RIDGID 66658 Mode d'emploi

Model K9-306 FlexShaft

™

Drain Cleaning Machine

K9-306 Manual

• Français – 19

• Castellano – pág. 41

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

ii

Table of Contents

Safety Symbols .................................................................................................................... 2

General Power Tool Safety Warnings

Work Area Safety .............................................................................................................. 2

Electrical Safety ................................................................................................................ 2

Personal Safety ................................................................................................................. 3

Tool Use and Care ............................................................................................................ 3

Service .............................................................................................................................. 4

Specific Safety Information ............................................................................................... 4

FlexShaft Drain Cleaning Machine Safety ........................................................................ 4

RIDGID Contact Information ............................................................................................... 5

Description ........................................................................................................................... 5

Specifications ...................................................................................................................... 6

Standard Equipment ......................................................................................................... 6

Pre-Operation Inspection .................................................................................................... 6

Machine and Work Area Set-up .......................................................................................... 7

Installing/Adjusting Chain Knocker ................................................................................... 9

Operating Instructions .......................................................................................................11

Transportation ................................................................................................................. 15

Storage ............................................................................................................................... 15

Maintenance Instructions ................................................................................................. 15

Cleaning ......................................................................................................................... 15

Lubrication ....................................................................................................................... 16

Cable Re-termination ....................................................................................................... 16

Cable Assembly Replacement ......................................................................................... 16

Motor Brush Inspection/Change .................................................................................... 16

Motor Thermal Overload ................................................................................................. 16

Troubleshooting .............................................................................................................. 17

Service And Repair ......................................................................................................... 18

Optional Equipment .......................................................................................................... 18

Disposal .............................................................................................................................. 18

EC Declaration of Conformity .................................................................. Inside Back Cover

Lifetime Warranty ................................................................................................. Back Cover

*Original Instructions - English

Model K9-306

FlexShaft

™

Drain Cleaning

Machine

WARNING!

Read this Operator’s Man ual

carefully before using this

tool. Failure to understand

and follow the contents of

this manual may result in

electrical shock, fire and/or

serious person al injury.

Drain Cleaning Machine

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

2

This symbol indicates the risk of hands,

fingers or other body parts being caught,

wrapped or crushed in the drain cleaning

FlexShaft.

Safety Symbols

In this operator’s manual and on the product, safety symbols and signal words are used to

communicate important safety information. This section is provided to improve understand-

ing of these signal words and symbols.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey

all safety messages that follow this symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death

or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor

or moderate injury.

NOTICE indicates information that relates to the protection of property.

sive atmospheres, such as in the pres-

ence of flammable liquids, gases or

dust. Power tools create sparks which

may ignite the dust or fumes.

• Keep children and by-standers away

while a power tool. Distractions can

cause you to lose control.

Electrical Safety

• Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified

plugs and matching outlets will reduce

risk of electric shock.

• Avoid body contact with earthed or

grounded surfaces such as pipes, radi-

ators, ranges and refrigerators. There is

an increased risk of electrical shock if your

body is earthed or grounded.

•

Do not expose po

wer tools to rain or

General Power Tool

Safety Warnings*

WARNING

Read all safety warnings, instructions,

illustrations and specifications provided

with this power tool. Failure to follow all

instructions listed below may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS

AND INSTRUCTIONS FOR

FUTURE REFERENCE!

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work Area Safety

• Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

• Do not operate power tools in explo-

NOTICE

DANGER

WARNING

CAUTION

This symbol means read the operator’s

manual carefully before using the equip-

ment. The operator’s manual contains im-

portant information on the safe and proper opera-

tion of the equipment.

This symbol means always wear safety

glasses with side shields or goggles while

using this equipment to reduce the risk of

eye injury.

This symbol indicates the risk of the elec-

trical shock.

This symbol indicates the risk of fingers or

other body parts being caught, wrapped,

crushed or struck by the chain knocker.

Do not operate tool with the cable end outside

of the drain.

This symbol means always wear gloves

when handling or using this equipment to

reduce the risk of infections, burns or other

serious personal injury from the drain contents.

This symbol indicates that the marked

equipment exceeds 55 lbs (25kg). Ex-

ercise caution when lifting or moving to

reduce the risk of injury.

*The text used in the general power tool safety warnings section of this manual is verbatim, as required, from the ap-

plicable UL/CSA/EN 62841-1 standard. This section contains general safety practices for many different types of power

tools. Not every precaution applies to every tool, and some do not apply to this tool.

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

3

facilities, ensure these are connected

and properly used. Use of dust collec-

tion can reduce dust-related hazards.

• Do not let familiarity gained fr

om fre-

quent use of tools allow you to become

complacent and ignore tool safety prin-

ciples. A careless action can cause se-

vere injury within a fraction of a second.

Power Tool Use and Care

• Do not force the power tool. Use the

correct tool for your application. The

correct power tool will do the job better

and safer at the rate for which it is de-

signed.

• Do not use the pow

er tool if the switch

does not turn it ON and OFF. Any power

tool that cannot be controlled with the

switch is dangerous and must be re-

paired.

• Disconnect the plug from the power

source and/or remove the battery pack,

if detachable, from the power tool be-

fore making any adjustments, chang-

ing accessories, or storing power

tools. Such preventive safety measures

reduce the risk of starting the power tool

accidentally.

• Store idle tools out of the reach of chil-

dren and do not allow persons unfamil-

iar with the power tool or these instruc-

tions to operate the power tool. Power

tools can be dangerous in the hands of

untrained users.

• Maintain power tools and accessories.

Check for misalignment or binding of

moving parts, breakage of parts and

any other condition that may affect the

power tool’s op er ation. If damaged,

have the power tool repaired before

use. Many accidents are caused by poorly

maintained power tools.

• Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier to control.

• Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

wet conditions. Water entering a power

tool will increase the risk of electrical

shock.

• Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

• If operating a power tool in a damp

location is unavoidable, use a ground

fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of

electric shock.

Personal Safety

• Stay alert, watch what you are doing

and use common sense when operat-

ing a power tool. Do not use a power

tool while you are tired or under the

influence of drugs, alcohol, or medica-

tion. A mo

ment of inatt

ention while oper-

ating tools may result in serious personal

injury.

• Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protec-

tion used for appropriate conditions will

reduce personal injuries.

• Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or

battery pack, picking up or carrying

the tool. Carrying power tools with your

finger on the switch or energizing power

tools that have the switch on invites acci-

dents.

• Remove any adjusting key or wrench

before turning the power tool ON. A

wrench or a key left attached to a rotating

part of the power tool may result in per-

sonal injury.

• Do

not overreach. Keep proper footing

and balance at all times. This enables

better control of the tool in unexpected

situations.

•

Dress pr

operly. Do not wear loose

clothing or jewelry. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair

can be caught in moving parts.

• If devices are provided for the connec-

tion of dust extraction and collection

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

4

• One person must control both the

cable and the switch. If the cutter stops

rotating, the operator must be able to turn

the tool OFF to prevent the cable from

twisting, kinking and breaking.

• Use late

x or rubber gloves inside the

gloves recommended by the manufac-

turer, goggles, face shields, protective

clothing, and respirator when chem-

icals, bacteria or other toxic or infec-

tious substances are suspected to be

in a drain line. Drains may contain chem-

icals, bacteria and other substances that

may cause burns, be toxic or infectious

or may result in other serious personal

injury.

• Practice good hygiene. Do not eat or

smoke while handling or operating the

tool. After handling or operating drain

cleaning equipment, use hot, soapy

water to wash hands and other body

parts exposed to drain contents. This

will help reduce the risk of health hazards

due to exposure to toxic or infectious

material.

• Only use the Dr

ain Cleaning Machine

for the recommended drain sizes. Us-

ing the wrong size drain cleaner can lead

to twisting, kinking or breaking of the cable

and may result in personal injury.

• Keep glove covered hand on the cable

assembly whenever the FlexShaft Ma-

chine is running. This provides better

control of the cable and helps prevent

twisting, kinking and breaking of the cable

and reduces the risk of injury.

• Position machine cable outlet within

3' (1 m) of the drain inlet or properly

support exposed cable assembly when

the distance exceeds 3' (1 m). Greater

distances can cause control problems lead-

ing to twisting, kinking or breaking of the

cable. Twisting, kinking or breaking cable

may cause striking or crushing injuries.

• Do not wear loose clothing or jewelry.

Keep your hair and clothing away from

moving parts. Loose clothing, jewelry or

hair can be caught in moving parts.

• Do not operate this machine if oper-

ator or machine is standing in water.

Operating machine while in water in-

creases the risk of electrical shock.

• Do not use if there is the risk of con-

tact with other utilities (such as natural

gas or electric) during operation. Visual

• Keep handles and grasping surfaces

dry, clean and free from oil and grease.

Slippery handles and grasping surfaces

do not allow for safe handling and control

of the tool in unexpected situations.

Service

• Have your power tool serviced by a

qualified repair person using only iden-

tical replacement parts. This will ensure

that the safety of the power tool is main-

tained.

Specific Safety

Information

WARNING

This section contains important safety

information that is specific to this tool.

Read these precautions carefully be-

fore using the FlexShaft™ Drain Cleaning

Machine to reduce the risk of electrical

shock or other serious injury.

SAVE ALL WARNINGS

AND INSTRUCTIONS FOR

FUTURE REFERENCE!

Keep this manual with machine for use by

the operator.

FlexShaft Drain Cleaning

Machine Safety

• Before using the tool, test the ground

fault circuit interrupter (GFCI) provided

with the power supply cord to insure it

is operating correctly. A properly oper-

ating GFCI reduces the risk of electrical

shock.

• Only use extension cords that are pro-

tected by a GFCI. The GFCI on the ma-

chine power cord will not prevent electrical

shock from extension cords.

• Only grasp the rotating cable with

gloves recommended by the manu-

facturer. Latex or loose fitting gloves or

rags can become wrapped around the

cable and may result in serious personal

injury.

• Do not allow the cutter to stop turn-

ing while the cable is turning. This can

overstress the cable and may cause twist-

ing, kinking or breaking of the cable and

may result in serious personal injury.

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

5

Figure 1A – RIDGID

®

FlexShaft Drain

Cleaning Machine

Figure 1B –

RIDGID

®

FlexShaft Drain

Cleaning Machine

Figure 1C –

Cable End/Chain Knoc

ker

inspection of the drain with a camera is

a good practice. Crossbores, improperly

placed utilities and damaged drains could

allow the chain knocker to contact and

damage the utility. This could cause elec-

trical shock, gas leaks, fire, explosion or

other serious damage or injury.

• Read and under

stand these instruc-

tions and the instructions and warn-

ings for all equipment and materials

being used before operating this tool

to reduce the risk of serious personal

injury.

RIDGID Contact

Information

If you have any question concerning this

RIDGID

®

product:

– Cont

act your local RIDGID distributor.

– Visit RIDGID.com to find your local

RIDGID contact point.

– Contact Ridge Tool Technical Service De-

par

t

ment

at rtctechservices@emer

son.

com, or in the U

.S. and Canada call (800)

519-3456.

Description

The RIDGID

®

Model K9-306 FlexShaft™

Drain Cleaning Machine is designed to clean

and descale 3" to 6" (75-150 mm) pipes and

drain lines, up to 125' (38 m) in length.

A REV/O-OFF/FOR switch controls cable rota-

tion and a pneumatic foot switch provides ON/

OFF control of the motor. An integral Ground

Fault Circuit Interrupter (GFCI) is built into the

line cord.

The cable assembly is manually fed in and

out of the drain and rotates at 2000 RPM. A

chain knocker that expands to the pipe inside

diameter is used to break up the blockage and

clean the walls of the pipe. Chain knockers

with carbide cutting tips are available for use

on roots and cleaning the scale from the pipe

wall. Plain chain knockers are for general use,

including grease.

FlexShaft Drain Cleaners are well suited to

use with inspection cameras during the drain

cleaning process.

It is not recommended to clean glass, ceramic,

porcelain or similar fixtures with the FlexShaft

Drain Cleaners as it may damage the fixture.

Telescoping Handle

Loading

Wheels

Handle

Latch

Cart Frame

Warning &

Operation

Label

Cable

Chain

Knocker

Cable

Bushing

Wheel

Serial

Number

Plate

Stair

Climber

Foot

(Horizontal-

Use Position)

Loading Handle

Cord

Wrap

Cord/GFCI

Foot

Switch

Chain

Knocker

Clamp

Knocker Bushing

Motor Thermal

Overload Reset

REV/O-OFF/FOR

Switch

Front

Cover

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

6

This machine is made to clean

drains. If properly used it will not damage a

drain that is in good condition and properly

designed, constructed and maintained. If the

drain is in poor condition, or has not been

properly designed, constructed and main-

tained, the drain cleaning process may not be

effective or could cause damage to the drain.

The best way to determine the condition of

a drain before cleaning is through visual in-

spection with a camera. Improper use of this

drain cleaning machine can damage the drain

cleaning machine and the drain. This machine

may not clear all blockages.

Pre-Operation Inspection

WARNING

Before each use, inspect your Drain

Cleaning Machine and correct any prob-

lems to reduce the risk of serious injury

from electric shock, twisted or broken

cables, chemical burns, infections and

other causes and prevent Drain Cleaning

Machine damage.

Always wear safety glasses, and other

appropriate protective equipment when

inspecting your Drain Cleaning Machine.

1. Make sure that the drain cleaning ma-

chine is unplugged and inspect the

power cord, Ground Fault Circuit Inter-

rupter (GFCI) and plug for damage. If

the plug has been modified, or if the cord

is damaged, to avoid electrical shock,

do not use the machine until the cord

has been replaced by a qualified repair

person.

2. Clean the machine, including handles

and contr

ols. This aids inspection and

helps prevent the machine or control

from slipping from your grip. Clean and

maintain the machine per the mainte-

nance instructions.

3. Inspect the machine for

:

• Proper assembly and completeness.

• Any br

oken, worn, missing, misaligned

or binding parts.

• Pr

esence and readability of the warning

label (see Figure 3).

Figure 2 – Machine Serial Number

Serial number plate is located on cart side

of housing. (See Figure 1A) The last 4 digits

indicate the month (MM) and year (YY) of

manufacture.

Specifications

Drain Capacity

(Nom.) ...................3" to 6" (75 – 150 mm)

Cable Diameter

(without Sheath)

.....3/8" (9.5 mm)

Cab

le Assy. Diameter

(with Sheath) ......... 5/8" (15.9 mm)

Cable Assembly

Length

................... 125' (38.1 m)

Mot

or

Power

....... 1.1 kW (1

.5 HP)

1.1 kW (1

.5 HP)

Voltage

..... 1

10-120V

220-240V

Current ..... 1

1A

8A

Refer to on product serial plate for information specific to unit.

Rotational Speed ...2000 RPM

Weight

....................1

59 lbs. (72 kg)

Dimension .............. 36.1" × 32.5" × 20.5"

(918 mm × 826 mm ×

521 mm) Handle down

Operating

Temperature ........... 20°F to 140°F

(-6°C to 60°C)

Sound Pressure

(L

PA

)* ......................96.1 dB(A), K=3

Sound Power

(L

PW

)* .....................91.8 dB(A), K=3

* Sound measurements are measured in accordance

with a standardized test per Standard EN 62481-1.

. - Sound emissions may v

ary due to your location and

specific use of these tools.

. - Daily exposure levels for sound need to be evaluated

for each application and appropriate safety measures

taken when needed. Evaluation of exposure levels

should consider the time a tool is switched off and not

in use. This may significantly reduce the exposure level

over the total working period.

Standard Equipment

Refer to the RIDGID catalog for details on e-

quipment supplied with specific drain cleaning

machine catalog numbers.

XXXXXXXXMMYY

NOTICE

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

7

Machine and Work Area

Set-up

WARNING

Set up the Drain Cleaning Machine and

work area according to these proce-

dures to reduce the risk of injury from

electric shock, fire, machine tipping,

twisted or broken cables, chemical

burns, infections and other causes, and

prevent machine damage.

Always wear safety glasses and other

appropriate protective equipment when

setting up your Drain Cleaning Machine.

1. Check for an appropriate work area.

Operate in a clear level, stable, dry lo-

cation. Do not use the Drain Cleaning

Machine while standing in water.

2. Inspect the drain to be cleaned. If possi-

ble, determine the access point(s) to the

drain, the size(s), length(s), and materi-

al(s) of the drain, distance to mainlines,

the nature of the blockage, presence of

drain cleaning chemicals or other chem-

icals, etc.

If chemicals are pr

esent in the drain, it

is important to understand the specific

safety measures required to work around

those chemicals. Contact the chemical

manufacturer for required information.

Confirm no other utilities are present in

the drain or area to reduce the risk of

damage. Visual inspection of the drain

with a camera is a good practice.

If needed, remove fixture (water closet,

etc.) to allow access to drain. Do not run

the chain knocker in a fixture. This could

damage the FlexShaft Machine or the

fixture.

3. Deter

mine the correct equipment for the

application. See Specifications. Drain

Cleaning Machines for other applications

can be found by consulting the Ridge

Tool Catalog, online at RIDGID.com.

4. Make sure all equipment has been prop-

erly inspected.

5. If needed, place protective covers in the

work area. The drain cleaning process

can be messy.

Figure 3 – Warning Label

• Smooth and free movement of the ca-

ble assembly in and out of the machine.

• Any condition which may prevent safe

and normal operation.

If any problems are found, do not use the

drain cleaning machine until the prob-

lems have been repaired.

4. Clean any debr

is from the cable assem-

bly and chain knockers. Inspect sheath

for wear and damage. There should not

be any cuts, kinks, breaks or excessive

wear. Inspect the cable near the chain

knocker. Cable assemblies should not be

bent or deformed. Cable strands should

be tight to one another without separa-

tion. Inspect chain knocker for damaged

or lost carbide cutting tips (if equipped)

and wear of the chain itself. If chain links

are worn more than ¼ through or dam-

aged, replace the chain knocker. Replace

worn and damaged equipment before

using drain cleaning machine.

Confirm that the chain knocker is prop-

erly set up and is secure on the cable.

5. Inspect and maintain any other equip-

ment being used per its instructions to

make sure it is functioning properly.

6. Make sur

e that the REV/O-OFF/FOR

switch is set to the O-OFF position.

7. With dr

y hands, plug cord into properly

grounded outlet. Test the GFCI provided

in the electrical cord to ensure that it is

operating correctly. Depress the GFCI

TEST button -the machine should not

operate. Depress the RESET button –

the machine should operate. If GFCI is

not functioning properly, unplug the cord

and do not use the drain cleaning ma-

chine until the GFCI has been repaired.

8. With the inspection complet

e, with dry

hands, unplug the machine.

RIDGID.com

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

8

Figure 5– Example of Extending Drain Access

to within 3' of Machine Cable Outlet

9. Unclamp the chain knocker and pull ap-

proximately 4' (1.2 m) of cable assembly

out of the machine.

10

.

Mark the sheath t

o indicate when the

chain knocker is approaching the drain

opening when withdrawn. This can be

done with tape. This reduces the risk of

the chain knockers coming out of the

drain and whipping around. The distance

depends on the configuration of the drain,

but should be at least 4' (1.2 m) from the

chain knocker.

11. Ensure chain knocker is properly in-

stalled (see Installing/Adjusting Chain

Knocker).

12

.

Insert chain knoc

ker end at least 1' (0.3 m)

into drain.

13

.

Evaluat

e the work area and determine if

any barriers are needed to keep bystand-

ers away from the drain cleaning ma-

chine and work area. The drain cleaning

process can be messy, and bystanders

can distract the operator.

14. Position

the foot switch for easy acces-

sibility. You must be able to hold and

control the cable, control the foot switch,

and reach the REV/O-OFF/FOR switch.

15

.

Conf

irm that the REV/O-OFF/FOR switch

is in the O-OFF position.

16

.

Run the cor

d along a clear path. With

dry hands, plug the drain cleaner into a

properly grounded outlet. Some GFCIs

may need to be reset every time they are

plugged in. Reset GFCI if needed. Keep

all connections dry and off the ground. If

6. Transport the drain cleaning machine to

the work area along a clear path. Adjust

handle if necessary (Figure 4). Move han-

dle latches together and move telescop-

ing handle to desired position. Confirm

that the handle latches engage and the

handle is securely held in position. If han-

dle is moved past latch holes, the handle

buttons will prevent the handle from pull-

ing out. If this occurs, depress buttons to

move handle.

Figure 4 – Adjusting Telscoping Handle

7. Place the Drain Cleaning Machine as

shown in Figure 5. Machine should sit

squarely and firmly on the ground.

8. Position the Dr

ain Cleaning Machine so

that the cable outlet is within 3' (1 m) of

the drain access. Greater distances from

the drain access increases the risk of

the cable assembly twisting or kinking. If

the FlexShaft Machine cannot be placed

with the cable outlet within 3' (1 m) of the

drain access, extend the drain access

with similar sized pipe and fittings (see

Figure 5). Improper cable assembly sup-

port can allow the cable to kink and twist

and can damage the cable or injure the

operator. Extending the drain back to the

Drain Cleaning Machine also makes it

easier to feed cable assembly into drain.

Handle Latches

Telescoping Handle

Handle Button

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

9

the power cord is not long enough, use

an extension cord that:

• Is in good condition.

• Has a plug similar to that supplied on

the drain cleaner.

• Is rat

ed for outdoor use and contains

a W or W-A in the cord designation

(i.e. SOW), or complies with H05VV-F,

H05RN-F types or IEC type design

(60227 IEC 53, 60245 IEC 57).

• Has sufficient wire size. For extension

cords up to 50' (15,2 m) long use 16

AWG (1,5 mm

2

) or heavier. For exten-

sion cords 50'-100' (15,2 m – 30,5 m)

long use 14 AWG (2,5 mm

2

) or heavier.

When

using an extension cord, the GFCI

on the drain cleaner does not protect the

extension cord. If the outlet is not GFCI

protected, it is advisable to use a plug

in type GFCI between the outlet and

the extension cord to reduce the risk of

shock if there is a fault in the extension

cord.

17

.

Mov

e the REV/O-OFF/FOR Switch to

the OFF position, and with dry hands

unplug the machine.

Installing/Adjusting Chain

Knocker

1. Select proper chain knocker for the con-

ditions.

Chain knockers are sized based on col-

lar inside diameter and are designed for

specific cable sizes. 3/8" chain knockers

are used on 3/8" cable, etc. Do not use

a larger size chain knocker on a smaller

cable (for instance 1/2" on 3/8"). See Fi-

gure 6 and Collar Distance Chart.

Chain knock

ers without carbide cutting

tips can be used in common pipe types.

These chain knockers work well in grease

and similar blockages.

Chain knock

ers with carbide cutting tips

are used for removing scale from the

inside of the pipe and can be used for

roots. Carbide cutting tips are used for

aggressive cleaning and could damage

pipe, especially softer materials (such

as plastics and Orangeburg), thin walled

pipe, or if the chain knocker is kept in one

position for an extended time.

Do not use chain knockers for cleaning in

glass, ceramic, porcelain or similar ma-

terial fixtures or pipes. They could be

damaged.

2. Figure 7 shows a schematic of proper

chain knocker installation and adjustment.

There are two key points when installing/

adjusting chain knockers.

Collar Distance: Set the chain knocker

collars the correct distance apart (“Collar

Distance”) to allow the chains to spread

an appropriate amount when rotated to

clean the pipe walls. Collar Distance var-

ies based on cable size and pipe diam-

eter, and is generally set using a spacer

made from sheath (“Collar Spacer”). If

additional flexibility is required to navigate

a bend, the collar spacer can be removed

and the collar distance can be set with a

tape measure. Operating without a collar

spacer makes it more likely for the cable

to flip over in use and be damaged. Do

not operate carbide cutters without a

collar spacer to reduce risk of cable

damage.

Exposed Cab

le: Minimize the amount

of exposed cable (cable not covered by

sheath). The more exposed cable there

is, the more likely the cable will flip over

in use and be damaged. Exposed cable

should be limited to no more than ¼" (6

mm), and is set with a bushing made from

sheath (“Knocker Bushing”).

Sheath is

supplied with the drain cleaner

and is available as a service part to allow

configuration as needed for your specific

application. Only use RIDGID FlexShaft

Drain Cleaner sheath of the correct size

for the cable. Any time sheath is cut, it

should be cut cleanly and squarely. Do

not damage the cable when cutting the

sheath.

3. Chain knockers are retained to the cable

with set screws that use a supplied 3 mm

hex key. Loosen set screws and remove

chain knocker, spacer and bushing from

cable.

4. Inspect the sheath end for damage or

wear. The sheath end should be square

and clean. If needed, the sheath end can

be trimmed slightly.

5. If needed,

cut a section of sheath to use

as the collar spacer to the appropriate

size (See Collar Distance Chart).

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

10

Figure 6 – Chain Knocker Selection Chart

K9-306 MACHINE

CATALOG NO.

66618 66623 66628

66633

66638 66643 66648 66653 66658

DESCRIPTION

K9-306

3"

K9-306

4"

K9-306

6"

K9-306

3" CARBIDE

K9-306

4" CARBIDE

K9-306

6" CARBIDE

K9-306 - 3"

PENETRATING

HEAD

K9-306 - 4"

PENETRA

TING

HEAD

K9-306 - 6"

PENETRATING

HEAD

PIPE SIZE

3"

(75 mm)

4"

(105 mm)

5"- 6"

(125-150

mm)

3"

(75 mm)

4"

(105 mm)

5"- 6"

(125-150

mm)

3"

(70 mm)

4"

(100 mm)

5"- 6"

(125-150

mm)

COPPER

GALVANIZED

CAST IRON

PVC

ABS

ORANGEBURG

CORRUGATED

CLAY

GREASE

SOFT

BLOCKAGE

SCALING

ROOTS

WIPES

INCLUDED

WITH KIT

BLOCKAGE

PIPE TYPE

Chain Knockers

Penetrating Head

Chain Knockers

Carbide Tipped Chain Knockers

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

11

Collar distance can be modified to your

preference for the specific pipe/applica-

tion. As collar distance increases, the di-

ameter of the chains decreases, and vice

versa. Improperly set collar distance can

reduce the efficiency of pipe cleaning.

6. Test fit the chain knocker, knocker bushing

and collar spacer on the cable as shown

in Figure 7. Chains should be straight – do

not assemble with chains twisted. To pre-

vent excessive cable end wear, cable end

should be flush with the end of the collar.

Check length of exposed cable. To reduce

the risk of cable flip over and damage,

exposed cable cannot exceed ¼" (6 mm).

If needed, cut a knocker bushing from

sheath to limit exposed cable. Always

use a knocker bushing to reduce wear

on the sheath end.

7. With the chain knoc

ker correctly installed

on the cable as shown in Figure 7, use

the supplied hex wrench to securely

tighten the collar set screws. If the set

screws are not secure, the chain knocker

could slip and damage the cable or be

lost down the drain.

Operation Instructions

WARNING

Always use safety glasses and gloves in good

condition while handling or using. Use latex or

rubber gloves, face shields, protective clothing,

respirators or other appropriate protective equip-

ment when chemicals, bacteria or other toxic or

infectious substances are suspected to be present

to reduce the risk of infections, burns or other

serious personal injury.

Do not allow the chain knocker/end of cable to

stop turning while cable assembly is turning.

This can overstress the cable and may cause

twisting, kinking or breaking of the cable assembly

and may result in serious personal injury.

Keep hand on the cable assembly whenever

the FlexShaft Machine is running. This provides

better control of the cable and helps prevent twist-

ing, kinking and breaking of the cable and reduces

the risk of injury.

Position the FlexShaft Machine cable outlet

within 3' (1 m) of the drain inlet or properly

support exposed cable assembly when the

distance exceeds 3' (1 m). Greater distances can

cause control problems leading to twisting, kinking

Collar Distance Chart

Knocker

Figure 7 – Chain Knocker Installation/Adjustment

Sheath End

Collar Spacer

Cable

Set Scew

(3 mm HEX)

Sheath

Collar Distance

Knocker Collar

Knocker Chain

Cable End

Flush To

Collar

Carbide Cutting Tip

(If Equipped)

Knocker Bushing Knocker Collar

Set Scew

(3 mm HEX)

Exposed Cable

.25" (6.35 mm)

Maximum

Machine

Cable Number Number of Nominal Recommended Collar

Size of Chains Links/Chain Pipe Size Distance

K9-306

3

/8"

3 11 3" (75 mm) 4" (102 mm)

3 13 4" (100 mm) 4

1

/2" (114 mm)

3 17 6" (150 mm) 5" (127 mm)

CATALOG NO.

66618 66623 66628

66633

66638 66643 66648 66653 66658

DESCRIPTION

K9-306

3"

K9-306

4"

K9-306

6"

K9-306

3" CARBIDE

K9-306

4" CARBIDE

K9-306

6" CARBIDE

K9-306 - 3"

PENETRATING

HEAD

K9-306 - 4"

PENETRA

TING

HEAD

K9-306 - 6"

PENETRATING

HEAD

PIPE SIZE

3"

(75 mm)

4"

(105 mm)

5"- 6"

(125-150

mm)

3"

(75 mm)

4"

(105 mm)

5"- 6"

(125-150

mm)

3"

(70 mm)

4"

(100 mm)

5"- 6"

(125-150

mm)

COPPER

GALVANIZED

CAST IRON

PVC

ABS

ORANGEBURG

CORRUGATED

CLAY

GREASE

SOFT

BLOCKAGE

SCALING

ROOTS

WIPES

INCLUDED

WITH KIT

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

12

or breaking of the cable. Twisting, kinking or break-

ing cable may cause striking or crushing injuries.

One person must control both the cable as-

sembly and switch. If the cable stops rotating,

the operator must be able to turn the tool OFF to

prevent twisting, kinking and breaking of the cable

and reduce the risk of injury.

Follow operating instructions to reduce the

risk of injury from twisted or broken cable,

cable ends whipping around, machine tipping,

chemical burns, infections and other causes.

1. Make sure that machine and work area is

properly set-up and that the work area is

free of bystanders and other distractions.

2. Pull cab

le assembly from the machine

and feed into drain. At least 1' (0.3 m) of

cable must be in drain so that the chain

knocker will not come out of the drain and

whip around when the machine is started.

Directly route the cable assembly from

the machine cable outlet to the drain

opening, minimizing exposed cable and

changes in direction. Do not tightly bend

the cable assembly – this can increase

the risk of twisting or breaking.

If using a camera to view the drain clean-

ing process, the camera can be fed in

at the same time. Typically the cable as-

sembly and the camera push rod can be

gripped and advanced/retrieved at the

same time. Keep the camera at least 1.5’

( 0.5 m) behind the chain knocker.

Do not allow the spinning chain

knocker to hit the camera head/push rod.

It can damage it.

3. Assume a proper operating position to

help maintain control of the cable assem-

bly and machine (see Figure 8):

• Be sure y

ou can quickly release the

foot switch.

• Your glo

ved hands must be on the

cable assembly to control and support

as the cable assembly is fed into the

drain and blockage.

• Be sure that y

ou have good balance, do

not have to overreach, and cannot fall

on machine, drain, etc.

• You must be able to reach the REV/O-

OFF/FOR switch.

This operating position will help to main-

tain control of the cable assembly and

FlexShaft Machine.

Figure 8 – In Operating Position

4. Confirm that at least 1' (0.3 m) of cable

assembly is in the drain.

5. Grasp the exposed cable assembly with

both gloved hands equally spaced and pull

6"-12" (150mm - 300mm) of cable out of

the drum so that there is a slight bow in the

cable. Gloved hands must be on the cable

to control and support the cable. Improper

cable support can allow the cable to kink

or twist and can damage the cable or in-

jure the operator. Make sure that the cable

outlet of the drain cleaner is within 3' (1m)

of the drain opening (Figure 8.).

6. Mov

e the REV/O-OFF/FOR switch to FOR

(Forward) position.

7. Depress the f

oot switch to start the ma-

chine. The person controlling the cable

must also control the foot switch. Do not

operate the drain cleaner with one person

controlling the cable and another person

controlling the foot switch. This can lead to

twisting, kinking and breaking of the cable.

8. The FlexShaft Drain Cleaning Machine uti-

lizes high rotational speed and low torque

to clean drains. FlexShaft cable assem-

blies are more flexible than other types

of drain cleaning cables. The FlexShaft

machine is best used by applying light

pressure and slowly working the chain

knocker into the blockage. It’s important

to let the speed of the chain knocker

clean the drain – do not force chain

knockers into blockages.

3' (1 m) MAX.

NOTICE

3' (1 m) MAX.

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

13

9. Advancing/Retrieving the Cable

Assembly – FlexShaft Lubricant

In some cases it may be beneficial to

apply RIDGID FlexShaft lubricant to the

outside of the sheath when feeding the

cable down the drain. This can make it

easier to advance the cable assembly

down the drain and allow greater clean-

ing distance. If doing so, place a clean

towel with lubricant on it in the palm of the

gloved hand used for advancing the cable

assembly, and apply lubricant as feed-

ing the cable assembly (Figure 9). Add

lubricant to the towel as needed during

the process. RIDGID FlexShaft markings

are printed on the sheath every 5' (1.5

m) to aid in determining how much cable

assembly has been fed from the machine.

Only use RIDGID FlexShaft lubricant.

Other lubricants may not be appropriate

for use in a drain and could contaminate

the water.

When retrieving the cable assembly, it is

good practice to use a towel to wipe dirt

and debris from the cable sheath as it is

pulled from the drain and fed back into

the drum.

10

.

Rot

ating the Chain Knocker

Generally the chain knocker is rotated for

cleaning while withdrawing the cable.

Only rotate the cable/chain knocker when

the chain knocker is at least 1' in the

drain. To rotate the cable, firmly grip the

cable and depress the foot switch. The

person controlling the cable assembly

must also control the foot switch. Do not

operate the machine with one person

controlling the cable assembly and an-

other person controlling the foot switch.

Do not allow cable assembly to build up

outside the drain, bow or curve. This can

lead to twisting, kinking and breaking of

the cable. At any time, release the foot

switch to stop cable rotation. When clear-

ing blockages, operate the cable at full

speed for best cleaning. Do not force the

chain knocker into blockages. Rotating

the chain knocker in FORWARD or RE-

VERSE for a short time while advancing

the cable assembly can help it negotiate

the drain and blockages.

Figure 9 – Applying Lubricant to the Cable

Sheath

11. Advance the cable assembly into the

drain, generally not rotating. Grasp the

sheath near where it exits the machine

housing. Pull 6" to 12" (150 to 300 mm)

of cable assembly out of the FlexShaft

Machine so that there is a slight bow in

the cable. Gloved hand must be on cable

assembly to control and support. Improper

cable support can allow the cable as-

sembly to kink or twist and can damage

the cable or injure the operator. Feed the

cable assembly into the drain (Figure 10,

Step 1).

12

.

Contin

ue to advance the cable assem-

bly until the resistance is encountered.

Carefully work the chain knocker through

the blockage. Do not force the cable

assembly – if the chain knocker can-

not turn, it cannot clean the drain. Pay

attention to how far the cable has gone.

Do not overrun the cable into a larger

drain. This can cause the cable to knot up

or cause other damage (Figure 10, Step

2).

13. Once the drain is open, if possible, start

a flow of water down the drain to flush

the debris out of the line and help clean

the cable assembly as it is retrieved. This

can be done by turning on a faucet in the

system or other methods. Pay attention

to the water level, as the drain could plug

again (Figure 10, Step 3).

14. With the chain knocker past the block-

age/area to be cleaned and REV/O-OFF/

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

14

FOR switch in FOR position, depress the

foot switch to rotate the chain knocker.

Slowly pull the cable assembly from the

drain, allowing the rotating chain knocker

to clean the drain walls and break up the

blockage (Figure 10, Steps 4 & 5). If the

cable stops turning, do not continue

operating the machine. This may cause

the cable to twist and kink. At any time, re-

lease the foot switch to stop cable rotation.

Rotating the cable in REVERSE can help

clean the opposite side of the pipe.

Monitor the feedback from the feel of the

cable assembly in your hand and the

sound of the motor/knocker in the drain.

It may be necessary to move the chain

knocker out of the blockage to allow it to

come back up to speed.

If the chain knocker becomes stuck, place

the REV/O-OFF/FOR switch to allow op-

posite rotation. Grasp the cable with both

gloved hands, press the foot switch for

several seconds and pull on the cable until

it is free of the blockage. In some cases, it

may be possible to pull the cable assembly

and the blockage out of the drain by hand.

If this is done, be careful to not damage

the cable assembly.

Place the REV/O-OFF/FOR switch in the

FOR position and continue cleaning the

drain.

Do not allow the spinning chain

knocker to hit the camera head/push rod.

It can damage it.

15. Contin

ue to clean the rest of the drain

while retrieving the cable. Once the drain

has been cleaned, retrieve the cable and

feed back onto the drain cleaning ma-

chine. Pay close attention, as the cable

may lodge in a blockage while being re-

tracted (Figure 10, Step 6).

16. Watch for your sheath marking as the

cable assembly is retrieved. Release

the foot switch when the chain knocker

nears drain opening. Do not pull the chain

knocker from drain while it is rotating. The

chain knocker can whip around and could

cause serious injury.

17

.

If needed for complet

e cleaning, repeat

the above procedure.

18

.

Pull an

y remaining cable assembly from

the line by hand and push back into the

drum. Prepare the machine for transport.

NOTICE

The general operating steps for the FlexShaft Drain Cleaning Machines (see below):

1

3

2

4

5

6

1. Advance the chain knocker (generally not

rotating) to the area of the drain that needs

cleaned.

2.

If there

is a blockage, pass the chain

knocker through the blockage.

3.

If possible

, start a flow of water through the

drain to carry cuttings and debris away as

the drain is cleaned.

4. Rotate the cable/chain knocker at full speed.

5.

Contin

ue to rotate knocker. Gradually with-

draw the cable assembly so that the chain

knocker can break up the blockage.

6. Continue to gradually withdraw the cable

assembly while rotating so that the chain

knocker can clean the walls of the drain.

Figure 10 – General Operating Steps

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

15

Transportation

Feed all of cable assembly into the drum and

secure the chain knocker with the clamp.

Wrap cord and foot switch hose around the

cord wrap. See Figure 11. Before moving the

machine, make sure that the telescoping han-

dle is secured into the extended position for

transport. If the machine needs to be lifted,

use proper lifting techniques. Use care moving

equipment on stairs, and be aware of possible

slip hazards.

Figure 11 – Preparing for Transport

Figure 12 –

One T

ransport Method

Loading

With the telescoping handle locked into the

extended position, place machine with wheels

toward the vehicle. Lean the machine back

and rest the loading wheels on the vehicle

bed. Use loading handles (Figure 12) to lift the

machine and slide it onto the vehicle (Figure

13). Be aware of the machine weight. Use

proper lifting techniques – more than one

person may be required.

Figure 13 – Lifting Unit Onto Vehicle

Storage

The Drain Cleaning Machine

must be kept dry and indoors or well cov-

ered if kept outdoors. Store the machine in

a locked area that is out of reach of children

and people unfamiliar with drain cleaning ma-

chines. This machine can cause serious injury

in the hands of untrained users.

Maintenance

Instructions

WARNING

REV/O-OFF/FOR switch should be O-OFF

and machine unplugged before perform-

ing any maintenance.

Always wear safety glasses and other

appropriate protective equipment when

performing any maintenance.

Cleaning

It is good practice to use a towel to wipe dirt

and debris from the sheath as the cable as-

sembly is pulled from the drain and fed back

into the drum. This will help to keep the drum

clean and reduce the likelihood of the cable

assembly sticking in the drum. If needed,

cable assembly can be pulled from the ma-

chine and the housing opened for flushing/

cleaning.

Clean the machine as needed with hot soapy

water and/or mild disinfectants. Drain the ma-

chine as needed by opening the front cover

(See “Cable Assembly Replacement” step 2).

WARNING

Loading

Handles

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

16

Do not submerge or flush the machine with

water. Do not allow water to enter motor or

other electrical components. Make sure unit is

completely dry before plugging in and using.

Lubrication

The FlexShaft Drain Cleaning Machines are

lubricated for life from the factory.

Cable Re-termination

The Flexshaft cable cannot be shortened or

re-terminated. If the cable is damaged, it must

be replaced. Do not use a damaged cable.

Cable Assembly Replacement

1. Pull entire cable assembly from housing.

2. Use a 4 mm hex wr

ench to loosen the

front cover fasteners (they are retained to

the cover). Lift the cover and unplug the

motor wire connector. Remove the front

cover. (Figure 14).

Figure 14 – Drain Cleaner Housing Opened

3. Remove the cable retention clamp fasten-

ers and retention clamp (Figure 15).

4. Remove the detent pin from the cable

coupling.

5. Remove the cable coupling from the gear

box shaft and remove the cable assembly.

6. Reverse process to assemble. Ensure

cable sheath covers cable – you should

only see cable sheath in the window

in the retention clamp (see Figure 15).

Securely tighten all fasteners.

Figure 15 – Installing Cable Clamp

Motor Brush

Inspection/Change

Brushes should be inspected every 6 months

and changed when shorter than ½" (13 mm).

1. See Cable Assembly Replacement, step

2 to remove cover.

2. Use a screwdriver to remove the brush

cover, Figure 16. Remove brush and

inspect. If there are any signs of dam-

age or shorter than ½" (13 mm), replace

brushes.

3. Re

verse process to reassemble.

4. Place chain knocker in drain and allow to

run 15 minutes in Forward and Reverse,

to break in brushes.

Figure 16 – Inspecting/Changing Motor Brushes

Motor Thermal Overload

The motor is equipped with a thermal over-

load that turns OFF the motor if it gets too

hot. To reset the thermal overload, unplug

machine, turn REV/O-OFF/FOR switch to the

O-OFF position and allow the motor to cool

for 15 minutes. Press the reset button located

on the front cover near the REV/O-OFF/

FOR switch (see Figure 1C). If motor does

not start or the thermal overload continually

trips during normal operation, the machine

Motor Wire

Connector

Front Cover

Cable Sheath

Fills Window

Cable Coupling

Detent Pin

Retention

Clamp

Brush

Covers

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

17

SYMPTOM POSSIBLE REASON SOLUTION

Cable kinking or

breaking.

Cable turns in one

direction but not the

other.

Ground Fault Circuit

Interrupter (GFCI)

trips when machine

is plugged in.

FlexShaft Machine

wobbles or moves

while cleaning drain.

Motor does not turn

on with switch.

Troubleshooting

Cable assembly is being forced..

Incorrect FlexShaft Machine or chain

knocker used for pipe diameter.

Cable assembly exposed to acid/

corroded.

Cable/sheath worn out.

Cable assembly not properly

supported.

Chain knocker not properly set up/

adjusted.

Faulty REV/O-OFF/FOR switch.

Damaged power cord.

Short circuit in motor.

Faulty Ground Fault Circuit Interrupter

(GFCI).

Moisture in motor, switch box or on

plug.

Ground not level.

GFCI needs to be reset.

Thermal Overload has been tripped.

Do not force cable assembly. Follow

operating instructions.

Use correct FlexShaft Machine or chain

knocker for pipe size.

Clean cable assembly routinely.

Replace worn cable assembly.

Support cable assembly properly, see

instructions.

Properly set up/adjust chain knocker,

see instructions.

Have switch replaced. Take for service.

Have cord replaced. Take for service.

Take for service.

Have cord replaced. Take for service.

Take for service..

Operate in a clear, level and stable

location.

Reset GFCI.

Reset Thermal Overload.

should be taken to a RIDGID Authorized

Independent Service Center.

FlexShaft™ Drain Cleaning Machine

999-995-214.10_REV. A

18

Service and Repair

WARNING

Improper service or repair can make

the machine unsafe to operate.

The “Maintenance Instructions” will take

care of most of the service needs of this ma-

chine. Any problems not addressed by this

section should only be handled by a RIDGID

Authorized Independent Service Center. Use

only RIDGID service parts.

For information on your nearest RIDGID

Authorized In depen dent Service Center or

any service or repair questions see Contact

Information section in this manual.

Optional Equipment

WARNING

To reduce the risk of serious injury,

only use accessories specifically de-

signed and recommended for use with

the RIDGID FlexShaft Drain Cleaning

Machine, such as those listed.

For a complete listing of RIDGID equipment

avail

able f

or these tools, see the Ridge Tool

Cata log online at RIDGID.com or see Contact

Information.

Catalog

No. Description

66618 Knocker,

3

/

8

" cable, 3" pipe, 3 chain

66623 Knocker,

3

/

8

" cable, 4" pipe, 3 chain

66628 Knocker,

3

/

8

" cable, 6" pipe, 3 chain

66633 Knocker,

3

/

8

" cable, 3" pipe, 3 chain, carbide tip

66638 Knocker,

3

/

8

" cable, 4" pipe, 3 chain, carbide tip

66643 Knocker,

3

/

8

" cable, 6" pipe, 3 chain, carbide tip

66648 Knocker,

3

/

8

" cable, 3" pipe, 3 chain, carbide

w/penetrating head

66653 Knocker,

3

/

8

" cable, 4" pipe, 3 chain, carbide

w/penetrating head

66658 Knocker,

3

/

8

" cable, 6" pipe, 3 chain, carbide

w/penetrating head

64338 FlexShaft Lubricant, 8 oz, 12 per case

66663

3

/

8

" Assembly, cable, sheath, couplings, 125'

66668 FlexShaft

3

/

8

" sheath stock, 12"

Disposal

Parts of these tools contain valuable materi-

als and can be recycled. There are compa-

nies that specialize in recycling that may be

found locally. Dispose of the components in

compliance with all applicable regulations.

Contact your local waste management au-

thority for more information.

For EC Countries: Do not dispose

of electrical equipment with house-

hold waste!

According to the European Guideline

2012/19/EU for Waste Electrical and

Electronic Equipment and its imple-

mentation into national legislation,

electrical equipment that is no longer usable must

be collected separately and disposed of in an

environmentally correct manner.

La page charge ...

RIDGID 66658 Mode d'emploi

Ce manuel convient également à

RIDGID 66658 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents