Breville BES920XL Manuel utilisateur

Marque: Breville

Modèle: BES920XL

Catégorie: Cafetières

Taper: Manuel utilisateur

Ce manuel convient également à

Suits all BES920XL models

the Dual Boiler

™

Instruction Book - Manuel d’instructions

www.breville.com

Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.

Due to continued product improvement, the products illustrated/photographed

in this book may vary slightly from the actual product.

Model BES920XL Issue - G15

USA

Mail: Breville USA

19400 S. Western Ave

Torrance CA

90501-1119

Phone: 1-866-273-8455

1-866-BREVILLE

Web:

brevilleusasupport.com

Breville Consumer Support

Canada

Mail: Breville Canada

3595 boulevard Côte-Vertu,

Saint-Laurent, Québec,

H4R 1R2

Phone:

1-855-683-3535

Email:

askus@breville.ca

CONTENTS

4 Breville recommends safety ﬁrst

9 Know your Breville product

10 Operating your Breville product

23 Coffee making tips & preparation

27 Care & cleaning

31 Troubleshooting

37 Coffees to try

CONGRATULATIONS

On the purchase of your Breville product

*Registering is not a substitute for proof of purchase when submitting a Warranty Claim.

USA Consumers: www.brevilleusa.com

Canadian Consumers: www.breville.ca

and exclusive offers.

4 5

PAGE HEADER..... PAGE HEADER.....

BREVILLE RECOMMENDS SAFETY FIRSTBREVILLE RECOMMENDS SAFETY FIRST

At Breville we are very safety conscious. We design and manufacture consumer products with

the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise

a degree of care when using any electrical appliance and adhere to the following precautions.

When using electrical appliances, basic

safety precautions should always be

followed, including the following:

FOR ALL ELECTRICAL

APPLIANCES

• Carefully read all instructions

before operating and save for

future reference.

• Do not touch hot surfaces. Use

handles or knobs as advised in

this instruction book.

• To protect against ﬁre, electric

shock and injury to persons do

not immerse the power cord,

plug, or appliance itself in water

or other liquids.

• Close supervision is necessary

when any appliance is used by

or near children.

• If the appliance is to be:

- left unattended

- cleaned

- moved

- assembled; or

- stored

Always switch off the appliance

by pressing the POWER button

to off and unplug from the

power outlet.

• Always allow the appliance to

cool before cleaning, moving

or storing.

• It is recommended to regularly

inspect the appliance and power

cord. Do not use the appliance

if there is damage to the

power cord or plug, or after the

appliance malfunctions or has

been damaged in any way.

Immediately stop use and call

Breville Consumer Support.

• The use of accessory

attachments not recommended

by Breville may result in ﬁre,

electric shock or injury to

persons.

• Do not let the power cord

hang over the edge of a table

or counter-top, or touch hot

surfaces.

• Do not place the appliance

near the edge of a table or

counter-top. Ensure the surface

is level, clean and free of water

and other substances.

• Do not place the appliance on

or near a hot gas or electric

burner. Do not place it in, or

allow it to come in contact with

a heated oven.

IMPORTANT SAFEGUARDS

• Do not attempt to open or

service the espresso machine.

• For any maintenance other than

cleaning, call Breville Consumer

Support or visit a Breville

Authorized Servicer.

SHORT CORD INSTRUCTIONS

Your Breville appliance is ﬁtted

with a short power cord to reduce

personal injury or property damage

resulting from pulling, tripping

or becoming entangled with a

longer cord. Longer detachable

power cords or extension cords are

available and may be used if care

is exercised. If an extension cord is

used, (1) the marked electrical rating

of the cord set or extension cord

should be at least as great as the

electrical rating of the appliance,

(2) the cord should be arranged

so that it will not drape over the

counter-top or table where it can

be pulled on by children or tripped

over unintentionally and (3) the

extension cord must include a

3-prong grounding plug.

• This appliance is recommended

for household use only. Do not

use this appliance for anything

other than its intended use. Do

not use outdoors. Do not use in

moving vehicles or boats.

SPECIFIC INSTRUCTIONS

FOR BES920XL

• It is recommended to plug the

espresso machine into a properly

grounded and dedicated circuit,

separate from other electrical

appliances.

• Use only cold water in the

water tank. Do not use any

other liquids. Do not use highly

ﬁltered, demineralized or

distilled water as this may affect

the taste of the coffee and how

the espresso machine operates.

• Ensure the portaﬁlter is ﬁrmly

inserted and secured into the

group head before starting an

extraction. Never remove the

portaﬁlter during the extraction

process.

• Caution must be used during

descaling as hot steam may be

released. Before descaling, turn

off the machine, allow to cool

for at least 1 hour and ensure

the drip tray is empty and fully

inserted. For instructions, refer to

‘Descale (dESc).’

6 7

PAGE HEADER.....

BREVILLE RECOMMENDS SAFETY FIRST

BREVILLE ASSIST™ PLUG

Your Breville appliance comes with

a unique Assist™ Plug, conveniently

designed with a ﬁnger hole to ease

removal from the power outlet.

CSA DUTY CYCLE MARKING:

The Canadian Standards Authority

requires any appliances capable of

drawing over 1500W to be marked

with a ‘duty cycle’ in minutes. For

the BES920XL, this ‘duty cycle’

represents the maximum time for

which the appliance will draw over

1500W during any 2 hour period

of use. It does not indicate the

appliance is unsafe for continuous

use or is required to be switched

off at certain intervals during

normal use.

CALIFORNIA PROPOSITION 65:

(Applicable to California

residents only).

This product contains chemicals

known to the State of California to

cause cancer, birth defects or other

reproductive harm.

SAVE THESE INSTRUCTIONS

FEATURES OF YOUR BREVILLE PRODUCT

TRIPLE HEAT SYSTEM

Dual Stainless Steel Boilers

Dedicated espresso and steam boilers for

simultaneous milk texturing and espresso

extraction at the optimum temperature.

Actively Heated Group Head

Commercial 58mm group head with

embedded element for optimal thermal

stability during extraction.

PRECISION CONTROL

Electronic PID Temperature Control

Electronic temperature control delivers

precise water temperature for optimum

espresso ﬂavor. Programmable.

Regulated Extraction Pressure

Over pressure valve (OPV) limits maximum

pressure for optimal espresso ﬂavor.

Low Pressure Pre-Infusion

Gradually increases water pressure to gently

expand grinds for an even extraction.

Programmable.

Dual Pumps

Dedicated espresso and steam boiler

pumps help maintain constant pressure

throughout extraction.

Programmable Shot Temperature

Adjust water temperature to achieve optimal

espresso ﬂavor depending on coffee origin

and degree of roast.

ADDITIONAL FEATURES

Backlit LCD

Displays current settings and simpliﬁes

programming functions.

High Volume Instant Steam

Dedicated 32 ﬂ.oz (950ml) steam boiler

delivers instant and continuous steam.

Commercial Steam Wand

Stainless steel 360° swivel-action steam

wand with 3 hole tip for a silkier texture.

Instant Hot Water

Dedicated hot water outlet for making

Americanos and pre-heating cups.

58mm Full Stainless Steel Portaﬁlter

Helps to promote a more even extraction

and is easier to clean.

Shot Clock

Displays duration of the espresso shot

being extracted.

Auto Start

Switches machine on at a speciﬁed time.

The Razor™ Dose Trimming Tool

Patented twist blade trims down the puck

to the right level for precision dosing and

a consistent extraction.

8 9

KNOW YOUR BREVILLE PRODUCT

A. Top-ﬁll 84 ﬂ.oz (2.5L) removable

water tank

With integrated water ﬁlter and backlit

level indicator.

B. Hot water dial

Rotate to start and stop the ﬂow of hot

water from the hot water outlet.

C. POWER button

D. Backlit LCD

Displays current settings and simpliﬁes

programming functions.

E. MENU button

Use in conjunction with the LCD to set

the programmable functions.

F. Espresso pressure gauge

Monitors extraction pressure.

G. Integrated & removable 58mm tamper

H. Heated 58mm group head with

embedded element

I. 58mm full stainless steel portaﬁlter

J. Heated cup warming tray

K. 1 CUP, 2 CUP and MANUAL buttons

With preset shot durations, manual

override or reprogrammable

durations/volumes.

L. Steam lever

For instant and continuous steam.

M. Dedicated hot water outlet

Delivers hot water for Americanos and

pre-heating cups.

N. 360° swivel action steam wand

With 3 hole tip for a silkier texture.

O. Descale access point

P. Tool storage tray

Houses accessories when not in use.

Q. Drop down swivel foot

Lifts the machine upwards for easy

maneuverability.

R. Removable drip tray

With Empty Me! indicator.

KNOW YOUR BREVILLE PRODUCT

ACCESSORIES

A. Stainless steel milk jug

B. Water filter holder with ﬁlter

C. 1 CUP & 2 CUP single wall ﬁlter baskets

D. 1 CUP & 2 CUP dual wall ﬁlter baskets

E. Cleaning disc

F. The Razor™ precision dose trimming tool

G. Water hardness test strip

H. Espresso cleaning tablets

I. Cleaning tool for steam wand tip

J. Allen key

10 11

PAGE HEADER..... PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

BEFORE FIRST USE

Machine Preparation

Remove and discard all labels and

packaging materials attached to your

espresso machine. Ensure you have

removed all parts and accessories before

discarding the packaging.

Remove the water tank located at the

back of the machine by pulling down the

water tank handle. Remove the plastic bag

containing the water ﬁlter and water ﬁlter

holder. Clean parts and accessories (water

tank, portaﬁlter, ﬁlter baskets, jug) using

warm water and a gentle dish washing

liquid. Rinse well then dry thoroughly.

TIP

To easily maneuver your machine, use the

drop down swivel foot located under the

drip tray. When turned to UNLOCK, the

swivel foot drops down & lifts the machine

upwards, making it easier to access the

removable water tank or reposition the

machine to another location.

INSTALLING THE WATER FILTER

• Remove the water ﬁlter and water ﬁlter

holder from the plastic bag.

• Soak the ﬁlter in a cup of water for

5 minutes then rinse under cold

running water.

• Wash the ﬁlter holder with cold water,

taking speciﬁc care to rinse the

stainless steel mesh.

Soak filter for 5 minutes Rinse filter & mesh

• Insert the ﬁlter into the two parts of the

ﬁlter holder.

Place filter into

filter holder

• To install the assembled filter holder

into the water tank, align the base of the

ﬁlter holder with the adapter inside the

water tank. Push down to lock into place.

• Fill the water tank with cold water before

sliding back into position at the back of

the machine and locking into place.

NOTE

DO NOT use highly ﬁltered,

demineralized or distilled water in this

machine. This may affect the taste of the

coffee and how the machine operates.

NOTE

To purchase water ﬁlters, visit

www.breville.com or call Breville

Consumer Support.

OPERATING YOUR BREVILLE PRODUCT

FIRST USE

1. Ensure tank is ﬁlled with cold water.

You can do this by either opening

the top-ﬁll water tank lid (push to

open), or by removing the water tank

at the back of the machine.

2. Check STEAM LEVER and HOT

WATER dial are in the CLOSED

position.

3. Press POWER button to turn

machine on.

4. The LCD will display ‘Hrd3’,

prompting you to set the water

hardness level. Programming this

will determine the regularity of the

‘NEW FILTER’ alert which indicates

when the water ﬁlter in the water

tank needs to be replaced.

Setting Water Hardness

• Remove the supplied water hardness test

strip from the wrapper.

• Dip the test strip into a sample of the

water you have ﬁlled the tank with. Wait

for one minute. The water hardness

setting is indicated by the number of

red squares displayed on the test strip

eg. 3 red squares indicates a water

hardness setting of 3.

• Press UP or DOWN arrow to the

required setting from ‘Hrd1’ (softest

water) to ‘Hrd5’ (hardest water). Press

MENU button to set. Machine will beep

to conﬁrm selection.

NOTE

If there is no selection within 5 minutes,

the machine will default to setting

‘Hrd3’.

5. A pumping/vibrating sound will be

heard indicating empty boilers are

being ﬁlled with water for the ﬁrst

time. The LCD will display the current

boiler temperature as it heats up.

6. After approximately 10 minutes,

the machine will reach the

default operating temperature

(200˚F/93˚C) and all 4 buttons will

illuminate. The machine is now in

STANDBY mode, ready for the next

step, ‘Flushing The Machine’.

POWER

NOTE

You will not be able to select the 1 CUP

or 2 CUP functions; access the cleaning

cycle in the menu options; or activate the

steam wand until the machine has reached

operating temperature (STANDBY mode).

The machine will beep 3 times if one of

these functions is selected.

12 13

PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

Flushing The Machine

When the machine has reached

STANDBY mode:

1. Press 2 CUP button to run

water through the group head for

30 seconds.

2. Rotate HOT WATER dial to

the OPEN position to run water

through the hot water outlet. After

30 seconds, rotate HOT WATER dial

to the CLOSED position.

3. Lift STEAM LEVER to the OPEN

position to release steam through

the steam wand. After 30 seconds,

lower the STEAM LEVER to the

CLOSED position.

4. Repeat steps 1–3 twice.

5. Re-ﬁll water tank and empty drip

tray, if required.

POWER SAVE MODE

The machine will enter POWER SAVE mode

after remaining idle for 1 hour and turn off

completely if not used for a continuous

4 hour period.

Pressing any button during POWER

SAVE (except POWER), or operating the

STEAM LEVER or HOT WATER dial will

cause the machine to heat-up to operating

temperature.

Pressing the POWER button during

POWER SAVE will turn the machine off.

LCD INTERFACE

Display modes

3 modes can be displayed on the LCD screen:

Shot Temperature, Shot Clock or Clock.

Press UP or DOWN arrow to change the

display mode.

1. Shot Temp

Displays selected extraction temperature.

The default is 200°F (93°C), but can be

changed from 190°F–205°F (86°C–96°C).

See ‘Extraction Temperature’, page 17.

2. Shot Clock

Displays duration of espresso extraction in

seconds. See ‘Extraction Guide’, page 26.

Shot clock will be displayed during an

extraction and 10 seconds after the

extraction before returning to the default

shot temperature display mode.

OPERATING YOUR BREVILLE PRODUCT

3. Clock

Displays current time. The default is

12:00AM if the time has not been set.

See ‘Set Clock’, page 17.

If selected, the clock will display for

10 seconds before returning to the default

shot temperature display mode.

GENERAL OPERATION

The 1 CUP & 2 CUP buttons use duration to

control espresso volume. The duration times

are preset, but can be reprogrammed (refer

to ‘Reprogramming Shot Duration’, page 16).

Alternatively, access the Advanced Features

if you wish to use volumetric controls

instead of duration to determine espresso

volume (refer to ‘Volumetric Control (vOL)’,

page 19).

1 CUP BUTTON

Press 1 CUP button once to extract a single

shot of espresso at the preset duration

(30 seconds). The extraction will start

using the low pressure pre-infusion.

The machine will stop after 30 seconds and

return to STANDBY mode.

TIP

To by-pass low pressure pre-infusion

and deliver water to the group head at

full pump pressure, press and hold the

1 CUP button. Release button when

the desired amount of espresso has

been extracted. This function can be

used when purging the group head.

2 CUP BUTTON

Press 2 CUP button once to extract a

double shot of espresso at the preset

duration (30 seconds). The extraction will

start using the low pressure pre-infusion.

The machine will stop after 30 seconds and

return to STANDBY mode.

TIP

To by-pass low pressure pre-infusion

and deliver water to the group head at

full pump pressure, press and hold the

2 CUP button. Release button when

the desired amount of espresso has

been extracted. This function can be

used when purging the group head.

14 15

PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

MANUAL BUTTON

The MANUAL button allows you to control

the espresso duration/volume to suit your

preference. Press MANUAL button once to

start the espresso extraction.

The extraction will start using the low

pressure pre-infusion. Press MANUAL

button again to stop extraction.

TIP

To manually control the low pressure

pre-infusion duration, press and

hold the MANUAL button. When the

required pre-infusion duration is met,

release button to begin full pump

pressure. Press MANUAL button

again to stop extraction.

STEAM

For instant steam, move STEAM LEVER

to OPEN position. The STEAM LED will

illuminate.

To turn steam off, move STEAM LEVER to

CLOSED position. The machine will return

to STANDBY mode.

CAUTION: BURN HAZARD

Pressurized steam can still be released,

even after machine has been switched off.

Children must always be supervised.

OPERATING YOUR BREVILLE PRODUCT

HOT WATER

For instant hot water, rotate the HOT

WATER dial to OPEN position. The HOT

WATER LED will illuminate.

To turn hot water off, rotate the

HOT WATER dial to CLOSED position.

The machine will return to STANDBY mode.

NOTE

You cannot run hot water and extract

espresso at the same time.

NOTE

Hot water will cease to dispense after

approx. 30 seconds. Depending on

the size of your cup, you may need to

close, then re-open the HOT WATER

dial. See ‘HOT WATER LED ﬂashing’,

page 23.

PROGRAMMABLE FUNCTIONS

To enter program mode, press the MENU

button. Continue to press MENU button

until the desired function is ﬂashing on

the LCD.

Program mode allows you to program:

• Shot Volume

• Shot Temperature

• Auto Start

• Clean Cycle

• Set Clock

To exit program mode, press EXIT button.

NOTE

The MENU button is disabled during

an extraction or when dispensing

hot water.

16 17

PAGE HEADER..... PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

REPROGRAMMING SHOT

DURATION

The 1 CUP and 2 CUP buttons use duration

to control espresso volume. Reprogram

the preset 30 second duration to your

preference.

Press MENU button until ‘SHOT VOL’

ﬂashes and either ‘1 CUP’ or ‘2 CUP’ is

displayed, depending on the button you’d

like to reprogram.

Without the portaﬁlter in place, press the

button you’d like to reprogram (either 1 CUP

or 2 CUP button) to start water ﬂow from

the group head. Using the shot clock on the

LCD, press the 1 CUP or 2 CUP button once

the required duration has been reached.

Reprogramming 1 CUP button

Reprogramming 2 CUP button

The machine will beep. Press the EXIT

button to set the new duration.

REPROGRAMMING SHOT

VOLUME

The 1 CUP and 2 CUP buttons use duration

to control espresso volume. Access the

Advanced Features if you wish to use

volumetric controls instead of duration

to determine espresso volume (refer to

‘Volumetric Control (vOL)’, page 19). Then

follow these instructions:

Press MENU button until ‘SHOT VOL’

ﬂashes and either ‘1 CUP’ or ‘2 CUP’ is

displayed, depending on the button you’d

like to reprogram.

Dose & tamp the portaﬁlter with ground

coffee. Insert the portaﬁlter into the

group head. Press the button you’d like to

reprogram (either 1 CUP or 2 CUP button)

to start espresso extraction. Press the 1 CUP

or 2 CUP button once the desired volume of

espresso has been extracted. The machine

will beep. Press the EXIT button to set the

new volume.

OPERATING YOUR BREVILLE PRODUCT

EXTRACTION TEMPERATURE

Press MENU button until ‘SHOT TEMP’

ﬂashes. The LCD will display the current

shot temperature.

Press UP or DOWN arrow to adjust

the temperature. The default is set at

200°F (93°C) but can be changed from

190°F – 205°F (86°C – 96°C).

The optimum temperature will depend

on the origin of the coffee beans, their

freshness and degree of roast.

We recommend a temperature range

between 194°F – 203°F (90°C – 95°C)

for optimal ﬂavor.

The new temperature will be displayed

on the LCD. Press the EXIT button to set.

SET CLOCK

Setting the clock is optional. Press MENU

button until ‘SET CLOCK’ ﬂashes. The

default is 12.00AM if time has not been set.

Press UP or DOWN arrow to adjust the time.

For faster scrolling, press and hold the UP or

DOWN arrow. Press the EXIT button to set.

18 19

PAGE HEADER..... PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

AUTO START

Auto Start is optional. It allows you to

program the speciﬁc time when the machine

will automatically turn on. By programming

your machine, you will not have to wait for

it to pre-heat. We recommend programming

the machine to start 15 minutes before you

plan to use it.

Press MENU button until ‘AUTO START’

ﬂashes and the current Auto Start setting

(ON or OFF) is displayed on the LCD.

Press UP or DOWN arrow to set the

AUTO START to ON or OFF.

If OFF is selected, press the EXIT button

to set.

If ON is selected, press the MENU button.

Press UP or DOWN arrow to the desired

Auto Start time. For faster scrolling, press

and hold the UP or DOWN arrow.

Press the EXIT button to set. A small clock

icon will be displayed on the LCD when the

Auto Start function has been programmed.

CLEANING CYCLE

The cleaning cycle cleans the shower screen

and back-ﬂushes the group head.

Select this feature when the LCD displays

‘CLEAN ME!’ Refer to ‘Cleaning Cycle’,

page 29.

OPERATING YOUR BREVILLE PRODUCT

ADVANCED FEATURES

These features should only be accessed by

experienced users.

To access Advanced Features, with the

machine turned off, press and hold the

1 CUP button, then also press the POWER

button. Press the UP arrow to the desired

feature then press MENU button to access

feature settings.

Press the EXIT button at any time to exit.

POWER

TURN

POWER OFF

THEN PRESS

& HOLD

Reset Default Settings (rSET)

Use this function to reset all programmable

values back to the default settings. The

machine has the following default settings:

1. Temperature – 200°F (93°C)

2. Pre-Infusion – Duration Pd07

3. Pre-Infusion – Power PP60

4. Steam temperature – 275°F (135°C)

5. Machine Audio – LO

6. Auto Off – ON

7. Auto Start – OFF

8. Temperature Unit – Fahrenheit

9. Water Hardness – Hrd3

10. Shot Duration – 30 secs

While ‘rSET’ is displayed on the LCD, press

the MENU button to reset all settings to

factory defaults. Machine will beep to

conﬁrm selection.

‘Hrd3’ will ﬂash on screen. Machine is now

in Water Hardness mode. Determine water

hardness with the supplied water hardness

test strip. Refer to ‘Setting Water Hardness’,

page 11. Press UP or DOWN arrow to the

required setting from ‘Hrd1’ (softest water)

to ‘Hrd5’ (hardest water). Press MENU

button to set. Machine will beep to conﬁrm

selection.

Setting water hardness will determine the

regularity of the ‘NEW FILTER’ alert which

indicates when the water ﬁlter in the water

tank needs to be replaced.

Descale (dESC)

Select this feature to access the step by step

descale procedure on the LCD. Refer to

page 28 for the accompanying instructions.

20 21

PAGE HEADER..... PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

Temperature Unit - ˚C/˚F (SEt)

Set units to metric or imperial. While ‘SEt’ is

displayed on the LCD, press MENU button.

Press UP or DOWN arrow to the desired

unit. Press MENU button to set. Machine

will beep to conﬁrm selection.

Steam Temperature (StEA)

Adjust the steam boiler temperature,

which in turn controls steam pressure.

Lower steam temperature to texture smaller

volumes of milk or to have more control.

Increase steam temperature to texture larger

volumes of milk.

While ‘StEA’ is displayed on the LCD, press

MENU button. Press UP or DOWN arrow

to the desired temperature. Press MENU

button to set. Machine will beep to

conﬁrm selection.

Disable AUTO OFF (A OF)

Use this function to disable the Auto Off

feature. While ‘A OF’ is displayed on the

LCD, press MENU button. Press UP or

DOWN arrow to select off or on. Press

MENU button to set. Machine will beep

to conﬁrm selection.

Machine Audio (Snd)

Adjust the audible alerts. While ‘Snd’ is

displayed on the LCD, press MENU button.

Press UP or DOWN arrow to off (OFF), low

(LO) or high (HI). Press MENU button to

set. Depending on the selected setting, the

machine may beep to conﬁrm selection.

OPERATING YOUR BREVILLE PRODUCT

Volumetric Control (vOL)

Select between volume based (FLo) or

time based (SEc) method for espresso dose

measurement. While ‘vOL’ is displayed on

the LCD, press MENU button. Press UP or

DOWN arrow to the desired method. Press

MENU button to set. Machine will beep to

conﬁrm selection.

PRE-INFUSION PROGRAMMING

With the machine on and in STANDBY

mode, press UP and DOWN arrow together

to enter Pre-Infusion Programming mode.

Press MENU button to move between

Pre-Infusion Duration (Pd) and Pre-Infusion

Power (PP).

Pre-Infusion Duration (Pd)

The LCD will display the current

Pre-Infusion Duration.

Press UP or DOWN arrow to vary time.

We recommend a range between 5–15 secs

as being optimum. Press MENU button to

access Pre-Infusion Power, or press EXIT

button to set.

Pre-Infusion Power (PP)

The LCD will display current

Pre-Infusion Power.

Press UP or DOWN arrow to vary power.

We recommend a range between 55-65 as

being optimum. Press EXIT button to set.

ALERTS

STEAM LEVER beeps during heat-up

The machine will beep 3 times and not

reach operating temperature (STANDBY

mode) if the STEAM LEVER is in the OPEN

position. Move the STEAM LEVER to the

CLOSED position.

HOT WATER LED ﬂashing during heat-up

The machine will not reach operating

temperature (STANDBY mode) if the HOT

WATER dial is in the OPEN position. The

HOT WATER LED will ﬂash. Move the HOT

WATER dial to the CLOSED position.

HOT WATER LED ﬂashing

To ensure water is dispensed at the correct

temperature, hot water will cease to

dispense after approx. 30 seconds and the

HOT WATER LED will ﬂash. Move the

HOT WATER dial to the CLOSED position.

22 23

PAGE HEADER..... PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

Fill Tank

The machine will detect a low water level.

The LCD will display ‘FILL TANK’.

Fill tank with cold fresh water. The machine

will not be able to make coffee or hot water

while the tank is empty.

Clean Me!

Indicates when 200 extractions have been

carried out since the last cleaning cycle.

The cleaning cycle cleans the shower

screen and back-ﬂushes the group head. For

information on how to clean the machine,

refer to ‘Cleaning Cycle’, page 27.

New Filter

Indicates when the water ﬁlter in the water

tank needs to be replaced. For information

on changing the ﬁlter, refer to ‘Installing

Water Filters’, page 27.

The regularity of this alert is determined

by the water hardness setting (Hrd1-Hrd5)

selected. For information, refer to ‘Setting

Water Hardness’, page 11.

Temperature ﬂashing

Indicates when the machine is heating up

or if the temperature drops excessively

during use.

TRANSPORTING AND STORING

We recommend draining both boilers

completely before transporting the machine

or storing for an extended period of time.

This procedure is also intended as an

anti-freeze measure in the event the machine

is exposed to extreme cold temperatures.

COFFEE MAKING TIPS & PREPARATION

PRE-HEATING

Heating your cup or glass

A warm cup will help maintain the coffee’s

optimal temperature. Pre-heat your cup by

rinsing with hot water from the hot water

outlet and place on the cup warming tray.

Heating the portaﬁlter and ﬁlter basket

A cold portaﬁlter and ﬁlter basket can

reduce the extraction temperature enough

to signiﬁcantly affect the quality of your

espresso. Always ensure the portaﬁlter and

ﬁlter basket are pre-heated with hot water

from the hot water outlet before initial use.

NOTE

Always wipe the portaﬁlter and ﬁlter

basket dry before dosing with ground

coffee as moisture can encourage

‘channeling’ where water by-passes the

ground coffee during extraction.

SELECTING FILTER BASKET

Single Wall Filter Baskets

Use Single Wall ﬁlter baskets if grinding

fresh whole coffee beans.

Single Wall ﬁlter baskets allow you to

experiment with grind and dose to create a

more balanced espresso.

1 CUP 2 CUP

Dual Wall Filter Baskets

Use Dual Wall ﬁlter baskets if using

pre-ground coffee.

Dual Wall ﬁlter baskets regulate the

pressure and help to optimize the

extraction regardless of the grind, dose or

freshness.

1 CUP 2 CUP

NOTE

Regardless of whether you use Single

Wall or Dual Wall ﬁlter baskets, use

the 1 CUP basket when brewing a

single cup and the 2 CUP basket when

brewing two cups or a stronger single

cup or mug.

THE GRIND

If grinding coffee beans, the grind size

should be ﬁne but not too ﬁne. The grind

size will affect the rate at which the water

ﬂows through the ground coffee in the ﬁlter

basket and the taste of the espresso.

If the grind is too ﬁne (looks like powder

and feels like ﬂour when rubbed between

ﬁngers), the water will not ﬂow through

the coffee even when under pressure.

The resulting espresso will be OVER-

EXTRACTED, dark in color and bitter

in ﬂavor.

If the grind is too coarse the water will

ﬂow through the ground coffee in the ﬁlter

basket too quickly. The resulting espresso

will be UNDER-EXTRACTED and lacking

in color and ﬂavor.

24 25

COFFEE MAKING TIPS & PREPARATION

DOSE AND TAMPING

• Wipe ﬁlter basket with a dry cloth.

• If using Single Wall ﬁlter baskets, grind

just enough coffee to ﬁll the ﬁlter basket.

You may need to experiment with how

long the grinder needs to run to achieve

the correct dose.

• Tap the portaﬁlter several times to

distribute the coffee evenly in the

ﬁlter basket.

• Tamp down ﬁrmly (using approx.

30-40lbs or 15-20kg of pressure). The

amount of pressure is not as important

as consistent pressure every time.

• As a guide to dose, the top edge of the

metal cap on the tamper should be level

with the top of the ﬁlter basket after the

coffee has been tamped.

TRIMMING THE DOSE

The Razor™ precision dose trimming tool

allows you to trim the puck to the right level

for a consistent extraction.

the Razor

™

Precision dose trimming tool

• Insert the Razor™ dose trimming tool

into the ﬁlter basket until the shoulders

of the tool rest on the rim of the basket.

The blade of the dose trimming tool

should penetrate the surface of the

tamped coffee.

• Rotate the Razor™ dose trimming

tool back and forth while holding the

portaﬁlter on an angle over a knock

box to trim off excess coffee grinds.

Your ﬁlter basket is now dosed with the

correct amount of coffee.

• Wipe excess coffee from the rim of the

ﬁlter basket to ensure a proper seal is

achieved in the group head.

TIP

If the extraction is too fast, make the

grind ﬁner & repeat above steps. If the

extraction is too slow, make the grind

coarser and repeat above steps.

PURGING THE GROUP HEAD

Before placing the portaﬁlter into the group

head, run a short ﬂow of water through the

group head by pressing and holding the

1 CUP button. Allow water to ﬂow for

5 seconds, then release the 1 CUP button to

stop the ﬂow of water. This will purge any

ground coffee residue from the group head

and stabilize the temperature prior

to extraction.

COFFEE MAKING TIPS & PREPARATION

INSERTING THE PORTAFILTER

Place the portaﬁlter underneath the group

head so the handle is aligned with the

INSERT position. Insert the portaﬁlter

into the group head and rotate to the right

until the handle is securely locked in place.

Rotating past the center will not damage the

silicone seal.

EXTRACTING ESPRESSO

• Place pre-warmed cup(s) beneath the

portaﬁlter and press the MANUAL,

1 CUP or 2 CUP button.

• As a guide, the espresso will start

to ﬂow after 9–14 seconds (this includes

pre-infusion time) and should be the

consistency of dripping honey.

• If the espresso starts to ﬂow before

9 seconds you have either under

dosed the ﬁlter basket and/or the

grind is too coarse. This is an

UNDER-EXTRACTED shot.

• If the espresso starts to drip or ﬂow

after 14 seconds, then you have

either over dosed the ﬁlter basket

and/or the grind is too ﬁne. This is

an OVER-EXTRACTED shot.

A great espresso is about achieving the

perfect balance between sweetness, acidity

and bitterness.

The ﬂavor of your coffee will depend on

many factors, such as the type of coffee

beans, degree of roast, freshness, coarseness

or ﬁneness of the grind, dose of ground

coffee, and tamping pressure.

Experiment by adjusting these factors

just one at a time to achieve the taste

of your preference.

TEXTURING MILK

• Always start with fresh cold milk.

• Fill the jug just below the “V” at the

bottom of the spout.

• Position the steam tip above the drip tray

and lift the STEAM LEVER to purge the

steam wand of any condensed water.

• Insert the steam tip ¼-¾" (1-2cm)

below the surface of the milk, close to

the right hand side of the jug at the

3 o’clock position.

• Move the STEAM LEVER to the OPEN

position.

• Keep the tip just under the surface of the

milk until the milk is spinning clockwise,

producing a vortex (whirlpool effect).

• With the milk spinning, slowly lower the

jug. This will bring the steam tip to the

surface of the milk & start to introduce

air into the milk. You may have to gently

break the surface of the milk with the tip

to get the milk spinning fast enough.

• Keep the tip at or slightly below the

surface, continuing to maintain the

vortex. Texture the milk until sufﬁcient

volume is obtained.

• Lift the handle of the jug to lower the

tip beneath the surface, but keep the

vortex of milk spinning. The milk is at

the correct temperature (140–150°F or

60–65°C) when the jug is hot to touch.

• Move the STEAM LEVER to the

CLOSED position BEFORE taking the

tip out of the milk.

• Set the jug to one side. Wipe the wand &

tip with a damp cloth. Position the steam

tip above the drip tray and lift the steam

lever to purge out any residual milk.

• Tap the jug on the bench to collapse

any bubbles.

• Swirl the jug to “polish” and re-integrate

the texture.

• Pour milk directly into the espresso.

• The key is to work quickly, before the

milk begins to separate.

26 27

OPTIMUM OPTIMUM 25-35 SECBALANCED

GRIND TAMPGRIND DOSE SHOT TIME

TOO FINE

TOO MUCH

USE RAZOR TO TRIM

TOO LITTLE

INCREASE DOSE &

USE RAZOR TO TRIM

OVER 40 SEC

OVER EXTRACTED

BITTER

•

ASTRINGENT

TOO COARSE UNDER 20 SEC

UNDERDEVELOPED

•

SOUR

UNDER EXTRACTED

30-40lbs

(15-20kg)

TOO HEAVY

TOO LIGHT

EXTRACTION GUIDE

HINTS & TIPS

• Fresh, quality coffee beans will give

you the best possible extraction.

• We recommend quality 100% Arabica

beans with a ‘Roasted On’ date stamped

on the bag, not a ‘Best Before’ or ‘Use

By’ date.

• Coffee beans are best consumed

between 5–20 days after the

‘Roasted On’ date. Ideally only

grind directly before the extraction

to maximize ﬂavor.

• Buy coffee beans in small batches to

reduce the storage time.

• Store coffee beans in a cool, dark and

dry container. Vacuum seal if possible.

COFFEE MAKING TIPS & PREPARATION CARE & CLEANING

CLEANING CYCLE

• CLEAN ME! will be displayed on the

LCD to indicate when a cleaning cycle

is required (approx. 200 shots).

• Insert the 1 CUP ﬁlter basket into

the portaﬁlter, followed by the

supplied cleaning disc, followed by

1 cleaning tablet.

• Lock the portaﬁlter into the group head,

ensuring it is rotated to the right until

the handle is securely locked in place.

• Ensure the water tank is ﬁlled with

cold water and empty the drip tray.

• Press MENU button until

‘CLEAN CYCLE’ ﬂashes and ‘PUSH’

is displayed on the LCD.

• To start the cleaning cycle press the

illuminated MANUAL button.

• ‘CLEAN CYCLE’ will ﬂash and the

machine will start to countdown from

370 seconds.

• When the cleaning cycle has ﬁnished,

remove the portaﬁlter and ensure

the tablet has completely dissolved.

If the tablet has not dissolved, repeat

the steps above, without inserting a

new tablet.

• The cleaning cycle is now complete.

Rinse the portaﬁlter and ﬁlter basket

thoroughly to remove any tablet residue

before using.

INSTALLING WATER FILTERS

• Discard the used water ﬁlter. Soak a new

ﬁlter in a cup of water for 5 minutes,

then rinse under cold running water.

• Wash the water ﬁlter holder with cold

water, taking speciﬁc care to rinse the

stainless steel mesh.

• Insert the new water ﬁlter into the two

parts of the water ﬁlter holder.

• To install the assembled water ﬁlter

holder into the water tank, align the base

of the water ﬁlter holder with the adapter

inside the water tank. Push down to lock

into place.

• Slide the water tank back into position

at the back of the machine and lock

into place.

NOTE

To purchase additional water ﬁlters,

visit www.breville.com or call

Breville Consumer Support.

CLEANING THE STEAM WAND

• Immediately after texturing milk, wipe

the steam wand with a damp cloth and

purge by lifting the STEAM LEVER for a

few seconds.

• If any of the holes in the tip of the

steam wand become blocked, ensure

the STEAM LEVER is in the CLOSED

position and clean using the pin on the

end of the provided cleaning tool.

• If steam wand remains blocked, remove

the tip using the integrated spanner in

the cleaning tool and soak in hot water.

Screw tip back onto the steam wand

using the integrated spanner in the

cleaning tool.

28 29

CARE & CLEANING

CLEANING THE FILTER BASKETS

AND PORTAFILTER

• The ﬁlter baskets and portaﬁlter should

be rinsed under hot water directly after

use to remove all residual coffee oils.

• If the holes in the ﬁlter baskets become

blocked, dissolve a cleaning tablet in

hot water and soak ﬁlter basket and

portaﬁlter in solution for approx. 20

minutes. Rinse thoroughly.

CLEANING THE SHOWER SCREEN

• The group head interior and shower

screen should be wiped with a damp cloth

to remove any ground coffee particles.

• Periodically purge the machine with

hot water to rinse out any residual

coffee. Place an empty ﬁlter basket into

the portaﬁlter. To by-pass low pressure

pre-infusion and deliver water to the

group head at full pump pressure, press

and hold the 2 CUP button. Release

button after 20 seconds.

CLEAR WATER BACKFLUSH

After each coffee making session we

recommend doing a clear water backﬂush

before you turn off the machine. Insert the

cleaning disc into the ﬁlter basket then

insert the portaﬁlter into the group head.

Press the 2 CUP button and allow pressure

to build for 20secs, then press to stop &

release pressure. Repeat this 5 times to

purge any ﬁne coffee grounds and residual

coffee oils from the brew water paths.

CLEANING THE DRIP TRAY

& STORAGE TRAY

• The drip tray should be removed,

emptied and cleaned after each use or

when the drip tray indicator is showing

Empty Me! Remove grill from the drip

tray. Wash both in warm soapy water.

The Empty Me! indicator can also be

removed from the drip tray.

• The storage tray can be removed and

cleaned with a soft, damp cloth (do not use

abrasive cleansers, pads or cloths

which can scratch the surface).

CLEANING THE OUTER HOUSING

& CUP WARMING TRAY

The outer housing and cup warming tray can

be cleaned with a soft, damp cloth. Polish with

a soft, dry cloth. Do not use abrasive cleansers,

pads or cloths which can scratch the surface.

NOTE

Do not clean any of the parts or

accessories in the dishwasher.

DESCALE (dESC)

Use this function to access descale procedures

when a descale alert is displayed on the LCD.

Please ensure you allow approximately 1.5 hour

to complete the entire descale process and

follow the step by step instructions.

If you’ve just ﬁnished using your machine,

please ensure to turn the machine off and

allow to cool for at least 1 hour before

starting your descale process.

1 – Prepare for Descale

a) Empty the drip tray and insert into

position.

b) Turn the machine off and allow to cool

for at least 1 hour. With the machine

off, press and hold the 1 CUP button,

then press and hold the POWER button

together for 3 seconds. rEST will apear

on the LCD.

CARE & CLEANING

c) Press UP or DOWN arrow to set mode, the

‘dESC’ will appear on the LCD. Press the

MENU button to enter Descale mode.

2 – Empty Boilers

a) Remove the grey silicone cover on the

lower front panel marked DESCALE

ACCESS. Place a cloth over the drip tray

to stop steam escaping.

REMOVE

b) Use a ﬂat-head screwdriver to rotate the

right screw counter-clockwise until the

valve is fully open. As the valve opens,

steam may be released.

NOTE

If there’s no water released into the

drip tray, press and hold the 1 CUP

button for 3 seconds. This will release

water from the boiler

When the water is completely empty, close

the valve by rotating screws clock-wise until

sealed. Do not overtighten screws to avoid

damages to the valves.

c) Next, repeat the above process on the

left screw.

d) Empty the drip tray. Use caution as the

drip tray may be hot.

e) Empty water tank, remove water ﬁlter.

f) Place descale solution into water tank,

ﬁll with cold water to MAX line,

(if an alternative cleaning solution is

used, please follow the manufacturer’s

instructions accordingly). Lock water

tank back into position at the back of

the machine.

NOTE

If water tank has not been removed,

replaced or is empty, “FILL TANK”

will appear on the LCD.

30 31

3 – Begin Descale

Press MANUAL button to proceed.

Machine will ﬁll boilers with descale solution

and heat to temperature. During this time,

water may ﬂow through the group head.

Wait for countdown timer to reach 0. This

allows solution to dissolve scale build-up.

However you can proceed to the next step at

any time by pressing the 1 Cup button.

a) Place a cloth over the drip tray to stop

steam escaping.

b) Empty boilers by repeating steps

2b and 2c.

c) Empty drip tray and insert back to place.

d) Empty water tank then rinse and ﬁll with

clean water to the MAX line. Lock water

tank back into position.

4 – Flush Boilers

Press MANUAL button to proceed.

During this procedure, the LCD will show

countdown time (20 minutes).

During this time, the machine will ﬁll boilers

with fresh clean water and heat to temperature.

You can proceed to the next step at any time by

pressing the 1 Cup button.

a) Place a cloth over the drip tray to stop

steam escaping.

b) Empty boilers by repeating steps

2b and 2c.

c) Empty drip tray and insert back to place.

d) Empty water tank then rinse and ﬁll with

clean water to the MAX line. Lock water

tank back into position.

5 - Repeat Step 4 Flush Boilers

We recommend ﬂushing boilers again to

ensure any residual descale solution is

released from the boilers.

Press POWER button to escape the Descale

mode. The descale process is now complete

and ready to use.

CARE & CLEANING TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

The HOT WATER

LED ﬂashes when the

machine is turned on

• HOT WATER dial is

OPEN.

Turn the HOT WATER dial to

the CLOSED position.

Machine beeps

when turned on

• STEAM LEVER is

OPEN or has been

activated before the

machine has reached

operating temperature.

Move the STEAM LEVER to

the CLOSED position.

Water does not ﬂow

from the group head

• Machine has not

reached operating

temperature.

Allow time for the machine to

reach operating temperature.

The POWER button will

stop ﬂashing when machine

is ready.

• Water tank is empty. Fill tank.

• Water tank is not fully

inserted and locked

into position.

Push water tank in fully and

lock latch closed.

FILL TANK on LCD,

but water tank is full

• Water tank is not fully

inserted and locked

into position.

Push water tank in fully and

lock latch closed.

No steam or hot water • Machine is not

turned on.

Ensure the machine is

plugged in and the POWER

button is on.

No hot water • Water tank is empty. Fill water tank.

No steam • Steam wand is blocked. Use the pin on the end of the

provided cleaning tool. If

steam wand remains blocked,

remove the tip using the

integrated spanner in the

cleaning tool and soak in hot

water. Screw tip back onto

the steam wand using the

integrated spanner in the

cleaning tool.

32 33

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

The machine is on but

ceases to operate

Turn machine off. Wait for

60 minutes and turn machine

back on.

If problem persists, call

Breville Consumer Support.

Steam pouring out of

group head

Turn machine off. Wait for

60 minutes and turn machine

back on.

If problem persists, call

Breville Consumer Support.

Espresso only drips

from the portaﬁlter

spouts, restricted ﬂow

• Coffee is ground

too ﬁnely.

Use slightly coarser grind.

• Too much coffee in the

ﬁlter basket.

Lower dose of coffee by

tamping then using the Razor™

dose trimming tool to trim off

excess coffee.

• Coffee tamped too

ﬁrmly.

Tamp between 30–40lbs

or 15–20kg of pressure.

• The ﬁlter basket may be

blocked.

Use the ﬁne pin on the

provided cleaning tool

to clear the outlet hole(s) on

the under side of the ﬁlter

basket. If it continues to be

blocked, dissolve a cleaning

tablet in hot water and soak

ﬁlter basket and portaﬁlter

in the solution for approx.

20 minutes. Rinse thoroughly.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

Espresso runs out too

quickly

and/or

Pressure gauge not

reaching 9 bar

• The coffee is ground

too coarse.

Use slightly ﬁner grind.

• Not enough coffee in

the ﬁlter basket.

Increase dose of coffee. Tamp

then use the Razor™ dose

trimming tool to trim off

excess coffee.

• Coffee not tamped

ﬁrmly enough.

Tamp between 30-40lbs

or 15-20kg of pressure.

If the above suggestions do

not help, check the machine.

Place an EMPTY Dual Wall

ﬁlter basket into the portaﬁlter

(either 1 CUP or 2 CUP). Press

the MANUAL button. If the

pressure gauge reads over

5 bar, the machine is working

correctly. Try re-pulling a

shot, with coffee, using the 3

suggestions above (ﬁner grind,

increase dose, increase tamp).

If the pressure gauge reads

below 5 bar, call Breville

Consumer Support.

• Coffee beans are stale. Use freshly roasted coffee

beans with a ‘Roasted On’ date

and consume between

5–20 days after that date.

Coffee not hot enough • Cups not pre-heated. Rinse cups under hot water

outlet and place on cup

warming tray.

• Milk not hot enough

(if making a cappuccino

or latté etc).

Heat milk until base of

the jug becomes hot

to touch.

• Extraction temperature

is too low.

Increase extraction

temperature. See ‘Extraction

Temperature’, page 17.

34 35

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

No crema • Coffee beans are stale. Use freshly roasted coffee

beans with a ‘Roasted On’ date

and consume between

5–20 days after that date.

• Using Single Wall

ﬁlter baskets with

pre-ground coffee.

Ensure you use Dual Wall ﬁlter

baskets with pre-ground coffee.

Espresso runs out

around the edge of the

portaﬁlter

and/or

Portaﬁlter comes out

of the group head

during an extraction

• Portaﬁlter not inserted in

the group head correctly.

Ensure portaﬁlter is rotated

to the right until the handle

is securely locked in place.

Rotating past the center will

not damage the silicone seal.

• There are coffee

grounds around the

ﬁlter basket rim.

Clean excess coffee from

the rim of the ﬁlter basket to

ensure a proper seal in group

head.

• Filter basket rim is

wet or underside of

portaﬁlter lugs are wet.

Wet surfaces reduce the

friction required to hold

the portaﬁlter in place

whilst under pressure

during an extraction.

Always ensure ﬁlter basket and

portaﬁlter are dried thoroughly

before ﬁlling with coffee,

tamping and inserting into the

group head.

• Too much coffee in the

ﬁlter basket.

After tamping, trim the coffee

dose using the Razor™ dose

trimming tool.

Unable to set Auto

Start time

• Clock not set or clock is

set with incorrect time.

Check that the clock and

Auto Start time have been

programmed correctly.

The LCD will display a clock

icon when the Auto Start time

is programmed.

E1, E2 or E3 error

message on LCD

• An error that cannot

be reset by the user

has occurred.

Call Breville Consumer

Support.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

Coffee puck is sticking

to the shower screen

• This is normal and

happens occasionally.

The dry puck feature

creates a slight

vacuum on top of the

coffee puck which

will occasionally hold

the puck against the

shower screen instead

of leaving it in the ﬁlter

basket.

Pumps continue to

operate / Steam is

very wet & spitty / Hot

water outlet leaks

• Using highly ﬁltered,

de-mineralized or

distilled water which

is affecting how the

machine is designed to

function.

We recommend using cold,

ﬁltered water. We do not

recommend using water

with no/low mineral content

such as de-mineralized or

distilled water. If the problem

persists, contact Breville

Consumer Support.

Too much coffee

extracted

• Coffee is ground too

coarsely.

• Shot duration/

volume needs to be

reprogrammed.

• Adjust the grind size

slightly ﬁner. Tamp then

use the Razor™ dose

trimming tool to trim off

excess coffee.

• Reprogram the shot

duration/volume.

Refer to ‘Reprogramming

Shot Duration & Volume’,

page 18.

36 37

PAGE HEADER.....

PROBLEM POSSIBLE CAUSES WHAT TO DO

Not enough coffee

extracted

• Coffee is ground too

ﬁnely.

• Shot duration/

volume needs to be

reprogrammed.

• Adjust the grind size

slightly coarser. Tamp

then use the Razor™ dose

trimming tool to trim off

excess coffee.

• Reprogram the shot

duration/volume. Refer

to ‘Reprogramming Shot

Duration & Volume’,

page 18.

Amount of coffee

extracted has

changed, but all

settings are the same

• As coffee beans age, the

extraction rate changes

and can affect the shot

volume.

• Adjust the grind size

slightly ﬁner. Tamp then

use the Razor™ dose

trimming tool to trim off

excess coffee.

• Reprogram the shot

duration/volume. Refer

to ‘Reprogramming Shot

Duration & Volume’,

page 18.

• Use freshly roasted coffee

beans with a ‘Roasted On’

date and consume between

5–20 days after that date.

TROUBLESHOOTING COFFEES TO TRY

CAPPUCCINO

A single shot of espresso with textured milk and garnished with

drinking chocolate.

ESPRESSO

Intense and aromatic, it is also known as short black and is

served in a small cup or glass.

LATTÉ

A latté consists of a single espresso with textured milk and

approximately 10mm of foam.

MACCHIATO

Traditionally served short, the macchiato is also poured as an

Americano with a dash of milk or a dollop of textured milk.

AMERICANO

A shot of espresso (single or double) with hot water. Also known

as a long black.

RISTRETTO

A ristretto is an extremely short espresso of approximately

15ml, distinguished by its intense ﬂavor and aftertaste.

38 39

PAGE HEADER..... PAGE HEADER.....

TABLE DES MATIÈRES

39 Breville vous recommande la

sécurité avant tout

42 Faites la connaissance de votre

produit Breville

45 Fonctionnement de votre

produit Breville

61 Trucs & préparation du café

66 Entretien et nettoyage

70 Guide de dépannage

77 Suggestions de café

BREVILLE VOUS RECOMMANDE LA SÉCURITÉ AVANT TOUT

Chez Breville, la sécurité occupe une place de choix. Nous concevons et fabriquons des

produits de consommation sans jamais perdre de vue la sécurité de notre précieuse clientèle.

De plus, nous vous demandons d’être très vigilant lorsque vous utilisez un appareil électrique

et de respecter les mesures de sécurité suivantes:

Lorsque vous utilisez un appareil électrique,

des mesures de sécurité élémentaires

doivent être respectées, incluant ce qui suit:

POUR TOUT APPAREIL

ÉLECTRIQUE

• Lisez attentivement toutes les

instructions avant d’utiliser

l’appareil et conservez-les pour

référence future.

• Ne touchez pas les surfaces

chaudes de l’appareil. Utilisez

les poignées ou les boutons,

tel qu’indiqué dans ce manuel

d’instructions.

• Pour vous protéger contre les

risques de feu, de choc électrique

ou de blessures, n’immergez pas

le cordon d’alimentation, la ﬁche

ou l’appareil lui-même dans l’eau

ou tout autre liquide.

• Surveillez attentivement les

enfants qui utilisent ou sont à

proximité de l’appareil.

• Si l’appareil doit être:

- laissé sans surveillance

- nettoyé

- deplacé

- assemblé ou

- rangé

Éteignez-le toujours en pressant

l’interrupteur, puis débranchez-le

de la prise murale.

• Laissez toujours refroidir

l’appareil avant de le nettoyer, le

déplacer ou le ranger.

• Il est recommandé de vériﬁer

régulièrement l’appareil et le

cordon d’alimentation. N’utilisez

pas l’appareil si le cordon ou

la ﬁche d’alimentation sont

endommagés ou si l’appareil

est défectueux ou endommagé.

Cessez immédiatement l’usage

de l’appareil et appelez le Soutien

aux consommateurs de Breville.

• L’utilisation d’accessoires non

recommandés par Breville peut

causer un risque d’incendie, de

choc électrique ou de blessures.

IMPORTANTES MESURES

DE SÉCURITÉ

La page charge ...

Breville BES920XL Manuel utilisateur

Marque: Breville

Modèle: BES920XL

Catégorie: Cafetières

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Breville BES920XL User manual

Breville BES920XL Manuel utilisateur

Ce manuel convient également à

Breville BES920XL Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents