DeWalt DW713 Mode d'emploi

Marque: DeWalt

Modèle: DW713

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

DW713

10" (254 mm) Compound Miter Saw

Scie à onglets mixtes de 254 mm (10 po)

Sierra ingletadora compuesta de 254 mm (10")

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

Before returning this product call

1-800-4-DEWALT

IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR D

WALT PURCHASE,

CALL 1-800-4-DEWALT

IN MOST CASES, A D

WALT REPRESENTATIVE CAN RESOLVE

YOUR PROBLEM OVER THE PHONE.

IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.

YOUR FEEDBACK IS VITAL TO THE SUCCESS OF D

WALT’S QUALITY

IMPROVEMENT PROGRAM.

Questions? Visit us at www.dewalt.com

Table of Contents

DEFINITIONS: SAFETY GUIDELINES .................................................................................1

IMPORTANT SAFETY INSTRUCTIONS ..............................................................................1

DOUBLE INSULATION/POLARIZED PLUG INSTRUCTIONS ..............................................1

SAFETY INSTRUCTIONS FOR ALL TOOLS ............…………………………………………1

ADDITIONAL SAFETY RULES ............. ……………………………………………………….2

ELECTRICAL CONNECTION .............…………………………………………………………3

ACCESSORIES ................................................................................................................... 3

OPTIONAL ACCESSORIES ...........……………………………………………………………3

SPECIFICATIONS ...........………………………………………………………………………4

UNPACKING YOUR SAW ..............……………………………………………………………4

FAMILIARIZATION ........... ………………………………………………………………………4

BENCH MOUNTING ...........……………………………………………………………………5

CHANGING OR INSTALLING A NEW SAW BLADE ....... ……………………………………5

TRANSPORTING THE SAW ..............…………………………………………………………6

ADJUSTMENTS .......... …………………………………………………………………………6

MITER SCALE ADJUSTMENT ....... ………………………………………………………6

MITER POINTER ADJUSTMENT .......……………………………………………………6

BEVEL SQUARE TO TABLE ........................................................................................6

BEVEL POINTER .........................................................................................................6

BEVEL STOP ...............................................................................................................7

FENCE ADJUSTMENT ... …………………………………………………………………7

GUARD ACTUATION AND VISIBILITY ...... ………………………………………………7

AUTOMATIC ELECTRIC BRAKE .................................................................................. 8

MITER LOCK ADJUSTMENT ....................................................................................... 8

BRUSHES ............………………………………………………………………………………8

OPERATION ............. ……………………………………………………………………………8

SWITCH ......................................................................................................................8

CUTTING WITH YOUR SAW .......................................................................................8

CROSSCUTS .................................................................................................................8

BEVEL CUTS .................................................................................................................9

QUALITY OF CUT ..........................................................................................................9

BODY AND HAND POSITION .......................................................................................9

CLAMPING THE WORKPIECE ....................................................................................9

TO INSTALL CLAMP ................................................................................................... 10

SUPPORT FOR LONG PIECES .................................................................................10

CUTTING PICTURE FRAMES, SHADOW BOXES

AND OTHER FOUR SIDED PROJECTS ....................................................................10

CUTTING TRIM MOLDING AND OTHER FRAMES ...................................................10

CUTTING COMPOUND MITERS ...............................................................................10

MITER SCALE ...........................................................................................................11

VERNIER SCALE .........................................................................................................11

WHEN MITERING TO THE RIGHT ............................................................................11

WHEN MITERING TO THE LEFT ...............................................................................11

CUTTING BASE MOLDING .......................................................................................11

CUTTING CROWN MOLDING ..................................................................................12

SPECIAL CUTS.................................................................................................................13

MAINTENANCE ................................................................................................................14

REPAIRS ...........................................................................................................................14

WARRANTY ......................................................................................................................14

TROUBLESHOOTING GUIDE ...........................................................................................15

COMPOUND MITER CUT REFERENCE CHART ..............................................................16

English

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may

result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D

WALT TOOL,

CALL US TOLL FREE AT: 1-800-4-D

EWALT (1-800-433-9258)

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Read all instructions before operating product. Failure to follow

all instructions listed below may result in electric shock, ﬁ re and/or serious

injury.

READ ALL INSTRUCTIONS

Double Insulation

Double insulated tools are constructed throughout with two separate layers of electrical

insulation or one single layer of reinforced insulation between you and the tool’s electrical

system. Tools built with this insulation system are not intended to be grounded. As a result,

your tool is equipped with a two prong plug which permits you to use extension cords without

concern for maintaining a ground connection.

NOTE: Double insulation does not take the place of normal safety precautions when

operating this tool. The secondary insulation system is for protection against injury resulting

from a possible failure of the primary insulation within the tool.

CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Repair or

replace damaged cords.

Polarized Plugs

Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk

of electric shock. When provided, this plug will fit in the polarized outlet only one way. If the

plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install the proper outlet. Do not change the plug in any way.

Safety Instructions For All Tools

WARNING: To reduce the risk of eye injury, ALWAYS use eye protection when

operating the miter saw.

• KEEP GUARD IN PLACE and in working order.

• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that

keys and adjusting wrenches are removed from spindle before turning tool on. Tools,

scrap pieces, and other debris can be thrown at high speed, causing injury.

• KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

• DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power

tools in damp or wet locations or in rain can cause shock or electrocution. Keep your work

area well-lit to avoid tripping or placing arms, hands, and fingers in danger.

• KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from work area.

Your shop is a potentially dangerous environment.

• MAKE WORKSHOP CHILDPROOF with padlocks, master switches, or by removing

starter keys. The unauthorized start-up of a machine by a child or visitor may result in

injury.

• DON’T FORCE TOOL. It will do the job better and be safer at the rate for which it was

designed.

• USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not

designed. Using the incorrect tool or attachment may result in personal injury.

• WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or

other jewelry to get caught in moving parts. Non-slip footwear is recommended. Wear

protective hair covering to contain long hair. Air vents may cover moving parts and should

also be avoided.

• ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses.

Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED

SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3)

• ANSI S12.6 (S3.19) hearing protection

• NIOSH/OSHA/MSHA respiratory protection

• SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece on the table

and against the fence or when your hand will be dangerously close to the blade [within

6" (152 mm)]. It is safer than using your hand and it frees both hands to operate tool.

• DON’T OVERREACH. Keep proper footing and balance at all times. Loss of balance

may cause personal injury.

• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest

performance. Follow instructions for lubricating and changing accessories. Poorly

maintained tools and machines can further damage the tool or machine and/or cause

injury.

• TURN THE MACHINE “OFF”, AND DISCONNECT THE MACHINE FROM THE

POWER SOURCE before installing or removing accessories, before adjusting or

changing set-ups, when making repairs or changing locations. An accidental start-up can

cause injury. Do not touch the plug’s metal prongs when unplugging or plugging in the

cord.

• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure that the switch is in

the “OFF” position before plugging in the power cord.

• USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.

If your product is equipped with a cordset, use only 3-wire extension cords that have

3-prong grounding-type plugs and 3-pole receptacles that accept the tool’s plug. When

using an extension cord, be sure to use one heavy enough to carry the current your

product will draw. An undersized cord will cause a drop in line voltage resulting in loss of

power and overheating. The following table shows the correct size to use depending on

cord length and nameplate ampere rating. If in doubt, use the next heavier gague. The

smaller the gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than

AWG

0 6 18 16 16 14

610 18161412

10 12 16 16 14 12

12 16 14 12 Not Recommended

English

• CHECK for DAMAGED PARTS. Before further use of the tool, a guard or other part

that is damaged should be carefully checked to determine that it will operate properly and

perform its intended function—check for alignment of moving parts, binding of moving

parts, breakage of parts, mounting and any other conditions that may affect its operation.

A guard or other part that is damaged should be properly repaired or replaced. Do not

use tool if switch does not turn it on and off.

• USE RECOMMENDED ACCESSORIES. Use only accessories that are recommended

by the manufacturer for your model. Accessories that may be suitable for one tool may be

hazardous when used on another tool. Consult the instruction manual for recommended

accessories. The use of improper accessories may cause risk of injury to persons.

• NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting

tool is unintentionally contacted.

• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave

tool until it comes to a complete stop. Serious injury can result.

• DO NOT OPERATE ELECTRIC TOOLS NEAR FLAMMABLE LIQUIDS OR IN

GASEOUS OR EXPLOSIVE ATMOSPHERES. Motors in these tools may spark and

ignite fumes.

• STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE COMMON SENSE. DO

NOT USE THE MACHINE WHEN YOU ARE TIRED OR UNDER THE INFLUENCE

OF DRUGS or ALCOHOL. A moment of inattention while operating power tools may

result in injury.

Additional Safety Rules For Miter Saws

WARNING: Do not allow familiarity (gained from frequent use of your saw) to replace safety

rules. Always remember that a careless fraction of a second is sufficient to inflict severe injury.

• DO NOT OPERATE THIS MACHINE until it is completely assembled and installed

according to the instructions. A machine incorrectly assembled can cause serious injury.

• OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are

not thoroughly familiar with the operation of this machine. Knowledge is safety.

• STABILITY. Make sure the miter saw is placed on a secure supporting surface and does

not slip or move during use.

• FOLLOW ALL WIRING CODES and recommended electrical connections to prevent

shock or electrocution. Protect electric supply line with at least a 15 ampere time-delay

fuse or a circuit breaker.

• MAKE CERTAIN the blade rotates in the correct direction. The teeth on the blade should

point in the direction of rotation as marked on the saw.

• TIGHTEN ALL CLAMP HANDLES, knobs and levers prior to operation. Loose clamps

can cause parts or the workpiece to be thrown at high speeds.

• BE SURE all blade and blade clamps are clean, recessed sides of blade clamps are

against blade and arbor screw is tightened securely. Loose or improper blade clamping

may result in damage to the saw and possible personal injury.

• ALWAYS USE A SHARP BLADE. Check the blade to see if it runs true and is free from

vibration. A dull or a vibrating blade can cause damage to the machine and/or serious

injury.

• DO NOT OPERATE ON ANYTHING OTHER THAN THE DESIGNATED VOLTAGE

for the saw. Overheating, damage to the tool and personal injury may occur.

• DO NOT WEDGE ANYTHING AGAINST THE FAN to hold the motor shaft. Damage to

tool and possible personal injury may occur.

• DO NOT force cutting action. Stalling or partial stalling of motor can cause damage.

To the machine or blade and/or serious injury.

• ALLOW THE MOTOR TO COME TO FULL SPEED prior to starting cut. Starting the

cut too soon may cause damage to the machine or blade and/or serious injury.

• NEVER CUT FERROUS METALS (Those with any iron or steel content) or masonry.

Either of these can cause the carbide tips to fly off the blade at high speeds causing

serious injury.

• DO NOT USE ABRASIVE WHEELS. The excessive heat and abrasive particles

generated by them may damage the saw and cause personal injury.

• NEVER have any part of your body in line with the path of the saw blade. Personal injury

will occur.

• NEVER apply blade lubricant to a running blade. Applying lubricant could cause your

hand to move into the blade resulting in serious injury.

• DO NOT place either hand in the blade area when the saw is connected to the power

source. Inadvertent blade activation may result in serious injury.

• DO NOT PERFORM FREE-HAND OPERATIONS (workpiece not supported by table

and fence). Hold the work firmly against the fence and table. Free-hand operations on a

miter saw could cause the workpiece to be thrown at high speeds, causing serious injury.

• NEVER REACH AROUND or behind the saw blade. A blade can cause serious injury.

• DO NOT reach underneath the saw unless it is unplugged and turned off. Contact with

saw blade may cause personal injury.

• SECURE THE MACHINE TO A STABLE SUPPORTING SURFACE. Vibration can

possibly cause the machine to slide, walk, or tip over, causing serious injury.

• USE ONLY CROSSCUT SAW BLADES recommended for miter saws. For best results,

do not use carbide tipped blades with hook angles in excess of 7 degrees. Do not use

blades with deep gullets. These can deflect and contact the guard, and can cause

damage to the machine and/or serious injury.

• USE ONLY BLADES OF THE CORRECT SIZE AND TYPE specified for this tool to

prevent damage to the machine and/or serious injury.

• INSPECT BLADE FOR CRACKS or other damage prior to operation. A cracked or

damaged blade can come apart and pieces can be thrown at high speeds, causing

serious injury. Replace cracked or damaged blades immediately.

• CLEAN THE BLADE AND BLADE CLAMPS prior to operation. Cleaning the blade

and blade clamps allows you to check for any damage to the blade or blade clamps. A

cracked or damaged blade or blade clamp can come apart and pieces can be thrown at

high speeds, causing serious injury.

• DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the

plastic guard. The polycarbonate material used in the guard is subject to attack by certain

chemicals.

• ALWAYS USE THE KERF PLATE AND REPLACE THIS PLATE WHEN DAMAGED.

Small chip accumulation under the saw may interfere with the saw blade or may cause

instability of workpiece when cutting.

• USE ONLY BLADE CLAMPS specified for this tool to prevent damage to the machine

and/or serious injury.

• CLEAN THE MOTOR AIR SLOTS of chips and sawdust. Clogged motor air slots can

cause the machine to overheat, damaging the machine and possibly causing a short

which could cause serious injury.

• KEEP ARMS, HANDS, AND FINGERS away from the blade to prevent severe cuts.

Clamp all workpieces that would cause your hand to be within 6" (152mm) of the saw

blade.

• NEVER LOCK THE SWITCH IN THE “ON” position. Severe personal injury may result.

• TURN OFF THE MACHINE and allow the blade to come to a complete stop before

raising the arm and prior to cleaning the blade area, removing debris in the path of the

blade, before servicing or adjusting tool. A moving blade can cause serious injury.

• PROPERLY SUPPORT LONG OR WIDE WORKPIECES. Loss of control of the

workpiece can cause injury.

English

ON GUARD:

DANGER – KEEP AWAY FROM BLADE.

ON UPPER GUARD:

PROPERLY SECURE BRACKET WITH BOTH SCREWS BEFORE

USE.

ON TABLE: (2 PLACES)

WARNING: FOR YOUR OWN SAFETY READ INSTRUCTION

MANUAL BEFORE OPERATING MITER SAW.

KEEP HANDS OUT OF PATH OF SAW BLADE.

DO NOT OPERATE SAW WITHOUT GUARDS IN PLACE.

CHECK LOWER GUARD FOR PROPER CLOSING BEFORE EACH USE.

ALWAYS TIGHTEN ADJUSTMENT BEFORE USE. DO NOT PERFORM ANY

OPERATION FREEHAND.

NEVER REACH IN BACK OF SAW BLADE. NEVER CROSS ARMS IN FRONT

OF BLADE. TURN OFF TOOL AND WAIT FOR SAW BLADE TO STOP BEFORE

MOVING WORKPIECE, CHANGING SETTINGS OR MOVING HANDS.

DISCONNECT POWER BEFORE CHANGING BLADE OR SERVICING.

TO REDUCE THE RISK OF INJURY, ALLOW SAW TO RETURN TO THE FULL UP

POSITION AFTER EACH OPERATION. THINK! YOU CAN PREVENT ACCIDENTS.

ON BASE: (2 PLACES)

Electrical Connection

Be sure your power supply agrees with the nameplate marking. 120 volts, AC means that

your saw will operate on alternating current only. A voltage decrease of 10 percent or more will

cause a loss of power and overheating. All D

EWALT tools are factory tested. If this tool does

not operate, check the power supply.

ACCESSORIES

WARNING: Since accessories, other than those offered by DEWALT, have not been tested

with this product, use of such accessories with this tool could be hazardous. To reduce the

risk of injury, only D

EWALT, recommended accessories should be used with this product.

Recommended accessories for use with your tool are available for purchase from your local

dealer or authorized service center. If you need assistance in locating any accessory for your

tool, please contact D

EWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286,

call 1-800-4-D

EWALT (1-800-433-9258) or visit our website www.dewalt.com.

OPTIONAL ACCESSORIES (FIG. 1)

The following accessories, designed for your saw, may be helpful. In some cases, other locally

obtained work supports, length stops, clamps, etc., may be more appropriate. Use care in

selecting and using accessories.

Extension, Work Support: DW7080

Used to support long overhanging workpieces, the work support is user assembled. Your

saw table is designed to accept two work supports; one on each side.

Adjustable Length Stop: DW7051 (not shown)

Requires the use of one work support. It is used to make repetitive cuts of the same length

from 0 to 42" (107cm).

Clamp: DW7082

Used for firmly clamping workpiece to the saw fence for precision cutting.

Dust Bag: DW7053 (Included with some models)

Equipped with a zipper for easy emptying, the dust bag will capture the majority of the

sawdust produced (not shown).

• NEVER cross arms in front of blade while using tool. Always make a dry run (unpowered)

before making a finish cut so that you can check the path of the blade or severe personal

injury may result.

• ADDITIONAL INFORMATION regarding the safe and proper operation of power tools

(i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue,

Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available

from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please

refer to the American National Standards Institute ANSI 01.1 Safety Requirements for

Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

WARNING: Do not connect unit to electrical power source until complete instructions are

read and understood.

WARNING: Always wear proper personal hearing protection that conforms to

ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from

this product may contribute to hearing loss.

WARNING: NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON THE

TABLE AND AGAINST THE FENCE.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as dust masks that are specially designed to filter out

microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding,

drilling, and other construction activities. Wear protective clothing and wash

exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay

on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious

and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory

protection appropriate for the dust exposure. Direct particles away from face and body.

For your convenience and safety, the following warning labels are on your miter saw.

ON MOTOR HOUSING:

WARNING: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL

BEFORE OPERATING SAW.

WHEN SERVICING, USE ONLY IDENTICAL RE PLACE MENT PARTS.

ALWAYS WEAR EYE PROTECTION.

DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS.

ON MOVING FENCE:

ALWAYS ADJUST FENCE PROPERLY

BEFORE USE. CLAMP SMALL PIECES

BEFORE CUTTING. SEE MANUAL.

English

Crown Molding Fence: DW7084

Used for precision cutting of crown molding.

Miter Saw Replacement Kerf Plate: DW7055 (not shown)

This durable plastic uncut plate limits blade tear out.

Miter Saw Stands: DWX723, DWX724, DWX725B (not shown)

Provides stable and accurate work platform for miter saws.

DW7080

LOCKNUTS

END PLATE

DW7082

DW7084

FIG. 1

SAW BLADES: ALWAYS USE 10" (254mm) SAW BLADES WITH 5/8" (16 mm) ARBOR

HOLES. SPEED RATING MUST BE AT LEAST 5500 RPM. Never use a smaller diameter

blade. It will not be guarded properly. Use crosscut blades only! Do not use blades designed

for ripping, combination blades or blades with hook angles in excess of 7 degrees.

BLADE DESCRIPTIONS

APPLICATION DIAMETER TEETH

Construction Saw Blades (thin kerf with anti-stick rim)

General Purpose 10" (254 mm) 40

Fine Crosscuts 10" (254 mm) 60

Woodworking Saw Blades (provide smooth, clean cuts)

Fine crosscuts 10" (254 mm) 80

Non-ferrous metals 10" (254 mm) 80

NOTE: For cutting non-ferrous metals, use only saw blades with

TCG teeth designed for this purpose.

Speciﬁ cations

CAPACITY OF CUT

50° miter left and right

48° bevel left: 3° right

0° miter

Max. Height 3.5" (89mm) Result Width 3.5" (89mm)

Max. Width 6.1" (155mm) Result Height 1.25" (32mm)

45° miter

Max. Height 3.5" (89mm) Result Width 2.4" (61mm)

Max. Width 4.2" (107mm) Result Height 1.25" (32mm)

45° bevel

Max. Height 2.3" (58mm) Result Width 3.5" (89mm)

Max. Width 6.1" (155mm) Result Height .75" (19mm)

31.62° miter and 33.85° bevel

Max. Width 5.25" (133mm) Result Height .9" (23mm)

DRIVE

120 Volt Motor

2200 Watts 15 Amp Motor

5000 RPM Cut Helical Gears with Roller and Ball Bearings

Carbide Tooth Blade Automatic Electric Brake

Unpacking Your Saw

Check the contents of your miter saw carton to make sure that you have received all parts. In

addition to this instruction manual, the carton should contain:

1. One No. DW713 miter saw with blade.

2. One blade wrench in wrench pocket shown in Figure 2.

3. One No. DW7053 Dust Bag.

Familiarization

Your miter saw is fully assembled in the carton.

FIG. 1A

Open the box and lift the saw out by the convenient

carrying handle, as shown in Figure 1A.

Place the saw on a smooth, flat surface such as a

workbench or strong table.

Examine Figures 2 and 3 to become familiar with

the saw and its various parts. The section on

adjustments will refer to these terms and you must

know what and where the parts are.

CAUTION: Pinch Hazard. To reduce the risk of

injury, keep thumb underneath the handle when

pulling the handle down. The lower guard will move up as the handle is pulled down which

could cause pinching.The handle is placed close to the guard for special cuts.

Press down lightly on the operating handle and pull out the lock down pin, as shown in

Figure6. Gently release the downward pressure and allow the arm to rise to its full height. Use

the lock down pin when carrying the saw from one place to another. Always use the carrying

handle to transport the saw or the hand indentations shown in Figure 2 and 3.

English

IMPORTANT SAFETY INSTRUCTIONS

Changing or Installing a New Saw Blade (Fig. 3–5)

WARNING: To reduce the risk of serious personal injury, turn off the tool and

disconnect it from the power source before attempting to move it, change

accessories or make any adjustments.

CAUTION:

• Never depress the spindle lock button while the blade is under power or coasting.

• Do not cut ferrous metal (containing iron or steel) or masonry or fiber cement product

with this miter saw.

Removing the Blade

1. Unplug the saw.

2. Raise the arm to the upper position and raise the lower guard as far as possible.

3. Loosen, but do not remove guard bracket screw until the bracket can be raised far

enough to access the blade screw. Lower guard will remain raised due to the position of

the guard bracket screw (Fig. 4).

4. Depress the spindle lock button (Fig. 3) while carefully rotating the saw blade by hand until

the lock engages.

Bench Mounting

Holes are provided in all four feet to facilitate bench mounting, as shown in Figure 2. (Two

different sized holes are provided to accommodate different sizes of screws. Use either hole, it

is not necessary to use both.) Always mount your saw firmly to prevent movement. To enhance

the tool’s portability, it can be mounted to a piece of 1/2" (12.7 mm) or thicker plywood which

can then be clamped to your work support or moved to other job sites and reclamped.

NOTE: If you elect to mount your saw to a piece of plywood, make sure that the mounting

screws don’t protrude from the bottom of the wood. The plywood must sit flush on the work

support. When clamping the saw to any work surface, clamp only on the clamping bosses

where the mounting screw holes are located. Clamping at any other point will surely interfere

with the proper operation of the saw.

CAUTION: To prevent binding and inaccuracy, be sure the mounting surface is not warped

or otherwise uneven. If the saw rocks on the surface place a thin piece of material under one

saw foot until the saw sits firmly on the mounting surface.

FIG. 2

LOWER

GUARD

RIGHT SIDE

FENCE

MITER LOCK

LEVER

MITER SCALE

BENCH

MOUNTING

HOLES

LEFT SIDE FENCE

CLAMPING KNOB

OPERATING

HANDLE

TABLE

BASE

HOLES FOR

EXTENSION KIT

FIG. 3

TRIGGER

SWITCH

CARRYING

HANDLE

SPINDLE LOCK

BUTTON

LEFT SIDE

FENCE

MOTOR

HOUSING

BEVEL

SCALE

MITER DETENT

MITER

SCALE

HAND

INDENTATION

BEVEL CLAMP

KNOB

DUST

SPOUT

MOTOR END

CAP

WRENCH

MITER DETENT

OVER RIDE

English

5. Keeping the button depressed, use the other hand and the wrench provided to loosen

the blade screw. (Turn clockwise, left-hand threads.)

6. Remove the blade screw, outer blade clamp, and blade. The inner blade clamp may be

left on the spindle.

FIG. 4

GUARD

BRACKET

SCREW

WRENCH

FIG. 5

BLADE

OUTER

CLAMP

WASHER

INNER CLAMP

WASHER

BLADE

SCREW

Installing a Blade

1. Unplug the saw.

2. With the arm raised, the lower guard held open and the guard bracket, place the blade

on the spindle against the inner blade clamp with the teeth at the bottom of the blade

pointing toward the back of the saw.

3. Assemble the outer blade clamp onto the spindle.

4. Install the blade screw and, engaging the spindle lock, tighten the screw firmly with

wrench provided. (Turn counterclockwise, left-hand threads.)

5. Return the guard bracket to its original position and firmly tighten the guard bracket screw

to hold bracket in place.

WARNING:

• The guard bracket must be returned to its original position

and the screw tightened before activating the saw.

• Failure to do so may allow the guard to contact the

spinning saw blade resulting in damage to the saw and

severe personal injury.

Transporting the Saw (Fig. 3, 6)

WARNING: To reduce the risk of serious personal injury, turn off the tool and

disconnect it from the power source before attempting to move it, change

accessories or make any adjustments.

WARNING: To reduce the risk of serious personal injury, ALWAYS lock the miter lock

handle, bevel lock handle, lock down pin, and fence adjustment knob before transporting

saw.

In order to conveniently carry the miter saw from place to place, a carrying handle has been

included on the top of the saw arm, as shown in Figure 3. To transport the saw, lower the

arm and depress the lock down pin shown in Figure 6.

FIG. 6

LOCK

DOWN

ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn off the tool and

disconnect it from the power source before attempting to move it, change

accessories or make any adjustments.

NOTE: Your miter saw is fully and accurately adjusted at the factory at the time of manufacture.

If readjustment due to shipping and handling or any other reason is required, follow the steps

below to adjust your saw.

Once made, these adjustments should remain accurate. Take a little time now to follow these

directions carefully to maintain the accuracy of which your saw is capable.

MITER SCALE ADJUSTMENT (FIG. 7, 8)

Place a square against the saw’s fence and blade, as shown in Figure 7. (Do not touch the tips

of the blade teeth with the square. To do so will cause an inaccurate measurement.) Unlock

miter lock lever (see Fig. 8) and swing the miter arm until the miter detent locks it at the 0˚

miter position. Do not lock miter lock lever. If the saw blade is not exactly perpendicular to

the fence, loosen the three screws that hold the miter scale to the base (shown in Fig. 8) and

move the scale/miter arm assembly left or right until the blade is perpendicular to the fence,

as measured with the square. Retighten the three screws. Pay no attention to the reading of

the miter pointer at this point.

MITER POINTER ADJUSTMENT (FIG. 8, 9)

Unlock miter lock lever and squeeze the miter detent to move the miter arm to the zero

position, as shown in Figure 8. Unlock the miter lock lever to allow the miter detent to snap

into place as you rotate the miter arm past zero. Observe the pointer and miter scale through

the viewing opening shown in Figure 9. If the pointer does not indicate exactly zero, loosen the

pointer screw, adjust the pointer to 0˚ and retighten.

BEVEL SQUARE TO TABLE (FIG. 10, 11)

To align the blade square to the rotary table, lock the arm in the down position. Place a square

against the blade taking care to not have the square on top of a tooth, as shown in Figure10.

Loosen the bevel clamp knob so that you can move the bevel arm. Move the bevel arm as

necessary so that the blade is at 0° bevel to the table. If the bevel arm needs adjustment,

loosen the lock nut on the right side bevel stop as shown in Figure 11, and adjust the stop

screw as necessary. Hold the stop screw in place and tighten the lock nut.

BEVEL POINTER (FIG. 11)

If the bevel pointer does not indicate zero, loosen the screw that holds it in place and move

the pointer as necessary.

English

Suggestion: For accuracy, set the top edge so that it aligns

with zero.

BEVEL STOP (FIG. 12, 13)

To set the 45° bevel stop shown in Figure 12, first loosen

the left side fence clamping knob and slide the left side

fence as far as it will go to the left. Move the arm to the left

until it stops on the left bevel stop screw. If the bevel pointer

does not indicate exactly 45°, loosen the left side bevel stop

lock nut and turn the screw downwards. Move the arm to

the left and tighten the bevel clamp knob firmly when the

bevel pointer indicates exactly 45°. Adjust the left side bevel

stop screw upwards until it firmly touches the bevel stop.

Retighten the nut while holding the screw from turning.

To achieve 3° right bevel or 48° left bevel, the stop screws

must be adjusted to allow the arm to move to the desired

location. The bevel stops will need readjustment to the zero

and 45° positions after cuts are made.

FENCE ADJUSTMENT (FIG. 13)

WARNING: To reduce the risk of serious personal

injury, turn off the tool and disconnect it from the

power source before attempting to move it, change

accessories or make any adjustments.

To bevel UP TO 48° left, the left side of the fence can be

adjusted to the left to provide clearance. To adjust the fence,

loosen the fence clamping knob shown in Figure 13 and slide

the fence to the left. Make a dry run with the saw turned

off and check for clearance. Adjust the fence to be as

close to the blade as practical to provide maximum

workpiece support, without interfering with arm up and

down movement. Tighten the fence clamping knob securely.

When the bevel operations are complete, don’t forget to

relocate the fence to the right.

GUARD ACTUATION AND VISIBILITY (FIG. 24)

CAUTION: Pinch Hazard. To reduce the risk of injury,

keep thumb underneath the handle when pulling the handle

down. The lower guard will move up as the handle is pulled

down which could cause pinching.

The blade guard on your saw has been designed to

automatically raise when the arm is brought down and to

lower over the blade when the arm is raised.

The guard can be raised by hand when installing or

removing saw blades or for inspection of the saw. NEVER

RAISE THE BLADE GUARD MANUALLY UNLESS THE

SAW IS TURNED OFF.

NOTE: Certain special cuts will require that you manually

raise the guard. Refer to Cutting Large Material under

Special Cuts.

The front section of the guard is louvered for visibility while

cutting. Although the louvers dramatically reduce flying

debris, there are openings in the guard and safety glasses

should be worn at all times when viewing through the

louvers.

FIG. 9

MITER

SCALE

POINTER

FIG. 10

FIG. 7

FIG. 8

MITER

LOCK

LEVER

MITER

SCALE

ADJUSTMENT

SCREW

(three of these)

MITER

DETENT

BEVEL CLAMP

KNOB

STOP SCREW

LOCK NUT

FIG. 11

BEVEL STOP

BEVEL

POINTER

SCREW

BEVEL

SCALE

STOP

SCREW

LOCK

NUT

FIG. 12

BEVEL

POINTER

BEVEL

CLAMP

KNOB

English

OPERATION

WARNING: To reduce the risk of serious personal

injury, turn off the tool and disconnect it from the

power source before attempting to move it, change

accessories or make any adjustments.

WARNING: Always use eye protection. All users and

bystanders must wear eye protection that conforms to ANSI

Z87.1 (CAN/CSA Z94.3).

Plug the saw into any household 60 Hz power source.

Refer to the nameplate for voltage. Be sure the cord will not

interfere with your work.

SWITCH (FIG. 14)

To turn the saw on, depress the trigger switch shown in

Figure 14. To turn the tool off, release the switch. There is

no provision for locking the switch on, but a hole is provided

in the trigger for insertion of a padlock to lock the saw off.

CUTTING WITH YOUR SAW

NOTE: Although this saw will cut wood and many non-

ferrous materials, we will limit our discussion to the cutting

of wood only. The same guidelines apply to the other

materials. DO NOT CUT FERROUS (IRON AND STEEL)

MATERIALS OR MASONRY WITH THIS SAW. Do not

use any abrasive blades.

CROSSCUTS

Cutting of multiple pieces is not recommended but can be

done safely by ensuring that each piece is held firmly against

the table and fence. A crosscut is made by cutting wood

across the grain at any angle. A straight crosscut is made

with the miter arm at the zero degree position. Set the miter

arm at zero, hold the wood on the table and firmly against

the fence. Turn on the saw by squeezing the trigger switch

shown in Figure 14.

When the saw comes up to speed (about 1 second) lower

the arm smoothly and slowly to cut through the wood. Let

the blade come to a full stop before raising arm.

CAUTION: Always use a work clamp to maintain control

and reduce the risk of workpiece damage and personal

injury.

Miter crosscuts are made with the miter arm at some angle

other than zero. This angle is often 45° for making corners,

but can be set anywhere from zero to 50° left or right. After

selecting the desired miter angle, be sure to tighten the miter

lock lever. Make the cut as described above.

To cut through an existing pencil line on a piece of wood,

match the angle as close as possible. Cut the wood a little

too long and measure from the pencil line to the cut edge

to determine which direction to adjust the miter angle and

recut. This will take some practice, but it is a commonly

used technique.

AUTOMATIC ELECTRIC BRAKE

Your saw is equipped with an automatic electric blade brake

which stops the saw blade within 5 seconds of trigger

release. This is not adjustable.

On occasion, there may be a delay after trigger release to

brake engagement. On rare occasions, the brake may not

engage at all and the blade will coast to a stop.

If a delay or “skipping” occurs, turn the saw on and off 4 or

5 times. If the condition persists, have the tool serviced by

an authorized D

EWALT service center.

Always be sure the blade has stopped before removing it

from the kerf plate. The brake is not a substitute for guards

or for ensuring your own safety by giving the saw your

complete attention.

MITER LOCK ADJUSTMENT (FIG. 15)

The miter lock rod should be adjusted if the table of the saw

can be moved when the miter lock handle is locked down.

To adjust, put the miter lock handle in the up position. Using

a slotted screwdriver, adjust the lock rod in 1/8 clockwise

turn increments to increase the lock force. To ensure the

miter lock is functioning properly, re-lock miter lock handle

to a non-detent miter angle.

NOTE: Some models may have a set screw as shown in

Figure 15. Using a 3/32 hex wrench, loosen the set screw

on the pivot pin. Tighten set screw after adjustment is

complete.

Brushes (Fig. 3)

WARNING: To reduce the risk of serious personal

injury, turn off the tool and disconnect it from the

power source before attempting to move it, change

accessories or make any adjustments.

Inspect carbon brushes regularly by unplugging the tool,

removing the motor end cap (Fig. 3) and removing the brush

cap that holds the spring-loaded brush assembly. Keep

brushes clean and sliding freely in their guides. Always replace

a used brush in the same orientation in the holder as it was

prior to its removal. Carbon brushes have varying symbols

stamped into their sides, and if the brush is worn down to

approximately 1/2" (12.7 mm), the spring will no longer exert

pressure and they must be replaced. Use only identical

EWALT brushes. Use of the correct grade of brush is

essential for proper operation of electric brake. New brush

assemblies are available at D

EWALT service centers. The

tool should be allowed to “run in” (run at no load) for 10

minutes before use to seat new brushes. The electric brake

may be erratic in operation until the brushes are properly

seated (worn in). Always replace the brush inspection cap

after inspection or servicing the brushes.

While “running in” DO NOT TIE, TAPE, OR OTHER WISE

LOCK THE TRIGGER SWITCH ON. HOLD BY HAND ONLY.

FIG. 14

TRIGGER

SWITCH

HOLE FOR PADLOCK

FIG. 15

SET SCREW (IF EQUIPPED)

SLOTTED

ADJUSTMENT

ROD

LEFT SIDE

FENCE

CLAMPING

KNOB

FIG. 13

LEFT SIDE

BEVEL STOP

SCREW

INSTALL

HOLE FOR

CLAMP

English

BEVEL CUTS (FIG. 12)

A bevel cut is a crosscut made with the saw blade at a

bevel to the wood. In order to set the bevel, loosen the bevel

clamp knob and move the saw to the left as desired. (It is

necessary to move the left side of the fence to allow

clearance). Once the desired bevel angle has been set,

tighten the bevel clamp knob firmly.

Bevel angles can be set from 3° right to 48° left and can be

cut with the miter arm set between zero and 50° right or left.

Ensure the fence has been adjusted properly. When cutting

left bevel, or right miter compound cuts, it will be necessary

to remove the adjustable fence.

QUALITY OF CUT

The smoothness of any cut depends on a number of things

contributing to the quality of the cut are: material being cut,

blade type, blade sharpness and rate of cut all contribute

to the quality of the cut.

When smoothest cuts are desired for molding and other

precision work, a sharp (60–80 tooth carbide) blade and a

slower, even cutting rate will produce the desired results.

Ensure that material does not creep while cutting. Clamp it

securely in place. Always let the blade come to a full stop

before raising arm.

If small fibers of wood still split out at the rear of the

workpiece, apply a piece of masking tape on the wood

where the cut will be made. Saw through the tape and

carefully remove tape when the cut is finished.

For varied cutting applications, refer to the list of

recommended saw blades for your saw and select the

one that best fits your needs. Refer to Saw Blades under

Accessories for correct saw blade.

BODY AND HAND POSITION (FIG. 16)

Proper positioning of your body and hands when operating

the miter saw will make cutting easier, more accurate and

safer. Never place hands near cutting area (Fig 16A). Place

hands no closer than 6" (152 mm) from the blade. Hold the

workpiece tightly to the table and the fence when cutting.

Keep hands in position until the trigger has been released

and the blade has completely stopped. ALWAYS MAKE

DRY RUNS (UNPOWERED) BEFORE FINISH CUTS SO

THAT YOU CAN CHECK THE PATH OF THE BLADE. DO

NOT CROSS ARMS, AS SHOWN IN FIGURE16A.

Keep both feet firmly on the floor and maintain proper

balance. As you move the miter arm left and right, follow it

and stand slightly to the side of the saw blade. Sight through

the guard louvers when following a pencil line.

CLAMPING THE WORKPIECE

WARNING: To reduce the risk of serious personal

injury, turn off the tool and disconnect it from the

power source before attempting to move it, change

accessories or make any adjustments.

PROPER HAND POSITION

FIG. 16

IMPROPER HAND POSITION

FIG. 16A

PROPER HAND POSITION

IMPROPER HAND POSITION

English

WARNING: A workpiece that is clamped, balanced and

secure before a cut may become unbalanced after a cut is

completed. An unbalanced load may tip the saw or anything

the saw is attached to, such as a table or workbench.

When making a cut that may become unbalanced, properly

support the workpiece and ensure the saw is firmly bolted

to a stable surface. Personal injury may occur.

WARNING: The clamp foot must remain clamped above

the base of the saw whenever the clamp is used. Always

clamp the workpiece to the base of the saw–not to any other

part of the work area. Ensure the clamp foot is not clamped

on the edge of the base of the saw.

CAUTION: Always use a work clamp to maintain control

and reduce the risk of workpiece damage and personal

injury.

If you cannot secure the workpiece on the table and against

the fence by hand, (irregular shape, etc.) or your hand would

be less than 6" (152 mm) from the blade, a clamp or other

fixture should be used.

For best results use the DW7082 clamp made for use with

your saw. It is available for purchase at your local retailer or

EWALT service center (Fig. 1).

Other aids such as spring clamps, bar clamps or C-clamps

may be appropriate for certain sizes and shapes of material.

Use care in selecting and placing these clamps. Take time

to make a dry run before making the cut. The left fence will

slide from side to side to aid in clamping.

TO INSTALL CLAMP (SOLD SEPARATELY)

1. Insert it into the hole behind the fence (Fig. 13). The

clamp should be facing toward the back of the miter

saw. The groove on the clamp rod should be fully

inserted into the base. Ensure this groove is fully inserted

into the base of the miter saw. If the groove is visible, the

clamp will not be secure.

2. Rotate the clamp 180º toward the front of the miter saw.

3. Loosen the knob to adjust the clamp up or down, then

use the fine adjust knob to firmly clamp the workpiece

(Fig 1).

NOTE: Place the clamp on the opposite side of the base

when beveling. ALWAYS MAKE DRY RUNS (UNPOWERED)

BEFORE FINISH CUTS TO CHECK THE PATH OF THE

BLADE. ENSURE THE CLAMP DOES NOT INTERFERE

WITH THE ACTION OF THE SAW OR GUARDS.

SUPPORT FOR LONG PIECES

WARNING: To reduce the risk of serious personal

injury, turn off the tool and disconnect it from the

power source before attempting to move it, change

accessories or make any adjustments.

ALWAYS SUPPORT LONG PIECES.

Never use another person as a substitute for a table

extension; as additional support for a workpiece that is

longer or wider than the basic miter saw table or to help

feed, support or pull the workpiece.

For best results, use the DW7080 extension work support

or the DWX723, DWX724 or DWX725B miter saw stand to

extend the table width of your saw. These are available from

your dealer at extra cost.

Support long workpieces using any convenient means such

as sawhorses or similar devices to keep the ends from

dropping.

CUTTING PICTURE FRAMES, SHADOW BOXES AND

OTHER FOUR-SIDED PROJECTS

To best understand how to make the items listed here, we

suggest that you try a few simple projects using scrap wood

until you develop a “FEEL” for your saw.

Your saw is the perfect tool for mitering corners like the one

shown in Figure 17. Sketch A in Figure 17 shows a joint

made by using the bevel adjustment to bevel the edges of

the two boards at 45° each to produce a 90° miter corner.

For this joint the miter arm was locked in the zero position

and the bevel adjustment was locked at 45°. The wood was

positioned with the broad flat side against the table and the

narrow edge against the fence. The cut could also be made

by mitering right and left with the broad surface against the

fence.

CUTTING TRIM MOLDING AND OTHER FRAMES

Sketch B in Figure 17 shows a joint made by setting the

miter arm at 45° to miter the two boards to form a 90°

corner. To make this type of joint, set the bevel adjustment

to zero and the miter arm to 45°. Once again, position the

wood with the broad flat side on the table and the narrow

edge against the fence.

The two sketches in Figure 17 are for four sided objects only.

As the number of sides changes, so do the miter and bevel

angles. The chart below gives the proper angles for a variety

of shapes. The chart assumes that all sides are of equal

length. For a shape that is not shown in the chart, use the

following formula. 180° divided by the number of sides

equals the miter or bevel angle.

- EXAMPLES -

NO. SIDES ANGLE MITER OR BEVEL

4 45°

5 36°

6 30°

7 25.7°

8 22.5°

9 20°

10 18°

CUTTING COMPOUND MITERS

A compound miter is a cut made using a miter angle and a

bevel angle at the same time. This is the type of cut used to

make frames or boxes with slanting sides like the one shown

in Figure 18.

NOTE: If the cutting angle varies from cut to cut, check that

the bevel clamp knob and the miter lock knob are securely

tightened. These knobs must be tightened after making any

changes in bevel or miter.

FIG. 21

FIG. 20

MITER

SCALE

FIG. 17

FIG. 18

FIG. 19

ANGLE « A »

English

The chart (Table 1) will assist you in selecting the proper

bevel and miter settings for common compound miter cuts.

To use the chart, select the desired angle “A” (Figure 19) of

your project and locate that angle on the appropriate arc in

the chart. From that point follow the chart straight down to

find the correct bevel angle and straight across to find the

correct miter angle.

Set your saw to the prescribed angles and make a few trial

cuts. Practice fitting the cut pieces together until you develop

a feel for this procedure and feel comfortable with it.

EXAMPLE: To make a 4 sided box with 26° exterior angles

(Angle A, Figure 19), use the upper right arc. Find 26° on

the arc scale. Follow the horizontal intersecting line to either

side to get miter angle setting on saw (42°). Likewise, follow

the vertical intersecting line to the top or bottom to get the

bevel angle setting on the saw (18°). Always try cuts on a

few scrap pieces of wood to verify settings on saw.

MITER SCALE (FIG. 20)

The scale is used when calculating angles. To calculate the

proper miter angle, divide 180° by the number of sides of the

box or frame. Refer to the chart for some examples.

VERNIER SCALE (FIG. 22, 23)

Your saw is equipped with a vernier scale for added

precision. The vernier scale allows you to accurately set

miter angles to the nearest 1/4°. To use the vernier scale

follow the steps listed below.

(As an example, let’s assume that the angle you want to

miter is 24-1/4° right).

1. Turn off miter saw.

2. Set the miter angle to the nearest whole degree desired

by aligning the center mark in the vernier scale, shown

in Figure 22, with the whole degree number etched in

the miter scale. Examine Figure 22 closely; the setting

shown is 24º right miter.

3. To set the additional 1/4°, squeeze the miter arm lock

and carefully move the arm to the RIGHT until the 1/4°

vernier mark aligns with the CLOSEST degree mark on

the miter scale. In our example, the closest degree mark

on the miter scale happens to be 25°. Figure 23 shows

a setting of 24-1/4° right miter.

For settings that require partial degrees (1/4, 1/2, 3/4°) align

the desired vernier mark with the CLOSEST degree mark

on the miter scale, as described above. (The plastic vernier

plate is inscribed with marks for 1/4, 1/2, 3/4 and 1°. Only

the 1/2° is numerically labeled.)

WHEN MITERING TO THE RIGHT

To increase the miter angle when mitering to the right, move

the arm to align the appropriate vernier mark with the closest

mark on the miter scale to the right. To decrease the miter

angle when mitering to the right, move the arm to align the

appropriate vernier mark with the closest mark on the miter

scale to the left.

FIG. 22

CENTER MARK ON VERNIER SCALE ALIGNS WITH

DESIRED WHOLE ANGLE ON MITER SCALE

(24° RIGHT MITER)

FIG. 23

1/4° VERNIER MARK ALIGNS WITH CLOSEST WHOLE DEGREE

MARK ON MITER SCALE (24-1/4° RIGHT MITER)

WHEN MITERING TO THE LEFT

To increase the miter angle when mitering to the left, move

the arm to align the appropriate vernier mark with the closest

mark on the miter scale to the left. To decrease the miter

angle when mitering to the left, move the arm to align the

appropriate vernier mark with the closest mark on the miter

scale to the right.

CUTTING BASE MOLDING

ALWAYS MAKE A DRY RUN WITHOUT POWER BEFORE

MAKING ANY CUTS.

Straight 90° cuts :

Position the wood against the fence as shown in

Figure 21. Turn on the saw, allow the blade to reach full

speed and lower the arm smoothly through the cut.

CUTTING BASE MOLDING UP TO 3.5" (88.9 mm)

HIGH VERTICALLY AGAINST THE FENCE

Position molding as shown in Figure 21.

All cuts are made with the back of the molding against the

fence and bottom of the molding against the base.

INSIDE CORNER: OUTSIDE CORNER:

Left side Left side

1. Miter left 45° 1. Miter right at 45°

2. Save left side of cut 2. Save left side of cut

Right side Right side

1. Miter Right 45° 1. Miter left at 45°

2. Save right side of cut 2. Save right side of cut

Material up to 3.5" (88.9 mm) can be cut as described

above. For wider boards [up to 4.25" (107.95 mm)] several

minor concessions must be made.

When cutting a board between 3.5" (88.9 mm) and 4.25"

(107.95 mm) in width the roller on the tip of the guard could

hang up on the workpiece. If this occurs, simply place your

right thumb on the upper side of the guard and roll the

guard up just enough to clear the workpiece, as shown in

Figure24. Once you have cleared the workpiece, you can

release the guard and it will continue to open as the cut

progresses.

When mitering to the right side of a base molding wider

than 3.5" (88.9 mm) standing vertically against the fence as

in Figure 21, the saw can only cut through the board up to

1 inch from the end of the board. Trying to cut more than

an inch will cause the saw’s gear case to interfere with the

workpiece. If you want to cut base molding between 3-1/2"

(88.9 mm) and 4.25" (107.95 mm) wide vertically follow the

directions below.

FIG. 24

English

CUTTING 3.5" (88.9 mm)– 4.25" (107.95 mm) BASE MOLDING VERTICALLY

AGAINST THE FENCE

• Position molding as shown in Figure 21.

• All cuts made with the back of the molding against the fence

INSIDE CORNER: OUTSIDE CORNER:

Left side Left side *

1. Position molding with bottom of

molding against the base of the saw

1. Position molding with bottom of

molding against the base of the saw

2. Miter left 45° 2. Miter right 45°

3. Save left side of cut 3. Save left side of cut

Right side Right side

1. Position molding with bottom of the

molding resting on the base of the

saw

1. Position molding with bottom of the

molding against the base of the saw

2. Miter right 45° 2. Miter left 45°

3. Save the right side of cut 3. Save the right side of cut

* NOTE: If the cut must be made somewhere other than 1" from the end of the

molding: cut off the molding at 90° approx. 1" (25.4 mm) longer than your final

length then make the miter cut as described above.

Another method of making the cut is to make a zero degree miter, 45° bevel cut. Your saw

can cut a bevel 6.2" (157.5 mm) wide.

CUTTING BASE MOLDING LAYING FLAT AND USING THE BEVEL FEATURE

• All cuts made with the saw set at 45° bevel and 0 miter.

• All cuts made with back of molding laying flat on the saw as shown in Figure 25.

FIG. 25

• Move the left side fence out of the path of the blade before attempting any of the following

cuts.

INSIDE CORNER: OUTSIDE CORNER:

Left side Left side

1. Position molding with top of molding

against the fence

1. Position molding with bottom of the

molding against the fence

2. Save left side of cut 2. Save right side of cut

Right side Right side

1. Position molding with bottom of the

molding against the fence

1. Position molding with top of molding

against the fence

2. Save left side of cut 2. Save right side of cut

CUTTING CROWN MOLDING

Your miter saw is better suited to the task of cutting crown molding than any tool made.

In order to fit properly, crown molding must be compound mitered with extreme accuracy.

The two flat surfaces on a given piece of crown molding are at angles that, when added

together, equal exactly 90°. Most, but not all, crown molding has a top rear angle (the section

that fits flat against the ceiling) of 52° and a bottom rear angle (the part that fits flat against

the wall) of 38°.

Your miter saw has special pre-set miter detent points at 31.62° left and right for cutting crown

molding at the proper angle (Fig. 26). There is also a mark on the Bevel scale at 33.85°.

The Bevel Setting/Type of Cut chart gives the proper settings for cutting crown molding.

(The numbers for the miter and bevel settings are very precise and are not easy to accurately

set on your saw.) Since most rooms do not have angles of precisely 90°, you will have to fine

tune your settings anyway.

FIG. 26

PRETESTING WITH SCRAP MATERIAL IS EX TREME LY IMPORTANT!

FOR CUTTING CROWN MOLDING LAYING

FLAT AND USING THE COMPOUND FEATURES

1. Move the left side fence out of the path of the blade before attempting any of the

following cuts.

2. Molding laying with broad back surface down flat on saw table (Fig. 26–27).

3. The settings below are for all Standard (U.S.) crown molding with 52° and 38° angles.

English

FENCE

FIG. 28

BLADE

FENCE

RIGHT

FIG. 27

FENCE

TABLE

CROWN MOLDING FLAT ON TABLE AND

AGAINST FENCE

CROWN MOLDING BETWEEN FENCE AND TABLE

TABLE

FENCE

BOTTOM SIDE

OF MOLDING

TOP SIDE

OF MOLDING

FIG. 29

DW7084 CROWN

MOLDING FENCE

FIG. 30

BLADE

WRONG

BEVEL SETTING TYPE OF CUT

33.85°

LEFT SIDE, INSIDE CORNER:

1. Top of molding against fence

2. Miter table set right 31.62°

3. Save left end of cut

33.85°

RIGHT SIDE, INSIDE CORNER:

1. Bottom of molding against fence

2. Miter table set left 31.62°

3. Save left end of cut

33.85°

LEFT SIDE, OUTSIDE CORNER:

1. Bottom of molding against fence

2. Miter table set left 31.62°

3. Save right end of cut

33.85°

RIGHT SIDE, OUTSIDE CORNER:

1. Top of molding against fence

2. Miter table set right 31.62°

3. Save right end of cut

When setting bevel and miter angles for all compound

miters, remember that:

The angles presented for crown moldings are very precise

and difficult to set exactly. Since they can easily shift

slightly and very few rooms have exactly square corners,

all settings should be tested on scrap molding.

PRETESTING WITH SCRAP MATERIAL IS

EXTREME LY IMPORTANT!

ALTERNATIVE METHOD FOR CUTTING CROWN

MOLDING

Place the molding on the table at an angle between the fence

and the saw table, as shown in Figure 29. Use of the crown

molding fence accessory (DW7084) is highly recommended

because of its degree of accuracy and convenience. The

crown molding fence accessory is available at extra cost from

your local dealer.

The advantage to cutting crown molding using this method

is that no bevel cut is required. Minute changes in the miter

angle can be made without affecting the bevel angle. This

way, when corners other than 90° are encountered, the saw

can be quickly and easily adjusted for them. Use the crown

molding fence accessory (DW7084) to maintain the angle at

which the molding will be on the wall.

INSTRUCTIONS FOR CUTTING CROWN MOLDING

ANGLED BETWEEN THE FENCE AND BASE OF

THE SAW FOR ALL CUTS

1. Angle the molding so the bottom of the molding (part

which goes against the wall when installed) is against the

fence and the top of the molding is resting on the base of

the saw, as shown in Figure 29.

2. The angled “flats” on the back of the molding must rest

squarely on the fence and base of the saw.

INSIDE CORNER: OUTSIDE CORNER:

Left side Left side

1. Miter right at 45° 1. Miter left at 45°

2. Save right side of cut 2. Save right side of cut

Right side Right side

1. Miter left at 45° 1. Miter right at 45°

2. Save left side of cut 2. Save left side of cut

Special Cuts

NEVER MAKE ANY CUT UNLESS THE MATERIAL IS

SECURED ON THE TABLE AND AGAINST THE FENCE.

ALUMINUM CUTTING

ALWAYS USE THE APPROPRIATE SAW BLADE MADE

ESPECIALLY FOR CUTTING ALUMINUM. These are available

at your local DEWALT retailer or DEWALT service center.

Certain workpieces, due to their size, shape or surface finish,

may require the use of a clamp or fixture to prevent movement

during the cut. Position the material so that you will be cutting

the thinnest cross section, as shown in Figure 28. Figure 30

illustrates the wrong way to cut these extrusions. Use a stick

wax cutting lubricant when cutting aluminum. Apply the stick

wax directly to the saw blade before cutting. Never apply stick

wax to a moving blade.

English

The wax, available at most hardware stores and industrial

mill supply houses, provides proper lubrication and keeps

chips from adhering to the blade.

Be sure to properly secure workpiece. Refer to Saw Blades

under Accessories for correct saw blade.

BOWED MATERIAL

When cutting bowed material always position it as shown in

Figure 31 and never like that shown in Figure 32. Positioning

the material incorrectly will cause it to pinch the blade near

the completion of the cut.

CUTTING PLASTIC PIPE OR OTHER ROUND

MATERIAL

Plastic pipe can be easily cut with your saw. It should be cut

just like wood and CLAMPED OR HELD FIRMLY TO THE

FENCE TO KEEP IT FROM ROLLING. This is extremely

important when making angle cuts.

CUTTING LARGE MATERIAL

Occasionally you will encounter a piece of wood a little too

large to fit beneath the blade guard. A little extra height can

be gained by rolling the guard up out of the way, as shown in

Figure 24. Avoid doing this as much as possible, but if need

be, the saw will operate properly and make the bigger cut.

NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD

OPEN WHEN OPERATING THIS SAW.

MAINTENANCE

DO NOT use lubricants or cleaners (particularly spray or

aerosol) in the vicinity of the plastic guard. The polycarbonate

material used in the guard is subject to attack by certain

chemicals.

1. All bearings are sealed. They are lubricated for life and

need no further maintenance.

FIG. 32

INCORRECT

FIG. 31

CORRECT

FENCE

2. Periodically clean all dust and wood chips from around

AND UNDER the base and the rotary table. Even though

slots are provided to allow debris to pass through, some

dust will accumulate.

3. The brushes are designed to give you several years of

use. To replace the brushes refer to Brushes on page 8

or return the tool to the nearest service center for repair.

A list of service center locations is packed with your tool.

Service Information

Please have the following information available for all service

calls:

Model Number _____________________________ Type ___

Serial Number ______________________________________

Date and Place of Purchase __________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs,

maintenance and adjustment should be performed by a

EWALT factory service center, a DEWALT authorized service

center or other qualified service personnel. Always use

identical replacement parts.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty

materials or workmanship for three years from the date of

purchase. This warranty does not cover part failure due to

normal wear or tool abuse. For further detail of warranty

coverage and warranty repair information, visit www.dewalt.

com or call 1-800-4-D

EWALT (1-800-433-9258). This

warranty does not apply to accessories or damage caused

where repairs have been made or attempted by others. This

warranty gives you specific legal rights and you may have

other rights which vary in certain states or provinces.

In addition to the warranty, D

EWALT tools are covered by our:

1 YEAR FREE SERVICE

EWALT will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your D

EWALT Power Tool, Laser, or Nailer for any reason,

you can return it within 90 days from the date of purchase

with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-D

EWALT

(1-800-433-9258) for a free replacement.

Please refer to the beginning of the manual for labels.

English

Troubleshooting Guide

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS

TROUBLE! WHAT’S WRONG? WHAT TO DO

Saw will not start 1. Saw not plugged in 1. Plug in saw.

2. Fuse blown or circuit breaker tripped 2. Replace fuse or reset circuit breaker.

3. Cord damaged 3. Have cord replaced by authorized service center.

4. Brushes worn out 4. Have brushes replaced by authorized service center or replace them yourself. Refer to Brushes.

Saw makes

unsatisfactory cuts

1. Dull blade 1. Replace blade. Refer to Changing or Installing a New Saw Blade.

2. Blade mounted backwards 2. Turn blade around. Refer to Changing or Installing a New Saw Blade.

3. Gum or pitch on blade 3. Remove blade and clean with turpentine and coarse steel wool or household oven cleaner.

4. Incorrect blade for work being done 4. Change the blade type. Refer to Saw Blades under Accessories.

Blade does not come

up to speed

1. Extension cord too light or too long 1. Replace with adequate size cord. Refer to Use Proper Extension Cord under Important Safety

Instructions.

2. Low house current 2. Contact your electric company.

Machine vibrates

excessively

1. Saw not mounted securely to stand

or work bench

1. Tighten all mounting hardware. Refer to Bench Mounting.

2. Stand or bench on uneven floor 2. Reposition on flat level surface. Refer to Familiarization.

3. Damaged saw blade 3. Replace blade. Refer to Changing or Installing a New Saw Blade.

Does not make accurate

miter cuts

1. Miter scale not adjusted correctly 1. Check and adjust. Refer to Miter Scale Adjustment under Adjustments.

2. Blade is not square to fence 2. Check and adjust. Refer to Miter Scale Adjustment under Adjustments.

3. Blade is not perpendicular to table 3. Check and adjust fence. Refer to Bevel Square to Table Adjustment under Adjustments.

4. Workpiece moving 4. Clamp workpiece securely to fence or glue 120 grit sandpaper to fence with rubber cement.

Material pinches blade 1. Cutting bowed material 1. Refer to Bowed Material under Special Cuts.

English

TABLE 1: COMPOUND MITER CUT

(POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE)

SET THIS MITER ANGLE ON SAW

ANGLE OF SIDE OF BOX (ANGLE A)

SQUARE BOX

6-SIDED BOX

SET THIS BEVEL ANGLE ON SAW

8-SIDED BOX

Français

Table des matières

DÉFINITIONS : LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ ..............................18

CONSIGNES DE SÉCURITÉ IMPORTANTES ...................................................................18

INSTRUCTIONS RELATIVES À LA DOUBLE ISOLATION

ET À LA FICHE POLARISÉE .............................................................................................18

DIRECTIVES DE SÉCURITÉ POUR TOUS LES OUTILS ...................................................18

RÈGLES DE SÉCURITÉ SUPPLÉMENTAIRES .................................................................19

CONNEXION ÉLECTRIQUE .............…………………………………………………………21

ACCESSOIRES ................................................................................................................. 21

ACCESSOIRES FACULTATIFS .....……………………………………………………………21

FICHE TECHNIQUE ...... ………………………………………………………………………22

DÉBALLAGE DE LA SCIE ............……………………………………………………………22

FAMILIARISATION ......... ………………………………………………………………………22

MONTAGE SUR ÉTABLI ...……………………………………………………………………23

CHANGEMENT OU POSE D’UNE LAME DE SCIE NEUVE .........…………………………23

TRANSPORT DE LA SCIE ...............…………………………………………………………23

RÉGLAGES ............... …………………………………………………………………………24

RÉGLAGE DE L’ÉCHELLE D’ONGLETS ...................................................................24

RÉGLAGE DU POINTEUR D’ONGLET ......................................................................24

RÉGLAGE DU BISEAU EN ÉQUERRE AVEC LA TABLE ...........................................24

POINTEUR DE BISEAU .............................................................................................24

BUTÉE DE BISEAU ...................................................................................................24

RÉGLAGE DU GUIDE ... …………………………………………………………………24

ACTIVATION ET VISIBILITÉ DU PARE-MAIN .............................................................25

FREIN ÉLECTRIQUE AUTOMATIQUE .......................................................................25

RÉGLAGE DU VERROUILLAGE DE L’ONGLET ........................................................26

BALAIS ..............………………………………………………………………………………26

FONCTIONNEMENT ......................................................................................................... 26

DÉTENTE ..................................................................................................................26

COUPE À L’AIDE DE VOTRE SCIE ...........................................................................26

COUPES TRANSVERSALES .......................................................................................26

COUPES EN BISEAU ..................................................................................................26

QUALITÉ DE COUPE ...................................................................................................26

POSITION DU CORPS ET DES MAINS ....................................................................... 26

FIXATION DE LA PIÈCE .............................................................................................27

INSTALLATION DE LA BRIDE ......................................................................................28

SOUTIEN DES PIÈCES LONGUES ...........................................................................28

DÉCOUPE DE CADRES, DE COFFRAGES

ET D’AUTRES OBJETS À QUATRE FACES ..............................................................28

COUPE DE MOULURES DE GARNISSAGE ET D’AUTRES CADRES ......................28

COUPE À ONGLETS MIXTES ...................................................................................28

ÉCHELLE À ONGLETS .............................................................................................29

ÉCHELLE À VERNIER .................................................................................................29

POUR L’ASSEMBLAGE EN ONGLET À DROITE ......................................................29

POUR L’ASSEMBLAGE EN ONGLET À GAUCHE ....................................................29

COUPE DE MOULURE D’EMBASE ..........................................................................29

COUPE DE MOULURE COURONNÉE ......................................................................30

COUPES SPÉCIALES .......................................................................................................32

ENTRETIEN.......................................................................................................................32

RÉPARATIONS ..................................................................................................................32

GARANTIE ........................................................................................................................32

GUIDE DE DÉPANNAGE ..................................................................................................33

TABLEAU DE RÉFÉRENCE POUR COUPE À ONGLETS MIXTES ...................................34

Français

Déﬁ nitions : Lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de gravité pour chaque symbole. Veuillez lire le

mode d’emploi et porter une attention particulière à ces symboles.

DANGER : Indique une situation dangereuse imminente qui, si elle n’est pas évitée,

causera la mort ou des blessures graves.

AVERTISSEMENT :

Indique une situation potentiellement dangereuse qui, si elle n’est pas

évitée, pourrait se solder par un décès ou des blessures graves.

ATTENTION : Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée

pourrait se solder par des blessures mineures ou modérées.

AVIS : Indique une pratique ne posant aucun risque de dommages corporels mais

qui par contre, si rien n’est fait pour l’éviter, pourrait poser des risques de dommages

matériels.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE SUR CET OUTIL OU SUR

TOUT AUTRE OUTIL DeWALT, COMPOSER LE NUMÉRO SANS FRAIS SUIVANT :

1-800-4-D

EWALT (1-800-433-9258).

CONSIGNES DE SÉCURITÉ IMPORTANTES

AVERTISSEMENT : Lire toutes les directives avant d’utiliser le produit.

Négliger de suivre toutes les directives suivantes peut entraîner des risques

de chocs électriques, d’incendie et/ou de blessures graves.

LIRE TOUTES CES DIRECTIVES

Double isolation

Afin de protéger l’utilisateur contre les décharges électriques, les outils à double isolation sont

complètement recouverts de deux couches distinctes d’isolant électrique ou d’une simple

épaisseur renforcée de matière isolante. Les outils comportant ce système d’isolation ne sont

pas conçus pour être mis à la terre. L’outil est donc doté d’une prise à deux broches qui

permet d’utiliser des rallonges sans avoir à se soucier de maintenir une connexion à la terre.

REMARQUE : le fait que cet outil soit muni d’une double isolation ne signifie pas que

l’utilisateur peut cesser de respecter les consignes de sécurité qui s’imposent. L’isolation

secondaire offre une protection contre tout dommage corporel pouvant résulter d’une

défaillance électrique possible du système primaire d’isolation interne.

ATTENTION : EN CAS DE RÉPARATION, UTILISER UNIQUEMENT DES PIÈCES DE

RECHANGE IDENTIQUES. Réparer ou remplacer les cordons d’alimentation endommagés.

Fiches polarisées

Certains appareils comportent des fiches polarisées (c’est-à-dire qu’une lame est plus large

que l’autre) afin de réduire le risque de choc électrique. Lorsqu’elle est présente, cette fiche

ne se branche que d’une seule façon dans une prise de courant polarisée. Si la fiche ne

s’insère pas totalement dans la prise de courant, l’inverser. Si elle ne s’insère toujours pas

dans la prise, demander à un électricien compétent d’installer une fiche polarisée. Ne pas

remplacer la fiche.

Consignes de sécurité pour tous les outils

AVERTISSEMENT : TOUJOURS utiliser une protection oculaire lors de l’utilisation

de la scie à onglets pour réduire le risque de blessures aux yeux.

• MAINTENIR LE PROTÈGE-LAME EN PLACE et en état de fonctionnement.

• RETIRER LES CLÉS À MOLETTE ET LES CLÉS DE RÉGLAGE. S’habituer à vérifier

si les clés à molette et les clés de réglage sont retirées de la broche avant de mettre l’outil

sous tension. Des outils, des déchets de découpe et d’autres débris peuvent être projetés

à grande vitesse, provoquant des blessures.

• GARDER LA ZONE DE TRAVAIL PROPRE. Les zones et établis encombrés sont

souvent des causes d’accidents.

• NE PAS UTILISER L’APPAREIL DANS UN ENVIRONNEMENT DANGEREUX.

L’utilisation d’outils électriques dans des endroits humides ou mouillés ou sous la pluie

peut provoquer un choc électrique ou une électrocution. Tenir la zone de travail bien

éclairée pour éviter de trébucher ou de mettre bras, mains et doigts en danger.

• TENIR LES ENFANTS À L’ÉCART. Tous les visiteurs doivent se trouver à une distance

sûre de la zone de travail. Un atelier représente un environnement potentiellement

dangereux.

• S’ASSURER QUE L’ATELIER NE PRÉSENTE PAS DE DANGER POUR LES

ENFANTS : utiliser des cadenas, des interrupteurs principaux ou retirer les clés de

démarrage. Le démarrage non autorisé d’un appareil par un enfant ou un visiteur pourrait

se solder par des blessures.

• NE PAS FORCER L’OUTIL. Le travail sera mieux accompli et sera moins dangereux au

rythme prévu pour l’appareil.

• UTILISER L’OUTIL APPROPRIÉ. Ne pas forcer un outil ou un accessoire pour effectuer

un travail auquel il n’a pas été conçu. L’utilisation d’un outil ou d’un accessoire inapproprié

pourrait se solder par des blessures corporelles.

• PORTER LES VÊTEMENTS APPROPRIÉS. Ne pas porter ni vêtement ample, ni gant,

ni cravate, ni bague, ni bracelet, ni autre bijou, car ces derniers pourraient s’enchevêtrer

dans des pièces mobiles. Des souliers antidérapants sont recommandés. Se couvrir

les cheveux s’ils sont longs. Se tenir éloigné des évents, car ces derniers pourraient

camoufler des pièces mobiles.

• TOUJOURS PORTER DES LUNETTES DE SÉCURITÉ. Les lunettes ordinaires

ne constituent PAS des lunettes de sécurité. Utiliser également un masque facial ou

antipoussière si l’opération de découpe génère de la poussière. TOUJOURS PORTER

UN ÉQUIPEMENT DE SÉCURITÉ HOMOLOGUÉ :

• protection oculaire conforme à la norme ANSI Z87.1 (CAN/CSA Z94.3);

• protection auditive conforme à la norme ANSI S12.6 (S3.19);

• protection des voies respiratoires conforme aux normes NIOSH/OSHA/MSHA.

• FIXER LA PIÈCE. Utiliser des brides de fixation ou un étau pour maintenir la pièce sur

la table et contre le guide. Faire de même lorsque le travail à effectuer exigera que la

main de l’opérateur se trouve très proche de la lame (à moins de 152 mm [6 po]). Une

telle pratique est plus sécuritaire, car l’opérateur peut utiliser ses deux mains pour faire

fonctionner l’outil.

• NE PAS TROP TENDRE LES BRAS. Conserver son équilibre en tout temps. Une perte

d’équilibre risque d’entraîner une blessure corporelle.

• PRENDRE SOIN DES OUTILS. S’assurer que les outils sont aiguisés et propres afin

d’optimiser sécurité et performance. Suivre les consignes de graissage et de changement

d’accessoires. Les machines et outils mal entretenus peuvent s’endommager davantage

et/ou provoquer des blessures.

• ÉTEINDRE L’APPAREIL ET COUPER LE COURANT avant d’installer ou de retirer

des accessoires, avant de réaliser ou de modifier un réglage et lors de réparations ou de

déplacements de l’appareil. Un démarrage accidentel peut provoquer des blessures. Ne

pas toucher aux lames métalliques de la fiche lors du branchement ou du débranchement

du cordon d’alimentation.

• RÉDUIRE LE RISQUE DE DÉMARRAGE ACCIDENTEL. S’assurer que l’interrupteur

se trouve sur la position « ARRÊT » avant de brancher le cordon d’alimentation.

• UTILISER UNE RALLONGE APPROPRIÉE. S’assurer que la rallonge est en bon état.

Si le produit est doté d’un cordon amovible, utiliser uniquement une rallonge à 3 fils

pourvue d’une fiche de mise à la terre à 3 lames et d’une prise à 3 fentes correspondant

à la fiche de l’outil. Lorsqu’une rallonge est utilisée, s’assurer d’utiliser un calibre

suffisamment élevé pour assurer le transport du courant nécessaire au fonctionnement de

l’appareil. Une rallonge de calibre inférieur causera une chute de tension de ligne et donc

une perte de puissance et une surchauffe. Le tableau suivant indique le calibre approprié

à utiliser selon la longueur de la rallonge et l’intensité nominale de la plaque signalétique.

La page charge ...

DeWalt DW713 Mode d'emploi

Marque: DeWalt

Modèle: DW713

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DW713 User guide
español: DeWalt DW713 Guía del usuario

Documents connexes

Autres documents

Ryobi TS230 Le manuel du propriétaire