Extron electronics FOX3 T 201 Manuel utilisateur

User Guide

FOX3 T 201

Fiber Optic Extender

Fiber Optic HDMI Transmitter

68-2865-01 Rev. B

05 21

Safety Instructions



Copyright

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks (

®

), registered service marks (

SM

), and trademarks (

TM

) are the property of RGBSystems, Inc. or Extron (see the

current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks

(

®

)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, eLink, Flat Field, FlexOS, Glitch Free, GlobalConfigurator,

GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NAV,

NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,

SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTPSystems, and ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu-RATEFrameLock), ADSP(Advanced Digital Sync Processing), AVEdge, CableCover, CDRS(ClassD Ripple Suppression),

Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator,

DSVP(Digital Sync Validation Processing), EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital,

Opti-Torque, PendantConnect, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), RoomAgent, Scope-Trigger, SIS, SimpleInstructionSet,

Skew-Free, SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause interference. This interference must be corrected at the expense of the user.

Battery Notice

This product contains a battery. Do not open the unit to replace the battery. If the

battery needs replacing, return the entire unit to Extron (for the correct address, see the

Extron Warranty section on the last page of this guide).

CAUTION: Risk of explosion. Do not replace the battery with an incorrect type.

Dispose of used batteries according to the instructions.

ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de

pile. Débarrassez-vous des piles usagées selon le mode d’emploi.

Class 1 Laser Product

Any service to this product must be carried out by Extron and its qualified service personnel.

CAUTION: Using controls, making adjustments, or performing procedures in a manner

other than what is specified herein may result in hazardous radiation exposure.

NOTE: For more information on safety guidelines, regulatory compliances,

EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and

Regulatory Compliance Guide” on the Extron website.

Produit laser de classe1

Si ce produit a besoin d’un quelconque entretient, celui-ci doit être fait par Extronet son

personnel qualifié.

ATTENTION : L’utilisation de commandes, la réalisation de réglages, ou l’exécution

de procédures de manière contraire aux dispositions établies dans le présent

document, présente un risque d’exposition dangereuse aux radiations.

Remarque : Pour plus d'informations sur les directives de sécurité, les conformités de

régulation, la compatibilité EMI/EMF, l'accessibilité, et les sujets en lien, consultez le

«Informations de sécurité et de conformité Extron» sur le site internet d'Extron.

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

DANGER:

• Will result in serious injury or death.

• Entraînera des blessures graves ou la mort.

WARNING: Potential risk of severe injury or death.

AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

TIP: A tip provides a suggestion to make working with the application easier.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,0p1 scene 1,1 ^B 51 ^W^C.0

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

E X! *X1&* X2)* X2#* X2! CE}

NOTE: For commands and examples of computer or device responses used in this

guide, the character “0” is the number zero and “O” is the capital letter “o.”

Computer responses and directory paths that do not have variables are written in the font

shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.

viiFOX3 T 201 Transmitter • Contents

Contents

Introduction ................................................1

About this Guide .................................................. 1

Product Description ............................................. 1

Fiber Cable Transmission Modes ..................... 2

Extron LinkLicense........................................... 3

Features .............................................................. 3

Installation and Operation............................ 5

Installation Overview ............................................ 5

Rear Panel Features ............................................ 5

Rear Panel Connections .................................. 5

Connector and Cable Details ............................. 10

HDMI Connectors .......................................... 10

RS-232 and IR ............................................... 11

TP Cable Termination and

Recommendations ....................................... 11

Front Panel Features .......................................... 12

Operation .......................................................... 12

Reset ............................................................. 12

Conﬁguration ..................................................... 14

EDID .............................................................. 14

HDCP ............................................................ 14

RS-232 Insertion............................................ 15

Audio Conﬁguration ........................................... 16

Audio Embedding .......................................... 16

Audio Input Gain ............................................ 16

Audio Input Configuration .............................. 16

Audio Mute .................................................... 16

SIS Conﬁguration and Control ...................17

Host Control Ports ............................................. 17

Rear Panel RS-232 Port ................................ 17

Front Panel Configuration USB Port ............... 17

Ethernet (LAN) Ports ...................................... 17

Establishing a Connection.............................. 18

Simple Instruction Set Control ........................... 19

Host-to-Unit Instructions ................................ 19

Device-Initiated Power-Up Message .............. 19

Error Responses ............................................ 19

Timeout ......................................................... 19

Using the Command and Response Table ..... 20

Common symbol definitions........................... 20

Command and Response Table for

SIS Commands ................................................ 22

Conﬁguration Software .............................26

Software/Firmware Installation ........................... 26

Connecting to PCS ............................................ 28

Device Discovery Panel .................................. 28

TCP/IP Panel ................................................. 29

Offline Device Preview .................................... 29

Software Overview ............................................. 30

Software Menu .............................................. 31

Device Menu.................................................. 33

Internal Web Page ..................................... 35

Accessing the Internal Web Page ...................... 35

Web Page Panels .............................................. 36

Device Info Panel ........................................... 36

Device Status Panel ....................................... 37

Network Settings Panel ................................. 37

Firmware Panel .............................................. 38

Roles and Permissions Panel ......................... 39

LinkLicense Panel .......................................... 40

About the FOX3T201 ................................... 41

Equipment Mounting ................................. 42

Mounting the Transmitter ................................... 42

Tabletop Use ................................................. 42

Mounting kits ................................................. 42

UL Rack-Mounting Guidelines ....................... 42

FOX3 T 201 Transmitter • Contents viii

FOX3 T 201 Transmitter • Introduction 1

Introduction

WARNING: The FOX3T201 output continuous invisible light (Class 1 rated),

which may be harmful to the eyes; use with caution.

AVERTISSEMENT : Le FOX3T201 émet une lumière invisible en continu (conforme à

la classe1) qui peut être dangereux pour les yeux, à utiliser avec précaution.

• Do not look into the rear panel fiber optic cable connectors or into the fiber optic

cables themselves.

• Ne regardez pas dans les connecteurs de câble fibre optique sur le panneau

arrière ou dans les câbles fibre optique eux-mêmes.

• Plug the attached dust cap into the optical transceiver when the fiber optic cable is

unplugged.

• Branchez la protection contre la poussière dans l’ensemble émetteur/récepteur

lorsque le câble ﬁbre optique est débranché.

About this Guide

This guide contains information about the Extron FOX3T201 fiber optic transmitter.

Product Description

The FOX3T201 transmitter is a ultra-high performance fiber optic extender for long haul

transmission of the following over two fiber optic cables (see figure1 on page2):

• Uncompressed or visually lossless HDCP-compliant 4096x2160 or 3840x2160 (UHD)

@60Hz video HDMI video

• 2-CH LPCM audio

• RS-232 and IR control signals

The transmitter extends HDMI signals up to:

• 20 km (12.4 miles) for the singlemode cables

• 500 m (1640 feet) with 50 µm OM4 4700 MHz bandwidth laser optimized multimode

cables

(see Fiber Cable Transmission Modes on page2).

The transmitter converts the HDMI video, the selected audio, and the RS-232 serial

communication into two proprietary data streams and outputs them as optical signals via

fiber optic small form factor pluggable (SFP) modules on two LC connector to a compatible

Extron FOX3 fiber optic receiver.

The transmitter has many controls, including audio adjustments, that are available under

Remote RS-232 and USB port Simple Set Instruction (SIS) control and PCS.

NOTE: The FOX3 products are not compatible with legacy FOX, FOXBOX, FOX II,

PowerCage 401 FOX, or PowerCage 1600 FOX products.

FOX3 T 201 Transmitter • Introduction 2

Fiber Cable Transmission Modes

The transmitter is further categorized by the type of fiber optic cable, multimode or

singlemode, which defines the effective range of transmission:

Multimode — Long distance, up to 500 m (1640 feet) (depending on the fiber cable)

Singlemode — Very long distance, up to 20 km (12.4 miles)

NOTE: The multimode and singlemode units are physically and functionally identical,

with the exception of the effective range of transmission. In this guide, any reference

applies to either transmission mode unless otherwise specified.

RS-232

REMOTE

POWER

12V

0.7 A MAX

Tx Rx G

A

OUT IN

B

OUT IN

LAN

RS-232

Tx

Rx

Tx RxG

IR

HDMI

FOX3 SR 201

R

AUDIO

CONTROL

OUTPUTS

CONTROL

RS

-232

REMOTE

POWER

12V

--A MAX

Tx

Rx G

A

OUT IN

B

OUT IN

RS-232

Tx

Rx Tx RxG

IR

HDMI

FOX3 T 201

R

AUDIO

CONTROL

INTPUTS

LOOP OUT

LAN

S

T

A

NDBY

CLASS 2 WI

R

IN

G

1

2

X

PA

1002

LEV

EL

1

2

1

2

L

I

M

I

T

ER

/

P

R

OT

ECT

SI

GN

A

L

2

I

NP

UTS

OUT

P

UT

R

E

M

O

T

E

0

V

OL

/

M

UT

E

10

V

5

0

m

A

1

0

-

2

4

0

V

1

.

3

A,

5

0

-

6

0

Hz

Ethernet

HDMI

Loop out

HDMI

Output

HDMI Input

Extron

SI 28

Surface-mount

Speakers

Extron

XPA 1002

Power Amplier

4K Display

Blu-ray Player

Local

Monitor

4K

Up to 20 km (12.43 miles)

Singlemode Fiber

SM Model

Audio

Output

RS-232

Extron

FOX3 T 201

Fiber Optic Transmitter

Extron

FOX3 SR 201

Fiber Optic Receiver

LAN

MODE

L

80

Figure 1. Typical FOX3T201 Transmitter Application

1

FOX3 T 201 Transmitter • Introduction 3

Extron LinkLicense

An Extron LinkLicense unlocks features that add convenience, expand system options, and

enhance the capabilities of Extron products. Each LinkLicense can be purchased separately

from the FOX3 device and activated as the need arises (A LinkLicense can be uploaded

using Extron Toolbelt software and the Toolbelt Help File. See Software/Firmware

Installation on page26 to download Toolbelt).

LinkLicense upgrades available for the FOX3 transmitter include the following:

• Uncompressed Video Upgrade —

• This LinkLicense is enabled once and lasts for the life of the product.

• Allows the FOX3 devices to pass uncompressed 4K @ 60 Hz video on the second

SFP module, enabling the highest video performance.

Features

• Transmits HDMI video, stereo audio, RS-232 control, and IR control signals

over fiber optic cabling.

• Supports mathematically lossless 4K video up to 4096x2160 at 60 Hz with 4:4:4

chroma sampling over one fiber.

• Supports uncompressed 4K video up to 4096x2160 at 60 Hz with 4:4:4 chroma

sampling over two fibers.

• Supported HDMI 2.0 specification features include data rates up to 18 Gbps

and Deep Color up to 12-bit.

• HDCP 2.3 compliant.

• Buffered HDMI input loop-through — Local HDMI output provides signals for a

local display, enabling monitoring or sharing of content without the need for a separate

distribution amplifier.

• Audio embedding — Analog stereo audio signals are converted to digital HDMI audio.

• User-selectable HDCP authorization — Allows the transmitter to appear HDCP

compliant or non-HDCP compliant to the connected source.

• Key Minder continuously verifies HDCP compliance for quick, reliable

switching — Authenticates and maintains continuous HDCP encryption between

input and output devices to ensure quick and reliable switching in professional AV

environments.

• EDID Minder automatically manages EDID communication between connected

devices — EDID Minder ensures that all sources power up properly and reliably output

content for display.

• Audio gain and attenuation adjustment capability — Setting the level of gain or

attenuation eliminates noticeable volume differences when switching between sources.

• Bidirectional RS-232 and IR signal transmission over fiber optic cabling for AV

device control — Bidirectional RS-232 and IR control pass-through enables a remote

device to be controlled without the need for additional cabling. Two fibers are required

for bidirectional communications.

• LinkLicense Support — Extron LinkLicense unlocks features that add convenience,

expand system functionality, and enhance the capabilities of Extron products.

• Front panel USB configuration port — Enables easy system configuration without

having to access the rear panel.

• Ethernet monitoring and control — Enables control and proactive monitoring over a

LAN, WAN, or the Internet.

FOX3 T 201 Transmitter • Introduction 4

• RS-232 control — Features an RS-232 serial port for control and configuration.

• Real-time status LED indicators for troubleshooting and monitoring — Front

and rear panel LEDs verify signal presence, HDCP authentication, fiber link status, and

power.

• Easy setup and commissioning with Extron’s PCS - Product Configuration

Software — Conveniently configures multiple products using a single software

application.

• Internal color bars test pattern for calibration and setup — Simplifies setup and

installation by providing a video signal when a source is unavailable.

• Compatible with Extron FOX3 Series matrix switchers — Creates HDCP-

compliant signal distribution systems.

• JITC Certified — Successfully completed interoperability and information assurance

testing for use in government applications and other mission-critical environments.

• Industry standard LC connectors provide reliable physical connectivity and

precise fiber core alignment.

• Available as an 850 nm multimode model for moderate-range transmissions up

to 500 m (1640 feet) and a 1310 nm singlemode model for extreme distances up

to 20 km (12.4 miles).

• 1" (2.5 cm) high, half rack width mountable metal enclosure.

• External Extron Everlast power supply — Provides worldwide power compatibility,

with high demonstrated reliability and low power consumption for reduced operating

cost.

• Extron Everlast Power Supply is covered by a 7-year parts and labor warranty.

FOX3 T 201 Transmitter • Installation and Operation 5

Installation and

Operation

This section details the installation of the FOX3T201 transmitter, including:

• Installation Overview

• Rear Panel Features

• Connector and Cable Details

• Front Panel Features

• Operation

• Audio Configuration

Installation Overview

Follow these steps to install and set up an Extron FOX3T201 transmitter for operation:

c

Turn off all of the equipment. Ensure that the video source and the output display are all

turned off and disconnected from the power source.

c

Mount the transmitter (see Equipment Mounting on page42).

c

Connect the cables and configure the units (see “Rear Panel Connections”, starting

below).

c

Plug in the power supplies, then turn on the display and the input.

Rear Panel Features

Rear Panel Connections

RS-232

REMOTE

POWER

12V

--A MAX

Tx Rx G

A

OUTIN

B

OUTIN

RS-232

Tx Rx Tx RxG

IR

HDMI

FOX3 T 201

R

AUDIO

CONTROL

INTPUTS

J

JH

H

HG

G

GC

C

CA

A

E

I

F

B

D

LOOP OUT

LAN

Figure 2. FOX3T201 Transmitter Rear Panel Features

A

Power inlet

F

Control RS-232/IR port

B

Power LED

G

Remote RS-232

C

Audio input

H

LAN Ethernet port

D

HDMI input

I

SFP module and LEDs

E

HDMI Loop Out

J

Reset button

2

FOX3 T 201 Transmitter • Installation and Operation 6

A

Power inlet (see figure2 on page5) — Connect the external 12 V, 2.0 A power

supply to the 2-pole captive screw inlet.

CAUTION: The DC output cables must be kept separate from each other while the

power supply is plugged in. Remove power before wiring

ATTENTION : Les câbles de sortie CC doivent être séparés les uns des autres

tant que la source d’alimentation est branchée. Coupez l’alimentation avant

d’effectuer les raccordements.

ATTENTION:

• Do not connect any external power supplies until you have read the Attention

notifications starting below.

• Veuillez lire les encadrés « Attention » à partir ci-dessous avant de brancher

une source d’alimentation externe.

SECTION A–A

Ridges

Smooth

A

3/16"

(5 mm) Max.

POWER

12V

--A MAX

Figure 3. Power Connector Wiring

1. Cut the DC output cord to the length needed.

2. Strip the jacket to expose 3/16inch (5mm) of the conductor wire (see figure3).

3. Ensure the connections have the correct polarity as shown in the figure above. The wire

with ridges is the ground wire.

4. Slide the exposed ends of the wire into the captive screw connector and secure by

tightening the screws.

5. Use the supplied tie wrap to strap the power cord to the extended tail of the connector.

ATTENTION:

• The length of the exposed wires in the stripping process is important. The

ideal length is 3/16 inches (5 mm). Any longer and the exposed wires may

touch, causing a short circuit between them. Any shorter and the wires can be

easily pulled out even if tightly fastened by the captive screws.

• La longueur des câbles exposés est importante lorsque l’on entreprend de

les dénuder. La longueur idéale est de 5 mm (3/16 inches). S’ils sont trop

longs, les câbles exposés pourraient se toucher et provoquer un court-

circuit. S’ils sont trop courts, ils peuvent être tirés facilement, même s’ils sont

correctement serrés par les borniers à vis.

• Do not tin the wire leads before installing into the connector. Tinned wires are

not as secure in the connector and could be pulled out. They may also break

after being bent several times.

• Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les

câbles étamés ne sont pas aussi bien fixés dans le connecteur et pourraient

être tirés. Ils peuvent aussi se casser après avoir été pliés plusieurs fois.

3

FOX3 T 201 Transmitter • Installation and Operation 7

ATTENTION:

• Always use a power supply provided by or specified by Extron. Use of an

unauthorized power supply voids all regulatory compliance certification and

may cause damage to the supply and the end product.

• Utilisez toujours une source d’alimentation fournie ou recommandée par

Extron. L’utilisation d’une source d’alimentation non autorisée annule toute

certification de conformité réglementaire, et peut endommager la source

d’alimentation et l’unité.

• If not provided with a power supply, this product is intended for use with a

UL Listed power source marked “Class 2” or “LPS” rated 12 VDC, 2.0 A

minimum.

• Si le produit n’est pas fourni avec une source d’alimentation, il doit être utilisé

avec une source d’alimentation certifiée UL de classe 2 ou LPS avec une

tension nominale de 12 Vcc, 2.0 A minimum.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air

handling spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs CA/CC ne conviennent pas à une

utilisation dans les espaces d’aération ou dans les cavités murales.

• The installation must always be in accordance with the applicable provisions

of National Electrical Code ANSI/NFPA 70, article 725 and the Canadian

Electrical Code part 1, section 16. The power supply shall not be permanently

fixed to building structure or similar structure.

• Cette installation doit toujours être conforme aux dispositions applicables du

Code américain de l’électricité (National Electrical Code) ANSI/NFPA 70, article

725, et du Code canadien de l’électricité, partie1, section16. La source

d’alimentation ne devra pas être fixée de façon permanente à une structure de

bâtiment ou à une structure similaire.

• Power supply voltage polarity is critical. Incorrect voltage polarity can damage

the power supply and the unit. The ridges on the side of the cord identify the

power cord negative lead (see figure3 on page6).

• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte

pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté

du cordon permettent de repérer le pôle négatif du cordon d’alimentation (voir

figure3).

• To verify the polarity before connection, plug in the power supply with no load

and check the output with a voltmeter.

• Pour vérifier la polarité avant la connexion, brancher l’alimentation hors charge

et mesurer sa sortie avec un voltmètre.

B

Power LED — The lit LED indicates power is applied and device is ready to transmit.

FOX3 T 201 Transmitter • Installation and Operation 8

C

Audio input (see figure2 on page5)— Connect an audio input device to the Audio

3.5 mm audio jack.

NOTE: The analog audio input on this

connector is in addition to the digital

audio embedded in the HDMI inputs. See

figure4 to identify the connector tip, ring,

and sleeve when making connections for

the transmitter from existing audio cables.

A mono audio connector consists of the

tip and sleeve. A stereo audio connector

consists of the tip, ring, and sleeve.

Sleeve ( )

Ring (

-

)

Tip (+)

3.5 mm Stereo Plug Connector

(balanced)

Figure 4. Audio Wiring Diagram

D

HDMI input — Connect a digital video input to this HDMI port. The transmitter also

accepts embedded digital audio on this port (see HDMI Connectors on page10 to

use the included Extron Lock-It Lacing Bracket).

E

HDMI Loop Out — If desired, connect a local monitor to this HDMI port.

F

Control RS-232 and IR port — Connect a serial RS-232 signal, a modulated

or unmodulated IR signal, or both to this 3.5 mm, 5-pole captive screw port for

bidirectional RS-232 and IR communication (see RS-232 and IR on page11 to wire

the connector).

NOTES:

• To receive responses from the controlled device over RS-232 or IR, two fiber

optic cables must be connected.

• The FOX3 system can pass RS-232 commands and responses at rates up to

115200 baud.

• RS-232 and IR can be active simultaneously.

G

Remote RS-232 port — For serial control of the transmitter, connect a host device,

such as a computer or touch panel control, via the 3-pole captive screw port (see

RS-232 and IR to wire this connector).

H

LAN Ethernet port — Connect the transmitter to an Ethernet LAN or WAN via this

RJ-45 port. Ethernet control allows the operator to configure the transmitter from a

remote location. When connected to an Ethernet LAN or WAN, the transmitter can be

accessed and operated from a computer running a standard Internet browser (see TP

Cable Termination and Recommendations on page11 to wire the connector).

• Link (green) LED — Indicates that the unit is properly connected to an Ethernet

LAN. This LED should light steadily.

• Act (yellow) LED — Indicates transmission of data packets on the RJ-45

connector. This LED should blink as the unit communicates.

NOTE: This is not a pass-through LAN connection

4

FOX3 T 201 Transmitter • Installation and Operation 9

I

SFP module and LEDs — (see figure2 on page5)

WARNING: The units output continuous invisible light (Class 1 rated), which

may be harmful to the eyes; use with caution. Plug the attached dust cap into the

optical transceiver when the fiber optic cable is unplugged.

AVERTISSEMENT : Le produit émet une lumière invisible en continu (conforme

à la classe1) qui peut être dangereux pour les yeux, à utiliser avec précaution

Branchez la protection contre la poussière dans l’ensemble émetteur/récepteur

lorsque le câble ﬁbre optique est débranché.

NOTES:

• Ensure the proper ﬁber cables for the transmitter and receiver pair are used.

Typically, singlemode ﬁber has a yellow jacket and multimode cable has an

orange or aqua jacket.

• See ﬁgure5 for ﬁber cable connections. Connect the transmitter to a receiver

in one of three ways:

• One way (transmitter to receiver) only, connect transmitter Outputs A (

1

) to

receiver Inputs A (

1

).

• Two way (transmitter to receiver and return), connect transmitter Outputs

A (

1

) to receiver Inputs A (

1

) and connect transmitter Outputs A (

2

) to

receiver Inputs A (

2

).

• Output B is available to transmit a 4K @ 60 Hz uncompressed signal when

the FOX3 4K @ 60 Hz Uncompressed Video LinkLicense is purchased.

1

Port A Out (required) — For all one-way video, audio,

and serial communications from the transmitter to the

receiver, connect a fiber optic cable to the Out LC port.

Connect the opposite end of this fiber optic cable to

the Port A In LC port on the receiver or to any other

compatible Extron FOX3 device.

2

Port A In (optional) — For one-way serial

communications from the receiver to the transmitter,

connect a fiber optic cable to the In LC port.

Connect the opposite end of this fiber optic cable to

the Port A Out LC port on a receiver or to any other

compatible Extron FOX3 device.

SFP Link LEDs —

Receiver

T

ransmitter

11

22

11

A

OUTIN

OUTPUTS

B

OUTIN

A

OUTIN

INPUTS

B

OUTIN

Figure 5. Connection

• Transmit Optical OUT LED lights solid green when powered and lights off when

there is no power on the endpoint.

• Receive Optical IN LED lights solid green when light is present and lights off

when there is no power or light present.

J

Reset button — Initiates three levels of resets (1, 4, and 5). Use a pointed stylus,

ballpoint pen, or small screwdriver to access the recessed button (see Reset on

page12 for detailed reset information).

5

FOX3 T 201 Transmitter • Installation and Operation 10

Connector and Cable Details

HDMI Connectors

HDMI signals run at a very high frequency and are especially prone to errors caused by bad

video connections, too many adapters, or excessive cable length. To avoid the loss of an

image or jitter, follow these guidelines:

• Limit or avoid the use of adapters.

• Use only cables specifically intended for HDMI or DVI signals.

To securely fasten an HDMI cable to a device:

1. Plug the HDMI cable into the panel connection (see figure6,

1

).

3

33

11

44

55

22

Figure 6. Installing the LockIt Lacing Bracket

2. Loosen the HDMI connection mounting screw from the panel enough to allow the

LockIt lacing bracket to be placed over it (

2

). The screw does not have to be removed.

3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then

tighten the screw to secure the bracket (

3

).

ATTENTION:

• Do not overtighten the HDMI connector mounting screw. The shield to which it

fastens is very thin and can easily be stripped.

• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel

elle est attachée est très fin et peut facilement être dénudé.

4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing

bracket (

4

).

5. While holding the connector securely against the lacing bracket, use pliers or similar

tools to tighten the tie wrap, then remove any excess length (

5

).

6

FOX3 T 201 Transmitter • Installation and Operation 11

RS-232 and IR

Figure 7 shows how to wire the Control (RS-232 and IR) connector.

TxRx

RxTx

Gnd

IR Device

RS-232 Device

RxTx RxTxG

RS-232 IR

CONTROL

Figure 7. Control and Sync Connectors Wiring

NOTE: The IR Tx and Rx line pair and the RS-232 Tx and Rx line pair must each cross

once between this connector and the source or destination.

TP Cable Termination and Recommendations

It is vital that your Ethernet cable be the correct cable type and that it be properly terminated

with the correct pinout. Ethernet links use Category (CAT) 3, 5e, or CAT 6, unshielded

twisted pair (UTP) or shielded twisted pair (STP) cables, terminated with RJ-45 connectors.

Ethernet cables are limited to a length of 328 feet (100 meters).

NOTES:

• Do not use standard telephone cables. Telephone cables do not support Ethernet

or Fast Ethernet.

• Do not stretch or bend cables. Transmission errors can occur.

The cable used depends on your network speed. The unit supports

10 Mbps (10Base-T — Ethernet), 100 Mbps (100Base-T — Fast Ethernet), and

1000Mbps(1000Base-T — IEEE 802.3ab) half-duplex and full-duplex Ethernet

connections.

• 10Base-T Ethernet requires CAT 3 UTP or STP cable at minimum.

• 100Base-T Fast Ethernet requires CAT 5e UTP or STP cable at minimum.

• 1000Base-T Gigabit Ethernet requires CAT 5, CAT 5e, CAT 6, or CAT 7 UTP or STP

cable.

The Ethernet cable must be terminated as a patch (straight-through) cable and must be

properly terminated in accordance with the TIA/EIA T568-B wiring standard (see figure8).

5

1

2

3

6

7

8

4

Side

12345678

Insert

Twisted

Pair Wires

Pins:

RJ-45

Connector

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIA T

568 B

Figure 8. RJ-45 Connector and Pinout Tables

7

8

FOX3 T 201 Transmitter • Installation and Operation 12

Front Panel Features

FOX3 T 201

CONFIG

INPUT

SIGNAL

HDCP

DIGITAL AUDIO

ANALOG AUDIO

A

A C

C

CB

B

Figure 9. Transmitter Front Panel Features

A

Power LED — The unit is receiving power and is operational.

B

Configuration port — This USB mini-B port is used to configure the unit and to

update firmware.

C

Input LEDs

• Signal — Lights when the unit detects an input video signal.

• HDCP — Lights when the input signal is HDCP encrypted.

• Digital Audio — Lights when digital audio is selected.

• Analog Audio — Lights when analog audio input is selected.

Operation

After the transmitter, receiver, and the connected devices are powered up, the system is fully

operational. If any problems are encountered, ensure all cables are routed and connected

properly.

NOTE: Ensure that the video source and display are properly connected to the FOX3

transmitter and receiver, and power is applied to the FOX3 devices and the display

before power is applied to the video source. If the other devices are not turned on

before the video source, the image may not appear.

Configuration and operation of the transmitter is accomplished via SIS Configuration

and Control starting on page17, the Internal Web Page starting on page35, and

Configuration Software starting on page26.

Reset

The rear panel Reset button initiates three levels of resets (numbered 1, 4, and 5). Use a

pointed stylus, ballpoint pen, or small screwdriver to access the recessed button.

See the Reset Modes and figure10 on page13 for a summary of the resets.

ATTENTION:

• Review the reset modes carefully. Some reset modes delete all user loaded

content and revert the device to default configuration.

• Analysez minutieusement les différents modes de réinitialisation. Certains modes

de réinitialisation suppriment l’intégralité du contenu chargé de l’utilisateur et

remettent l’appareil au mode de configuration par défaut.

9

La page charge ...

Extron electronics FOX3 T 201 Manuel utilisateur

Extron electronics FOX3 T 201 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents