Wacker Neuson LTV4K Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur

Ce manuel convient également à

LTV4K, LTV6K
LTV6L, LTV8K
Type LTV4K, LTV6K, LTV6L, LTV8K
Document
5100030418
Date
319
Revision 05
Language
EN-FR
Operator’s Manual
Notice d'emploi
Light Tower
Tour d’éclairage
Copyright notice
© Copyright 2019 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original instructions
This Operator’s Manual presents the original instructions. The original
language of this Operator’s Manual is American English.
wc_tx004643en.fm 3
CALIFORNIA Proposition 65 Warning
CALIFORNIA Proposition 65 Warning
WARNING
The engine exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
WARNING
Diesel engine exhaust and some of its constituents are known to the State of
California to cause cancer, birth defects, and other reproductive harm.
WARNING
Cancer and Reproductive Harm -
www.P65Warnings.ca.gov.
WARNING
Batteries, battery posts, terminals and related accessories contain lead and lead
compounds, and other chemicals known to the State of California to cause cancer
and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.
CALIFORNIA Proposition 65 Warning Proposition 65 Warning
4 wc_tx004643en.fm
Notes
wc_tx004428en.fm
5
LTV Forward
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
For spare parts information, please see your Wacker Neuson Dealer, or visit the
Wacker Neuson website at http://www.wackerneuson.com/.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change any
portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
wc_gr013759
215429215429
R
51000314545100031454
For electrical
equipment only.
Pour material
electrique seulement.
lbs
Item No.
Type/Model
Serial No.
Rev.
MAX AMB 40~C
RPMhz
MON/YR
MADE IN USA
kW
kg
V
n
A
P. F .
Serial Number:
wc_tx004428en.fm
6
Forward LTV
Manufacturer’s
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following
consequences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
CALIFORNIA
Proposition
65 Warning
Combustion exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental
discharge of sparks or flames from the engine exhaust. Spark arresters are
qualified and rated by the United States Forest Service for this purpose. In order to
comply with local laws regarding spark arresters, consult the engine distributor or
the local Health and Safety Administrator.
Abbreviations
Abb. or
Acronym
Definition
Abb. or
Acronym
Definition
CARB California air resource board LTV Light tower verticle
CDL Commercial driver’s License NATM National association of trailer manufacturers
CO Carbon monoxide NHTSA National highway traffic safety administration
EPA Environmental protection agency PPE Personal protective equipment
GFCI Ground fault current interrupter S/N Serial number
LED Light emitting diode VIN Vehicle identification number
Table of Contents
LTV
wc_bo5100030216_05TOC.fm
7
CALIFORNIA Proposition 65 Warning 3
Foreword 5
1 Safety Information 13
1.1 Signal Words Used in this Manual ................................................................13
1.2 Machine Description and Intended Use ........................................................13
1.3 Operating Safety ...........................................................................................15
1.4 Metal Halide Lamp Safety .............................................................................17
1.5 Service Safety ...............................................................................................17
1.6 Operator Safety while Using Internal Combustion Engines ..........................19
1.7 Safety Guidelines for Lifting the Machine .....................................................20
1.8 Safety Guidelines for Towing the Machine ...................................................20
1.9 Reporting Safety Defects ..............................................................................21
2 Labels 22
2.1 Label Locations .............................................................................................22
2.2 Label Meanings ............................................................................................24
3 Lifting and Transporting 32
3.1 Lifting the Machine ........................................................................................32
3.2 Preparing the Machine for Transport on a Truck or Trailer ...........................33
3.3 Before Towing Checklist ...............................................................................34
3.4 Towing the Machine ......................................................................................35
3.5 Trailer ............................................................................................................36
3.6 Flip-up Tongue ..............................................................................................37
4 Machine Setup 38
4.1 Preparing the Machine for First Use .............................................................38
4.2 Positioning the Machine ................................................................................39
4.3 Ground Connection .......................................................................................40
4.4 Leveling the Trailer—Vertical Mast Light Towers .........................................41
4.5 Refueling the Machine ..................................................................................42
4.6 Aiming the Lights—Vertical Mast Light Towers ............................................43
4.7 Manually Rotating the Light Bar ....................................................................45
4.8 Raising the Tower—Manual Winch System .................................................46
4.9 Lowering the Tower—Manual Winch System ...............................................48
Table of Contents
LTV
wc_bo5100030216_05TOC.fm
8
4.10 Raising the Tower—Power Winch System ...................................................49
4.11 Lowering the Tower—Power Winch System ................................................51
5 Operation 54
5.1 Generator Derating .......................................................................................54
5.2 Control Panels and Receptacles—KUBOTA ................................................54
5.3 Control Panels and Receptacles—KOHLER ................................................55
5.4 Control Panel and Receptacles—DeepSea ..................................................56
5.5 Machine Monitoring—DeepSea ....................................................................57
5.6 Alarms and Shut-Down Conditions—DeepSea ............................................59
5.7 Resetting the Maintenance Timers—DeepSea ............................................60
5.8 Before Starting ..............................................................................................61
5.9 Starting, Operating, Stopping the Machine—KUBOTA ................................62
5.10 Starting, Operating, and Stopping the Machine—KOHLER .........................64
5.11 Starting, Operating, Stopping the Machine—DeepSea ................................66
5.12 Auto Mode (Remote Run) .............................................................................68
5.13 Engine—Jump-Starting .................................................................................71
5.14 Emergency Shutdown Procedure .................................................................73
5.15 Using the Convenience Receptacles—50 Hz and 60 Hz .............................74
6 Factory-Installed Options 76
6.1 Cold Weather Package .................................................................................76
6.2 Engine Block Heater .....................................................................................76
6.3 Battery Blanket .............................................................................................77
6.4 Oil Pan Heater ..............................................................................................77
6.5 Fuel and Water Separator ............................................................................78
6.6 Positive Air Shutoff .......................................................................................78
6.7 Shore Power .................................................................................................78
6.8 Containment System Float Switch ................................................................79
6.9 LED Lights ....................................................................................................79
7 General Maintenance 80
7.1 Preparing for Maintenance ...........................................................................80
7.2 Periodic Maintenance Schedule ...................................................................81
7.3 Cleaning the Machine ...................................................................................81
7.4 Inspecting the Machine .................................................................................82
7.5 Maintaining the Trailer ..................................................................................82
7.6 Maintaining the Battery .................................................................................83
7.7 Removing and Replacing Lamps ..................................................................84
Table of Contents
LTV
wc_bo5100030216_05TOC.fm
9
7.8 Checking and Draining the Containment System (if equipped) ................... 86
7.9 Long-Term Storage ...................................................................................... 87
7.10 Machine Disposal and Decommissioning .................................................... 88
8 Engine Maintenance: KUBOTA D1005 / D1105 89
9 Engine Maintenance: KUBOTA Z482 91
10 Engine Maintenance: KOHLER 1003 93
11 Troubleshooting 95
12 Technical Data 97
12.1 Engine—KUBOTA ....................................................................................... 97
12.2 Engine—KOHLER ....................................................................................... 98
12.3 Generator ..................................................................................................... 99
12.4 Machine ..................................................................................................... 100
12.5 Radiation Compliance ................................................................................ 101
12.6 Dimensions—LTV4K, LTV6K, LTV8K, LTV6L ........................................... 101
12.7 Dimensions—Skidded LTV6K, LTV8K, LTV6L .......................................... 101
13 Emissions Control Systems Information and Warranty: KUBOTA 102
13.1 Emission Control System Background Information .................................... 102
13.2 Limited Defect Warranty for Wacker Neuson Emission Control
Systems ..................................................................................................... 103
14 Emissions Control Systems Information and Warranty: KOHLER 106
14.1 Emission Control System Background Information .................................... 106
14.2 Limited Defect Warranty for Exhaust Emission Control System ................ 106
15 Schematics 107
15.1 LTV—Photo Sensor ................................................................................... 107
15.2 Components ............................................................................................... 107
15.3 LTV—Controller-Kubota Z482 ................................................................... 108
15.4 Components ............................................................................................... 109
15.5 LTV—Base Schematic ............................................................................... 110
15.6 Components ............................................................................................... 111
Table of Contents
LTV
wc_bo5100030216_05TOC.fm
10
15.7 LTV—Metal Halide Lights Module ............................................................. 112
15.8 Components ............................................................................................... 112
15.9 LTV—120V / 30A Receptacle Module ....................................................... 113
15.10 Components ............................................................................................... 113
15.11 LTV—8 kW GFCI Receptacle Module ....................................................... 114
15.12 Components ............................................................................................... 114
15.13 LTV—Trailer ............................................................................................... 115
15.14 Components ............................................................................................... 115
15.15 LTV—Kubota Engine ................................................................................. 116
15.16 Components ............................................................................................... 117
15.17 LTV—Power Winch .................................................................................... 118
15.18 Components ............................................................................................... 118
15.19 LTV—LED Lights Module .......................................................................... 119
15.20 Components .............................................................................................. 119
15.21 LTV—Auto Start Module ............................................................................ 120
15.22 Components ............................................................................................... 120
15.23 LTV—Shore Power Module ....................................................................... 121
15.24 Components ............................................................................................... 121
15.25 LTV—Controller-Kubota D2005 / D1105 ................................................... 122
15.26 Components ............................................................................................... 123
15.27 LTV—230V / 50 HZ Module ....................................................................... 124
15.28 Components ............................................................................................... 124
15.29 LTV—Containment Switch ......................................................................... 125
15.30 Components ............................................................................................... 125
15.31 LTV—URI Telematics ................................................................................ 126
15.32 Components ............................................................................................... 126
16 Appendix I 127
16.1 Standard Racked Assembly ....................................................................... 127
16.2 Installing the Axle ....................................................................................... 128
16.3 Installing the Fenders ................................................................................. 129
16.4 Installing the Wheels .................................................................................. 130
16.5 Installing the Outriggers and Swivel Jacks ................................................ 131
16.6 Installing the Tongue Assembly ................................................................. 132
16.7 Installing the Mast ...................................................................................... 134
16.8 Installing the Standard Winch .................................................................... 135
16.9 Installing the Power Winch ......................................................................... 137
16.10 Installing the Light Support Bracket and Light Bar ..................................... 139
16.11 Installing the Lights—240W Metal Halide or 300W LED ............................ 140
16.12 Installing the Lights—240W LED ............................................................... 141
16.13 Connecting the Wiring at the Junction Box ................................................ 142
wc_si000704en.fm
13
LTV Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
1.2 Machine Description and Intended Use
Machine
description
This machine is a mobile, trailer-mounted light tower. The Wacker Neuson Light
Tower consists of a trailer with a cabinet containing a diesel engine, a fuel tank, a
control panel, and an electric alternator. A telescoping tower with four metal halide
or LED lights is vertically mounted to the top of the cabinet. As the engine runs, the
generator converts mechanical energy into electric power. The metal halide or LED
lights run off this power. Receptacle(s) are also provided to power auxiliary loads.
The operator uses the control panel to operate and monitor the machine.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si000704en.fm
14
Safety Information LTV
Intended use
This machine is intended for the illumination of outdoor areas. This machine is also
intended for the purpose of supplying electrical power to connected loads. Refer to
the machine specifications for the output voltage and frequency, and for the
maximum output power limit of this machine.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty. The following are some
examples of misuse:
Connecting a load that has voltage and frequency requirements that are
incompatible with the machine output
Overloading the machine with a device that draws excessive power during
either continuous running or start-up
Operating the machine in a manner that is inconsistent with all federal, state,
and local codes and regulations
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Using the machine to tow other machines (unless factory equipped)
Using the machine as a hoist, or hanging items from the tower
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, exhaust, and carbon monoxide from the engine
Heat from the lights
Ultraviolet radiation from the lights
Fire hazards from improper refueling techniques
Fuel and its fumes
Electric shock and arc flash
Personal injury from improper lifting the trailer tongue
Glare from lights (lights may blind drivers of nearby motor vehicles if the lights
are incorrectly positioned)
Typical hazards related to towing a trailer on roads and highways
To protect yourself and others, make sure you thoroughly read and understand
the safety information presented in this manual before operating the machine.
wc_si000704en.fm
15
LTV Safety Information
1.3 Operating Safety
Operator
training
Before operating the machine:
Read and understand the operating instructions contained in all manuals
delivered with the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Contact Wacker Neuson for additional training if necessary.
When operating this machine:
Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
Have received instruction on how to properly use the machine
Are familiar with required safety devices
The machine must not be accessed or operated by:
Children
People impaired by alcohol, drugs, or prescription drugs
Application
area
Be aware of the application area.
Keep unauthorized personnel, children, and pets away from the machine.
Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
Identify whether special hazards exist in the application area, such as toxic
gases or unstable ground conditions, and take appropriate action to eliminate
the special hazards before using the machine.
Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
vt
Safety
devices,
controls, and
attachments
Only operate the machine when:
All safety devices and guards are in place and in working order.
All controls operate correctly.
The machine is set up correctly according to the instructions in the Operator’s
Manual.
The machine is clean.
The machine’s labels are legible.
To ensure safe operation of the machine:
Do not operate the machine if any safety devices or guards are missing or
inoperative.
Do not modify or defeat the safety devices.
Only use accessories or attachments that are approved by Wacker Neuson.
wc_si000704en.fm
16
Safety Information LTV
Safe
operating
practices
When operating this machine:
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
Do not operate a machine in need of repair.
Do not consume the operating fluids used in this machine. Depending on your
machine model, these operating fluids may include water, wetting agents, fuel
(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic oil,
heat transfer fluid (propylene glycol with additives), battery acid, or grease.
Personal
protective
equipment
(PPE)
Wear the following personal protective equipment (PPE) while operating this
machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
Before
starting
Be sure the machine is on a firm, level surface and will not tip, roll, slide, or fall
while operating.
Never connect the machine to other power sources, such as supply mains of
power companies.
Never use the machine if the insulation on the electrical cord is cut or worn
through.
Never raise the tower or operate the machine in high winds.
The tower extends up to 7 m (23 ft). Make sure the area above the trailer is
open and clear of overhead wires and obstructions.
Operation
Keep the area under and around the lights clear of people while raising and
lowering the tower.
Do not move the machine while it is operating or while the tower is raised.
After use
Stop the engine when the machine is not being operated.
Close the fuel valve on engines equipped with one when the machine is not
being operated.
Ensure that the machine will not tip over, roll, slide, or fall when not being
operated.
Store the machine properly when it is not being used. The machine should be
stored in a clean location out of the reach of children.
Lower the tower when not in use, or if high winds or electrical storms are
expected in the area.
The lamps become extremely hot during use! Allow the lamp and fixture to cool
10–15 minutes before handling.
wc_si000704en.fm
17
LTV Safety Information
1.4 Metal Halide Lamp Safety
Description
The lamps provided with the machine are electric discharge lamps. They are
designed for use with metal halide ballasts only, and require time to reach full
brightness on initial startup and after a power interruption. These lamps comply
with FDA regulation performance standards 21 CFR 1040-30.
Operating
safety
Replace damaged lamps according to the instructions in section Removing and
Replacing Lamps.
1.5 Service Safety
Service
training
Before servicing or maintaining the machine:
Read and understand the instructions contained in all manuals delivered with
the machine.
Familiarize yourself with the location and proper use of all controls and
protective devices.
Only trained personnel shall troubleshoot or repair problems occurring with the
machine.
Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
Do not allow untrained or improperly trained people to service or maintain the
machine. Personnel servicing or maintaining the machine must be familiar with
the associated potential risks and hazards.
Precautions
When servicing or maintaining the machine:
Read and understand the service procedures before performing any service to
the machine.
All adjustments and repairs must be completed before operating the machine.
Do not operate the machine with a known problem or deficiency.
All repairs and adjustments shall be completed by a qualified technician.
Turn off the machine before performing maintenance or making repairs.
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
Reinstall the safety devices and guards after repair and maintenance
procedures are complete.
WARNING
Personal injury hazard. Broken or punctured lamps can cause serious skin burns
and eye inflammation from shortwave ultraviolet radiation.
Do not operate the machine if a lamp is damaged.
Replace damaged lamps immediately.
wc_si000704en.fm
18
Safety Information LTV
Before servicing the machine, make sure the engine start switch is turned to the
OFF position, the circuit breakers are open (off), and the negative terminal on
battery is disconnected. Do not perform even routine service (oil/filter changes,
cleaning, etc.) unless all electrical components are shut down.
Always turn off light circuit breakers and shut down engine before disconnecting
light fixtures or changing light bulbs.
Machine
modifications
When servicing or maintaining the machine:
Use only accessories/attachments that are approved by Wacker Neuson.
Do not defeat safety devices.
Do not modify the machine without the express written approval of Wacker
Neuson.
Replacing
parts and
labels
Replace worn or damaged components.
Replace all missing and hard-to-read labels.
When replacing electrical components, use components that are identical in
rating and performance to the original components.
When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.
Cleaning
When cleaning and servicing the machine:
Keep machine clean and free of debris such as leaves, paper, cartons, etc.
Keep labels legible.
Do not clean the machine while it is running.
Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.
Personal
protective
equipment
(PPE)
Wear the following personal protective equipment (PPE) while servicing or
maintaining this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair.
Remove all jewelry (including rings).
wc_si000704en.fm
19
LTV Safety Information
1.6 Operator Safety while Using Internal Combustion Engines
Operating
safety
When running the engine:
Keep the area around the exhaust pipe free of flammable materials.
Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine. Do not run the machine if fuel leaks are present or the fuel lines are
loose.
Do not smoke while operating the machine.
Do not run the engine near sparks or open flames.
Do not touch the engine or muffler while the engine is running or immediately
after it has been turned off.
Do not operate a machine when its fuel cap is loose or missing.
Do not start the engine if fuel has spilled or a fuel odor is present. Move the
machine away from the spill and wipe the machine dry before starting.
Do not use the machine in areas with risk of explosion or fire.
Refueling
safety
When refueling the engine:
Clean up any spilled fuel immediately.
Refill the fuel tank in a well-ventilated area.
Reinstall the fuel tank cap after refueling.
Use tools specifically meant for refueling (for example, a fuel hose or funnel).
Do not smoke.
Do not refuel a hot or running engine.
Do not refuel the engine near sparks or open flames.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Exhaust gas from the engine contains carbon monoxide, a deadly poison.
Exposure to carbon monoxide can kill you in minutes.
NEVER operate the machine inside an enclosed area, such as a tunnel, unless
adequate ventilation is provided through items such as exhaust fans or hoses.
wc_si000704en.fm
20
Safety Information LTV
1.7 Safety Guidelines for Lifting the Machine
When lifting the machine:
Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any
other type of lifting device used is attached securely and has enough weight-
bearing capacity to lift or hold the machine safely. See the Technical Data
chapter for machine weight.
Remain aware of the location of other people when lifting the machine.
Only use the lifting points and tie-downs described in the Operator’s Manual.
Make sure the transporting vehicle has sufficient load capacity and platform size
to safely transport the machine.
To reduce the possibility of injury:
Do not stand under the machine while it is being lifted or moved.
Do not get onto the machine while it is being lifted or moved.
1.8 Safety Guidelines for Towing the Machine
When towing the machine:
Do not tow the machine if the towing vehicle’s hitch or the trailer’s coupler are
damaged.
Do not tow the machine if safety chains are damaged.
Do not tow the machine if any of the trailers lug nuts are loose or missing.
Do not tow the machine if the trailers tires have less than 1/16 inch (1.5 mm) of
tread.
Do not tow the machine if trailer tires are underinflated.
Do not tow the machine unless the trailer’s brakes are functioning properly.
Do not tow the machine if trailer lighting is not functioning properly.
Do not exceed the trailer manufacturers speed limitations of 89 km/h (55 mph).
When towing the machine:
Only tow the machine when the trailer’s lug nuts are properly torqued.
Only tow the machine when the trailer’s tires are properly inflated.
Only tow the machine when all trailer lights are functioning correctly.
Only tow the machine when the trailer’s safety chains are connected to the
towing vehicle in a crisscross pattern.
Maintain extra distance between the towing vehicle and other vehicles.
Avoid soft shoulders, curbs, and sudden lane changes.
Abide by all licensing requirements for your area.
WARNING
Risk of severe injury or death. Improper trailer condition and towing technique can
lead to an accident.
Obey the instructions below to reduce the risk of an accident.
wc_si000704en.fm
21
LTV Safety Information
If you have not driven a towing vehicle with a trailer before, practice turning,
stopping, and backing up the towing vehicle with the trailer in an area away from
traffic. Only drive the towing vehicle with the trailer when you are confident in your
ability to do so.
1.9 Reporting Safety Defects
If you believe your trailer has a defect which could cause a crash or could cause
injury or death, you should immediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifying Wacker Neuson.
If NHTSA receives similar complaints, it may open an investigation; and if it finds
that a safety defect exists in a group of trailers, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in individual problems
between you, your dealer, or Wacker Neuson.
To contact NHTSA, you may either contact the Vehicle Safety Hotline toll-free at
1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to:
Administrator
NHTSA
1200 New Jersey Avenue S.E.
Washington, DC 20590
You can also obtain other information about your motor vehicle safety from
http://www.safercar.gov
wc_si001039en.fm
22
Labels LTV
2 Labels
2.1 Label Locations
wc_gr013742
a
b
c
d
g
j
k
m
n
h
o
p
q
e,
f
e,
f
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304

Wacker Neuson LTV4K Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues