Winmate 7” S-Series Guide de démarrage rapide

Please read these instructions carefully before using this product, and save this manual for future use.

7” S-Series HMI

W07IB3S-PCM1AC

W07IB3S-PCM1

Quick Start Guide

V1.2

For more information on this and other Winmate

products, please visit our website at:

www.winmate.com

Document Part Number: 9152070I1002

ii

FCC Statement

This device complies with part 15 FCC rules.

Operation is subject to the following two conditions:

 This device may not cause harmful interference.

 This device must accept any interference received

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

class "B" digital device, pursuant to part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at him own expense.

European Union

Electromagnetic Compatibility Directive (2014/30/EU)

 EN55024: 2010/ A1: 2015

o IEC61000-4-2: 2009

o IEC61000-4-3: 2006+A1: 2007+A2: 2010

o IEC61000-4-4: 2012

o IEC61000-4-5: 2014

o IEC61000-4-6: 2014

o IEC61000-4-8: 2010

o IEC61000-4-11: 2004

 EN55032: 2012/AC:2013

 EN61000-3-2:2014

 EN61000-3-3:2013

Low Voltage Directive (2014/35/EU)

 EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013

This equipment is in conformity with the requirement of the following EU

legislations and harmonized standards. Product also complies with the

Council directions.

iii

Copyright Notice

No part of this document may be reproduced, copied, translated, or transmitted in

any form or by any means, electronic or mechanical, for any purpose, without the

prior written permission of the original manufacturer.

Trademark Acknowledgement

Brand and product names are trademarks or registered trademarks of their

respective owners.

Disclaimer

Winmate Inc. reserve the right to make changes, without notice, to any product,

including circuits and/or software described or contained in this manual in order

to improve design and/or performance. We assume no responsibility or liability

for the use of the described product(s) conveys no license or title under any

patent, copyright, or masks work rights to these products, and make no

representations or warranties that these products are free from patent, copyright,

or mask work right infringement, unless otherwise specified. Applications that are

described in this manual are for illustration purposes only. We make no

representation or guarantee that such application will be suitable for the specified

use without further testing or modification.

Warranty

Winmate Inc. warranty guarantees that each of its products will be free from

material and workmanship defects for a period of one year from the invoice date.

If the customer discovers a defect, we will, at his/her option, repair or replace the

defective product at no charge to the customer, provide it is returned during the

warranty period of one year, with transportation charges prepaid. The returned

product must be properly packaged in its original packaging to obtain warranty

service. If the serial number and the product shipping data differ by over 30 days,

the in-warranty service will be made according to the shipping date. In the serial

numbers the third and fourth two digits give the year of manufacture, and the fifth

digit means the month (e. g., with A for October, B for November and C for

December).

For example, the serial number 1W16Axxxxxxxx means October of year 2016.

iv

Customer Service

We provide a service guide for any problem by the following steps: First, visit the

website of our distributor to find the update information about the product.

Second, contact with your distributor, sales representative, or our customer

service center for technical support if you need additional assistance.

You may need the following information ready before you call:

 Product serial number

 Software (OS, version, application software, etc.)

 Description of complete problem

 The exact wording of any error messages

In addition, free technical support is available from our engineers every business

day. We are always ready to give advice on application requirements or specific

information on the installation and operation of any of our products.

v

Safety Information

WARNING! / AVERTISSEMENT!

Always completely disconnect the power cord from your chassis

whenever you work with the hardware. Do not make connections

while the power is on. Sensitive electronic components can be

damaged by sudden power surges. Only experienced electronics

personnel should open the PC chassis.

Toujours débrancher le cordon d’alimentation du chassis lorsque

vous travaillez sur celui-ci. Ne pas brancher de connections

lorsque l’alimentation est présente. Des composantes

électroniques sensibles peuvent être endommagées par des sauts

d’alimentation. Seulement du personnel expérimenté devrait ouvrir

ces chassis.

CAUTION/ATTENTION

Always ground yourself to remove any static charge before

touching the CPU card. Modern electronic devices are very

sensitive to static electric charges. As a safety precaution, use a

grounding wrist strap at all times. Place all electronic components

in a static-dissipative surface or static-shielded bag when they are

not in the chassis.

Toujours verifier votre mise à la terre afin d’éliminer toute charge

statique avant de toucher la carte CPU. Les équipements

électroniques moderns sont très sensibles aux décharges

d’électricité statique. Toujours utiliser un bracelet de mise à la

terre comme précaution. Placer toutes les composantes

électroniques sur une surface conçue pour dissiper les charge, ou

dans un sac anti-statique lorsqu’elles ne sont pas dans le chassis.

vi

CONTENTS

INTRODUCTION 7

Features 7

Package Contents 8

Product Overview 10

GETTING STARTED 11

Turning On Your Device 11

Operating the HMI Device 12

Hot Tab Menu 12

Utilities 12

Brightness 13

Volume 13

Testing LED Light Bar 14

Performance 14

Touch Lock 14

Using Front Camera 15

Camera Interface 15

Shooting Photos 16

Recording Videos 17

Camera Settings 18

Turning Off Your Device 19

INSTALLATION 20

Wiring Requirements 20

Connecting to Other Devices 21

Power Input Connector 21

Serial Port Connector 21

RJ45 Connector 21

USB A Type Connector 22

Mounting 23

Panel Mounting 23

VESA Mounting 24

Glass Wall Mounting 28

SPECIFICATIONS 29

APPENDIX 31

Appendix A: Cleaning the Monitor 31

Appendix B: Winmate Software Development Kit 32

Winmate Download Center 32

Winmate File Share 32

7

INTRODUCTION

Congratulations on purchasing Winmate® 7” S-Series HMI. Interactive and smart

automation systems of intelligent buildings are in a fast growing phase.

Winmate® multi-touch S-Series HMI is suitable for home automation and room

management systems. Flat surface is easy-to-clean and delivers aesthetically

pleasing look for any interior. By connecting to centralized database, it can

provide real time update for booking status and available schedule, or perform as

a synchronous display in meetings.

Winmate® 7” S-Series HMI powered by Intel® Celeron® N2930 processor and

support Windows 10 IoT, Windows Embedded 8.1 Industry Pro, Windows

Embedded 8 Standard, and Windows Embedded Standard 7 – WS7P operating

systems. The HMI device features P-Cap touch-screen. In addition, the HMI

device model supports an exceptional feature - LED Light Bar. With the help of

red, green, blue and orange LED indicators you can see the status of the

machine or processes afar. It significantly reduces power consumption by

keeping the display turned off.

Features

Winmate® 7” S-Series HMI features:

 7”, 1024 x 600 with Projected Capacitive Multi-Touch P-CAP) touchscreen

 Intel® Celeron® N2930 1.83GHz

 Fanless cooling system and Ultra-low power consumption

 Front IP65 water and dust proof, rear IP22

 Dual Gigabit Ethernet

 RGB LED Status Light Bar

 Optional 2MP Front Camera

 Stylish design for room booking, access control and room information

applications

8

Package Contents

Carefully remove the box and unpack your device. Please check if all the items

listed below are inside your package. If any of these items are missing or

damaged contact us immediately.

Standard factory shipment list:

7” HMI Device

Quick Start Guide

(Hardcopy)

Driver CD & User

Manual

Varies by product

specifications

9152070I1002

IB32: 9171111I101Y

AC Adapter

(12V/ 50W)

Power Cable

VESA Plate

75 x 75 mm

922D050W12VA

Varies by country

82W70J17Y700

VESA Mounting

Screws

913511101145

9

Package may include optional accessories based on your order:

VESA Desk Stand

PCVS-V1

VESA Desk Stand

LA-100

VESA Wall Mount

Bracket

LA-106

99KK00A0000E

9B0000000128

9B0000000412

Glass Wall Mount Kit

Right: PCGM-V1L

Left: PCGM-V1L

Right: 99KN00A00013

Left:99KN00A00012

10

Product Overview

No.

Description

No.

Description

󰈆

RJ-45 (LAN)

󰈋

1 Watt Speaker

󰈇

USB 3.0, USB 2.0

󰈌

2MP Front Camera (Optional)

󰈈

RS-232/422/485

󰈍

RGB LED Light Bar

(W07IB3S-PCM1AC only)

󰈉

12V DC Terminal Block

⑨

HF RFID Reader (Optional)

󰈊

RJ-45 (LAN/ PoE)

*Note: RGB LED light bar only available for the model number W07IB3S-PCM1AC

11

GETTING STARTED

Turning On Your Device

Follow the following steps to turn on your device:

1. Connect the AC adapter to the DC-in jack connector on the back side of the

HMI device.

2. Connect the power cord to AC adapter.

3. Plug the power cord to the AC outlet and the device will turn on

automatically.

CAUTION

Use only the AC adapter included in your package

(Rating: Output 4.2 A). Using other AC adapters may damage the

device.

ALTERNATING CURRENT

This product must be grounded. Use only a grounded AC outlet.

Install the additional PE ground wire if the local installation

regulations require it.

12

Operating the HMI Device

Winmate® 7” S-Series HMI comes with HoT Tab, which allows you to operate the

HMI device.

Hot Tab Menu

To open the Hot Tab menu:

1. Double-click the Hot Tab icon

on the Windows desktop.

2. The Hot Tab main menu will

appear on the screen as shown

below.

NOTE:

RFID and LED Light Bar are optional features and may not be present

in your model.

Utilities

Utilities category allows automatically changing

orientation from landscape to portrait mode or rotating

the desktop to a different degree as 0°, 90°, 180°, and

270°.

13

Brightness

Tap Brightness button to show current brightness level.

To reduce the brightness, drag by touch this icon to the left.

To enhance the brightness, drag by touch this icon to the right.

Tap Close icon to save the changes and exit the interface.

Volume

Tap Volume button to show current brightness level.

To decrease the volume, drag by touch this icon to the left.

To increase the volume, drag by touch this icon to the right.

Tap Close icon to save the changes and exit the interface.

14

Testing LED Light Bar

Tap Light Bar to access the LED

light bar control panel, and select

Red / Green / Blue/ Orange color to

be displayed on the LED Bar.

Performance

User can adjust the performance level of the HMI device. There are four options

available:

 Extreme performance

 Office Document

 High performance

 Power Saving

Touch Lock

To LOCK touch screen, double-click the Hot Tab icon on the Windows

desktop, and tap Touch Lock.

To UNLOCK the touch screen, tap button to the right.

15

Using Front Camera

Your device might have built-in camera based on your order.

Camera Interface

Perform one of the following to open the camera:

1. Press the F1 key.

2. Tap then double-tap to display the HotTab screen. Select Camera.

No

Item

Description

1

Video

Tap to record videos

2

Photo

Tap to capture photos

3

Settings

Tap to select the destination folder to save

captured photos and videos, enable preview, and

select picture resolution and quality

4

Close

Tap to close the camera

5

Capture Screen

Shows the object to capture

16

Shooting Photos

To make a photo:

1. Open the Camera.

2. Focus on the object.

3. Tap to capture the object.

4. By default, the photo preview is displayed briefly on the screen.

The preview screen automatically closes after 3 seconds. Alternatively, do

one of the following:

- Tap to delete the photo and return to the camera screen.

- Tap to close the preview and return to the camera screen.

17

Recording Videos

To record a video:

1. Open the Camera.

2. Focus on the object.

3. Tap to record the video. The video recording screen appears

.

4. Tap to stop recording and return to the camera screen.

5. To playback the video, browse for the video file and play using a media

player application on your device.

18

Camera Settings

1. Tap to open the setting page

2. Modify necessary settings.

No

Item

Description

1

Preview Setting

Check one of the check boxes to show the

preview screen right after capturing a photo.

• Show Preview: Check this box and enter the

preview duration on Close preview after.

When the duration ends, the preview screen will

automatically close.

• Always Show Preview: When this box is

checked, the preview screen will only close

when you tap the return button ( ).

2

Picture Save

Tap this button to browse for the folder directory

where you want to save captured photos.

3

Video Save Folder

Tap this button to browse for the folder directory

where you want to save recorded videos.

4

Picture Resolution

Select the picture resolution:

• 640 x 480

• 1600 x 1200

5

Picture Quality

Select the picture quality: Low, Medium, High,

Best.

3. When settings are complete, tap OK to apply and save change.

19

Turning Off Your Device

You can Turn OFF the HMI device with the Windows power settings.

To shut down the device:

1. Tap Start >Shut down.

2. Wait for your HMI device to completely turn off before disconnecting the

power cord (if necessary).

20

INSTALLATION

Wiring Requirements

The following common safety precautions should be observed before installing

any electronic device:

 Strive to use separate, non-intersecting paths to route power and

networking wires. If power wiring and device wiring paths must cross make

sure the wires are perpendicular at the intersection point.

 Keep the wires separated according to interface. The rule of thumb is that

wiring that shares similar electrical characteristics may be bundled together.

 Do not bundle input wiring with output wiring. Keep them separate.

 When necessary, it is strongly advised that you label wiring to all devices in

the system.

CAUTION

 Do not run signal or communication wiring and power wiring in the same

conduit. To avoid interference, wires with different signal characteristics

(i.e., different interfaces) should be routed separately.

 Be sure to disconnect the power cord before installing and/or wiring your

device.

 Verify the maximum possible current for each wire gauge, especially for the

power cords. Observe all electrical codes dictating the maximum current

allowable for each wire gauge.

 If the current goes above the maximum ratings, the wiring could overheat,

causing serious damage to your equipment.

 Be careful when handling the unit. When the unit is plugged in, the internal

components generate a lot of heat which may leave the outer casing too

hot to touch.

La page est en cours de chargement...

Winmate 7” S-Series Guide de démarrage rapide

Ce manuel convient également à

Winmate 7” S-Series Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents