Denon AVR-1403 Le manuel du propriétaire

Catégorie
Récepteurs AV
Taper
Le manuel du propriétaire

Ce manuel convient également à

AV SURROUND RECEIVER
AVR-1403/483
OPERATING INSTRUCTIONS
MODE D’EMPLOI
B
3
0
0
2
6
7
98
2
3
6
7
B
2
We greatly appreciate your purchase of this unit.
2
To be sure you take maximum advantage of all the
features this unit has to offer, read these instructions
carefully and use the set properly. Be sure to keep this
manual for future reference should any questions or
problems arise.
“SERIAL NO.
PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO
THE REAR OF THE CABINET FOR FUTURE REFERENCE”
“NO. DE SERIE
PRIERE DE NOTER LE NUMERO DE SERIE DE L’APPAREIL
INSCRIT A L’ARRIERE DU COFFRET DE FAÇON A POUVOIR
LE CONSULTER EN CAS DE PROBLEME.”
2
Nous vous remercions pour l’achat de cet appareil.
2
Pour être sûr de profiter au maximum de toutes les
caractéristiques qu’offre cet appareil, lire avec soin ces
instructions et bien utiliser l’appareil. Toujours
conserver ce mode d’emploi pour s’y référer
ultérieurement en cas de question ou de problème.
FOR ENGLISH READERS PAGE 2 ~ PAGE 47, 92, 93 POUR LES LECTEURS FRANCAIS PAGE 2, 48 ~ PAGE 93
2
ENGLISH
2 SAFETY PRECAUTIONS
2 NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION
Avoid high temperatures.
Allow for sufficient heat dispersion when
installed on a rack.
Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une étagère.
Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du
cordon.
Keep the set free from moisture, water, and
dust.
Protéger l’appareil contre l’humidité, l’eau et la
poussière.
Unplug the power cord when not using the set
for long periods of time.
Débrancher le cordon d’alimentation lorsque
l’appareil n’est pas utilisé pendant de longues
périodes.
* (For sets with ventilation holes)
Do not obstruct the ventilation holes.
Ne pas obstruer les trous d’aération.
Do not let foreign objects in the set.
Ne pas laisser des objets étrangers dans
l’appareil.
Do not let insecticides, benzene, and thinner
come in contact with the set.
Ne pas mettre en contact des insecticides, du
benzène et un diluant avec l’appareil.
Never disassemble or modify the set in any
way.
Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.
ATTENTION
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU
FOND.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
FRANCAIS
3
SAFETY INSTRUCTIONS
1. Read Instructions – All the safety and operating instructions
should be read before the product is operated.
2. Retain Instructions – The safety and operating instructions
should be retained for future reference.
3. Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions – All operating and use instructions should
be followed.
5. Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
6. Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7. Water and Moisture – Do not use this product near water – for
example, near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to the
product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product.
Any mounting of the product should follow the manufacturer’s
instructions, and should use a
mounting accessory
recommended by the
manufacturer.
9. A product and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the product and cart
combination to overturn.
10. Ventilation – Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
11. Power Sources – This product should be operated only from the
type of power source indicated on the marking label. If you are
not sure of the type of power supply to your home, consult your
product dealer or local power company. For products intended
to operate from battery power, or other sources, refer to the
operating instructions.
12. Grounding or Polarization – This product may be equipped with
a polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
13. Power-Cord Protection – Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where
they exit from the product.
15. Outdoor Antenna Grounding – If an outside antenna or cable
system is connected to the product, be sure the antenna or
cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article 810
of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See Figure A.
16. Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
17. Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
18. Overloading – Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of
fire or electric shock.
19. Object and Liquid Entry – Never push objects of any kind into
this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
20.
Servicing – Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
21.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service
personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance
– this indicates a need for service.
22. Replacement Parts – When replacement parts are required, be
sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics
as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
23. Safety Check – Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
24. Wall or Ceiling Mounting – The product should be mounted to a
wall or ceiling only as recommended by the manufacturer.
25. Heat – The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL
ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
4
ENGLISH
2 INTRODUCTION
2 ACCESSORIES
Thank you for choosing the DENON A/V Surround receiver. This remarkable component has been engineered to provide superb surround sound
listening with home theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite music sources.
As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the
contents of this manual before proceeding.
TABLE OF CONTENTS
Check that the following parts are included in addition to the main unit:
1
BEFORE USING
Pay attention to the following before using this unit:
Moving the set
To prevent short circuits or damaged wires in the connection cords,
always unplug the power cord and disconnect the connection
cords between all other audio components when moving the set.
Before turning the power operation switch on
Check once again that all connections are proper and that there are
not problems with the connection cords. Always set the power
operation switch to the standby position before connecting and
disconnecting connection cords.
Store this instructions in a safe place.
After reading, store this instructions along with the warranty in a
safe place.
Note that the illustrations in this instructions may differ from
the actual set for explanation purposes.
V. AUX terminal
The AVR-1403/483’s front
panel is equipped with a V.
AUX terminal. Remove the
cap covering the terminal
when you want to use it.
z
Before Using ..............................................................................................4
x
Cautions on Installation ..............................................................................5
c
Cautions on Handling .................................................................................5
v
Features......................................................................................................5
b
Part Names and Functions.....................................................................6, 7
n
Read this first .............................................................................................8
m
Setting up the Speaker Systems................................................................8
,
Connections .........................................................................................9~14
.
Using the Remote Control Unit................................................................15
⁄0
Setting up the System .......................................................................16~20
⁄1
Remote Control Unit..........................................................................21~23
⁄2
Operation ...........................................................................................24~28
⁄3
Surround.............................................................................................29~33
⁄4
DSP Surround Simulation...................................................................34~38
⁄5
Listening to the Radio……………………………………………………39~41
⁄6
Last Function Memory .............................................................................42
⁄7
Initialization of the Microprocessor.…………………………………………42
⁄8
Additional Information........................................................................43~45
⁄9
Troubleshooting ........................................................................................46
¤0
Specifications .…………………………………………………………………47
List of Preset Codes..................................................................................92, 93
q Operating instructions ............................................................................1
w Warranty ( for North America model only ) ............................................1
e Service station list...................................................................................1
r Remote control unit (RC-896).................................................................1
rt y u
B
t R6P/AA batteries ....................................................................................2
y AM loop antenna ....................................................................................1
u FM indoor antenna..................................................................................1
5
ENGLISH
3
CAUTIONS ON HANDLING
4
FEATURES
Switching the input function when input jacks are not
connected
A clicking noise may be produced if the input function is switched
when nothing is connected to the input jacks. If this happens,
either turn down the MASTER VOLUME control or connect
components to the input jacks.
Muting of PRE OUT jack, HEADPHONE jack and SPEAKER
terminals
The PRE OUT jack, HEADPHONE jack and SPEAKER terminals
include a muting circuit. Because of this, the output signals are
greatly reduced for several seconds after the power operation
switch is turned on or input function, surround mode or any other
set-up is changed.
If the volume is turned up during this time, the output will be very
high after the muting circuit stops functioning. Always wait until
the muting circuit turns off before adjusting the volume.
Whenever the power operation switch is in the STANDBY
state, the apparatus is still connected on some AC line
voltages.
Please be sure to unplug the cord when you leave home for,
say, a vacation.
1. Dolby Pro Logic II decoder
Dolby Pro Logic II is a new format for playing multichannel audio
signals that offers improvements over conventional Dolby Pro
Logic. It can be used to decode not only sources recorded in
Dolby Surround but also regular stereo sources into five channels
(front left/right, center and surround left/right). In addition, various
parameters can be set according to the type of source and the
contents, so you can adjust the sound field with greater precision.
2. Dolby Digital decoder
Dolby Digital, a digital discrete system in which the different
channels are completely independent, recreates “three-
dimensional” sound fields (sounds with a sense of distance,
movement and position) with no crosstalk between channels for
greater reality. In addition, the 5 channels (excluding the 0.1
channel for low frequency effects) have a playback range
extending to 20 kHz, the same as the range of CDs, thus resulting
in clearer, more richly expressive sound.
3. DTS (Digital Theater Systems)
DTS provides up to 5.1 channels of wide-range, high fidelity
surround sound, from sources such as laser disc, DVD and
specially-encoded music discs.
4. High performance DSP simulates 7 sound fields
Playback is possible in 7 surround modes: 5-channel Stereo, Mono
Movie, Rock Arena, Jazz Club, Video Game, Matrix and Virtual.
You can enjoy a variety of sound effects for different movie
scenes and program sources even with stereo sources not in
Dolby Surround.
5. Personal Memory Plus function
Personal Memory Plus is an advanced version of Personal
Memory. With Personal Memory Plus, the set automatically
memorizes the surround mode, channel volume, surround
parameters, etc., for each of the separate input sources.
6. Remote control unit with pre-memory function
This unit comes with a remote control unit equipped with a pre-
memory function. The remote control command codes for
DENON remote controllable AV components as well as for LD
players, video decks, TVs, etc., of other major manufacturers are
prestored in the memory.
7. 6CH EXT. IN jack
This unit is equipped with 6CH EXT. IN jacks for use with audio
formats of the future.
2
CAUTIONS ON INSTALLATION
Noise or disturbance of the picture may be generated if this unit or
any other electronic equipment using microprocessors is used near a
tuner or TV.
If this happens, take the following steps:
Install this unit as far as possible from the tuner or TV.
Set the antenna wires from the tuner or TV away from this unit’s
power cord and input/output connection cords.
Noise or disturbance tends to occur particularly when using indoor
antennas or 300 /ohms feeder wires. We recommend using
outdoor antennas and 75 /ohms coaxial cables.
For heat dispersal, leave at least 0.3 ft (10 cm) of space between
the top, back and sides of this unit and the wall or other
components.
B
0.3 ft (10 cm) or more
wall
0.3 ft (10 cm) or more
6
ENGLISH
5
PART NAMES AND FUNCTIONS
Front Panel
For details on the functions of these parts, refer to the pages given in parentheses ( ).
B
q w te ur
y i!2
!9@0
@1@2@3
@4
@5
@6
@7@8@9
!0 !1 !3 !4 !5o
!6!8 !7#0
q
Power operation switch ..............................................(17, 24, 39)
w
Headphones jack (PHONES)....................................................(27)
e
Preset station selector buttons ...............................................(41)
r
SPEAKER A/B buttons.................................................(24, 27, 42)
t
INPUT MODE button...................................................(25, 28, 32)
y
ANALOG button ................................................................(25, 28)
u
EXT. IN button ...................................................................(25, 28)
i
TONE DEFEAT button ............................................................(26)
o
VIRTUAL SURROUND button .....................................(34, 35, 37)
!0
VIDEO SELECT button ............................................................(27)
!1
V. AUX INPUT jacks.............................................................(4, 11)
!2
SURROUND MODE button...................................(26, 30, 32, 37)
!3
SURROUND PARAMETER button...........................................(37)
!4
SELECT UP/DOWN button .............................(26, 29, 30, 32, 37)
!5
TONE CONTROL button..........................................................(26)
!6
CH VOL button ........................................................................(29)
!7
MASTER VOLUME control......................................................(26)
!8
STATUS button ........................................................................(27)
!9
DIMMER button ......................................................................(27)
@0
Master volume indicator (VOLUME LEVEL)............................(26)
@1
Display
@2
TUNING UP/DOWN button .....................................................(40)
@3
MEMORY button...............................................................(39, 41)
@4
MODE button ..........................................................................(40)
@5
BAND button ...........................................................................(40)
@6
SIGNAL indicators....................................................................(26)
@7
INPUT mode indicators............................................................(26)
@8
Remote control sensor (REMOTE SENSOR) ..........................(15)
@9
Power operation indicator
#0
Input source selector buttons ...........................................(25, 32)
7
ENGLISH
Remote control unit
For details on the functions of these parts, refer to the pages given in parentheses ( ).
B
DVD/VDP
CD
TV/DBS
VCR
SURROUND
MODE
TUNER SHIFT
REMOTE CONTROL UNIT RC-896
STATUS MUTING
T.TONE
MASTER
VOL
TITLE
DISC SKIP+
V. AUX
INPUT MODE CDR / TAPE
CHANNEL TV
CD·MD/CDR·DVD/VDP
VIDEO SELECT
SYSTEM
SET UP MENU
SELECT
RETURN DISPLAY
SURROUND
CH SELECT
VOLUME
CHANNEL
AVR/AVC
DVD/VDP
TV VCR
AUDIO
CD
MD/CDR
VIDEO
POWER
TAPE
·
VCR
OFF
8
4
9
5
1
0
6
2
7
3
ON
3
0
0
2
6
7
98
2
3
6
7
INPUT MODE button ...................(25, 28)
Cursor buttons.......................(16, 32, 35)
System buttons (TV) ..........................(23)
Test tone button.................................(29)
Remote control signal
transmitter .........................................(15)
Master volume control
buttons...............................................(26)
POWER buttons ..........................(22, 23)
MUTING button .................................(27)
Mode selector switch............(16, 21, 22)
Input source selector
buttons.........................................(25, 32)
Preset station select
buttons.........................................(21, 41)
System buttons
(CD, MD/CDR, DVD/VDP) ............(21, 23)
SYSTEM (SYSTEM SET UP)
buttons...............................................(16)
System buttons (TAPE, VCR)
buttons.........................................(21, 23)
SURROUND MODE
button ........................(26, 29, 30, 32, 35)
SURROUND (SURROUND PARAMETER)
button...........................................(32, 35)
STATUS button...................................(27)
8
ENGLISH
6
READ THIS FIRST
This AV Surround Receiver must be setup before use. Following these steps.
2 Speaker system layout
Basic system layout
The following is an example of the basic layout for a system consisting of six speaker systems and a television monitor:
Subwoofer Center speaker system
Surround speaker systems
Front speaker systems
Set these at the sides of the TV or screen with
their front surfaces as flush with the front of the
screen as possible.
7
SETTING UP THE SPEAKER SYSTEMS
Step 3 (page 16 to 20)
Finally, setting up the system.
Step 2 (page 15)
Next, insert the batteries into the remote control unit.
Step 1 (page 8 to 14)
Choose the best location to setup the Speakers and connecting the components.
9
ENGLISH
8
CONNECTIONS
Do not plug in the power cord until all connections have been
completed.
Be sure to connect the left and right channels properly (left with
left, right with right).
Insert the plugs securely. Incomplete connections will result in
the generation of noise.
Use the AC OUTLET for audio equipment only. Do not use
it for hair driers, etc.
Note that binding pin plug cords together with power cords or
placing them near a power transformer will result in generating
hum or other noise.
Noise or humming may be generated if a connected audio
equipment is used independently without turning the power
of this unit on. If this happens, turn on the power of the this
unit.
Connecting the audio components
LINE OUT
SURROUND
SUB WOOFER
CENTER
FRONT
LINE OUT
LINE OUT
LINE IN
R
OUTPUTINPUT
LRL
R
OUTPUT
L
R
L
R
L
R
L
L
R
L
R
R
L
R
L
L
R
DIGITAL AUDIODIGITAL AUDIO
OUTPUT
OPTICAL
B
Connecting a CD player
Connect the CD player’s analog
output jacks (ANALOG OUTPUT) to
this unit’s CD jacks using pin plug
cords.
Decoders with 6-channel
analog outputs, etc.
DIGITAL jacks
Use these for connections to audio equipment with digital output. Refer
to Page 20 for instructions on setting this terminal.
Connecting the AC OUTLET
AC OUTLET
• SWITCHED
(total capacity – 120 W (1 A.))
The power to this outlet is turned on and off in conjunction with the
POWER switch on the main unit, and when the power is switched
between on and standby from the remote control unit.
No power is supplied from this outlet when this unit’s power is at
standby. Never connect equipment whose total capacity is above 120
W (1 A.)
NOTE:
Only use the AC OUTLET for audio equipment. Never use it for hair
driers, TVs or other electrical appliances.
AC CORD
AC 120V, 60Hz
Connect the internal amplifier’s subwoofer to the subwoofer
terminal. (Refer to page 13.)
Connecting a tape deck
Connections for recording:
Connect the tape deck’s recording input jacks (LINE IN or
REC) to this unit’s tape recording (OUT) jacks using pin plug
cords.
Connections for playback:
Connect the tape deck’s playback output jacks (LINE OUT or
PB) to this unit’s tape playback (IN) jacks using pin plug cords.
CD player
Tape deck or CD recorder
Use 75 /ohms cable pin cords (sold separately) for coaxial
connections.
• Use optical cables (sold separately) for optical connections.
Subwoofer jack
CD recorder, MD recorder or other component
equipped with digital output lacks.
10
ENGLISH
Connecting the video equipments
To connect the video signal, connect using a 75 /ohms video signal cable cord. Using an improper cable can result in a drop in sound quality.
IN
VIDEO
R
L
R
L
R
L
L
R
R OUT IN
AUDIO
VIDEO
OUT IN
LRL
R
L
R
L
R OUT
VIDEO
OUT
L
AUDIO
OUT
COAXIAL
DIGITAL
L
R
R OUT
VIDEO
OPTICAL
OUT
L
AUDIO
OUT
DIGITAL
L
R
TV or DBS tuner
DVD player or VDP
Monitor TV
Connecting a TV/DBS tuner
TV/DBS
• Connect the TV’s or DBS tuner’s video output jack (VIDEO
OUTPUT) to the (yellow) TV/DBS IN jack using a 75
/ohms video coaxial pin plug cord.
• Connect the TV’s or DBS tuner’s audio output jacks (AUDIO
OUTPUT) to the TV/DBS IN jacks using pin plug cords.
AUDIO
VIDEO
Connecting a DVD player or a video disc player (VDP)
• Connect the DVD player’s (video disc player’s) video output jack (VIDEO OUTPUT) to
the (yellow) DVD/VDP IN jack using a 75 /ohms video coaxial pin plug cord.
Connect the DVD player’s (video disc player’s) analog audio output jacks (ANALOG
AUDIO OUTPUT) to the DVD/VDP IN jacks using pin plug cords.
For better sound quality, we recommend using the DVD player with digital rather than
analog connections.
DVD and VDP players can also be connected to the VCR terminals.
AUDIO
VIDEO
MONITOR OUT
• Connect the TV’s video input jack (VIDEO
INPUT) to the MONITOR OUT
jack using a 75 /ohms video coaxial pin
plug cord.
VIDEO
NOTE:
Connection of the video disc Player Equipped with Dolby Digital RF
(AC-3RF) Output Jack.
• Please use a commercially available adaptor when connecting the
Dolby Digital RF (AC-3RF) output jack of the video disc player to
the digital input jack.
Please refer to the instruction manual of the adapter when making
connections.
Video deck
Video input/output connections:
Connect the video deck’s video output jack (VIDEO OUT) to the (yellow) VCR IN jack, and the video deck’s video input jack (VIDEO IN) to the
(yellow) VCR OUT jack using 75 /ohms video coaxial pin plug cords.
Connecting the audio output jacks:
• Connect the video deck’s audio output jacks (AUDIO OUT) to the VCR IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the VCR OUT
jacks using pin plug cords.
AUDIOAUDIO
VIDEOVIDEO
Connecting a video decks
VIDEO OUT
VIDEO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
VIDEO OUT
AUDIO OUT
AUDIO OUT
AUDIO IN
11
ENGLISH
R VIDEO OUTL
AUDIO VIDEO
R VIDEO OUTL
AUDIO VIDEO
L
R
L
R
L
R
Connecting a Video game equipment
Connect the Video game equipment’s output jacks
to this unit’s V. AUX INPUT jacks.
Video game
Video camera
Connecting a Video camera equipment
Connect the video camera equipment’s output
jacks to this unit’s V. AUX INPUT jacks.
The V. AUX terminal is covered with a cap. Remove this cap in order to use the terminal. (See page 4 for instructions on removing the cap.)
12
ENGLISH
1
4
2
3
Connecting the antenna terminals
DIRECTION OF
BROADCASTING
STATION
AM LOOP
ANTENNA
(An Accessory)
FM ANTENNA
GROUND
AM OUTDOOR
ANTENNA
FM INDOOR ANTENNA
(An Accessory)
75 /ohms
COAXIAL
CABLE
AM loop antenna assembly
Connect to the AM
antenna terminals.
Bend in the reverse
direction.
Remove the vinyl tie
and take out the
connection line.
a. With the antenna
on top any stable
surface.
b. With the antenna
attached to a
wall.
Mount
Installation hole
Mount on wall, etc.
Connection of AM antennas
1. Push the lever. 2. Insert the
conductor.
3. Return the lever.
Note to CATV system installer:
This reminder is provided to call the CATV system installers
attention to Article 820-40 of the NEC which provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
Notes:
Do not connect two FM antennas simultaneously.
Even if an external AM antenna is used, do not disconnect
the AM loop antenna.
Make sure AM loop antenna lead terminals do not touch
metal parts of the panel.
13
ENGLISH
Speaker system connections
Connect the speaker terminals with the speakers making sure that like
polarities are matched (< with <, > with >). Mismatching of polarities will
result in weak central sound, unclear orientation of the various instruments,
and the sense of direction of the stereo being impaired.
When making connections, take care that none of the individual conductors
of the speaker cord come in contact with adjacent terminals, with other
speaker cord conductors, or with the rear panel.
Speaker Impedance
When speaker systems A and B are use separately, speakers with an
impedance of 6 to 16 /ohms can be connected for use as front speakers.
Be careful when using two pairs of front speakers (A + B) at the same time,
since use of speakers with an impedance of 12 to 16 /ohms.
Speakers with an impedance of 6 to 16 /ohms can be connected for use
as center and surround speakers.
The protector circuit may be activated if the set is played for long periods of
time at high volumes when speakers with an impedance lower than the
specified impedance are connected.
NOTE:
NEVER touch the speaker terminals when the power is on. Doing so
could result in electric shocks.
Do not use soeaker cords with a diameter of over 1.5 mm. Doing so
may damage the speaker terminals. (for FRONT SPEAKER B,
SURROUND SPEAKER)
Connecting the speaker cords
1. Loosen by turning
counterclockwise.
2. Insert the cord. 3. Tighten by turning
clockwise.
Connecting banana plugs
Turn clockwise to tighten, then insert the
banana plug.
(
L
)(
R
)
(
L
) (
R
)(
L
) (
R
)
Connection jack for subwoofer with built-in
amplifier (super woofer), etc.
To achieve Dolby Digital (AC-3) playback
effect, use a unit that can sufficiently
reproduce frequencies of under 80 Hz.
SURROUND SPEAKER SYSTEMS
CENTER SPEAKER SYSTEM
FRONT SPEAKER SYSTEMS
Precautions when connecting speakers
If a speaker is placed near a TV or video monitor, the
colors on the screen may be disturbed by the
speaker’s magnetism. If this should happen, move
the speaker away to a position where it does not
have this effect.
banana plug
1. Push the lever. 2. Insert the cord. 3. Return the lever.
System B
FRONT SPEAKER SYSTEMS
System A
14
ENGLISH
Protector circuit
This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under
circumstances such as when the output of the power amplifier is inadvertently short-circuited and a large current flows,
when the temperature surrounding the unit becomes unusually high, or when the unit is used at high output over a long
period which results in an extreme temperature rise.
When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED flashes. Should
this occur, please follow these steps: be sure to switch off the power of this unit, check whether there are any faults with
the wiring of the speaker cables or input cables, and wait for the unit to cool down if it is very hot. Improve the ventilation
condition around the unit and switch the power back on.
If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the
unit, switch off the power and contact a DENON service center.
Note on speaker impedance
The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with
an impedance lower than the specified impedance (for example speakers with an impedance of lower than 4 /ohms)
are connected. If the protector circuit is activated, the speaker output is cut off. Turn off the sets power, wait for the set
to cool down, improve the ventilation around the set, then turn the power back on.
15
ENGLISH
9
USING THE REMOTE CONTROL UNIT
Following the procedure outlined below, insert the batteries before using the remote control unit.
Range of operation of the remote control unit
Inserting the batteries
B
B
Point the remote control unit at the remote control sensor as shown
on the diagram at the left.
NOTES:
The remote control unit can be used from a straight distance of
approximately 23 feet/7 meters, but this distance will shorten or
operation will become difficult if there are obstacles between the
remote control unit and the remote control sensor, if the remote
control sensor is exposed to direct sunlight or other strong light, or
if operated from an angle.
Neon signs or other devices emitting pulse-type noise nearby may
result in malfunction, so keep the set as far away from such
devices as possible.
Approx. 23 feet/7 m
30°
30°
w Insert the R6P/AA batteries properly, as
shown on the diagram.
q Press as shown by the arrow and slide
off.
e Close the lid.
NOTES:
Use only R6P/AA batteries for replacement.
Be sure the polarities are correct. (See the illustration inside the battery compartment.)
Remove the batteries if the remote control transmitter will not be used for an extended period of time.
If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the
battery compartment thoroughly before installing new batteries.
Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the time comes.
Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is
operated nearby the set. (The included battery is only for verifying operation. Replace it with a new battery as soon as possible.)
16
ENGLISH
10
SETTING UP THE SYSTEM
Once all connections with other AV components have been completed as described in CONNECTIONS (see pages 9 to 14), make the
various settings described below on the display.
These settings are required to set up the listening rooms AV system centered around the this unit.
STATUS MUTING
T.TONE
MASTER
VOL
TITLE
DISC SKIP+
CD·MD/CDR·DVD/VDP
VIDEO SELECT
SYSTEM
SET UP MENU
RETURN DISPLAY
SURROUND
98
2
3
6
7
SELECT
CH SELECT
SYSTEM SETUP button
Press this to display the system setup on the display.
CURSOR buttons (, ª, 0, 1)
Press this change what appears on the display.
SELECT button
Press this to switch the display.
Also use this button to complete the setting.
System setup items and default values (set upon shipment from the factory)
System setup Default settings
Speaker
Configuration
Subwoofer Mode
Digital Input
Input the combination of speakers in your system and their
corresponding sizes (SMALL for regular speakers, LARGE for full-size,
full-range) to automatically set the composition of the signals output
from the speakers and the frequency response.
This assigns the digital input jacks for the different input
sources.
Input
source
Digital
Inputs
Front Sp.
Large
Center Sp. Surround Sp. Sub Woofer
Small Small Yes
Front & Subwoofer Center Surround L & R
12 ft (3.6 m) 12 ft (3.6 m) 10 ft (3.0 m)
DVD/VDP TV/DBS
COAXIAL OPTICAL
Delay Time
This parameter is for optimizing the timing with which the audio
signals are produced from the speakers and subwoofer according to
the listening position.
1
Set the slide switch to AUDIO.
2
Use the following buttons to set up the system:
AUDIO
CD
MD/CDR
VIDEO
This selects the subwoofer speaker for playing deep bass
signals.
Subwoofer mode = Normal
NOTE:
The system setup is not displayed when HEADPHONE ONLY is selected.
17
ENGLISH
Before setting up the system
1
2
Press the SYSTEM button to enter the setting.
Check that all the components are correct, then press the POWER operation switch on the main unit or
the POWER button on the remote control unit to turn on the power.
3
Press the SELECT or (down) button to switch to the speaker configuration set up.
*SYSTEM SET UP
NOTE:
Press the SYSTEM button again to finish system set up. System set up can be finished at any time. The changes to the settings made up to
that point are entered.
NOTE: Please make sure the AUDIO position of the slide switch on the remote control unit.
(Main unit) (Remote control unit)
Setting the speaker configuration
1
Use the (left) and (right) buttons to select your front speaker type.
1 FRONT LARGE
LARGE
SMALL
(left) button (right) button
Press the SELECT or (down) button to switch to the center speaker setting.
2
Use the (left) and (right) buttons to select your center speaker type.
2 CENTER SMALL
LARGE
SMALL
NONE
(left) button (right) button
Press the SELECT or (down) button to switch to the surround speaker setting.
3
Use the (left) and (right) buttons to select your surround speaker type.
3 SURR. SMALL
LARGE
SMALL
NONE
(left) button (right) button
Press the SELECT or (down) button to switch to the subwoofer setting.
NOTE:
When Small has been selected for the front speakers, Large cannot be selected for the center speaker.
(Initial)
(Initial)
(Initial)
18
ENGLISH
NOTE:
When Small has been selected for the front speakers, Large cannot be selected for the surround speakers.
4
Use the (left) and (right) buttons to select your subwoofer setting.
4 S.WOOFER YES
YES
NO
(left) button (right) button
Press the SELECT or (down) button to enter the settings and switch to the SUBWOOFER MODE
setting.
Parameters
Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.
Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient volume. When this setting is
selected, low frequencies of below 80 Hz are assigned to the subwoofer.
None…… Select this when no speakers are installed.
Yes/No. Select Yes when a subwoofer is installed, No when its not installed.
NOTE:
Select Large or Small not according to the physical size of the speaker, but according to the bass reproduction capacity at 80 Hz. If you cannot
determine the best setting, try comparing the sound when set to Small and when set to Large, at a level that will not damage the speakers.
Caution:
In case the subwoofer is not used, be sure to set Subwoofer = No, or the bass sound of front channel is divided to subwoofer channel and
not reproduced in some mode.
Setting the SUBWOOFER MODE
1
Use the (left) and (right) buttons to select the Subwoofer mode.
5 SW MODE NORM
NORM +MAIN
(left) button (right) button
Press the SELECT or (down) button to enter the setting and switch to the SPEAKER DISTANCE
setting.
NOTES:
Assignment of low frequency signal range
The signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or DTS signals) and the low frequency
signal range of channels set to SMALL in the setup. The low frequency signal range of channels set to LARGE are produced from those
channels.
Subwoofer mode
The subwoofer mode setting is only valid when LARGE is set for the front speakers and YES is set for the subwoofer in the Speaker
Configuration settings (see pages 17, 18).
If SMALL is set for the front speakers or NO is set for the subwoofer, the subwoofer mode setting does not affect playback of low
frequency signal range.
When the +MAIN playback mode is selected, the low frequency signal range of channels set to LARGE are produced simultaneously
from those channels and the subwoofer channel.
In this playback mode, the low frequency range expand more uniformly through the room, but depending on the size and shape of the room,
interference may result in a decrease of the actual volume of the low frequency range.
When the NORM playback mode is selected, the low frequency signal range of channels set to LARGE are only produced from those
channels. In this playback mode there tends to be little interference of the low frequency range in the room.
Try playing the music or movie source and select the playback mode providing the stronger low frequency range sound.
(Initial)
(Initial)
19
ENGLISH
Setting the speaker distance
Input the distances from the listening position to the speakers and set the surround delay time.
Preparations:
Measure the distances from the listening position to the speakers (L1 to L3 on the diagram at the right).
L1: Distance from center speaker to listening position
L2: Distance from front speakers to listening position
L
3: Distance from surround speaker to listening position
CAUTION:
Set the center speaker at the same distance from the front speakers (left and right) or the subwoofer,
or so that the difference in distance (L2 L1) is 5 feet or less.
Set the surround speakers (left and right) at the same distance from the front speakers (left and right)
or the subwoofer, or so that the difference in distance (L2 L3) is 15 feet or less.
FL
Center FR
Listening
position
SL
SR
1
Use the (left) and (right) buttons to set the distance from the front speakers and subwoofer to the
listening position.
6 FRNT/SW 12ft
The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest
to the measured distance.
(/SW appears only when subwoofer = yes.)
Press the SELECT or (down) button to switch to the center speaker setting.
NOTE:
The speaker distance can be adjusted between 0 and 60 feet in steps of 1 foot.
2
Use the (left) and (right) buttons to set the distance from the center speakers to the listening
position.
7 CENTER 12ft
The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest
to the measured distance.
Press the SELECT or (down) button to switch to the surround speaker setting.
NOTE:
No setting when None has been selected for the center speaker.
3
Use the (left) and (right) buttons to set the distance from the surround speakers to the listening
position.
8 SURR. 10ft
The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest
to the measured distance.
Press the SELECT or (down) button to enter the setting and switch the DIGITAL input (COAX) setting.
NOTE:
No setting when None has been selected for the surround speakers.
20
ENGLISH
Digital input setup
Input the type of components connected to the digital input terminals.
1
Use the (left) and (right) buttons to set the type of device connected to the COAXIAL input (COAXIAL)
terminal.
9 COAX DVD
CD DVD TV VCR V.AUX CDR OFF
Select OFF if nothing is connected.
Press the SELECT or (down) button to switch the optical input (OPT) setting.
(left) button (right) button
2
Use the (left) and (right) buttons to set the type of device connected to the OPTICAL input (OPTICAL)
terminal.
10 OPT TV
CD DVD TV VCR V.AUX CDR OFF
Select OFF if nothing is connected.
Press the SELECT or (down) button if you want to start the settings over from the beginning.
(left) button (right) button
NOTE:
TUNER cannot be selected.
After setting up the system
1
Press the SYSTEM button to finish system set up.
This completes the system setup operations. Once the system is set up, there is no need to make the settings again unless other components
or speakers are connected to or the speaker layout is changed.
(Initial)
(Initial)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94

Denon AVR-1403 Le manuel du propriétaire

Catégorie
Récepteurs AV
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues