Develco Humidity Guide d'installation

Marque: Develco

Modèle: Humidity

Taper: Guide d'installation

eng

Resetting

Resetting is needed if you want to connect your

humidity sensor to another gateway or if you

need to perform a factory reset to eliminate ab-

normal behaviour.

STEPS FOR RESETTING

1. Open the casing of the Humidity Sensor.

2. Press and hold the round menu button

inside the device.

Mounting

1. Open the casing of the Humidity Sensor and

remove the batteries.

Placement

• Place the sensor indoors at a temperature

between 0-50°C.

• Inside the room, in which you want to

monitor humidity levels.

• The Humidity Sensor should be placed on

a wall, reachable for battery testing and

maintenance.

Product description

The Humidity Sensor allows you to protect your

building and belongings by monitoring the

temperature and humidity levels, and receive

immediate alerts if the climate uctuates to

unsafe levels.

By supervising the indoor climate, the wireless

Humidity Sensor helps maintain the ideal

comfort level and protect interior, electronics,

musical instruments, furniture, artwork, and

other humidity-sensitive household items.

Humidity Sensor

2. Use double-sided tape or screws to attach

the sensor on the wall.

4. Make sure that the Humidity Sensor has

joined a network before closing the casing.

3. Insert batteries respecting the polarities.

50 cm

150 cm

WALL

Version 1.15

INSTALLATION MANUAL

Precautions

• Do not remove the product label as it

contains important information.

• Be aware that electronics are sensitive

to static electricity, so aim to discharge

before touching, and avoid touching any

components inside the device.

• Do not place the Humidity Sensor on

the ceiling, or behind obstacles, such as

curtains.

• Do not place the Humidity Sensor under

direct sunlight or bright light.

• Avoid placing the Humidity Sensor close to

radiators or electromagnetic elds.

• Do not paint the sensor.

1. Open the casing of the Humidity Sensor to

replace the batteries.

Fault nding

• If the search for a gateway has timed out, a

short press on the button will restart it.

• In case of a bad or wireless weak signal,

change the location of the Humidity Sensor.

Otherwise, you can relocate your gateway

or strengthen the signal with a smart plug.

2. Replace the batteries respecting the

polarities.

Battery replacement

The device will blink twice every minute when

the battery is low.

CAUTION:

• Do not attempt to recharge or open the

batteries.

• Risk of explosion if batteries are replaced by

an incorrect type.

• Dispose of a battery into re or a hot oven, or

mechanically crushing or cutting of a battery

can result in an explosion

• Leaving a battery in an extremely high

temperature surrounding environment can

result in an explosion or the leakage of

ammable liquid or gas.

• A battery subjected to extremely low air

pressure may result in an explosion or the

leakage of ammable liquid or gas

• Maximum operation temperature is 50°C /

122°F

• If you experience leakage from the batteries,

immediately wash your hands and/or any

aected area of your body thoroughly!

CAUTION: When removing cover for battery

change - Electrostatic Discharge (ESD) can

harm electronic components inside.

Disclaimers

CAUTION:

• Choking hazard! Keep away from children.

Contains small parts.

• Please follow the guidelines thoroughly. The

Humidity Sensor is a preventive, informing

device, not a guarantee or insurance that

sucient warning or protection will be

provided, or that no property damage,

theft, injury, or any similar situation will

take place. Develco Products cannot be

held responsible in case any of the above-

mentioned situations occur.

6. When the LED stops ashing, the Humidity

Sensor has successfully joined the Zigbee

network.

5. While the Humidity Sensor is searching for a

Zigbee network to join, the LED ashes red.

2. Insert two AA batteries respecting the

polarities.

3. The Humidity Sensor will now start search-

ing (up to 15 minutes) for a Zigbee network

to join.

4. Make sure that the Zigbee network is open

for joining devices and will accept the

Humidity Sensor.

Getting started

1. Open the sensor by pushing the switch and

pulling the top of the casing.

3. While you are holding the button down, the

LED rst ashes once, then two times in a

row, and nally numerous times in a row.

4. Release the button while the LED is ashing

numerous times in a row.

5. After you release the button, the LED shows

one long ash, and the reset is completed.

T00000047 Humidity Sensor installation manual, v1.15.indd 1T00000047 Humidity Sensor installation manual, v1.15.indd 1 10/7/2021 12:53:06 PM10/7/2021 12:53:06 PM

Other certications

• Zigbee Home Automation 1.2 compliant

Other certications

IC statement

Develco Products assumes no responsibility for

any errors, which may appear in this manual.

Furthermore, Develco Products reserves the

right to alter the hardware, software, and/

or specications detailed herein at any time

without notice, and Develco Products does

not make any commitment to update the

information contained herein. All the trademarks

listed herein are owned by their respective

owners.

Distributed by Develco Products A/S

Tangen 6

8200 Aarhus N

Denmark

www.develcoproducts.com

FCC statement

Changes or modications to the equipment not

expressly approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

NOTE: This equipment has been tested and

found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful

interference to radio or television reception,

which can be determined by turning the

equipment o and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

This device complies with FCC RF radiation

exposure limits set forth for an uncontrolled

FCC statement

ISED statement

Innovation, Science and Economic Develop-

ment Canada ICES-003 Compliance Label:

CAN ICES-3 (B)/NMB-3(B).

ISED statement

IN ACCORDANCE WITH THE DIRECTIVES

• Radio Equipment Directive (RED)

2014/53/EU

• RoHS Directive 2015/863/EU amending

2011/65/EU

CE certication

The CE mark axed to this product conrms

its compliance with the European Directives

which apply to the product and, in particular, its

compliance with the harmonized standards and

specications.

CE certication

Français

L’émetteur/récepteur exempt de licence

contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences

et Développement économique Canada

applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux

conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le

fonctionnement.

Cet équipement est conforme aux limites

d’exposition aux radiations IC CNR-102 établies

pour un environnement non contrôlé. Cet

équipement doit être installé et utilisé avec une

English

This device contains licence-exempt

transmitter(s)/receiver(s) that comply

with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two

conditions:

1. This device may not cause interference.

2. This device must accept any interference,

including interference that may cause

undesired operation of the device.

This equipment complies with IC RSS-102

radiation exposure limits set forth for an

uncontrolled environment. This equipment

should be installed and operated with minimum

distance 20 cm between the radiator and your

body.

Disposal

Dispose the product and batteries properly at

the end of life. This is electronic waste which

should be recycled.

3. Close the casing of the sensor.

j. environment. The antenna used for this

transmitter must be installed to provide a

separation distance of at least 20 cm from

all persons and must not be co-located or

operating in conjunction with any other antenna

or transmitter.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interfer-

ence, and

2. this device must accept any interference

received, including interference that may

cause undesired operation.

distance minimale de 20 cm entre le radiateur

et votre corps.

T00000047 Humidity Sensor installation manual, v1.15.indd 2T00000047 Humidity Sensor installation manual, v1.15.indd 2 10/7/2021 12:53:06 PM10/7/2021 12:53:06 PM