Hisense AEH-W0G1 Mode d'emploi

AEH-W0G1
Hisense
Marque
Hisense
Modèle
AEH-W0G1
Taper
Mode d'emploi
1
WIFI Module Instruction
System Operation Requirements
A. Smartphone System Requirements
The following are the minimum specifications needed to successfully run the
app on a smartphone:
Table 1 Smartphone requirements
Terminal device Android IOS
OS Android 6 or higher IOS 8 or higher
Resolution 1920*1080 or higher 960*640 or higher
2
B. Wireless Router requirements
Table 2： Wireless Router requirements
Standard IEEE 802.11b/g/n
Frequency Range 2.402-2.483.5GHz
Security 128 bits WPA-PSK/WPA2-PSK
Output Power 802.11b: 11dBM(11Mbps)
802.11g: 15dBM(54Mbps)
802.11n: 11dBM(72.2Mbps)
Data Rate 802.11b: 11Mbps
802.11g: 54Mbps
802.11n: 72.2Mbps
Sensitivity 802.11b: 11Mbps
802.11g: 54Mbps
802.11n: 72.2Mbps
Modulation QPSK+OFDM
Notice:
*Please try to use a certified 2.4G wireless router.
*The wireless router requirements are a general specification.
*Depending on the environment, there might be multiple WiFi access points
available. It is important to ensure that the correct one is being used.
*A router firewall may have high security or parental controls configured, and
these settings may block some required network ports for the device.
*The following network ports should be opened/whitelisted on your
router:80/443/55020/55030(Check the router’s user manual for instructions on
configuring firewalls.)
* The WiFi module does not support a new Wi-Fi certifed specifcation and non-
standard Wi-Fi certifcation type.
C. Description
Wifi Module in the Internet of things system is the role of home appliances
access Internet, and cloud linked, relying on cloud computing to achieve
intelligent home appliances .
3
picture 1: The function of WiFi module in the intelligent home appliance
system
Network standard
802.11 b/g/n
WiFi module parameters
Work environment：-20℃-85℃
Rated voltage：DC 3.3V
Maximum dissipation power：<500mA
Voltage fluctuation：±10%
RF Frequency Oscillator
The crystal oscillator circuit is building in at WiFi module X1.
Operating frequency range：Wifi：2412-2462MHz
WiFi
4
Modulation
：
WIFI: 11b: DBPSK, DQPSK and CCK and DSSS
11a/g: BPSK, QPSK, 16QAM, 64QAM and OFDM
11n: BPSK, QPSK, 16QAM, 64QAM and OFDM
Supported channels
：
1-11
Max.tune-up power with tolerance (AV value)
802.11 b mode: 12±1.0dBm
802.11 g mode: 10±1.0dBm
802.11 HT20 mode: 9±1.0dBm
802.11 HT40 mode: 10±1.0dBm
Antenna type: integral antenna
Antenna gain
：
1dBi
Crystal frequency
：
40MHz
5
WiFi module Interface
Pin Define Description
1 GND GND
2 IO14 PWM0
3 IO15 PWM1
4 IO0 PWM2
5 IO12 PWM3
6 IO5 PWM4
7 IO19 UART0_CTS,SPI1_CS,SPI0_CS,I2C0_SDA, TIMER5_TRIG
8 GND GND
9 GND GND
10 RX0 UART0_RXD,SPI1_CLK,SPI0_SCL,I2C1_SCL,TIMER4_TRIG
11 TX0 UART0_TXD,SPI1_MOSI,SPI0_MOSI,I2C1_SDA, PWM0
12 TX1 UART1_LOG_TXD
13 RX1 UART1_LOG_RXD
14 IO22 UART0_RTS,SPI1_MISO,SPI0_MISO,I2C0_SCL,PWM5
15 3.3V VCC 3.3V
16 GND GND
6
SAFETY Precautions
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation,Science and Economic Development Canada’s licence-exempt
RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause
undesired operation of the device.
RADIATION EXPOSURE STATEMENT
This equipment complies with Canada radiation exposure limits set forth for
uncontrolled environments. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
Cet appareil comprend un ou des émetteur(s) et récepteur(s) exempts(s) de
licence qui respecte(nt) les normes CNR applicables émises par Innovation,
Sciences et Développement économique Canada.
Son utilisation est soumise aux deux conditions suivantes :
(1) L’appareil ne doit pas causer d’interférence.
(2) L’appareil doit accepter toute interférence, incluant celles qui peuvent altérer
son fonctionnement.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible
d’en compromettre le fonctionnement.
7
DÉCLARATION D’IC SUR L’EXPOSITION AUX RADIATIONS:
Cet équipement est conforme aux limites d’ exposition aux radiations définies
par le Canada pour des environnements non contrôlés.Cet émetteur ne doit
pas être installé au même endroit ni utilisé avec une autre antenne ouun
autre émetteur.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Please notice that if the FCC identification number is not visible when the
module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the enclosed
module. This exterior label can use wording such as the following: “Contains
FCC ID: 2AGCCAEH-W0G1” any similar wording that expresses the same
meaning may be used.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of
20cm between the radiator & your body. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
The devices must be installed and used in strict accordance with the
manufacturer's instructions as described in the user documentation that comes
with the product.
Any company of the host device which install this modular with modular
approval should perform the test of radiated & conducted emission and
spurious emission, etc. according to FCC part 15C, 15B class B. Only if the
test result comply with FCC part 15C, 15B class B, then the host can be sold
legally.
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to
the modular transmitter
This radio transmitter 2AGCCAEH-W0G1 has been approved by Federal
Communications Commission to operate with the antenna types listed below,
with the maximum permissible gain indicated. Antenna types not included in
this list that have a gain greater than the maximum gain indicated for any type
listed are strictly prohibited for use with this device.
8
Antenna information
Manufacture: INNO Circuits Limited
Antenna Frequency
(MHz) Antenna Type MAX Antenna Gain
(dBi)
1 2412-2462 integral antenna 1
Please notice that if the ISED certification number is not visible when the
module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the enclosed
module. This exterior label can use wording such as the following: “Contains IC:
20778-AEHW0G1” any similar wording that expresses the same meaning may
be used.
l'appareil hôte doit porter une étiquette donnant le numéro de certification du
module d'Industrie Canada, précédé des mots « Contient un module d'émission
», du mot « IC: 20778-AEHW0G1» ou d'une formulation similaire exprimant le
même sens, comme suit
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This radio transmitter 20778-AEHW0G1 has been approved by Innovation,
Science and Economic Development Canada to operate with the antenna
types listed below, with the maximum permissible gain indicated. Antenna
types not included in this list that have a gain greater than the maximum gain
indicated for any type listed are strictly prohibited for use with this device.
Antenna information
Manufacture: INNO Circuits Limited
Antenna Frequency (MHz) Antenna Type MAX Antenna Gain
(dBi)
1 2412-2462 integral
antenna 1
9
Notice to OEM integrator
The module is limited to OEM installation ONLY.
The OEM integrator is responsible for ensuring that the end-user has no manual
instruction to remove or install module.
A separate approval is required for all other operating configurations, including
portable configurations with respect to Part 2.1093 and difference antenna
configurations.There is requirement that the grantee provide guidance to the
host manufacturer for compliance with Part 15B requirements.The module
complies with FCC Part 15.247 and apply for Single module approval.
Trace antenna designs: Not applicable.
Must use the device only in host devices that meet the FCC/ISED RF exposure
category of mobile, which means the device is installed and used at distances
of at least 20cm from persons.
The end user manual shall include FCC Part 15 /ISED RSS GEN compliance
statements related to the transmitter as show in this manual
(
SAFETY
Precautions).
Host manufacturer is responsible for compliance of the host system with
module installed with all other applicable requirements for the system such as
Part 15 B, ICES 003.
Host manufacturer is strongly recommended to confirm compliance with
FCC/ISED requirements for the transmitter when the module is installed in
the host.
Must have on the host device a label showing Contains FCC ID: 2AGCCAEH-
W0G1, Contains IC: 20778-AEHW0G1
The use condition limitations extend to professional users, then instructions
must state that this information also extends to the host manufacturer’s
instruction manual.
This module is stand-alone modular. If the end product will involve the Multiple
simultaneously transmitting condition or different operational conditions for a
stand-alone modular transmitter in a host, host manufacturer have to consult
with module manufacturer for the installation method in end system.
l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à
la fcc / (catégorie d'exposition rf mobile, ce qui signifie le dispositif est installé
et utilisé à une distance d'au moins 20 cm de personnes.le manuel de
l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité
relatives à l'émetteur que de montrer dans ce manuel.le fabricant est
responsable de la conformité de l'hôte, le système d'accueil avec le module
installé avec toutes les autres exigences applicables du système comme la
partie 15 b, ices - 003.accueillir le fabricant est fortement recommandé de
10
confirmer la conformité avec les exigences de la fcc / (émetteur lorsque le
module est installé dans l'hôte.le dispositif d'accueil doivent avoir une étiquette
indiquant contient FCC ID: 2AGCCAEH-W0G1 contient IC : 20778-AEHW0G1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Hisense AEH-W0G1 Mode d'emploi

AEH-W0G1
Hisense
Marque
Hisense
Modèle
AEH-W0G1
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents