Chamberlain C610C Mode d'emploi

Catégorie
Porte de garage
Taper
Mode d'emploi
TO WATCH VIDEOS GO TO:
tinyurl.com/lgh5x3h
Contents
Owner’s Manual
C610C
Chain Drive
Garage Door Opener
FOR RESIDENTIAL USE ONLY
PRE-PROGRAMMED REMOTE CONTROL
INCLUDED
www.chamberlain.com
www.mychamberlain.com
Please read this manual and the enclosed safety materials carefully!
Fasten the manual near the garage door after installation.
The door WILL NOT CLOSE unless the Protector System
®
is connected
and properly aligned.
Periodic checks of the garage door opener are required to ensure
safe operation.
The model number label is located on the front panel of your garage
door opener.
This garage door opener is compatible with MyQ® and
Security+b2.0® accessories.
DO NOT install on a one-piece door if using devices or features
providing unattended close. Unattended devices and features are
to be used ONLY with sectional doors.
Garage Opener
Preparation ...................................... 2-5
Assembly .......................................6-10
Installation ..................................11-28
Install the Door Control ............21-22
Install the Protector System® ....23-26
Connect Power .........................27-28
Adjustments .................................29-31
Operation .....................................32-36
Features .......................................33
Using your Garage Door Opener .....34
Motion Detecting Control Panel .....34
Remote Control and
Keyless Entry ................................35
Homelink® ...................................36
To Erase the Memory .....................36
To Open the Door Manually ...........37
Maintenance .....................................38
Troubleshooting ........................... 39-40
Accessories ........................................ 41
Warranty ........................................... 42
Repair Parts .................................43-44
2
Safety Symbol and Signal Word Review
Thisgarage door opener has been designed and tested to offer safe service provided it is installed,
operated,maintained and tested in strictaccordance with the instructions and warningscontained in
thismanual.
Mechanical
Electrical
When you see these Safety Symbolsand Signal
Words on the following pages,they will alertyou to
the possibility of serious injury or death ifyou do
not complywith the warningsthat accompany
them. The hazard may come fromsomething
mechanical or fromelectric shock.Read the
warningscarefully.
When you see this Signal Word on the following
pages, it will alertyou to the possibility of damage
to your garage door and/or the garage door
opener ifyou do notcomplywith the cautionary
statementsthat accompanyit.Read them carefully.
WARNING: Thisproduct can expose you to chemicalsincluding lead, which are known to the
State of California to cause cancer or birth defects or other reproductive harm.For more
information go to www.P65Warnings.ca.gov
Unattended Operation
The Timer-to-Close (TTC) feature, the MyQ
®
Smartphone Control app,and MyQ
®
Garage Door and
Gate Monitor are examples of unattended close and are to be used ONLY with sectional doors. Any
device or feature thatallowsthe door to close withoutbeing in the line of sightofthe door is considered
unattended close. The Timer-to-Close (TTC) feature, the MyQ
®
Smartphone Control,and any other
MyQ
®
devicesare to be used ONLY with sectional doors.
Check the Door
To preventpossible SERIOUSINJURYor DEATH:
l ALWAYS call a trained door systemstechnician if garage door binds, sticks, or is out of balance.
An unbalanced garage door mayNOT reverse when required.
l NEVER tryto loosen,move or adjust garage door,door springs, cables, pulleys,brackets or
their hardware, ALLof which are under EXTREME tension.
l Disable ALLlocks and remove ALLropes connected to garage door BEFORE installation and
operating garage door opener to avoid entanglement.
l DO NOT install on a one-piece door if using devices or features providing unattended close.
Unattended devicesand featuresare to be used ONLY with sectional doors.
To preventdamage to garage door and opener:
l ALWAYS disable locks BEFORE installing and operating the opener.
l ONLY operate garage door opener at 120V,60Hzto avoid malfunction and damage.
Before you begin:
1. Disable locks and remove anyropes connected to the garage door.
2. Lift the door halfway up. Release the door. If balanced,it should stay in
place, supported entirelybyitssprings.
3. Raise and lower the door to checkfor binding or sticking. If your door
binds, sticks, or is outofbalance,call a trained door systems
technician.
4. Checkthe seal on the bottomofthe door. Any gap between the floor
and the bottomofthe door must not exceed 1/4 inch (6 mm).
Otherwise, the safetyreversal system may notwork properly.
5. The opener should be installed above the center of the door. If there is
a torsion spring or center bearing plate in the way of the header
bracket, itmay be installed within 4feet(1.2 m) to the leftor rightofthe
door center.See page 12.
Torsion
Spring
Extension
Spring
OR
Preparation
3
Additional Items You May Need:
Survey your garage area to see if you will need anyofthe following items:
n (2) 2X4 PIECES OFWOOD
Maybe used to fasten the header bracketto the structural supports. Also used to position the
garage door opener during installation and for testing the safety reversing sensors.
n SUPPORT BRACKETANDFASTENING HARDWARE
Must be used if you have a finished ceiling in your garage.
n EXTENSIONBRACKETS (MODEL 041A5281-1) OR WOOD BLOCKS
Depending upon garage construction,extension brackets or wood blocksmay be needed to
install the safetyreversing sensor.
n FASTENING HARDWARE
Alternate floor mounting ofthe safetyreversing sensor will require hardware notprovided.
n DOOR REINFORCEMENT
Required if you have a lightweightsteel, aluminum, fiberglass or glass panel door.
n RAIL EXTENSION KIT
Required if your garage door is more than 7 feet(2.13 m) high.
Tools Needed
3/16
7/16
1/2
5/32
5/16
5/8
9/16
1/4
7/16
Preparation
4
Carton Inventory
Save the carton and packing material until the installation and adjustmentis complete. Instructions for
the accessories will be attached to the accessoryand are notincluded in this manual. The images
throughoutthis manual are for reference onlyand your product maylook different.
Model Power Door Control Remote Control Wireless Keypad
C610C PlusLiftPower System™ Motion Detecting 3-button (2)
ü
A. Header bracket
B. Pulley
C. Door bracket
D. Curved door arm
E. Straight door arm (Packaged inside front rail section)
F. Trolley
NOTE: Be sure to assemble the trolley before sliding onto rail.
G. Emergencyrelease rope and handle
H. Rail (1 front and 4 center sections)
I. Hanging brackets (2) (Packaged inside the front rail section)
J. Garage door opener (motor unit)
K. Chain spreader with screws
L. “U bracket
M. Chain and cable
N. Door control
O. Remote control
P. The Protector System
®
Safety reversing sensors with 2 conductor white and white/blackwire attached: Sending
Sensor (1),Receiving Sensor (1), and SafetySensor Brackets (2)
NOTSHOWN
WirelessKeypad
White and red/white wire
Owner'smanual
Hardware
N
A
B
C
H
K
J
O
I
D
E
F
G
L
M
P
Preparation
5
Hardware
ASSEMBLY INSTALLATION
DOOR CONTROL
Insulated Staples
(Not Shown)
Bolt
1/4"-20x1-3/4"
Lock Nut
1/4"-20
Bolt
Nut 3/8" Lock Washer 3/8"
Master Link (2)
Threaded
Shaft
Clevis Pin 5/16"x1-1/2"
Ring
Fastener (3)
Hex Bolt 5/16"-18x7/8" (4)
Lock Washer
5/16"-18 (5)
Nut
5/16"-18 (6)
Self-Threading Screw
1/4"-14x5/8" (2)
Clevis Pin 5/16"x1" Clevis Pin 5/16"x1-1/4"
Carriage Bolt
1/4"-20x1/2" (2)
Wing Nut
1/4"-20 (2)
Lag Screw 5/16"-9x1-5/8" (4)
Screw 6ABx1" (2)
Drywall Anchors (2)
Screw 6-32x1" (2)
Preparation
6
Assembly
STEP 1 Assemble the rail and install the trolley
To preventINJURY from pinching,keep handsand fingersaway fromthe joints while assembling the
rail.
To avoidinstallationdifficulties,donot run the garage dooropener until instructedtodo so.
The front rail has a cut out “window at the door end. The rail tab MUST be on top ofthe rail when
assembled.
1. Remove the straight door arm and hanging bracketpackaged inside the front rail and set
aside for Installation Step 5 and 9.NOTE: To prevent INJURY while unpacking the rail
carefully remove the straight door arm stored within the rail section.
2. Align the rail sections on a flatsurface as shown and slide the tapered endsinto the larger
ones. Tabsalong the side will lockinto place.
3. Place the motor uniton packing material to protect the cover,and rest the back end of the rail
on top.For convenience,puta supportunder the front end of the rail.
4. Asa temporary stop, insert a screwdriver into the hole in the second rail section from the motor
unit,asshown.
5. Checkto be sure there are 4 plastic wear pads inside the inner trolley.Ifthey became loose
during shipping, check all packing material. Snap them backinto position as shown.
6. Slide the trolley assembly toward the screwdriver asshown.
7. Slide the rail onto the U bracket,until it reaches all the stopson the top and sides of the “U”
bracket.
Wear Pads
Front Rail Section
(TO DOOR)
“U” Bracket
(TO MOTOR UNIT)
Trolley
Rail Tab
On Top
Slide to stops
on top and sides
of “U” bracket
Screwdriver
7
Assembly
STEP 2 Fasten the rail to the motor unit
To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the
top of the opener.
1. Inserta 1/4"-20 x 1-3/4" boltinto the cover protection bolthole on the back end of the rail as
shown.Tighten securely with a 1/4"-20 locknut. DO NOT overtighten.
2. Remove the boltand locknutfrom the top ofthe motor unit.
3. Use the carton to supportthe front end of the rail.
4. Place the U bracket,flat side down onto the motor unit and align the bracket holes with the
bolt holes.
5. Fasten the “U” bracketwith the previously removed boltand lock nut;DO NOTuse any power
tools. The use ofpower tools maypermanentlydamage the garage door opener.
6. Attach chain spreader to the motor unitwith two screws.
8
Assembly
STEP 3 Install the idler pulley
1. Lay the chain/cable beside the rail,asshown. Grasp the end of the cable and pass
approximately 12" (30 cm) of cable through the window. Allow it to hang until Assembly
Step4.
2. Remove the tape fromthe idler pulley. The inside center should be pre-greased. If dry,
regrease to ensure proper operation.
3. Place the idler pulleyinto the window as shown.
4. Insertthe idler boltfrom the top through the rail and pulley.Tighten with a 3/8" lockwasher
and nutunderneath the rail until the lock washer is compressed.
5. Rotate the pulley to be sure itspins freely.
6. Locate the rail tab.The rail tab is near the idler pulley on the front rail section.Use a flathead
screwdriver and liftthe rail tab until the tab is vertical (90º).
Rail
Idler Pulley
Grease Inside
Pulley
Bolt
Chain/cable
Lock Washer
Nut
Bolt
Nut 3/8" Lock Washer 3/8"
HARDWARE
Rail Tab
9
Assembly
STEP 4 Install the chain
To avoid possible SERIOUS INJURY to finger frommoving garage door opener:
l ALWAYS keep hand clear of sprocketwhile operating opener.
l Securelyattach sprocket cover BEFORE operating.
1. Pull the cable around the idler pulley and toward the trolley.
2. Connect the cable to the retaining sloton the trolley, as shown. (Figure 1)
a. Push pinsofmaster link bar through cable link and trolley slot.
b. Push master linkcap over pins and pastpin notches.
c. Slide the closed end of the clip-on spring over one ofthe pins. Push the open end of
the clip-on spring onto the other pin.
3. With the trolley against the screwdriver, dispense the remainder of the cable/chain along the
rail toward the motor unitaround the sprocket and continuing to the trolley assembly.The
sprocket teeth mustengage the chain. (Figure 2)
4. Checkto make sure the chain is not twisted, then connectitto the threaded shaftwith the
remaining master link.
5. Thread the inner nut and lock washer onto the trolleythreaded shaft.
6. Insertthe trolley threaded shaft through the hole in the trolley.Be sure the chain is not twisted.
(Figure 3)
7. Looselythread the outer nutonto the trolley threaded shaft.
8. Remove the screwdriver.
10
Assembly
STEP 5 Tighten the chain
1. Spin the inner nutand lockwasher down the trolley threaded shaft,away from the trolley.
2. To tighten the chain, turn the outer nut in the direction shown.
3. When the chain is approximately1/4" (6 mm) above the base of the rail at it's midpoint,
retighten the inner nut to secure the adjustment.
Sprocketnoise can resultif the chain is too loose. When installation is complete, you may notice some
chain droop with the door closed.This is normal. Ifthe chain returns to the position shown when the
door is open,do notre-adjustthe chain.
NOTE: During future maintenance, ALWAYS pull the emergency release handle to disconnectthe
trolley before adjusting the chain.
You have now finished assembling your garage door opener.Please read the following warnings
before proceeding to the installation section.
Outer
Nut
Lock
Washer
Trolley
Threaded
Shaft
Inner Nut
To Tighten
Inner Nut
To Tighten
Outer Nut
Mid length of RailBase of Rail
Chain
1/4" (6 mm)
11
Installation
IMPORTANT INSTALLATION INSTRUCTIONS
To reduce the risk of SEVERE INJURY or DEATH:
1. READAND FOLLOW ALL INSTALLATION WARNINGS ANDINSTRUCTIONS.
2. Install garage door opener ONLY on properly balanced and lubricated garage door.An
improperlybalanced door may NOT reverse when required and could result in SEVERE
INJURY or DEATH.
3. ALL repairsto cables, spring assembliesand other hardware MUST be made by a trained door
systems technician BEFORE installing opener.
4. Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing opener
to avoid entanglement.
5. Install garage door opener 7 feet(2.13 m) or more above floor.
6. Mountthe emergencyrelease within reach, butat least 6 feet (1.83 m) above the floor and
avoiding contact with vehicles to avoid accidental release.
7. NEVER connect garage door opener to power source until instructed to do so.
8. NEVER wear watches, ringsor loose clothing while installing or servicing opener. Theycould
be caught in garage door or opener mechanisms.
9. Install wall-mounted garage door control:
l within sight ofthe garage door.
l out of reach of small children ata minimum heightof 5feet (1.5m) above floors,landings,
steps or any other adjacent walking surface.
l away from ALL moving parts of the door.
10. Place entrapmentwarning label on wall nextto garage door control.
11. Place manual release/safety reverse test label in plain view on inside ofgarage door.
12. Upon completion of installation,test safety reversal system.Door MUST reverse on contactwith a
1-1/2" (3.8cm) high object (or a 2x4 laid flat) on the floor.
13. To avoid SERIOUS PERSONAL INJURY or DEATHfrom electrocution, disconnect ALL electric
power BEFORE performing ANY service or maintenance.
14. DO NOT install on a one-piece door if using devices or features providing unattended close.
Unattended devicesand featuresare to be used ONLY with sectional doors.
12
Installation
STEP 1 Determine the header bracket location
To preventpossible SERIOUS INJURY or DEATH:
l Header bracketMUSTbe RIGIDLY fastened to structural supporton header wall or ceiling,
otherwise garage door mightNOT reverse when required.DO NOT install header bracketover
drywall.
l Concrete anchors MUST be used if mounting header bracketor 2x4 into masonry.
l NEVER tryto loosen,move or adjust garage door,springs, cables, pulleys,brackets,or their
hardware,ALL of which are under EXTREME tension.
l ALWAYS call a trained door systemstechnician if garage door binds, sticks, or is out of balance.
An unbalanced garage door mightNOT reverse when required.
Installation procedures varyaccording to garage door types.Followthe instructions which applyto your
door.
1. Close the door and mark the inside vertical centerline of the garage door.
2. Extend the line onto the header wall above the door.You can fasten the header bracket within
4 feet(1.22 m) of the leftor right ofthe door center onlyifa torsion spring or center bearing
plate is in the way; or you can attach it to the ceiling (see page 13) when clearance is minimal.
(It may be mounted on the wall upside down if necessary, to gain approximately 1/2" (1 cm). If
you need to install the header bracketon a 2x4 (on wall or ceiling), use lag screws (not
provided) to securelyfasten the 2x4 to structural supportsasshown here and on page 13.
3. Open your door to the highestpoint oftravel asshown.Draw an intersecting horizontal line on
the header wall 2" (5 cm) above the high point:
l 2" (5 cm) above the high pointfor sectional door and one-piece door with track.
l 8" (20 cm) above the high point for one-piece door without track.
Thisheight will provide travel clearance for the top edge of the door.NOTE: If the total number of inches
exceeds the height available in your garage, use the maximum height possible, or refer to page 13 for
ceiling installation.
Header Wall
Vertical Centerline of Garage Door
2x4
Structural
Supports
Level
(Optional)
Unfinished
Ceiling
2x4
OPTIONAL CEILING MOUNT
FOR HEADER BRACKET
Sectional door with curved track
Header Wall
Track
2" (5 cm)
Highest
Point of
Travel
Door
One-piece door with horizontal track
Header Wall
Track
2" (5 cm)
Highest
Point of
Travel
Door
One-piece door without track:
jamb hardware
Header Wall
8" (20 cm)
Highest
Point of
Travel
Door
Jamb
Hardware
One-piece door without track:
pivot hardware
Header Wall
8" (20 cm)
Highest
Point of
Travel
Door
Pivot
13
Installation
STEP 2 Install the header bracket
You can attach the header bracketeither to the wall above the garage door,or to the ceiling.Follow the
instructionswhich will work bestfor your particular requirements.Do not installthe header bracket
overdrywall.If installing into masonry, use concrete anchors (not provided).
OPTION A WALL INSTALLATION
1. Center the bracket on the vertical centerline with the bottomedge of the bracketon the
horizontal line asshown (with the arrow pointing toward the ceiling).
2. Mark the vertical set of bracketholes.Drill 3/16" pilot holesand fasten the bracketsecurely to a
structural supportwith the hardware provided.
OPTION B CEILING INSTALLATION
1. Extend the vertical centerline onto the ceiling as shown.
2. Center the bracket on the vertical mark, no more than 6" (15 cm) fromthe wall.Make sure the
arrowispointing away fromthe wall.The bracketcan be mounted flush against the ceiling
when clearance is minimal.
3. Mark the side holes. Drill 3/16" pilotholes and fasten bracketsecurely to a structural support
with the hardware provided.
UP
Wall Mounting
Holes
WALL INSTALLATION
CEILING INSTALLATION
Optional Mounting
Holes
Vertical
Centerline of
Garage Door
Header Wall
Header
Bracket
2x4
Structural
Support
Door
Spring
Garage Door
Highest Point
of Garage
Door Travel
Horizontal
Line
Lag
Screw
UP
Header Wall
Ceiling Mounting
Holes
Finished Ceiling
Vertical
Centerline of
Garage Door
Header
Bracket
6" (15 cm)
Maximum
Door Spring
Garage Door
Lag Screw
14
Installation
STEP 3 Attach the rail to the header bracket
1. Position the opener on the garage floor below the header bracket.Use packing material asa
protective base.
NOTE: If the door spring is in the way, you will need help. Have someone hold the opener
securely on a temporary support to allow the rail to clear the spring.
2. Position the rail bracketagainstthe header bracket.
3. Align the bracketholes and join with a clevis pin as shown.
4. Inserta ring fastener to secure.
HARDWARE
Clevis Pin
5/16"x1-1/2"
Ring Fastener
Clevis Pin
Ring Fastener
STEP 4 Position the garage door opener
To preventdamage to garage door,rest garage door opener rail on 2x4 placed on top section of
door.
1. Remove the packing material and liftthe garage door opener onto a ladder.
2. Fully open the door and place a 2x4 (laid flat) under the rail.For one-piece doors without
tracks, lay the 2x4 on it's side.
NOTE: A 2x4 is ideal for setting the distance between the rail and the door. If the ladder is not tall
enough you will need help at this point. If the door hits the trolley when it is raised, pull the trolley
release arm down to disconnect the inner and outer trolley. Slide the outer trolley toward the garage
door opener. The trolley can remain disconnected until instructed.
Connected Disconnected
One-piece door
without tracks
2x4 2x4
All other
door types
15
Installation
STEP 5 Hang the garage door opener
To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to
structural supportsofthe garage. Concrete anchorsMUSTbe used if installing ANY bracketsinto
masonry.
Hanging the garage door opener will vary depending on your garage. Below are three example
installations.Your installation may be different.For ALL installationsthe garage door opener MUSTbe
connected to structural supports. The instructions illustrate one of the examples below.
1. On finished ceilings, use the lag screwsto attach a support bracket(notprovided) to the
structural supportsbefore installing the garage door opener.
2. Make sure the garage door opener is aligned with the header bracket. Measure the distance
fromeach side of the garage door opener to the supportbracket.
3. Cut both pieces of the hanging bracketto required lengths.
4. Attach the end of each hanging bracket to the supportbracket with appropriate hardware (not
provided).
5. Attach the garage door opener to the hanging brackets with the hexbolts,lock washers,and
nuts.
6. Remove the 2x4 and manuallyclose the door. If the door hits the rail,raise the header bracket.
Finished Ceiling
Lag Screw
1
2
3
Not
Provided
Not Provided
Not Provided
Hex Bolt
Nut
Lock
Washer
4 5
6
Lag Screw
Finished Ceiling
EXAMPLES
Unfinished Ceiling
HARDWARE
Hex Bolt
5/16"- 18x7/8"
Nut
5/16"-18
Lock Washer
5/16"-18
Lag Screw
5/16"-9x1-5/8"
16
Installation
STEP 6 Install the light bulbs
To preventpossible OVERHEATING of the end panel or lightsocket:
l Use ONLY A19 incandescent (100W maximum) or compactfluorescent(26W maximum) light
bulbs.
l DO NOT use incandescent bulbslarger than 100W.
l DO NOT use compact fluorescent lightbulbs larger than 26W (100W equivalent).
l DO NOT use halogen bulbs.
l DO NOT use short neckor specialty lightbulbs.
1. Pull on the top sides of the lightlens and rotate the lightlens down.
2. Insertan A19 incandescent (100Wmaximum) or compactfluorescent (26W,100W
equivalent) lightbulb into the light socket.
3. Rotate the lensup to close.
NOTE: Do notuse halogen, short neck, or specialty light bulbs as these may overheat the end panel or
light socket. Do not use LED bulbs as they may reduce the range or performance of your remote
controls.
or or
STEP 7 Attach the emergency release rope and handle
To preventpossible SERIOUS INJURY or DEATHfrom a falling garage door:
l If possible,use emergency release handle to disengage trolley ONLY when garage door is
CLOSED. Weakor broken springsor unbalanced door could result in an open door falling
rapidly and/or unexpectedly.
l NEVER use emergencyrelease handle unless garage doorwayisclear of persons and
obstructions.
l NEVER use handle to pull door open or closed. If rope knot becomesuntied,you could fall.
1. Insertone end ofthe emergencyrelease rope through the handle. Make sure that “NOTICE”
is rightside up.Secure with an overhand knot at least1" (2.5 cm) fromthe end of the rope to
prevent slipping.
2. Insertthe other end of the emergencyrelease rope through the hole in the trolley release arm.
Mount the emergency release within reach, but at least 6 feet (1.83 m) above floor, avoiding
contactwith vehicles to prevent accidental release and secure with an overhand knot.
NOTE: If it is necessary to cut the emergency release rope, seal the cut end with a match or lighter to
prevent unraveling. Ensure the emergency release rope and handle are above the top of all vehicles to
avoid entanglement.
17
Installation
STEP 8 Install the door bracket
Fiberglass,aluminumor lightweightsteel garage doorsWILLREQUIRE reinforcementBEFORE
installation of door bracket. Contactthe garage door manufacturer or installing dealer for opener
reinforcementinstructions or reinforcement kit.Failure to reinforce the top section asrequired
according to the door manufacturer may void the door warranty.
A horizontal and vertical reinforcementisneeded for lightweight garage doors(fiberglass,aluminum,
steel, doorswith glass panel,etc.) (notprovided). A horizontal reinforcementbrace should be long
enough to be secured to two or three vertical supports. A vertical reinforcementbrace should cover the
heightofthe top panel. Contactthe garage door manufacturer or installing dealer for opener
reinforcementinstructions or reinforcement kit.
NOTE: Many door reinforcement kits provide for direct attachment of the clevis pin and door arm. In this
case you will not need the door bracket; proceed to the next step.
OPTION A SECTIONAL DOORS
1. Center the door bracketon the previously marked vertical centerline used for the header
bracketinstallation.Note correctUP placement,asstamped inside the bracket.
2. Position the top edge of the bracket2"-4" (5-10cm) belowthe top edge of the door, OR
directlybelow any structural supportacrossthe top of the door.
3. Mark,drill holes and install as follows,depending on your door’s construction.
Metal or light weight doors usinga verticalangle iron brace between the doorpanelsupport and
the doorbracket:
l Drill 3/16" fastening holes. Secure the door bracket using the two 1/4"-14x5/8" self-threading
screws. (Figure1)
l Alternately,use two 5/16"-18x2" bolts, lock washers and nuts (not provided).(Figure2)
Metal, insulatedorlight weight factory reinforced doors:
l Drill 3/16" fastening holes. Secure the door bracket using the self-threading screws. (Figure3)
Wooddoors:
l Use top and bottom or side to side door bracketholes.Drill 5/16" holesthrough the door and
secure bracketwith 5/16"-18x2" carriage bolts,lock washersand nuts (not provided).
(Figure4)
NOTE: The 1/4"-14x5/8" self-threading screws are not intended for use on wood doors.
FIGURE 1
FIGURE 3 FIGURE 4
FIGURE 2
Vertical
Reinforcement
Vertical
Centerline
of Garage Door
UP
Door Bracket
Vertical Reinforcement
Vertical Reinforcement
Horizontal Reinforcement
Vertical Centerline
of Garage Door
Hardware
(not provided)
Door Bracket
UP
Vertical
Centerline
of Garage Door
UP
Vertical Centerline of
Garage Door
Hardware
(not provided)
UP
Inside Edge of Door or
Reinforcement Board
Self-Threading Screw
Self-Threading
Screw
HARDWARE
Self-Threading Screw
1/4"-14x5/8"
18
Installation
STEP 8 Install the door bracket (continued)
OPTION B ONE-PIECE DOORS
1. Center the door bracketon the top ofthe door, in line with the header bracketas shown.
2. Mark either the leftand right, or the top and bottomholes.
Metal Doors:
l Drill 3/16" pilot holes and fasten the bracket with the self-threading screwsprovided.
WoodDoors:
l Drill 5/16" holes and use 5/16"-18x2" carriage bolts, lockwashers and nuts (not provided) or
5/16"x1-1/2" lag screws(notprovided) depending on your installation needs.
NOTE: The door bracket may be installed on the top edge of the door if required for your installation.
(Refer to the dotted line optional placement drawing.)
HARDWARE
Self-Threading Screw
1/4"-14x5/8"
For a door with no exposed
framing, or for the optional
installation, use lag screws
5/16"x1-1/2" (not provided)
to fasten the door bracket.
Vertical
Centerline
of Garage
Door
Optional
Placement
of Door
Bracket
Door Bracket
Header Bracket
Header Wall
2x4 Support
(Finished Ceiling)
Door
Bracket
Top of Door
(Inside Garage)
Top Edge of
Door
Optional
Placement
Optional
Placement
Top Edge
of Door
Top of Door
(Inside Garage)
Door
Bracket
Hardware
(not provided)
Hardware
(not provided)
Metal Door Wood Door
Self-Threading Screw
19
Installation
STEP 9 Connect the door arm to the trolley
Installation will vary according to the garage door type. Follow the instructionswhich apply to your door.
OPTION A SECTIONAL DOORS
IMPORTANT: The groove on the straightdoor arm MUST face away from the curved door arm.
1. Close the door. Disconnectthe trolley by pulling the emergency release handle.
2. Attach the straightdoor arm to the outer trolley using the clevispin.Secure with the ring
fastener.
3. Attach the curved door armto the door bracketusing the clevis pin.Secure with the ring
fastener.
4. Bring arm sections together.Find two pairs of holesthat line up and join sections.Select holes
as far apartaspossible to increase door arm rigidity and attach using the bolts, nuts, and lock
washers.
5. Pull the emergency release handle toward the garage door opener until the trolley release
arm is horizontal. The trolley will re-engage automatically when the garage door opener is
activated.
NOTE: If the holes in the curved door arm and the straight door arm do not align, reverse the straight
door arm, select two holes (as far apart as possible) and attach using bolts, nuts, and lock washers. If the
straight door arm is hanging down too far, you may cut 6 inches (15 cm) from the solid end.
20
Installation
STEP 9 Connect the door arm to the trolley (continued)
OPTION B ONE-PIECE DOORS
IMPORTANT: The groove on the straightdoor arm MUST face away from the curved door arm.
1. Close the door. Disconnectthe trolley by pulling the emergency release handle.
2. Fasten the straightdoor arm and the curved door armtogether to the longestpossible length
(with a 2 or 3 hole overlap) using the bolts,nuts, and lockwashers.
3. Attach the straightdoor arm to the door bracket using the clevispin.Secure with the ring
fastener.
4. Attach the curved door armto the trolley using the clevis pin.Secure with the ring fastener.
5. Pull the emergency release handle toward the garage door opener until the trolley release
arm is horizontal.
One-Piece Door without Track
One-Piece Door with Track
Ring Fastener
Ring Fastener
Ring Fastener
Nut
Nut
Ring Fastener
Lock Washer
Lock Washer
Clevis Pin 5/16"x1-1/4"
Clevis Pin
5/16"x1-1/4"
Hex Bolts
Hex Bolts
Clevis Pin
5/16"x1"
Clevis Pin
5/16"x1"
Straight Door Arm
(Groove facing out)
Curved Door Arm
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88

Chamberlain C610C Mode d'emploi

Catégorie
Porte de garage
Taper
Mode d'emploi

dans d''autres langues