NAPOLEON HDX52PT-2 Manuel utilisateur

FRENCH

PG. 63

W415-2363 / A / 11.01.19

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleon.com • [email protected]

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA /

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

- Installation and service must be

performed by a qualiﬁ ed installer, service

agency, or the supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁ ed kit is used.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

WARNING

!

ENGLISH

$10.00

FOR INDOOR USE ONLY

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

HDX52NT-2

HDX52PT-2

INSTALLATION AND

OPERATION MANUAL

STARﬁ re™ Series

HDX52NT-2 Illustrated with SB52

SAFETY BARRIER

W415-2363 / A / 11.01.19

EN

2

safety information

• This appliance is hot when operated and

can cause severe burns if contacted.

• Any changes or alterations to this

appliance or its controls can be

dangerous and is prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Ensure the glass door is opened or removed

when lighting the pilot for the ﬁ rst time and

when the gas supply has run out.

• Risk of ﬁ re or asphyxiation, do not operate

appliance with ﬁ xed glass removed and never

obstruct the front opening of the appliance.

• Do not connect 110 volts to the control valve,

with the exception of models; GSST8 and

GT8.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during

installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing

and operating the appliance.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at

test pressures above 1/2 psig. Close the manual shut-off valve before pressure testing gas line at test

pressures equal to or less than 1/2 psig (35mb).

• The appliance must not be operated at temperatures below freezing (32°F / 0°C). Allow the appliance

to warm to above freezing prior to operation, with the exception of models; GSS36, GSS42; these

appliances are suitable for 0°F / -18°C.

• Children and adults should be alerted to hazards of high surface temperature and should stay

away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the

appliance. Toddlers, young children and others may be susceptible to accidental contact

burns. A physical barrier is recommended if there are at risk individuals in the house. To

restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers,

young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from

furniture and draperies.

• Furniture or other objects must be kept a minimum of 4 feet (1.22m) away from the front of the appliance.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is off, it will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior

to operating the appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the

appliance and venting system are kept clean. The appliance and its venting system should be inspected

before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and

free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it

serviced. Keep burner and control compartment clean.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner ﬂ ame

patterns.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and

shall be installed for the protection of children and other

at-risk individuals.

!

WARNING

EN

W415-2363 / A / 11.01.19

3

safety information

!

WARNING

• Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this

appliance.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has

been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁ ed service person, if equipped.

• Do not strike or slam shut the appliance glass door, if equipped.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Carbon or soot should not occur in a vent free appliance as it can distribute into the living area of your

home. If you notice any signs of carbon or soot, immediately turn off your appliance and arrange to have

it serviced by a qualiﬁ ed technician before operating it again.

• If equipped, the screen must be in place (closed) when the appliance is in operation.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating

to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of

the exhaust escaping through these openings can also cause the surrounding combustible materials to

overheat and catch ﬁ re.

• Carbon monoxide poisoning may lead to death; early signs of carbon monoxide poisoning resemble the

ﬂ u, with headache, dizziness and/or nausea. If you have these signs, the appliance may not be working

properly. Get fresh air at once! Have appliance serviced. Some people; pregnant women, persons with

heart or lung disease, anemia, those under the inﬂ uence of alcohol, those at high altitudes are more

affected by carbon monoxide than others. Failure to keep the primary air opening(s) of the burner(s) clean

may result in sooting and property damage.

• As with any combustion appliance, we recommend having your appliance regularly inspected and

serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and

your family against Carbon Monoxide (not applicable for outdoor appliances).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a TV or other electronic components.

• For appliances equipped with a safety barrier; if the barrier becomes damaged, the barrier

shall be replaced with the manufacturer’s barrier for this appliance.

• Installation and repair should be done by a qualiﬁ ed service person. It is imperative that control

compartments, burners and circulating air passageways of the appliance be kept clean.

• For outdoor products only: this appliance must not be installed indoors or within any structure that

prevents or inhibits the exhaust gases from dissipating in the outside atmosphere.

• If applicable, the millivolt version of this appliance uses and requires a fast acting thermocouple. Replace

only with a fast acting thermocouple supplied by Wolf Steel Ltd.

!

WARNING

!

Disconnect the appliance main gas valve/control

from the supply piping when pressure testing that

system at pressures in excess of 1/2 psi (3.5 kPa).

Isolate the appliance with it’s shut off valve during

any pressure testing of the supply piping at

pressures equal to or less than 1/2 psi (3.5 kPa).

FIRE RISK HAZARD / DELAYED IGNITION

High supply pressure will damage the valve / controls.

Add California Prop 65 warning

!

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

W415-2363 / A / 11.01.19

EN

4

table of contents

1.0 general information 5

1.1 rates and efﬁ ciencies 5

1.2 rating plate information 7

1.3 mobile home installation 7

1.4 dimensions 8

2.0 venting 9

2.1 typical vent installation 10

2.2 vent terminal clearances 11

2.3 vent application ﬂ ow chart 12

2.4 deﬁ nitions 12

2.5 elbow vent length values 12

2.6 horizontal termination 13

2.7 vertical termination 15

3.0 installation 17

3.1 horizontal installation 18

3.2 vertical installation 18

3.3 using ﬂ exible vent components 19

3.4 horizontal air terminal installation 19

3.5 vertical air terminal installation 20

3.6 appliance vent connection 21

3.7 gas installation 21

4.0 framing 22

4.1 installing non-combustible board 25

4.2 minimum clearance to combustible

enclosures 27

4.3 minimum combustible mantel

clearances 29

4.4 non-combustible facing material 30

5.1 safety screen removal / installation 31

5.0 finishing 31

5.2 latch door engaging / disengaging 32

5.3 glass door removal / installation 33

5.4 burner installation 34

5.5 logo placement 34

6.1 hard wiring connection 35

6.2 receptacle wiring diagram 35

6.0 electrical information 35

6.3 battery holder installation 36

6.4 wiring diagram 37

7.0 operation 38

7.1 general transmitter layout 38

7.2 initializing the transmitter/battery holder

for the ﬁ rst time 38

7.3 tempature display 38

7.4 ﬂ ame height 39

7.5 night light dimmer control 39

7.6 continuous pilot / intermittent pilot (CPI /

IPI) selection 39

7.7 key lock 39

7.8 low battery / manual bypass 39

7.9 optional blower speed control 39

8.0 operating instructions 40

8.1 pilot-on-demand 41

9.0 adjustments 42

9.1 restricting vertical vents 42

9.2 pilot burner adjustment 42

9.3 venturi adjustment 43

9.4 ﬂ ame characteristics 43

10.0 maintenance 44

10.1 annual maintenance 45

10.2 control access 46

10.3 burner removal 47

10.4 brick panel removal 47

10.5 porcelain panel removal 47

10.6 media tray removal (glass only) 47

10.7 night light replacement 48

10.8 care of glass 49

10.9 care of plated parts 49

11.0 replacement parts 50

11.1 overview 51

12.0 accessories 52

13.0 log burner 54

14.0 glass burner 55

15.0 relief door assembly 56

16.0 valve train assembly 57

17.0 troubleshooting 58

18.0 warranty 61

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel

Ltd. reserves the right to change or modify any information within this manual at any time without

notice. Changes, other than editorial are denoted by a vertical line in the margin.

note:

EN

W415-2363 / A / 11.01.19

5

standard checklist

1.0 general information

Installer, please ﬁ ll out the following information:

Customer: ________________________________________________________________________

Address: ________________________________________________________________________

Date of Installation: ________________________________________________________________________

Location of Appliance: ________________________________________________________________________

Installer: ________________________________________________________________________

Dealer/Distributor contact number: ________________________________________________________________________

Serial #: ________________________________________________________________________

Model:

Natural Gas: HDX52NT-2 Propane: HDX52PT-2

This appliance is approved for bathroom, bedroom, and bed-sitting room installations and is certiﬁ ed for mobile

home installation.

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile

home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for

use with other gases, unless a certiﬁ ed kit is used.

When the appliance is installed at elevations above 4,500ft (1371m), and in the absence of speciﬁ c

recommendations from the local authority having jurisdiction, the certiﬁ ed high altitude input rating shall be

reduced at the rate of 4% for each additional 1,000ft (305m).

Expansion / contraction noises during heating up and cooling down cycles are normal and are to be expected.

Change in ﬂ ame appearance from “HI” to “LO” is more evident in natural gas than in propane.

note:

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your

municipality for recycling instructions.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the appli-

ance and must be installed.

1.1 rates and efﬁ ciencies

HDX52-2

NG P

Altitude (FT) 0-4,500

Max. Input (BTU/HR) 55,000

Max. Output Steady State (BTU/HR) 37,391 36,500

Min. Inlet Gas Supply Pressure 4.5" w.c. (11mb) 11" w.c. (27mb)

Max. Inlet Gas Supply Pressure 13" w.c. (17mb) 13" w.c. (32mb)

Manifold Pressure (Under Flow Conditions) 3.5" w.c. (9mb) 10" w.c. (25mb)

W415-2363 / A / 11.01.19

EN

6

general information

!

WARNING

• Always light the pilot - whether for the ﬁ rst time or if the gas supply has run out - with the glass door

opened or removed.

• Provide adequate clearance for servicing and operating the appliance.

• Provide adequate ventilation.

• Never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 48” (121.9cm) from the front face of

the appliance.

• Surfaces around and especially above the appliance can become hot. Avoid contact when appliance is

operating.

• Fire risk. Explosion hazard.

• Use only Wolf Steel approved optional accessories and replacement parts with this appliance using non-

listed accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result

in a safety hazard and will void the warranty and certiﬁ cation.

THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local

codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for

example in the state of Massachusetts:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of

Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas

log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (0.9m).

• A carbon monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed

combustion product.

The installation must conform with local codes or, in absence of local

codes, the National Gas and Propane Installation Code CSA B149.1

in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54

in the United States. Suitable for mobile home installation if installed

in accordance with the current standard CAN/CSA Z240MH Series,

for gas equipped mobile homes, in Canada or ANSI Z223.1 and

NFPA 54 in the United States.

The appliance and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing

of that system at test pressures in excess of 1/2 psig (35 mb).

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any

pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed

with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the

absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National

Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a

properly grounded receptacle. The grounding prong must not be removed from the cord plug.

The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable

and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat

created. The location of windows, doors and, the trafﬁ c ﬂ ow in the room where the appliance is to be located should be

considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or

roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the

appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.

We suggest that our gas

hearth products be installed

and serviced by professionals

who are certied in the U.S.

by the National Fireplace

Institute

®

(NFI) as NFI Gas

Specialists

www.ncertied.org

EN

W415-2363 / A / 11.01.19

7

general information

Certiﬁed to Canadian and American National Standards: CSA 2.22-XXXX / ANSI Z21.50-XXXX for Vented Decorative Gas Appliances

Certiﬁé selon les normes Nationales Canadiennes et Américaines: CSA 2.22-XXXX / ANSI Z21.50-XXXX pour les Appareils à gaz décoratif à évacuation

Direct vent, vented gas ﬁreplaces. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in accordance with the current

standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance

must be installed in accordance with local codes, if any; if none, follow the current ANSI Z223.1 or CSA B149. For use with barrier WXXX-XXXX. Follow installation instructions.

Foyer à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile si son installation

conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis selon la norme 24 CFR, Part 3280,

Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser la norme NFPA 501A, Fire Safety Criteria for Manufactured

Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou, en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou

CSA B149 en vigueur. Utiliser uniquement avec l’écran WXXX-XXXX. Suivre les instructions d’installation.

9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)

WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada

XXXX XXXX XXXX XXXX

MODEL / MODÈLE

Altitude

Input

Reduced Input

P4

Élévation

Alimentation

Alimentation Réduite

P4

Manifold Pressure: 3.5” w.c. (NG)

Minimum Supply Pressure: 4.5” w.c. (NG)

Maximum Supply Pressure: 7”* w.c. (NG)

Pression au Collecteur: 3,5” d’une colonne d’eau (GN)

Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN)

Pression d’Alimentation Max.: 7” ** d’une colonne d’eau (GN)

** Maximum inlet pressure not to exceed 13”.

Manifold Pressure: 10” w.c. (P)

Minimum Supply Pressure: 11” w.c. (P)

Maximum Supply Pressure: 13”* w.c. (P)

Pression au Collecteur: 10” d’une colonne d’eau (P)

Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)

Pression d’Alimentation Max.: 13” * d’une colonne d’eau (P)

** Pression d’alimentation maximale ne devait pas dépasser 13”.

0-XXXXft (0-XXXXm)

Minimum clearance to combustible materials:

Top, sides & back: per standoff spacers for framing and ﬁnishing

materials. For non-combustible framing and ﬁnishing materials,

see installation manual.

Top X”

Floor X”

Sides X”

Back X”

Vent top X”

Vent sides & bottom X”

Recessed depth X”

*** Mantel X” from appliance opening

Dégagements minimaux des matériaux combustibles:

Dessus, côtés et arrière: selon les espaceurs de dégagements

pour les matériaux d’ossature selon le manuel du propriétaire

pour les matériaux de ﬁnition.

Dessus X”

Plancher X“

Côtés X”

Arrière X“

Dessus du conduit d’évent X”

Côtés et dessous du conduit d’évent X”

Profondeur d’encastré une face X”

*** Tablette X” de l’ouverture de l’appareil

WARNING: Do not add any material to the appliance which will come in contact with the

ﬂames, other than that supplied by the manufacturer with the appliance.

AVERTISSEMENT: N’ajoutez pas à cet appareil aucun matériau devant entretien

contact avec les ﬂammes autre que celui qui est fourni avec cet appareil par le fabricant.

*** Maximum horizontal extension:

X”. See installation manual for

greater extensions, minimum vent

lengths and maximum vent lengths.

*** L’extension horizontale maximale: X”.

Référez au manuel d’installation pour des

extensions plus grandes, les longueurs

d’évacuation minimaux et maximum.

The appliance must be vented using the appropriate Napoleon vent kits. See installation

manual for venting speciﬁcations. Proper reinstallation and resealing is necessary after servicing

the vent-air intake system.

L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au

manuel d’installation pour les spéciﬁcations d’évacuation. Il est nécessaire de bien réinstaller et

resceller l’évacuation après avoir executer l’entretien du système de prise d’air.

Serial Number / N° de Série:

W385-XXXX

REFERENCE# 161746

XXXX

VENTED DECORATIVE GAS APPLIANCE: NOT A SOURCE OF

HEAT, NOT INTENDED FOR USE AS A HEATING

APPLIANCE, NOT FOR USE WITH SOLID FUEL.

APPAREIL À GAZ DÉCORATIF À ÉVACUATION: N’EST PAS

UNE SOURCE DE CHALEUR; N’EST PAS DESTINÉ À ÈTRE

UTILISÉ COMME UN APPAREIL DE CHAUFFAGE; NE

CONVIENT PAS AUX COMBUSTIBLES SOLIDES.

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY.

POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE

CERTIFIÉES AVEC L’APPAREIL.

XX,XXX XX,XXX

For natural gas when equipped with No. XX drill size oriﬁce.

For propane when equipped with No. XX drill size oriﬁce.

Convient au gaz naturel quand l’appareil est muni d’un injecteur de diamètre no. XX.

Convient au propane quand l’appareil est muni d’un injecteur de diamètre no. XX.

Electrical rating: 115V, 60HZ. Less than 12 amperes.

Spéciﬁcations électriques: 115V, 60HZ. Moins de 12 ampère.

XX.X% XX.X%

XXXX XXXX XXXX XXXX

SAMPLE

pliance ance

ructions.uctions.

installation stallation

4 CFR, Part 3280, art 3280,

afety Criteria for Manufactured Manufactu

es d’installation

AN

S

I Z22

3

.1

ou

223.1 ou

Él

é

v

a

ti

o

n

Élévatio

Ali

m

e

nt

a

t

io

n

mentation

Alim

e

nt

a

ti

o

n R

édu

it

eAlimentation Réduite

P4P4

GN)N)

’eau (GN)(GN)

Ma

n

ifold

P

r

essu

r

e

:

fold Pressure:

1

0” w.c.

(

P

)w.c. (P)

Minimum

S

upply Pressure:

Minimum Supply Pressure:

11” w.c.

(

P

)11” w.c. (P)

M

aximum Su

pp

l

y

Pressure:

Maximum Supply Pressure:

1

3”* w.c.

(

P

)13”* w.c. (P)

Pression au

C

ollecteur:

sion au Collecteu

1

0” d’une colonne d’eau

(

P

)0” d’une colonne d’eau (P)

P

r

essio

n

d’Ali

m

e

nt

a

t

io

n

Mi

n.:

Alimentation Min.:

1

1” d’une colonne d’eau

(

P

)” d’une colonne d’eau (P)

P

r

essio

n

d’Ali

m

e

nt

a

t

io

n

Ma

x.:

Pression d’Alimentation Max.:

1

3” * d’une colonne d’eau

(

P

)13” * d’une colonne d’ea

** Pression d’alimentation maximale ne devait pas dépasser 13”.** Pression d’alimentation maximale ne devait pas dépasser 1

erials:

ers for framing and ﬁnishing s for framing and ﬁnishing

framing and ﬁnishing materials, framing and ﬁnishing materials,

peningning

Dégagements minimaux des matériaux combustiDégagements minimaux des matériaux combus

Dessus, côtés et arrière: selon les espaceurs de dégDessus, côtés et arrière: selon les espaceurs

pour les matériaux d’ossature selon le manueour les matériaux d’ossature selon le man

pour les

l extension: l extension:

ual for al for

um vent

m vent

lengths.

R

NTED DECORATIVE GAS APPLIANCE: NOT ADECORATIVE GAS APPLIANCE: NOT A

HEAT, NOT INTENDED FOR USE AS

APPLIANCE, NOT FOR USE WITAPPLIANCE, NOT FOR USE W

APPAREIL À GAZ DÉCORATIF À ÉVACPPAREIL À GAZ DÉCORATIF À ÉVA

UNE SOURCE DE CHALEUR; NUNE SOURCE DE CHALEUR

UTILISÉ COMME UNUTILISÉ COMME U

CONVIENVIE

FOR USE WITH GFO

POU

L

XX

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

The rating plate must remain with the appliance at all times. It must not be removed.

note:

1.2 rating plate information

1.3 mobile home installation

This appliance must be installed in accordance with the manufacturer’s instructions and the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home

Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas

indicated on the rating plate.

This mobile/manufactured home listed appliance comes factory equipped with a means to secure the appliance. Built

in appliances are equipped with 1/4” (6.4mm) diameter holes located in the front left and right corners of the base.

Use appropriate fasteners, inserted through the holes in the base to secure. For free standing products contact your

local authorized dealer / distributor for the appropriate securing kit. For mobile home installations, the appliance must

be fastened in place. It is recommended that the appliance be secured in all installations. Always turn off the pilot and

the fuel supply at the source, prior to moving the mobile home. After moving the mobile home and prior to lighting the

appliance, ensure that the logs are positioned correctly.

This appliance is certiﬁ ed to be installed in an aftermarket permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible

for use with other gases, unless a certiﬁ ed kit is used.

Conversion Kits

This appliance is ﬁ eld convertible between Natural Gas (NG) and Propane (P).

To convert from one

g

as to another, consult

y

our Authorized dealer/distributor.

W415-2363 / A / 11.01.19

EN

8

general information

56 7/8"

1445mm

54 13/16"

1392mm

50 3/8"

1280mm

41 7/8"

1064mm

27 1/8"

689mm

29 1/8"

740mm

47 17/32"

1207mm

44 3/4"

1137mm

2"

51mm

38 7/8"

987mm

Ø 10 7/8"

276mm

Ø 7 7/8"

200mm

9 3/16"

233mm

TOP VIEWRIGHT SIDE VIEWFRONT VIEW

1.4 dimensions

EN

W415-2363 / A / 11.01.19

9

2.0 venting

THIS APPLIANCE USES A 8” (203.2mm) EXHAUST / 10” (254mm) AIR INTAKE VENT PIPE SYSTEM.

Refer to the section applicable to your installation.

For safe and proper operation of the appliance follow the venting instruction exactly. Deviation from the minimum

vertical vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations,

allow several minutes (5-15) for the ﬂ ame to stabilize after ignition. Provide a means for visually checking the vent

connection to the appliance after the appliance is installed. Use a ﬁ restop, vent pipe shield or attic insulation shield

when penetrating interior walls, ﬂ oor or ceiling.Although not a requirement, it is recommended for vent lengths that

pass through unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a

protective sleeve to minimize condensation.

The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint

suitable for 400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is

recommended.

For vent systems that provide seals on the inner exhaust ﬂ ue, only the outer air intake joints must be sealed using a

red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent

pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance ﬂ ue collar

which must be sealed using the black high temperature sealant Mill Pac.

When using Wolf Steel venting components: Use only approved Wolf Steel ﬂ exible components with the following

termination kits: wall terminal kit GD622R, or 1/12 to 7/12 pitch roof terminal kit GD610, 8/12 to 12/12 roof terminal

kit GD611 or ﬂ at roof terminal kit GD612. With ﬂ exible venting, in conjunction with the various terminations, use either

the 5 foot (1.5m) vent kit GD620 or the 10 foot (3m) vent kit GD630.

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows

to a minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to

verify that it is unobstructed and undamaged.

The minimum allowable vertical vent length is 3 feet (0.9m) maximum allowable vertical vent length is 40 feet (12m).

The maximum number of allowable 8” (203mm) vent connections is three horizontally or vertically (excluding the

appliance and the air terminal connections).

When venting, the horizontal run must be kept to a minimum of 36” (914mm) or a maximum of 20 feet (6m). If a 20

foot (6m) horizontal run is required, the appliance must have a minimum vertical rise immediately off the appliance of

57” (1448mm). When terminating vertically, the vertical rise is a minimum 36” (914mm) and a maximum 40 feet (12m)

above the appliance.

For optimum performance, it is recommended that all horizontal runs have a minimum 1/4” (6mm) rise

per foot/meter. Provide a means for visually checking the vent connection to the appliance after the

appliance is installed. Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows.

Keep it pulled tight. A 3/4” (19mm) air gap between the inner and outer liner all around is required for safe

operation. Use a ﬁ restop when penetrating interior walls, ﬂ oor or ceiling.

!

WARNING

• Risk of ﬁ re! Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• The vent system must be supported every 3ft (0.9m) for both vertical and horizontal runs. Use supports or

equivalent non-combustible strapping to maintain the required clearance from combustibles. Spacers are attached

to the inner pipe at pre-determined intervals to maintain an even air gap to the outer pipe. This gap is required for

safe operation. A spacer is required at the start, middle, and end of each elbow to ensure this gap is maintained.

These spacers must not be removed.

note:

If for any reason the vent air intake system is disassembled, re-install per the instructions provided for the

initial installation.

note:

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing

alternate constructions such as a chimney as part of the vent system is not permitted.

W415-2363 / A / 11.01.19

EN

10

venting

2.1 typical vent installation

Refer to “VENTING” section.

EN

18" (45.7cm)

MAXIMUM

24″ (61cm)

MIN.

71 1/2"

(181.6cm)

PLUS RISE *

16″ (40.6cm)

MINIMUM

40 FEET (12m)

MAXIMUM

3 FEET (0.9m)

MINIMUM

47 1/2"

(120.7cm)

47 1/2"

(120.7cm)

EN

W415-2363 / A / 11.01.19

11

venting

2.2 vent terminal clearances

Covered balcony applications ††*

Q

MIN

R

MAX

R

= 3 feet

(0.9m)

= 2 x

IHHW

(4.6m)

Q

ACTUAL

R

Q

S

G

P

INSTALLATIONS

CANADA U.S.A.

A

12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.

B

12” (30.5cm)

Δ

9” (229mm)

Δ

Clearance to windows or doors that open.

C

12” (30.5cm)* 12” (30.5cm)* Clearance to permanently closed windows.

D

18”

(45.7cm)**

18”

(45.7cm)**

Vertical clearance to ventilated sofﬁ ts located above the terminal within a horizontal distance of 2’ (0.6m)

from the center line of the terminal.

E

12” (30.5cm)** 12” (30.5cm)** Clearance to unventilated sofﬁ t.

F

0” (0mm) 0” (0mm) Clearance to an outside corner wall.

G

0” (0mm)*** 0” (0mm)***

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

2” (51mm)*** 2” (51mm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

H

3’(0.9m) 3’(0.9m)****

Clearance to each side of the center line extended above the meter / regulator assembly to a maximum

vertical distance of 15’ (4.6m).

I

3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

J

12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

K

6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

L

7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

M

12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch or deck.

N

16” (40.6cm) 16” (40.6cm) Clearance above the roof.

O

2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

P

8’ (2.4m) 8’ (2.4m)

Roof must be non-combustible without openings.

Q

3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

R

6’ (1.8m) 6’ (1.8m)

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening

between the terminal and the open side of the structure.

S

12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony

Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁ ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements, check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂ oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements, check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

Clearances are to be in accordance with local

installation codes and the requirements of the gas

supplier. In their absence, clearances are to be as

listed above and are based on national codes.

note:

Wall terminals are for illustration purposes only. Size and

shapes may vary.

W415-2363 / A / 11.01.19

EN

12

venting

2.3 vent application ﬂ ow chart

2.4 deﬁ nitions

2.5 elbow vent length values

Top Exit

Horizontal Termination

Vertical rise is equal

to or greater than the

horizontal run

Vertical rise is equal

to or greater than the

horizontal run

Vertical rise is less

than horizontal run

Vertical rise is less

than horizontal run

Horizontal run +

vertical rise to

maximum of

24.75 feet (7.5m)

Horizontal run +

vertical rise to

maximum of

19 (5.8m)

4.2 times the vertical

rise equal to or

greater than the

horizontal run

3 times the vertical

rise equal to or

greater than the

horizontal run

Horizontal run +

vertical rise to

maximum of

40 feet (12.2m)

Horizontal run +

vertical rise to

maximum of

40 feet (12.2m)

Vertical Termination

For the following symbols used in the venting calculations and

examples are:

> - greater than

> - equal to or greater than

< - less than

< - equal to or less than

H

T

- total of both horizontal vent lengths (Hr) and offsets (Ho) in feet

H

R

- combined horizontal vent lengths in feet

H

O

- offset factor: .03 (total degrees of offset - 90°*) in feet

H

O

- offset factor: .03 (total degrees of offset - 135°*) in feet

V

T

- combined vertical vent lengths in feet

Feet Inches Millimeters

1° 0.03 0.5 12.7

15° 0.45 6.0 152.4

30° 0.9 11.0 279.4

45° 1.35 16.0 406.4

90°* 2.7 32.0 812.8

* The ﬁ rst 90° offset has a zero value and is shown in the formula as - 90°

* The ﬁ rst 45° and° offset have a zero value and is shown in the formula as -45° and -90° respectively

or -135° when combined (for 45° exit only).

EN

W415-2363 / A / 11.01.19

13

venting

2.6 horizontal termination

Simple venting conﬁ guration (only one 90° elbow)

(H

T

) < (V

T

)

For vent conﬁ gurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: H

T

< V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 3 FT (0.9m)

V

2

= 8 FT (2.4m)

V

T

= V

1

+ V

2

= 3 FT (0.9m ) + 8 FT (2.4m) = 11 FT (3.4m)

H

1

= 2.5 FT (0.8m)

H

2

= 2 FT (0.6m)

H

R

= H

1

+ H

2

= 2.5 FT (0.8m) + 2 FT (0.6m) = 4.5 FT (1.4m)

H

O

= .03 (three 90° elbows - 90°) = .03 (270° - 90°) = 5.4 FT (1.7m)

H

T

= H

R

+ H

O

= 4.5 FT (1.4m) + 5.4 FT (1.6m) = 9.9 FT (3m)

H

T

+ V

T

= 9.9 FT (3m) + 11 FT (3.4m) = 20.9 FT (6.4m)

Formula 1: H

T

< V

T

9.9 FT (3m) < 11 FT (3.4m)

Formula 2: H

T

+ V

T

< 40 FT (12.2m)

20.9 FT (6.4m) < 40 FT (12.2m)

Since both formulas are met, this vent conﬁ guration is acceptable.

See graph to determine the required vertical

rise V

T

for the required horizontal run H

T

.

The shaded area within the lines represents

acceptable values for H

T

and V

T

0

2.5

(0.8)

5

(1.5)

7.5

(2.3)

10

(3.1)

12.5

(3.8)

15

(4.6)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

17.5

(5.3)

20

(6.1)

39 (11.9)

REQUIRED

VERTICAL

RISE IN FEET

(METERS)V

T

HORIZONTAL VENT RUN PLUS OFFSET IN

FEET (METERS) H

T

90°

V

1

V

2

H

1

H

2

2 (0.6)

18"

W415-2363 / A / 11.01.19

EN

14

venting

(H

T

) > (V

T

)

Simple venting configuration (only one 90° elbow)

See graph to determine the required vertical rise V

T

for the

required horizontal run H

T

.

REQUIRED

VERTICAL RISE

IN INCHES

(MILLIMETERS)

V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

T

For vent configurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: H

T

< 4.2 V

T

Formula 2: H

T

+ V

T

< 24.75 feet (7.5m)

Example:

V

1

= V

T

= 6 FT (1.8m)

H

1

= 3 FT (0.9m)

H

2

= 5 FT (1.5m)

H

R

= H

1

+ H

2

= 3FT (0.9m) + 5FT (1.5m) = 8 FT (2.4m)

H

O

= .03 (two 90° elbows - 90°) = .03 (180° - 90°) = 2.7FT (0.8m)

H

T

= H

R

+ H

O

= 8FT (2.4m) + 2.7FT (0.8m) = 10.7FT (3.3m)

H

T

+ V

T

= 10.7FT (3.3m) + 6FT (1.8m) = 16.7FT (5.1m)

Formula 1: H

T

< 4.2 V

T

4.2 V

T

= 4.2FT (1.3m) x 6FT (1.8m) = 25.2FT (7.7m)

10.7FT (3.3m) < 25.2FT (7.7m)

Formula 2: H

T

+ V

T

< 24.75 FT (7.5m)

16.7FT (5.1m) < 24.75 (7.5m)

Since both formulas are met, this vent configuration is acceptable.

0

5

(1.5)

15

(4.6)

20 (6.1)

100 (2540)

50 (1270)

150 (3810)

12.5

(3.8)

19 1/2

(495.3)

57 (1447.8)

147

(3733.8)

2

(0.6)

The shaded area within the lines represents acceptable

values for H

T

and V

T

90°

V

1

H

1

H

2

90°

Example:

V

1

= 4 FT (1.2m)

V

2

= 1.5 FT (0.5m)

V

T

= V

1

+ V

2

= 4FT (1.2m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

H

1

= 2 FT (0.6m)

H

2

= 1 FT (0.3m)

H

3

= 1 FT (0.3m)

H

4

= 1.5 FT (0.5m)

H

R

= H

1

+ H

2

+ H

3

+ H

4

= 2FT (0.6m) + 1FT (0.3m) + 1FT (0.3m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

H

O

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 5.5 FT (1.7m) + 8.1 FT (2.5m) = 13.6 FT (4.2m)

H

T

+ V

T

= 13.6 FT (4.2m) + 5.5 FT (1.7m) = 19.1 FT (5.8m)

Formula 1: H

T

< 4.2 V

T

4.2 V

T

= 4.2 FT (1.3m) x 5.5 FT(1.7m) = 23.1 FT (7m)

13.6 FT (4.2m) < 23.1 FT (7m)

Formula 2: H

T

+ V

T

< 24.75 FT (7.5m)

19.1FT (5.8m) < 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

90°

H

1

H

2

V

1

V

2

H

3

H

4

10

(3.1)

19.5

(5.9)

50 (1270)

100 (2540)

150 (3810)

5

(1.5)

18

(5.5)

12.5

(3.8)

19

(5.9)

10

(3.1)

15

(4.6)

20

(6.1)

0

57 (1447.8)

24 (609.6)

147 (3733.8)

EN

W415-2363 / A / 11.01.19

15

venting

2.7 vertical termination

(H

T

) < (V

T

)

Simple venting conﬁgurations.

See graph to determine the required vertical rise V

T

for the

required horizontal run H

T

.

REQUIRED

VERTICAL

RISE IN FEET

(METERS) V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

T

For vent conﬁgurations requiring one or more 90° elbows the following formulas apply:

Formula 1: H

T

< V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 5 FT (1.5m)

V

2

= 6 FT (1.8m)

V

3

= 10 FT (3.1m)

V

T

= V

1

+ V

2

+ V

3

= 5FT (1.5m) + 6FT (1.8m) + 10FT (3.1m) = 21FT (6.4m)

H

1

= 8 FT (2.4m)

H

2

= 2.5 FT (0.8m)

H

R

= H

1

+ H

2

= 8FT (2.4m) + 2.5FT (0.8m) = 10.5 FT (3.2m)

H

O

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 10.5FT (3.2m) + 8.1FT (2.5m) = 18.6FT (5.7m)

H

T

+ V

T

= 18.6FT (5.7m) + 21FT (6.4m) = 39.6FT (12.1m)

Formula 1: H

T

< V

T

18.6FT (5.7m) < 21FT (6.4m)

Formula 2: H

T

+ V

T

< 40 FT (12.19m)

39.6FT (12.1m) < 40FT (12.2m)

Since both formulas are met, this vent conﬁguration is acceptable.

90°

V

1

V

2

H

1

H

2

The shaded area within the lines represents acceptable

values for H

T

and V

T

90°

0

5

(1.5)

10

(3.1)

15

(4.6)

20

(6.1)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

3 (0.9)

V

3

W415-2363 / A / 11.01.19

EN

16

venting

(H

T

) > (V

T

)

Simple venting conﬁgurations.

See graph to determine the required vertical rise V

T

for the

required horizontal run H

T

.

REQUIRED

VERTICAL

RISE IN FEET

(METERS) V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

T

For vent conﬁgurations requiring more than two 90° elbows the following formulas apply:

Formula 1: H

T

< 3V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 2 FT (0.6m)

V

2

= 1 FT (0.3m)

V

3

= 1.5 FT (0.5m)

V

T

= V

1

+V

2

+V

3

= 2FT (0.6m) + 1FT (0.3m) + 1.5FT (0.5m) = 4.5FT (1.4m)

H

1

= 6 FT (1.8m)

H

2

= 2 FT (0.6m)

H

R

= H

1

+ H

2

= 6FT (1.8m) + 2FT (0.6m) = 8 FT (2.4m)

H

O

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 8FT (2.4m) + 8.1FT (2.5m) = 16.1FT (4.9m)

H

T

+ V

T

= 16.1FT (4.9m) + 4.5FT (1.4m) = 20.6 FT (6.3m)

Formula 1: H

T

< 3V

T

3V

T

= 3FT (0.9m) x 4.5FT (1.4m) = 13.5FT (4.1m)

16.1FT (4.9m) > 13.5FT (4.1m)

Since this formula is not met, this vent conﬁguration is unacceptable.

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

20.6FT (6.3m) < 40 (12.2m)

Since only formula 2 is met, this vent conﬁguration is unacceptable and a new appliance location or vent conﬁguration

will need to be established to satisfy both formulas.

The shaded area within the lines represents acceptable

values for H

T

and V

T

0

5

(1.5)

10

(3.1)

15

(4.6)

20

(6.1)

10 (3.1)

20 (6.1)

3 (0.9)

25

(7.6)

30

(9.1)

19 (5.8)

90°

V

1

V

2

H

1

H

2

90°

V

3

18

(5.5)

2 (0.6)

EN

W415-2363 / A / 11.01.19

17

For optimum performance it is recommended that all horizontal runs have a minimum of 1/4" (6.4mm) rise per foot

(0.3m) using ﬂ exible venting. For safe and proper operation of the appliance, follow the venting instructions exactly.

For clearance to combustible materials from the vent pipe, see “framing” section.

3.0 installation

!

WARNING

• Ensure to unpack all loose materials from inside the ﬁ rebox prior to connecting the gas and electrical supply

• If your appliance is supplied with a remote, ensure the remote receiver is in the “OFF” position prior

to connecting the gas and electrical supply to the appliance.

• For safe and proper operation of the appliance, follow the venting instructions exactly.

• The appliance exhaust ﬂ ue collar must be sealed using Mill Pac. All exhaust and intake vent pipe joints

must be sealed using red RTV high temp silicone sealant (W573-0002) (not supplied) or black high temp Mill

Pac (W573-0007) (not supplied).

• If using pipe clamps to connect rigid vent components, a minimum of 3 screws must also be used to ensure

the connection cannot slip off.

• Do not clamp the ﬂ exible vent pipe.

• Risk of ﬁ re, explosion, or asphyxiation. Improper support of the entire venting system may allow vent to sag

and separate. Use vent run supports and connect vent sections per installation instructions.

• Risk of ﬁ re, do not allow loose materials or insulation to touch the vent pipe. Remove insulation to allow for the

installation of the attic shield and to maintain clearances to combustibles.

• Do not ﬁ ll the space between the vent pipe and enclosure with any type of material. Do not pack insulation

or combustibles between ceiling ﬁ restops. Always maintain speciﬁ ed clearances around venting and ﬁ restop

systems. Install wall shields and ﬁ restops as speciﬁ ed. Failure to keep insulation or other materials away from

vent pipe may cause ﬁ re.

• For gas stoves only: If the appliance is installed directly on carpeting, vinyl tile, or other combustible material

other than wood ﬂ ooring, the appliance shall be installed on a metal or wood panel extending the full width and

depth, unless otherwise tested.

W415-2363 / A / 11.01.19

EN

18

installation

3.1 horizontal installation

3.2 vertical installation

This application occurs when venting through an exterior

wall. Having determined the correct height for the air

terminal location, cut and frame a hole in the exterior wall,

as illustrated, to accommodate the ﬁ restop assembly. Dry

ﬁ t the ﬁ restop assembly before proceeding to ensure the

brackets on the rear surface ﬁ t to the inside surface of the

horizontal framing.

The vent shield must be installed to the full depth of the

combustible wall. The length of the vent shield may cut

shorter for combustible walls that less than 6” (152mm)

thick.

A. Apply a bead of caulking (not supplied) around the

corner edge of the inside surface of the ﬁ restop

assembly, ﬁ t the ﬁ restop assembly to the hole and

secure using 4 screws.

B. Once the vent pipe is installed in its ﬁ nal position, apply red RTV silicone (W573-0002) (not supplied)

between the pipe and the ﬁ restop.

Bend the tabs for reduced side clearances or move

the shield for reduced top clearances. Do not ﬁ ll

the air space between the ﬁ restop spacer and the

exterior wall with any type of insulating material (i.e.

spray foam).

note:

DETERMINE

THE

CORRECT

HEIGHT

CAULKING

FIRESTOP

SPACER

VENT

SHIELD

FINISHING

MATERIAL

CAULKING

note:

The above is for illustration purposes only. Vents do

not always pass through center of frame.

ADD

HEIGHT

ADD

WIDTH

• The ﬁ restop assembly must be installed with the vent shield to the top.

• Terminals must not be recessed into a wall or siding more than the depth of the return ﬂ ange of the mounting

plate.

!

WARNING

This application occurs when venting through a roof. Installation kits for

various roof pitches are available from your authorized dealer / distributor.

See the “accessories” section to order speciﬁ c kits required.

A. Determine the air terminal location, cut and frame a square opening,

as illustrated, in the ceiling and the roof to provide the minimum 1"

(25mm) clearance between the vent pipe and any combustible material.

Try to center the vent pipe location midway between two joists to

prevent having to cut them. Use a plumb bob to line up the center of

the openings. A vent pipe shield will prevent any materials such as

insulation, from ﬁ lling up the 1" (25mm) air space around the pipe. Nail

headers between the joist for extra support.

B. Apply a bead of caulking (not supplied) to the framework or to the

Wolf Steel vent pipe shield plate or equivalent (in the case of a ﬁ nished

ceiling), and secure over the opening in the ceiling. A ﬁ restop must be

placed on the bottom of each framed opening in a roof or ceiling that

the venting system passes through. Apply a bead of caulking all around

and place a ﬁ restop spacer over the vent shield to restrict cold air from

being drawn into the room or around the ﬁ replace. Ensure that both

spacer and shield maintain the required clearance to combustibles.

Once the vent pipe is installed in its ﬁ nal position, apply red RTV

silicone (W573-0002) (not supplied) between the pipe and the ﬁ restop

assembly.

C. In the attic, slide the vent pipe collar down to cover up the open end

of the shield and tighten. This will prevent any materials, such as

insulation, from ﬁ lling up the 1" (25mm) air space around the pipe.

Caulking

Vent Pipe

Shield

Vent

Pipe

Shield

Vent

Pipe

Collar

Firestop

underside

of joist

15 1/2”

(39.3cm)

14 1/2”

(36.8cm)

EN

W415-2363 / A / 11.01.19

19

installation

3.3 using ﬂ exible vent components

3.4 horizontal air terminal installation

For safe and proper operation of the appliance, follow the venting instructions

exactly.

The vent system must be supported approximately every 3 feet (0.9m) for

both vertical and horizontal runs. Use Wolf Steel Ltd. support ring assembly

or equivalent noncombustible strapping to maintain the minimum clearance to

combustibles for both vertical and horizontal runs.

All inner ﬂ ex pipe and outer ﬂ ex pipe joints may be sealed using high temperature

red RTV silicone W573-0002 (not supplied) or the high temperature sealant W573-

0007 Mill Pac (not supplied). However, the high temperature sealant W573-0007

Mill Pac (not supplied) must be used on the joint connecting the inner ﬂ ex pipe and

the exhaust ﬂ ue collar.

Use only approved ﬂ exible vent pipe kits marked:

“Wolf Steel Approved Venting” or “E2” as identiﬁ ed by the stamp only on the ﬂ ex pipes.

Elbow

Spacers

• Do not allow the inner ﬂ ex pipe to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight.

• Spacers are attached to the inner ﬂ ex pipe at predetermined intervals to maintain an even air gap to the outer

ﬂ ex pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each

elbow to ensure this gap is maintained. These spacers must not be removed.

!

WARNING

A. Stretch the inner ﬂ ex pipe to the required length taking

into account the additional length needed for the ﬁ nished

wall surface. Apply a heavy bead of the red RTV silicone

(W573-0002) (not supplied) to the inner sleeve of the air

terminal. Slip the vent pipe a minimum of 2” (50.8mm)

over the inner sleeve of the air terminal and secure with a

minimum of 3 screws.

B. Using the outer ﬂ ex pipe, slide over the outer combustion

air sleeve of the air terminal and secure with a minimum

of 3 screws. Seal using red RTV silicone (W573-0002)

(not supplied).

C. Insert the vent pipes through the ﬁ restop maintaining

the required clearance to combustibles. Holding the air

terminal (lettering in an upright, readable position), secure

to the exterior wall and make weather tight by sealing

with caulking (not supplied).

D. If more vent pipe needs to be used to reach the ﬁ replace,

couple them together, as illustrated. The vent system

must be supported approximately every 3 feet (0.9m) for

both vertical and horizontal runs. Use non-combustible

strapping to maintain the minimum clearance to

combustibles.

E. Stove Appliances Only: From inside the house, using

Red RTV Silicone (W573-0002) (not supplied), seal

between the vent pipe and the ﬁ restop. Then slide the black trim collar over the vent pipe up to the

ﬁ restop.

The air terminal mounting plate may be recessed into the exterior wall or siding no greater than the

depth of its return ﬂ ange.

ADD FA

S

TENER TYP

E

ADD GRAPHIC

Screws

(Supplied)

2" (50.8mm) Overlap

Outer Flex Pipe

Inner Flex

Pipe

Red RTV Silicone

Caulking

Red RTV Silicone

Screws

Inner Coupler

Outer Coupler

Outer Flex

Pipe

Inner Flex

Pipe

Outer Flex

Pipe

W415-2363 / A / 11.01.19

EN

20

installation

3.5 vertical air terminal installation

A. Fasten the roof support to the roof using 6 screws. The roof support is

optional. In this case, the venting is to be adequately supported using

either an alternate method suitable to the authority having jurisdiction or

the optional roof support.

B. Stretch the inner ﬂ ex pipe to the required length. Slip the inner ﬂ ex

pipe a minimum of 2” (51mm) over the inner pipe of the air terminal

connector and secure with a minimum of three screws, when 4/7, 5/8

and 3/5 venting is used and a minimum of six screws when using 8/10

or 8/11 venting. Seal using a heavy bead of red RTV silicone sealant

(W573-0002) (not supplied).

C. Repeat using the outer ﬂ ex pipe, using a heavy bead of red RTV

silicone sealant (W573-0002) (not supplied) and a minimum of three

screws, when 4/7, 5/8 and 3/5 venting is used and a minimum of six

screws when using 8/10 or 8/11 venting.

D. Thread the air terminal connector / vent pipe assembly down through

the roof. The air terminal must be positioned vertically and plumb.

Attach the air terminal connector to the roof support, ensuring that the

top of the air terminal is 16” (40.6cm) above the highest point that it

penetrates the roof.

E. Remove nails from the shingles, above and to the sides of the air

terminal connector. Place the ﬂ ashing over the air terminal connector

leaving a min. 3/4” (19mm) of the air terminal connector showing above

the top of the ﬂ ashing. Slide the ﬂ ashing underneath the sides and

upper edge of the shingles. Ensure that the air terminal connector is

properly centered within the ﬂ ashing, giving a 3/4” (19mm) margin all

around. Fasten to the roof. Do not nail through the lower portion of the

ﬂ ashing. Make weather-tight by sealing with caulking. Where possible,

cover the sides and top edges of the ﬂ ashing with rooﬁ ng material.

F. Aligning the seams of the terminal and air terminal connector, place the

terminal over the air terminal connector making sure the vent pipe goes

into the hole in the terminal. Secure with a minimum of three screws,

when 4/7, 5/8 and 3/5 venting is used and a minimum of six screws

when using 8/10 or 8/11 venting.

G. Apply a heavy bead of weatherproof caulking 2” (51mm) above the

ﬂ ashing. Install the storm collar around the air terminal and slide down

to the caulking. Tighten to ensure that a weather-tight seal between the

air terminal and the collar is achieved.

H. If more vent pipe needs to be used to reach the appliance, see “horizontal

air terminal installation” section.

Roof Support

Inner Flex Pipe

Inner Pipe

Red RTV

Silicone

(W572-0002)

Air

Terminal

Connector

Outer Flex Pipe

Storm Collar

Flashing

Caulking

Weather

Sealant

2” (51mm)

Air Inlet

Base

!

WARNING

• Maintain a minimum 2” (51mm) space between the air inlet base and the storm collar.

Fastening hardware provided with appropriate roof terminal and liner kits.

note:

La page charge ...

NAPOLEON HDX52PT-2 Manuel utilisateur

Ce manuel convient également à

NAPOLEON HDX52PT-2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents