GE WCVH6800J1WW Owner's Manual and Installation Instructions

0

ge.com

Safety Instructions ............ 2,s

Operating Instructions

Cleaning the Washer ............. 11-13

Control Panels ..................... 4-5

Control Settings .................... 6-7

Features ......................... 8-10

Loading and Using the Washer ....... 10

Installation Instructions ..... 14-19

Drain Requirements ................. 17

Electrical Requirements .............. 17

Installing the Washer ............. 18, 19

Location of Your Washer ............. 15

Preparing to Install Your Washer ...... 14

Replacement Parts .................. 19

Rough-In Dimensions ................ 15

Unpacking Your Washer ............. 16

Water Supply Requirements .......... 17

Troubleshooting Tips ........ 20-22

Consumer Support

Service Telephone Numbers . Back Cover

Warrants (Canada) ................. 2/4

Warrants (U.S.) ..................... 23

Laveuses

La section frangaise commence _ la page 25

Lavadoras

La secci6n en espahol empieza en la p6gina 51

ENERGYSTAR

As an ENERGYSTAR®partner,

GEhas determined that this

product meets the ENERGYSTAR®

guidelines for energy efficiency.

Write the model and serial

numbers here:

Model #

Serial #

Youcan find them on a labelon the

sideof the washeE

175DI807P607 49-90339

12-07JR

IMPORTANT SAFETY INFORHATION.

READ ALL INSTRUCTIONS BEFORE USING.

WAR NING! _oryoursafety,the_nformat_on_nth_smanualmustbefollowedtom_n_m_zether_sk

of fire orexplosion, electric shock, or to prevent property damage, personal injury or

loss of life.

The instructions in this manual and all other literature included with this washer are

not meant to cover every possible condition and situation that may occun Good, safe

practices and caution MUSTbe applied when installing, operating and maintaining

any appliance.

WATERHEATERSAFETY

Undercertain conditions,hydrogen gas may beproduced in a water heater that has not been usedfor two weeks

or more.Hydrogen gascan beexplosiveunder these cimumstonces.

Ifthe hotwater hasnot been usedfor two weeksor more, preventthe possibilityof damage or injury by

turning on all hot water faucets and allowingthem to run for severalminutes. Dothis before using ang electrical

appliancewhich isconnectedto the hotwater system.Thissimpleprocedurewill allow any built-up hydrogen

gasto escape.Sincethe gasisflammable, do not smokeor usean openflame or appliance during this process.

PROPERINSTALLATION

Thiswasher must be properly installedand located in accordancewith the Installation Instructions beforeit isused.

II Installor storewhere itwill notbe exposed II Properlygroundwasherto conformwith all governing

to temperaturesbelowfreezingor exposed codesand ordinances.Followdetailsin Installation

to the weather,which couldcausepermanent Instructions.

damage and invalidatethe warranty.

YOURLAUNDRYAREA

• Keep the urea underneath and around your

appliances free of combustible materials such as

lint, paper, rags and chemicals.

• Closesupervision isnecessary if this appliance is

used by or nearchildren. Do not allow children to

play on,with or insidethisor any other appliance.

ge.com

WHEN USINGTHEWASHER

• Never reach into washer while it is moving. • Never attempt to operate this appliance

Wait until the machine has completely stopped if it is damaged, malfunctioning, partially

before opening the door. disassembled, or has missing or broken parts,

Do not mix chlorine bleach with ammonia including a damaged cord or plug.

or acids such as vinegar and/or rust remover. • Do not slam the washer door closed. Do not tru

Mixing different chemicals can produce a toxic to force the door open when locked (LOCKED

gas which may cause death, indicator ON).This could result in damage to

the washeE

Do not wash or dry articles that have been

Use this •

appliance

on!y for its

intended

purpose as

described in •

this Owner's

Manual

cleaned in, washed in, soaked in or spotted •

with combustible or explosive substances (such as

wax, oil, paint, gasoline, degreasers, dru-cleaning

solvents, kerosene, etc.)which mag ignite or

explode. Do not add these substances to the

wash water. Do not use or place these substances

around gour washer or drger during operation.

The laundry process can reduce the flame

retardancg of fabrics. To avoid such a result,

carefully follow the garment manufacturer's

wash and care instructions.

The washer is equipped with an electrical

overload protector. The motor will stop

if it becomes overheated. The washer will

automaticallg restart after a cool-down

period of up to 2 hours, if the washer

has not been manuallg turned off

during this time.

To minimize the possibility of electric shock,

unplug this appliance from the power supplg

or disconnect the washer at the building's

distribution panel bg removing the fuse or

switching off the circuit breaker before attempting

ang maintenance or cleaning. NOTE:Pressing the

power button does NOTdisconnect the appliance

from the power supplg.

WHEN NOT IN USE

• Turn off water faucets to relieve pressure on

hoses and valves and to minimize leakage if

a break or rupture should occur. Check the

condition of the fill hoses; GErecommends

changing the hoses everg 5 gears.

• Before discarding a washer, or removing it

from service, remove the washer door to prevent

children from hiding inside.

• Do not attempt to repair or replace ang part of

this appliance unless specificallg recommended

in this Owner's Manual, or in published user-repair

instructions that gou understand and have the

skillsto carrg out.

• Do not tamper with controls.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY

SAVE THESEINSTRUCTIONS

About the washer control panel.

Find the illustration that closely matches your model and see the cycle descriptions starting on page 6 for details.

(Onsome

models)

I

o

®

.(

o

)-

ge.com

About the washer control panel.

O Power

Pressto "wake up" the display, If the display is active, press to put the washer into standby mode,

NOTE:Pressing POWER does not disconnect the appliance from the power supply,

0

Wash Cgcles

The wash cycles are optimized for specific types of wash loads, The chart below will help you match

the wash setting with the loads, The GentleCleanTM lifters lightly tumble the clothes into the water and

detergent solution to clean the load,

WHITES For heavily to lightly soiled white cottons, household linens, work and play clothes.

COLORS/NORMAL For heavy to lightly soiled colorfast cottons, household linens, work and play

clothes.

STAINWASH For heavy soiled colorfast cottons, household linens, work and play clothes.

EASYCARE Forwrinkle-free and permanent press items.

(PERMAPRESS)

ACTIVEWEAR For active sports, exercise and some casual wear clothes, Fabrics include modern

(some models) technology finishes and fibers such as spandex, stretch and micro-fibers.

DELICATES For lingerie and special-care fabrics with light to normal soil. Provides gentle

(some models) tumbling and soak during wash and rinse.

HANDWASH For items labeled hand-washable with light soils. Provides gentle rocking to mimic

the handwashing action.

WASHABLE Forthe washing of machine washable wool products, provided that they are

WOOLS washed according to the instructions on the garment label. When selecting this

(some models) cycle, you must use a detergent suitable for washing wool.

PlY CYCLE Pressto use, create or modify custom wash cycles,

(some models)

SPEEDWASH For lightly soiled items that are needed in a hurry. Cycle time is approximately

30 minutes, depending on selected options.

DRAIN &SPIN Drain and spin at any time.

RINSE& SPIN To quickly rinse out any items at any time.

O

0

O

ge.com

Sail Level

Changing the SOILLEVELincreases or decreases the wash time to remove different amounts of soil.

To change the SOILLEVEL,press the SOILLEVEL button until you have reached the desired setting.

You can choose between Extra Light, Light, Normal or Heavy soil.

Spin Speed

Changing the SPINSPEEDchanges the final spin speed of the cycles. Always follow the fabric

manufacturer's care label when changing the SPINSPEED.

To change the SPIN SPEED,press the SPIN SPEEDbutton until you have reached the desired setting.

Higher spin speeds are not available on certain cycles, such as Delicates.

Higher spin speeds remove more water from the clothes and will help reduce dry time, but may also

increase the possibility of setting wrinkles on some fabrics.

Wash Temp

Adjust to select the proper water temperature for the wash cycle. The prewash and rinse water is

always cold to help reduce energy usage and reduce setting of stains and wrinkles.

Follow the fabric manufacturer's care label when selecting the wash temperature.

To change the wash temperature, press the WASH TEMPbutton until you have reached the desired

setting. The Sanitized wash temperature is not available on certain cgcles, such as Delicates.

When selecting the Sanitize wash temperature, the washer increases the water temperature

to sanitize and kill more than 99% of many common bacteria found in home laundry. The sanitize

wash temperature is only available on Stain Wash and Whites wash cgcles. For best results, select

the heavy soil setting when using the Sanitize wash temperature setting.

NOTE:Thefirst 10 seconds of the wash fill is always cold. This feature assists in conditioning the fabric

and preventing stains from setting on garments.

START/PAUSE

Pressto start a wash cycle. If the washer is running, pressing it once will pause the washer and unlock

the dooE Press again to restart the wash cycle.

NOTE:tf the washer is paused and the cycle is not restarted within 2 hours, the current wash cycle will

be cancelled.

NOTE:The washer performs automatic system checks after pressing the STARTbutton. Water will flow

in/45 seconds or less.You may hear the door lock and unlock before water flows; this is normal.

About the washer features.

NOTE:Features mag not be available on all washer models.

Cycle Signal

Usethe SIGNALbutton to change

the volume of the end of cycle signal.

Pressthe button until you reach

the desiredvolume.

0 PREWASH

Prewash ton some models)

Prewashisan extra wash before

the main wash. Useit for heavily soiled

clothes or for clothes with a care label

that recommends prewashing before

washing. Be sureto add high-efficiency

detergent, or the proper wash additive

to the prewash dispenser.

NOTE:When selecting prewash,

it is recommended to use powder

detergent in the main wash (detergent)

compartment.

O

EXTRA Extra Rinse

Usean extra rinsewhen additional rinsing

is desiredto remove excessdirt and

detergent from soiledloads.

Delag Start

Youcan delaythe start ofa wash cycle

for 10-18 hours,dependingon the model.

Pressthe DELAYSTARTbutton to choose

the number of hoursyou want to delay

the start of the cycle,then presstheSTART

button.Themachine willcount down and

start automatically at the correcttime.

NOTE:Ifblouforgetto fully closethe door,

a remindersignalwill beep remindingyou

to do so.

NOTE:If you openthe door when the dela_l

iscounting down, the machinewill enter

thepausestate. Youmust closethe door

and pressSTARTagain in order to restart

thecountdown.

Lock

Youcan lock the controls to prevent any

selections from being made. Or you can

lock the controls after you have started

a cycle.

Children cannot accidentally start

the washer bbltouching pods with

this option selected.

Tolock the washer,pressand hold

the DELAYSTARTbutton for 3 seconds.

Tounlock the washer controls, press

and hold the DELAVSTARTbutton for

3 seconds.

The control lock icon on the display will

light up when it ison.

NOTE:ThePOWER button can still be

used when the machine is locked.

®

@

8

MV CYCLE (on some models)

Tosavea favoritecycle,setthedesired

settingsforwash cycle,soillevel,spinspeed

and washtemp settingsandholddown the

MVCYCLEbutton for3 seconds.A beepwill

soundto indicatethe cyclehasbeensaved.

To useyour custom cycle, pressthe

MVCYCLEbutton beforewashing a load.

Tochange the saved cycle, set the desired

settings and hold down the MVCYCLE

button for 3 seconds.

NOTE:When using MY CYCLE,wash

options cannot be modified after the

cgcle has been started.

NOTE:If btouchange wash options with

MYCYCLEbefore starting the chicle,the

MVCYCLElight will turn off and you will

be returned to the base cgcle.

BASKET CLEAN

BasketClean isa cycle that freshens up

the insideof your washer Thecycle uses

bleach and more water to refresh your

washer.Use BasketClean once every

month to reduceodor and residuebuildup

insidethe washer

Formore information on BasketClean,

referto the Careand Cleaningsection on

page 11.

ge.com

The Dispenser Drawer

Slowlyopen thedispenserdrawer bg pulling

it out untilit stops.

After addinglaundryproducts,slowlyclose

the dispenserdrawer.Closingthedrawertoo

quicklycouldresultin earlydispensingofthe

bleach,fabric softeneror detergent.

Youmay seewaterin thebleachand fabric

softenercompartmentsatthe endofthe cycle.

Thisiso resultof theflushing/siphoningaction

and ispart of thenormaloperationof the

washer.

ThePrewash Compartment (onsomemodels)

• Onlyusethe PrewashCompartmentif you

are selectingthe Prewashcyclefor heavily

soiledclothes.Addmeasureddetergentor

prewashadditiveto the backleft prewash

compartment ofthe dispenserdrawer.

• Detergentor prewashadditiveisflushed

from the dispenserin the prewashcycle

(ifselected).

NOTE:Liquiddetergentwill drain intothe

washerdrumasit is added.

• Detergentusagemay needto beadjusted

for water temperature,water hardness,size

and soillevelof the load.Avoidusingtoo

muchdetergent in yourwasher asit can

leadto oversudsingand detergent residue

beingleft onthe clothes.

owder

Insertin rearpositionforpowder

detergent

Liquid /

Icons

J

Insertinforwardpositionforliquid

detergent

The Detergent Compartment

• Highefficiency detergent is required

for this washer.Usethe detergent

manufacturer's recommendedamount.

Thedetergentselectioninsert must beplaced

inthe detergentcompartment ina specific

positionaccordingto what tgpe of detergent

gouare using.

• PowderDetergent - Placethe insert

QOQQ

inthe rear position.ThePowderIconsoooo....

mustline up on centerwhenthe insert

isinthe powderposition.

• Liquid Detergent - Placethe insertin

the forward position.TheLiquidIcons_"

mustline up on centerwhenthe insert

isinthe liquidposition.

Hovethe insert by pullingit up and replace

it byslidingit down betweeneitherthe rear

or front detergentcompartment moldedrails,

asdesired,for powderor liquid detergent.

• Addmeasureddetergentto the front left

detergent compartmentof the dispenser

drawer.

• Detergentisflushedfrom the dispenser

at the beginningofthe wash cycle. Either

powderedor liquid detergentcan beused.

• Detergentusagemay needto be adjusted

for water temperature,water hardness,

sizeand soillevelof the load.Avoidusing

too much detergentin yourwasher asit

can leadto oversudsingand detergent

residuebeingleft on the clothes.

• Usingmoredetergentthan the

recommendedquantity cancause

residuebuildupon your washer.

Onsomemodels,theLiquidBleach

Comportmentisinthe center.

Onsomemodels,theLiquidBleach

Compartmentisontheright.

The Liquid Bleach Compartment

IMPORTANT:Thebleachcompartment

position varies by model. Besureto identify

the correctcomportmentfor bleochbefore

using.

If desired,measureout the recommended

amount of liquid bleach,notto exceed

1/3cup (80ml)and pour into the center

compartment labeled"LIQUIDBLEACH"

markedwith this sgmbol /_,.

Donotexceedthemaximum fillline.Overfilling

concauseearly dispensingof thebleachwhich

couldresultin damagedclothes.

NOTE:Donotusepowderedbleachin the

dispenser.

About the washer features, gecom

Onsomemodels,theFabric

SoftenerCompartmentis

onthefight.

TheFabric Softener Compartment

IMPORTANT:Thefabric softener compartment

position varies by model.Besureto identify

the correct compartment for fabric softener

beforeusing.

Ifdesired,pour the recommendedamount

of liquidfabric softenerinto the compartment

labeled"FABRICSOFTENER."

Useonlg liquidfabric softenerin the dispensen

Dilutewith water to themaximum fillline.

Donot exceedthemaximum fillline.Overfilling

cancauseearlgdispensingof thefabricsoftener

which couldstainclothes.

NOTE:Donotpour fabric softenerdirectly

on thewash load.

Onsomemodels,theFabric

SoftenerCompartmentis

inthecenter

Loading and using the washer.

Afwoys follow fabric manufacturer's core tabef when laundering.

Sorting Wash Loads

Sort laundrg into loads that can be washed together.

Colors Soil Fabric Lint

Whites Heovg Delicotes Lint Producers

Lights Normal Easy Care Lint Collectors

Darks Light Sturdy Cottons

• Combine large and small items in o load. Load large items first. Large items should not be more than

half the total wash load.

• Washing single items is not recommended. This mag cause an out-of-balance load. Add one or two

similar items.

• Pillows and comforters should not be mixed with other items. This mag cause an out-of-balance load.

10

Loading the Washer

Wash drum mag be fullg loaded with Iooselg added To add items after washer has started, press

items. Do not wash fabrics containing flammable START/PAUSEand wait until the door is unlatched.

materials (waxes, cleaning fluids, etc.). The washer mag take up to BOseconds to unlock

the door after pressing START/PAUSEdepending

on the machine conditions. Do not trg to force open

the door when it is locked. After the door unlocks,

open gentlg. Add items, close the door and press

START/PAUSEto restart.

Cleaning the washer, gecom

Care and Cleaning

Exterior: Immediately wipe off any spills. Wipe with damp cloth. Do not hit surface with sharp objects.

Moving and Storage: Ask the service technician to remove water from drain pump and hoses.

Do not store the washer where it will be exposed to the weather When moving the washer,

the tub should be kept stationary by using the shipping bolts removed during installation.

See Installation Instructions in this book. If these parts are not available, they can be ordered

by visiting our Website at ge.com or by calling 800.GE.CARES.

Long Vacations: Be sure water supply is shut off at faucets. Drain all water from hoses if weather will be

below freezing.

Cleaning the interior

of the Washer

To clean the interior of the washer, select

the BasketClean feature on the control

panel. The cycle will use more water,

in addition to bleach, to refresh your

washer.

NOTE:Read the instructions below

completely before starting the

BasketCleancycle.

1. Remove any garments or objects from

the washer and ensure the washer

basket is empty.

2. Open the washer door and pour

one cup or 250 ml of liquid bleach

into the basket.

3. Close the door and select the

BasketClean cycle. Pushthe START

button.

4. When the BasketClean cycle is

working, you will see CLn on the

display. The cycle will complete in

about 90 minutes. Do not interrupt

the cycle.

5. After the cycle is complete, leave

the door open slightly for better

ventilation.

If for any reason the cycle needs to

be interrupted, the door will not open

immediately. Forcing open the door at

this stage may cause water to flood.

The door will open after the water is

drained to a level where it would not

flood the floor.

BasketClean may be interrupted

by pressing the START/PAUSE button

in between cycles. A power outage in

the house might also interrupt the cycle.

When the power supply is back, the

BasketClean cycle resumes where it had

stopped. When interrupted, be sure to run

a complete BasketClean cycle before

using the washer. If the POWER button

is pressed during BasketClean, the cycle

will be lost.

IMPORTANT:

II Run BasketClean with 1 Cup

(250 ml) of bleach once a month.

II After the completion of a BasketClean

cycle, the interior of your washer may

have a bleach smell.

II It is recommended to run a light color

load after the BasketClean cycle.

11

Cleaning the washer.

Cleaning the Pump Filter

Due to the nature of the front-load washer,

it is sometimes possible for small articles

to pass to the pump. The washer has a

filter to capture lost items so theg are not

dumped to the drain. To retrieve lost items,

clean out the pump filter.

Using a coin or flat screwdriver

in the notch on the door, open

the access door.

Place a shallow pan or dish under

the pump access door and towels

on the floor in front of the washer to

protect the floon It is normal to catch

about a cup of water when the filter

is removed.

3. Pull down the pour spout.

Pour

Pour __ ......

4. Turn the pump filter counterclockwise

and remove the filter. Open slowlg to

allow the water to drain.

5. Clean the debris from the filter.

6. Replace the filter and turn clockwise.

Tighten securelg.

7. Flip up the pour spout.

8. Close the access doon

12

Cleaning the Door Gasket

Open the washer door. Using both hands,

press down the door gasket. Remove ang

foreign objects if found trapped inside

the gasket. Make sure there is nothing

blocking the holes behind the gasket.

While holding down the door gasket,

inspect the interior gasket bg pulling it

down with gour fingers. Remove ang

foreign objects if found trapped inside

this gasket. Make sure there is nothing

blocking the holes behind the gasket.

When gou are finished cleaning

the door gasket, remove gour hands

and the gaskets will return

to the operating position.

ge.com

Dispenser Druwer Areu: Detergent and fabric softener mag build up

in the dispenser drawer. Residue should be removed once or twice a month.

• Remove the drawer bg first pulling it out until it stops. Then reach back into

the left rear corner of the drawer cavity and press down firml Uon the lock tab,

pulling out the drawer.

Lock tab is visible only after

drawer has been pulled out

Remove the inserts from the bleach and fabric softener compartments

and the detergent insert. Rinse the inserts and the drawer with hot water

to remove traces of accumulated laundr U products.

• To clean the drawer opening, use a small brush to clean the recess. Remove

all residue from the upper and lower parts of the recess.

• Return inserts to the proper compartments. Replace the dispenser drawee

13

Installation

Instructions

Washer

I If gou have ang questions, call 800.GE.CARES(800.432.2737) orvisitour Websiteat:ge.com I

In Canada, call 1.800.561.3344 or visitgeapplionces.co

I

BEFOREYOU BEGIN

Read these instructions completelg and carefullg.

• IMPORTANT - Savetheseinstructions

for local inspector's use.

• IMPORTANT - Observeall governing

codes and ordinances.

• Note to Installer - Be sure to leave these

instructions with the ConsumeE

• Note to Consumer - Keepthese instructions

for future reference.

• Skill level - Installation of this appliance requires

basic mechanical and electrical skills.

• Completion time - i-3 hours

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

FOR YOUR SAFETY:

-_WARNING

• This appliance must be properlu grounded and

installed as described in these Installation Instructions.

• Do not install or store appliance in an area where

it will be exposed to water/weather. See Location

of Your Washer section.

• NOTE: This appliance must be properlg

grounded, and electrical service to the washer

must conform with local codes and ordinances

and the latest edition of the National Electrical

Code, ANSI/NFPA 70.

TOOLS REQUIRED FOR

WASHER INSTALLATION

GII/4" nut driver

3/8" socket with ratchet

3/8" open-end wrench

GIAdjustable wrench or 7/16" socket with ratchet

GIAdjustable wrench or 9/16" open-end wrench

GIChannel-lock adjustable pliers

GICarpenter's level

PARTS SUPPLIED

G

CI Water Hoses (2)

E] Cable Tie

CI Hose Guide

STACK BRACKET KIT

A stack bracket kit is available at additional cost.

It can be ordered in the United States bg visiting

our website at ge.com or calling 800.GE.CARES.

Order kit #WE25X10018 or STACKITIWW.

14

Installation Instructions

LOCATION OF YOUR WASHER

Do Not Install the Washer:

1.In an area exposed to dripping water or outside

weather conditions. The ambient temperature should

never be below 60°F (15.6°C)for proper washer

operation.

2.In an area where it will come in contact with curtains

or drapes.

3.On carpet. The floor MUSTbe a hard surface with

a maximum slope of 1/2" per foot (1.27cm per

30 cm).To make sure the washer does not vibrate

or move, Uou mau have to reinforce the flooE

NOTE:If floor is in poor condition, use 3/4" impregnated

plywood sheet solidlu attached to existing floor covering.

IMPORTANT:

Minimum Installation Clearances

• When installed in alcove: Sides, Rear,

Top = O"(0 cm)

• When installed in closet: Sides,Rear,

Top = O"(0 cm), Front = 1" (2.54 cm)

• Closet door ventilation openings required:

2 louvers each 60 square in. (B87 cm2),located B"

(7.6cm) from top and bottom of door

ROUGH-IN DIMENSIONS

FRONT

27.0"

(68.6 cm)

20.4" (51.9 cm)

o o

2_2"

(5.6 cm)

40.6"*

(103.1 cm)

SIDE

30.6"

(77.7 cm)

(3.9 cm)

40.6"*

(103.1cm)

39.1"

(99.2 cm)

*NOTE: With pedestal, 52.6"

Stacked, 84"

15

Installation Instructions

UNPACKING THE WASHER

-AWARNING: Recycleor destroy the carton

and plastic bags after the washer isunpacked. Make

materials inaccessibleto children.Childrenmight use

them for play. Cartons coveredwith rugs,bedspreads

or plasticsheets can become airtight chambers causing

suffocation.

1. Cut and remove the top and bottom packaging straps.

2. Whileit isin the carton, carefully lay the washer on its

side.DONOTlag the washer on its front or back.

3. Turn down the bottom flaps-remove all basepackaging,

including the cardboard, styrofoam baseand styrofoam

tub support (insertedin center of base).

NOTE: If you are installing a pedestal, proceed to

the installation instructions that come with the pedestal.

4. Carefullyreturn the washer to an upright position and

remove the carton.

5. Carefullymove the washer to within 4 feet (122 cm)

of the final location.

6. Removethe following from the back sideof the washer:

4 bolts

4 plastic spacers (includingrubber grommets)

4 power cord retainers

NOTE:Failureto remove the shipping braces can cause

the washer to become severelyunbalanced.

Saveall bolts for future use.

NOTE:If you must transport the washer at a later date,

you must reinstall the shipping support hardware to prevent

shipping damage. Keepthe hardware in the plastic bag

provided.

Incase you misplace your shipping bolt, replacements

are available at additional cost. They can be ordered in

the United States by visiting our website at ge.com or

calling 800.GE.CARES.Order kit #WH49×10039.

16

Installation Instructions

ELECTRICAL REQUIREMENTS

Read these instructions completely

and carefully.

.A WARNING--TOREDUCETHERISKOF

FIRE,ELECTRICALSHOCKAND PERSONALINJURY:

• DO NOTUSEAN EXTENSIONCORDORANADAPTER

PLUGWITH THISAPPLIANCE.

Washer must be electrically grounded in accordance

with local codes and ordinances, or in the absence

of local codes, in accordance with the NATIONAL

ELECTRICALCODE,ANSI/NFPANO.70.

CIRCUIT- Individual,properly polarized and grounded

15-amp branch circuit fused with 15-amp time-delay fuse

or circuit breaker

POWERSUPPLY- 2-wire, with ground, 120-volt,

single-phase,60-Hz,Alternating Current.

OUTLETRECEPTACLE- Properly _ _

grounded 3-prong receptacleto be

located sothe power supply cord

is accessiblewhen the washer is

in an installed position. I ('i-_

GROUNDING REQUIREMENTS

-AWARNING: ,mproperconnectionofthe

equipment grounding conductor can result in a risk

ofelectrical shock.Checkwith a licensedelectrician

if you are in doubt asto whether the appliance is

properly grounded.

1. Thewasher MUSTbe grounded. Inthe event of

malfunction or breakdown, grounding will reduce

the riskof electricalshock bg providing a path of least

resistancefor electricalcurrent.

2.

Sinceyour washer isequipped with a power supply

cordhaving an equipment-grounding conductor and

a grounding plug,the plug MUSTbe plugged into an

appropriate, copper-wired receptacle that isproperly

installedand grounded in accordancewith all local

codesand ordinances or in the absence of localcodes,

with the National ElectricalCodes,ANSI/NFPA70 (latest

edition).If in doubt, calla licensedelectrician.DONOT

cut off or alter the grounding prong on the power supply

cord.In situationswhere a two-slot receptacleispresent,

itisthe owner's responsibilityto havea licensed

electricianreplaceit with a properly grounded

three-prong grounding-type receptacle.

WATER SUPPLY REQUIREMENTS

Hot and coldwater faucets MUSTbe installedwithin

42 inches (107 cm)of your washer's water inlet.Thefaucets

MUSTbe 3/4" (1.9cm) garden hose-type so inlethoses can

be connected. Water pressureMUSTbe between 10 and 120

pounds per square inch. Yourwater de )artment can advise

you of your water pressure.Thehot water temperature

should be set to deliverwater at 120°to 140°F(48°-60°C).

DRAIN REQUIREMENTS

1. Drain capable of eliminating 17gals (64.3L)

per minute.

2. A standpipe diameter of i 1/4" (3.18cm) minimum.

3. The standpipe height above the floor should be:

Minimum height: 24" (61cm)

Maximum height: 96" (244cm)

BACK

r-- I

I

[

96 in.

(244 cm)

Max.

NOTE:The drain hose attached to the washer can reach

a 58" (147cm) high standpipe. Fora higher standpipe,

contact an authorized parts distributon

17

Installation Instructions

INSTALLING THE WASHER

1. Runsome water from the hot and cold faucets to flush

the water linesand remove particles that might clog up

the water valve screens.

2. Removethe inlethosesfrom the plastic bag.

3. (gO°elbow end)Carefully

connect the inlet hose

marked HOTto the outside

"H" outlet of the water valve.

Tighten by hand,then tighten

another 2/3 turn with pliers.

Carefully connect the other

inlet hoseto the inside"C"

outlet of the water valve.

Tighten by hand;then tighten

another 2/3 turn with pliers.Donot crossthread

or over-tighten these connections.

4. Connectthe inlet hoseendsto the HOTand COLDwater

faucets tightly by hand,then tighten another 2/3 turn

with pliers.Turnthe water on and check for leaks.

5,

6,

Carefully move the washer to its final location. Gently rock

the washer into position.It isimportant notto damage

the rubber levelinglegswhen moving your washer

to its final location. Damaged legscan increasewasher

vibration. It man be helpfulto spray window cleaner on

the floor to help move your washer into its final position.

NOTE:To reducevibration, ensurethat all four rubber

levelinglegsare firmly touching the flooEPushand

pull on the back right and then back left of your washeE

NOTE:Do not usethe dispenser drawer or door to lift

the washe_

NOTE:If you are installing into a drain pan, you can use

a 24-inch long 2x4 to leverthe washer into place.

With the washer in its final position, place a level

on top of the washer _ ../

(if the washer is installed

under a counter, _" _ _ //

the washer should not

be able to rock). Adjust

the front leveling legs _-_

up or down to ensure

the washer is resting

solid. Turn the lock nuts on each leg up towards

the base of the washer and snug with a wrench.

NOTE:Keepthe leg extensionat a minimum to prevent

excessivevibration.Thefarther out the legs are extended,

the morethe washer will vibrate.

Ifthe floor isnot levelor isdamaged, you mag have

to extend the rear levelinglegs.

18

Installation Instructions

INSTALLING THE WASHER Icont.I

7. Attach U-shaped hose guide to the end of the drain

hose. Place the hose in a laundry tub or standpipe

and secure it with the cable tie provided in the

enclosure package.

NOTE:If the drain hose isplaced in a standpipe without

forming a Ushape, a siphoning action could occur There

must be an air gap around the drain hose.A snug hose

fit can alsocause a siphoning action.

CableTie7 Cable Tie 7

I

Cable Tie

8.

Plug the power cord into a grounded outlet.

NOTE:Check to be sure the power is off at a circuit

breaker/fuse box before plugging the power cord into

an outlet.

9. Turn on the power at a circuit breaker/fuse box.

10. Read the rest of this Owner's Manual. It contains

valuable and helpful information that will save you

time and moneg.

11. Before starting the washer, check to make sure:

CI Mainpower isturned on.

CIThewasher is plugged in.

CIThewater faucets are turned on.

CITheunit isleveland all four levelinglegsare firmly

on the floor

CITheshipping support hardware is removed

and saved.

CIThe drain hose isproperly tied up.

E]Thereare no leaks at the faucet, drain line

or washer

12. Run the washer through a complete cgcle.

Check for water leaks and proper operation.

13. If your washer does not operate, please review

the BeforeYouCallForServicesection before

calling for service.

14. Place these instructions in a location near the washer

for future reference.

REPLACEMENT PARTS

If replacement parts are needed for your washer,they

can be ordered in the United States by visiting our

Website at ge.com or by calling 800.GE.CARES.

19

Beforeyou call for service...

Troubleshooting Tips

Save time and money! Review the charts on the

following pages first and gou mag not need to call for

service.

Possible Cause What ToDo

Not spinning or agitating Drain hose is kinked or • Straighten drain hose and make surewasher isnot

improperlg connected sitting on it.

Household drain mag • Checkhousehold plumbing, Youmag needto call

be clogged a plumbeE

Drain hose siphoning; drain hose • Ensurethere isan air gap between hose and drain,

pushed too far down the drain

Washer pump filter mag • Havegour pump filter cleaned,

beclogged • Clean pump filter ifwasher isequipped with access door,

Load isout of balance • Redistributeclothesand run drain & spinor rinse&spin.

• Increaseloadsizeifwashing small load containing heavg

and lightitems.

Leaking water Door gasket is damaged • Check to see ifgasket is seated and not torn. Objects

left in pockets mag cause damage to the washer (nails,

screws, pens, pencils),

Door gasket not damaged • Water mag drip from the door when the door is opened.

This is a normal operation.

Check back left of washer • Ifthis area is wet, gou have oversudsing condition.

for water Use less detergent,

Fillhoses or drain hose is • Hake sure hose connections are tight at washer and

improperlg connected faucets and make sure end of drain hose is correctlg

inserted in and secured to drain facilitg.

Household drain meg • Check household plumbing. Youmag need to call

be clogged a plumber,

Dispenser clogged • Powder soap mag cause clogs inside the dispenser and

cause water to leak out the front of the dispenser, Remove

dispenser and clear asneeded.

Not draining Drain hose iskinked or • Straighten drain hose and make sure washer isnot

improperlg connected sitting on it.

Household drain mag • Checkhousehold plumbing. Youmag needto call

be clogged a plumber,

Drain hose siphoning; drain hose • Ensurethere isan air gap between hose and drain.

pushed too far down the drain

Washer pump filter mag • Have gour pump filter cleaned.

be clogged • Clean pump filter ifwasher isequipped with access door,

Bad odor inside Washer unused for a long time, • Leavethe door slightlg open for the water to air drg.

gour washer not using recommended • Runa BasketClean cgcle.

qualitg of HEdetergent

or used too much detergent • Inthe case of strong odor,gou mag need to run

the BosketCleon cgcle morethan once.

Not spinning Drain hoseiskinkedor • Straighten drain hose and make surewasher isnot

,mproperlg connected sitting on it.

Household drain mag • Checkhousehold plumbing. Youmag needto call

be clogged a plumber,

Drain hose siphoning; drain hose • Ensurethere isan air gap between hose and drain.

pushed too far down the drain

Washer pump filter mag • Havegout pump filter cleaned.

be clogged • Clean pump filter ifwasher isequipped with access door,

Load isout of balance • Redistributeclothesand run drain & spinor rinse&spin.

• Increaseloadsizeifwashing small load containing heavg

and lightitems.

Door isopen • Hakesure door isclosed.

20

La page charge ...

GE WCVH6800J1WW Owner's Manual and Installation Instructions

GE WCVH6800J1WW Owner's Manual and Installation Instructions

dans d''autres langues

Documents connexes

Autres documents