Acoustic B1000HD Class-D Bass Head Le manuel du propriétaire

B1000HD Class-D Bass Head
Acoustic
Marque
Acoustic
Modèle
B1000HD Class-D Bass Head
Catégorie
Équipement musical supplémentaire
Taper
Le manuel du propriétaire
OWNER’S MANUAL
www.acousticamplification.com
LIGHTWEIGHT CLASS D/NEODYMIUM BASS COMBOS
HIGH POWER CLASS D HEADS
BASS AMPLIFIERS
SERIES
|
LIGHTWEIGHT NEODYMIUM-LOADED BASS CABINETS
FCC Statements
1. Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
2. Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generate, uses, and can radiate radio
frequency energy and , in not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Acoustic
P.O. Box 5111
Thousand Oaks, CA
91359-5111
All trademarks and registered trademarks mentioned herein are recognized as the property
of their respective holders.
1507 - 1527703
Three Year Limited Warranty: Subject to the limitations set forth below,
Acoustic® hereby represents and warrants that the components of this
product shall be free from defects in workmanship and materials, including implied
warranties of merchantability or fitness for a particular purpose, subject to normal
use and service, for three (3) years to the original owner from the date of purchase.
Retailer and manufacturer shall not be liable for damages based upon
inconvenience, loss of use of product, loss of time, interrupted operation or
commercial loss or any other incidental or consequential damages including
but not limited to lost profits, downtime, goodwill, damage to or replacement
of equipment and property, and any costs of recovering, reprogramming, or
reproducing any program or data stored in equipment that is used with Acoustic®
products. This guarantee gives you specific legal rights. You may have other legal
rights which vary from state to state. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you.
The information contained herein is correct at the time of publication; yet, due to
continuing improvement and development, Acoustic® reserves the right to alter
specifications without prior notice.
3
B300HD, B600HD, B1000HD, BN3112, BN3115, BN6210, BN410, BN210, BN112, BN115
www.acousticamplification.com 3
SERIES
|
DANGER
Exposure to extremely high noise levels may cause permanent hearing loss. Individuals vary considerably
to noise-induced hearing loss but most will lose some hearing if exposed to intense noise for a sufficient
period of time.
The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the
following permissible noise level exposures:
According to OSHA, any exposure in the above permissible limits could result in some hearing loss. Ear
plugs or protectors in the ear canal or over the ears must be worn when operating this amplification system
in order to prevent a permanent hearing loss. If exposure in excess of the limits as put forth above, to insure
against potentially harmful exposure to high sound pressure levels, it is recommended that all persons
exposed to equipment capable of inducing high sound pressure levels, such as this amplification system,
be protected by hearing protectors while this unit is in operation.
DURATION PER DAY (HOURS) 8 6 4 3 2 1
SOUND LEVEL (dB) 90 93 95 97 100 103
DANGER
L’exposition a des niveaux eleves de bruit peut provoquer une perte permanente de l’audition, Chaque
organisme humain reagit differemment quant a la perte de l’audition, mais quasiment tout le monde subit
une diminution de l’acuite auditive lors d’une exposition suffisamment longue au bruit intense. Les autorites
competentes en reglementation de bruit ont defini les expositions tolerees aux niveaux de bruits:
Selon les autorites, toute exposition dans les limites citees ci-dessus, peuvent provoquer certaines pertes
d’audition. Des bouchons ou protections dans l’appareil auditif ou sur l’oreille doivent etre portes lors de
l’utilisation de ce systeme d’amplification afin de prevenir le risque de perte permanente de l’audition,
Dans le cas d’expositions superieures aux limites precitees il est recommande, afin de se premunir
contre les expositions aux pressions acoustiques elevees potentiellement dangeureuses, aux personnes
exposees aux equipements capables de delivrer de telles puissances, tels ce systeme d’amplification en
fonctionnement, de proteger l’appareil auditif.
DURE EN HEURES PAR JOUR 8 6 4 3 2 1
INIVEAU SONORE CONTINU EN dB 90 93 95 97 100 103
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding-type plug has two blades and
a third grounding prong. The wide blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use the attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. Refer all servicing to a qualified service professional. Servicing is required when the
apparatus does not operate normally or has been damaged in any way, including
damage to the power cord or plug, damage due to liquids spilled or objects dropped
inside the unit, dropping the unit, or anything else that interrupts normal use of the unit.
16. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to
rain or moisture.
17. When the MAINS plug, or an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.
18. Protective Ground Terminal: The apparatus shall be connected to an AC main socket with a
protective earth ground connection
1. Lisez ces instructions.
2. Conservez ces instructions.
3. Respectez tous les avertissements.
4. Suivez toutes les instructions.
5. N’utilisez pas cet appareil près de l’eau.
6. Nettoyez avec un chiffon sec.
7. Ne bloquez pas les ouvertures de ventilation. Installez-les conformément aux instructions du
fabricant.
8. Ne l’installez pas près de sources de chaleur telles que des radiateurs, des ouvertures, des
poêles ou d’autres appareils (incluant les amplificateurs) produisant de la chaleur.
9. Ne contournez pas le dispositif de sécurité de la fiche polarisée ou masse. Une fiche
polarisée possède deux lames dont une plus large que l’autre. Une fiche de terre a deux
lames et une troisième broche de masse. La lame large ou la troisième broche sont fournies
pour votre sécurité. Si la fiche fournie ne rentre pas dans votre prise, consultez un électricien
pour le remplacement de la prise obsolète.
10. Protégez le cordon d’alimentation pour qu’il ne soit pas piétiné ou pincé, en particulier au
niveau des fiches, des prises de courant et du point de sortie de l’appareil.
11. Utilisez uniquement les fixations / accessoires spécifiés par le fabricant.
12. Utilisez uniquement avec le chariot, le stand, le trépied, le support de table spécifiés
par le fabricant, ou vendus avec l’appareil. Lorsque vous utilisez un chariot, soyez
prudent(e) lorsque vous déplacez le chariot / l’appareil pour éviter des blessures dues au
renversement.
13. Débranchez cet appareil pendant les orages ou lorsqu’il n’est pas utilisé pendant de
longues périodes de temps.
14. Confiez toute réparation à un personnel qualifié. Une réparation est nécessaire lorsque
l’appareil a été endommagé de quelque façon que ce soit, comme par exemple si le
cordon d’alimentation ou la fiche sont endommagés, du liquide a été renversé ou des
objets sont tombés dans l’appareil, si l’appareil a été exposé à la pluie ou à l’humidité, s’il
ne fonctionne pas normalement ou s’il est tombé.
15. Pour toutes interventions techniques s’adresser à un technicien qualifié. L’intervention
technique est nécessaire lorsque l’appareil aété endommagé de n’importe quelle façon,
comme par exemple si le cordon secteur ou sa fiche sont détériorés,si du liquide acoulé ou
si des objets sont tombés à l’intérieur de l’apparei1 ,si l’appareil a été exposé à la pluie ou
à l’humidité, s’il ne fonctionne pas normalement ou s’il est tombé.
16. ATTENTION: Pour réduire le risque d’incendie ou de choc electrique ne pas exposer
l’appareil à la pluie ou à l’humidité.
17. Quand La prise MAINtS, au coupler, est utilisé pour la source d’alimentation êlectrique. Il
est conseillê de garder cette prise facilement accessible.
18. Borne de terre de protection: L’appareil doit être connecté à un connecteur AC principale
avec un raccordement à la terre de protection.
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANTES INSTRUCTIONS DE SECURITE
CE SYMBOLE APOUR BUT D’AVERTIR L’UTILISATEUR DE LA PRESENCE DE VOLTAGE DANGEREUX
NON-ISOLE A L’INTERIEUR DE CE PRODUIT QUI PEUT ETRE DE PUISSANCE SUFFISAMMENT
IMPORTANTE POUR PROVOQUER UN CHOC ELECTRIQUE AUX PERSONNES
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF NON-INSULATED
“DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT
MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS
CE SYMBOLE APOUR BUT D’AVERTIR L’UTILISATEUR DE LA PRESENCE D’INSTRUCTIONS
D’UTILISATION ET DE MAINTENANCE DANS LES DOCUMENTS FOURNIS AVEC CE PRODUIT
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING
AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING
THE UNIT.
APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED
WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.
AFIN DE REDUIRE LES RISQUÉ D’INCENDIE ET DE DECHARGE
ELECTRIQUE, NE PAS EXPOSER CET APPAREIL ALA PLUIE OU A L’HUMIDITE
BASS AMPLIFIERS OWNER’S MANUAL
www.acousticamplification.com
4
Congratulations on your purchase of a new Acoustic Class D/Neo
Series bass amplifier. Founded as the Acoustic Control Corporation
in Van Nuys, California in 1967, Acoustic is the rig of choice
for many legendary touring musicians. If you’re new to Acoustic
amps, we encourage you to get in tune with its rich heritage at
www.acousticamplification.com/history.cfm
Your comments are important. We constantly improve our products
based on feedback from musicians like you. Please feel free to contact
us at www.acousticamplification.com or send us an email at info@
acousticamplification.com.
Welcome to Acoustic, the Pro’s Tone Since 1967 ™.
WELCOME
SPECIFICATIONS
MODEL B1000HD B600HD B300HD
Power Rating 1000W (RMS - 4 ohms) 600W (RMS - 4 ohms) 300W (RMS - 4 ohms)
Inputs 1/4" with -10dB pad and
mute switch
1/4” with -10dB pad and
mute switch
1/4” with -10dB pad and
mute switch
Power Amp Type Class-D Class-D Class-D
Controls Master volume, overdrive volume,
gain, blend
Master volume, overdrive volume,
gain, blend
Master volume, overdrive volume,
gain, blend
Notch Filter Defeatable; adjustable from
50Hz to 1kHz
Defeatable; adjustable from
50Hz to 1kHz
Defeatable; adjustable from
50Hz to 1kHz
Main EQ 8-Band lit graphic (defeatable);
master low & high EQ
6-Band lit graphic (defeatable);
master low & high EQ
5-Band rotary EQ
EQ Frequency
Graphic EQ:
40Hz-63Hz-120Hz-350Hz-
800Hz-1.6kHz-3.2kHz-6.8kHz
Graphic EQ:
50Hz-120Hz-350Hz-800Hz-
1.6kHz-3.2kHz
Rotary EQ:
50Hz-120Hz-350Hz-800Hz-
3.2kHz
Super-Lo Boost Low pass shelf +3dB @ 40Hz Low pass shelf +3dB @ 40Hz Low pass shelf +3dB @ 40Hz
Super-Hi Boost High pass shelf +2dB @ 7kHz High pass shelf +2dB @ 7kHz High pass shelf +2dB @ 7kHz
Aux Input N/A 1/8” 1/8”
Headphone Jack N/A 1/8” 1/8”
Direct Out XLR w/Level control, pre-post EQ
switch & ground lift
XLR w/Level control, pre-post EQ
switch & ground lift
XLR w/Level control, pre-post EQ
switch & ground lift
Speaker Outs Dual locking-barrel type 1/4”, locking-barrel type 1/4”, locking-barrel type
Effects Loop 1/4” send/return (footswitchable) 1/4” send/return (footswitchable) 1/4” send/return (footswitchable)
Compressor “Acousti-comp™” w/ defeat switch
& indicator light
“Acousti-comp™” w/ defeat switch
& indicator light
“Acousti-comp™” w/ defeat switch
& indicator light
Other
Link in/out, tuner out;
footswitchable channel
(clean/overdrive)
Link in/out, tuner out;
footswitchable channel
(clean/overdrive)
Link in/out, tuner out;
footswitchable channel
(clean/overdrive)
Dimensions (LxWxH) 11.3” x 10.1” x 3”/28.6cm x
25.7cm 7.5cm
11.3” x 10.1” x 3”/28.6cm x
25.7cm 7.5cm
11.3” x 10.1” x 3”/28.6cm x
25.7cm 7.5cm
Weight 8.2 lbs/3.7kg 7.2 lbs/3.3kg 6.6 lbs/3.0kg
Optional Accessories Acoustic bass head carry bag
(Not included)
Acoustic bass head carry bag
(Not included)
Acoustic bass head carry bag
(Not included)
Bass Heads
B300HD, B600HD, B1000HD, BN3112, BN3115, BN6210, BN410, BN210, BN112, BN115
www.acousticamplification.com 5
SERIES
|
MODEL BN6210 BN3115 BN3112
Power Rating 600 watts total (4 ohms); 300
watts as stand-alone combo (8
ohm internal speaker load). Full
power achieved when external
speaker is connected
300 watts total (4 ohms): 150
watts as stand-alone combo (8
ohm internal speaker load). Full
power achieved when external
speaker is connected
300 watts total (4 ohms): 150
watts as stand-alone combo (8
ohm internal speaker load). Full
power achieved when external
speaker is connected
Speakers 2 X 10” custom neodymium
lo-frequency driver
1 X 15” custom neodymium
lo-frequency driver
1 X 12” custom neodymium
lo-frequency driver
Port Shelf Shelf Rear
Inputs 1/4” with -10dB pad
Switch/Mute/switch
1/4” with -10dB pad
Switch/Mute/switch
1/4” with -10dB pad
Switch/Mute/switch
Power Amp Type Class-D Class-D Class-D
Controls Master volume, overdrive volume,
gain, blend
Master volume, overdrive volume,
gain, blend
Master volume, overdrive volume,
gain, blend
Notch Filter Defeatable; adjustable from
50Hz to 1kHz
Defeatable; adjustable from
50Hz to 1kHz
Defeatable; adjustable from
50Hz to 1kHz
EQ 6-Band lit - graphic (defeatable);
super-hi & super-lo boost switch,
master low and high EQ
5-Band rotary EQ; super-hi &
super-lo boost switch
5-Band rotary EQ; super-hi &
super-lo boost switch
EQ Frequency Graphic EQ:
50Hz-120Hz-350Hz-800Hz-
1.6kHz-3.2kHz
Rotary EQ:
50Hz-120Hz-350Hz-800Hz-
3.2kHz
Rotary EQ:
50Hz-120Hz-350Hz-800Hz-
3.2kHz
Super-Lo Boost Low Pass Shelf +3dB @ 40Hz Low Pass Shelf +3dB @ 40Hz Low Pass Shelf +3dB @ 40Hz
Super-Hi Boost High Pass Shelf +2dB @ 7kHz High Pass Shelf +2dB @ 7kHz High Pass Shelf +2dB @ 7kHz
Aux Input 1/8" 1/8" 1/8”
Headphone Jack 1/8” 1/8" 1/8”
Direct Out XLR w/Level control, pre-post EQ
switch & ground lift
XLR w/Level control, pre-post EQ
switch & ground lift
XLR w/Level control, pre-post EQ
switch & ground lift
Speaker Outputs
¼” or locking-barrel combo jack
(can be used with ¼” in center
of jack)
1¼” or locking-barrel combo jack
(can be used with ¼” in center
of jack)
¼” or locking-barrel combo jack
(can be used with ¼” in center
of jack)
Effects Loop 1/4” send/return 1/4” send/return 1/4” send/return
Compressor “Acousti-comp™” w/ defeat switch
& indicator light
“Acousti-comp™” w/ defeat switch
& indicator light
“Acousti-comp™” w/ defeat switch
& indicator light
Other
Link in/out, tuner out;
footswitchable channel
(clean/overdrive)
Link in/out, tuner out;
footswitchable channel
(clean/overdrive)
Link in/out, tuner out;
footswitchable channel
(clean/overdrive)
Dimensions (LxWxH) 20.1” x 15.4” x 28”/51cm x
39cm x 71cm
20.1” x 15.4” x 28”/51cm x
39cm x 71cm
16.2” x 13.4” x 20.5”/ 41.1cm x
34cm x 52cm
Weight 59.7 lbs./27.1kg 58 lbs/26.4kg 40 lbs/18.2kg
Combos
BASS AMPLIFIERS OWNER’S MANUAL
www.acousticamplification.com
6
MODEL BN410 BN210 BN115 BN112
Power Handling (RMS) 800 Watts Rms/1600 Watts
Peak
600 Watts Rms/1200 Watts
Peak
500 Watts Rms/1000 Watts
Peak
400 Watts Rms/800 Watts
Peak
Speakers 4 X 10” custom neodymium
lo-frequency driver
2X10” custom neodymium
lo-frequency driver
1X 15” custom neodymium
lo-frequency driver
1X 12” custom neodymium
lo-frequency driver
Hi-Frequency Driver Switchable Switchable Switchable Switchable
Inputs Dual 1/4” (parallel),
locking barrel
Dual 1/4” (parallel),
locking barrel
Dual 1/4” (parallel),
locking barrel
Dual 1/4” (parallel),
locking barrel
Impedance 8 Ohms 8 Ohms 8 Ohms 8 Ohms
Handles Retractable spring-load
(side)
Retractable spring-load
(side); top pocket
Retractable spring-load
(side)
Retractable spring-load
(side); top pocket
Caster Sockets Yes N/A Yes N/A
Port Front Facing Shelf Rear Rear Rear
Dimensions (LxWxH) 24” x 16.1” x 27”/61.1cm x
41cm x 68.5cm
24” x 16.1” x 16.1”/61.1cm x
41cm x 41.01cm
24” x 16”’ x 24”/61cm x
40.6cm x 61cm
16.2” x 14.2” x 18.1” /
41.1cm x 36.1cm x 46cm
Weight 70.lbs/31.8kg 42.2 lbs/19.1kg 47.2 lbs/21.4kg 30lbs/13.6kg
Note: It is not recommended
to pair the BN112 with the
B1000HD.
Cabinets
B300HD, B600HD, B1000HD, BN3112, BN3115, BN6210, BN410, BN210, BN112, BN115
www.acousticamplification.com 7
SERIES
|
mute super-lo
input
clip
pad acousti-comp overdrive
gain overdrive blend
super-hi notch enable
50 120 350 800 3.2k notch master
aux in
power
SERIAL NO.
AC 120V~60Hz 330W
Fuse: T3.15A L 250V
minimum 4 O load
speaker
out
link out effects send footswitch
link in effects return tuner send
direct output
liftpre
eq post ground
level
B300HD
www.acousticamplification.com
B300HD
DESIGNED IN THE USA
Made in CHINA E467047
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
USE ONLY WITH A 250V FUSE
B300HD FRONT PANEL
1. Pad: Activates -10dB pad to reduce input sensitivity for use with active electronics basses or high output pickups. Indicator lights
blue when hi gain creates preamp clipping
2. Acoustic-comp™: Activates the built-in compression circuit. Light indicates compressor is active.
3. On/Off Switch: Activates the Overdrive circuit
4. Mute: Mutes the input signal
5. Super-lo: activates low frequency boost (+3dB at 40Hz).
6. Super-hi: activates high frequency boost (+2dB at 7kHz).
7. Notch Enable: activates the notch filter (#14).
8. Headphone Output: 1/8” 3-conductor jack for plugging in headphones. When used, it will disconnect the internal speaker
9. Bass Input: 1/4” two-conductor jack
Note: Turn the volume all the way down before plugging in your guitar and adjust the volume according to your taste.
10. Gain: Adjusts the input level signal gain of the amplifier
11. Overdrive: Controls the amount of overdrive when overdrive switch (#3) is engaged.
12. Blend: Adjusts the balance between the clean and overdrive channels when overdrive switch (#3) is engaged.
13. EQ: (knobs labeled 50 thru 3.2K): these adjust the EQ level from 0-10 at the noted frequencies
14. Notch: Adjusts the notch filter frequency from 50Hz (left) to 1kHz (right) when notch enable (#7) is engaged.
15. Master: Adjusts overall volume level of the amplifier
16. Aux In: This 3-conductor 1/8” media input jack will allow you to plug in a CD, MP3 player, or any other source so you can
practice along. To control the volume of the source, adjust the output volume of the device.
1
910 11 12
2 3 4 5 6 7 8
13 14 15 16
BASS AMPLIFIERS OWNER’S MANUAL
www.acousticamplification.com
8
mute super-lo
input
clip
pad acousti-comp overdrive
gain overdrive blend
super-hi notch enable
50 120 350 800 3.2k notch master
aux in
power
SERIAL NO.
AC 120V~60Hz 330W
Fuse: T3.15A L 250V
minimum 4 O load
speaker
out
link out effects send footswitch
link in effects return tuner send
direct output
liftpre
eq post ground
level
B300HD
www.acousticamplification.com
B300HD
DESIGNED IN THE USA
Made in CHINA E467047
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
USE ONLY WITH A 250V FUSE
1 2 3 5 7 9
3 4 6 8
B300HD BACK PANEL
1. AC Power Connection and Fuse: Connect included IEC power cable here. Fuse cap contains fuse for circuit protection
2. Power: Turns the amplifier on to ready for use
3. Speaker Outputs : 1/4” speaker jack and locking-barrel type jack for attaching external speakers (minimum 4 Ohm total load)
4. Link Out: Output to another Acoustic™ bass head. Allows user to run the B300HD in Master Mode to control another amp head.
This allows the user to link 2 heads together for more power and speakers controlled from one master amplifier
5. Link In: Input from another Acoustic™ bass head. Allows user to run the B300HD in Slave Mode controlled from another amp
head. This allows the user to link 2 heads together for more power and speakers controlled from one master amplifier
6. Effects Send: 1/4” two-conductor jack sends signal to an external effects or signal processing device
7. Effects Return: 1/4” two-conductor jack returns signal from an external effects or signal processing device
8. Footswitch: 1/4” Tip/Ring/Sleeve jack for attaching optional 2 button latching footswitch. Controls Overdrive on/off and
effects loop on/off
9. Tuner Send: Attach electronic instrument tuner via 1/4” 2 conductor instrument cable
10. Direct Output: XLR direct balanced output connector jack for connection to external PA or direct box
11. Pre/Post EQ Switch: Switches direct balanced output between pre and post EQ operation
12. Level: Adjusts the level of the direct output signal
13. Ground Lift: Lifts the ground from the XLR direct output. Useful for eliminating hum when the direct out is used
11 12 13
10
B300HD, B600HD, B1000HD, BN3112, BN3115, BN6210, BN410, BN210, BN112, BN115
www.acousticamplification.com 9
SERIES
|
B600HD FRONT PANEL
1. Pad: Activates -10dB pad to reduce input sensitivity for use with active electronics basses or high output pickups . Indicator lights
blue when hi gain creates preamp clipping
2. Acoustic-comp™: Activates the built-in compression circuit. Light indicates compressor is active.
3. On/Off Switch: Activates the Overdrive circuit
4. Mute: Mutes the input signal
5. Super-lo: activates low frequency boost (+3dB at 40Hz).
6. Super-hi: activates high frequency boost (+2dB at 7kHz).
7. Notch Enable: activates the notch filter (#17).
8. Headphone Output: 1/8” 3-conductor jack for plugging in headphones. When used, it will disconnect the internal speaker
9. Bass Input: 1/4” two-conductor jack
Note: Turn the volume all the way down before plugging in your guitar and adjust the volume according to your taste.
10. Gain: Adjusts the input level signal gain of the amplifier
11. Overdrive: Controls the amount of overdrive when overdrive switch (#3) is engaged.
12. Blend: Adjusts the balance between the clean and overdrive channels when overdrive switch (#3) is engaged.
13. EQ On/Off: engages the graphic EQ sliders (#14) when depressed. Indicator button and EQ sliders will light when active.
14. Graphic EQ (sliders labeled 50 thru 3.2K): These sliders increase or decrease the level of the associated frequency
15. Lo EQ: adjusts overall low frequency EQ +/-12dB @ 60Hz
16. Hi EQ: adjusts overall high frequency EQ +/-12dB @6kHz
17. Notch: Adjusts the notch filter frequency from 50Hz (left) to 1kHz (right) when notch enable (#7) is engaged.
18. Master: Adjusts overall volume level of the amplifier
19. Aux Input: This 3-conductor 1/8” media input jack will allow you to plug in a CD, MP3 player, or any other source so you can
practice along. To control the volume of the source, adjust the output volume of the device.
1
910 11 12
2 3 4 5 6 7 8
13 14 15 16 17 18 19
BASS AMPLIFIERS OWNER’S MANUAL
www.acousticamplification.com
10
1 2 3 5 7 9
3 4 6 8
B600HD BACK PANEL
1. AC Power Connection and Fuse: Connect included IEC power cable here. Fuse cap contains fuse for circuit protection
2. Power: Turns the amplifier on to ready for use
3. Speaker Outputs : 1/4” speaker jack and locking-barrel type jack for attaching external speakers (minimum 4 Ohm total load)
4. Link Out: Output to another Acoustic™ bass head. Allows user to run the B600HD in Master Mode to control another amp head.
This allows the user to link 2 heads together for more power and speakers controlled from one master amplifier
5. Link In: Input from another Acoustic™ bass head. Allows user to run the B600HD in Slave Mode controlled from another amp
head. This allows the user to link 2 heads together for more power and speakers controlled from one master amplifier
6. Effects Send: 1/4” two-conductor jack sends signal to an external effects or signal processing device
7. Effects Return: 1/4” two-conductor jack returns signal from an external effects or signal processing device
8. Footswitch: 1/4” Tip/Ring/Sleeve jack for attaching optional 2 button latching footswitch. Controls Overdrive on/off and
effects loop on/off
9. Tuner Send: Attach electronic instrument tuner via 1/4” 2 conductor instrument cable
10. Direct Output: XLR direct balanced output connector jack for connection to external PA or direct box
11. Pre/Post EQ Switch: Switches direct balanced output between pre and post EQ operation
12. Level: Adjusts the level of the direct output signal
13. Ground Lift: Lifts the ground from the XLR direct output. Useful for eliminating hum when the direct out is used
11 12 13
10
B300HD, B600HD, B1000HD, BN3112, BN3115, BN6210, BN410, BN210, BN112, BN115
www.acousticamplification.com 11
SERIES
|
B1000HD FRONT PANEL
1. Pad: Activates -10dB pad to reduce input sensitivity for use with active electronics basses or high output pickups . Indicator lights
blue when hi gain creates preamp clipping
2. Acoustic-comp™: Activates the built-in compression circuit. Light indicates compressor is active.
3. On/Off Switch: Activates the Overdrive circuit
4. Mute: Mutes the input signal
5. Super-lo: activates low frequency boost (+3dB at 40Hz).
6. Super-hi: activates high frequency boost (+2dB at 7kHz).
7. Notch Enable: activates the notch filter (#16).
8. Bass Input: 1/4” two-conductor jack
Note: Turn the volume all the way down before plugging in your guitar and adjust the volume according to your taste.
9. Gain: Adjusts the input level signal gain of the amplifier
10. Overdrive: Controls the amount of overdrive when overdrive switch (#3) is engaged.
11. Blend: Adjusts the balance between the clean and overdrive channels when overdrive switch (#3) is engaged.
12. EQ On/Off: engages the graphic EQ sliders (#13) when depressed. Indicator button and EQ sliders will light when active.
13. Graphic EQ (sliders labeled 40 — 6.8K): These sliders increase or decrease the level of the associated frequency
14. Lo EQ: adjusts overall low frequency EQ +/-12dB @ 60Hz
15. Hi EQ: adjusts overall high frequency EQ +/-12dB @6kHz
16. Notch: Adjusts the notch filter frequency from 50Hz (left) to 1kHz (right) when notch enable (#7) is engaged.
17. Master: Adjusts overall volume level of the amplifier
1
8910 11
2 3 4 5 6 7
12 14 15 16 1713
BASS AMPLIFIERS OWNER’S MANUAL
www.acousticamplification.com
12
1 2 3 5 7 9
3 4 6 8
B1000HD BACK PANEL
1. AC Power Connection and Fuse: Connect included IEC power cable here. Fuse cap contains fuse for circuit protection
2. Power: Turns the amplifier on to ready for use
3. Speaker Outputs : 2 X locking-barrel type jack for attaching external speakers (minimum 4 Ohm total load)
4. Link Out: Output to another Acoustic™ bass head. Allows user to run the B600HD in Master Mode to control another amp head.
This allows the user to link 2 heads together for more power and speakers controlled from one master amplifier
5. Link In: Input from another Acoustic™ bass head. Allows user to run the B600HD in Slave Mode controlled from another amp
head. This allows the user to link 2 heads together for more power and speakers controlled from one master amplifier
6. Effects Send: 1/4” two-conductor jack sends signal to an external effects or signal processing device
7. Effects Return: 1/4” two-conductor jack returns signal from an external effects or signal processing device
8. Footswitch: 1/4” Tip/Ring/Sleeve jack for attaching optional 2 button latching footswitch. Controls Overdrive on/off and effects
loop on/off
9. Tuner Send: Attach electronic instrument tuner via 1/4” 2 conductor instrument cable
10. Direct Output: XLR balanced output connector jack for connection to external PA or direct box
11. Pre/Post EQ Switch: Switches direct balanced output between pre and post EQ operation
12. Level: Adjusts the level of the direct output signal
13. Ground Lift: Lifts the ground from the XLR direct output. Useful for eliminating hum when the direct out is used
11 12 13
10
B300HD, B600HD, B1000HD, BN3112, BN3115, BN6210, BN410, BN210, BN112, BN115
www.acousticamplification.com 13
SERIES
|
BASS COMBOS
BN6210: 600 watt, 2 x 10” bass combo featuring our B600HD combined with two 10” custom Neodymium speakers.
Front facing shelf port.
BN3115 : 300 watt, 1 X 15” bass combo featuring our B300HD combined with a custom 15” Neodymium speaker.
Front facing shelf port
BN3112: 300 watt, 1 x 12” compact bass combo featuring our B300HD combined with a custom 12” Neodymium speaker.
Rear port.
BN3115
BN6210 BN3112
BASS AMPLIFIERS OWNER’S MANUAL
www.acousticamplification.com
14
BASS CABINETS
Our custom Neodymium drivers are nestled into a real plywood cabinet for lighter weight and superior performance. Front or rear ports
allow for extended bass response, while a defeatable hi-frequency driver allows control of extended high end.
Available in 4 configurations:
BN410: 4X10” Neodymium speakers, 800W RMS/1600W peak power handling, 8 ohm impedance, front-facing shelf port
for extreme low end.
BN210 : 2X10” Neodymium speakers, 600W RMS/1200W peak power handling, 8 ohm impedance, rear facing port for a tight,
super-focused low end
BN115: 1X15” Neodymium speaker, 500W RMS/1000W peak power handling, 8 ohm impedance, rear facing port provides warm,
fat low end.
BN112: 1X12” Neodymium speaker, 400W RMS/800W peak power handling, 8 ohm impedance, rear facing port in a super-
compact enclosure for extreme portability. A perfect complement for our BN3112 combo.
BN210BN410 BN112BN115
1. Horn On/Off Switch: Engages Piezo horn when in depressed position
2. Combo Locking Speaker Connector Jack: Connect amplifier head to
speaker cabinet via locking connector or 1/4” speaker connector
3. Parallel ¼” Speaker Jack: Connect amplifier head to speaker cabinet
via ¼” speaker connector. Can also use to connect another speaker
cabinet (in parallel) via additional 1/4” speaker cable connector.
Use left jack as input from amplifier head, and right jack as output to
additional cabinet.
4. 1/4” Speaker Input Jack: Connect amplifier head to speaker cabinet
via 1/4” speaker cable connector
1
23 4
www.acousticamplification.com
SERIES
|
BASS AMPLIFIERS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Acoustic B1000HD Class-D Bass Head Le manuel du propriétaire

B1000HD Class-D Bass Head
Acoustic
Marque
Acoustic
Modèle
B1000HD Class-D Bass Head
Catégorie
Équipement musical supplémentaire
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents