Danby DPA085B1GB Le manuel du propriétaire
- Catégorie
- Climatiseurs mobiles
- Taper
- Le manuel du propriétaire
Danby Products Limited, Ontario, Canada N1H 6Z9
Danby Products Inc., Findlay, Ohio, USA 45840
-ODELs-ODÕLEs-ODELO
11.03.14
OWNER’S USE AND CARE GUIDE
GUIDE D’UTILISATION ET D’ENTRETIEN
PORTABLE AIR CONDITIONER
CLIMATISEUR PORTATIF
MODEL MODÈLE DPA085B1GB
TO OBTAIN WARRANTY SERVICE YOU MUST PROVIDE A VALID PROOF OF
PURCHASE. PLEASE STAPLE YOUR RECEIPT TO THIS PAGE FOR FUTURE
REFERENCE.
-------------------------------------------------------------------------------------------------------------------
POUR OBTENIR LE SERVICE SUR GARANTIE VOUS DEVEZ FOURNIR UNE
PREUVE D’ACHAT VALIDE. VEUILLEZ AGRAFER VOTRE REÇU À CETTE PAGE
POUR RÉFÉRENCE FUTURE.
-------------------------------------------------------------------------------------------------------------------
This product is factory equipped with a power supply cord that has a three-pronged grounded plug. It must
be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and
applicable local codes and ordinances. If the circuit does not have a grounding type receptacle, it is the
responsibility and obligation of the customer to exchange the existing receptacle in accordance with the
National Electrical Code and applicable local codes and ordinances. The third ground prong should not,
under any circumstances, be cut or removed. Never use the cord, the plug or the appliance when they show
any sign of damage. Do not use your appliance with an extension cord unless it has been checked and test-
ed by a quali¿ ed electrician or electrical supplier.
IMPORTANT - GROUNDING METHOD
Ce produit arrive d’origine avec un cordon d’alimentation équipé d’une prise à trois ¿ ches. Il doit être
branché dans une prise avec une ¿ che de mise à la terre en conformité avec le Code national de l’électricité
et les codes et règles locaux applicables. Si la prise murale n’a pas de mise à la terre, il est de la
responsabilité et l’obligation du client de changer la prise existante pour la rendre conforme au Code
national de l’électricité et aux codes et règles locaux applicables. La ¿ che de mise à la terre ne doit pas, en
aucune circonstance, être coupée ou retirée. Si vous apercevez des signes de dommage, n’utilisez jamais le
cordon d’alimentation, la prise ou l’appareil. N’utilisez jamais l’appareil avec une rallonge sauf si elle a été
véri¿ ée et testée par un électricien quali¿ é ou un fournisseur de matériel électrique.
IMPORTANT - MÉTHODE POUR LA MISE À LA TERRE
PORTABLE AIR CONDITIONER
Owner’s Use and Care Guide
Welcome .............................................................
Safety Instructions ..............................................
Identifying Parts ..................................................
Features ..............................................................
Operating Instructions .........................................
Installation Instructions .......................................
Care and maintenance ........................................
Troubleshooting ...................................................
Warranty ..............................................................
CLIMATISEUR PORTATIF
Guide d’utiliser et soin de propriètaire
Bienvenue ...........................................................
Consignes de sécurité importantes .....................
L'Identification des pièces ....................................
Caractéristiques ..................................................
Consignes d’utilisation ........................................
Instructions d’installation .....................................
Soins et entretien ................................................
Dépannage .........................................................
Garantie ..............................................................
Contents
2
3-4
4-6
6-7
8-9
10-14
15
16
17
18
19-20
21-22
23
24-25
26-30
31
32
33
CAUTION:
PRECAUTION:
Read and follow all safety rules and
operating instructions before first use of this
product.
Veuillez lire attentivement les consignes de
sécurité et les instructions d’utilisation avant
l’utilisation initiale de ce produit.
Model Modèle
DPA085B1GB
1
Table de matières
Welcome
2
Welcome to the Danby family. We are proud of our quality products, and we believe in dependable service, like you will
¿ nd in this Owner’s Use and Care Guide, and like you will receive from our friendly customer service department. Best of
all, you will experience these values each and every time you use your Danby appliance. That is important, because your
new appliance will be a part of your family for a long time.
Note the information below; you will need this information to obtain service under warranty.
To receive service, you must provide the original receipt.
Model No:
Serial No:
Date Purchased:
NEED HELP?
Before you call for service, here are a few things you can do to
help us serve you better:
Read this Owner’s Use and Care Guide:
It contains instructions to help you use and maintain your
appliance properly.
If you received a damaged appliance:
Immediately contact the retailer (or builder) that sold you the
appliance.
Save time and money:
Check the Troubleshooting section at the end of the guide
before calling. This section helps you solve common problems
that may occur.
If you do need service, you can relax, knowing help is only a
phone call away.
Tel: 1-800-26-
(1-800-263-2629)
WARNING
Improper connection of the grounding plug can result in risk of
¿ re, electric shock and/or injury to persons associated with the
appliance. Check with a quali¿ ed service representative if in doubt
that the appliance is properly grounded.
Important Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
SAFETY
PRECAUTIONS
To prevent injury to the user or other people and property damage, the following instructions must be followed.
Incorrect operation resulting from to ignoring these instructions may cause harm or damage.
Your air conditioner should be used in such a way that it is protected
from moisture. e.g. condensation, splashed water, etc. Do not place or
store your air conditioner where it can fall or be pulled into water or
any other liquid. Unplug unit immediately if this occurs.
Always transport your air conditioner in a vertical position and place
on a stable, level surface during use.If the unit is transported laying
on it’s side it should be stood up and left unplugged for 4 hrs.
Turn off the unit when not in use.
Always contact a qualified person to perform repairs. If the power cord
is damaged it must be repaired by a qualified technician.
Keep clearance of at least 30cm (1 foot) all around the unit from walls,
furniture and curtains, to allow for adequate air flow.
If the air conditioner is knocked over during use, turn off the unit and
unplug it immediately.
Always use the switch on the control panel to turn the unit on or off.
ALWAYS DO THIS
Do not operate your air conditioner in a wet room such as a bathroom
or laundry room.
Do not touch the unit with wet or damp hands.
Do not press the buttons on the control panel with anything other than
your fingers.
Do not remove any fixed components. Never use this appliance if it is
not working properly, or if it has been dropped or damaged.
Never use the plug to start and stop the unit.
Do not cover or obstruct the inlet or outlet grilles.
Do not use hazardous chemicals to clean or come into contact with
the unit. Do not use the unit in the presence of inflammable
substances or vapour such as alcohol, insecticides, petrol,etc.
Do not allow children to operate the unit unsupervised.
Do not use this product for functions other than those described in this
instruction manual.
NEVER DO THIS
3
Portable air conditioners exhaust large amounts of room air. Always
ensure an adequate supply of make-up air to operate efficiently.
Important Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
To prevent injury to the user or other people and property damage, the following instructions must be followed.
Incorrect operation resulting from to ignoring these instructions may cause harm or damage.
ENERGY SAVING
TIPS
Use the unit in the recommended room size.
Locate the unit where furniture cannot obstruct the air flow.
Keep blinds/curtains closed during the sunniest part of the day.
Keep the filters clean.
Keep doors and windows closed to keep cool air in and warm air out
(cooling mode).
OPERATING
CONDITION
The air conditioner must be operated within the temperature range
indicated below:
TOOLS FOR WINDOW
KIT INSTALLATION
1. Screwdriver (medium size, Phillips)
2. Tape measure or ruler
3. Knife or scissors
4. Saw (In the event that the window kit needs to be cut down in size
because the window is too narrow for direct installation).
See www.danby.com for general instruction guide.
Identifying Parts
WARNING
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Avoid fire hazard or electric shock. Do not use an extension cord
or an adaptor plug. Do not remove any prong from the power
cord.
ELECTRICAL
INFORMATION
WARNING
Be sure the electrical supply is adequate for the model you have
chosen. This information can be found on the serial plate, which
is located on the side of the cabinet and behind the grille.
Be sure the air conditioner is properly grounded. To minimize
shock and fire hazards, proper grounding is important. The
power cord is equipped with a three-prong grounding plug for
protection against shock hazards.
Your air conditioner must be used in a properly grounded wall
receptacle. If the wall receptacle you intend to use is not
adequately grounded or protected by a time delay fuse or circuit
breaker, have a qualified electrician install the proper receptacle.
Ensure the receptacle remains accessible after the unit is
installed.
4
MODE
COOL
DRY
*HEAT (heat pump type)
*HEAT (electrical or heat pump)
ROOM TEMPERATURE
17°C (62°F) ~ 35°C (95°F)
13°C (55°F) ~ 35°C (95°F)
5°C (41°F) ~ 30°C (86°F)
<30°C / 86°F
(*) Optional feature, some models may not have this feature.
Note: Performance may be reduced outside of these operating
temperatures.
Identifying Parts
ACCESSORIES
TEMP
AUTO
COOL
DR
Y
HEAT
F
AN
HIGH
MED
LO
W
MODE
F
AN SPEED
SWING
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
RE
SE
T
L
O
CK
FOLLO W
ME
LED
DISPLAY
ION
TURBO
PARTS
PART NAME
QUANTITY
Exhaust hose and Adaptor
B (round mouth)
1 set
Foam seal
Remote Controller and
Battery (For remote control
models only)
1set
Drain hose
1pc
• Ensure that all the accessories are included in the package and refer to the installation
instructions for their usage.
NOTE: All the illustrations in this manual are for explanatory purposes only. Your air conditioner
may be slightly different.
UNIT STRUCTURE
1
2
3
5
4
FRONT
1
2
3
4
Control Panel
Horizontal Louver Blade
(adjusts manually)
Carrying Handle
(both sides)
Remote Signal Receptor
Front Panel
Fig.1
5
5
Window Slider Kit and screw
1 set
6 pc
Identifying Parts
REAR
6
7
8
9
10
11
12
13
Upper Air Filter (behind the grille)
Air Outlet
Castor
Air Intake
Drain Outlet
Air Intake
Lower Air Filter (behind the grill)
Bottom tray drain outlet
Fig.2
Features
ELECTRONIC CONTROL
INSTRUCTIONS
Before you begin, thoroughly familiarize yourself with the control panel
and remote controller and all its functions. Select the functions you desire
based on the associated symbol.
The unit can be controlled by the control panel alone or with the remote
controller.
NOTE: This manual does not include Remote Controller Operation. Refer
to the <<Remote Controller Instructions>> packed with the unit for this
information.
Fig.3
6
8
9
12
11
6
7
13
10
1
7
4
66
2
3
5
Features
1
ELECTRONIC CONTROL
INSTRUCTIONS
MODE select button
Selects the appropriate operating mode. Each time you press the but-
ton, a mode is selected in a sequence that goes from AUTO, COOL,
TIMER button
Used to initiate the AUTO ON start time and AUTO OFF stop time pro-
gram, in conjuction with the up arrow & down arrow buttons.
POWER button
Turns power on/off.
SLEEP button
Used to initiate the SLEEP operation.
FAN button
UP and DOWN buttons
Used to adjust (increase /decrease) temperature settings (1°C/2°F
increments) in a range of 17°C(62°F) to 30°C(86°F) or the TIMER set-
ting in a range of 0~24hrs. The control is capable of displaying
temperature in degrees Fahrenheit or degrees Celsius. To convert
from one to the other, press and hold the Up and Down buttons at the
same time for 3 seconds.
LED Display
Shows the set temperature in °C or °F and the Auto-timer settings.
While on DRY and FAN modes, it shows the room temperature.
Also displays the following error codes:
E1 - Room temperature sensor error-Unplug the unit and plug
it back in. If error repeats, call for service.
E2 - Evaporator temperature sensor error- Unplug the unit and
plug it back in. If error repeats, call for service.
E4 - Display panel communication error - Unplug the unit and
plug it back in. If error repeats call for service.
P1 - Bottom tray is full - Connect the drain hose and drain the
collected water away. If error repeats, call for service.
2
3
4
5
7
7
6
DRY, FAN and HEAT (not available on cooling only models). The mode
indicator light corresponding to the chosen setting lights up.
Controls the fan speed. Press to toggle between two fan speeds: LOW
(press 1 time) and HIGH (press 2 times). The fan speed indicator light
indicates the corresponding fan setting. Press the button a third time to
initiate AUTO-FAN mode. In this mode, both indicator lights will light up.
E3 - Condenser temperature error - Unplug the unit and plug it
back in. If error repeats call for service.
Operating Instructions
OPERATING MODES
COOL mode
- Press the "MODE" button until the "COOL" indicator light comes on.
- Press the up / down arrows to select your desired room temperature.
The temperature can be set within a range of 17°C-30°C / 62°F-86°F.
- Press the "FAN SPEED" button to choose the fan speed.
DRY mode
- Press the "MODE" button until the "DRY" indicator light comes on.
- Under this mode, you cannot select a fan speed or adjust the
temperature. The fan motor operates at LOW speed.
- Keep windows and doors closed for the best dehumidifying effect.
- Do not use the window hose under this mode.
AUTO mode
- When you set the air conditioner in AUTO mode, it will automatically
select cooling, heating (applicable models only) or fan only operation
depending on what temperature you have selected and the room
temperature.
- The air conditioner will adjust the room temperature automatically to
the temperature point set by you.
- Under AUTO mode, you can not select the fan speed.
FAN mode
- Press the "MODE" button until the "FAN " indicator light comes on.
TIMER mode
- To initiate the TIMER OFF function, press the timer button when the unit
is on. It indicates the Auto Stop program is initiated.
- To initiate the TIMER ON function, press the timer button when the unit
is off. It indicates the Auto Start program is initiated.
- Press and hold the UP or DOWN button to change the Auto-time by half
hour increments, up to 10 hours, then at 1 hour increments up to 24
hours. The control will count down the time remaining until the unit
starts or stops.
- The selected time will program in 5 seconds and the system will
automatically revert back to display the previous temperature setting.
- Turning the unit ON or OFF at any time or adjusting the timer setting
to 0.0 will cancel the Auto Start/Stop timed program.
- When a malfunction (E1, E2, E3, E4, P1) occurs, the Auto Start/ Stop
program will be cancelled.
8
- Press the "FAN SPEED" button to choose the fan speed (1 time for LOW,
2 times for HIGH, 3 times for AUTO-FAN).
- The corresponding fan speed indicator light for each speed lights up. Both
indicators are lit up when AUTO-FAN is selected.
- The temperature cannot be adjusted.
- Do not use the window hose in this mode.
HEAT mode (select models only)
- Press the "MODE" button until the "HEAT" indicator light comes on.
- Press the ADJUST buttons "up" or "down" to select your desired
room temperature. The temperature can be set within a range of
17°C-30°C / 62°F-86°F.
- Press the "FAN SPEED" button to choose the fan speed. For some
models, the fan speed can not be adjusted under HEAT mode.
Operating Instructions
POWER OUTAGE
In the case of a power outage or interruption, the unit will automatically
re-start with the default settings after the power is restored.
Wait 3 minutes before resuming operation
After the unit has stopped, it can not operate for the first 3 minutes. This
is to protect the unit. Operation will automatically start after 3 minutes.
AIR FLOW DIRECTION
ADJUSTMENT
Adjust the air flow direction manually (Fig. 4):
The louver can be set to the desired position manually.
- Do not place any heavy objects or other loads on the louver, doing so
will cause damage to the unit.
- Ensure the louver is fully opened under heating operation.
Fig.4
9
Adjust
manually
OPERATING MODES
SLEEP cycle
This unit features an operation mode that is designed to keep you
comfortable while sleeping, and save you money on your energy bill.
Simply press the sleep button. Depending on whether the unit is in heat-
ing or cooling mode, the temperature will either increase (cooling mode)
or decrease (heating mode) by 1°C / 2°F every half hour for 1 hour. It will
then hold this new temperature for 7 hours before returning to the original
temperature setting and resuming normal operation.
NOTE: This feature is unavailable in FAN and DRY mode.
-
Installation Instructions
LOCATION
The air conditioner should be placed on a firm foundation to minimize
noise and vibration. For safe and secure positioning, place the unit on a
smooth, level floor strong enough to support the unit.
The unit has casters to aid placement, but it should only be rolled on
smooth, flat surfaces. Use caution when rolling on carpeted surfaces.
Use caution and protect floors when rolling over wood floors. Do not
attempt to roll the unit over objects.
The unit must be placed within reach of a properly rated grounded
socket.
Never place any obstacles around the air inlet or outlet of the unit.
Allow at least 30cm of space away from the wall for efficient air
conditioning.
WINDOW SLIDER KIT
INSTALLATION
Your window slider kit has been designed to fit most standard vertical and
horizontal window applications, However, it may be necessary for you to
modify some aspects of the installation procedures for certain types of
windows. Please refer to Fig. 6& Fig.7 for minimum and maximum win-
dow openings. The window slider kit can be fastened with a screw (see
Fig.8).
NOTE: If the window opening is less than the mentioned minimum length
of the window slider kit, cut the end without the whole in it short enough
to fit in the window opening. Never cut out the hole in window slider
kit. (visit www.danby.com for general instruction videos.)
30c
m
30cm
Fig.5 Fig.6
Fig.7 Fig.8
Vertical
Window
Window Slider Kit
Minimum:72.0cm(2.36ft).
Maxmum:207.0m(6.79ft).
Horizontal
Window
Window Slider Kit
Minimum:72.0cm(2.36ft).
Maxmum:207.0cm(6.79ft).
Screw
Window
slider
kit
10
Installation Instructions
INSTALLATION IN A
DOUBLE- HUNG SASH
WINDOW
1. Measure the adhesive foam seal to fit the window stool. Then cut the
foam seal to the proper length and attach it to the window stool. Fig.9
2. Attach the window slider kit to the window stool. Adjust the length of
the window slider kit according to the width of window. Shorten the
adjustable window kit if the width of window is less than 28. 3 inches.
Open the window sash and place the window slider kit on the window
stool. Fig.10
3. Cut the foam seal (adhesive type) to the proper length and attach it on
the top of the window. Shown in Fig.11
4. Close the window sash securely against the window.
5. Cut the foam seal to an appropriate length and seal the open gap
between the top window sash and outer window sash. Shown in
Fig.12.
Foam seal A
(adhesive type)
Fig.9
Fig.10
Window Kit
Window Stool
Fig.11
Window Kit
Window Stool
Fig.12
Foam seal
11
Foam seal B
Foam seal B
28.34 ~ 81.5
Installation Instructions
INSTALLATION IN A
SLIDING SASH
WINDOW
1. Measure the adhesive foam seal to fit the window stool. Cut the foam
seal (adhesive type) to the proper length and attach it to the window
frame. See Fig.13.
2. Attach the window slider kit to the window stool. Adjust the length of
the window slider kit according to the height of window. Shorten the
adjustable window kit if the height of window is less than 28.3inches.
Open the window sash and place the window slider kit on the window
stool. See Fig.14.
3. Cut the foam seal(adhesive type) to the proper length and attach it on
the top of the window. Shown in Fig.15.
4. Close the sliding sash securely against the window.
5. Cut the foam seal to the appropriate length and seal the open gap
between the top window sash and outer window sash. Shown in
Fig.16.
Foam seal A
(adhesive type)
Fig.13
Fig.14
Window
Panel
Fig.15
Foam
Seal
Fig.16
12
Foam seal
28.34 ~ 81.5
Installation Instructions
EXHAUST HOSE
INSTALLATION:
The exhaust hose and adaptor must be installed or removed in
accordance with the usage mode.
COOL, HEAT(heat pump type) or AUTO mode
FAN, DEHUMIDIFY mode
Install
Remove
1. Install the window exhaust adaptor B onto the exhaust hose as shown
in Fig.17. or Fig.18. Refer to the previous pages for window kit
installation.
2. Push the exhaust hose into the air outlet opening along the arrow
direction (See Fig.19).
The hose can be compressed or extended moderately according to the
installation requirement, but it is desirable to keep the hose length to a
minimum.
IMPORTANT
DO NOT OVER BEND THE HOSE. (see Fig.21)
Fig.17
Fig.18
Fig.19
13
Installation Instructions
WATER DRAINAGE
• During dehumidifying modes, remove the drain plug from the back of the
unit, install the drain connector (5/8” universal female connecter) with
3/4” hose (not included). For the models without a drain connector, just
attach the drain hose to the hole. Place the open end of the hose
directly over the drain area in your basement floor. Please refer to
Fig.22a, b & 23.
• When the water level of the bottom tray reaches a predetermined level,
the unit beeps 8 times, the digital display area shows P1. At this time
the air conditioning/dehumidification process will immediately stop.
However, the fan motor will continue to operate (this is normal).
Carefully move the unit to a drain location, remove the bottom drain plug
and let the water drain away (Fig.24). Restart the machine until the P1
symbol disappears. If the error repeats, call for service.
NOTE: When operating or draining water always protect carpeting or
floors from possible water spillage.
Remove the
drain plug
Continuous
drain hose
Fig.22a
Fig.23
Fig.24
14
Fig.22b
The drain
plug
Care and Maintenance
AIR FILTER
IMPORTANT
1) Be sure to unplug the unit before cleaning or servicing.
2) Do not use gasoline, paint thinner or other chemicals to clean
the unit.
3) Do not wash the unit directly under a tap or using a hose.
It may cause electrical damage.
4) If the power cord is damaged, contact the service depot
immediately.
Clean the air filter at least once every two weeks. Accumulation of dust
will hinder fan operation.
REMOVAL
This unit has two filters. Grasp the upper filter tab and take it
out in the direction of the arrow as shown in Fig.25. Remove the lower fil-
ter by grasping the filter tab and removing it in the direction of the arrow
as shown in Fig.25.
CLEANING
Wash the air filter by submerging it gently in warm water (about 40°C /
104 °F) with a neutral detergent. Rinse the filter and dry it in a shady
place.
REPLACING
Install the upper and lower air filters after cleaning. Reinsert them in the
direction of the arrow. (see Fig.26). *Filters should be dry before installing.
NOTE: The upper (lower) grills and the upper (lower)air filters are
connected and can be separated.
UNIT ENCLOSURE
Use a lint-free cloth soaked with neutral detergent to clean the unit
enclosure. Finish by wiping with a dry clean cloth.
LONG TERM
STORAGE
• Remove the rubber plug at the back of the unit and attach a hose to
the drain outlet. Place the open end of the hose directly over the drain
area in your basement floor (See page 14).
• Remove the plug from the bottom drain outlet, all the water in the bottom
tray will drain out (See page 14).
• Keep the appliance running on FAN mode for half a day in a warm room
to dry the appliance inside and prevent mold formation.
• Turn off the appliance and unplug it, wrap the cord and bundle it with tape.
• Remove the batteries from the remote controller.
• Clean the air filter and reinstall it.
Upper filter
(Take out)
Lower filter
(Take out)
Fig.25
Upper filter
(Install)
Lower filter
(Install)
Fig.26
15
Troubleshooting
Occasionally, a problem may arise that is minor in nature, and a service call may not be necessary. Use this trou-
bleshooting guide for a possible solution. If the unit continues to operate improperly, call an authorized service depot or
Danby’s Toll Free Number 1-800-263-2629 for assistance.
Unit does not start
when pressing on/off
button
• P1 appears in the display window
• Room temperature is lower than
the set temperature. (Cooling mode)
• Drain the water in the bottom tray.
• Reset the temperature.
Not cool enough
• The windows or doors in the room
are not closed.
• There are heat sources inside the
room.
• Exhaust air hose is not connected or
blocked.
• Temperature setting is too high.
• Air filter is blocked by dust.
• Make sure all the windows and
doors are closed.
• Remove the heat sources if possible.
• Connect the hose and make sure it
can function properly.
• Decrease the set temperature.
• Clean the air filter.
PROBLEM
POSSIBLE CAUSE
SOLUTION
Noisy or vibration
• The ground is not level or not flat
enough.
• Place the unit on a flat, level ground
if possible.
Gurgling sound
• The sound comes from the flowing
of the refrigerant inside the
air conditioner
• It is normal
Power shuts off in
heating mode
• The automatic overheat protection
function. When the temperature at the
air outlet exceeds 70°C/158°F, the
device will stop.
• Turn on again after the unit
has cooled down. Reduce
temperature setting.
16
LIMITED IN-HOME APPLIANCE WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating
conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter
“Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.
First Year
During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s
option, at no charge to the ORIGINAL purchaser.
To obtain
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance
Service
requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at
their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service
must be performed by a qualied service technician.
If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all
obligations of Danby under this warranty shall be void.
Boundaries of
If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be
In Home Service
delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for
warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he
responsibility of the purchaser.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due
to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its
authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees
under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages
to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of
the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions
(extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).
Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our
AUTHORIZED SERVICE DEPOT.
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: (519) 837-0920 FAX: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: (419) 425-8627 FAX: (419) 425-8629
04/09
1-800-263-2629
Warranty Service
In-home
If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest
service center your unit must be delivered to the nearest authorized Danby Service Depot, as service
must only be performed by a technician qualified and certified for warranty service by Danby. Transpor-
tation charges to and from the service location are not protected by this warranty and are the responsi-
bility of the purchaser.
During the first twelve (12) months, any functional parts of this product found to be defective, will be
repaired or replaced, at warrantor’s option, at no charge to the ORIGINAL purchaser.
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized
Service Depot. Any appliance requiring service outside the limited boundaries of “In Home Service” ,it
will be the consumer’s responsibility to transport the appliance (at their own expense) to the original
retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Service” below.
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby
service depot, where service must be performed by a qualified service technician. If service is performed
on the units by anyone other than an authorized service depot, or the unit is used for commercial
application, all obligations of Danby under this warranty shall be void.
First Year
To obtain
Service
Boundaries of
In Home Service
LIMITED IN-HOME APPLIANCE WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is
used under the normal operating conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or
Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other
contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or
implied, made or intended by Danby or its authorized distributors and all other warranties, conditions, representations or
guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation
or statute is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages to persons
or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit
and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for
damages to persons or property caused by the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating
conditions (extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for
outdoor application). Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event
warranty service is required, present this document to our AUTHORIZED SERVICE DEPOT.
Warranty Service
In-home
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: (519) 837-0920 FAX: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: (419) 425-8627 FAX: (419) 425-8629
1-800-263-2629
07/13
Bienvenue
18
Bienvenue dans la famille Danby. Nous sommes ¿ ers de la qualité de nos produits et nous croyons fermement au service
par une assistance ¿ able. Vous découvrirez au travers de ce quide, facile d’utilisation et vous en aurez la con¿ rmation par
notre service d’assistance à la clientèle. Mais ce qui est encore mieux, vous pourrez béné¿ cier de ces valeurs à chaque
utilisation de votre appareil. Ceci est important parce que votre nouvel appareil fera partie de votre famille pour long-
temps.
S’il vous plaît écrivez informations ci-dessous; ces renseignements seront nécessaires si votre appareil a besoin
d’entretien ou pour les demandes de renseignements généraux. Pour béné¿ cier d’une opération de maintenance
ou dépannage, le reçu original sera exigé.
Numéro de modèle :
Numéro de série :
Date d’achat :
BESOIN D’ASSISTANCE ?
Veuillez trouver quelques conseils avant de faire appel à nos
services, cela nous aidera à mieux vous servir:
Lisez ce guide:
Il comprend des instructions pour l’utilisation et l’entretien
adapté de votre unité.
Si votre nouvel appareil est endommagé :
Contactez immédiatement le revendeur (ou le fabricant).
Gagnez du temps et de l’argent :
Avant de faire appel à nos services, consultez à nouveau
la section « “Dépannage ». Cette section vous aidera à
solutionner des problèmes courants.
Si une réparation est nécessaire, ne vous inquiétez pas, la
solution est au bout de l’appel téléphonique.
Tel: 1-800-26-
(1-800-263-2629)
AVERTISSEMENT :
Une ¿ che de mise à la terre mal branchée peut entraîner un risque d’incendie, de
choc électrique ou de blessures aux personnes qui utilisent l’appareil. Si vous
n’êtes pas certain que l’appareil est correctement mis à la terre, consultez un
préposé du service quali¿ é.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Danby DPA085B1GB Le manuel du propriétaire
- Catégorie
- Climatiseurs mobiles
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Danby DPA085B1GB Owner's manual
Documents connexes
-
Danby DPA100B2WDB Mode d'emploi
-
-
Danby DPA120B1WB Le manuel du propriétaire
-
-
-
-
-