Eurotech DynaGATE 10-12 Le manuel du propriétaire

User Manual

DynaGATE 10-12-3x

Automotive IoT Edge Gateway TI AM335x, LTE Cat 1

Rev. 2-0 — 15 July 2019 — DYGATE-10-12-3x_Man_ENG_2-0 — ENGLISH

Trademarks

All trademarks, registered trademarks, logos, trade names, products names contained in this document

are the property of their respective owners.

Intended audience of this document

This document is intended for system integrators: skilled persons with a thorough knowledge in linking

together, physically or functionally, different computing systems and software applications to operate as a

coordinated whole in compliance with the applicable regulations.

Revision history

Revision Description Date

1-0 First release 19 December 2018

2-0 General contents update 15 July 2019

DynaGATE 10-12 User Manual Rev. 2-0 How to get started

HOW TO GET STARTED

To get started with the DynaGATE 10-12, follow these steps:

1. Read carefully and understand the instructions and warnings contained in this manual.

To lower the risk of personal injury, electric shock, fire or damage to equipment, observe the

instructions and warnings contained in this manual.

For more information see: "Safety instructions" on page9.

Whenever in doubt regarding the correct understanding of this document, contact the Eurotech

Technical Support.

For more information see: "How to receive technical assistance" on page13

2. Know the DynaGATE 10-12 interfaces.

For more information see:

l "Product overview" on page19

l "Technical specifications" on page21

l "Interfaces overview" on page31

l "Interfaces in detail" on page37

3. Understand how to login the Administration Console and how to manage the interfaces in

Linux.

For more information see:

l "How to log in the Administration Console" on page59

l "How to manage the interfaces in Linux" on page61

4. Install the DynaGATE 10-12.

For more information see:

l "Mechanical specifications" on page83

l "How to install the product" on page85

5. Supply power to the DynaGATE 10-12.

For more information see: "Power supply. How to turn on/off and reset the product" on page87

6. Start developing your IoT applications.

The DynaGATE 10-12 supports the Eurotech Everyware Software Framework (ESF). ESF is a

smart application container that enables remote management of IoT gateways and provides a wide

range of APIs allowing you to write and deploy your own IoT application.

For more information see:

l "Eurotech Everyware IoT" on page79

l http://esf.eurotech.com/docs.

3 / 100

(This page has been intentionally left blank)

DynaGATE 10-12 User Manual Rev. 2-0 Contents

CONTENTS

Trademarks 2

Intended audience of this document 2

Revision history 2

How to get started 3

Contents 5

1 Safety instructions 9

1.1 Warning messages used in this document 9

1.1.1 Warning messages for harm to persons 9

1.1.2 Warning messages for damage to property 10

1.2 Warning: power supply safety 10

1.3 Caution: wireless safety 10

1.4 Caution: product's surfaces may become hot 10

2 Consignes de securite 11

2.1 Messages d’avertissement utilisés dans ce document 11

2.1.1 Messages d’avertissement relatifs au dommage aux personnes 11

2.1.2 Messages d’avertissement relatifs aux dommages matériels 12

2.2 Avertissement: sécurité de l’alimentation électrique 12

2.3 Attention: sécurité sur la connectivité sans fil 12

2.4 Attention: les surfaces du produit peuvent devenir chaudes 12

3 How to receive technical assistance 13

3.1 How to ask for technical support 13

3.2 How to send a product for repair 13

4 Comment obtenir une assistance technique 15

4.1 Comment contacter le support technique 15

4.2 Comment retourner un produit en service après vente 15

5 Conventions used in this document 17

5.1 Conventions for signal names 17

5.2 Conventions for signal types 17

6 Product overview 19

6.1 Product description 19

6.2 Intended use and not allowed uses of the product 20

6.2.1 Intended use 20

6.2.2 Not allowed uses 20

6.3 Technical specifications 21

6.4 Optional accessories 23

6.5 Product labels 24

7 Norms and certifications 25

7.1 CE marking 25

7.2 Directive RED 2014/53/EU 25

7.2.1 Modification statement 25

7.3 FCC marking 25

7.4 FCC/ISEDregulatory notices 25

7.4.1 Modification statement 25

7.4.2 ISED Canada regulatory notices 25

7.4.3 RF radiation exposure statement 27

7.4.4 FCC class B digital device notice 27

5 / 100

Contents DynaGATE 10-12 User Manual Rev. 2-0

7.4.5 ISED class B digital device notice 27

7.4.6 Labeling information 27

7.5 Restrictions on 5 GHz Wi-Fi usage 29

7.5.1 EU Restrictions on 5 GHz Wi-Fi Usage 29

7.5.2 FCC Restrictions on 5 GHz Wi-Fi Usage 29

7.6 Antennas list 30

7.7 RoHS 3 compliance 30

7.8 REACH compliance 30

7.9 WEEE compliance 30

8 Interfaces overview 31

8.1 Front Side Interfaces overview 31

8.2 Rear Side Interfaces overview 32

8.2.1 Service Panel Interfaces 33

8.3 Right Side Interface overview 34

8.4 Left Side Interface overview 35

8.5 LED Indicators overview 36

9 Interfaces in detail 37

9.1 Wi-Fi and Bluetooth (vers: -32, -35, -36) 37

9.1.1 Wi-Fi specifications 37

9.1.1.1 2.4 GHz TX output power 37

9.1.1.2 5 GHz TX output power 37

9.1.2 Bluetooth specifications 38

9.1.3 BLE specifications 38

9.1.4 Antennas connectors specifications 38

9.2 Internal mobile connectivity (vers: -33, -34, -35, -36) 39

9.2.1 Internal modem specifications (according to product versions) 39

9.2.1.1 Product features 39

9.2.1.2 LTE data 39

9.2.1.3 Supported RF bands 39

9.2.1.4 TX output power 39

9.2.2 LTE - single antenna operation notes 39

9.2.2.1 Main antenna requirements 40

9.2.2.2 Second antenna requirements (for antenna diversity) 41

9.2.3 Antennas connectors specifications 42

9.2.4 The MicroSIM card holders 43

9.2.4.1 How to insert / remove the MicroSIM card 43

9.3 Internal GNSS 45

9.3.1 Internal GNSS specifications 45

9.3.2 Internal GNSS antenna connector specifications 45

9.4 Digital I/Os 46

9.4.1 Insulated Digital Inputs 46

9.4.1.1 Electrical specifications 46

9.4.1.2 Electrical schematics 46

9.4.2 Insulated Digital Outputs 47

9.4.2.1 Electrical specifications 47

9.4.2.2 Electrical schematics 47

9.4.3 Digital I/Os connector specifications 47

9.5 COM 0 and COM 1 48

9.5.1 Note for termination resistors (only for RS-485 mode) 48

9.5.2 Note for fail safe resistors (only for RS-485 mode) 48

9.5.2.1 Switches meaning 48

9.5.3 COM 0 and COM 1 connector specifications 49

9.6 CAN 0 and CAN 1 50

9.6.1 CAN 0 and CAN 1 connector specifications 50

6 / 100

DynaGATE 10-12 User Manual Rev. 2-0 Contents

9.7 ETH 0 and ETH 1 51

9.7.1 Ethernet specifications 51

9.7.2 ETH 0 and ETH 1 connectors specifications 51

9.8 USB 0, USB 1, USB 2 52

9.8.1 USB 0 and USB 1 connectors specifications 52

9.8.2 USB 2 connector specifications 52

9.9 Expansion connector 53

9.9.1 Expansion connector specifications 53

9.10 TTL Serial Console 54

9.10.1 TTL Serial console connector specifications 54

9.11 The MicroSD card holder 55

9.11.1 How to insert / remove the MicroSD card in the holder 55

9.12 RTC (Real Time Clock) 56

9.12.1 The RTC device "/dev/rtc1" 56

9.12.2 The RTC backup supercap 56

9.13 Watchdog 56

9.14 Accelerometer 56

9.15 Programmable pushbutton 56

10 The Software 57

10.1 The Linux OS distribution 57

10.2 The bootloader procedure 57

10.3 How to create and use a bootable micro SD card for a Linux release 57

11 How to log in the Administration Console 59

11.1 Default credentials 59

11.2 How to login using the Serial Console 59

11.3 How to Login Via Secure Shell (SSH) 59

11.3.1 How to Login Via eth0 60

11.3.2 How to Login via eth1 60

11.4 How to change the password 60

12 How to manage the interfaces in Linux 61

12.1 How to drive the GPIOs: the GPIO utility 61

12.2 How to know which version of Linux is installed 62

12.3 How the storage memory is exposed 62

12.4 How to manage Wi-Fi and Bluetooth 62

12.5 How to manage the Internal Cellular Modem 63

12.5.1 How to select the MicroSIM slot to use 63

12.5.2 Note for LE910-NA1 cellular modem: AT&T / Verizon firmware support 63

12.5.2.1 How to select the AT&T firmware 64

12.5.2.2 How to select the Verizon firmware 64

12.5.3 How to disable/enable the diversity (CELL DIV) function 64

12.6 How to manage the Internal GNSS 65

12.7 How to manage the CAN ports 66

12.7.1 How to enable the CAN bus 5V 66

12.7.2 How to setup a CAN port 66

12.7.3 How to send/receive a message via a CAN port 66

12.8 How the TTL Serial Console is exposed 66

12.9 How to manage the COM ports 67

12.9.1 How to set the RS-232/485 modes 67

12.9.1.1 How to use the ethsetserial utility to configure the COM ports 67

12.9.1.2 How to implement the ioctl in the source code to configure the COM ports 68

12.9.2 How to test a serial port 70

12.10 How to manage the Digital I/Os 71

12.11 How to manage the LED Indicators 71

7 / 100

Contents DynaGATE 10-12 User Manual Rev. 2-0

12.12 How the Ethernet ports are exposed 71

12.13 How to enable the 3.3V and 5V power supply on the Expansion connector 72

12.14 How the RTC is exposed 73

12.15 How the Watchdog is exposed 74

12.15.1 How to manage the watchdog using the C programming language 74

12.15.2 How to manage the watchdog from the command line 74

12.15.3 For more information 75

12.16 How to output the Accelerometer values 75

12.17 How to read the Internal Temperature Sensor 76

12.18 How to know the programmable pushbutton status 76

12.19 Optional: How to manage the ReliaCELL power supply 76

13 How to compile custom software 77

13.1 How to set up the toolchain 77

13.2 How to use the toolchain to compile custom software 77

14 Eurotech Everyware IoT 79

14.1 Everyware Software Framework (ESF) 79

14.2 The ESF Web UI 80

14.3 The ESF Wires application 81

14.4 Everyware Cloud (EC) 82

14.5 For more information 82

15 Mechanical specifications 83

15.1 Product mechanical dimensions 83

16 How to install the product 85

16.1 How to install the product 85

17 Power supply. How to turn on/off and reset the product 87

17.1 Power supply specifications 87

17.2 Power IN connector specifications 87

17.3 How to supply power and turn ON the product 88

17.4 How to turn OFF the product 89

17.5 How to reduce the power consumption of the product 89

17.6 How to hardware reset the product 89

18 How to maintain the product 91

18.1 How to safely remove the power supply 91

18.2 How to verify the installation of the product 91

18.3 How to clean the product 91

Appendix 1: Advanced boot options 93

1.1 Advanced boot options 93

1.1.1 How to configure a boot option 93

1.1.2 How to gain access to the bootloader CLI 93

1.1.3 How to change the default boot option 94

1.2 The Production fitImage 94

1.2.1 How to define the variants 94

1.2.2 How to manually configure the system to boot from a different DTB within the current fitImage 94

Appendix 2: Expansion connector pin map with respect to device tree pin assignment 97

Notes 99

8 / 100

DynaGATE 10-12 User Manual Rev. 2-0 1 Safety instructions

1 SAFETY INSTRUCTIONS

IMPORTANT: Read carefully and understand the instructions and warnings contained in this

document before installing / using the product. Keep this document for future reference.

To lower the risk of personal injury, electric shock, fire or damage to equipment, observe the instructions

and warnings contained in this document.

Failure to comply with the instructions and warnings contained this document, violates the standards of

safety, design, manufacture, and intended use of the product.

Eurotech assume no liability for any damage caused by failure to observe the instructions and warnings

contained this document.

Whenever you have any doubt regarding the correct understanding of this document, contact the Eurotech

Technical Support (for more information see "How to receive technical assistance" on page13).

1.1 Warning messages used in this document

1.1.1 Warning messages for harm to persons

To indicate an imminently hazardous situation which, if not avoided, will result in death or

serious injury, the following message is used:

DANGER

Sign

(if necessary)

TEXT THAT EXPLAINS THE HAZARD AND THE CONSEQUENCES OF NOT

AVOIDING IT

Text that explains how to avoid this hazard

To indicate a potentially hazardous situation which, if not avoided, could result in death or

serious injury, the following message is used:

WARNING

Sign

(if necessary)

TEXT THAT EXPLAINS THE HAZARD AND THE CONSEQUENCES OF NOT

AVOIDING IT

Text that explains how to avoid this hazard

To indicate a potentially hazardous situation which, if not avoided, could result in minor or

moderate injury, the following message is used:

CAUTION

Sign

(if necessary)

TEXT THAT EXPLAINS THE HAZARD AND THE CONSEQUENCES OF NOT

AVOIDING IT

Text that explains how to avoid this hazard

9 / 100

1 Safety instructions DynaGATE 10-12 User Manual Rev. 2-0

1.1.2 Warning messages for damage to property

To indicate potential risks of damage to the supported product (or to other property), the

following message is used:

NOTICE

Sign

(if necessary)

Text that explains how to avoid damaging the supported product (or other

property)

1.2 Warning: power supply safety

WARNING

ELECTRIC SHOCK HAZARD

Failure to supply power correctly or to follow all operating instructions correctly, may create an

electric shock hazard, which could result in personal injury or loss of life, and / or damage the

equipment or other property.

To avoid injuries and safely supply power to the product, complete the following steps:

1. Observe all the instructions for safety, installation, and operation

2. Make sure your hands are dry

3. Make sure that all the cables used:

a. Are in good condition before using them

b. Meet the product requirements and comply with the relevant standards and

regulations

4. Position cables with care. Do not position cables in places where they may be trampled

or compressed by objects placed on them

5. Make sure that the power-points and plugs are in good condition before using them

6. Do not overload the power-points and plugs

7. Make sure that the product maintains a proper grounding connection

8. Use a power supply that meets the product requirements and complies with the relevant

standards and regulations. In case of uncertainties, contact the Eurotech Technical

Support Team (for more information see "How to receive technical assistance" on

page13)

9. Connect power after the installation of the system has been completed

10. Never connect or disconnect the cables with the system or the external apparatus

switched ON.

1.3 Caution: wireless safety

The antennas used in the product have to be installed with care, to avoid any interference with

other electronic devices and to guarantee a minimum distance from the body (20 cm). In case of

this requirement cannot be satisfied, the system integrator has to assess the final product against

the SAR regulations.

1.4 Caution: product's surfaces may become hot

Depending on the operating environment temperature, product's surfaces may become hot, creating a burn

hazard. Always allow the product's surfaces to cool before touching them.

10 / 100

DynaGATE 10-12 User Manual Rev. 2-0 2 Consignes de securite

2 CONSIGNES DE SECURITE

IMPORTANT: Lire attentivement et bien respecter les instructions et les avertissements contenus

dans ce document avant d'installer / d'utiliser le produit. Conserver ce document pour s'y référer

à l'avenir.

Pour éviter les risques de blessures, de choc électrique, d'incendie ou de détérioration du matériel, bien

suivre les instructions et les avertissements contenus dans ce document.

Le non-respect des instructions et des avertissements contenus dans ce document constitue une violation

des normes de sécurité, de conception, de fabrication et d'utilisation prévue du produit.

Eurotech rejette toute responsabilité pour les dommages causés en cas de non-respect des instructions et

des avertissements contenus dans ce document.

En cas de doute sur la compréhension de ce document, contacter le Support Technique d’ Eurotech (pour

plus d’informations voir "Comment obtenir une assistance technique" page 15).

2.1 Messages d’avertissement utilisés dans ce document

2.1.1 Messages d’avertissement relatifs au dommage aux personnes

Pour signaler une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort

ou un préjudice grave le message suivant est utilisé:

DANGER

Signal

(si besoin)

TEXTE EXPLIQUANT LE DANGER ET SES CONSÉQUENCES

Texte expliquant comment éviter ce danger

Pour signaler une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait

entraîner la mort ou un préjudice grave le message suivant est utilisé:

AVERTISSEMENT

Signal

(si besoin)

TEXTE EXPLIQUANT LE DANGER ET SES CONSÉQUENCES

Texte expliquant comment éviter ce danger

Pour signaler une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait

entraîner un préjudice mineur ou modéré le message suivant est utilisé:

ATTENTION

Signal

(si besoin)

TEXTE EXPLIQUANT LE DANGER ET SES CONSÉQUENCES

Texte expliquant comment éviter ce danger

11 / 100

2 Consignes de securite DynaGATE 10-12 User Manual Rev. 2-0

2.1.2 Messages d’avertissement relatifs aux dommages matériels

Pour signaler les risques potentiels de détérioration du produit (ou des produits annexes), le

message suivant est utilisé:

AVIS

Signal

(si besoin)

Texte expliquant comment éviter d'endommager le produit (ou des produits

annexes)

2.2 Avertissement: sécurité de l’alimentation électrique

AVERTISSEMENT

RISQUE DE CHOC ÉLECTRIQUE

Une alimentation électrique incorrecte peut créer un risque de choc électrique, pouvant

entraîner des blessures corporelles ou la perte de vies humaines, et / ou endommager le

produit ou d'autres biens.

Pour éviter les blessures et brancher l'appareil en toute sécurité, procéder comme suit:

1. Respecter toutes les consignes de sécurité, d'installation et d'utilisation

2. S'assurer que les mains sont sèches

3. S'assurer que tous les câbles utilisés:

a. Sont en bon état avant leur utilisation

b. Répondent aux exigences du produit et soient conformes aux normes et

réglementations en vigueur

4. Positionner les câbles avec soin. Ne pas les placer dans des endroits où ils risquent

d'être piétinés ou comprimés par des objets

5. S’assurer que les prises de courant et les connecteurs d’alimentation sont en bon état

avant de les utiliser

6. Ne pas surcharger les prises de courant et les connecteurs d’alimentation

7. S'assurer que le produit est correctement relié à la terre

8. Utiliser une alimentation électrique conforme aux exigences du produit et conforme aux

normes et réglementations en vigueur. En cas d'incertitude, contacter l'équipe

d'assistance technique d'Eurotech (pour plus d'informations, voir "Comment obtenir une

assistance technique" page 15)

9. Ne Brancher l'alimentation électrique qu’une fois l'installation du système terminée

10. Ne jamais brancher ou débrancher les câbles lorsque le système ou un appareil

périphérique sous tension.

2.3 Attention: sécurité sur la connectivité sans fil

Les antennes utilisées dans le produit doivent être installées avec soin et à une distance

minimale de 20 cm de tout autre appareil électronique afin d'éviter toute interférence. Si cette

exigence ne peut être satisfaite, l'intégrateur de système doit évaluer le produit final par rapport à

la réglementation DAS.

2.4 Attention: les surfaces du produit peuvent devenir chaudes

Selon la température ambiante lors de l’utilisation, les surfaces du produit peuvent devenir brûlantes,

engendrant un risque de brûlure. Laisser toujours les surfaces du produit refroidir avant de les

toucher.

12 / 100

DynaGATE 10-12 User Manual Rev. 2-0 3 How to receive technical assistance

3 HOW TO RECEIVE TECHNICAL ASSISTANCE

3.1 How to ask for technical support

To ask for technical support, complete the following steps

1. Go to the Eurotech Global Support Centre: https://support.eurotech.com/

2. Submit a support request

3. Wait for the reply from the Support Team with the information you required

3.2 How to send a product for repair

Any product returned to Eurotech, that is found to be damaged due to inadequate packaging, will

not be covered by the warranty.

To send a product for repair, complete the following steps:

1. Go to the Eurotech Global Support Centre: https://support.eurotech.com/

2. Submit an RMA request

3. Wait for the reply from the RMA Department. It will contain:

l The RMA number

l The shipping information

4. Pack the product adequately using anti-static material and place it in a sturdy box with enough

packing material to protect it from shocks and vibrations

5. Ship the product to Eurotech following the information received from the RMA Department.

13 / 100

(This page has been intentionally left blank)

DynaGATE 10-12 User Manual Rev. 2-0 4 Comment obtenir une assistance technique

4 COMMENT OBTENIR UNE ASSISTANCE TECHNIQUE

4.1 Comment contacter le support technique

Pour demander un support technique, procéder comme suit:

1. Se connecter au Support Eurotech sur: https://support.eurotech.com/

2. Envoyer une demande d’assistance

3. Attendre la réponse de l'équipe de support avec les informations requises

4.2 Comment retourner un produit en service après vente

Tout produit renvoyé à Eurotech, qui se trouve endommagé en raison d'un emballage inadéquat,

ne sera pas couvert par la garantie.

Pour retourner un produit en Service Après Vente, procéder comme suit:

1. Se connecter au Support Eurotech sur: https://support.eurotech.com/

2. Faire une demande de RMA

3. Attendre la réponse du service RMA qui indiquera:

l Le numéro de RMA

l Les informations pour l’expédition

4. Emballer le produit de manière adéquate en utilisant des protections antistatiques et le placer dans

un conditionnement solide contenant suffisamment de matériau d'emballage pour le protéger des

chocs et des vibrations

5. Expédier le produit chez Eurotech selon les informations reçues par mail.

15 / 100

(This page has been intentionally left blank)

DynaGATE 10-12 User Manual Rev. 2-0 5 Conventions used in this document

5 CONVENTIONS USED IN THIS DOCUMENT

5.1 Conventions for signal names

Convention Description

GND Ground

# Active low signal

+ Positive signal; Positive signal in differential pair

- Negative signal; Negative signal in differential pair

3.3 3.3 V signal level

5 5 V signal level

NC No Connection

Reserved Use is reserved to Eurotech

5.2 Conventions for signal types

Convention Description

I Signal is an input to the system

O Signal is an output from the system

IO Signal may be input or output

P Power and Ground

A Analog signal

NC No Connection

Reserved Use is reserved to Eurotech

17 / 100

(This page has been intentionally left blank)

DynaGATE 10-12 User Manual Rev. 2-0 6 Product overview

6 PRODUCT OVERVIEW

6.1 Product description

The DynaGATE 10-12 is a family of IoT Edge Gateways designed to deliver LTE connectivity with 2G/3G

fallback to automotive and lightly rugged applications.

The DynaGATE 10-12 is based on the TI AM335x Cortex-A8 (Sitara) processor family, with 1GB of RAM,

4GB of eMMC and user-accessible MicroSD and dual Micro-SIM slots.

The DynaGATE 10-12 features the following wired connectivity capabilities: 2x Fast Ethernet, 3x Host 2.0

USB, 2x CAN bus with 5V (100mA) Power Out, 2x Optoinsulated Digital Input and 2x Optoinsulated

Digital Output; it also includes the following serial ports: 2x RS-232/485 (surge protected) and 1x TTL

Serial Console.

The DynaGATE 10-12 can also feature a wide range of wireless connectivity capabilities

1

: it can integrate

an internal LTE Cat 1 modem (2G/3G fallback) with dual Micro-SIM support, Wi-Fi, and Bluetooth Low

Energy; an internal GNSS provides precise geolocation capabilities.

All interfaces are suitable for applications with a high level of shock and vibration: front side USB ports

feature high retention connectors and all other signals are delivered by locking connectors or screw-flange

terminal blocks.

The DynaGATE 10-12 can come with Everyware Software Framework (ESF), a commercial, enterprise-

ready edition of Eclipse Kura, the open source Java/OSGi middleware for IoT Edge Gateways.

Distributed and supported by Eurotech, ESF supports ready-to-use field protocols (including Modbus,

OPC-UA, S7), MQTT connectivity, web-based visual data flow programming and deep configuration.

ESF is also integrated with Everyware Cloud (EC), Eurotech IoT Integration Platform (separately

available), enabling advanced diagnostics, provisioning, and full remote device access and management.

Used stand-alone, or in conjunction with EC, the DynaGATE 10-12 provides a fast go-to-market solution

for IoT projects of any size.

For more details visit www.eurotech.com.

Figure 6.1 - The DynaGATE 10-12

1

The features availability depends on the product versions

19 / 100

6 Product overview DynaGATE 10-12 User Manual Rev. 2-0

6.2 Intended use and not allowed uses of the product

The product is intended for professional use and must be installed by qualified personnel only.

The product must be installed in a secured location, accessible to authorized personnel only (for

example in a cabinet / technical compartment).

6.2.1 Intended use

The DynaGATE 10-12 is a family of IoT Edge Gateways designed to deliver LTE connectivity with 2G/3G

fallback to automotive and lightly rugged applications.

The DynaGATE 10-12 must:

l Be installed in a secured location, only accessible to authorized personnel (for example in a cabinet

/ technical compartment), and not exposed to atmospheric agents

l Be used indoors or in automotive applications*

l Be used with appropriate interconnecting and power cables

l Be used with an external DC power supply source that:

o

Must meet the requirements stated on the identification label of the product

o

Must deliver a maximum current of 2 A

o

Must include an external 2 A fuse on the line coming from the negative terminal

* Before using the DynaGATE 10-12, versions: -X2, -X5, -X6, in automotive applications in any EU

Member State, switch-off the Wi-Fi band: 5150 - 5350 MHz.

6.2.2 Not allowed uses

Do not use the DynaGATE 10-12:

l In railway applications

l In defence applications

l In industrial applications

l Outdoors

l In safety-critical applications

l In environments with potentially explosive atmospheres

l If not installed according to the instructions and warnings contained in this document.

When used in automotive applications in any EU Member State, do not use the DynaGATE 10-12,

versions: -X2, -X5, -X6, with the Wi-Fi band: 5150 - 5350 MHz enabled.

20 / 100

La page est en cours de chargement...

Eurotech DynaGATE 10-12 Le manuel du propriétaire

Eurotech DynaGATE 10-12 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents