Winmate R12IBWS-MHM2 Guide de démarrage rapide

Please read these instructions carefully before using this product, and save this manual for future use.

Document Part Number: 915211101023

M-Series

HMI & Box PC

Quick Start Guide

V1.1

R12IBWS-MHM2

R15IBWS-MHC3

R17IBWS-MHM1

R19IBWS-MHA1

W22IBWS-MHA3

R12IHWS-MHM2

R15IHWS-MHC3

R17IHWS-MHM1

R19IHWS-MHA1

W22IHWS-MHA3

IBMH100

IHMH100

IKMH100

R12IKWS-MHM2

R15IKWS-MHC3

R17IKWS-MHM1

R19IKWS-MHA1

W22IKWS-MHA3

For more information on this and other Winmate

products, please visit our website at:

www.winmate.com

ii

FCC Statement

This device complies with part 15 FCC rules.

Operation is subject to the following two conditions:

 This device may not cause harmful interference.

 This device must accept any interference received

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

class "B" digital device, pursuant to part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at him own expense.

European Union

Electromagnetic Compatibility Directive (2014/30/EU)

 EN55024: 2010/ A1: 2015

o IEC61000-4-2: 2009

o IEC61000-4-3: 2006+A1: 2007+A2: 2010

o IEC61000-4-4: 2012

o IEC61000-4-5: 2014

o IEC61000-4-6: 2014

o IEC61000-4-8: 2010

o IEC61000-4-11: 2004

 EN55032: 2012/AC:2013

 EN61000-3-2:2014

 EN61000-3-3:2013

Low Voltage Directive (2014/35/EU)

 EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013

This equipment is in conformity with the requirement of the following EU

legislations and harmonized standards. Product also complies with the

Council directions.

iii

Copyright Notice

No part of this document may be reproduced, copied, translated, or transmitted in

any form or by any means, electronic or mechanical, for any purpose, without the

prior written permission of the original manufacturer.

Trademark Acknowledgement

Brand and product names are trademarks or registered trademarks of their

respective owners.

Disclaimer

Winmate Inc. reserve the right to make changes, without notice, to any product,

including circuits and/or software described or contained in this manual in order

to improve design and/or performance. We assume no responsibility or liability

for the use of the described product(s) conveys no license or title under any

patent, copyright, or masks work rights to these products, and make no

representations or warranties that these products are free from patent, copyright,

or mask work right infringement, unless otherwise specified. Applications that are

described in this manual are for illustration purposes only. We make no

representation or guarantee that such application will be suitable for the specified

use without further testing or modification.

Warranty

Winmate Inc. warranty guarantees that each of its products will be free from

material and workmanship defects for a period of one year from the invoice date.

If the customer discovers a defect, we will, at his/her option, repair or replace the

defective product at no charge to the customer, provide it is returned during the

warranty period of one year, with transportation charges prepaid. The returned

product must be properly packaged in its original packaging to obtain warranty

service. If the serial number and the product shipping data differ by over 30 days,

the in-warranty service will be made according to the shipping date. In the serial

numbers the third and fourth two digits give the year of manufacture, and the fifth

digit means the month (e. g., with A for October, B for November and C for

December).

For example, the serial number 1W16Axxxxxxxx means October of year 2016.

iv

Customer Service

We provide a service guide for any problem by the following steps: First, visit the

website of our distributor to find the update information about the product.

Second, contact with your distributor, sales representative, or our customer

service center for technical support if you need additional assistance.

You may need the following information ready before you call:

 Product serial number

 Software (OS, version, application software, etc.)

 Description of complete problem

 The exact wording of any error messages

In addition, free technical support is available from our engineers every business

day. We are always ready to give advice on application requirements or specific

information on the installation and operation of any of our products.

Safety Information

WARNING! / AVERTISSEMENT!

Always completely disconnect the power cord from your chassis

whenever you work with the hardware. Do not make connections

while the power is on. Sensitive electronic components can be

damaged by sudden power surges. Only experienced electronics

personnel should open the PC chassis.

Toujours débrancher le cordon d’alimentation du chassis lorsque

vous travaillez sur celui-ci. Ne pas brancher de connections

lorsque l’alimentation est présente. Des composantes

électroniques sensibles peuvent être endommagées par des sauts

d’alimentation. Seulement du personnel expérimenté devrait ouvrir

ces chassis.

CAUTION/ATTENTION

Always ground yourself to remove any static charge before

touching the CPU card. Modern electronic devices are very

sensitive to static electric charges. As a safety precaution, use a

grounding wrist strap at all times. Place all electronic components

in a static-dissipative surface or static-shielded bag when they are

not in the chassis.

Toujours verifier votre mise à la terre afin d’éliminer toute charge

statique avant de toucher la carte CPU. Les équipements

électroniques moderns sont très sensibles aux décharges

d’électricité statique. Toujours utiliser un bracelet de mise à la

terre comme précaution. Placer toutes les composantes

électroniques sur une surface conçue pour dissiper les charge, ou

dans un sac anti-statique lorsqu’elles ne sont pas dans le chassis.

v

CONTENTS

INTRODUCTION 1

Features 1

Package Contents 2

Product Overview 3

System Introduction 3

Display 4

Box PC 5

GETTING STARTED 9

Turning On Your Device 9

Connecting to AC Power Source 9

Connecting to DC Power Source 10

Turning Off Your Device 11

INSTALLATION 12

Wiring Requirements 12

Mounting 13

Panel Mounting 13

VESA Mounting 15

System Modifications 16

Detaching Box PC from Display 16

Attaching Box PC to the Display 19

SERVICE 21

Service Access 21

Hard Disk Replacement 23

APPENDIX 24

Appendix A: Cleaning the Monitor 24

1

INTRODUCTION

Congratulations on purchasing Winmate® M-Series HMI. M-Series HMI is

designed to provide versatile and cost-effective solution for your industrial needs.

P-CAP multi-touch screen equipped with industrial motherboard offers various

input/ output connectors. Fanless cooling system and powerful processor

assures steady performance and silent functioning.

M-Series HMI perfectly fits in applications where total costs of ownership (TCO)

and quick recovery of failure is important. The flexible system design provides

easy access to components and can be serviced by local maintenance team.

Versatile, easy-to-service and upgradable M-Series HMI is the best solution for

industrial and building automation.

Features

Winmate® M-Series HMI features:

 Signature true flat display screen with edge-to-edge design

 Aluminum, anti-corrosion treated housing

 Superior Sealing with front IP65 protection against dust and water

 Projected Capacitive Multi-Touch (P-CAP)

 Fanless cooling system

 Modular design

 Support wide range DC input with isolation

 Quick & Easy Removable 2.5” SSD Bay Slot

NOTE:

Some pictures in this guide are samples and can differ from actual

product

2

Package Contents

Carefully remove the box and unpack your device. Please check if all the items

listed below are inside your package. If any of these items are missing or

damaged contact us immediately.

Standard factory shipment list:

HMI Device

Quick Start Guide

(Hardcopy)

Driver CD & User

Manual

AC Adapter

(12V/ 80W)

Power Cable

Mounting Clips &

Screws

12.1” HMI – 8 pcs

15” HMI – 12 pcs

17”/ 19” HMI – 14 pcs

21.5” HMI – 16 pcs

3-pin Terminal Block

Female Connector Set

3

Product Overview

System Introduction

M-Series HMI is a flexible modular system that consists of the Front Display and

detachable Box PC from the rear side. Modular system design allows easy repair

and modifications.

4

Display

Display Front View

Display Side and Rear Views

5

Box PC

Box PC Front View

Box PC Top View

Box PC Bottom View

6

Input and Output Connectors Layout

Intel® Atom™

No

Description

No

Description

①

12-24V DC with isolation

⑧

COM1

②

LAN

⑨

Audio in

③

LAN

⑩

Audio out

④

USB 2.0 x 2

⑪

HDD indicator

⑤

USB 2.0 x 2

⑫

Reset

⑥

HDMI output

⑬

Power Button

⑦

VGA output

⑭

2.4” SSD Bay

7

Intel® Core™ i5 5200U

No

Description

No

Description

①

PCIe Slot cover for PCIe x 4

(1 x Half-length PCIe card)

⑨

COM2

②

12-24V DC with isolation

⑩

COM1

③

LAN

⑪

2.5” SSD Bay x 2

④

LAN

⑫

Audio out

⑤

USB 3.0 x 2

⑬

Audio in

⑥

USB 3.0 x 2

⑭

HDD indicators

⑦

HDMI output

⑮

Reset

⑧

VGA output

⑯

Power Button

8

Intel® Core™ i5 6200U

No

Description

No

Description

①

PCIe Slot Cover for one half-

length PCIe x4 card

⑩

Mic in

②

9-29V isolation DC-in

⑪

2.5” HDD x 1

③

Giga LAN

⑫

Expansion slot (Preliminary)*

④

Giga LAN

⑬

Line in

⑤

USB 3.0 x 2

⑭

Line out

⑥

USB 3.0 x 2

⑮

LED indicators

⑦

HDMI output

⑯

Reset

⑧

VGA Output

⑰

Power Button

⑨

COM2

*Expansion slot configurations (Preliminary):

 USB 2.0 x 4

 Giga LAN x 2

 COM x 2

 3G with SIM x 1

 USB 3.0 x 2

9

GETTING STARTED

Turning On Your Device

The HMI device will automatically turn on when connected to the power source.

Connecting to AC Power Source

To connect the HMI to AC power source:

1. Plug one end of the terminal block cable firmly to the DC Jack.

2. Plug the other end of the terminal block plug to the AC adapter.

3. Connect the AC adapter to the power cord.

4. Plug the power cord to a working AC outlet. The device will boot

automatically.

Note:

Power cords vary in appearance by region and country.

10

Connecting to DC Power Source

To connect the HMI to DC power source:

1. Insert the exposed wires of the DC Power Cable to the appropriate

connectors on the terminal block plug.

2. Plug the terminal block plug firmly to the DC IN Jack.

3. Connect the other end of the DC power cable (wires with lug terminals that

are labeled + and – to the terminals of the DC Power Source. Ensure that

the power connections maintain the proper polarity.

11

Turning Off Your Device

You can Turn OFF the HMI device with the Windows power settings.

To shut down the device:

1. Tap Start >Shut down.

2. Wait for your HMI device to completely turn off before disconnecting the

power cord (if necessary).

12

INSTALLATION

Wiring Requirements

The following common safety precautions should be observed before installing

any electronic device:

 Strive to use separate, non-intersecting paths to route power and

networking wires. If power wiring and device wiring paths must cross make

sure the wires are perpendicular at the intersection point.

 Keep the wires separated according to interface. The rule of thumb is that

wiring that shares similar electrical characteristics may be bundled together.

 Do not bundle input wiring with output wiring. Keep them separate.

 When necessary, it is strongly advised that you label wiring to all devices in

the system.

CAUTION

 Do not run signal or communication wiring and power wiring in the same

conduit. To avoid interference, wires with different signal characteristics

(i.e., different interfaces) should be routed separately.

 Be sure to disconnect the power cord before installing and/or wiring your

device.

 Verify the maximum possible current for each wire gauge, especially for the

power cords. Observe all electrical codes dictating the maximum current

allowable for each wire gauge.

 If the current goes above the maximum ratings, the wiring could overheat,

causing serious damage to your equipment.

 Be careful when handling the unit. When the unit is plugged in, the internal

components generate a lot of heat which may leave the outer casing too

hot to touch.

13

Mounting

M-series HMI devices come with different mounting options suitable for most of

the industrial and commercial applications.

Panel Mounting

Panel mounting solution allows installing the HMI device onto the wall or

instrument panel. M-Series comes with the mounting clamps and screws for fast

and easy mounting.

Cutout dimensions and mounting kit:

Cutout dimension ( W x D in mm)

12.1”

15”

17”

19”

21.5”

301 x 237

342 x 261

373 x 311

412 x 338

504 x 304

Mounting Clips

8 pcs

12 pcs

14 pcs

16 pcs

Screws

Short screws: 15mm M4

Long screws: 30mm M4

14

To mount the device to a sub frame or panel, do the following:

NOTE:

Use either short (15mm) or long (30mm) screws based on the

thickness of the wall.

La page est en cours de chargement...

Winmate R12IBWS-MHM2 Guide de démarrage rapide

Winmate R12IBWS-MHM2 Guide de démarrage rapide

dans d''autres langues

Documents connexes