Elinchrom D-Lite RX ONE Manuel utilisateur

OPERATION MANUAL

GEBRAUCHSANLEITUNG

MANUEL D’UTILISATION

HANDLEIDING

English / Deutsch / Français / Nederlands

D-Lite RX One - 11.07.2013 NL vertaling ©Servix & Partners Belgium

El-Skyport Receiver RX built-in with full support for:

• EL-Skyport Transmitter Speed functions

• EL-Skyport Computer Remote Control

• EL-Skyport WiFi Remote Control for Apple

TM

Mobile devices

2

P.S: Technical data subject to change.

The listed values are guide values which may vary due to tolerances in components used.

Table of contents

English

Introduction 3

Declaration of conformity, disposal and recycling, CE marking 4

Safety notice and precaution 5

Basic features & advanced programmable features 6

Before you start / On-Off switch and fuse 7

Control panel 8

Reset the unit 9

Modelling lamp features & setup 9

Digital power display 10

Photocell / Eye-Cell / Automatic Mode 11

Photocell / Eye-Cell / Manual Mode 12

Charge Ready Beep Features & Setup 13

EL-Skyport Transceiver Features & Setup 14

Flash Power & Modelling Lamp Steps Per Touch 14

Flashtube Replacement / Error Management 15

Technical Data 16

EL-Skyport Transmitter Speed Instruction for user 17-22

Guarantee 128-129

3

The quality of light and exceptional performance is the result of long research, application of de-

manding principles, the long experience of ELINCHROM in lighting products for the studio and the

utilisation of the latest technology in this area.

Totally integrated to the range of ELINCHROM ﬂashes, the D-Lite RX ONE units maintain the tra-

ditional look and function that is ELINCHROM.

D-Lite RX ONE Compact Flash

Dear Photographer,

Thank you for buying your D-Lite RX ONE compact ﬂash unit.

All Elinchrom products are manufactured using the most advanced technology. Carefully selected

components are used to ensure the highest quality and the equipment is submitted to many controls

both during and after manufacture. We trust that it will give you many years of reliable service.

D-Lite RX ONE ﬂash units are manufactured for the studio and location use for photographers. Only

by observance of the information given, you can secure your warranty, prevent possible damage

and increase the life of this equipment.

This equipement has been tested and found to comply with the limits for a class B digital device, pursuant to Part

15 of the FCC Rules and meets all requirements of the Canadian Interference-Causing Equipement Regulations.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipement generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipement does not cause

harmful interferences to radio or television reception, which can be determined by turning the equipement off

and on, the user is encouraged to correct the interferences by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipement and receiver.

- Connect the equipement into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Elinchrom LTD is not responsible for any radio or television interference caused by unauthorised modiﬁcations

of this equipement or the substitution or attachment of connecting cables and equipement other than those

speciﬁed by Elinchrom LTD The correction of interference caused by such unauthorised modiﬁcation, substitution

or attachment will be the responsibility of the user.

FCC Class B Compliance Statement

Introduction English

4

!

Notational Conventions

The meaning of the symbols and fonts used in this manual are as follows:

Pay particular attention to text marked with this symbol.

Failure to observe this warning endangers your life, destroys the device, or may

damage other equipement.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

Product name: D-Lite RX ONE

Trade name: ELINCHROM

Model number(s): 20485.1

Name of responsible party: Elinchrom LTD

Av. De Longemalle 11

1020 Renens / Switzerland

Phone : +41 21 637 26 77

Fax: +41 21 637 26 81

Elinchrom LTD declares that the equipement bearing the trade name and model number speci-

ﬁed above was tested conforming to the applicable FCC rules, and that all the necessary steps

have been taken and are in force to assure that the production units of the same equipement will

continue to comply with the Comissions requirements.

Declaration of conformit English

CE Statements for EL-Skyport

This device has been tested and found to comply with the requirements set up in the council

directive on the approximation of the law of member states relating to EMC Directive 89/336/

EEC, low Voltage Directive 73/23/EEC and R&TTE Directive 99/5/EC.

CE marking

The shipped version of this device complies with the requirements of ECC directives

89/336/ECC «Electromagnetic compatibility» and 73/23/ECC «Low voltage directive».

Disposal and recycling

This device has been manufactured to the highest possible degree from materials

which can be recycled or disposed of in a manner that is not enviromentally

damaging. The device may be taken back after use to be recycled, provided that is

returned in a condition that is the result of normal use. Any components not reclaimed will be

disposed of in an environmentally acceptable manner.

If you have any questions on disposal, please contact your local supplier or your local

ELINCHROM agent (check our website for a list of all ELINCHROM agents world wide).

5

Notational Conventions

The meaning of the symbols and fonts used in this manual are as follows:

Pay particular attention to text marked with this symbol.

Failure to observe this warning endangers your life, destroys the device, or may

damage other equipement.

!

• Transport the ash unit with care, either in its original packaging or other corresponding

packaging ﬁt to protect it against knocks and jolts.

• Transport only in complete discharged conditions. Wait a minimum of 30 minutes after

disconnecting from the mains supply before packaging and transportation.

• Never drop the ash unit (danger of ashtube breakage)

Power cable

To guarantee safe operation, use the cable supplied.

• The cable has to be HAR-certied or VDE-certied. The mark HAR or VDE will appear on the

outer sheath.

• The cable set must be selected according to the rated current for your ash unit.

• Do not use a multiple adapter to connect one or more ash units per single mains socket.

• Flash systems store electrical energy in capacitors by applying high voltage.

• For your safety, never open or disassemble your ashes.

• Only an authorised service engineer should open or attempt to repair the units.

• Internal defect charge capacitors may explode whilst the unit is in use, never

switch on a working ﬂash unit, once it has been found to be faulty.

• Do not connect on the ash unit to mains supply without mounted modelling

lamp or ﬂash tube due to high voltage at the contacts!

Life Danger!

According to safety regulations, we draw your attention to the fact that these

electronic ﬂash units are not designed for use outdoors, in damp or dusty conditions and should

not be used after being exposed to sudden temperature changes causing condensation. They

must always be connected to an earthed (grounded) mains supply.

On no account should any object be inserted into the ventilation holes.

The units may retain an internal charge for a considerable time even though disconnected from

the power supply.

• Do not use without permission in restricted areas (like hospitals, etc.).

• Do not use in explosive environnements.

• Flash tubes and modelling lamps in use are very hot!

• Never touch a ash tube or lamp before the unit has cooled down and is disconnected from

the mains (min 30mn).

• Do not re ashes from short distance (less than 1m) directed at a person and avoid looking

directly into the ﬂashlight!

• Keep a min. 1m distance from any ammable materials.

• Keep generally distance to other operating units.

Safety Note English

Transport

Flash tubes and modelling lamps

6

Included basic features English

Additional advanced programmable features

The following basic features are easy to access and they are similar to previous Elinchrom compact

ﬂashes.

All the new features and functions can be customised.

Please read carefully how to conﬁgure the new features.

The VFC mode switches off the modelling lamp whilst the ﬂash unit recharges after a ﬂash has

been released. This function gives a visual check that all the studio ﬂash units have ﬁred.

The VFC mode can be activated together with the Ready Charge beep for maximum control.

Visual-Flash-Control (VFC)

When using compact ﬂashes of different powers, (e.g. 200 & 400 ws) the modelling lamp can be

reduced to -1 f-stop for better visual proportionality.

Proportional modelling lamp setup (PMS)

Some cameras may release before the main-ﬂash, several pre-ﬂashes to avoid the red eye effect. In

this case a normal photocell would respond and release a ﬂash with the ﬁrst pre-ﬂash of the camera.

To avoid incorrect synchronisation the intelligent Elinchrom Eye-Cell detects camera pre-ﬂashes.

The Eye-Cell function can be activated in “Automatic Mode” or in “Manual Mode”, even conﬁgure-

ing LED pre-ﬂashes. (Only for advanced users, read carefully the instructions before changing any

parameters).

“Eye-Cell” automatic & manual mode

The user can customise the Charge Ready Beep from short to long Beep signals.

The acoustical signal length can be set from 70 to 490 m/seconds.

Charge ready beep setup

To use the wireless triggering and changing ﬂash power settings, or to switch on/off the modelling

lamp, requires the optional EL-Skyport Transmitter.

“Group” and “ Channel Frequency” settings can be customised on each D-Lite RX ONE unit.

EL-Skyport wireless triggering & remote control

Normally ﬂash / modelling lamp power adjustments are in 1/10th steps per touch.

These steps can be changed from 1/10th to 7/10th or to 1 f-stop.

Power and modelling lamp steps setup

The cooling fan switches ON automatically if the unit temperature increases. The microprocessor

controls the unit temperature and the fan. If the ventilation is blocked or the fan does not work, the

display shows E8.

Temperature controlled FAN management

• Flash power up and down buttons

• Modelling lamp (

prop / min / max / off)

• Photocell on / off button

• Ready charge beep on / off button

• Test-ash button

• 3.5 mm synchronisation socket

• NEW EL-Skyport Wireless Triggering & Remote. Note: To function the integrated

Transceiver requires the optional EL-Skyport Transmitter.

7

The D-Lite RX ONE units are updated for operation on 90 – 260V/50 - 60 Hz. Before connecting

for the ﬁrst time, check to make sure that your Modelling Lamp coincides with the voltage. They

must always be connected to an earthed ( grounded) mains supply.

D-Lite RX ONE units have a

bayonet mount and locking ring ﬁtting, for ﬁxing all Elinchrom and Prolinca accessories.

The Reﬂector Bayonet supports Reﬂectors and Softboxes up to 1.5 kg, e.g. Rotalux 100 x 100 cm .

Mount the unit securely to a suitable stand or support.

Remove the black protective cover. DO NOT operate the unit without ﬁrst removing the black

protective cover.

1.Check that the modelling lamp voltage is correct.

2.Check that the mains switch (2) is in the position OFF ("O" position).

3.Insert the mains cable into the MAINS INLET (1) and connect this to a FULLY EARTHED OUTLET

4.Using the mains SWITCH (2), switch the unit ON ("I" position).

6.Select the power with the touch pad (10)

Operating instructions D-Lite RX ONE

(A) Locking ring

(C) Tilthead with locking

umbrella holder

(B) Protective cover

(26124)

Before you start ! English

Switch and fuse

Mains supply

Fuse for modelling light

Use only the Elinchrom mains cord. Switch off the unit before the mains cord is connected to

the mains plug.

Fast type 5 x 20mm, 4 AT

Switch off the unit and replace the blown fuse with a new one of the correct value.

The fastblow fuse will protect the triac of the modelling lamp circuit, the lamp and therefore

the ﬂash tube.

8

Overview of controls

1. Mains inlet socket includes the mains fuse

(slow blow)

2. Mains on/off switch

3. Modelling lamp fuse

4. Open ﬂash / Test button

5. Synch socket / 3.5 mm jack / low 5V sync

voltage

6. Digital multi display and charge / discharge

indicator*

7. Charge Ready Beep on/off

8. Eye-Cell on/off – programmable*

9. Eye-Cell receptor

10. Power up & down buttons and scroll /pro

gram buttons for advanced features setup*

11. Modelling lamp mode button (prop/min/

max/off/)

12. Tilt head with extra umbrella ﬁtting

13. Standard stand socket 5/8 inch

14. Centred umbrella tube for EL Umbrellas –

7 mm diameter

15. Knurled clamp screw

Control panel English

1

12

9

2

14

13

15

4

8

7

5

3

6

11

10

*The touches on this display are multifunctional to program / scroll the advanced features and to

setup the integrated EL-Skyport Transceiver. For programming please read carefully the following

pages!

9

Modelling lamps and fuses for 110 V & 230 V

Unit Modelling lamp 110V Modelling lamp 230V Socket Fuse

D-Lite RX ONE 100W / 23006 100W / 23002 E27 4AF

Programmable features - Reset English

Modelling lamp features & setup

How to „Reset“ the D-Lite RX ONE

In case you need to „RESET“ the D-Lite RX ONE to the manufacturer settings please follow the steps

below:

1. Switch the unit “off“

2. Press both ﬂash power up / down buttons (10) at the same time and switch the unit on

3. The Digital LED multi display (6) ﬂashes in fast mode

4. Do not continue to press the buttons, the resetting procedure is completed

Modelling lamp modes

* Do not use energy saving lamps

>

Setting: Press “Modelling” button to set Modelling lamp ON to proportional mode, min.

mode, max. mode, or OFF

> LED Indication: • LED is on: only in proportional mode.

• LED is off: in min. / max. / off mode.

!

• Please use only original ELINCHROM modelling lamps with a maximum power

of 100W ( effective 150W).

Setup Visual-Flash-Control (VFC) mode

Proportional modelling lamp setup (PMS)

> Enter VFC setup :

1. Press “Prop” push button for more than 2 seconds, until the display shows “F.X” (“X” is 0 or 1) to

enter into the Modelling lamp setup menu.

2

. Use the “Flash-Power” up and down button to change setting:

- “F.0”: Visual-Flash-Control = OFF. Modelling lamp remains ON after ﬂash.

- “F.1”: Visual-Flash-Control = ON. Modelling lamp switches off during recharging.

3. The display switches back to normal mode after approx. 4 seconds if no button is pressed. The

settings are automatically stored.

4. Standard setting is “F.0”, VFC = OFF

> Enter PMS setup:

1. Press “Prop” button for more than 2 seconds to enter into the Modelling lamp setup menu. The

display shows “F.X”, then press the “Prop” button once more to the PMS menu, the display shows

“-.X”

2. Use the “Flash-Power” up and down button to change the settings:

• “-.0”: PMS = OFF, Modelling lamp is set to maximum.

• “-.1”: PMS = -1 f-Stop, Modelling lamp is reduced by 1 f-stop.

(When using heads of different maximum power)

10

Sychronisation socket

Open ﬂash «test»

The standard photocell can be remotely triggered by another ﬂash unit!

The D-Lite RX ONE photocell is specially designed to work in studio light conditions

Direct light or other strong light sources may reduce the sensitivity of the cell.

Eye-Cell – advanced photocell sensor

Having pressed the touch pad to release a ﬂash, the green «READY» light

will appear again once the unit is recharged. If the green light does not

appear the charge system could be defective.

Please contact an authorized Elinchrom service centre.

Test and Ready (4)

5

Sync

Standard socket with 3.5 mm mini-jack (5).

N.B. Do not link ELINCHROM units by cable to other manufacturers sync. outlets.

ELINCHROM uses low voltage (5 V) for security reasons.

The ﬂash / modelling lamp power is displayed in f-stop compatible formats from 1.0 – 5.0 for

D-Lite RX ONE

. The ﬂash power difference from (e.g.) 4.0 – 5.0 is 1f-stop.

The power range is 5 f-stops, variable in 1/10th intervals. During charging or discharging, the

display «ﬂashes». In case of overheating or malfunction, the display shows “E” for error followed

by the error code number.

Display 1.0 2.0 3.0 4.0 5.0

Joules / Ws 6.25 12.5 25 50 100

Note: The «D-Lite RX ONE» units have an integrated discharge system, protected by a thermal

switch. To avoid overheating, discharge manually with the «test» button if you want to

decrease the power for more than 2f-stops.

Digital multi-display English

11

Intelligent Photocell-Sensor

Push “Cell” button, for less than 0.5 seconds to switch on/off the standard Photocell sensor.

LED Indication:

Cell LED is ON: Active photocell.

Cell LED is OFF: Inactive photocell.

If active, the Photocell sensor will trigger the ﬂash unit with any recognized ﬂash impulse.

The Eye-Cell offers new features and can detect camera pre-ﬂashes (anti red eye effect).

To customise the pre-ﬂash settings, please follow the instructions in paragraph 3.

(This is only activation, not the setup. To Setup, follow step 3)

Press the Cell button for approx. 1 second; the status LED starts ﬂashing.

LED Indication:

Cell LED ﬂashes in slow intervals; the Eye-Cell pre-ﬂash mode is activated.

Cell LED is OFF; the Eye-Cell pre-ﬂash mode is inactive.

Function:

In active mode the unit ignores up to 6 anti-red-eye ﬂashes and synchronizes / triggers only with

the last main ﬂash. This is useful where if the camera anti-red eye pre-ﬂashes can’t be switched

off.

Eye-CELL Setup English

Press the Cell button for 4 seconds until display shows “c.X” for automatic setup.

(“X” is the number of pre-ﬂashes including main ﬂash from 1 up to 7)

Scroll with the “Flash-Power” up and down button to “c.0”

Now use the camera-on ﬂash and release a test exposure. The camera will release several

anti-red eye ﬂashes (if activated). The D-Lite RX ONE Eye-Cell detects the number of ﬂashes

the camera released and stores the value automatically, and switches back to Eye-Cell Pre-ﬂash

mode. Ready to use.

If the cell button was pressed down for 6 seconds the “Setup Pre-Flash Timeframe” is

activated and the display shows t.4 or b.1 (standard settings). Do not change these values; this

would deactivate the “Automatic Eye-Cell Mode”! Wait a few seconds, the unit switches back to

the standard mode and the display shows the ﬂash power settings. Should the t.4 or b.1 values

have been changed, please set the “Setup Pre-Flash Timeframe” back to standard settings as

descript at paragraph 4.

Eye-Cell Functions

1. Standard Photocell mode

2. Eye-Cell pre-ﬂash mode

3. Automatic Eye-Cell Pre-Flash Setup

4. Manual Eye-Cell Pre-Flash Setup

5. Setup Pre-Flash Timeframe (only for advanced users)

3. Automatic Eye-Cell Pre-Flash Setup “c.0”

1. Using the Standard Photocell Mode

2. Eye-Cell Pre-Flash Mode

!

12

Change manufacturer settings only in case of problems with the auto-detection

of your camera pre-ﬂashes.

> Setting:

• Press Cell button for more than 6 seconds until display shows “t.X” (“X” is the value from 1 to 8)

• Use the Cell button to toggle between “t.X” and “b.X” settings.

• Use the “Flash-Power” up and down buttons to change the values.

• The display switches back to normal mode after approx. 4 seconds if no button is pressed.

The settings are automatically stored.

• Standard settings are:

---> t.4 (t. is the time window of all released anti red-eye ﬂashes incl. the main ﬂash).

---> b.1 (b. is the minimum time delay between two anti red-eye ﬂashes incl. the main ﬂash).

t. is the time window of all released anti red-eye ﬂashes incl. the mainﬂash. Change setting only

when the pre-ﬂash procedure is longer than the manufacturer settings.

Set the value t. between 1 and 8 to ensure that all pre-ﬂashes including the main ﬂash are inside

the time frame.

Pre-Flash Block Time Setting “b.X”: (Only For LED Anti Red-Eye Cameras)

Pre-Flash Block -Time: set the minimum delay between each pre-ﬂash.

Chose values between 0 and 7.

Value t 1 2 3 4 5 6 7 8

Time: [seconds] 1 2 3 4 5 6 7 8

A. Press Cell button approx. 4 seconds until display shows “c.X”.

(“X” is the number of settable pre-ﬂashes plus the main ﬂash from 1 up to 7)

B. With “Flash-Power” up and down button, set the number of pre-ﬂashes incl. mainﬂash.

C. The display switches back to normal mode after approx. 4 seconds if no button is pressed.

The settings are automatically stored.

D. Cell LED ﬂashes in fast intervals if the Eye-Cell pre-ﬂash mode is active.

> Recall The Eye-Cell Settings:

If you want to recall the actual Eye-Cell pre-ﬂash setting, repeat the steps A.

If you want to control the actual Eye-Cell pre-ﬂash setting, repeat the steps A to D.

Value b 0 1 2 3 4 5 6 7

Time: [miliseconds] 0 2 4 6 8 10 12 14

5. Setup Pre-Flash Timeframe (only for advanced users)

4. Manual Eye-Cell Pre-Flash Setup

Pre-Flash Timeframe Setting “t.X

!

13

Value A 1 2 3 4 5 6 7

Beep-On-Time in m/seconds 70 140 210 280 350 420 490

Charge Ready Beep Setup

• Setting

- Press “Audio” button, less than 0.5 seconds to switch the Charge Ready Beep

(ON / OFF)

• LED Indication

- Charge Ready Beep LED is on: Audio is active

- Charge Ready Beep LED is off: Audio is inactive (Mute)

• Changing Charge Ready Beep -On-Time Setting

- Press Audio button for more than 2 seconds until the display shows “A.X”

(“X” is the value from 1 up to 7)

- Use the Flash-Power” up and down button to change the value settings

- The display switches back to normal mode after approx. 4 seconds if no button was

pressed. The settings are automatically stored.

- Standard setting is: “A.3”

This feature creates a melody if settings are different between each unit to improve the acous-

tical recognition that all the ﬂashes have ﬁred and recycled.

Charge Ready Beep Features English

14

Integrated EL- Skyport Transceiver For Wireless Triggering – Setup

English

Group Settings

Frequency Channel Settings

EL-Skyport on / off

The EL-Skyport on / off, Group, Frequency Channel can be customised.

Press the ﬂash power up-down buttons together to enter into the “Advanced Feature Setup”

Display shows Change settings with the ﬂash power up-down buttons

r.0 EL-Skyport off

r.1 EL- Skyport on

r.2 EL-Skyport speed mode (only available with EL-Skyport Speed mod-

ules )

After 3 to 4 seconds the settings are saved automatically and the display shows the ﬂash power

setting.

Press the ﬂash power up-down buttons together to enter into the “Advanced Feature Setup”.

Then, scroll to G.1 using the Prop/Free button.

Display shows Select Group with the ﬂash power up-down buttons

G.1 Group 1 (standard setting)

G.2 Group 2

G.3 Group 3

G.4 Group 4

After 3 to 4 seconds the settings are saved automatically and the display shows the ﬂash power

setting.

Press the ﬂash power up-down buttons together to enter into the “Advanced Feature Setup”.

Then, scroll to F.1 using the Prop/Free button (only use in cases of interference with

other systems).

Display shows Change the Channel with the ﬂash power up-down buttons

F.1 to F.8 Select Frequency Channel from 1 – 8.

Note: The transmitter must have the same Frequency Channel

setting. Standard setting is Frequency Channel 1.

After 3 to 4 seconds the settings are saved automatically and the display shows the ﬂash power

setting.

Power Steps Per Push

Press the ﬂash power up-down buttons together to enter into the “Advanced Feature Setup”

Then, scroll to i.1 using the Prop/Free button.

Display shows Select values with the ﬂash power up-down buttons

i.0 +/- 1f-stop

i.1 +/- 1/10 (standard setting)

i.2 +/- 2/10

i.3 +/- 3/10

i.4 +/- 4/10

i.5 +/- 5/10

After 3 to 4 seconds the settings are saved automatically and the display shows the ﬂash

power setting.

15

If the unit does not ﬂash but the ON/OFF switch indicates that there is power, it could be that the

ﬂash tube needs replacing. Flash tubes have a long life with average use,

but multiflashing in long sequences can cause overheating of the electrodes

leading to premature ageing, or perhaps the flastube is broken or cracked.

To replace the ﬂash tube:

1. Switch off the mains switch

2. Remove the mains cable

3. Take the unit from its stand or lay it horizontally on a rigid surface. It will

need to be held ﬁrmly whilst removing and replacing the tube.

4. Allow the ﬂash tube and modelling lamp to cool for several minutes. They

may be very hot.

5. Carefully remove and store the modelling lamp.

6. Use a protective glove to remove the ﬂashtube:

A – Pull the ﬂash tube ﬁrmly out of the terminals

B – If the tube is broken, use security gloves. Avoid cutting yourself!

C - If the tube is broken, never touch the metal electrodes and ensure

that the unit is disconnected from the mains and discharged, wait min.

30 minutes! Use an insulated tool to pull out the electrodes.

7. Take the new ﬂash tube. A glove or "plastic protection" MUST BE USED.

Contact with your ﬁngers on the glas, will cause dark markings on the tube

when it is used.

8. Check that the tube is correctly aligned (central) and that the trigger contact

is gripping the tube.

9. Re-connect and test the unit as usual.

Flashtube replacement English

Error Management

E1

Overvoltage

detected

Switch unit OFF, wait 2 minutes and switch unit ON again. If the error shows

up again the unit requires a check up at the Elinchrom service centre

E2 Overheating

Wait until the unit has cooled down. The unit will switch back to normal

operation as soon as temperature decreases to normal working level.

E3

Auto dump

function fault

The Unit has detected a time out in the ADF mode. Switch the unit OFF,

wait 2 minutes and switch the unit ON again; use the Test release button for

power reduction. If the error shows up again the unit requires a check up at

the Elinchrom service centre.

E4 Charge fault

Unit has detected a time out during recharging. Switch unit OFF, wait

2 minutes and switch unit ON again. If the error shows up again the unit

requires a check up at the Elinchrom service centre.

E5

Mains supply

fault

Unit has detected a mains supply fault. Check your mains cord and mains

installation sockets. Switch unit OFF, wait 2 minutes and switch unit ON

again. If the error shows up again the unit requires a check up at the Elin-

chrom service centre.

E8

Fan manage-

ment fault

Unit has detected a FAN management problem due to overheating. Wait un-

til the unit has cooled down. Check if the FAN is blocked. If the error shows

up again the unit requires a check up at the Elinchrom service centre.

Error Fault Description

16

Ws / Joule J(Ws) 100

F-Stop

32.5

Power range f-stop

5

Power range Ws

J(Ws) 6-100

Power adjustment

f-stops 1/10 f-stops

Recycling time, min. / max. (230 V)

s 0.44 s / 1.5 s

Recycling time, min. / max. (115 V) s 0.45 s / 2.1 s

Flash duration t0.5 min. / max. s 1/1100 – 1/2200

Power stability 0.5%

Auto Power Dumping Applies power settings automatically

Voltage V Multi voltage, 90-260 V

Modelling lamp 100W/E27 - effective 150W

Modelling lamp setting Proportional, low, full, off

Flashtube Plug-in, user replaceable

Umbrella ﬁting Centred tube, for EL-umbrellas ø 7mm

Sync voltage 5V compatibility with digital cameras

Power consumption 230 V / 50 hz

no ﬂash / recycling

140 W / 310 VA

Power consumption 115 V / 60 hz

no ﬂash / recycling

190 W / 280 VA

EL-Skyport Integrated transceiver, 4 Groups, 8 Frequencies

Dimensions cm 18 x 19 x 14

Weight kg 0.9

D-Lite RX ONE Code 20485.1

Radio interference suppressiv CE-IEC 491 EN 60 555 - EN 61 000 - 4 - 2/3/4/5

Tolerances and speciﬁcations conforming to IEC and CE standards. Technical data subject

to change without notice.

Technical data D-Lite RX ONE

17

Contents :

Features 18

Battery Installation 18

Hot-shoe connector 17

Operating Instructions 18

Frequency Channel 19

Trigger Modes 19

Integrated SYNC Socket 20

Elinchrom RX Features 20

EL-Skyport Modules 21

Troubleshooting 21

CE Statements 22

FCC Compliance and

Advisory Statement 22

Disposal and recycling 22

User Manual

Transmitter Speed

19350

English

18

• SLR Camera Sync speeds: SPEED mode up to

1/250 s, STANDARD mode 1/160 - 1/200 s.

• 5 selectable trigger modes, (4 Groups + All)

• 8 frequency channels.

• 40 Bit security encryption.

• Up to 60 m range indoors for standard mode and

up to 40 m in speed mode.

• Up to 120 m range outdoors for standard mode

and up to 60 m in speed mode.

• Battery life up to 6 Months - over 30’000 ashes.

• RX-feature buttons (Remote Control).

• Test trigger button and feature button.

• Integrated Hot-shoe (middle contact) improved.

• SYNC-socket for direct connection improved.

• Two ash modes, standard and speed.

• The “Standard” mode is fully compatible with

previous EL-Skyport versions.

• The SPEED function is available for Ranger

Quadra AS, BXRi 250 / 500 und D-Lite RX ONE

and all other units, when used with the Universal

Hot-shoe with

screw lock and

SYNC socket

Battery drawer

Battery (19372)

Minus pole on top

Flexible swivel

Antenna 360 ̊

Fig. 1

Battery Installation

1. Pull the battery drawer out carefully.

2. Place the Lithium battery, see Fig. 1 for correct polarity.

3. Close the battery drawer.

! CAUTION:

• Ensure correct polarity / minus pole on top.

• Use only the Lithium Battery CR2430 3.0 V 19372.

• Remove battery if the EL-Skyport Transmitter is not used for some time.

• Never short-circuit battery poles.

• Avoid direct sunlight or temperatures above 45°C. The battery may explode!

Hot-Shoe Connector with Screw-Lock

The new Hot-shoe connector with screw-lock and middle contact synchronisation is designed to t digi-

tal and analogue cameras with maximum sync output of 3 V (the middle contact is the positive pole).

Operating Instructions

Speed.

• Status LED for EL-Skyport mode and battery

status.

• Improved housing, battery drawer and

switches.

• New Hot-shoe with screw-lock.

• New extra features; congure EL-Skyport with

the new EL-Skyport PC / MAC software 3.0.

You will appreciate the convenience of this

professional and powerful wireless device.

Note: Shutter speed and distance range are inuenced

by interference from other 2.4 GHz electronic equipment

and reections of ceilings, walls, oors, furniture, metall,

trees and humidiy in woods etc.

For better performance the Transmitter and Receiver

antenna should have direct sight, without any walls or

objects in - between.

EL-Skyport Transmitter SPEED //19350

Operating instructions :

2.4 GHz digital wireless Flash Trigger Transmitter

Features

EL-Skyport Transmitter Speed is designed with the latest 2.4 GHz Digital Wireless Technology.

English

19

Fig. 2

Flexible swivel

Antenna 360 ̊

Status LED

Flash Test / Flash Mode /

Conguration button

RX feature button

Power increase

or modelling lamp

toggle

RX feature button

Power decrease

Frequency

channel selector

MODE switch

GROUP switch

Frequency Channel

Note:

Transmitter and the corresponding Transceiver RX, the Universal Receiver or the EL units with

integrated EL-Skyport Receiver must have the same frequency channel settings!

Frequency

Channel

Slide Button conguration Frequency

/ Mhz

1 2 3

1 (default) Off Off Off 2456

2 On Off Off 2458

3 Off On Off 2460

4 On On Off 2462

5 Off Off On 2469

6 On Off On 2471

7 Off On On 2473

8 On On On 2475

EL-Skyport Sync Speed & Standard Mode

The SPEED function is available for Ranger Quadra AS, BXRi 250 / 500 und D-Lite RX ONE and all other

units, when used with the EL-Skyport Universal Speed.

Select “Speed” sync mode

Synchronises SLR cameras up to 1/250 s, or compact digital cameras up to 1/2850 s

- Select “Group” or “All” mode.

- Press test push button for minimum 5 seconds until the STATUS LED ashes two times.

- Release test push button.

- Now the EL-Skyport Transmitter Speed works in “SPEED” mode (r.2 mode).

Select “Standard” triggering mode

Synchronises SLR cameras up to 1/200 s, or compact digital cameras up to 1/1600 s

- Select “Group” or “All” mode.

- Press test push button for minimum 5 seconds until the STATUS LED ashes one time.

- Release test push button.

- Now the EL-Skyport Transmitter Speed works in “STANDARD” mode.

EL-Skyport Module Conguration:

Only possible with EL-Skyport PC / MAC software v 3.0 and higher.

- Power-Save Timer, individual programmable or disabled.

- Trigger delay is programmable from 250 ms up to 15 s.

- Download the FREE EL-Skyport Software from www.elinchrom.com

English

20

SET Cong Mode: (to congure included features)

- Switch module OFF.

- Hold test push button and switch TX ON.

- Keep test push button pressed until STATUS LED is ON.

 Check also EL-Skyport PC / MAC software 3.0 for changing Transmitter Speed setting.

The EL-Skyport Transmitter triggers the EL-Skyport Receiver modules in the following modes:

1. Off  Unit is OFF, no function.

2. Select Group - Group (1 to 4).

 Set switch to Group. and select Group 1 to 4.

 All corresponding EL-Skyport Receivers with the same selected Group (1 to 4) are triggered.

3. ALL Mode switch is set to ALL.

 All corresponding EL-Skyport Receivers are triggered regardless of which Group is selected.

Integrated Hot-Shoe SYNC 2.5 mm Socket

Use the included Sync cable to connect the integrated 2.5 mm Mono Jack socket with the camera or

lens PC socket directly.

EL-Skyport Transmitter SPEED RX Features

Compatible with Ranger RX, Style RX, Digital RX, BXRi 250 / 500, Ranger Quadra AS!

If the EL-Skyport Transmitter SPEED is used with the EL-Skyport Transceiver RX, BXRi 250 / 500

or the Ranger Quadra AS,

the following EXTRA

features are available:

Depending upon which Group is selected, the following RX-unit settings can be modied:

1. Flash power increase in 1/10 f-stops.

 press push button + to increase the power of selected Group of (or ALL) RX-units in 1/10 f-

stops.

2. Flash power decrease in 1/10 f-stops.

 press push button - to reduce the power of selected Group of (or ALL) RX-units in 1/10 f-stops.

3. Modelling lamp toggle.

 press and hold the push button +, 2 seconds or longer before releasing,

to toggle modelling lamp of the selected Group of (or ALL) RX-units.

Power save mode timer:

- After not using the Transmitter for 30 minutes the Power Save mode is active. To reactivate the

Transmitter, press the TEST push button.

- The Power Save mode timer can be congured with the EL-Skyport PC / MAC software v 3.0 and

higher.

Status LED:

- LED ashes every 4 seconds one time in “Standard” mode and two times in “Speed” mode.

- LED intensity correspond to the battery status - if off or very low => exchange the battery.

- LED is OFF if the Transmitter is switched OFF or in Power Save mode.

.

Reset to manufacturer default setting:

- Switch ON.

- Press test button for min 10 seconds.

English

La page charge ...

Elinchrom D-Lite RX ONE Manuel utilisateur

Elinchrom D-Lite RX ONE Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents