Landice 90 Series L10 Guide d'installation

Marque: Landice

Modèle: 90 Series L10

Catégorie: Tapis de course

Taper: Guide d'installation

Part Number: 73208-5

L10 Treadmill

90 Series

Installation Manual

Contents

1. Important Safety Instructions ........................................... 3

1.1. Safety................................................................................... 3

1.2. Grounding Instructions......................................................... 5

1.3. 120-Volt Treadmills.............................................................. 6

1.4. 200 – 240-Volt Treadmills.................................................... 6

2. Installation ......................................................................... 9

2.1. Tools Needed ...................................................................... 9

2.2. Hardware Included............................................................... 9

2.3. Unpacking.......................................................................... 10

2.4. Assembly ........................................................................... 14

2.5. Cover Installation ............................................................... 23

2.6. Leveling Treadmill.............................................................. 25

2.7. Treadbelt Tensioning ......................................................... 27

2.8. Treadbelt Tracking............................................................. 28

1. Important Safety Instructions

1.1. Safety

Read all instructions before using the treadmill.

Save these instructions.

Veuillez lire toutes les instructions avant d'utiliser le tapis roulant.

VEUILLEZ CONSERVER CES INSTRUCTIONS.

DANGER

To reduce the risk of electric shock: always

unplug the treadmill from the electrical outlet

immediately after using and before cleaning.

To reduce the risk of burns, fire, electric shock

or injury to persons, keep the power cord away

from heated surfaces. Be sure the cord has

plenty of slack and cannot be pinched under the

treadmill when it elevates and de-elevates.

ATTENTION

Treadmills require more power than other

appliances and must be plugged into a

dedicated power outlet. Failure to follow these

guidelines may void product warranty.

• Always plug treadmill directly into wall outlet receptacle.

• Never use an extension cord, power strip, GFI or ARC

Fault Breaker outlet. Contact a qualified electrician to

add or move a power outlet if power cord does not reach

desired location.

• Check treadmill power cord connections (into treadmill

and wall outlet) frequently as a loose connection may

cause intermittent power loss or cause power cord to

overheat.

• Inspect power cord for wear or damage frequently; do

not operate treadmill with a damaged cord.

• Route power cord away from operating area; do not run

power cord under treadmill, carpeting or furniture.

• Position power cord away from high traffic areas to avoid

a tripping hazard.

Important Safety Instructions

DANGER

Pour réduire le risque d'électrocution : toujours

débrancher le tapis roulant de la prise électrique

immédiatement après son utilisation et avant de

le nettoyer.

Pour réduire le risque de brûlure, d'incendie,

d'électrocution ou de blessure corporelle, tenez

le câble électrique éloigné des surfaces

chauffées. Assurez-vous que le câble ait

suffisamment de mou et ne puisse pas se

coincer sous le tapis roulant lorsqu'il s'élève ou

s'abaisse.

ATTENTION

Les tapis de course nécessitent plus d'énergie

que les autres appareils et doivent être

branchés sur une prise de courant dédiée. Le

non-respect de ces directives peut annuler la

garantie du produit.

• Branchez toujours le tapis roulant directement dans la

prise murale.

• N'utilisez jamais de rallonge, de multiprise, de prise GFI

ou de disjoncteur ARC. Contactez un électricien qualifié

pour ajouter ou déplacer une prise de courant si le câble

électrique n'atteint pas l'emplacement souhaité.

• Vérifiez fréquemment les connexions du câble électrique

du tapis de course (dans le tapis de course et la prise

murale) car une connexion desserrée peut entraîner une

perte de courant intermittente ou une surchauffe du

câble électrique.

• Inspectez fréquemment le câble électrique pour détecter

toute usure ou dommage; n'utilisez pas le tapis de

course avec un cordon endommagé.

• Éloignez le câble électrique de la zone d'opération; ne

pas faire passer le câble électrique sous le tapis roulant,

la moquette ou les meubles.

• Éloignez le câble électrique des zones à fort trafic pour

éviter tout risque de trébuchement.

Important Safety Instructions

1.2. Grounding Instructions

This product must be grounded. if it should malfunction or break

down, grounding provides a path of least resistance for electric

current to reduce the risk of electric shock. The treadmill is

equipped with a cord having an equipment grounding conductor

and a grounding plug. The plug must be plugged into an

appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

WARNING

Failure to leave ample clearance around the

treadmill could cause you to be trapped

between the treadmill and a wall if you fall,

resulting in burns or other serious injury

from the moving treadbelt. Allow a

minimum clearance of 18 inches (46 cm) on

each side of the treadmill. Allow a minimum

clearance of 6 feet (183 cm) at the rear of the

treadmill.

WARNING

Connect treadmill to a properly grounded,

dedicated electrical outlet only. See the

following Grounding Instructions.

AVERTISSEMENT

Le fait de ne pas laisser suffisamment

d'espace dégagé autour du tapis roulant

peut avoir comme conséquence, en cas de

chute, que vous soyez immobilisé entre le

tapis roulant et un mur, la courroie en

mouvement pouvant causer des brûlures ou

autres blessures. Laissez un espace dégagé

d'au minimum 46 cm de chaque côté du

tapis roulant. Laissez un espace dégagé

d'au minimum 183 cm à l'arrière du tapis

roulant.

AVERTISSEMENT

Ne branchez le tapis roulant que sur une

prise électrique raccordée à la terre et

exclusivement dédiée au tapis roulant. Voir

les instructions de mise à la terre qui

suivent.

Important Safety Instructions

1.3. 120-Volt Treadmills

Treadmills marked 120 VAC are intended for use with a grounding

plug in a nominal 120-volt circuit. Ensure the treadmill power cord

is connected to an outlet having the same configuration as the

plug. No adapter should be used with 120 VAC treadmills.

1.4. 200 – 240-Volt Treadmills

Treadmills marked 200 – 240V AC are intended for use on a circuit

having a nominal rating greater than 220V and are factory-

equipped with a specific power cord and plug to permit connection

to a proper electrical circuit. Ensure the treadmill power cord is

connected to an outlet having the same configuration as the plug.

No adapter should be used with 200 – 240 VAC treadmills.

If the treadmill must be configured for use on a different type of

electrical circuit, qualified service personnel should make the

proper connection.

Ce produit doit être mis à la terre. En cas de dysfonctionnement ou

de panne, la mise à la terre offre une voie de moindre résistance

au courant électrique, ce qui réduit de risque d'électrocution. Le

tapis roulant est équipé d'un câble électrique muni d'un fil

conducteur de mise à la terre et d'une fiche de mise à la terre.

Cette fiche doit être branchée sur une prise adaptée, correctement

installée et raccordée à la terre conformément à tous les codes et

règlements locaux.

DANGER

Improper connection of the grounding connector

can result in a risk of electric shock. Check with a

qualified electrician/service technician if you are

in doubt as to whether the treadmill is properly

grounded. Do not modify the plug provided with

the treadmill–if it will not fit the outlet, have a

proper outlet installed by a qualified electrician.

Important Safety Instructions

Tapis de course 120 VCA

Les tapis roulants marqués 120 VCA sont conçus pour être utilisés

avec une prise de terre dans un circuit nominal de 120 volts.

Assurez-vous que le cordon d’alimentation du tapis de course est

branché sur une prise ayant la même configuration que la prise.

Aucun adaptateur ne doit être utilisé avec les tapis roulants 120

VAC.

Tapis roulant 200 – 240 volts

Les tapis roulant sur lesquels est inscrit 200-240 CA (VAC) sont

destinés à une utilisation à une tension nominale supérieure à 220

V et équipés en série d'un câble électrique et d'une fiche

spécifiques pour permettre le branchement sur une prise adaptée.

Si le tapis roulant doit être configuré pour une utilisation sur un

type de circuit électrique différent, il convient de faire appel à du

personnel de service qualifié pour installer le bon raccordement.

DANGER

Un mauvais raccordement à l'équipement de mise

à la terre vous expose à un risque d'électrocution.

Renseignez-vous auprès d'un électricien/

technicien de service qualifié en cas de doute sur

la mise à la terre correcte du tapis roulant. Ne

modifiez pas la fiche fournie avec le tapis roulant:

si elle ne convient pas à la prise, faites installer

une prise adaptée par un électricien qualifié.

Important Safety Instructions

2. Installation

2.1. Tools Needed

• M4-Allen Wrench 4mm (#22 on blister pack)

• M6-Allen Wrench 6mm (#21 on blister pack, blue handle)

Installer provides the following tools:

• Med Phillips Screwdriver

• Socket wrench 16mm

• Open end wrench 16mm

2.2. Hardware Included

The following hardware and tools are supplied:

Figure 2-1. Hardware and Tools Supplied on Blister Pack

• M6x15 Phillips screw: 6 pieces (#14 on blister pack)

• Serrated lock washers for M6 screws: 6 pieces (#17 on blister pack)

• M8x15 button head cap screws:18 pieces (#13, bag on blister pack)

• Serrated lock washers for M8: 18 pieces (#16 on blister pack)

• M5x25 Socket Head Cap Screws: 8 pieces (to attach motor cover)

#14 PHILLIPS SCREW M6*15 (6PCS)

#22 M4 ALLEN WRENCH (1PC)

#17 SERRATED LOCK WASHERS Ø6 (6PCS)

#13 BUTTON HEAD CAP SCREW M8*15 (18PCS)

L10

#10 BOLT M10*25 (4PCS) #16 SERRATED LOCK WASHERS Ø8 (18PCS)

#15 PHILLIPS SCREW M6*75 (4PCS)

#11 NYLON LOCK NUT M10 (2PCS)

#12 FLAT WASHER Ø11*Ø23*2 (2PCS)

#21 M6 ALLEN WRENCH (1PC)

SOCKET HEAD CAP SCREW M5*25 (8PCS)

Installation Unpacking

• M10x25 bolts: 4 pieces (#10 on blister pack)

• M10 Nylon Lock Nuts: 2 pieces (#11 on blister pack)

• M10 Flat Washers: 2 pieces (#12 on blister pack)

• M4x75 Phillips screws: 4 pieces (#15 on blister pack)

2.3. Unpacking

Unpacking and installation of the treadmill should be done by a

qualified technician. The packaged treadmill is very heavy and weighs

600 lbs (272KG), packaged.

1. Locate where the treadmill will be used to provide space as shown

in Figure 2-2.

Figure 2-2. Free Space Areas

WARNING

To avoid injury, use caution when moving

and lifting the treadmill during unpacking

and assembly.

AVERTISSEMENT

Pour éviter toute blessure, faites attention

lors du déplacement et du levage du tapis

roulant lors du déballage et de

l'assemblage.

24” (0.6m)

79” (2m)

12”

(0.3m)

Unpacking Installation

2. Move boxed unit to room where it will be used, cut the straps, and

take off the top of the box (Figure 2-3).

Figure 2-3. Open Shipping Box

3. Remove wood bracing from inside the box. You will have to slide

larger box toward center to remove wood brace covering it

(Figure 2-4).

Figure 2-4. Bracing Removal

4. Open the large box. Inside you will find:

• Plastic wrapped blister pack of hardware and tools

• Handrails

• Remote Console

• Cup holder

• Treadmill Lubricant

• Line Cord

• Manual and Warranty Card

Console/

Display Box

Large

Accessory

Box

Large

Accessory

Box

Console/

Display Box

Installation Unpacking

Figure 2-5. Large Accessory Box Contents

5. Open smaller box. Inside you will find the console/display

(Figure 2-6).

Figure 2-6. Console/Display

6. Remove Upright from box (Figure 2-7).

Figure 2-7. Packed Upright

Upright

Unpacking Installation

7. Cut open the box and remove bubble wrap (Figure 2-8). Lift motor

cover off and set aside.

Figure 2-8. Packed Base

8. Remove the Treadmill base from the box and place where it will be

used as determined in Step 1. One person uses the Grab Bar and

two people lift at each front corner as shown in Figure 2-9.

Figure 2-9. Base Removal

Grab Bar

Lift at corners

Installation Assembly

2.4. Assembly

1. On both sides: The M10x165 and M10x180 Hex Head Bolts used

to secure the Upright to the Frame are shipped in the Frame, held

in place during shipment with 16mm nuts. Remove and discard the

nuts and allow bolts to slide down and rest on the floor

(Figure 2-10).

Figure 2-10. Bolt Shipping Position

2. Untie wire tie from the Upright and leave wire in place. You will

need this to guide the Upper Wire Harness through the Upright

Upper Access Hole later.

3. Align the pins on the bottom of the Upright Plate with the holes in

the Frame and lower the Upright fully onto the Frame (Figure 2-11).

M10x180 Hex Head Bolt

M16 Nut (4X)

Remove and

discard

M10x165 Hex Head Bolt

Assembly Installation

Figure 2-11. Upright Installation

4. Remove the two Nylon Lock Nuts #11 and Flat Washers #12 from

the blister pack.

5. On both sides: Push the Rear Bolt up through the Frame and

Upright Base Plate and install the Nylon Lock Nuts and Flat

Washers. Do not fully tighten at this time.

6. Thread the Front Bolt into the Welded Nut on the Upright Base

Plate but do not fully tighten at this time.

7. On both sides: Thread the two M10x25 Hex Head Bolts through

Frame Bracket into the Upright as shown in the following figure

(Figure 2-12). Repeat steps for opposite side.

Figure 2-12. Upright Side Bolts

Alignment Pin

Welded Nut

Nylon Nut

Flat Washer

Front Bolt

Rear Bolt

Upright

M10x25 Hex Head

Bolts (4X, from

blister pack)

Installation Assembly

8. Tighten all four M10x25 Hex Head Bolts.

9. Tighten remaining hardware found in Step 1.

10. Slide Remote Console Assembly onto Center Upright Bracket and

the End Plates into the Side Brackets as shown in Figure 2-13.

Figure 2-13. Remote Console Assembly Installation

11. Attach the Remote Console Assembly to Center Upright Bracket

from the bottom using four M8x15 Socket Head Cap Screws (#13

on blister pack) with the blue (M6) Allen wrench provided on the

blister pack. Do not completely tighten (Figure 2-14).

Figure 2-14. Remote Console Assembly Center Upright Bracket

Mounting Hardware

Remote

Console

Assembly

End Plate

(both ends)

Side Brackets

(both sides)

Center

Upright

Bracket

M8x15 Socket Head Cap Screws (4X)

Assembly Installation

12. On both sides: Attach the Remote Console Assembly to the

Upright Brackets using one M8x15 Socket Head Cap Screw, found

on blister pack (Figure 2-15). Secure with 6mm Allen wrench.

Figure 2-15. Remote Console Assembly Plate Hardware

(both sides)

13. Remove the three M5x15 Socket Head Cap Screws holding the

Inner Handrail Covers to each Handrail, using the 4mm Allen

wrench, as shown in Figure 2-16 and place them in a safe place for

reuse later when the Covers are re-installed.

Figure 2-16. Handrail Inner Cover Hardware (both sides)

M8x15 Socket

Head Cap Screw

(1 per side)

M5x15 Socket Head

Cap Screw (3X)

Installation Assembly

14. Loosely attach each Handrail to the Upright Bracket and the

Remote Console Assembly End Plates with M8x15 Socket Head

Cap Screws and Lock Washers. Tighten all Screws that secure the

Remote Console Assembly to the Upright (6 per side, Figure 2-17).

Figure 2-17. Handrail Mounting Hardware

15. Install both Handrail Inner Covers with M5x15 Socket Head Cap

Screws (3 each side, previously removed in Figure 2-16) using

4mm Allen wrench.

16. Place the Accessory Tray over the Handrails and remove the

Accessories Cover. Ensure that the Ribbon Cable is routed through

the Cable Notch as indicated by the red arrow. (Figure 2-18).

Upright Bracket

End Plate

M8x15 Socket

Head Cap Screw

(12X)

Assembly Installation

Figure 2-18. Accessory Tray Installation - Upper Screws

17. Route the Ribbon Cable and Pulse Cable through the hole in the

Accessory Tray and the Upright indicated by the red arrow (Figure

2-18).

Figure 2-19. Ribbon and Pulse Cable Routing and Hardware

Accessory Cover

Ribbon Cable

from Remote

Console

Pulse Cable

from Remote

Console

M6x16 Button Head

Cap Screws (4X)

Pulse Cable

Ribbon Cable

Installation Assembly

18. Secure the Accessory Tray from above with four M6x16 Button

Head Cap Screws as shown using the 4mm Allen wrench (Figure

2-19).

19. Secure the tray from underneath with two M6x16 Button Head Cap

Screws as shown using the 4mm Allen wrench (Figure 2-20).

Figure 2-20. Accessory Tray Installation - Lower Screws

20. Remove Console/Display from box. There are three cables coming

from the bottom of the Console: the long Upper Wire Harness, the

flat ribbon cable, and the wireless pulse cable (Figure 2-21).

Figure 2-21. Console/Display Cables

M6x16 Button Head Cap

Screws (2x)

Wireless Pulse

Cable

Upper Wire

Harness

Guide Wire

Tie

Ribbon Cable

La page charge ...

Landice 90 Series L10 Guide d'installation

Marque: Landice

Modèle: 90 Series L10

Catégorie: Tapis de course

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Landice 90 Series L10 Installation guide

Landice 90 Series L10 Guide d'installation

Landice 90 Series L10 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents