ProTemp PT-47-TTC User's Manual & Operating Instructions

MODEL NUMBERS

PT-16-TTC / PT-32-TTC / PT-47-TTC

User’s Manual &

Operating Instructions

GENERAL HAZARD WARNING:

FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH THIS

HEATER, CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE

FROM HAZARDS OF FIRE, EXPLOSION, BURN. ASPHYXIATION, AND/OR CARBON MONOXIDE POI-

SONING.

ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE OR

SERVICE THIS HEATER. IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN IN-

STRUCTIONS MANUAL, LABEL, ETC. CONTACT THE MANUFACTURER.

DANGER

CONSUMER: READ AND SAVE THESE INSTRUCTIONS

FOR OUTDOOR USE. INDOOR USE PERMITTED ONLY FOR:

The temporary heating of adequately ventilated buildings or

structures under construction, alteration or repair.

FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID COMBUS-

TIBLES, SUCH AS BUILDING MATERIALS, PAPER OR CARDBOARD, A SAFE DIS-

TANCE AWAY FROM THE HEATER AS RECOMMENDED BY THESE INSTRUCTIONS. NEVER USE

THE HEATER IN SPACES WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES,

OR PRODUCTS SUCH AS GASOLINE, SOLVENTS, PAINT THINNERS, DUST PARTICLES OR UN-

KNOWN CHEMICALS.

WARNING

Factory ID: 522

1 Industrial Blvd #101, Sauk Rapids, MN 56379 USA • Toll Free (800) 641-6996

Fax: 320-251-2922 • Web: www.protemp.us • Email: [email protected]

PTTB-403

PROPANE TANK TOP

HEATER

Locating Your Serial Number:

Your serial number can be found in the bottom left hand corner of the heater’s instruction hang-tag.

It will begin with the letters “PGTT” followed by 8 digits. For Example: PGTT12345678. Have your

Serial Number ready before calling customer service at 800-641-6996.

®

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

2

®

TABLE OF CONTENTS

Safety Information.........................................2-4

Speciﬁcations..................................................5

Features.......................................................5-6

What’s in the Box.............................................7

Assembly

.....................................................

8-9

Operation.................................................10-12

Maintenance and Storage................................12

Troubleshooting Guide....................................13

Exploded View

..........................................

...

.

.14

Parts List......................................................14

Warranty........................................................15

SAFETY INFORMATION

NOT FOR HOME OR RECREATIONAL VEHICLE USE.

WARNING

This is an unvented portable heater. It uses air (oxygen) from the area in which it is

used. Adequate combustion and ventilation air must be provided. Refer to VENTILA-

TION on Page 11.

WARNING

Carbon Monoxide Hazard This heater produces carbon monoxide, which has no

odor. Burning the heater in an enclosed space can kill you. Never use the heater in

enclosed spaces such as a tent, a camper, any vehicle or recreational vehicle (RV), enclosed shelter,

or any other enclosed areas.

DANGER

Not for use in residential living areas or in non-adequately ventilated enclosed spac-

es. Never bring or store a propane cylinder indoors.

DANGER

This heater is designed and approved for use as a construction heater in accordance with Standard

ANSI Z83.7-2011/CSA 2.14-2011. CHECK WITH YOUR LOCAL FIRE SAFETY AUTHORITY IF YOU

HAVE ANY QUESTIONS ABOUT APPLICATIONS. Other standards govern the use of fuel gasses and

heating products for speciﬁc uses. Your local authority can advise you about these.

If the information in this manual is not followed exactly, a ﬁre or explosion may re-

sult causing property damage, personal injury or loss of life.

DANGER

DO NOT OPERATE THIS HEATER UNTIL YOU HAVE READ AND THOROUGHLY UN-

DERSTAND THESE SAFETY AND OPERATING INSTRUCTIONS.

Failure to comply with the precautions and instructions provided with this heater can result in death,

serious bodily injury, property loss or damage from the hazards of ﬁre, explosions, burns, asphyxiation

or carbon monoxide poisoning. Only persons who can read and understand these instructions should

use or service this heater.

WARNING

This product contains chemicals, including lead, which are known to the State of

California to cause cancer and birth defects or other reproductive harm. For more

information go to www.P65Warnings.ca.gov.

WARNING

FOR OUTDOOR USE. INDOOR USE PERMITTED ONLY FOR: The temporary heating of

adequately ventilated buildings or structures under construction, alteration or repair.

WARNING

Do not use with or around birds, foul, or poulty.

DANGER

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

3

®

SAFETY INFORMATION

The products described in this manual are pro-

pane direct-ﬁred heaters. Direct-ﬁred means that

all of the combustion products of the heater enter

the heated space. This appliance is rated at 98%

combustion efﬁciency, but does produce small

amounts of carbon monoxide.

Carbon monoxide is toxic. Humans can tolerate

only small amounts of carbon monoxide and so

precautions should be taken to provide proper

ventilation. Failure to provide proper ventilation in

accordance with the instructions in this manual

can result in death.

People with breathing problems should consult a

physician before using this heater.

Early signs of carbon monoxide poisoning resem-

ble the ﬂu. Symptoms of improper ventilation /

carbon monoxide poisoning are:

Headache • Dizziness • Nausea • Dry Mouth

Sore Throat • Burning of Nose and Eyes

If you experience any of these symptoms:

GET FRESH AIR AT ONCE! Have your heater

serviced and check for proper ventilation. Some

people are more affected by carbon monoxide than

others. These include: pregnant women, those with

heart or lung problems, anemia or those under the

influence of alcohol or at high altitudes.

FOR OUTDOOR USE. INDOOR USE PERMITTED

ONLY FOR: The temporary heating of adequately

ventilated buildings or structures under construc-

tion, alteration or repair! Provide at least a three

square foot (2,800 sq cm) opening of outside air

for every 100,000 Btu / Hr heater rating. Refer to

“Ventilation” on page 11 for further instructions.

WHAT TO DO IF THE SMELL OF GAS IS PRESENT:

– DO NOT attempt to light the heater.

– Extinguish any open ﬂame.

– Shut off gas to heater.

– If odor continues, contact your local gas

supplier or ﬁre department.

– DO NOT touch or use any electric switch or any

electric device that can cause a spark.

– Immediately call your gas supplier from a

neighbors phone. Follow the gas suppliers

instructions.

– If you can not reach your gas supplier, call the

ﬁre department.

– Service must be done by a qualiﬁed service

agency.

NEVER store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this heater.

NEVER store

a propane (LP) cylinder not connected

to this heater in the vicinity of this heater.

NEVER

connect heater to an unregulated gas supply.

NEVER

obstruct the ﬂow of combustion and

ventilation air. (The front and rear of heater).

NEVER use duct work in front or rear of heater.

NEVER modify this heater or operate a heater that

has been modiﬁed.

NEVER service, move or handle heater while still hot

or operating

NEVER use heater in occupied dwellings.

NEVER use heater in a tent.

RISK OF INDOOR AIR POLLU-

TION!

WARNING

CARBON MONOXIDE POISONING

MAY LEAD TO DEATH!

DANGER

RISK OF BURNS, FIRE AND EX-

PLOSION!

WARNING

PROPANE IS AN

EXPLOSIVE GAS!

DANGER

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

4

®

Keep all combustible materials away from this heater.

Minimum Clearance From Combustibles

Sides Top Front Rear

36 in. 60 in. 60 in. 36 in.

ALWAYS install the heater so that it is not directly

exposed to water spray, rain, dripping water, or wind.

ALWAYS provide adequate clearance for accessibility,

combustion and ventilation (air supply) while heater

is operating.

– Use heater in accordance with all local codes.

In the absence of local codes, refer to The

National Fuel Code, ANSI Z223.1.

– This heater is shipped from the factory for use

with propane (LP) gas only. Do not convert

to any other gas. Installation must conform

to local codes, or in their absence, with the

standard for the Storage and Handling of

Liquefied Petroleum Gases ANSI/NFPA 58

and the Natural Gas and Propane Installation

Code CSA B149.1.

– Gas supply connections should be checked by

using a 50/50 soap and water solution. Never

use a ﬂame to check for gas leaks.

– Do not direct heater discharge towards the LP

cylinder unless it is at least 20 feet from the

heater.

– Use only the regulator and hose assembly

provided with this heater. Inspect the

regulator/hose assembly prior to each use of

the heater. If there is excessive abrasion or

wear, or if the hose is cut, replace it with the

proper assembly shown in the parts list, prior

to using the heater.

Minimum and Maximum Inlet Pressure

PT-16-TTC PT-32-TTC PT-47-TTC

Min. 5 PSI

Max. 200 PSI

SAFETY INFORMATION

The hose assembly shall be

protectedfromtrafc,building

material and contact with hot surfaces both dur-

ing use and while in storage.

WARNING

RISK OF FIRE! ALWAYS ATTACH THE HEATER IN AN UPRIGHT VERTICAL

POSITION. ALWAYS LOCATE HEATER ON A STABLE AND LEVEL SURFACE!

WARNING

CAUTION! HOT WHILE IN OPER-

ATION. DO NOT TOUCH. KEEP

CHILDREN, ANIMALS, CLOTHING AND COM-

BUSTIBLES AWAY FROM HEATER.

WARNING

For use with propane (LP)

gas only.

WARNING

DO NOT use any LP cylinder

larger than 20 lbs.

WARNING

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

5

®

FEATURES

PT-16-TTC

Regulator

SPECIFICATIONS

Model # PT-16-TTC PT-32-TTC PT-47-TTC

BTU 12 / 14 / 16,000 25 / 28 / 32,000 36 / 40 / 47,000

Fuel Consumption (Lbs./hr) 0.56 / 0.65 / 0.74 1.16 / 1.30 / 1.49 1.67 / 1.86 / 2.18

Maximum Operating Hours 35.9 / 30.8 / 27.0 17.2 / 15.4 / 13.4 12.0 / 10.8 / 9.2

Required Cylinder Lbs. 20 20 20

Fuel Type Propane Propane Propane

Heating Area (Ft.

2

) 300 / 350 / 400 620 / 700 / 800 900 / 1000 / 1175

Speciﬁcations subject to change without notice.

Front Guard

Heat Reﬂector

Rear Guard

Ignition Hole

Tip Over Switch

Safety Valve

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

6

®

FEATURES (CONT.)

PT-32-TTC

Regulator

Front Guard

Heat Reﬂector

Rear Guard

Ignition Hole

Tip Over Switch

Safety Valve

PT-47-TTC

Mounting Bolt Knob

Hose

Front Guard

Heat Reﬂector

Safety Valve

Mounting Bolt Knob

Hose

Rear Guard

Ignition Hole

Regulator

Tip Over Switch

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

7

®

WHAT’S IN THE BOX

PT-16-TTC

PT-32-TTC

PT-47-TTC

(1) Mount and Unit with

Single Burner Head

(1) Unit with Two Burner

Heads

(1) Mount

(1) Unit with Three Burner

Heads

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

8

®

ASSEMBLY

Model PT-32-TTC:

Tools Needed:

– Medium Phillips head screwdriver.

1. Place the tank collar bracket on top of the

center plate. Be sure the mounting bolt knob is

on bottom as shown in Figure 1.

2. Insert machine screw into top hole using

Phillips head screwdriver.

3. Insert 2nd machine screw into bottom hole.

This will secure the tank collar bracket to the

center plate.

Model PT-47-TTC:

Tools Needed:

– Medium Phillips head screwdriver.

1. Insert the mounting bolt knob into the tank

collar bracket.

2. Place tank collar bracket on the swivel bracket.

3. Place the plane washer on the tank collar

bracket and then insert the support bolt

(see Figure 2)

4. See Figure 3 on page 9 for determining burner

position options.

DO NOT adjust burner heads while heater is operating.

WARNING

Regulator

Knob

Fuel Connector Nut

Machine

Screws

Mounting Bolt Knob

Tank Collar Bracket

Tip over Switch

Assembly

Swivel

Manifold

Mounting

Bolt Knob

Plane Washer

Wing Nut

Regulator

Knob

Fuel Connector Nut

Tank Collar Bracket

Swivel Bracket

Figure 1 Figure 2

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

9

®

ASSEMBLY

PT-47-TTC (Continued):

– To have all 3 burners face front, the plane

washer should be to the right side of tank collar

bracket (see Figure 3).

– To have far left burner face back, the plane

washer should be to the left side of tank collar

bracket (see Figure 3).

Figure 3

Connecting Heater to LP Cylinder:

Be sure to read and understand all of the Safety

Information in this manual before connecting the

heater to the LP cylinder. Installation must conform

to local codes and with the Standard for the Storage

and Handling of Liquefied Petroleum Gasses and

ANSI/NFPA 58.

Inspect the hose and regulator prior to each use of

the heater. If there is excessive abrasion or wear,

or if the hose is cut, replace it with the proper

assembly shown in the parts list prior to using the

heater.

Model PT-16-TTC:

1. Be sure that the control knob on the regulator is

in the “OFF” position.

2. Line up the threads on the fuel connector nut

with the threads on the LP cylinder valve. Turn

fuel connector nut COUNTERCLOCKWISE to

tighten. Fully tighten the nut, being careful not

to over tighten.

3. Slowly open the LP cylinder valve.

Models PT-32-TTC / PT-47-TTC:

1. Be sure that the control knob on the regulator is

in the “OFF” position.

2. Line up the slots in the tank collar bracket

with the tank collar ring and slide into place.

Be sure the mounting knob is to the outside,

and tighten.

3. Line up the threads on the fuel connector nut

with the threads on the LP cylinder valve. Turn

fuel connector nut COUNTERCLOCKWISE to

tighten. Fully tighten the nut, being careful not

to over tighten.

4. Slowly open the LP cylinder valve.

Check all connections for leaks using a 50/50

mixture of dish-soap and water. Any bubbles that

appear show a leak. Remove and reconnect the

Connector Nut to the valve.

DO NOT direct the heater dis-

charge towards any propane

cylinder located within 20 feet of the heater.

WARNING

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

10

®

OPERATION

Propane Supply / Information:

Propane (LP)

This heater is not supplied with a propane cylinder.

Use only an approved propane cylinder.

LP Characteristics

– Flammable, explosive under pressure, heavier

than air and pools in low areas.

– In its natural state, propane has no odor, but

for your safety an odor that smells like rotten

cabbage has been added.

– Contact of propane (LP) gas with the skin can

cause freeze burns.

– Heater is manufactured for use with propane

gas only. DO NOT attempt to convert to any

other gas. Such modiﬁcations are dangerous

and will void the warranty.

– When heater is not in use, LP Cylinder must be

turned OFF.

– Be sure that the LP Cylinder is located on a

level and stable surface.

– DO NOT use this heater in a basement or below

ground level. Propane is heavier than air and

will always seek the lowest level. If you suspect

a leak, shut off the valve at the LP Cylinder

immediately.

The Propane (LP) cylinder must also be equipped

with the following:

– A collar to protect the gas valve.

– A shut-off valve terminating a LP cylinder valve

outlet as speciﬁed in the American National

Standard for Compressed Gas Cylinder Valve

Outlets and Inlets Connections.

– A safety relief valve having direct

communications with the vapor space of the LP

cylinder.

– The heater must operate on vapor withdrawal

from the operating cylinder.

The amount of Propane (LP) used with this heater

varies. Both factors are:

– The amount of gas in the cylinder of LP.

– The temperature of the LP tank and its

surroundings.

– Always keep LP cylinder fastened and upright.

– Avoid tipping the LP cylinder on its side when

connected to a regulator, since this may cause

damage to diaphragm in the regulator.

– Handle valves with care.

– Never connect an unregulated LP cylinder to a

construction heater.

– DO NOT subject LP cylinder to excessive heat.

– Tightly close the gas shutoff valve on the LP

cylinder after each use.

– All ﬁttings must be protected when

disconnected from the LP cylinder.

– Never store an LP cylinder inside a building or

in the vicinity of a gas burning appliances.

Propane is safe to use when

properly handled. Careless han-

dlingoftheLPcylindercouldresultinareand

or an explosion.

CAUTION

The disconnected tank must

never be stored in a building,

garage or any other enclosed area.

CAUTION

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

11

®

OPERATION (CONT.)

Ventilation:

– Risk of indoor air pollution and Carbon

Monoxide Poisoning.

– Refer to Safety Information on pages 2-4 for

information about Carbon Monoxide Poisoning.

– ALWAYS provide a fresh air opening in the

heated space of at least three square feet

(2,800 sq. cm) for each 100,000 BTU / Hr. of

heater output. Provide a larger opening if more

heaters are being used.

Minimum Ventilation Opening Needed

PT-16-TTC PT-32-TTC PT-47-TTC

0.5 ft.

2

1.0 ft.

2

1.4 ft.

2

460 cm

2

920 cm

2

1300 cm

2

Lighting Instructions:

1. STOP! Be sure to read all of the Safety

Information (See pages 2-4).

– ALWAYS Stand to the side or rear of the

heater.

– ALWAYS keep face and other body parts away

from the heater.

2. Check that the valve and propane cylinder

is open.

3. Turn the heater regulator knob CLOCKWISE to

the (OFF) position.

4. Wait five (5) minutes for any gas to clear.

Smell for gas around the heater, including

near the floor. If you do smell gas STOP!

Follow the safety instructions and check leaks.

If there is no gas smell proceed to the next

step.

5. Turn the regulator knob COUNTERCLOCKWISE

to the “HI” position.

6. Insert a lit match into the ignition hole in the

reflector. (See Figure 4)

7. Press the safety shut-off valve plunger for five

(5) seconds.

8. Mesh burner will light and glow red (continued

on Page 12).

CARBON MONOXIDE POISONING

MAY LEAD TO DEATH!

DANGER

Be sure to read and understand all

of the Safety Information in this

manual before lighting this heater.

WARNING

Heater has high surface

temperatures. Be sure to keep children,

pets and clothing away from the heater. Be sure

to keep burner and heater regulator clean and

free from any debris. Maintain safe distances

from heater as shown on Page 4.

CAUTION

NEVERuseaametocheckfor

leaks!

WARNING

Ignition Hole

Safety Shut-OFF

Valve Plunger

Heat Regulator Knob

Figure 4

NEVER look over the top of the

heater(reector).Thereisa

potentialforasmallashofameduringignition

that can cause serious bodily injury. ALWAYS stand

to the side or rear of the heater during ignition. DO

NOT allow any body part to touch the heater or be in

front of the heater during ignition.

WARNING

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

12

®

OPERATION (CONT.)

Lighting Instructions (cont.)

9. Once lit, keep the plunger depressed for thirty

(30) seconds. Then release the plunger, and

if the burner stays lit, remove and extinguish

the match. You will know that the burner is lit

when the mesh screen begins to glow red.

10. If the burner does not stay lit, repeat the

lighting process. If the heater does not light

after several attempts, be sure you are getting

fuel to the burner. The faint smell of gas will

tell you if the fuel is flowing. If not, there may

be a problem with your LP cylinder. Take it

back to your local dealer for replacement.

11. Once the burner is lit, turn Regulator Control

Knob to desired setting (HI) / (MED) / (LO ).

12. Light all burners when maximum heat is

desired. Follow Lighting Instructions steps

1-11. The second and third burner should be

lit separately. Do Not Attempt to light second

burner off the ﬁrst burner. Be sure NOT to

point burners at one another.

To Turn Off Heater:

1. Turn the valve on the LP cylinder CLOCKWISE to

stop the flow of fuel.

2. Turn the heater regulator knob to the (OFF)

position and wait at least fifteen (15) minutes for

the heater to cool.

3. Tightly close the gas shutoff valve on the LP

cylinder after each use.

4. Remove the heater from the LP cylinder by

reversing the steps in Connecting Heater to

LP Cylinder on Page 9. DO NOT store the LP

cylinder with the heater still attached or in an

enclosed area.

NOTE: ALWAYS INSPECT HEATER BEFORE USE

AND AT LEAST ANNUALLY BY A QUALIFIED

SERVICE PERSON.

EXTREMELY HOT during

operation. Do Not touch any

metal components while in operation. Keep

gasolineandanyotherammableliquidsaway

from the heater.

DANGER

Never bring or store a propane

cylinder indoors.

DANGER

DO NOT insert the lit match into

the air inlet holes in the mixing

tube.

CAUTION

MAINTENANCE AND STORAGE

1. Inspect your heater before each use. Check all

connections for leaks, following the procedure

outlined on Page 9. Check the Regulator Hose

(dual burner models only) for any cracks,

breaks or wear. If the hose is damaged replace

it with the correct manufacturers part. Heater

should be inspected before each use and once

annually by a qualiﬁed service person.

2. After use, always disconnect the heater

from the LP cylinder, and store the heater

separately from the tank. Be sure to close

the tank valve after use, and before storage.

The LP cylinder should be stored outdoors in

accordance with chapter 5 of the Standard for

Storage and Handling of Liqueﬁed Petroleum

Gases (ANSI/INFPA 58).

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

13

®

TROUBLESHOOTING GUIDE

Problem Possible Cause(s) Solution

Unit will not light.

1. Valve on propane cylinder

closed.

2. Propane cylinder empty.

3. Regulator not in (HI) position.

4. Defective regulator

1. Open cylinder valve by turning

COUNTERCLOCKWISE.

2. Reﬁll cylinder.

3. Turn regulator to (HI)

position.

4. Replace regulator assembly.

Burner will not stay lit

when gas valve plunger is

released

1. Tip switch activated or

defective.

2. Wire terminal connections

unplugged.

3. Defective thermocouple.

4. Defective MPU.

1. Place heater in upright position

or replace tip switch.

2. Check wiring connections.

3. Replace thermocouple.

4. Replace MPU.

Excessive ﬂames coming

out of burner, not glowing

red. Flames ﬂashback /

burn inside the mixing

tube.

1. Air inlet holes blocked or

covered.

2. Burner screen damaged.

3. Gap between burner screen and

burner can.

1. Clear any obstructions

2. Replace Burner screen.

3. Replace or repair burner head

assembly.

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

14

®

EXPLODED VIEW

4

1

3

2

PARTS LIST

Item # Description PT-16-TTC PT-32-TTC PT-47-TTC

1 Hose Assembly – 20-051-0001 20-051-0002

2 Thermocouple 20-091-0002 20-091-0002 20-091-0002

3 Mounting Bolt Knob – 20-503-0001 20-503-0001

4 Tipover Switch 50-017-0065 50-017-0065 50-017-0065

NEVER LEAVE HEATER UNATTENDED WHILE

BURNING OR WHILE CONNECTED TO A FUEL

SOURCE

15

®

LIMITED WARRANTY

Pinnacle Climate Technologies, Inc. warrants this heater to

the original retail purchaser only, to be free from defects in

material and workmanship for a period of one (1) year from

the date of initial purchase. This product must be properly

installed, maintained and operated in accordance with the

instructions provided.

Pinnacle Climate Technologies, Inc. requires reasonable

proof of your date of purchase from an authorized retailer

or distributor. Therefore, you should keep your sales slip,

invoice or cancelled check from the original purchase.

This Limited Warranty shall be limited to the repair or

replacement of parts, which prove defective under normal

use and service within the warranty period, and which

Pinnacle Climate Technologies, Inc. shall determine at its

reasonable discretion.

This warranty does not apply to products purchased for

rental use.

This Limited Warranty does not cover any failures or

operating difﬁculties due to normal wear and tear, accident,

abuse, misuse, alteration, misapplication, improper

installation or improper maintenance and service by you

or any third party. Failure to perform normal and routine

maintenance on the heater, shipping damage, damage

related to insects, birds or animals of any kind, and damage

due to weather conditions are also not covered.

In addition, the Limited Warranty does not cover damage to

the ﬁnish, such as scratches, dents, discoloration, rust or

other weather damage, after purchase.

All transportation costs for the return of damaged product

or parts will be the responsibility of the purchaser. Upon

receipt of damaged item, Pinnacle Climate Technologies,

Inc. will examine the item and determine if defective.

Pinnacle Climate Technologies, Inc. will repair or replace

and return the item, freight pre-paid.

If Pinnacle Climate Technologies, Inc. ﬁnds the item to be

in normal operating condition, or not defective the item

will be returned freight collect. This Limited Warranty is

in lieu of all other express warranties. Pinnacle Climate

Technologies, Inc. disclaims all warranties for products that

are purchased from sellers other than authorized dealers or

distributors.

AFTER THE PERIOD OF THE ONE (1) YEAR EXPRESS

WARRANTY EXPIRES, Pinnacle Climate Technologies,

Inc. DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING WITHOUT LIMITATION THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR APPLICATION. FURTHER, Pinnacle

Climate Technologies, Inc. SHALL HAVE NO LIABILITY

WHATSOEVER TO PURCHASER OR ANY THIRD PARTY

FOR ANY SPECIAL, INDIRECT, PUNITIVE INCIDENTAL,

OR CONSEQUENTIAL DAMAGES. Pinnacle Climate

Technologies, Inc. assumes no responsibility for any defects

caused by third parties. This Limited Warranty gives the

purchaser speciﬁc legal rights; a purchaser may have other

rights depending upon where he or she lives. Some states

do not allow the exclusion or limitation of special, incidental

or consequential damages, or limitations on how long a

warranty lasts, so the above exclusion and limitations may

not apply to you.

Pinnacle Climate Technologies, Inc. does not authorize any

person or company to assume for it any other obligation

or liability in connection with the sale, installation, use,

removal, return or replacement of its equipment, and no

such representations are binding on Pinnacle Climate

Technologies, Inc.

Always be sure to specify the model number and serial

number when making any claim with Pinnacle Climate

Technologies, Inc. For your convenience, use the space

provided below to list this information.

Model #:________________________________

Serial #:________________________________

Date of Purchase: ________________________

Locating Your Serial Number:

Your serial number can be found in the bottom left hand corner of the heater’s instruction hang-tag. It

will begin with the letters “PGTT” followed by 8 digits. For Example: PGTT12345678. Have your Se-

rial Number ready before calling customer service at 800-641-6996.

XXX-XXXXXXXX

Serial Number Label

1 Industrial Blvd #101, Sauk Rapids, MN 56379 USA • Toll Free (800) 641-6996

Fax: 320-251-2922 • Web: www.protemp.us • Email: [email protected]

NUMÉROS DE MODÈLES

PT-16-TTC/PT-32-TTC/PT-47-TTC

Manuel de l’utilisateur et

mode d’emploi

AVERTISSEMENT GÉNÉRAL DE DANGER :

LE NON-RESPECT DES MISES EN GARDE ET DES INSTRUCTIONS FOURNIES AVEC CETTE CHAUFFERETTE

PEUT ENTRAÎNER LA MORT, DE GRAVES BLESSURES ET DES DOMMAGES MATÉRIELS RÉSULTANT D’UN

INCENDIE, D’UNE EXPLOSION, DE BRÛLURES, D’ASPHYXIE ET/OU D’INTOXICATION AU MONOXYDE DE

CARBONE.

SEULES LES PERSONNES CAPABLES DE COMPRENDRE ET DE SUIVRE LES INSTRUCTIONS DOIVENT SE

SERVIR DE CETTE CHAUFFERETTE OU LA RÉPARER. POUR OBTENIR DE L’AIDE OU DES INFORMATIONS SUR

CETTE CHAUFFERETTE, TELLES QU’UNE NOTICE D’INSTRUCTIONS, UNE ÉTIQUETTE, ETC., COMMUNIQUER

AVEC LE FABRICANT.

DANGER

NOTE AU CLIENT : LIRE ET CONSERVER CE MANUEL POUR CONSULTATION ULTÉRIEURE

POUR USAGE EXTÉRIEUR. USAGE INTÉRIEUR PERMIS SEULEMENT

POUR :

le chauffage temporaire des structures ou des bâtiments bien ventilés

en cours de construction, de modification ou de réparation!

AVERTISSEMENT

RISQUE D’INCENDIE, DE BRÛLURE, D’INHALATION ET D’EXPLOSION. GARDER LES

MATÉRIAUX SOLIDES INFLAMMABLES, TELS LES MATÉRIAUX DE CONSTRUCTION, LE

PAPIER OU LE CARTON, À UNE DISTANCE SÉCURITAIRE DE LA CHAUFFERETTE, COMME RECOMMANDÉ DANS

LES PRÉSENTES INSTRUCTIONS. NE JAMAIS UTILISER LA CHAUFFERETTE DANS DES ENDROITS QUI

CONTIENNENT OU POURRAIENT CONTENIR DES MATIÈRES COMBUSTIBLES VOLATILES OU EN SUSPENSION

DANS L’AIR, OU ENCORE DES PRODUITS COMME DE L’ESSENCE, DES SOLVANTS, DES DILUANTS À

PEINTURE, DES PARTICULES DE POUSSIÈRE OU DES PRODUITS CHIMIQUES INCONNUS.

ID usine : 522

1 Industrial Blvd #101, Sauk Rapids, MN 56379 USA • Numéro sans frais (800)641-6996

Télécopieur : 320-251-2922 251-2922 • Web : www.protemp.us • Courriel : [email protected]

PTTB-403

CHAUFFERETTE SUR

BOUTEILLE DE PROPANE

Repérage du numéro de série :

Le numéro de série se trouve sur l’étiquette volante d’instructions de la chaufferette. Il commence par les lettres

«PGTT» suivies de 8 chiffres. Par exemple: PGTT12345678. Noter le numéro de série avant de contacter le

service à la clientèle au 800641-6996.

MD

NE JAMAIS LAISSER UNE CHAUFFERETTE SANS

SURVEILLANCE LORSQU’ELLE BRÛLE OU QU’ELLE

EST BRANCHÉE À UNE SOURCE DE COMBUSTIBLE.

bouteille de propane

2

MD

TABLE DES MATIÈRES

Consignes de sécurité ................................. 2-4

Spéciﬁcations ............................................... 5

Caractéristiques .......................................... 5-6

Contenu de la boîte ........................................ 7

Montage .................................................... 8-9

Mode d’emploi ....................................... 10-12

Entretien et entreposage ............................... 12

Guide de dépannage .................................... 13

Vue éclatée ................................................. 14

Liste des pièces ........................................... 14

Garantie...................................................... 15

CONSIGNES DE SÉCURITÉ

AVERTISSEMENT

Ceci est une chaufferette portative non raccordée, utilisant l’air ambiant (oxygène) de

l’espace où elle est utilisée. Une quantité d’air sufﬁsante pour la combustion et la

ventilation doit être fournie. Voir la rubrique «VENTILATION» à la page 11.

Danger lié au monoxyde de carbone Cette chaufferette produit du monoxyde de carbone, qui

n’a pas d’odeur. Utiliser cette chaufferette dans un espace clos peut causer la mort. Ne jamais

utiliser la chaufferette dans des espaces clos comme une tente, une autocaravane, tout véhicule ou véhicule

récréatif (VR), abri fermé ou tout autre type d’espace clos.

DANGER

Cet appareil n’est pas conçu pour une utilisation dans une aire résidentielle ou dans un espace

clos qui n’est pas ventilé adéquatement. Ne jamais apporter ou entreposer une bouteille de

propane à l’intérieur.

DANGER

Cette chaufferette est conçue pour les chantiers de construction en conformité avec ANSI Z83.7-2011/CSA 2.14-

2011. VÉRIFIER AVEC LE SERVICE LOCAL DES INCENDIES EN CAS DE QUESTIONS SUR L’APPLICATION.

D’autres normes régissent l’utilisation des gaz combustibles et des produits de chauffage pour des utilisations

spéciﬁques. Les autorités locales peuvent vous informer sur ces dernières.

Si les informations contenues dans ce manuel ne sont pas suivies à la lettre, un incendie ou une

explosion peuvent survenir et causer des dommages matériels, des blessures ou la mort.

DANGER

AVERTISSEMENT

NE PAS UTILISER CETTE CHAUFFERETTE AVANT D’AVOIR LU ET PARFAITEMENT

COMPRIS CES CONSIGNES DE SÉCURITÉ ET D’UTILISATION.

Le non-respect des précautions et instructions fournies avec cet appareil peut entraîner la mort, des blessures

corporelles graves, la perte ou des dommages aux biens causés par les risques d’incendie, des explosions, des

brûlures, d’asphyxie ou d’un empoisonnement au monoxyde de carbone. Seules les personnes qui peuvent lire et

comprendre les présentes directives doivent utiliser ou faire l’entretien de cette chaufferette.

AVERTISSEMENT

Ce produit contient des produits chimiques, dont du plomb, connus dans l’État de

Californie comme cancérigènes et causant des malformations congénitales ou d’autres

troubles de la reproduction. Pour de plus amples informations, consulter www.P65Warnings.ca.gov.

AVERTISSEMENT

POUR USAGE EXTÉRIEUR. USAGE INTÉRIEUR PERMIS SEULEMENT POUR : le

chauffage temporaire des structures ou des bâtiments bien ventilés en cours de

construction, de modiﬁcation ou de réparation!

Ne pas utiliser avec ou à proximité d'oiseaux, de volaille ni d'oiseaux de basse-cour.

DANGER

NE PAS UTILISER DANS LES HABITATIONS OU VÉHICULES RÉCRÉATIFS.

AVERTISSEMENT

NE JAMAIS LAISSER UNE CHAUFFERETTE SANS

SURVEILLANCE LORSQU’ELLE BRÛLE OU QU’ELLE

EST BRANCHÉE À UNE SOURCE DE COMBUSTIBLE.

bouteille de propane

3

MD

CONSIGNES DE SÉCURITÉ

Les produits décrits dans ce manuel sont des

chaufferettes à feu direct alimentées au propane. Feu

direct signiﬁe que tous les produits de combustion de la

chaufferette entrent dans l’espace chauffé. Cet appareil

est évalué à 98% de rendement de la combustion, mais

il produit de petites quantités de monoxyde de carbone.

Le monoxyde de carbone est toxique. Les êtres humains

peuvent en tolérer seulement de petites quantités; des

précautions doivent donc être prises pour assurer une

ventilation adéquate. Une ventilation non adéquate, en

violation des consignes ﬁgurant dans ce manuel, peut

entraîner la mort.

Les personnes atteintes de problèmes respiratoires doivent

consulter un médecin avant d’utiliser cet appareil.

Les premiers signes d’intoxication au monoxyde de

carbone ressemblent aux symptômes de la grippe.

Ces symptômes d’une mauvaise ventilation ou d’un

empoisonnement au monoxyde de carbone sont:

Mal de tête • Étourdissement • Nausée • Bouche sèche

Mal de gorge • Nez et yeux qui brûlent

Si un ou plusieurs de ces symptômes apparaissent :

SORTIR IMMÉDIATEMENT RESPIRER DE L’AIR FRAIS!

Faire vérifier ou réparer la chaufferette et vérifier que

la ventilation est adéquate. Certaines personnes sont

plus affectées que d’autres par le monoxyde de carbone.

Celles-ci incluent: les femmes enceintes, les personnes

ayant des problèmes cardiaques ou pulmonaires,

souffrant d’anémie ou qui se trouvent sous l’influence de

l’alcool ou à haute altitude.

POUR USAGE EXTÉRIEUR. USAGE INTÉRIEUR

PERMIS SEULEMENT POUR : le chauffage temporaire

des structures ou des bâtiments bien ventilés en cours de

construction, de modification ou de réparation! Fournir

une ouverture d’au moins 2 800 cm² sur l’air extérieur

pour chaque 29 kWh (100 000 BTU/h) du régime

nominal de la chaufferette. Voir « Ventilation » à la

page 11 pour plus de détails.

QUE FAIRE SI UNE ODEUR DE GAZ EST DÉTECTÉE :

– NE PAS tenter d’allumer la chaufferette.

– Éteindre toute ﬂamme nue.

– Couper l’alimentation en gaz vers la chaufferette.

– Si l’odeur persiste, contacter le fournisseur de gaz

local ou le service des incendies.

– NE PAS toucher ou utiliser un commutateur

électrique ou un appareil électrique qui pourrait

produire une étincelle.

– Appeler immédiatement le fournisseur de gaz à partir

du téléphone d’un voisin. Suivre les instructions du

fournisseur de gaz.

– Si le fournisseur de gaz ne peut être rejoint, appeler

le service des incendies.

– La réparation doit être effectuée par une agence de

service qualiﬁée.

NE JAMAIS entreposer ni utiliser d’essence ou d’autres

vapeurs ou liquides inﬂammables à proximité de cette

chaufferette ou de tout autre appareil.

NE JAMAIS entreposer une bouteille de propane (GPL)

non raccordée à cette chaufferette à proximité de

celle-ci.

NE JAMAIS

connecter la chaufferette à une alimentation

en gaz sans régulation.

NE JAMAIS obstruer le ﬂux d’air de combustion ni de

ventilation.

(À l’avant et à l’arrière de la chaufferette.)

NE JAMAIS utiliser de gaines ou de conduits d’air à

l’avant ou à l’arrière de l’appareil.

NE JAMAIS modiﬁer la chaufferette ou utiliser une

chaufferette qui a été modiﬁée.

NE JAMAIS déplacer ou manipuler l’appareil lorsqu’il est

encore chaud.

NE JAMAIS utiliser la chaufferette dans un logement

occupé.

NE JAMAIS utiliser la chaufferette dans une tente.

AVERTISSEMENT

RISQUE DE POLLUTION DE

L’AIR INTÉRIEUR!

L’EMPOISONNEMENT AU MONOXYDE

DE CARBONE PEUT ENTRAÎNER LA

MORT!

DANGER

AVERTISSEMENT

RISQUES DE BRÛLURES,

D’INCENDIE ET D’EXPLOSION!

LE PROPANE EST UN GAZ EXPLOSIF!

DANGER

NE JAMAIS LAISSER UNE CHAUFFERETTE SANS

SURVEILLANCE LORSQU’ELLE BRÛLE OU QU’ELLE

EST BRANCHÉE À UNE SOURCE DE COMBUSTIBLE.

bouteille de propane

4

MD

Garder tous les matériaux combustibles à l’écart de cette

chaufferette.

Dégagement minimal par rapport aux combustibles

Côtés Haut Avant Arrière

91 cm 152 cm 152 cm 91 cm

TOUJOURS installer la chaufferette de façon à ne pas

l’exposer directement aux brumes d’eau, à la pluie, à l’eau

de ruissellement ou au vent.

TOUJOURS fournir un espace sufﬁsant pour l’accessibilité,

la combustion et la ventilation (air) pendant le

fonctionnement de la chaufferette.

– Utiliser la chaufferette conformément à tous les

codes locaux. En l’absence de tels codes, consulter

le National Fuel Code, ANSI Z223.1.

– Cette chaufferette est expédiée de l’usine dans

le but d’être utilisée avec du gaz propane (GPL)

exclusivement. Ne pas la convertir pour un autre gaz.

L’installation doit être conforme aux codes locaux,

ou en leur absence, avec la norme du Storage and

Handling of Liquefied Petroleum Gases ANSI/NFPA

58 et du Code d’installation du propane et du gaz

naturel CSA B149.1.

– Vériﬁer les connexions d’alimentation en gaz avec

une solution de 50/50 d’eau et de savon. Ne pas

utiliser une ﬂamme pour détecter des fuites de gaz.

– La sortie de la chaufferette ne doit pas être dirigée

vers la bouteille de propane à moins qu’elle soit à

6m ou plus de distance.

– N’utiliser que l’ensemble de régulateur et de tuyau

fourni avec cette chaufferette. Inspecter l’ensemble

régulateur/tuyau avant chaque utilisation de la

chaufferette. Si l’abrasion ou l’usure est excessive,

ou si le tuyau est coupé, le remplacer par l’ensemble

qui convient, illustré dans la liste des pièces, avant

d’utiliser la chaufferette.

Pressions d’entrée minimum et maximum

PT-16-TTC PT-32-TTC PT-47-TTC

Min. 5 PSI

Max. 200 PSI

CONSIGNES DE SÉCURITÉ

AVERTISSEMENT

L’ensemble des tuyaux doit

être protégé contre la

circulation, les matériaux de construction et tout

contact avec des surfaces chaudes, durant l’utilisation

et pendant l’entreposage.

AVERTISSEMENT

RISQUE D’INCENDIE! TOUJOURS FIXER LA CHAUFFERETTE DANS UNE POSITION

VERTICALE. TOUJOURS PLACER LA CHAUFFERETTE SUR UNE SURFACE PLANE

ET STABLE.

AVERTISSEMENT

MISE EN GARDE! CHAUD

DURANT L’UTILISATION. NE

PAS TOUCHER. GARDER HORS DE LA PORTÉE DES

ENFANTS ET DES ANIMAUX ET À L’ÉCART DES

VÊTEMENTS OU DE TOUT MATÉRIAU COMBUSTIBLE.

AVERTISSEMENT

Pour être utilisé uniquement

avec du gaz propane (GPL).

AVERTISSEMENT

NE PAS utiliser de bouteilles

de plus de 20 lb (9 kg).

La page charge ...

ProTemp PT-47-TTC User's Manual & Operating Instructions

Ce manuel convient également à

ProTemp PT-47-TTC User's Manual & Operating Instructions

dans d''autres langues

Documents connexes

Autres documents