Fuel Tank

16. Air Filter

Assembly

Assembling Engine and Drive

Shaft Assembly

The drive shaft, clutch drum housing and gearcase are

assembled. Attach the clutch drum housing to the

engine using the four M5 x 20 screws supplied with the

unit.

Loop Handle Installation

The loop handle kit contains a package of four screws

and nuts, a rubber sleeve and the bottom clamp for the

loop handle.

1. Slip the rubber sleeve around the shaft approxi-

mately 9 inches (22.8 cm) from the end of the stop

switch/throttle trigger assembly for an initial han-

dle position.

2. Rotate the rubber sleeve so the split is to one side.

3. Place the loop handle and the bottom clamp over

the rubber sleeve.

4. Install the four screws and nuts. Leave the screws

finger-tight.

5. Reposition the loop handle up or down the drive

shaft to the most comfortable position, but no

closer than 9 inches (22.8 cm) from the end of the

stop switch.

6. Tighten the screws and nuts.

— US-12 —

Engine

M5 x 20 Screw (4)

Shaft

Clutch Drum Housing

Loop Handle

Screw (4)

Rubber Sleeve

Nut (4)

Bottom Clamp

Connecting Stop Switch Wires

1. Install the plastic tube (packed with the drive shaft

assembly) around the throttle cable and stop

switch wires.

2. Plug the stop switch wires into the matching con-

nectors from the engine. Note that wire polarity is

not important.

Connecting Throttle Cable

1. Loosen the knob and remove the air filter cover,

insert the throttle cable through the cable adjuster

sleeve on the carburetor bracket. Make sure the

end of the cable housing is seated positively in the

sleeve.

2. Position the slotted fitting on the carburetor so the

recessed hole for the cable lug is away from the

cable adjuster sleeve.

3. Rotate the carburetor throttle cam clockwise and

slip the throttle cable through the slot in the slot-

ted fitting, making sure the cable lug drops into

the recessed hole.

4. Operate the throttle trigger a few times to make

sure that it works correctly.

5. Adjust the cable adjuster sleeve so the stop on the

carburetor throttle cam just contacts the throttle

stop when the throttle trigger is fully depressed.

— US-13 —

Shaft Grip

Plastic Tube

Stop Switch Wires

Throttle Cable

Throttle Cable Housing

Cable Adjuster Sleeve

Locknut

Throttle Cable

Slotted Fitting

Recessed

Hole

Cable

Lug

Carburetor Bracket

Stop Switch WIres

Knob

Air Filter Cover

Cable Adjuster

Sleeve

Throttle Stop/Idle Speed

Adjuster Screw Bracket

Idle Speed

Adjuster Screw

Carburetor Throttle Cam

Slotted Fitting

6. When the throttle cable is adjusted correctly, tight-

en the locknut.

7. Reinstall the air filter cover and tighten the knob.

Installing Shield

1. Install the collar onto the plate stud.

2. Install the shield onto the plate stud, making sure

the shield stud fits into the matching slot in the

plate.

3. Install the flat washer, lock washer and hex nut

onto the plate stud.

4. Install the flat washer and knob onto the shield stud.

Installing Edger Blade

1. Install the boss adapter onto the attaching shaft out

of the gearcase.

2. Install the edger blade, clamping washer and blade

bolt.

Note: The blade bolt has left-hand threads.

3. Align the hole in the boss adapter with the hole in

the gearcase.

4. Insert the 3 mm hex wrench into the holes in the

boss adapter and gearcase to lock the attaching

shaft.

— US-14 —

WARNING

POTENTIAL HAZARD

• Foreign objects can be thrown by the

Edger.

WHAT CAN HAPPEN

• Contact with thrown objects can cause

personal injury.

HOW TO AVOID THE HAZARD

• Never operate the Edger without the

blade shield in place.

Gearcase

Attaching Shaft

Boss Adapter

Edger Blade

Blade Bolt (left

hand thread)

3 mm Hex Wrench

Clamping Washer

CAUTION

POTENTIAL HAZARD

• If the Edger blade is not adequately

tightened, it can come loose from the

Edger during use.

WHAT CAN HAPPEN

• This may cause damage to property or

personal injury.

HOW TO AVOID THE HAZARD

• Make sure the Edger blade is securely

fastened to the attaching shaft in the

gearcase.

Debris Shield

Shield Stud

Plate

Flat Washer

Hex

Nut

Lock

Washer

Collar

Plate Stud

Knob

5. Tighten the blade bolt to 100 in.-lbs. (11.3 N•M).

6. Remove the 3 mm hex wrench from the boss

adapter and gearcase.

Before Operation

Oil and Fuel

1. Do not smoke near fuel.

2. Mix and pour fuel outdoors and where there are

no sparks or flames.

3. Always shut off the engine before refueling.

Never remove the fuel tank cap while the engine is

running or just right after stopping the engine.

4. Always open the fuel tank cap slowly to release

any possible overpressure inside the tank.

5. Do not overfill the fuel tank. Stop filling 1/4-1/2

inch (6 mm-13 mm) from the top of the tank.

6. Tighten the fuel tank cap carefully but firmly after

refilling.

7. Wipe up any spilled fuel before starting the

engine.

8. Move the Edger at least 10 feet (3 m) away from

the fueling location and fuel storage container

before starting the engine.

— US-15 —

DANGER

POTENTIAL HAZARD

• In certain conditions gasoline is extreme-

ly flammable and highly explosive.

WHAT CAN HAPPEN

• A fire or explosion from gasoline can

burn you, others, and cause property

damage.

HOW TO AVOID THE HAZARD

• Use a funnel and fill the fuel tank out-

doors, in an open area, when the engine

is cold. Wipe up any gasoline that spills.

• Do not fill the fuel tank completely full.

Add gasoline to the fuel tank until the

level is 1/4” to 1/2” (6 mm to 13 mm)

below the bottom of the filler neck. This

empty space in the tank allows gasoline

to expand.

• Never smoke when handling gasoline,

and stay away from an open flame or

where gasoline fumes may be ignited by

a spark.

• Store gasoline in an approved container

and keep it out of the reach of children.

• Never buy more than a 30-day supply of

gasoline.

WARNING

POTENTIAL HAZARD

• Gasoline contains gasses that can build

up pressure inside a gas tank.

WHAT CAN HAPPEN

• Fuel can be sprayed on you when

removing gas cap.

HOW TO AVOID THE HAZARD

• Remove fuel cap slowly to avoid injury

from fuel spray.

10 feet (3 m) Minimum

Recommended Oil Type

Only use a two-cycle engine oil formulated for use in

high-performance, air-cooled two-cycle engines.

Maruyama brand 2-cycle oil is formulated for use in

high-performance, air-cooled two-cycle engines.

IMPORTANT: Do not use National Marine

Manufacturer’s Association (NMMA) or BIA

certified oils. This type of 2-cycle engine oil

does not have the proper additives for air-

cooled, 2-cycle engines and can cause engine

damage.

Do not use automotive motor oil. This type of

oil does not have the proper additives for air-

cooled, 2-cycle engines and can cause engine

damage.

Recommended Fuel Type

Use clean, fresh lead-free gasoline, including oxygenat-

ed or reformulated gasoline, with an octane rating of 89

or higher. To ensure freshness, purchase only the quan-

tity of gasoline that can be used in 30 days. Use of

lead-free gasoline results in fewer combustion chamber

deposits and longer spark plug life. Use of premium

grade fuel is not necessary or recommended.

Use of Fuel Additives

IMPORTANT: NEVER USE ALCOHOL,

GASOHOL CONTAINING MORE THAN

10% ALCOHOL BECAUSE ENGINE FUEL

SYSTEM DAMAGE COULD RESULT.

DO NOT USE FUEL ADDITIVES OTHER

THAN THOSE MANUFACTURED FOR

FUEL STABILIZATION DURING STORAGE

SUCH AS Maruyama’S STABILIZER/ CON-

DITIONER OR A SIMILAR PRODUCT.

Maruyama’S STABILIZER/CONDITIONER

IS A PETROLEUM DISTILLATE BASED

CONDITIONER/STABILIZER.

Maruyama DOES NOT RECOMMEND STA-

BILIZERS WITH AN ALCOHOL BASE

SUCH AS ETHANOL, METHANOL OR ISO-

PROPYL. ADDITIVES SHOULD NOT BE

USED TO TRY TO ENHANCE THE POWER

OR PERFORMANCE OF MACHINE.

Mixing Gasoline and Oil

IMPORTANT: The engine used on this Edger is

of a 2-cycle design. The internal moving parts

of the engine, i.e., crankshaft bearings, piston

pin bearings and piston to cylinder wall contact

surfaces, require oil mixed with the gasoline for

lubrication.

Failure to add oil to the gasoline or failure to

mix oil with the gasoline at the appropriate

ratio will cause major engine damage which will

void your warranty.

For your fuel premix, use Maruyama Premium

2-cycle Oil Mix, or equivalent ISO-L-EGD &

JASO FD oil with a minimum 89 octane high

quality gasoline. Maruyama 2-cycle oil is spe-

cially formulated to meet the requirements of

high-performance, low-emission air-cooled 2-

cycle engines. Use of other oils may lead to ser-

vice issues which may not be covered by your

warranty.

Fuel Mixture

The fuel: oil ratio is 50 parts gasoline to 1 part oil or

50:1.

Note: Never use a mixing ratio less than 50:1

regardless of the oil package mixing instructions.

Ratios less than 50:1, (for example, 60:1, 80:1,

100:1), reduce the amount of lubrication to the

internal moving parts of the engine and can cause

damage.

— US-16 —

50:1

Fuel Mixture Chart

Mixing Instructions

IMPORTANT: Never mix gasoline and oil

directly in the Edger fuel tank.

1. Always mix fuel and oil in a clean container

approved for gasoline.

2. Mark the container to identify it as fuel mix for

the Edger.

3. Use regular unleaded gasoline and fill the contain-

er with half the required amount of gasoline.

4. Pour the correct amount of oil into the container

then add the remaining amount of gasoline.

5. Close the container tightly and shake it momentar-

ily to evenly mix the oil and the gasoline before

filling the fuel tank on the Edger.

6. When refilling the Edger fuel tank, clean around

the fuel tank cap to prevent dirt and debris from

entering the tank during cap removal.

7. Always shake the premix fuel container momen-

tarily before filling the fuel tank.

8. Always use a spout or funnel when fueling to

reduce fuel spillage.

9. Fill the tank only to within 1/4-1/2 inch (6 mm-13

mm) from the top of the tank. Avoid filling to the

top of the tank filler neck.

Starting And Stopping

Before Starting The Engine

1. Fill the fuel tank as instructed in the Operation

section of this manual. (page15)

2. Rest the Edger on the ground.

3. Make sure the Edger blade is clear of any broken

glass, nails, wire, rocks or other debris.

4. Keep all bystanders, children and animals away

from the working area.

Cold Starting Procedure

This Edger is equipped with a fuel primer and idle start

system. To start a “cold” engine properly, perform the

following procedure:

1. Pump the primer bulb at the bottom of the carbu-

retor until fuel can be seen flowing through the

fuel return line to the fuel tank.

(Flowing fuel should be almost clear, not foamy or

full of bubbles.)

— US-17 —

Primer Bulb

Fuel

Return

Line

Gasoline 50:1 2-cycle oil

1 gallon 2.6 oz.

2 gallons 5.2 oz.

5 gallons 12.8 oz.

1 liter 20 ml

5 liter 100 ml

2. Move the choke lever to the closed ( ) position

and move the stop switch to the “ON” position.

3. Lock the throttle trigger in the fast-idle start posi-

tion, then pull the starter grip.

After the engine starts, squeeze and release the

throttle trigger to return it to the idle position, then

move the choke lever to the open ( ) position.

If the engine stops running before you move the

choke lever to the open ( ) position:

A. Go ahead and open the choke.

B. Make sure the throttle trigger is set to the idle

position.

C. Pull the starter grip until the engine starts.

Hot Restart

To start an engine that is already warmed up (hot

restart), or if the ambient temperature exceeds 68°F

(20°C):

1. Pump the primer bulb at the bottom of the carbu-

retor until fuel can be seen flowing through the

fuel return line to the fuel tank.

2. Move the choke lever to the open ( ) position

and move the stop switch to the “ON” position.

3. Leave the throttle trigger in the idle position and

pull the starter grip.

4. If the engine fails to start after three to four pulls,

follow the instruction in the Cold Starting

Procedure section (page19).

If the engine fails to start after you follow the

above procedures, contact an authorized

Maruyama dealer.

To Stop The Engine:

1. Release the throttle trigger.

2. Slide the stop switch to the “STOP” position.

— US-18 —

Starter Grip

Choke Lever

Stop Switch

STOP

START (ON)

Fast-idle lock

Throttle Trigger

(In fast-idle start

position)

Throttle Trigger

(In idle position)

➯

WARNING

POTENTIAL HAZARD

• The components of your recoilstarter

assembly are under high spring tension.

If improperly disassembled these parts

maystrike you with considerable force,

possibly causing personal injuly.

WHAT CAN HAPPEN

• Contact with the parts can cause sever-

er personal injury.

HOW TO AVOID THE HAZARD

• Never attempt to disassemble your

recoil starter assembly yourself.

Always consult your authorized

Maruyama dealer for repair by qualified

service technicians.

Operation

Operating Position

Before using the Edger, check the following:

1. Make sure the 3 mm hex wrench has been

removed from the gearcase and boss adapter

before you start the engine.

2. The Edger should be on the operator’s right side.

3. The operator’s right hand should be holding the

shaft grip, with his or her fingers on the throttle

trigger. The right arm should be slightly bent.

4. The left hand should be holding the loop handle

with the fingers and thumb fully enclosed around

the grip. The left arm should be extended.

Reposition the loop handle up or down the drive

shaft if necessary for a comfortable position.

5. The Edger weight should be evenly distributed

between the arms.

6. Adjust the Edger to the correct cutting depth

before you start the engine. (Refer to Setting

Depth of Cut on page 19.) Make sure the shield is

adjusted to shield the operator from thrown debris.

7. Make sure the blade is rotating (at least falf throt-

tle) before inserting the blade into the cut. The

Edger performs best at full throttle.

8. Always release the throttle trigger and allow the

engine to return to idle speed when not cutting.

9. Stop the Edger engine when moving between

work sites.

— US-19 —

Debris Shield

Increase the

Depth of Cut

Decrease the

Depth of Cut

Knob

Wheel

Hearing

Protection

Eye Protection

Right Arm

Slightly Bent

Left Arm Fully

Extended, Hand

Holding Loop Handle

Hand Holding

Throttle Grip, Fingers

on Throttle Trigger

Direction of Travel

Guard Adjusted to Clear

Blade, and Guard Operator

from Thrown Debris

WARNING

POTENTIAL HAZARD

• Foreign objects can be thrown by the

Edger.

WHAT CAN HAPPEN

• Contact with thrown objects can cause

personal injury.

HOW TO AVOID THE HAZARD

• Never operate the Edger without the

blade shield in place.

• Make sure the blade shield is correctly

positioned to shield operator from

thrown debris.

CAUTION

• Read the Safety instructions on page 8

concerning proper use of the Edger.

La page charge ...

Maruyama E27 Le manuel du propriétaire

Marque: Maruyama

Modèle: E27

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maruyama E27 Owner's manual
español: Maruyama E27 El manual del propietario

Maruyama E27 Le manuel du propriétaire

Ce manuel convient également à

Maruyama E27 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents