Denon DHT-487DV Manuel utilisateur

Marque: Denon

Modèle: DHT-487DV

Catégorie: Lecteurs DVD

Taper: Manuel utilisateur

DVD-557

DVD VIDEO PLAYER

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 1

–

WARNING

: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Read Instructions - All the safety and operating instruc-

tions should be read before the product is operated.

2) Retain Instructions - The safety and operating instruc-

tions should be retained for future reference.

3) Heed Warnings - All warnings on the product and in

the operating instructions should be adhered to.

4) Follow Instructions - All operating and use instruc-

tions should be followed.

5) Cleaning - Unplug this product from the wall outlet

before cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

6) Attachments - Do not use attachments not recom-

mended

by the product manufacturer as they may cause

hazards.

7) Water and Moisture - Do not use this product near

water - for example, near a bath tub, wash bowl,

kitchen sink, or laundry tub; in a wet basement; or

near a swimming pool; and the like.

8) Accessories - Do not place this product on an unsta-

ble cart, stand, tripod, bracket, or table. The product

may fall, causing serious injury to a child or adult, and

serious damage to the product. Use only with a cart,

stand, tripod, bracket, or table recommended by the

manufacturer, or sold with the product. Any mounting

of the product should follow the manufacturer’s

instructions, and should use a mounting accessory

recommended by the manufacturer.

9) A product and cart combination

should be moved with care. Quick

stops, excessive force, and

uneven surfaces may cause the

product and cart combination to

overturn.

10)

Ventilation - Slots and openings in

the cabinet are provided for venti-

lation and to ensure reliable opera-

tion of the product and to protect it

from overheating, and these openings must not be

blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug, or

other similar surface. This product should not be placed

in a built-in installation such as a bookcase or rack

unless proper ventilation is provided or the manufactur-

er's instructions have been adhered to.

11)

Power Sources - This product should be operated only

from the type of power source indicated on the marking

label. If you are not sure of the type of power supply to

your home, consult your product dealer or local power

company. For products intended to operate from battery

power, or other sources, refer to the operating instructions.

12)

Grounding or Polarization - This product may be equipped

with a polarized alternating-current line plug (a plug hav-

ing one blade wider than the other). This plug will fit into

the power outlet only one way. This is a safety feature. If

you are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13)

Power-Cord Protection - Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the product.

14) Lightning - For added protection for this product dur-

ing a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the

wall outlet. This will prevent damage to the product

due to lightning and power-line surges.

15) Power lines - An outside antenna system should not

be located in the vicinity of overhead power lines or

other electric light or power circuits, or where it can

fall into such power lines or circuits. When installing

an outside antenna system, extreme care should be

taken to keep from touching such power lines or cir-

cuits as contact with them might be fatal.

16) Overloading - Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can

result in a risk of fire or electric shock.

17) Object and Liquid Entry - Never push objects of any

kind into this product through openings as they may

touch dangerous voltage points or short-out parts that

could result in a fire or electric shock. Never spill liq-

uid of any kind on the product.

18) Servicing - Do not attempt to service this product

yourself as opening or removing covers may expose

you to dangerous voltage or other hazards. Refer all

servicing to qualified service personnel.

19) Damage Requiring Service - Unplug this product from

the wall outlet and refer servicing to qualified service

personnel under the following conditions:

a) When the power-supply cord or plug is damaged.

b) If liquid has been spilled, or objects have fallen into

the product.

c) If the product has been exposed to rain or water.

d) If the product does not operate normally by follow-

ing the operating instructions. Adjust only those

controls that are covered by the operating instruc-

tions as an improper adjustment of other controls

may result in damage and will often require exten-

sive work by a qualified technician to restore the

product to its normal operation.

If the product has been dropped or damaged in any way.

f) When the product exhibits a distinct change in per-

formance - this indicates a need for service.

20)

Replacement Parts - When replacement parts are

required, be sure the service technician has used replace-

ment parts specified by the manufacturer or have the same

characteristics as the original part. Unauthorized substitu-

tions may result in fire, electric shock, or other hazards.

21) Safety Check - Upon completion of any service or

repairs to this product, ask the service technician to

perform safety checks to determine that the product

is in proper operating condition.

22)

Heat - The product should be situated away from heat

sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

PORTABLE CART WARNING

(Symbol provided by RETAC)

S3125A

IMPORTANT SAFEGUARDS

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 2

–

English

PRECAUTIONS

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible

eye injury.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECI-

FIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO

BEAM.

LOCATION: INSIDE, NEAR THE DECK MECHANISM.

Laser Safety

RADIO-TV INTERFERENCE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to

this equipment may cause harmful interference unless the modifications are expressly approved in the

instruction manual. The user could lose the authority to operate this equipment if an unauthorized change

or modification is made.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Non-use periods - Turn off the unit when it is not in use. Unplug the unit from the household AC outlet if it is

not to be used for a long time. Unplug the unit during lightning storms.

Please read this operating instructions carefully before using your DVD player, and keep it for future reference.

Important

The main power supply is engaged when the main plug is

plugged in a 120V, 60Hz AC outlet. To operate the unit, press

the ON/STANDBY button to turn on the unit.

Power Supply

Use only discs marked with logos listed on page 6.

To avoid fire or electric shock, do not expose this unit to rain

or moisture.

WARNING:

LIVE PARTS INSIDE.

DO NOT REMOVE ANY SCREWS.

Warning

Installation Location

For safety and optimum performance of this unit:

•

Do not stand the unit up vertically. Install the unit in a hori-

zontal and stable position. Do not place anything directly on

top of the unit. Do not place the unit directly on top of the TV.

•

Shield it from direct sunlight and keep it away from sources

of intense heat. Avoid dusty or humid places. Avoid places

with insufficient ventilation for proper heat dissipation. Do not

block the ventilation holes on the sides of the unit. Avoid

locations subject to strong vibration or strong magnetic fields.

• Be sure to remove a disc and unplug the AC power cord

from the outlet before carrying the unit.

Cautions on Installation

Noise or disturbance of the picture may be generated if this

unit or any other electronic equipment using microproces-

sors is used near a tuner or TV.

If this happens, take the following steps:

• Install this unit as far as possible from the tuner or TV.

• Set the antenna wires from the tuner or TV away from this

unit’s power cord and input/output connection cords.

•

Noise or disturbance tends to occur particularly when using

indoor antennas or 300Ω/ohms feeder wires. We recommend

using outdoor antennas and 75Ω/ohms coaxial cables.

NOTE:

• For heat dispersal, do not install this equipment in a con-

fined space such as a book case or similar unit.

Wall

10cm or more

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 3

–

TABLE OF CONTENTS

■

IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . 2

■

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Important . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cautions on Installation . . . . . . . . . . . . . . . . . . . . . . . . . 3

Dew Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Avoid the Hazards of Electrical Shock and Fire . . . . . . . 4

Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

■

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

About Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Notice for the Progressive Scan Outputs . . . . . . . . . . . . 5

Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Symbols Used in this Manual. . . . . . . . . . . . . . . . . . . . . 5

■

ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

■

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

■

FUNCTIONAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . 8

FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . 8

Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . . 9

Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Displays During Operation . . . . . . . . . . . . . . . . . . . . . . 10

HDMI Mode and Actual Output Signals . . . . . . . . . . . . 10

Loading the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . 10

■

CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Description - Rear Panel . . . . . . . . . . . . . . . . . . . . . . . 11

Connection to an Audio System . . . . . . . . . . . . . . . . . . 12

Connection to a TV (for video) . . . . . . . . . . . . . . . . . . . 13

Connection to a TV with an HDMI compatible port . . . . 14

■

DISC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

HDMI Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Brightness of the Front Panel Display. . . . . . . . . . . . . . 15

General Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Disc Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

CALLING UP A MENU SCREEN DURING

PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Still / Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Resume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Fast Forward / Reverse Search . . . . . . . . . . . . . . . . . . 16

Slow Forward / Slow Reverse . . . . . . . . . . . . . . . . . . . 16

Step by Step Playback. . . . . . . . . . . . . . . . . . . . . . . . . 16

Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Title / Chapter Search . . . . . . . . . . . . . . . . . . . . . . . . . 16

By using the SEARCH MODE button . . . . . . . . . . . . 16

By using the SKIP buttons HG . . . . . . . . . . . . 16

Track Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

By using the SEARCH MODE button . . . . . . . . . . . . 17

By using the SKIP buttons HG . . . . . . . . . . . . 17

Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Marker Setup Screen. . . . . . . . . . . . . . . . . . . . . . . . . . 17

Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

REPEAT TITLE / CHAPTER. . . . . . . . . . . . . . . . . . . 17

REPEAT TRACK / GROUP / ALL . . . . . . . . . . . . . . . 17

A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Program Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

MP3 / JPEG / WMA Playback . . . . . . . . . . . . . . . . . . . 18

Changing the On-Screen Display . . . . . . . . . . . . . . . . . 20

Slide Show Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Dialog Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Subtitle Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Picture Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Stereo Sound Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Virtual Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Black Level Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

■

DVD SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Display Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Audio Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Ratings Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

RATING LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

IF YOU FORGET THE PASSWORD . . . . . . . . . . . . . 24

CONTROL LEVELS . . . . . . . . . . . . . . . . . . . . . . . . . 24

Others Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Reset to the Default settings

(except for Ratings Control) . . . . . . . . . . . . . . . . . . . . 25

Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . 25

■

TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . 26

■

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

■

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

PRECAUTIONS

Caution

1) Do not attempt to open the cabinet. There are no parts

you can service inside. Refer all servicing to qualified ser-

vice personnel.

Slot and openings in the cabinet and at the side or bottom

are provided for ventilation. To ensure reliable operation

and to protect the unit from overheating these opening

must not be blocked or covered. Avoid enclosed spaces

such as book cases unless proper ventilation is provided.

3) Keep the unit away from the radiator heat sources.

4) Avoid using near strong magnetic fields.

5) Do not push objects of any kind into this through the cabi-

net slot as they could touch current carrying parts or

short circuit parts resulting in a fire or electric shock.

6) Never spill liquid of any kind on this unit.

If liquid is spilled into the unit, consult qualified service

engineer.

7) Use this unit in a horizontal (flat) position only.

8) This equipment is in Stand-by mode when it turns off

whilst the power cord is connected.

9) Keep the set free from moisture, water and dust.

10) Handle the power cord carefully. Hold the plug when

unplugging the code.

11) All the safety cautions and operating instructions should

be read before the DVD player is operated.

12) Use caution not to pinch your finger in the disc slot.

13) Do not put heavy objects on the AC power cord.

14) Keep the AC power cord away from heat appliances.

15) Be sure to remove a disc and unplug the AC power cord

from the outlet before carrying the DVD player.

16) Do not put any pressure to the DVD player when carrying.

17) Do not use the DVD player outdoors.

Avoid the Hazards of Electrical Shock and Fire

• Do not handle the power cord with wet hands.

• Do not pull on the power cord when disconnecting it from

AC wall outlet. Grasp it by the plug.

• If, by accident, water is spilled on this unit, unplug the

power cord immediately and take the unit to our Authorized

Service Center for servicing.

Moisture condensation may occur inside the unit when it is

moved from a cold place to a warm place, or after heating a

cold room or under conditions of high humidity. Do not use the

DVD Player at least for 2 hours until its inside is dry.

Dew Warning

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 4

–

English

The serial number of this product may be found on the back of the DVD player. No others have the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectu-

al property rights. Use of this copyright protection technology must be authorized by Macrovision, and is

intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse

engineering or disassembly is prohibited.

INTRODUCTION

Supplied Accessories

About Copyright

Symbols Used in this Manual

The following symbols appear below in some headings and notes in this manual, with the following meanings.

:Description refers to playback of DVD-Video discs. (including DVD-R/RW discs)

:Description refers to playback of Audio CDs.

:Description refers to playback of discs formatted with MP3.

:Description refers to viewing of JPEG discs.

:Description refers to playback of discs formatted with WMA.

WMA

JPEG

MP3

DVD

RC-1018

“AA” (R6P)

batteries

• • • •

Operating

Instructions

• •

Service Station

List

• • • • • • • • •

Warranty

Card

• • • • • • • •

Audio

cable

• • • • • • •

Video

cable

• • • • • • • •

Remote

control

• • • • • •

Please check to make sure the following items are included with the main unit in the carton.

U. S. Patent Nos, 4,631,603, 4,819,098, 4,907,093, 5,315,448 and 6,516,132.

Notice for the Progressive Scan Outputs

Consumers should note that not all high definition television sets are fully compatible with this product and may

cause artifacts to be displayed in the picture. In case of picture problems with 525 progressive scan output, it is

recommended that the user switch the connection to the ‘standard definition’ output. If there are questions

regarding your TV set compatibility with this 525p DVD player, please contact our customer service center.

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your

local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning

chemical wastes.

Make your contribution to the environment!!!

• Used up batteries do not belong in the dust bin.

• You can dispose of them at a collection point for used up batteries or special waste. Contact your council for details.

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 5

–

ABOUT THE DISCS

Playable Discs

DVD-Video

* 1, 2, 3, 5

* 1, 3, 4, 5,

6, 7, 8

* 3, 5

* 3, 4, 5, 7, 8

DVD-R

DVD-RW

Audio CD

CD-R

CD-RW

Digital video

(MPEG2)

Region code

Mark (logo)

Playable

discs

Recorded

signals

Disc size

Disc types

12 cm

8 cm

Example

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1

Chapter 2

Chapter 3 Chapter 4

12 cm

8 cm

Digital audio

MP3

WMA

Digital picture

(JPEG)

Example

Group 1 Group 2

Tr ack 1

Tr ack 2 Track 5

Tr ack 6

Tr ack 3

Tr ack 4

Example

Tr ack 1

Tr ack 2

Tr ack 5

Tr ack 6

Tr ack 3 Track 4

Audio CD

Picture CD

12 cmJPEG

MP3,

JPEG,

WMA

is a trademark of DVD Format/Logo Licensing Corporation.

is trademark of Eastman Kodak Company.

Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries.

If you cannot play back a disc which bears one of the marks above, check the following notes.

*1: This player conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot

be played back.

*2:

Certain DVD discs do not operate as described in this manual due to the intentions of the disc’s producers.

*3: Scratched or stained discs may not be played back.

*4: Some discs cannot be played back because of incompatible recording conditions, characteristics of the

recorder or special properties of discs.

*5: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not

play them back. Even if they are played back, the sound or video quality will be compromised.

*6: Only the discs recorded in the video format and finalized can be played back.

Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be

played back at all or normally (the picture or sound may be distorted, etc.).

*7: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may not

play back properly.

*8:

Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it correctly.

*9: This player cannot play the disc contents protected by Windows Media Digital Rights Management (DRM).

¡ NEVER play back the following discs. Otherwise, malfunction may result!

DVD-RAM / CD-i / Photo CD / Video CD / DVD with region codes other than 1 or ALL /

DVD-ROM for personal computers / CD-ROM for personal computers

¡ On the following disc, the sound MAY NOT be heard.

Super Audio CD / DVD-Audio

NOTES:

• Only the sound recorded on the normal CD layer can be delivered. (Super Audio CD)

• The sound recorded on the high density Super Audio CD layer cannot be delivered. (Super Audio CD)

• Disc with the Video zone can be played. (DVD-Audio)

• Disc only of the Audio zone cannot be played. (DVD-Audio)

¡ Any other discs without compatibility indications

CAUTION:

• Use caution not to pinch your finger in the disc slot.

• Be sure to remove a disc and unplug the AC power cord from the outlet before carrying the DVD player.

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 6

–

English

FEATURES

¡Progressive Scan system

Unlike conventional interlace scanning, the progressive

scan system provides less flickering and images in

higher resolution than that of traditional (525i/480i)

television signals.

¡Dolby Digital Sound

By hooking up this player to a Multi-Channel Dolby

Digital decoder, you can enjoy high-quality Dolby

Digital Multi-channels surround sound as heard in the

movie theaters.

¡DTS (Digital Theater System)

When this player is connected to the DTS decoder, you

can enjoy Multi-channel surround system which repro-

duces the original sound as truthfully as possible. Multi-

channel surround system is developed by the Digital

Theater Systems, Inc.

¡HDMI (High Definition Multimedia Interface)

You can enjoy clearer video output when connecting

this player to a display equipment with an HDMI-com-

patible port.

¡Dialog Speed

Playback in slightly faster or slower speed while keep-

ing the sound quality as in the normal playback.

Dialog speed is available only on discs recorded in the

Dolby Digital format.

¡Still/Fast/Slow/Step playback

Various playback modes are available including still

pictures, fast forward/reverse, slow motion and step

frames.

¡Still Mode

The resolution of pictures while in the still (pause)

mode can be adjusted.

¡Random Playback for Audio CD, MP3, JPEG and

WMA

This player can shuffle the playback order of tracks in

random order.

¡Program Playback for Audio CD, MP3, JPEG and

WMA

You can program the playback order of tracks in a

desired order.

¡DVD menus in a desired language

You can display DVD menus in a desired language, if

available on a DVD.

¡Auto Power Off

The power turns off automatically if there is no activity

at the player or its remote for more than 30 minutes

(refer to page 25).

¡Subtitles in a desired language

You can select a desired language for subtitles if that

language is available on a disc.

¡Selecting a camera angle

You can select a desired camera angle if a disc con-

tains sequences recorded from different angles.

¡Choices for audio language and sound mode

You can select a desired audio language and sound

mode if different languages and modes are available

on a disc.

¡Ratings Control

You can set the control level to limit playback of discs

which may not be suitable for children.

¡Automatic detection of discs

This player automatically detects if a loaded disc is

DVD-Video, Audio CD, MP3, JPEG or WMA.

¡Playing back an MP3 disc

You can enjoy MP3 files which are recorded on CD-

R/RW.

¡Direct Search

You can search the desired title, chapter, and track with

numeric button during playback or in stop mode.

¡On-screen display

Information about the current operation can be dis-

played on a TV screen, allowing you to confirm the cur-

rently active functions (such as program playback)

using the remote control.

¡Dimmer

The brightness of the display can be adjusted.

¡Screen Saver

The screen saver program starts if there is no activity

at the player or its remote for more than 5 minutes. The

brightness of the display is darken by 75%. The pro-

gram is inactivated when there is any activity.

¡Picture Control

Picture Control adjusts Brightness, Contrast, Color,

Gamma Correction and Sharpness of the specific dis-

play.

¡Search

Chapter search: Search for a desired chapter.

Title search: Search for a desired title.

Track search: Search for a desired track.

Time search: Search for a desired time point or a

title or a track.

¡Repeat

Chapter: Repeated playback of a chapter of the

disc.

Title: Repeated playback of a title of the

disc.

Track: Repeated playback of a track of the

disc.

All: Repeated playback of the entire disc.

(exclude DVD)

A-B: Repeated playback of a part between

two points.

Group: Repeated playback of a folder of the

MP3/JPEG/WMA disc being played is

possible.

¡Zoom

2-time or 4-time magnified screen can be displayed.

¡Marker

Electric reference points designated by user can be

called back.

¡Resume Playback

User can resume playback from the point at which the

playback has been stopped even if the power is turned

off.

¡Component Video Out Jacks

Jacks located on the back of the DVD Player which are

used to send high-quality video to a TV via Component

Video In Jacks.

¡Bit rate indication

¡DRC (Dynamic Range Control)

You can control the range of sound volume.

¡Displaying a JPEG picture

Kodak Picture CDs can be played back. Still images

stored in JPEG format on CD-R/RW can also be

played back.

¡Reproducing WMA data

You can enjoy WMA files which are recorded on CD-

R/RW.

“WMA” (Windows Media Audio) is an audio

codec developed by Microsoft

in the United

States of America.

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 7

–

FUNCTIONAL OVERVIEW

FRONT PANEL

REMOTE CONTROL

The buttons with circled numbers can only be

operated with the remote control.

6/24

7/25

RC-1018

1. ON/STANDBY (POWER ON/OFF) Buttons [page 15]

2. Disc loading tray

3. OPEN/CLOSE Button [page 15]

4. PLAY Button [page 15]

5. STOP Button [page 15]

6. H (SKIP) Button [page 16]

7. G (SKIP) Button [page 16]

8. DIMMER Button [page 15]

9. REPEAT Button [page 17]

10. HDMI Button [page 15]

Press to set the HDMI connector’s video signal output

mode.

11. STILL/PAUSE Button [page 15]

12. Display, Remote Sensor Window

13. HDMI indicator [page 15]

Lights up when there is video signal output from the

HDMI OUT jack.

14. A-B REPEAT Button [page 18]

15. RANDOM Button [page 18]

16. ZOOM Button [page 16]

17. CLEAR Button [page 17]

18. ANGLE Button [page 22]

19. MENU Button [page 15]

20. ENTER Button [page 15]

21. Cursor Buttons [page 15]

22. RETURN Button [page 17]

23. SEARCH MODE Button [page 16]

24. h (Fast Reverse SEARCH) Button [page 16]

Press more than 2 seconds when you use the front

panel button for this function.

25. g (Fast Forward SEARCH) Button [page 16]

Press more than 2 seconds when you use the front

panel button for this function.

26. SETUP Button [page 23]

27. SUBTITLE Button [page 21]

28. TOP MENU Button [page 15]

29. DISPLAY Button [page 20]

30. AUDIO Button [page 21]

31. Numeric Buttons [page 15]

32. MODE Button [page 18]

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 8

–

English

Buttons on remote control work in different ways for DVD, Audio CD, MP3, JPEG and WMA:

Refer to the following table for correct use.

Tour of the Remote Control

FUNCTIONAL OVERVIEW

POWER Buttons

A-B REPEAT Button

REPEAT Button

MODE Button

SUBTITLE Button

DVD

To switch the power between on and standby.

To mark a segment between A and B for repeated

playback.

To mark a segment between A and B for repeated

playback. (CD)

To repeat playback of a title or chapter.

To repeat playback of a track or disc. (CD)

To repeat playback of a track, group or

disc. (MP3, JPEG, WMA)

RANDOM Button

To play back tracks in random order.

ZOOM Button

To program a specific playback order.

To activate the 3D sound (Virtual surround system).

(CD, MP3, WMA)

To magnify part of the picture (x2/x4).

ANGLE Button

To access various camera angles on the disc.

To access various subtitles on the disc.

AUDIO Button

DISPLAY Button

To access various audio functions on the disc.

To select STEREO, L-ch or R-ch. (CD)

To display the current disc or HDMI mode.

To search for a chapter, title, time or marker.

To return to a location on the disc rapidly.

OPEN/CLOSE Button

To search for a track.

To search for time or a marker. (CD)

To return to a location on the disc rapidly.

SEARCH MODE Button

Numeric Buttons

CLEAR Button

To open or close the disc tray.

To select a chapter or title directly.

To select a track directly.

To clear the markers.

To clear the numbers entered incorrectly.

To cancel the A point for A-B Repeat.

To clear the markers. (CD)

To clear the numbers entered incorrectly.

To cancel the A point for A-B Repeat. (CD)

CD/MP3/JPEG/WMA

To magnify part of the picture (x2). (JPEG)

To rotate a picture. (JPEG)

MENU Button

TOP MENU Button

ENTER, Cursor Buttons

RETURN Button

SEARCH Buttons

To call up the menu on a disc.

To call up the top menu on a disc.

To move the cursor and determine its position.

SETUP Button

To return to the previous operation in the setup

menu.

To return to the previous operation in the setup

menu.

To call up the setup menu. To call up the setup menu.

SKIP Buttons

To skip chapters/titles.

To begin fast forward/reverse search or slow forward/

slow reverse.

STOP Button

PLAY Button

To stop playback.

To begin playback.

To stop playback.

To begin playback.

STILL/PAUSE Button

To move the cursor and determine its position.

To skip tracks.

To pause playback.

To advance playback frame by frame.

To pause playback.

To call up the FILE LIST. (MP3, JPEG, WMA)

To return to the first item in the highest hierarchy

of the FILE LIST. (MP3, JPEG, WMA)

To begin fast forward/reverse search.

(CD, MP3, WMA)

To set Picture Control.

To set Black Level on/off.

To activate the 3D sound (Virtual surround system).

To set Dialog Speed.

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 9

–

Loading the Batteries

Front Panel Display

Displays During Operation

FUNCTIONAL OVERVIEW

1. Open the battery compartment cover.

2. Insert two “AA” (R6P) batteries, with each

one oriented correctly.

3. Close the cover.

The present display state is shown.

• TL./GR.: Title

• TR./CP.: Track or Chapter

To change to the display of a title please push

the DISPLAY button in the state of Resume.

Lights up when the inserted disc is being play back.

Displays the chapter (title) or track

number. In case the chapter (title) or

track number is over 100, displays

“_ _”.

Displays the elapsed time of the chapter (title) or track.

(The display of 10 hours or more cannot be performed.)

Selected HDMI output mode is displayed.

Lights up when playing back in slow mode. (DVD)

Lights up when the disc playback comes to a pause.

Lights up when the progressive scan system is activated. Displays a type of the disc which is on the tray.

• DVD: DVD

• CD: Audio CD, MP3, JPEG, WMA

Lights up when you have selected the

audio file such as CD and MP3, WMA

on the program screen.

Lights up when the repeat function is on.

Lights up when the ALL repeat function is on.

Lights up when the A-B repeat function is on.

Power on

No disc inserted or

cannot read

HDMI output mode

(480p) is selected

Tray open

Tray closed

Loading the Disc

Power off

HDMI output mode

(720p) is selected

HDMI output mode

(1080i) is selected

HDMI output mode

(OFF) is selected

Program playback is

set

Program playback setting

group (folder) is selected

Program playback setting

ALL CLEAR is selected

Random playback is

set

Cautions On Batteries

•

Use “AA” (R6P) batteries in this remote control unit.

• Replace the batteries with new ones approximate-

ly once a year, though this depends on the fre-

quency with which the remote control unit is used.

•

If the remote control unit does not operate within a

close proximity of the main unit, replace the batteries

with new ones, even if less than a year has passed.

•

The included batteries serve only for verifying operation.

Replace them with new batteries as soon as possible.

•

When inserting the batteries, be careful to do so in

the proper direction, following the and marks

in the remote control unit’s battery compartment.

• To prevent damage or battery fluid leakage:

• Do not mix a new battery with an old one.

• Do not mix two different types of batteries such

as alkaline and manganese.

• Do not short-circuit, disassemble, heat or dis-

pose of batteries in flames.

• Remove the batteries when not planning to use

the remote control unit for a long period of time.

•

If the batteries should leak, carefully wipe off the fluid from the

inside of the battery compartment, then insert new batteries.

HDMI Mode and Actual Output Signals

OFF

480p 1080i

1080i

1080i1080i

480p

480p 720p

720p

720p720p

480p

720p

1080i

480p

1080i

480p

720p

480p

480p 480p 480p

OFF

HDMI mode of this unit

Supported

HDMI format of

Display device

NOTES:

• The front panel display has blinked while setting the

program playback.

• “P**-●●●” is displayed in the front panel display while

setting the program playback. (“**” is program number,

“●●●”is track number.)

• “A” is displayed in front panel display while selecting the

audio file (CD, MP3, WMA).

• “F-***” is displayed in the front panel display while selecting

the group (folder). (“***” is group (folder) number.)

• “A-CLEAr” is displayed in the front panel display while

selecting ALL CLEAR.

• “SHUFFLE” is displayed in the front panel display while

setting the random playback.

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 10

–

English

CONNECTIONS

1. DIGITAL OUT Jacks (OPTICAL/COAXIAL)

Use either an optical or coaxial digital cable (commercially available) to connect to an AV amplifier with a built-in

decoder (AV control center).

2. AUDIO OUT Jacks

Use an audio cable to connect to the Audio input jacks of A/V-compatible TV, wide screen TV or Stereo system.

3. HDMI OUT Jack

Use a HDMI connection cable (commercially available) to connect to a display with an HDMI compatible port.

4. VIDEO OUT Jack

Use a video cable to connect one of the jacks to Video input on your A/V-compatible TV, wide screen TV or Stereo sys-

tem.

5. COMPONENT VIDEO OUT Jacks

Use a component video cable (commercially available) to connect these jacks if you have a TV with Component Video in

jacks. These jacks provide C

and Y video. Along with S-Video, Component Video provides the best picture

quality.

6. S-VIDEO OUT Jack

Use an S-Video cable (commercially available) to connect this jack to the S-Video jack on your A/V-compatible TV or

wide screen TV for a higher quality picture.

NOTE:

• When there is video output from the HDMI OUT jack, no signal is output from the COMPONENT VIDEO OUT jacks.

Selecting Progressive Scan (525p/480p or Interlaced 525i/480i) Playback

¡If your TV is compatible with progressive scanning (525p/480p), connect the TV to the COMPONENT VIDEO OUT jacks of

the DVD player and set PROGRESSIVE to ON in the Display setting. Next, set your TV to the progressive scan mode.

Refer to page 23 for instructions on changing the Display setting. P.SCAN will appear on the Display of the unit.

¡If your TV is not compatible with progressive scanning, set PROGRESSIVE to OFF (refer to page 23). Make sure that P.SCAN

on the display of the unit lights off.

¡Use a commercially available adaptor if the video input jacks of your TV or monitor is the BNC type.

¡The unit is sending Progressive video signal and HDMI signal simultaneously when HDMI mode is set to ON. If you con-

nected component video cable to your TV, which is not compatible with progressive scan, the distorted picture will be out-

put.

What is Progressive Scanning?

¡Unlike conventional interlace scanning, the progressive scan system provides less flickering and images in higher resolution

than that of traditional (525i/480i) television signals.

Description - Rear Panel

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks

of Dolby Laboratories.

1 32 4 5 6

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 11

–

Connection to an Audio System

Stereo system

NOTES (for Method 2 only):

• When using an AV amplifier with a built in decoder (AV control center), Dolby Digital, or DTS decoder as shown in the

Method 2, set “DOLBY DIGITAL” or “DTS” to “BITSTREAM” accordingly for audio output in the setup mode (refer to page

24). Set it to “PCM” or “OFF” for the decoder that is not used currently. Playing back a DVD using incorrect settings may

generate noise distortion, and may also damage the speakers.

• The audio source on a disc in a Dolby Digital

Multi-channel

surround format cannot be recorded as digital sound by an MD

deck or DAT deck.

•

Set “DOLBY DIGITAL” to “PCM” and “DTS” to “OFF” for audio output in the setup mode for connecting to an MD deck or DAT

deck (

refer to page 24)

•

Harsh noise that could harm your ears or the speakers is generated when a DVD recorded in DTS is played while using a

decoder, etc., that is not DTS-compatible.

•

When playing a copyright-protected 96kHz PCM DVD, the digital sound will be down sampled at 48kHz, even if you set “LPCM

SELECT” to “OFF” (refer to page 24).

AUDIO

DVD

Audio Input Jacks

Digital Audio Input

Jacks

AUDIO OUT

(analog)

DIGITAL OUT

• Method 1 DVD Player + Stereo system

• Method 2 DVD Player + AV amplifier with a built in decoder (AV control center), Dolby Digital decoder, DTS decoder,

MD deck or DAT deck

Method 1 Method 2

CONNECTIONS

The following shows examples of connections commonly used to connect the DVD player to TV and other

components.

If using this DVD player to play back a DVD in a Dolby Digital Multi-channel surround or DTS surround format, the

DVD player outputs a Dolby Digital or DTS data stream from its OPTICAL or COAXIAL DIGITAL OUT jacks.

By hooking up the player to a Dolby Digital or DTS decoder, you can enjoy more convincing, realistic ambience

with powerful and high-quality surrounding sound of a professional standard which can be heard in movie theaters.

Use a commercially available audio optical or coaxial digital cable (not included) for the audio connections.

NOTES:

• Be sure to turn off the power of all components in the system before connecting another component.

• Refer to the Instruction Manuals for your TV, stereo system and any other components to be connected to the

DVD player.

Optical cable (commercially available)

• Optical cable (commercially available) may be damaged when bent at sharp angles. Ensure cables are coiled in loops with

a diameter of 6 inches (15cm) or more when storing them.

• Use a cable which is 9.8 feet (3m) or shorter.

• Insert cable plugs firmly into the connectors when making connections.

• If a plug has dust or is dirty, clean it with a soft cloth before inserting it into a connector.

AV amplifier with a built in decoder

(AV control center),

Dolby Digital decoder,

DTS decoder,

MD deck or DAT deck

Optical cable

(commercially

available)

Audio Coaxial

Digital cable

(commercially

available)

Audio cable

(supplied)

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 12

–

English

NOTES:

• Connect the DVD player directly to a TV. If the Audio/Video cables are connected to a VCR, pictures may be distorted due

to the copy protection system.

• S-Video output connector

The video signals are divided into color (C) and brightness (Y) signals, achieving a clearer picture.

If the TV is equipped with a S-Video input connector, we recommend connecting it to this unit’s S-Video output connector

using a commercially available S-Video connection cord.

• Component output connector

Picture could be distorted if you connect DVD player with both Component output connector and HDMI output connector at

the same time.

HOW TO CONNECT TO A TV WITHOUT AUDIO/VIDEO INPUT JACKS

If your TV does not have RCA type audio and video input jacks it is still possible to connect this DVD

player to your TV’s 75-ohm coaxial antenna terminal using an optional Stereo Audio/Video RF Modulator, not includ-

ed. Connect the audio and video outputs of the DVD player to the audio and video inputs on the RF Modulator, and

then connect the coaxial output of the RF Modulator (usually marked “TO TV”) to the 75 ohm coaxial antenna termi-

nal on your TV. Follow the instruction supplied with the RF Modulator for more details.

If your TV’s 75 ohm coaxial antenna terminal is already occupied by an antenna or cable box connection, remove that

cable from your TV’s antenna terminal and reconnect it to the coaxial antenna input terminal of the RF Modulator

(usually marked “ANT IN”), then connect the RF modulator to your TV’s antenna terminal as described above.

NOTE:

• The picture quality from DVD discs will not be as good if the DVD player is connected to the TV’s antenna terminal

through an RF Modulator.

CONNECTIONS

Connection to a TV (for video)

DVD

S-VIDEO IN

VIDEO IN

CB/PBYCR/PR

COMPONENT

VIDEO IN

Good

picture

Basic

audio

Better

picture

Best

picture

Method 1 Method 2 Method 3

AUDIO OUT

(analog)

VIDEO OUT S-VIDEO OUT COMPONENT VIDEO OUT

Video

Cable

(supplied)

S-Video

Cable

(commercially

available)

Component

Video

Cable

(commercially

available)

Audio

Cable

(supplied)

• Method 1 DVD Player + TV with Video Input Jack

• Method 2 DVD Player + TV with S-Video Input Jack

• Method 3 DVD Player + TV with Component Video Jacks

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 13

–

Connection to a TV with an HDMI Compatible Port

CONNECTIONS

A simple 1-cable connection (using a commercially available cable) with a device having an HDMI (High-

Definition Multimedia Interface) connector allows digital transfer of the digital images of DVD-Video and other

sources.

To HDMI Input

Connector

A display equipment with an HDMI compatible port

HDMI cable

(commercially available)

NOTES:

• When using an HDMI-incompatible or HDCP-incompatible display equipment, the image will not be viewed properly.

• Among the devices that support HDMI, some devices can control other devices via the HDMI connector; however, this play-

er cannot be controlled by another device vice the HDMI connector.

• The audio signals from the HDMI connector (including the sampling frequency, the number of channels and bit length) may

be limited by the equipment that is connected.

• Among the monitors that support HDMI, some do not support audio output (for example, projectors). In connections with

equipment such as this, audio signals are not output from the HDMI output connector.

• When the set’s HDMI connector is connected to a DVI-D compatible monitor (HDCP compatible) with an HDMI-DVI convert-

er cable (commercially available), the signals are output in digital RGB.

*HDMI: High-Definition Multimedia Interface

To play back the digital video images of a DVD via an HDMI connection, it is necessary that both the player and the display

equipment (or an AV amplifier) support a copyright protection system called HDCP (High-bandwidth Digital Content

Protection System). HDCP is copy protection technology that comprises data encryption and authentication of the connect-

ed AV equipment.

This player supports HDCP. Please read the operating instructions of your display equipment (or AV amplifier) for more

information.

DOLBY DIGITAL/DTS Setting

Audio Recording Format

BITSTREAM *1 PCM or OFF

Dolby Digital Dolby Digital

2channel PCM

DTS DTS –DVD-Video

LPCM 2channel PCM 2channel PCM

Audio CD 2channel PCM 2channel PCM

MP3/WMA 2channel PCM 2channel PCM

*1 If the connected equipment is not compatible with HDMI BITSTREAM, signals are output on PCM.

C Actual output modes by media

“HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC.”

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 14

–

English

During playback, press the

STILL/PAUSE button.

• Playback will pause and sound

will be muted.

To continue playback, press the PLAY button.

NOTE:

• On DVDs, set “STILL MODE” to “FIELD” on the display

menu if pictures in the pause mode are blurred (refer to

page 23).

WMAJPEGMP3CDDVD

Still / Pause

Getting started

•Turn on the power of the TV, amplifier and any other com-

ponents which are connected to the DVD player.

• Make sure the TV and audio receiver (commercially avail-

able) are set to the correct channel.

Press the POWER ON button.

• “P-ON” will appear briefly on the display panel.

Press the OPEN/CLOSE button

to open disc loading tray.

Place the disc in the tray, with the

label facing up.

Press the PLAY button.

•The tray will close automatically,

then playback will start from the first

chapter or track of the disc. If the playback does not

start automatically, press the PLAY button.

•When you play back the DVD with a title menu, it may

appear on the screen. In this case, refer to “Title Menu”.

Press the STOP button to stop playback.

NOTES:

•A “prohibited icon” may appear at the

top-right corner on the TV screen during

operation, warning that a prohibited

operation has been encountered by the

DVD player or the disc.

•With DVDs that use some titles for playback program

signals, playback may start from the second title, or it

may skip these titles.

• During the playback of two layered disc, pictures may

stop for a moment. This happens when the 1st layer

switches to the 2nd layer. This is not a malfunction.

•

The operation may vary when you play back DVDs with disc

menu. Refer to the manual accompanying the disc for details.

WMAJPEGMP3CDDVD

Press the MENU button.

• The DVD main menu will appear.

If the feature is not available, symbol may

appear on the TV screen.

If disc menu is available on the disc, audio lan-

guage, subtitle options, chapters for the title and

other options will appear for selection.

Press the Cursor buttons (K / L / s / B) to select an

item, and the ENTER button to confirm the selection.

DVD

DISC PLAYBACK

Basic Playback

Disc Menus

DVD may contain menus to navigate the disc and access spe-

cial features. Press the appropriate Numeric buttons or use the

Cursor buttons (K / L / s / B) to highlight your selection in the

DVD main menu and press the ENTER button to confirm.

NOTE:

•

Unless otherwise stated, all operations described in this

manual are based on remote control use. Some operations

can be carried out using the menu bar on the TV screen.

DVD

General Features

Press the TOP MENU button.

• The title menu will appear.

If the feature is not available, symbol may

appear on the TV screen.

Press the Cursor buttons (K / L / s / B) to select an

item, and the ENTER button to confirm the selection.

• Playback will begin at the selected title.

DVD

Title Menu

• Press the MENU button to call up the DVD main menu.

• Press the TOP MENU button to call up the title menu.

NOTE:

• Contents of menus and corresponding menu opera-

tions may vary among discs. Refer to the manual

accompanying the disc for details.

DVD

CALLING UP A MENU SCREEN DURING PLAYBACK

Press the DIMMER button on the front panel to

select the desired brightness of the front panel dis-

play. (BRIGHT, DIMMER or OFF)

• The default setting is BRIGHT.

NOTES:

•The brightness of the front panel display can be adjust-

ed from the setup menu. Details are on page 25.

• When you turn on the power next time, the brightness

of the front panel display will be as set in setup menu.

Brightness of the Front Panel Display

HDMI Setup

Press the HDMI button on the front panel to select

the HDMI output mode.

The output mode changes as follows every time

the HDMI button is pressed.

• The HDMI indicator on the front panel lights up when

HDMI output mode is on.

480P (Default):

Video output from the HDMI OUT jack at 480p.

720P : Video output from the HDMI OUT jack at 720p.

1080 : Video output from the HDMI OUT jack at 1080i.

OFF : No video output from the HDMI OUT connector.

NOTES:

• Video and audio signals may distorted temporarily

when switching to/from the HDMI output mode.

•

Use a display equipment with an HDMI-compatible port.

•

The unit is sending Progressive video signal and HDMI

signal simultaneously when HDMI mode is set to ON. If

you connected component video cable to your TV, which

is not compatible with progressive scan, the distorted pic-

ture will be output.

•

The HDMI indicator on the front panel flashes when you

select the HDMI output mode but there is no HDMI cable.

•You can check the HDMI connection status by pressing

the DISPLAY button during playback with the HDMI

output mode (refer to page 20).

• If the TV is not compatible with newly selected HDMI

output mode, the actual output mode will be kept the

one before changing the selection. When this occurs,

the newly selected mode will appear on the front panel

display (see page 10) while the actual output resolution

will be indicated by performing the on-screen display as

described on page 20.

•You cannot select the HDMI output mode when the

setup menu is on the TV screen.

720P 1080 OFF

480P

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 15

–

DISC PLAYBACK

During playback, press the STILL/PAUSE button.

Press the h or g button.

• Slow motion playback will begin and

sound will be muted.

Press the h or g button repeat-

edly to select a desired speed.

•

Slow forward or reverse speed is differ-

ent depending on the disc. Approximate

speed is 1 (1/16), 2 (1/8), and 3 (1/2).

To return to normal playback, press

the PLAY button.

NOTE:

• On DVDs, set “STILL MODE” to “FIELD” on the Display

menu if pictures in the slow playback mode are blurred

(refer to page 23).

DVD

Slow Forward / Slow Reverse

Button

During playback, press the

STILL/PAUSE button.

• Playback will pause and sound

will be muted.

The disc advances frame by frame each time the

STILL/PAUSE button is pressed.

To exit step by step playback, press the PLAY button.

NOTE:

• On DVDs, set “STILL MODE” to “FIELD” on the display

menu if pictures in the pause mode are blurred (refer to

page 23).

DVD

Step by Step Playback

This function allows you to enlarge the video image and to

pan through the zoomed image.

Press the ZOOM button during playback.

• Playback will continue.

Press the ZOOM button repeatedly to select a

desired zoom factor: x2, x4 or off.

• Only x2 zoom is available for JPEG.

Use the Cursor buttons (K / L / s / B) to move

the zoomed picture across the screen.

To exit zoom mode, press the ZOOM button.

NOTES:

•

Zoom function does not work while disc menu is shown.

• x4 zoom is not available on some discs.

•Navigation screen is not available on JPEG.

•

You cannot pan through the zoomed picture on some JPEG files.

JPEGDVD

x2 x4

Zoom

DVD

Title / Chapter Search

Press the SEARCH MODE button

repeatedly until the chapter

search or the title search display

appears during playback.

Enter the desired chapter/title

number with the Numeric buttons.

By using the SEARCH MODE button

/29

By using the SKIP buttons

HH GG

During playback, press the

SKIP

button to move to the

next chapter. Press it repeatedly to skip to subsequent chap-

ters. Press the

SKIP

button to go back to the beginning

of the current chapter. Press it repeatedly to go to the previ-

ous chapters.

•

Chapter number will appear briefly on the front panel display.

• If the SKIP

button is pressed while the playback

is paused, the playback after skipping to the next chapter

will be also paused.

NOTES:

• Depending on the disc being played, the Numeric

buttons can be used to search for a desired chapter by

entering the chapter number directly. Refer to the man-

ual accompanying the disc.

• The SKIP

and

buttons are not available when

playback is stopped.

•A disc that does not contain chapters within titles, the

SKIP

and

buttons change the titles.

During playback, press the h or g button repeat-

edly to select a desired forward or reverse speed.

•For DVDs, fast forward or reverse search speed is dif-

ferent depending on the disc. The approximate speed is

1 (x2), 2(x8), 3 (x20), 4 (x50), and 5 (x100).

•For Audio CDs, MP3 and WMA, the approximate speed

is 1 (x2), 2 (x8), and 3 (x16).

•For Audio CDs, MP3 and WMA, sound will be output at

any speed of fast forward and reverse search.

To return to normal playback, press the PLAY button.

WMAMP3CDDVD

Fast Forward / Reverse Search

234

Button

1234

Button

During playback, press the

STOP button.

• Resume message will appear

on the TV screen.

Press the PLAY button, play-

back will resume from the point

at which playback was stopped.

•To cancel resume, press the STOP button twice.

NOTES:

• The resume information be saved even when the power

is turned off.

•For MP3, JPEG or WMA, playback will resume from the

beginning of the current track.

WMAJPEGMP3CDDVD

Resume

Press 'PLAY' to play from here.

To play the beginning,

press 'STOP' first and then 'PLAY'.

Resume ON

<Example: DVD>

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 16

–

English

To activate Repeat function, press the REPEAT button during

playback.

• The repeat mode changes as described below every time

you press the button.

REPEAT TRACK / GROUP / ALL

To activate Repeat function, press the REPEAT button during

playback.

• The repeat mode changes as described below every time

you press the button.

DVD

NOTES:

• The Repeat Title/Chapter setting will be cleared when

moving to other title or chapter.

• Repeat playback does not function during A-B repeat

playback.

• Repeat Title/Chapter is not available with some scenes.

Repeat

REPEAT TITLE / CHAPTER

• The REPEAT button is available only during playback.

NOTES:

• In the track repeat, the repeat setting will be cleared

when moving to other track.

• Repeat playback does not function during A-B repeat

playback.

CHAPTER TITLEOFF

(current chapter repeat) (current title repeat)

(repeat off)

TRACK ALLOFF

(current track repeat) (entire disc repeat)

(repeat off)

DISC PLAYBACK

Press the SEARCH MODE button until the time

search screen appears on

the TV screen.

Within 30 seconds, enter a

desired disc time point on the

disc with the Numeric buttons.

• Playback will start at the specified time.

•For Time Search, “0” appears automatically when there

is no need to enter a number. For example,

“0:0_:_ _” appears in the time search screen if the total

time of the disc is less than 10 minutes.

Press the CLEAR button to erase an incorrect input.

CDDVD

1:23:45

Time Search

Marker Setup Screen

You can use markers to memorize your favorite places on a disc.

Press the SEARCH MODE

button repeatedly until the

display screen and Markers

appear during playback.

Press the Cursor buttons

(s or B) to select 1, 2, 3,

4, 5, 6, 7, 8, 9, or 10 and ensure that “_ _ : _ _ : _ _”

appears in the display.

CDDVD

1 2 3 4 5 6 7 8 9

During playback, press the

SKIP

button to move to the next

track. Press it repeatedly to skip to subsequent tracks. Press the

SKIP

button to go back to the beginning of the current track.

Press it repeatedly to go to the previous tracks

•

Track number will appear briefly on the front panel display.

• If the SKIP

button is pressed while the play-

back is paused, the playback will be paused again after

skipping to the next track.

NOTE:

• The

SKIP

and

buttons are not available when

playback is stopped.

By using the SKIP buttons

HH GG

There are two ways to begin playback an Audio CD, MP3, JPEG

or WMA disc at a specific track.

WMAJPEGMP3CD

Track Search

Press the SEARCH MODE button.

•The track search display

appears.

Within 30 seconds, select a desired track number using

the Numeric buttons.

•For the disc with less than 10 tracks, press the track

number directly.

•For discs with 10 or more but less than 100 tracks, to

play back a single-digit track, press 0 first, then the

track number (e.g. for track 3, press 0, 3). To play back

a double-digit track, press the track number.

•For discs with 100 or more tracks, to play back a sin-

gle- or a double-digit track, press 0 first, then the track

number (e.g. for track 3, press 0, 0, 3, and for track 26,

press 0, 2, 6). To play back a triple-digit track, press the

track number.

• Press the CLEAR button to erase the incorrect input.

NOTE:

• The +10 button can also bring up the track search dis-

play except for the disc with less than 10 tracks. For

such a disc, track search can be done by just pressing

the track number.

__/ 15

By using the SEARCH MODE button

When the disc reaches the point you want to

remember, press the ENTER button.

• The title or track and elapsed playback time will appear

in the TV screen.

To return to the Marker later, press the SEARCH

MODE button repeatedly during playback and the

Cursor buttons

(s or B) to choose a desired

marker, then press the ENTER button.

Press the SEARCH MODE or RETURN button to exit.

NOTES:

• Opening the disc tray, turning off the power or selecting

AC at step and pressing the ENTER button will

erase all Markers.

•To clear a marker, using the Cursor buttons (s or B),

position the cursor on to the marker number to be

cleared and press the CLEAR button.

•You can mark up to 10 points.

NOTE:

• In the track or group repeat, the repeat setting will be

cleared when moving to other track or group.

WMAJPEGMP3

TRACK ALL

OFF

(current track

repeat)

(entire disc

repeat)

(repeat off)

GROUP

(current folder

repeat)

E6AH0UD(EN).qx3 2006.5.9 14:54 Page 17

–

This function allows you to program a playback order of

Audio CD, MP3, JPEG or WMA in a desired sequence.

In stop mode, press the MODE button.

• The program screen will appear.

Press the Cursor buttons

(▲ or ▼) to select a track, then

press the ENTER button.

•

Press the CLEAR button to erase

the most recently entered track.

Press the PLAY button to start

programed playback.

DISC PLAYBACK

Program Playback

CD-DA TOTAL 0:03:30

PROGRAM

1 3:30

2 4:30

3 5:00

4 3:10

5 5:10

6 1:30

7 2:30

1 3:30

1/2

1/1

In stop mode, press the MODE

button.

• The program screen will appear.

Press the Cursor buttons (K or

L) to select a group, then press

the ENTER button.

•A track selection screen appears.

Press the Cursor buttons (K or

L) to select a track, then press

the ENTER button to save it in

a program.

• Press the CLEAR button to erase

the most recently entered track.

• The programed track is displayed

in the right-hand screen.

• If the entire program cannot be dis-

played on the screen, “

L” appears.

• Pressing the Cursor button (s)

will show a list of folders that

belong to the hierarchy which is

one-level higher than the currently

selected folder.

Press the PLAY button to start programed playback.

• Press the RETURN button, and the stop screen will

show up with the program contents in memory.

WMAJPEGMP3

1/1

MY COLLECTION

ALL CLEAR

PROGRAM

ABC

DEF

GHI

ABC

1/1

PROGRAM

ABC

2/2

1/1

PROGRAM

ABC

DEF

GHI

JKL

MNO

DEF

GHI

JKL

MNO

2/2

This function shuffles the playback order of tracks instead of

playback in the original sequence.

In stop mode, press the

RANDOM button.

• The random screen will appear.

Press the PLAY button to start

random playback.

NOTES:

•To repeat the current track in the random selection,

press the REPEAT button repeatedly until TRACK

appears during playback. To repeat the entire random

selection press the REPEAT button repeatedly until

ALL appears during playback.

•You cannot go back to the previous track during ran-

dom playback.

•For a disc containing mixed MP3, JPEG and WMA

files, random playback of those files will be performed.

• “SHUFFLE” is displayed on the front panel display at

step .

WMAJPEGMP3CD

CD-DA TOTAL 0:45:55

RANDOM

RANDOM PROGRAM

--no indication--

<Example: CD>

Random Playback

When a CD-R or CD-RW disc with MP3, JPEG or WMA files

is inserted in the DVD player, the file list will appear automat-

ically on the TV screen. The number of tracks is also dis-

played on the front panel.

Press the Cursor buttons (K or L) to select the desired

group (folder) or track.

•To return to the previous screen, press the Cursor but-

ton (s).

• If a group (folder) is selected, press the Cursor button

(B) or ENTER button to go on to the track selection

screen. Press the Cursor buttons (K or L) to choose a

track, then press the PLAY or ENTER button.

• If a track is selected, press the PLAY or ENTER button

to start playing back tracks. The selected track and the

subsequent tracks will be played back.

WMAJPEGMP3

MP3 / JPEG / WMA Playback

Press the A-B REPEAT button

at your chosen starting point.

• A- appears briefly on the

TV screen.

Press the A-B REPEAT button

again at your chosen end

point.

• A-B appears briefly on the TV screen, and the

repeat sequence begins.

To exit the sequence, press

the A-B REPEAT button.

NOTES:

• The A-B Repeat section can only be set within the cur-

rent title (for DVD), or current track (for Audio CD).

• A-B Repeat is not available with some scenes on DVD.

•To cancel the A point which was set, press the CLEAR

button.

• A-B Repeat playback does not function during title,

chapter, track or all repeat playback.

A-B REPEAT

CDDVD

A -

A - B

OFF

NOTES:

• Press the STOP button once and then the PLAY button

again, playback will restart from the point where the

STOP button was pressed. (Program continued.)

• Press the STOP button twice and then the PLAY button

again, playback will restart from the first track in the

usual way. Your program is still stored until either the

disc tray is open or power is turned off.

•Up to 99 tracks can be entered.

•

To erase tracks in the program all together, select ALL

CLEAR at the bottom of the list at step . And, “A-CLEAr”

is displayed on the front panel display at that time.

•To repeat the current track in the program, press the

REPEAT button repeatedly until TRACK appears

during playback. To repeat the entire program press the

REPEAT button repeatedly until ALL appears dur-

ing playback.

• If eight or more tracks were set in a program, use the

SKIP

button to see all the tracks.

• When selecting the folder:

–Press the Cursor button (B) when you want to go to

the next hierarchy.

–

Press the Cursor button (

{

) when you want to go back

to the previous hierarchy (except for the top hierarchy).

•Even if an inserted disc contains mixed MP3, JPEG

and WMA files, Program function allows 99 tracks in

combination of MP3, JPEG and WMA files.

• The front panel display has blinked while setting the

program playback.

E6AH0UD(EN).qx3 2006.5.9 14:55 Page 18

–

English

DISC PLAYBACK

Applicable WMA file Remarks

Sampling

frequency

44.1kHz

48kHz

• Those frequencies are

applicable to WMA version 9.

Bit rate 48–192kbps

• Ensure that the copyright

function is set to off when

preparing a WMA disc.

Type WMA version 9

• A prohibition “disable” sym-

bol will appear if the user

attempts to run a non-repro-

ducible file such as copy-

right-protected.

• Recorded in multi-channel

format cannot be played

back.

This player recommends the use of files recorded at the fol-

lowing specifications:

Information on MP3, JPEG and WMA discs

•

This DVD player can play back images and sounds from data

recorded in MP3 and JPEG formats on CD-R and CD-RW discs.

•

A file with an extension of “.mp3 (MP3)” is called an MP3 file.

•A file with an extension of “.jpg (JPG)” or “.jpeg (JPEG)” is

called a JPEG file.

The DVD player can run an image file conforming to the

Exif specification. Exif is a file format, Exchangeable

Image File format established by Japanese Electronic

Industry Development Association (JEIDA).

•

A file with an extension of “.wma (WMA)” is called a WMA file.

• Files whose extension is other than “.mp3 (MP3)”, “.jpg

(JPG)” and “.jpeg (JPEG)” or “.wma (WMA)” will not be

listed on the MP3, JPEG or WMA menu.

• If the file is not recorded in MP3, JPEG or WMA format,

noise may be produced even if the file extension is either

“.mp3 (MP3)”, “.jpg (JPG)”, “.jpeg (JPEG)” or “.wma (WMA)”.

•

The name of group and track can be displayed up to 25 char-

acters. Unrecognizable characters will be replaced with aster-

isks. The ninth and deeper hierarchies cannot be displayed.

• Unplayable groups or tracks may be displayed depending

on the recording conditions.

• If the TOP MENU button is pressed when a file list is dis-

played, the first item will be highlighted.

Kodak Picture CD

The DVD player can also run JPEG files stored on Kodak

Picture CDs. You can enjoy picture images on the television

set by playing back the Picture CDs.

For details of Kodak Picture CD, contact a shop that provide

developing service of Kodak Inc.

Applicable MP3 file Remarks

Sampling

frequency

44.1kHz

48kHz

• It is prohibited to record

MP3 sound on a digital

device when the connection

is made digitally.

Type

MPEG1

audio layer 3

• MP3 files recorded at fixed

bit rate of 32 kbps or higher

are recommended.

Applicable JPEG file Remarks

Size of

image

Upper limit:

6300x5100 dots

Lower limit:

32x32 dots

• A JPEG image that extends

beyond the screen is

reduced so that it will be

displayed within the screen.

When Kodak Picture CD is

inserted in the DVD Player,

Kodak Picture CD menu

appear automatically on

the TV screen.

• If all menu items cannot be

displayed on the screen

scope, “G” appears at the

right bottom of the screen,

indicating that the user can

view remaining items on the next page. “H” appears, it

indicates that the user can view other items on the pre-

vious page. The track number of the currently highlight-

ed item and the total tracks are shown at the center bot-

tom of the screen.

• If “G” is shown at the right bottom, use the SKIP G

button to view the next page. If “H” is shown at the left

bottom, use the SKIP H button to view the previous

page.

• It may take some time until all menu items are dis-

played on the menu screen.

Press the Cursor buttons (K / L / s / B), select a

desired track to be played back, then press the

PLAY or ENTER button.

• If a Kodak Picture CD file is selected, an image will be

played back from the selected track and go to the next

one in turn.

Press the STOP button, to stop playback.

NOTES on JPEG and Kodak Picture CD:

•A track is displayed for 5 or 10 seconds and then the

next track is displayed.

•Every press on the ANGLE button will turn the image

clockwise by 90 degrees when an image is displayed.

•To change the size of the playback image, press the

MODE button twice. The size change mode appears on

top of the TV screen during playback. Then press the

Cursor buttons (s or B) or ENTER button to switch

between NORMAL (100%) and SMALL (95%).

Picture1 Picture2 Picture3

Picture4

Current track number /

the number of total tracks

Picture5 Picture6

1/32

• When selecting the folders

–Press the Cursor button (

) when you want to go to

the next hierarchy.

–Press the Cursor button ({) when you want to go

back to the previous hierarchy (except for the top hier-

archy).

• Press the TOP MENU button to return to the first item.

Press the STOP button to stop playback.

NOTES:

• Folders are known as Groups; files are known as Tracks.

• A symbol of is shown on the top of the group name.

• A symbol of is shown on the top of MP3 files.

• A symbol of is shown on the top of JPEG files.

• A symbol of is shown on the top of WMA files.

• Maximum of 255 folders can be recognized.

• Maximum of 999 files can be recognized.

• Up to 8 hierarchies can be recognized.

• If the track extends beyond the scope of screen, a

down arrow “L” appears, indicating that the user can

view another part on the previous page. The current

page number and the number of total pages are shown

on the left of the down arrow “L”.

• If no MP3, JPEG or WMA files are found in the group,

the group is not displayed.

• The DVD player can reproduce data recorded as per

ISO 9660 Level 1, Level 2 or Joliet on the disc.

• It can also run a disc on which data is recorded in a

multi-session.

• For more details of recording systems, refer to the

instruction manual for the CD-R / CD-RW drive or the

writing software.

• For MP3 and WMA files recorded in Variable Bit Rate

(VBR), the unit may not display the actual elapsed

time.

E6AH0UD(EN).qx3 2006.5.9 14:55 Page 19

–

DISC PLAYBACK

Press the DISPLAY button

during playback.

• Current file name will be dis-

played.

<Example: MP3>

Press the DISPLAY button.

• Current track number/total

tracks and elapsed time (MP3)

will be displayed.

• Current repeat setting appears only when the Repeat

setting is active.

(T:Track repeat/ A: All (disc) repeat/ G: Group

repeat).

• When you are playing back a disc with MP3 or JPEG

files in program or random mode, PROGRAM (or

RANDOM) will be displayed.

Press the DISPLAY button again.

• During program or random playback, each playback

status will be displayed when you press the DISPLAY

button. Then press the DISPLAY button to exit.

Press the DISPLAY button again.

•

Current HDMI status will be displayed during the HDMI output

mode. (Refer to NOTE FOR HDMI DISPLAY on this page.)

Press the DISPLAY button again to exit.

JPEGMP3

TRACK 01

TR 1/36 0:01:15

Press the DISPLAY button

during playback.

•

Current file name will be displayed.

Press the DISPLAY button again.

• Title name based on tag infor-

mation of currently played-

back file will be displayed.

Press the DISPLAY button

for the third time.

•Artist name based on tag infor-

mation of currently played-

back file will be displayed.

Press the DISPLAY button again.

•Current track number/total

tracks and elapsed time

will be displayed.

• Current repeat setting appears only when the Repeat

setting is active.

(T:Track repeat/ A: All (disc) repeat/ G: Group

(folder) repeat).

•

When you are playing back a disc in program or random

mode, PROGRAM (or RANDOM) will be displayed.

Press the DISPLAY button again.

• During program or random playback, each playback

status will be displayed when you press the DISPLAY

button. Then press the DISPLAY button to exit.

Press the DISPLAY button again.

•

Current HDMI status will be displayed during the HDMI output

mode. (Refer to NOTE FOR HDMI DISPLAY on this page.)

Press the DISPLAY button again to exit.

NOTE:

• If the file does not contain tag information, NOT AVAIL-

ABLE will be displayed.

WMA

TRACK 01

TITLE NAME

ARTIST NAME

TR 1/36 0:01:15

You can check information about the current disc by pressing

the DISPLAY button on the remote control.

Press the DISPLAY button

during playback.

• Current chapter number/total

chapters, elapsed time and

remaining time of the current chapter, and current play-

back status will be displayed.

Press the DISPLAY button again.

• Current title number/total titles, elapsed time and

remaining time of the current title, and current playback

status will be displayed.

Press the DISPLAY button

for the third time.

• The bit rate (the amount of

video data currently being

read) and current playback status will be displayed.

• Current repeat setting appears on the display bar only

when the repeat setting is active.

(C:Chapter repeat/ T: Title repeat/A B: A-B

repeat)

• If you are playing back a two-layered disc, the layer

number will also be displayed.

(L0: Layer 0 is played back. L1: Layer 1 is played back.)

Press the DISPLAY button again.

• Current HDMI status will be displayed during the HDMI

output mode. (Refer to NOTE FOR HDMI DISPLAY on

this page.)

Press the DISPLAY button again to exit.

DVD

IIIIIII

T L1

Changing the On-Screen Display

9/49 0:00:00 -0:03:30

• Progressive JPEGs (JPEG files saved in the progres-

sive format) will not be played back on this DVD player.

• High resolution JPEG files take longer to be displayed.

• The size change mode may have no effect on some

files (e.g. files with a small picture size).

NOTES on WMA:

• The DVD player can reproduce data recorded as ISO

9660 level 2 with 31 characters file name included

punctuation marks. The name of file can be displayed

up to 25 characters.

• Maximum of 8 subfolders can be recognized.

• It can also be displayed tag information of WMA at

least 64 characters.

•A file with an extension of Joliet as Unicode format in

up to 64 characters can be recognized.

•

This unit cannot play back copyright protected WMA files.

NOTE FOR HDMI DISPLAY:

• The displayed HDMI status

are as follows:

1. Information for image out-

put/Resolution of image

2. Sound output format

3. Maximum number of audio channels that can be

accepted by the connected equipment

VIDEO INFO. :

YCbCr/1080i

AUDIO INFO. :

BITSTREAM

MAX CHANNEL

: 2ch

Press the DISPLAY button during playback.

• Current track number/total tracks, elapsed time and

remaining time of the current track, and current play-

back status will be displayed.

• Current repeat setting appears on the display bar only

when the Repeat setting is active.

(T:Track repeat/ A: All tracks repeat/A B: A-B

repeat)

Press the DISPLAY button again.

• Current track number/total tracks, elapsed time and

remaining time of the entire disc, and current playback

status will be displayed.

• Current repeat setting appears on the display bar only

when the Repeat setting is active.

(T:Track repeat/ A: All tracks repeat/A B: A-B

repeat)

• When you are playing back a disc in program or random

mode, PROGRAM (or RANDOM) will be displayed.

Press the DISPLAY button again to exit.

E6AH0UD(EN).qx3 2006.5.9 14:55 Page 20

La page charge ...

Denon DHT-487DV Manuel utilisateur

Marque: Denon

Modèle: DHT-487DV

Catégorie: Lecteurs DVD

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Denon DHT-487DV User manual
español: Denon DHT-487DV Manual de usuario

Denon DHT-487DV Manuel utilisateur

Denon DHT-487DV Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents