Krups XP604050 Manuel utilisateur

Marque: Krups

Modèle: XP604050

Catégorie: Cafetières

Taper: Manuel utilisateur

www.krups.com

NC00023128-03

English . . . . . . . . . . . . . . . . . . p. 5

Français . . . . . . . . . . . . . . . . . p. 29

Español . . . . . . . . . . . . . . . . . p. 53

Réalisation : Espace Graphique

jk i

MAX

XP6040

WWW.KRUPS.COM

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:24 PageC1

90°

Max

"click"

MAX

fig. 1 fig. 2

fig. 3

fig. 4

fig. 5

fig. 6

fig. 7

fig. 8

fig. 9

fig. 10

fig. 11

fig. 12

fig. 13 fig. 14

fig. 15

fig. 16

fig. 17

fig. 18

fig. 21

fig. 19

fig. 20

FECHA DE COMPRA :

CANADA

GROUPE SEB

CANADA

345 Passmore Avenue

Toronto, ON

M1V 3N8

MEXICO

GROUPE SEB MEXICO

S.A. de C.V.

Goldsmith 38 Desp.

401 Col. Polanco

Delegacion Miguel

Hildalgo

11 560 Mexico D.F.

MEXICO

U.S.A.

GROUPE SEB USA

2121 Eden Road

Millville, NJ 08332

1-800-418-3325 01800 1128325 800-526-5377

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:24 PageC4

CONTENTS

IMPORTANT WARNINGS .............................................................................................................................p. 6

RECOMMENDATIONS .................................................................................................................................p. 8

TECHNICAL FEATURES AND ACCESSORIES ...................................................................................p. 8

PRODUCT DESCRIPTION ...........................................................................................................................p. 9

MAIN FUNCTIONS .........................................................................................................................................p. 9

FEATURES .........................................................................................................................................................p. 10

CONTROL PANEL FEATURES ...................................................................................................................p. 12

BEFORE FIRST USE ......................................................................................................................................p. 13

ESPRESSO SIDE

1. ESPRESSO PREPARATION....................................................................................................p. 15

2. HOT WATER FUNCTION .........................................................................................................p.17

3. STEAM FUNCTION ....................................................................................................................p. 18

4. DESCALING..................................................................................................................................p. 19

5. CLEANING AND MAINTENANCE..........................................................................................p. 20

COFFEE

1. COFFEE PREPARATION ..........................................................................................................p.22

2. DESCALING..................................................................................................................................p. 24

3. CLEANING AND MAINTENANCE..........................................................................................p. 24

SAFETY AND VISUAL WARNINGS ...........................................................................................................p. 25

RECYCLING......................................................................................................................................................p. 26

KRUPS GUARANTEE.....................................................................................................................................p. 26

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page5

IMPORTANT WARNINGS

When using an electrical appliance, basic safety instructions must always be observed to

reduce the risks of fire, electric shock and injury, in particular the following:

1. Read the instructions for use in full before using for the first time.

2. Do not touch hot surfaces. Use the handles or buttons.

3. To protect from fires, electric shocks and injuries, do not immerse the power cord,

plugs or the machine in water or any other liquid.

4. This machine is not designed for use by children.

5. Children should be closely supervised when the electrical appliance is used in their

proximity. Store away from the reach of children.

6. This appliance is not intended for use by people (including children) without prior

experience or knowledge with the machine, unless they are supervised or have been

given instructions on how to use the appliance by a person responsible for their

safety.

7. Children must be supervised to ensure that they do not play with the appliance.

8. Any contact with hot surfaces, hot water or steam can cause burns. Take care.

9. Take care when the steam spout is used as steam can cause burns.

10. Disconnect the appliance from the wall socket if it is not used for a few days and

before cleaning. Let the appliance cool down before installing or removing

accessories and before cleaning or storing.

11. All appliances are subject to strict quality controls. Practical tests are conducted on

randomly selected appliances, which may explain small marks or coffee remains in

the applicane before first use.

12. Do not use an electrical appliance whose power cord or plug is damaged, when the

appliance is not functioning correctly or is damaged in any way whatsoever. Return

all faulty appliances to the Krups Service Centre as soon as possible so that it can

be inspected, adjusted or repaired.

13. To reduce the risk of injury, do not leave the cord hanging over the table or counter,

where it can be pulled by a child or trip someone.

14. The cord must not hang over the table or counter or come into contact with hot

surfaces.

15. Never pour cold water in the coffee water tank immediately after a percolation cycle.

Let the appliance cool down between preparations.

16. Do not open the coffee lid during coffee production : scalding may occur.

17. Never leave the empty coffee pot on the warming plate while on.

18. The container is designed for use with this appliance. Never place the coffee pot on

a hotplate, in an oven or microwave.

19. Never place the hot coffee pot on a wet and/or cold worktop.

20. Never immerse the hot coffee pot in cold water.

21. The use of accessories that have not been recommended by Krups can cause fires,

electric shocks or injuries.

22. Do not use outdoors.

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page6

23. Do not place on or near to a gas burner, an electric hotplate or in a hot oven.

24. Stop the appliance with the button then disconnect from the wall socket. Do not pull

the cord but rather the plug.

25. Only use the appliance for its intended purpose.

26. Do not pour other liquids other than water and the anti-scale agent specified in this

manual into the water tank.

27. Protect the appliance from moisture and frost.

28. For domestic use only.

29. Do not use cracked container or a container having a loose or weakened handle.

30. Do not clean container with cleansers, steel wool pads, or other abrasive material.

31. To disconnect, stop the appliance with the button, then remove plug from wall outlet.

PLEASE KEEP THESE INSTRUCTIONS

NOTE

This appliance is designed for domestic use only. Any maintenance other than

cleaning and normal upkeep of the appliance by the owner should be performed by

Krups approved personnel only. Visit our website www.krupsusa.com in the USA

or www.krups.ca in Canada, or contact customer services at your nearest service

centre. To reduce risks of fire and electric shock, do not dismantle the base of the

appliance. All repairs should be performed by Krups approved personnel only.

INSTRUCTIONS FOR A SHORT POWER CORD

A. A short power supply cord is provided to reduce risk resulting from becoming

entangled in or tripping over a longer cord. The use of an extension lead is not

recommended with this appliance.

B. If an extension lead is absolutely necessary, it may be used if care is exercised

in their use.

1) The extension lead must have at least the same rating as that of the machine.

2) The extension lead must not hang over the table or counter where it could be

pulled by a child or trip someone.

C. This appliance is equipped with a polarised plug (one blade is wider than the

other). To reduce the risk of electric shock, there is only one way to insert the

plug into the socket. If it does not fully fit into the socket, return it. If it still does

not fit, contact a qualified electrician. Under no circumstances should the plug

be changed.

In order to improve its products, Krups reserves the right to modify specifications without

prior notice

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page7

RECOMMENDATIONS

To obtain an espresso which is rich in aromas and creamy to suit, the quality of the water, the temperature,

the variety of coffee, the roasting process, the fineness of the ground coffee, the dosage and the extraction

pressure are all determining elements.

Water

Always use clean fresh water and change the water every day. Water with a low mineral content is

preferred.

Temperature

For the first espresso or if multiple espressos are made during the day or if the machine is turned off

between each “Espresso moment”, it is recommended that you dispense the equivalent of 1 cup of hot

water as if you were making a espresso but without using ground espresso. In this way, the dispensing

unit, the filter holder, the filter and the cup get hotter, allowing the espresso to maintain the ideal

temperature for longer once in the cup.

Coffee roasting

It is possible to choose any type of coffee variety; the main thing is that it is fresh.

Coffee grinding

If the coffee is ground too finely, it will cause too much resistance to the hot water flow causing this to

overheat and “burn” the coffee, thus lending it a distinct bitterness. The coffee will be dispensed drop by

drop and the foam will not form in the cup. If the coffee is ground too coarsely it will provide no resistance

to the water flow. The infusion time is therefore too short. The coffee is not very creamy and does not

release enough aromas.

Important

Do not pour an espresso into a cup at room temperature. This will cause the temperature of the espresso

to cool too quickly. It is recommended that you turn on your machine 10 to 15 minutes before making the

espresso and rest the cups on the cup warming plate. It heats up quickly and reaches a temperature that

is sufficiently high enough to heat the cups quickly and efficiently.

TECHNICAL FEATURES AND ACCESSORIES

n Power: 1250 W

n Voltage: 120 V ~ 60 Hz

n Pump pressure: 19 bars

n Dimensions: L 15 x H 12.8 x P 11.4 inches

n Steel surface

n Pre-brewing of the ground coffee

n Electronic detection of water level

n Memory storage for 2 coffee sizes

n Automatic standby (after 30 mins)

n Reduction in brightness of TEMPERATURE light after 1 hour

n Product accessories: - 1 spoon

- One 1 cup filter

- One 2 cup filter

- One cleaning needle

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page8

PRODUCT DESCRIPTION

MAIN FUNCTIONS

Expresso

n An excellent espresso:

- 19 bar high pressure pump

- Pre-brewing of the ground coffee

- Filters with pressurization chamber for increased crema

n Ideal water:

- Thermo block heating unit for an ideal constant temperature

n Complete freedom of use:

- Compatible with ground coffee and all paper pods, both soft and compact

n Smart Cup rest grill with adjustable height:

- For special small espresso cups

- For mugs, large cups, dessert glasses...

n Ease of use:

- 2 sizes of espresso that are easy to program

- Water tank that can be accessed from the front.

English

ESPRESSO SIDE

a Stainless steel cup warming plate

b Group head

c Stainless steel body

d Rotating control button

d1 : PENDING setting:

●

d2 : HOT WATER function

d3 : STEAM function

e Adjustable HOT WATER/STEAM nozzle

f Spout nozzle

g Frothing nozzle

h Control panel

h1 : FILTER COFFEE light

h2 : FILTER COFFEE button

h3 : Preprogrammed 1 cup espresso button

h4 : Preprogrammed 2 cup espresso button

h5 : TEMPERATURE SELECTION button

- Expresso

- Hot water

- Steam

h6 : TEMPERATURE light

h7 : START/STOP button

i Removable water drip tray

j Stainless steel tray cover

k Stainless steel cup rest grill with adjustable

height

l Tray water level indicator

mButtons for adjusting the grill height

n Removable water tank

o Filter holder

p Filter holder dispensing spout

q 1 cup espresso filter

r 2 cup espresso filter

s Espresso dosing spoon

t Ground tamper

u Cleaning needle

COFFEE SIDE

A Warming plate

B Glass coffee pot

C Anti-drip device

D Removable filter holder for coffee grounds

E Water tank

F Water tank Max fill line

G Lid

H Coffee dosing spoon

I /

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page9

n Sophisticated design:

- 100% solid stainless steel cover

- Filter holder with professional dispensing spout

n Safety and comfort:

- EMPTY TANK detection with automatic pump stop

- Automatic standby when device is not used for more than 30 minutes

Filter coffee

n Performance:

- Capacity for up to 10 cups

- Glass coffee pot with water level markings/Removable lid

- Compatible with standard paper filters

n Ease of use:

- 1.5 liter tank with water level indicator

- Filter support with anti-drip system

- Keeps coffee warm for up to 2 hours.

n Safety:

- Heating stops automatically after 2 hours

FEATURES

The letters refer to the product description on page 9.

a. Stainless steel cup warming plate

Warms cups quickly and effciently, maintaining the ideal temperature longer.

b. Group head

The group head enables the locking of the filter holder.

c. Stainless steel body

The body of your espresso machine is stainless steel for better quality and longevity.

d. Rotating control button

The rotating button activates the HOT WATER or STEAM function.

e. Adjustable HOT WATER/STEAM spout

The adjustable spout allows distribution of the hot water or steam.

f. Spout nozzle

The spout nozzle enables the handling of the HOT WATER/STEAM spout without getting burnt.

g. Frothing nozzle

The frothing nozzle generates a smooth milk froth.

See page 17 for further information on using this nozzle.

i. Removable drip tray

The drip tray collects the overflow from the ESPRESSO maker. It is easily removable and should be

checked and emptied regularly.

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page10

k. Stainless steel cup rest grill

The perforated cup rest grill has markings for positioning cups.

l. Tray water level indicator

When a red signage is displayed on the indicator, the tank needs emptying.

m. Buttons for adjusting the grill height

The adjustment buttons allow you to adjust the cup rest grill based on the cups used:

- Low setting for large cups, dessert glasses and mugs

- High setting specifically designed for special espresso cups

n. Removable water tank

The tank can be removed from the machine for filling from the front of the machine. (See section "Filling

the tank" page 13).

Comments:

- Make sure the water never exceeds the maximum level for the tank.

- Make sure the water in the tank never passes below the minimum water level. Readjust the water

level regularly.

o. Filter holder

The filter holder has an ergonomic handle. To make your espresso, place one of the filters in the filter holder

and then add the ground coffee or pods. Position the filter holder on the group head to the far left then

turn it to the right to lock it into place.

q. 1 cup espresso filter

The cup size is identified on the bottom of the filter by the marking . This filter allows you to prepare 1

cup of espresso using ground coffee, a compact paper pod or a soft paper pod.

r. 2 cup espresso filter

The cup size is identified on the bottom of the filter by the marking . This filter allows you to prepare

2 cups of espresso using ground coffee.

Please note: it cannot be used with 2 pods at the same time.

s. Espresso dosing spoon

Well-leveled, it allows you to measure the quantity of coffee required for a good espresso.

t. Ground tamper

The ground tamper allows you to carefully tamp the coffee in the filter.

A. Warming plate

It allows you to maintain the temperature of your coffee for up to 2 hours.

B. Glass coffee pot

It can contain the equivalent of 15 small cups of coffee or 10 large ones.

Important: never place the coffee pot on a hotplate, in an oven or microwave.

C. Anti-drip device

If the coffee pot is removed before the coffee is done brewing, the anti-drip device prevents any more

coffee from being dispensed.

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page11

D. Removable filter holder for coffee grounds

To make your coffee, place a Krups #4 filter in the filter holder and position it in its compartment using the

2 handles.

E. Water tank

After opening the lid on the filter compartment, simply fill the tank with the quantity of water required.

Important: never exceed the "MAX" marking located close to the overflow.

F. Coffee tank overflow

If the water in the tank reaches the overflow opening, it will spill onto the counter. This situation must be

avoided, be careful not to overflowing the tank.

Important: never exceed the "MAX" marking located close to the overflow.

G. Lid

The lid is opened by simply pressing on both sides. The lid allows easy access to the tank and the coffee

filter holder.

H. Dosing spoon for filter coffee

It allows you to measure the quantity of coffee grounds required for a good filter coffee.

IMPORTANT

The filter coffee and espresso functions cannot be operated at the same time.

CONTROL PANEL FEATURES

The letters refer to the product description on page 9.

h1. FILTER COFFEE light

This light comes on while the coffee is being dispensed and while the coffee is being kept warm

(2 hours).

h2. FILTER COFFEE button

This button allows you to brew coffee depending on the quantity of water poured into the tank. Shortly

after brewing, the machine automatically switches to the keep warm function.

h3. PRE-PROGRAMMED 1 cup espresso button:

This button allows you to program a quantity of coffee corresponding to 1 cup (approximately 50 ml in a

pre-set dose, approximately 150 ml as a maximum dose) depending on the quantity pre-programmed.

Coffee production is stopped automatically, after the pre-programmed amount has been dispensed.

h4. PRE-PROGRAMMED 2 cup espresso button:

This button allows you to program a quantity of coffee corresponding to 2 cups (approximately 100 ml in

a pre-set dose, approximately 250 ml as a maximum dose) depending on the quantity pre-programmed.

Coffee production is stopped automatically, after the pre-programmed amount has been dispensed.

h5. TEMPERATURE SELECTION button: ,,

For the water to remain at an ideal temperature for making your beverages, the TEMPERATURE

SELECTION button must be positioned to the left for espressos or hot water and to the right for

steam .

I /

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page12

h6. TEMPERATURE light:

This light indicates:

a) When your machine is ready to produce espresso, hot water or steam:

- Light flashes = the espresso, hot water or steam mode is in progress

- Light is solid = the espresso, hot water or steam mode is ready to dispense

b) That the tank is empty (flashes quickly)

c) That the rotating control button should be set to PENDING (

●) during heating of your appliance

(flashes quickly)

h7. START/STOP button

Turn the button to the right (I) to turn the machine on – (the TEMPERATURE light (h6) comes on straight

away) and to the left (

●) to switch off.

BEFORE FIRST USE

n Open the machine and remove all the plastic bags, boxes and papers protecting the different parts.

Never leave the plastic bags in the reach of children.

n Also remove any self-adhesive labels that may be on the product cover or any other information leaflets.

n Remove detachable parts and clean in warm soapy water. Do the same with the other accessories.

n Wipe the appliance body and staineless steel tray cover using a soft wet cloth.

IMPORTANT

Any action performed on the machine must be done with the power cord

disconnected. Never place parts or accessories in the dishwasher.

Only the glass coffee pot is compatible with the dishwasher.

Never immerse the appliance, power cord or plug in any liquid.

n Ensure that all parts are completely dry before re-assembling.

n Place the cup rest grill on the water drip tray and slide it into the housing.

n Reposition the water tank by pushing it backwards toward the edge of the machine.

n Return the filter holder into its compartment.

n Position the coffee pot on the warming plate.

Filling the espresso water tank

To fill the tank:

n Remove the water tank by pulling it forwards using the central handle (Fig.1).

n Fill the tank with fresh water without exceeding the maximum water level.

n Return the tank into its housing by sliding it along the cup rest grill (Fig.2).

n Ensure that you have pushed it right to the end.

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page13

Draining and priming of the water circuit

Before using for the first time it is imperative that you allow the water to circulate through all of the

appliance’s circuits to remove any possible air and for the pump to be activated.

1. ESPRESSO SIDE

With the water tank full:

n Connect the power cord.

n Check that the rotating control button is set to PENDING (

●) and that the TEMPERATURE

SELECTION button (h5) is at ESPRESSO/HOT WATER .

n Check the FILTER COFFEE light (h1) is off and the FILTER COFFEE (h2) button is set on (

●)

setting.

n Switch the machine on by turning the START/STOP (h7) button to the right to the (I) setting.

n The TEMPERATURE light (h6) flashes slowly to indicate that the Thermo block is heating up.

(Approximately 1 minute).

IMPORTANT

While the TEMPERATURE light (h6) flashes, none of the ESPRESSO functions can be used.

n Place a large container under the HOT WATER/STEAM spout.

n When the TEMPERATURE light (h6) stops flashing, turn the rotating control button to the HOT WATER

function (Fig.3).

n The pump starts working at a steady rate and the hot water flows through the spout. Let it flow for

approximately 10 seconds.

n Stop the flow of water by simply returning the control button to PENDING (

●) (Fig.4).

n If there is no water flow, see the section “Safety and visual warnings”.

n Place a sufficiently large enough container under the dispensing unit without using the filter holder.

n When the TEMPERATURE light (h6) stops flashing, briefly turn the Pre-programmed 2 cup espresso

button to the right and let the water flow (the machine’s pump stops automatically when the

pre-programmed amount has been dispensed). If this does not work, see the paragraph “Safety and

visual warnings” p.25 and perform this action again.

IMPORTANT

It is possible that some steam may be released from the water tank. This is completely normal.

The water circuit has now been drained and your machine is ready for use.

2. COFFEE FUNCTION

n Check that the power cord is connected.

n Open the lid by pressing on both sides and open the lid to 90° without forcing (Fig.5 and 6).

n Fill the tank without exceeding the MAX marking at the overflow opening (Fig.7 and 8).

n Ensure that the filter holder is correctly positioned (i.e. fully inserted into its opening).

n Place a paper filter in the filter holder and fill it with ground coffee using the measuring spoon, with one

spoon per cup of coffee.

n Close the lid until you hear the click indicating that it is firmly locked (Fig.11).

n Position the coffee pot on the warming plate.

n Check that the rotating control button is set to PENDING (

●) (fig.4) and the START/STOP (h7) button

is set to (

●).

n Push the FILTER COFFEE button to the right; the COFFEE FILTER light (h1) comes on and the

coffee is dispensed after a few seconds.

n After all the water has been dispensed, turn off the appliance and let it cool.

I /

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page14

n Remove the coffee pot from the warming plate and pour away the water.

ESPRESSO SIDE

1. ESPRESSO PREPARATION

Espresso coffee is obtained by passing pressurized hot water through coffee grounds. The quality of the

taste depends on several factors: the type of coffee, the fineness of the ground coffee, the quantity of

ground coffee in the filter and the quality of the water…

The XP6040 espresso machine allows you to prepare a delicious espresso from ground coffee or a paper

coffee pod.

IMPORTANT

It is recommended that you turn the machine on 10 to 15 minutes before making your espresso

and pre-heat the cups on the cup warming plate. Your coffee will then stay at the ideal temperature

longer in a cup that has been preheated.

A. Espresso made from ground coffee

n Choose the 1 cup filter or the 2 cup filter depending on the quantity of coffee required and

place in the filter holder. (fig.5).

n Fill the dosing spoon taking car to level it:

- 1-cup filter = 1 spoon of ground coffee (approximately 7 g)

- 2-cup filter = 2 spoons of ground coffee (approximately 14 g)

n Empty the contents of the spoon into the filter then gently shake to distribute the ground coffee

uniformly.

n Press down the ground coffee using the ground tamper. If the coffee seems too light, press the coffee

more.

n If necessary, wipe the edge of the filter to remove any ground coffee that may be stuck and thus help

the filter holder lock into the dispensing unit.

B. Espresso made from paper pods

IMPORTANT

There are 2 types of paper pods:

- The "compact" pod = special espresso coffee packaged in a rigid pod (approx. 45 mm in

diameter) composed of 7 g of compacted ground coffee.

- "Soft" pod = pod measuring 55 to 60 mm in diameter. Since this type of pod is not specifically

designed for espresso machines, you will obtain a weaker coffee than with a “compact” pod.

n Use the 1 cup filter and insert either a compact or a soft pod.

Important

Do not use the 2 cup filter with paper pods.

n Since the shape of the paper pods can differ from one brand to another, , take care to center the pod

in the filter and push gently so that the sides fit.

IMPORTANT

If necessary, fold the sides of the paper pod inside the filter to prevent it from overhanging. This

will ensure that coffee will not leak outside the filter holder and prevent any damage.

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page15

C: Espresso function

Preparing the machine

n Check the water level in the tank and fill if necessary.

n Check that the rotating control button is set to PENDING (

●) and that the TEMPERATURE

SELECTION button (h5) is at ESPRESSO/HOT WATER .

n Switch the machine on by turning the START/STOP button (h7) to the (I) setting.

n The TEMPERATURE light (h6) flashes.

IMPORTANT

While the TEMPERATURE light (h6) flashes, none of the ESPRESSO functions can be used.

n Insert the filter holder into the group head by aligning the handle with the marking "INSERTION" and

lock by moving the filter holder from left to right (Fig.15).

Adjusting the cup rest grill

The height of the cup rest grill can be adjusted.

n When using large cups, dessert glasses and mugs, leave the grill on the bottom level.

n When using espresso cups, raise the cup rest grill by pressing on the 2 height adjustment buttons at

the same time (Fig.13).

IMPORTANT

To return the cup rest grill to the lower level, press the 2 adjustment buttons at the same time.

n Place 1 or 2 cups (as necessary) on the cup rest grill and check that it/they are correctly positioned

under the dispensing spout of the filter holder, using the cup positioning marks (fig.14).

Coffee preparation

n Wait until the TEMPERATURE light (h6) stops flashing, therefore indicating that the appliance has

reached the optimum temperature for making an espresso coffee. Your appliance is now ready for use.

n Turn the espresso button or to the right to activate the ESPRESSO function. The pump operates

briefly to pre-wet the ground coffee and then stops for a few seconds and starts again to dispense the

coffee.

IMPORTANT

This pre-brewing process ensures even greater release of the coffee aroma.

n When the volume of coffee has been reached, the appliance stops automatically.

Important

By default, the volume of coffee for "1 cup" is 50 ml; for "2 cups" it is 100 ml.

n Wait a few seconds until the surplus water in the thermo block has been drained (until the “suction

noise” has stopped).

NOTE

A little steam may be released from the water tank. This is completely normal.

n Remove the cup(s) then unlock the filter holder by turning it from right to left until it can be

released from the group head.

Important

Be careful as some steam may be released from the dispensing unit.

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page16

Cleaning the filter and filter holder

n Empty the filter using a small spoon or carefully tapping it against a surface so that any coffee grounds

can be collected.

n Remove the filter.

Important

The metal parts on the filter holder and filter are very hot.

n Rinse the filter and filter holder under hot water and dry.

D. Pre-programmed settings

The stainless steel XP6040 automatic espresso machine allows you to pre-program 2 volumes of

espresso coffee very simply.

IMPORTANT

Two volumes of coffee can be programmed by default into your machine:

- Pre-program 1 (1 cup): 50 ml approximately

- Pre-program 2 (2 cups): 100 ml approximately

Programming 1 espresso cup

To pre-program the preparation of 1 espresso cup to your taste, follow the steps for preparing an espresso

(See section "Espresso function" page 18).

n Place the cup on the cup rest grill.

n When the TEMPERATURE light (h6) stops flashing, briefly press the Pre-programmed 1 espresso

button to the right and hold in this position. The espresso begins to dispense.

n When the desired volume of espresso is reached, release the button. The dispensing of coffee is

stopped immediately and the personalized setting is stored in the memory.

Programming 2 cups of espresso

The steps are identical to those for programming 1 cup. Simply place 2 cups on the cup rest grill and

activate the Pre-programmed 2 cup espresso button rather than the Pre-programmed 1 cup button.

IMPORTANT

The maximum volume that can be programmed for 1 cup is 150 ml; for 2 cups it is 250 ml

approximately.

n The programmed settings can be changed at any time by following the same procedure.

IMPORTANT

You can serve yourself from the espresso machine manually by interrupting the dispensing of coffee

at any time. To do so, briefly activate the espresso button or or the previously activated

button.

2. HOT WATER FUNCTION

The production of hot water is ideal for preparing tea, infusions or pre-heating a container.

n Check the water level in the tank.

n Make sure that the frothing nozzle is securely fitted to the adjustable spout.

n Check that the rotating control button is set to PENDING (

●) Fig.4) and that the TEMPERATURE

SELECTION button (h5) is at ESPRESSO/HOT WATER .

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page17

n Switch the machine on by turning the START/STOP (h7) button to the right to the (I) setting.

n The TEMPERATURE light (h6) flashes.

n Wait until the TEMPERATURE light (h6) stops flashing.

n Place a cup or bowl under the adjustable spout and make sure it is correctly positioned.

n Turn the control button to HOT WATER . The hot water flows through the spout.

n When the required quantity of water is reached, turn the rotating control button to PENDING (

●) to

stop the flow of hot water (Fig.4).

n The pump stops immediately and the spout circuit is closed.

IMPORTANT

It is possible that some steam may be released from the water tank. This is completely normal.

n You can now use the water collected to prepare your hot drink.

3. STEAM FUNCTION

Steam production is ideal for making the milk froth used in milk drinks (cappuccino, latte machiatto, hot

chocolate, etc.).

n Check the water level in the tank.

n Make sure that the frothing nozzle is securely fitted to the adjustable spout.

n Check that the rotating control button is set to PENDING (

●).

n Switch the machine on by turning the START/STOP (h7) button to the right to the (I) setting.

n The TEMPERATURE light (h6) flashes.

IMPORTANT

If the rotating control button (d) is not at PENDING (

●), the TEMPERATURE light (h6) flashes

quickly and heating does not occur.

n Turn the TEMPERATURE SELECTION button (h5) to STEAM .

n Wait until the TEMPERATURE light (h6) stops flashing.

n Place a container or empty cup under the spout.

n Open the spout circuit by turning the control button to STEAM release any remaining water that

may be in the circuit.

n Turn the control button back to the left to PENDING (

●).

n Pour the milk into a container and plunge the frothing spout into the container without touching the

bottom to pevent blocking the steam flow.

Advice

For a better result, use refrigerated milk, a cold stainless steel container and measure approximately

20 to 30 ml of milk per drink.

n Wait until the TEMPERATURE light (h6) stops flashing.

n Turn the control button back to STEAM .

IMPORTANT

You will then hear an intermittent noise which is the pump jump starting. This is completely normal

and necessary for the steam production. A little steam may be released from the water tank. This

is completely normal.

IMPORTANT

To prevent blocking the flow of steam, the spout should not touch the bottom of the container.

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page18

n As soon as the milk begins to move, slowly return the frothing spout back to the surface with a circular

motion. Plunge the spout into the container again this time with an increasing circular movement.

n Do this several times until the milk turns into a thick and creamy froth.

n When the required quantity of milk is reached, close the spout circuit by turning the control button to

PENDING (

●).

n You can now remove the container from the spout.

Important

- Following the production of steam, the spout and its frothing nozzle are

extremely hot. Be careful of the risk of accidental burns.

- It is strongly recommended that the spout and its frothing nozzle is cleaned

every time milky froth is made (See section "Cleaning and maintenance"

page 20). This operation prevents any risk of spreading micro bacteria.

Important

To change to the ESPRESSO function after the production of steam, it is

imperative that hot water is passesd through the spout (See "Hot water

function" page 17) to force the temperature of the thermo block to fall. The

ESPRESSO function will remain blocked if this operation is not performed

first.

4. DESCALING

Reminder: The guarantee does not cover faulty appliances on which descaling was not performed

regularly.

Important

If you use your machine on almost a daily basis, regular descaling of the different

water circuits is recommended on average every 2 months

Descaling of the ESPRESSO circuit

This operation is performed with the filter holder removed.

n Empty the water tank completely.

n Pour 500 ml of water into the tank with a sachet of “Special espresso” anti-scale agent available in

stores or 250 ml of white vinegar mixed with 250 ml of water.

n Place a large container under the dispensing unit.

n Turn the appliance on and check that the rotating control button is set to PENDING (

●) (Fig.4) and

that the TEMPERATURE SELECTION button (h5) is at ESPRESSO/HOT WATER . Wait until

the TEMPERATURE light (h6) stops flashing.

a) Activate the pump using the Pre-programmed 1 cup espresso button or the Pre-programmed

2 cup button to dispense approximately 50 ml in the container then stop the pump by

releasing the button used.

Important

By doing this, the personal setting for the volume of espresso linked to the

button used is changed.

Remember to reset this when you next make a espresso.

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page19

b) Immediately turn the START/STOP (h7) button to "●" to switch off the machine (this must be

done before the suction noise for draining is triggered).

c) Let the solution rest for approximately 10 minutes in the case of the anti-scale agent (and 20

minutes for the vinegar mixture) to let the liquid act in the heating unit and at the entrance to the

dispensing unit.

n Repeat steps a) to c) twice.

Descaling of the SPOUT circuit

The descaling of the SPOUT circuit is very similar to that of the ESPRESSO circuit.

n Place the container under the adjustable spout and position correctly.

n Turn the appliance on and check that the rotating control button is set to PENDING (

●) and that the

TEMPERATURE SELECTION button (h5) is at EXPRESSO/HOT WATER .

n Wait until the TEMPERATURE light (h6) stops flashing.

n Turn the rotating control button to the right to select the HOT WATER function " .

n Let the antiscale agent flow through the spout for a maximum of 20 seconds.

n Stop the flow by turning the rotating control button to PENDING (

●).

n Immediately switch off the machine by turning the START/STOP (h7) button to

●.

n Let the solution rest for the same length of time as for the ESPRESSO circuit.

n During this time, remove the remainder of the anti-scale agent contained in the tank and rinse thoroughly

with fresh water.

Rinsing of circuits

n Fill the tank with fresh water up to the maximum water level.

n Turn the machine on and wait until the TEMPERATURE light (h6) stops flashing.

n Get a large container to collect the water.

n Start rinsing by circulating a full tank of fresh water as follows:

- 3/4 of the tank through the ESPRESSO circuit

- 1/4 of the tank through the SPOUT circuit

IMPORTANT

Once you have let the equivalent of a tank of fresh water circulate through the 2 circuits you can

be sure that there is no anti-scale agent left in the tank nor any residue taste resulting from its use.

5. CLEANING AND MAINTENANCE

To ensure that your Dual Espresso-Filter Coffee Machine works for many years, we advise that you perform

regular maintenance.

Important

- Before any cleaning, disconnect the machine’s power cord and ensure that the

machine is cold.

- None of the machine’s parts can be put in the dishwasher.

Regular cleaning of filters and filter holder

n After each use, clean the filter and the filter holder opening under warm water.

n Regularly check that the sieves at the bottom of the filters are not blocked. If necessary, use a fine

needle (not supplied) to unblock the holes. You can also wipe the upper surface of the sieves using a

synthetic brush and run the filters under warm water to remove any dirt.

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page20

Clean the filters thoroughly

If you notice a problem dispensing coffee, it may be that the filter is blocked. In this case, clean thoroughly

n Using a cross recess unscrew the central screw.

n Remove the stainless steel sieve.

n Clean all the parts in warm water.

n Hold to the light to check that there is no residue blocking the holes. If so, clean more thoroughly taking

care to remove any particles using a synthetic brush or a fine needle .

Important

Ensure that the different parts are dry before assembling: place the sieve in

the filter and tighten the screw.

Cleaning the dispensing unit

n The base of the dispensing unit must be cleaned regularly using a non-abrasive cloth soaked in water.

This is to remove all remaining coffee grounds from the sieve and in the filter holder housing system.

n Residual coffee grounds can also get blocked in the dispensing unit’s peripheral cylinder. In this case,

this can be removed using a small fine object which is not pointed or a toothpick.

IMPORTANT

You are advised to operate your machine regularly with the filter holder in place but without coffee,

to remove any coffee remains.

Cleaning the adjustable spout and frothing nozzle

It is highy recommended that you clean the spout and its frothing nozzle after each production of milk froth

Important

Ensure that the spout and its nozzle have cooled down before performing any

maintenance.

n Remove the frothing nozzle from the spout by turning fully then pull the part to release (Fig.17).

n Dip the frothing nozzle in very hot water and ensure that any milk residue is completely removed.

IMPORTANT

If any of the milk froth has dried up around the frothing nozzle, dip this in a container of water

overnight to soften the residue

n Clean the outside of the plastic tube of the nozzle with hot water.

n If necessary, unblock the internal steam duct by inserting the needle supplied (u) into the nozzle hole and

running some hot water or steam through the plastic tube (See sections "Hot water function" page 17

or "Steam function" page 20).

n Ensure that all parts are completely dry.

n We also recommend that you use this needle to unblock the holes in the filters and the small hole at

the top of the detachable metal steam foam nozzle (fig 18).

n Carefully fit the special cappuccino nozzle by positioning the pins in the holes and rotating them anti-

clockwise until they lock into place (Fig.19).

IMPORTANT

These operations are essential to prevent any risk of spreading micro bacteria.

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page21

Cleaning the water tank

n Remove and clean the water tank every day. Rinse with clear water and re-position correctly ensuring

that it is correctly lodged in its housing.

n If a layer of limescale should form on the tank walls, descale using a mixture of water and white vinegar.

Let the mixture rest for 1 hour.

n Wipe with a non-abrasive sponge and rinse thoroughly.

Cleaning the cup rest grill

n Remove the cup rest grill by moving it upwards.

n Wash with warm soapy water.

n Rinse and dry carefully.

Cleaning the water drip tray

n Remove the water drip tray by sliding it forwards (fig.20).

n Dismantle the water drip tray:

n Press the 2 height adjustment buttons at the same time.

n Remove the cup rest grill (Fig.21).

n To release the tray hold the 2 plastic rods serving as a support at the front and rear center of the tray.

Clean under warm water and dry thoroughly.

IMPORTANT

The water level indicator can be removed and re-attached using the clips.

n Clean the stainless steel cover using a non-abrasive slightly damp cloth. Dry. Do not allow water to get

into the adjustment buttons’ mechanisms.

n Re-assemble the tray by simply applying pressure on the plastic clips in the positions specified for this

purpose.

n Reposition the cup rest grill.

n Place the tray in the lower position by fully pressing down the 2 adjustment buttons at the same time.

Cleaning the appliance body, the cup warming plate

These parts of the appliance are cleaned using a non-abrasive and slightly wet cloth.

Important

Take care not to allow water on the control panel.

Any other servicing should be performed by an authorized service representative.

COFFEE

1. COFFEE PREPARATION

n Open the COFFEE lid by pressing both sides and open the lid to 90° without forcing (Fig.5 and 6).

n Pour the quantity of water required into the tank depending on the number of cups required, never

exceeding the MAX marking located at the overflow opening (Fig.7 and 8).

IMPORTANT

- For a better taste, use only fresh water.

- Measure between 100 and 150 ml per cup of coffee.

English

KR_ESPRESSO-COMBI_XP6040_NAFTA_NC00023128-03 20/01/12 14:46 Page22

La page charge ...

Krups XP604050 Manuel utilisateur

Marque: Krups

Modèle: XP604050

Catégorie: Cafetières

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Krups XP604050 User manual
español: Krups XP604050 Manual de usuario

Krups XP604050 Manuel utilisateur

Krups XP604050 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents