PAV-SIPA50SM-00 | 009-1658-01 | 180423
Copyright 2018 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
4 of 4
Important Safety Information - Read First
Before installing, confi guring, and operating Savant equipment and
other vendor equipment, Savant recommends that each dealer, inte-
grator, installer, etc. access and read all the required technical docu-
mentation. Savant technical documentation can be located by visiting
Savant.com. Vendor documentation is supplied with the equipment.
Read and understand all safety instructions, cautions, and warnings in
this document and the labels on the equipment.
Safety Statements
Follow all of the safety instructions listed below and apply where
applicable. Additional safety information will be included where appli-
cable.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with
the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat regis-
ters, stoves, or other apparatus (including amplifi ers) that produce
heat.
9. Do not defeat the safety purpose of the polarized or ground-
ing-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided
for your safety. If the provided plug does not fi t into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particu-
larly at plugs, convenience receptacles, and the point where they
exit from the apparatus.
11. Only use attachments/accessories specifi ed by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specifi ed by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualifi ed service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
15. To completely disconnect this equipment from the AC mains,
disconnect the power supply cord plug from the AC receptacle.
16. Use the included power cord with the grounding prong intact to
insure proper grounding of the device.
Informations importantes sur la sécurité - Lire
d’abord
Avant d’installer, de confi gurer et d’utiliser des équipements Savant
et d’autres équipements fournisseurs, Savant recommande à chaque
revendeur, intégrateur, installateur, etc. d’accéder et de lire toute la
documentation technique requise. La documentation technique de
Savant peut être localisée en visitant Savant.com. La documentation
du fournisseur est fournie avec l’équipement.
Lisez et comprenez toutes les consignes de sécurité, les mises en
garde et les avertissements dans ce document et les étiquettes sur
l’équipement.
Déclarations de sécurité
Suivez toutes les consignes de sécurité ci-dessous et appliquez le cas
échéant. Des informations de sécurité supplémentaires seront incluses,
le cas échéant.
1. Lisez ces instructions.
2. Gardez ces instructions.
3. Suivez tous les avertissements.
4. Suivez toutes les instructions.
5. Ne pas utiliser cet appareil près de l'eau.
6. Nettoyer uniquement avec un chi on sec.
7. Ne bloquez aucune bouche d'aération. Installez conformément aux
instructions du fabricant.
8. Ne pas installer à proximité de sources de chaleur telles que des ra-
diateurs, des registres de chaleur, des poêles ou d'autres appareils
(y compris les amplifi cateurs) qui produisent de la chaleur.
9. Ne débrouillez pas le but de sécurité de la fi che polarisée ou de
mise à la terre. Une fi che polarisée comporte deux pales dont une
plus large que l'autre. Une fi che de type à la terre comporte deux
lames et une troisième broche de mise à la terre. La lame large
ou la troisième broche est fournie pour votre sécurité. Si la fi che
fournie ne rentre pas dans votre prise, consultez un électricien pour
le remplacement de la sortie obsolète.
10. Protégez le cordon d'alimentation avant d'être piétiné ou pincé en
particulier sur les bouchons, les prises de courant et le point où ils
sortent de l'appareil.
11. Utilisez uniquement les pièces jointes / accessoires spécifi ées par
le fabricant.
12. Utilisez uniquement le chariot, le support, le trépied, le support ou
la table spécifi és par le fabricant ou vendus avec l'appareil. Lor-
squ'un chariot est utilisé, faites preuve de prudence lorsque vous
déplacez la combinaison panier / appareil pour éviter les blessures
par dépassement.
13. Débranchez cet appareil pendant les orages ou lorsqu'il n'est pas
utilisé pendant de longues périodes.
14. Renvoyez tous les services au personnel qualifi é. Un entretien
est nécessaire lorsque l'appareil a été endommagé de quelque
façon que ce soit, comme le cordon d'alimentation ou la fi che est
endommagé, le liquide a été renversé ou les objets sont tombés
dans l'appareil, l'appareil a été exposé à la pluie ou à l'humidité, ne
fonctionne pas normalement, Ou a été abandonné.
15. Pour débrancher complètement cet équipement du secteur,
débranchez la fi che du cordon d'alimentation de la prise secteur.
16. Utilisez le cordon d’alimentation inclus avec la broche de mise à la
terre intacte pour assurer une mise à la terre correcte de l’appareil.
Printed in China
Part # HDH6C001010
PAV-SIPA50SM-00 | 009-1658-01 | 180423
Copyright 2018 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
1 of 4
Box Contents
(1) Savant IP Audio 50 (PAV-SIPA50SM)
(2) Enclosure Bracket (071-1103-xx)
(1) 2U Rack Bracket (071-1102-xx)
(1) Power Cord (064-0079-xx)
(4) #10x½ Screw (039-0405-xx)
(4) Push Rivet (039-0406-xx)
(6) M4 Screw (039-0403-xx)
(4) 4-pin Speaker Connector (028-0702-xx)
(2) 4-pin IR Connector (028-0703-xx)
(4) Rubber Feet (074-0655-xx)
(4) M3 Feet Screw (039-0407-xx)
(1) Quick Reference Guide (this document)
Specifi cations
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 80% Relative Humidity (non-condensing)
Maximum BTU 750 BTU/HR
Power
Input Power 100/240V AC (50/60 Hz) 5.7A
Maximum Power 225W
Operating Parameters
Rated Power
(Speaker Output)
50 WPC at 8 ohms (THD+N < 0.1%)
70 WPC at 8 ohms (THD+N < 1.0%
Frequency
Response
20 Hz - 20 kHz +/- 0.5 dB, speaker output
Signal-to-Noise
Ratio (SNR)
>95 dB, speaker output
Supported Digi-
tal Input Formats
44.1 kHz / 48 kHz / 96 kHz at 16-bit / 20-bit /
24-bit resolution
Networking
Supported
Standard
IEEE 802.1 AVB/TSN switches
IEEE 802.3 Ethernet
Regulatory
Safety and
Emissions
FCC Part 15B CE Mark C-Tick UL
RoHS Compliant
Minimum Support Requirements
Software
Release
da Vinci 8.8
Music Streaming
The Savant IP Audio 50 has a built-in single stream of Savant Music
for easy access to popular music streaming services. (Streaming
service fees may apply.)
Savant® IP Audio 50 with Savant Music 2.0 (PAV-SIPA50SM)
Quick Reference Guide
Dimensions
Height Width Depth Weight
3.03 in
(77 mm)
12.00 in
(305 mm)
14.17 in
(360 mm)
10.6 lb
(4.81kg)
Rack Space: 2U
Front Panel
G
FED
C
BA
A
Power LED
Green: System has power and is operating
normally.
Red: System is in standby mode and most of the
controller circuitry is powered down.
O : System is not receiving power.
B
Status LED
Green Blinking: Embedded system is ready, but
no communication has been established with the
host.
Green: Host has established communications
with the embedded system.
Red Blinking: Embedded fi rmware is running, but
has not received a DHCP IP Address.
Red: Host has determined the fi rmware needs to
be updated, but a problem occurred during the
process that will initiate a reset.
Amber Blinking: Embedded system has a valid
link local IP Address and is connecting to the
host.
Amber: Host is updating the embedded
fi rmware.
O : Embedded processor is resetting, or is
powered up, and is booting the embedded
fi rmware.
Hardware Failure: If a hardware failure occurs,
the status LED indication will be interrupted
every three seconds with a solid red indication.
For example, if the LED is blinking green when a
hardware failure occurs, the LED will
alternate between blinking green and solid red at
three-second intervals.
C
RS232 LED
Green: RS-232 serial port activity.
O : No RS-232 serial port activity.
D
IR LED
Green: IR port signal activity.
O : No IR port activity.
E
On/O
Button
On: Fully enables all internal power rails and
processor.
O : Disables most internal power rails and
processor, but not internal AC/DC power supply.
Hold On/O button for about 5 seconds to place
into standby mode. The Power LED turns red.
Hold On/O button for about 1 second to take
system out of standby mode. The I/O power
switch on the back of unit must be On (I) to
enable this function. To turn the power o for the
entire system, press the I/O power switch on the
rear panel to O [O].
F
Reset Button
Resets the network.
Hold Reset Button for 5 seconds while powered
Onto clear network settings. Status LED will rap-
idly blink red when reset is complete.
G
Zone
Protection
Red: Protection mode has been enabled to pro-
tect a zone/channel; typically indicates thermal
protection, clipping or over current.
O : Zone is o and protection mode has not
been enabled.