West Marine VHF650 Le manuel du propriétaire

DSC Marine Radio

Owner’s Manual

Radio maritime ASN

Guide d’utilisation

Radio maritime ASN

Radio marina DSC

Manual del usuario

VHF650_WM_front.pdf 1/22/2007 1:12:44 PM

Making a distress call

Lift the red cover. Press and hold the

DISTRESS button for three seconds. The

VHF650 transmits your boat’s location

every few minutes until you receive a

response.

NOTE: If the radio displays Enter User

MMSI, cancel the automatic distress call

and make a normal voice distress call.

Lift the red cover

and press the

DISTRESS button.

Making a voice distress call

Speak slowly -- clearly -- calmly.

Make sure your radio is on.

On the microphone, press the 16/9-TRI button to switch to Channel 16

(156.8 MHz). (If the corner of the display does not show 16, press the

16/9-TRI button again until it does.)

Press the PUSH TO TALK button on the microphone and say: "MAYDAY

--MAYDAY-- MAYDAY."

Say "THIS IS ___________ ﬂWrite your boat’s name in the blank space

Say "MAYDAY ___________ ﬂWrite your boat’s name in the blank

space.

Tell where you are: (what navigational aids or landmarks are near, or

read the latitude and longitude from your GPS).

State the nature of your distress, e.g. are you sinking, medical

emergency, man overboard, on  re, adrift, etc.

Give number of persons aboard and conditions of any injured persons.

Estimate present seaworthiness of your ship, e.g. how immediate is the

danger due to  ooding or  re or proximity to shore.

Brie y describe your ship (length, type, color, hull).

Say: “I will be listening on Channel 16."

End message by saying "THIS IS ___________, OVER." ﬂWrite your

boat’s name or call sign in the blank space.

Release the PUSH TO TALK button and listen. If you do not get an answer

after 30 seconds, repeat your call, beginning at step 3, above.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

Making a Distress Call

Cómo hacer una llamada de apuro

Levante la tapa roja. Mantenga oprimido

el botón DISTRESS por 3 segundos. La

radio VHF650 transmitirá la localidad de

su navío cada cuantos minutos hasta que

reciba una respuesta.

Nota: Si la radio exhibe Enter User MMSI

(Inserte el MMSI del usuario), cancele la

llamada de apuro automática y haga una

llamada de apuro normal por voz.

Levante la tapa

roja y oprima el

botón DISTRESS.

Cómo hacer una llamada de apuro por voz

Hable despacio -- claro -- y con calma.

Asegúrese de que la radio está encendida.

En el micrófono, oprima el botón 16/9-TRI para cambiar al canal 16 (156.8

MHz). (Si la esquina de la pantalla no muestra 16, oprima el botón 16/9-

TRI otra vez hasta que lo haga.)

Oprima el botón PUSH TO TALK (Oprima para hablar) en el micrófono y

diga: “MAYDAY --- MAYDAY--- MAYDAY.”

Diga “ESTE ES ______________ ﬂ Escriba el nombre de su navío en

el espacio vacío.

Diga “MAYDAY _____________ ﬂ Escriba el nombre de su navío en el

espacio vacío.

Describa donde se encuentra: (ayudas de navegación o marcas

destacadas cercanas, o lea la latitud y la longitud en su GPS).

Describa la clase de su apuro, ej., se está hundiendo, emergencia

médica, hombre al agua, hay fuego, está a la deriva, etc.

Describa la cantidad de personas abordo y las condiciones de cualquier

persona lesionada.

Estime la navegabilidad actual de su navío, ej., cuanto de inmediato es

el peligro de inundación o de incendio o proximidad a la costa.

Describa brevemente su navío (largura, tipo, color, casco).

Diga: “Estaré escuchando en el canal 16.”

Termine el mensaje diciendo: ‘ESTE ES ________, OVER.” ﬂ Escriba

el nombre de su navío o la señal de llamada en el espacio vacío.

Suelte el botón PUSH TO TALK y escuche. Si no recibe una contestación

dentro de 30 segundos, repita su llamada, comenzando con el paso 3,

descrito arriba.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

Faire un appel de détresse

Soulevez le couvercle rouge. Maintenez

la touche DISTRESS enfoncée pendant trois

secondes. Le VHF650 transmet la position

de votre bateau à intervalles réguliers de

quelques minutes, jusqu’à ce que vous

receviez une réponse.

REMARQUE : Si la radio af che Enter

User MMSI (Entrer l’ISMM de l’utilisateur),

annulez l’appel de détresse

automatique et faites un appel de détresse

vocal standard.

Soulevez le

couvercle rouge

et appuyez sur la

touche

DISTRESS

.

Faire un appel de détresse vocal

Parlez lentement – clairement – calmement.

Véri ez si votre radio est en marche.

Appuyez sur la touche 16/9-TRI du microphone a n de commuter au canal

16 (156,8 MHz). (Si le canal 16 n’apparaît pas à l’af chage, appuyez de

nouveau sur la touche 16/9/TRI jusqu’à ce qu’il soit af ché.)

Appuyez sur le bouton de microphone PUSH TO TALK et dites : “MAYDAY

- MAYDAY – MAYDAY”.

Donnez l’identité de votre navire en disant : “ICI _________” fÉcrivez le

nom de votre bateau dans l’espace vierge ci-contre.

Dites “MAYDAY___________” f Écrivez le nom de votre bateau dans

l’espace vierge ci-contre.

Donnez votre position : (quels sont les points de repère ou aides à la

navigation près de vous ou lisez les coordonnées de longitude et de latitude

apparaissant sur votre dispositif GPS).

Révélez la nature de votre détresse, par exemple, nous sommes en train de

couler, urgence médicale, un homme à la mer, un incendie, nous sommes à

la dérive, etc.

Donnez le nombre de personnes à bord et les conditions des blessés, s’il y

en a.

Donnez la condition de navigabilité actuelle de votre navire, tel que le degré

de l’urgence par rapport à l’inondation, à l’incendie ou à votre proximité de la

côte.

Donnez une brève description de votre navire (métrage, type, couleur,

coque).

Dites : “Je vais écouter sur le canal 16”.

Terminez le message en disant “ICI ___________ , À VOUS” f Écrivez le

nom de votre bateau dans l’espace vierge ci-contre.

Relâchez le bouton PUSH TO TALK du microphone et écoutez. Si vous

n’obtenez pas de réponse après 30 secondes, répétez l’appel en

commençant à l’étape 3 ci-dessus.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

E-2

Table of Contents

Making a Distress Call ....... Inside

Front Cover

Making a voice distress

call ..................Inside Front Cover

Table of Contents .........................2

Introduction ...................................4

Features .....................................4

Manual overview ........................4

Conventions ............................4

Terms used in this manual .......5

Getting Started ..............................6

What's included .............................6

Parts of the radio ...........................7

Turning on the radio .....................10

Setting the UIC channel mode

(USA/CAN/INT) ...........................10

How it Works ...............................10

Normal mode operation ............11

Using the radio in normal

mode .....................................12

Normal mode with Weather

Alert Watch ............................12

Normal mode with Triple and

Dual Watch ............................13

Normal mode with both Weather

Alert and Triple/Dual Watch ...13

Scan mode ...............................14

Using the radio in scan

mode .....................................14

Scan mode with Weather Alert

Watch ....................................15

Scan mode with Triple and Dual

Watch ....................................15

Scan mode with both Weather

Alert and Triple/Dual Watch ...16

Weather mode ..........................16

Using the radio in weather

mode .....................................16

Weather mode with Weather

Alert Watch ............................17

Weather mode with Triple and

Dual Watch ............................17

Using Your Radio ........................18

Making a voice MAYDAY

call ............................................19

Setting the volume ...................19

Setting the squelch level ..........19

Changing the channel ..............20

Making a transmission .............20

Boosting the transmission

power .....................................20

Choosing Triple Watch or Dual

Watch .......................................21

Using FIPS codes for weather

alerts ........................................21

Changing display and sound

options ......................................23

Contrast .................................23

Lamp adjust ...........................23

Turning the key beep on and

off ..........................................23

Setting the GPS position

manually ...................................23

Using Digital Selective Calling

(DSC) Features............................25

What is DSC? ...........................25

Advanced DSC features ...........25

Getting an MMSI number .........26

Entering MMSI numbers ..........26

Individual or user MMSI

number ..................................26

Group MMSI number .............27

Using the directory ...................28

Making DSC calls .....................30

Calling a single station

(Individual Call) ......................31

Calling a particular group of

stations (Group Call) .............32

Calling all stations (All-Ships

Call) .........................................32

Making an automatic distress

call............................................33

Canceling an automatic

distress call ............................33

Receiving a DSC call ...............34

Receive log ..............................34

Returning a call .....................35

Requesting another station's

position (POS Request) ...........35

Receiving a position request

(Position Reply) ........................36

Enabling automatic position

reply .......................................36

Sending your own position

(Position Send) ..........................37

Putting the radio into standby ....37

Disabling automatic channel

switching ....................................38

Table of Contents

E-3

Table of Contents (Cont'd)

List of Tables

Table 1 - Terms used in this

manual ............................................5

Table 2 - Rear panel .......................7

Table 3 - Front panel ......................8

Table 4 - Microphone button

connector ........................................9

Table 5 - Normal mode status

messages .....................................12

Table 6 - Character and text entry

order .............................................29

Table 7 - Receive log ...................35

Table 8 - Common GPS receiver and

connections ..................................45

Table 9 - Radio specifications ......54

Table 10 - Channel by type of

message .......................................56

Table 11 - USA Channel Frequencies

and Channel Tag ..........................57

Table 12 - Canadian Channel

Frequencies and Channel Tag ......59

Table 13 - International Channel

Frequencies and Channel Tag ......61

Table 14 - Weather Channel

Frequencies and Channel Tag ......63

Table 15 - CEA2009-S.A.M.E.

EVENT CODE ..............................63

Table 16 - NMEA Input .................66

Renaming Channels ...................39

Installing the Hardware ..............40

Mounting the radio ...................40

Connecting the radio ................42

Connecting accessories ...........44

Connecting to a GPS

receiver ..................................44

Configuring the GPS .............46

Connecting to a charplotter ...47

Connecting to an external

speaker ..................................47

Connecting to an external PA

speaker ..................................48

Using the PA feature ..............49

Maintenance and

Troubleshooting .........................50

Common questions .....................51

Engine Noise Suppression ..........53

Maritime radio services

operation ..................................53

Basic radio guidelines ..............53

Specifications .............................54

Channel by type of message ......56

Channel and frequencies ............57

Alert codes and event levels .......63

NMEA Operation .........................66

NMEA Input ...............................66

NMEA Output ............................66

Regulations and Safety Warnings 67

FCC information .......................67

Lead warning ............................67

Antenna Selection and

Installation ................................67

Three Year Limited Warranty .....68

Mounting Bracket Driling

Template ...........Inside Back Cover

E-4

Introduction

Features

Submersible Design

Complies with JIS7 water-resistant standards, which means the radio can

be submerged in 1 meter of water for 30 minutes without damage.

Large, dot matrix display

Advanced DSC Class D functions

Built-in PA feature

Channel select buttons on the microphone

Memory scan mode

Lets you save channels to memory and monitor them in quick succession.

Transmitter Power Level Select

Lets you boost the transmitter power from 1 watt to 25 watts for added

transmission distance.

Battery level display and tone

Sounds an alert tone if the battery voltage goes too high or too low.

Triple Watch Operation

Checks the Coast Guard Distress/Hailing channels 16 and 9 in the

background.

All marine VHF channels for the U.S., Canada, and international

waters

National Oceanic and Atmospheric Administration (NOAA) weather

channel watch

Sounds a warning tone when a hazard alert is issued for your area.

•

Manual overview

Conventions

This manual uses several different type styles to help you distinguish

between different parts of the radio:

• BOLD SMALL CAPITALS indicates an actual button or knob on the radio

or microphone.

• Upper and Lower case bold indicates a connector or label on the

radio.

• Italics indicate text on the display, such as menu options, prompts,

and conrmation messages.

Introduction

E-5

Introduction

DSC Digital Selective Calling. A VHF radio standard for

communicating among boats and sending automated

distress calls.

FIPS Federal Information Processing Standard. A set of

location codes roughly equivalent to your county

codes.

WX Weather radio

GPS Global Positioning System

NMEA National Marine Electronics Association. The

organization that governs standards for electronic

equipment used on boats. NMEA 0183 is the standard

for serial data communication used by GPS receivers.

MMSI Maritime Mobile Service Identity number. A unique,

nine-digit number that identies you and your boat

when making DSC calls. It is also used by the Coast

Guard if you send an automated distress call.

Station Any DSC radio, whether it’s operated on a boat, at a

marina, or by a shore station.

Table 1 - Terms used in the manual

Getting Started

E-6

What's included

VHF650 Radio

DC Power Cable

Accessory Cable

Mounting Bracket and

knobs

Mounting Hardware

Microphone Hanger and

Mounting Hardware

Spare Fuse 250V 6A

Getting Started

E-7

Getting Started

Parts of the radio

13.8V DC

ANTENNA

Antenna

connector

(SO238)

Heat sink

Power

connector

Accessory

connector

Table 2 - Rear panel connector functions

Connector Connects to For details, see

Antenna connector External VHF antenna with

a male PL259 (SO238)

connector and 50 Ω

impedance.

Minimum 4 ft, 3dB rated

antenna for sailboats, 8 ft, 6

dB rated for power boats.

Connecting the radio,

page 42.

Power connector Nominal 13.8 VDC power

supply with negative ground

(11.7 VDC to 14.3 VDC)

(Red wire +, black wire -).

Connecting the radio,

page 42.

Accessory connector GPS receiver, GPS

chartplotter, external speaker,

external PA speaker.

Connecting accessories,

page 44.

Getting Started

E-8

07A

1 Watt USA

Memory

Scanning Channels

01A,03A,05A,06,07A,08

LCD

display

SELECT/

1W/25W

button

CHANNEL UP &

DOWN buttons

VOLUME-PWR

(power) knob

(turn clockwise

to increase

volume)

Microphone

cord

16/9-TRI

(triple/

dual-watch)

button

WX-ALERT

(weather)

button

SCAN-MEM

(channel

memory)

button

MENU-PA

(public

address)

button

DISTRESS

button

SQUELCH knob

(turn clockwise

to decrease

channel noise)

Button Press to... Press and hold to...

SELECT-1W/25W

Choose an option on a menu. Change the transmit

power (see page 20).

CHANNEL UP

Move up one channel at a time. Move quickly up the

channels.

CHANNEL DOWN

Move down one channel at a time. Move quickly down the

channels.

16/9-TRI

1

st

press: Go to Channel 16.

2

nd

press: Go to Channel 9.

3

rd

press: Go back to the original

channel.

Go into Triple Watch or

Dual Watch mode (see

page 13).

DISTRESS

Select the nature of your distress

for a distress call.

Transmit a distress call.

Table 3 - Front panel button functions

E-9

Getting Started

Button Press to... Press and hold to...

WX-ALERT

Listen to the current weather

conditions in your area.

Monitor the weather

channels for alerts in any

area.

MENU-PA

Display the radio menu. Use the public address

(PA) function.

SCAN-MEM

Start scanning the channels saved

in memory.

Save a channel into

memory or remove a

channel from memory.

PUSH-

TO-TALK

button

16/9 TRI

(Triple/Dual-

Watch) button

+ (plus) button

(move up a channel)

- (minus) button

(move down a channel)

Table 4 - Microphone button functions

Button Press to... Press and hold to...

+ Move up one channel at a time. Move quickly up the

channels.

- Move down one channel at a time. Move quickly down the

channels.

16/9-TRI

1

st

press: Go to Channel 16.

2

nd

press: Go to Channel 9.

3

rd

press: Go back to the original

channel.

Go into Triple Watch or

Dual Watch mode (see

page 13).

PUSH TO TALK

Cancel scanning and stay on a

channel.

Talk on a channel.

Getting Started

E-10

Turning on the radio

Turn the VOLUME-PWR knob clockwise to turn on the radio. As it powers on,

the radio displays the user MMSI number; if there is no MMSI set, the radio

displays MMSI not entered.

When it powers on, the radio selects the last channel used.

Setting the UIC channel mode (USA/CAN/INT)

The radio comes preset to use the UIC channels assigned for the United

States. If you are operating in an area that uses Canadian or international

UIC channels, you will need to change the channel mode.

Press the MENU-PA button to display the menu, and choose the Setup

sub-menu.

Select USA/CAN/INT. The screen displays the UIC channel setup.

Highlight the channel mode you want to use: US (USA mode),

Canadian (Canada mode), or international (Intl mode).

Press the SELECT-1W/25W button. The radio activates the new channel

mode and exits the menu.

1.

2.

3.

4.

How It Works

The VHF650 has three basic modes of operation:

Operation mode What it does: Use it when: To turn it on/off:

Normal mode Monitors a single

marine radio

channel and lets

you talk on that

channel.

You want to talk to

another station on a

specic channel.

(default mode)

Scan mode Monitors all the

channels you save

into memory.

You have a small

group of channels

you use most often

and want to check

them for trafc.

Press the SCAN-

MEM button.

Weather mode Monitors the

selected NOAA

weather channel.

You want to hear

the current and

forecasted weather

in your area.

Press the WX-

ALERT button.

E-11

Getting Started

In addition to the three main operation modes, the VHF650 also provides

three different “watch” modes which you can activate during any of the three

basic modes. In the watch modes, the radio briey checks for activity on a

specic channel, then returns to its previous mode.

Watch mode What it does: Use it when: To turn it on/off:

Weather Alert

Watch

Checks for alerts

on the last weather

channel you

used every seven

seconds.

You want to be

made aware of

severe weather

conditions in your

area.

Press and hold the

WX-ALERT button

for two seconds.

Triple Watch Checks for activity

on channels 16

and 9 every two

seconds.

You want to monitor

a channel yet

maintain a watch on

channels 16 and 9.

Press and hold the

16/9-TRI button for

two seconds.

Dual Watch Checks for activity

on channel 16 every

two seconds.

You want to monitor

a channel yet

maintain a watch on

channel 16.

Change Triple

Watch to Dual

Watch in the setup

menu, then press

and hold the 16/9-

TRI button for two

seconds.

NOTE: You are required to monitor channel 16 whenever your boat is under-

way. You should have either Triple Watch or Dual Watch on at all times.

Normal mode operation

Normal mode monitors whatever channel you select, and you can transmit on

that channel also.

While using normal mode, the display lets you see the following information

(not all indicators will display at the same time):

25

Marine Operator

25 Watts USA

Memory Alert

GPS Data OK

Transmit power

(1 W or 25 W)

Current channel

is stored in

memory

Status messages

(see the status

message table)

Current

channel

number

Current channel

name (if the name

is too long, the

name line scrolls)

Channel mode

(USA, CANadian,

or INTernational)

Weather Alert

Watch on

Getting Started

E-12

Table 5 - Normal mode status messages

Message Meaning

GPS Data OK The radio is receiving valid GPS data.

Check GPS The radio is not receiving valid GPS data: check the GPS status screen and

the GPS connection.

Input Position The radio has been unable to receive valid GPS data for at least four hours;

it can no longer track your position. You need to manually input your position

(see Setting the GPS position manually on page 23).

Battery Low The battery voltage output is too low (below 11.2 VDC).

Battery High The battery voltage output is too high (above 14.8 VDC).

Triple Watch Triple Watch is turned on.

Dual Watch Dual Watch is turned on.

Using the radio in normal mode

• To transmit, press and hold the PUSH TO TALK button on the

microphone. Release the button when you are nished talking.

• For the best sound quality, hold the microphone about two inches from

your mouth while you’re talking.

• Press the CHANNEL UP button on the radio or the + button on the

microphone to move up one channel at a time. Press and hold either

button to scroll quickly up the channels.

• Press the CHANNEL DOWN button on the radio or the - button on the

microphone to move down one channel at a time. Press and hold

either button to scroll quickly down the channels.

• To change the transmit power, press and hold the SELECT-1W/25W

button for two seconds. The transmit power switches between 1 watt

and 25 watts each time you press and hold the SELECT-1W/25W button.

Normal mode with Weather Alert Watch

If you activate Weather Alert Watch

while operating in normal mode,

the radio checks the most recently-

used weather channel every seven

seconds. If it detects a weather

alert for your area, it will change the

channel to the last-used weather

channel. The radio will not check

the weather channel while you are actively transmitting; it waits until your

transmission is nished and then checks the weather channel.

Every 7 seconds, the

radio checks the most

recently-used weather

channel. with WX

Alert on

E-13

Getting Started

Press and hold the WX-ALERT button for two seconds to turn Weather Alert

Watch on or off.

09

16

09

16

09

16

Every 2 seconds, the radio

checks channels 9 & 16.

with Triple Watch on

Monitoring Channel 25

Normal mode with both Weather Alert and Triple/Dual Watch

wx

Every 7 seconds,

the radio checks the

most recently-used

weather channel.

with WX Alert on

09

16

09

16

09

16

Every 2 seconds, the radio

checks channels 9 & 16.

with Triple Watch on

Monitoring Channel 25

Press and hold the 16/9-TRI button (on the radio or the microphone) for two

seconds to turn Triple/Dual Watch on or off. (To change between Triple or

Dual Watch, see page 21.)

Normal mode with Triple and Dual Watch

If you activate Triple Watch while operating in normal mode, the radio checks

channels 16 and 9 every two seconds; with Dual Watch turned on, the radio

only checks channel 16. The radio will not check channels 16 or 9 while you

are actively transmitting; it waits until your transmission is nished and then

checks the channels.

You can activate Weather

Alert Watch and Triple/

Dual Watch at the same

time. The radio performs

both checks at their

scheduled time:

Getting Started

E-14

Scan mode

You can save channels into memory and then use scan mode to monitor

those channels. When the radio detects a signal on a channel, it pauses on

that channel as long as the signal is received; when the transmission stops,

the radio will continue scanning.

11

1008 1312

17

15

20

14

The radio scans about

5 channels in 1 second.

When it detects a signal, the radio stays on the

channel until you press the

CHANNEL UP

button or the

signal stops.

Resume scan

In scan mode, you can get the following information from the display (some

indicators will not always be displayed):

1 Watt USA

Memory

Scanning Channels

01A,03A,05A,06,07A,08

07

Transmit power

last used

Channel mode

(USA, CANadian,

or INTernational)

Current

channel being

scanned

Scan list (if the

text is too long,

the line scrolls)

All scanned

channels must

be in memory

Normal scan

mode or Triple/

Dual-watch on

Using the radio in scan mode

You cannot transmit while in scan mode.

You must have two or more channels in memory to start a scan.

To save a channel into memory, select the channel, then press and

hold the SCAN-MEM button for two seconds. Memory will show on the

display.

•

E-15

Getting Started

To remove a channel from memory, set the radio to that channel, then

press and hold the SCAN-MEM button for two seconds. Memory will no

longer show on the display.

To activate scan mode, press the SCAN-MEM button. Press the SCAN-

MEM button again to return to the previous mode.

When the radio automatically stops on a channel, press the CHANNEL

UP button to leave that channel and resume scanning.

To end the scan, press the microphone PUSH TO TALK button or the

SCAN-MEM button. The radio remains on the last scanned channel.

•

If you activate Weather Alert

Watch while operating in scan

mode, the radio checks the most

recently-used weather channel

every seven seconds, then

continues scanning the next

channel in memory:

Press and hold the WX-ALERT button for two

seconds to turn Weather Alert Watch on or

off.

Scan mode with Triple and Dual Watch

If you activate Triple Watch while

operating in scan mode, the radio

checks channels 16 and 9 every

two seconds, then goes on to

scan the next channel; with Dual

Watch turned on, the radio only

checks channel 16:

09 16

Every 2 seconds,

the radio checks

channels 9 & 16

then goes on to

the next channel.

with Triple Watch on

Memory Channel Scan

08 252417151413121110 20

Reversed 16 & 9

UJ-SW 20061215 #17

Press and hold the 16/9-TRI button (on

the radio or the microphone) for two

seconds to turn Triple/Dual Watch on or

off. (To change between Triple or Dual

Watch, see page 21.)

Scan mode with Weather Alert Watch

Getting Started

E-16

Scan mode with both Weather Alert and Triple/Dual Watch

You can activate Weather Alert Watch and Triple/Dual Watch at the same

time. The radio performs both checks at their scheduled time:

09 16

Every 2 seconds,

the radio checks

channels 9 & 16

then goes on to

the next channel.

with Triple Watch on

Every 7 seconds,

the radio checks

the last-used

weather channel,

then scans the

next channel.

wx

with WX Alert on

Memory Channel Scan

08 252417151413121110 20

Reversed 16 & 9

UJ-SW 20061215 #17

Weather mode

In cooperation with the FCC, NOAA also uses the weather channels to

alert you of other hazards besides weather (child abduction alerts, nuclear,

biological, etc.). In weather mode, the radio monitors one of the ten NOAA

weather channels. If any type of alert is received for your area, the radio

sounds an alert tone and displays the type of alert. In weather mode, the

display shows the following:

09

Hurricane Warning

Weather Band

Alert

Weather

mode is on

Current

channel

number

Type of alert (if the

text is too long, the

line scrolls)

Flashing: An alert

has been issued

Steady: Weather

Alert Watch is on

Using the radio in weather mode

You cannot transmit while in weather mode.

To enter weather mode, press the WX-ALERT button.

Weather mode can lter out alerts that do not affect your location if

the location code (FIPS code) of the alert is entered in your radio (see

page 21). If you have no FIPS codes programmed into your radio, the

radio will notify you of all alerts in any area.

•

E-17

Getting Started

Weather mode with Weather Alert Watch

Because weather mode already monitors the weather channels, you don’t

need Weather Alert Watch to check the weather channel every seven

seconds. If you activate Weather Alert Watch while operating in weather

mode, it operates as a type of “sleep mode”: the radio stays on the weather

channel and mutes the speaker. If an alert is detected for your area, the

radio sounds an alert tone and turns the speaker back on. This mode is very

useful when you are anchoring for the night but want to stay informed of any

hazards in your area.

Press and hold the WX-ALERT button for two seconds to turn Weather Alert

Watch on or off.

Weather mode with Triple and Dual Watch

If you activate Triple Watch while operating in weather mode, the radio

checks channels 16 and 9 every two seconds; with Dual Watch turned on, the

radio only checks channel 16.

To turn off the radio’s alert tone, press any button.

To cancel weather mode and return to the previous marine channel,

press the WX-ALERT button again.

•

Press and hold the 16/9-TRI button (on the radio or the microphone) for two

seconds to turn Triple/Dual Watch on or off. (To change between Triple or

Dual Watch, see page 21.)

09

16

09

16

09

16

Every 2 seconds, the radio checks

channel 9, then channel 16

with Triple Watch on

Monitoring Weather Channel WX08

La page est en cours de chargement...

West Marine VHF650 Le manuel du propriétaire

Ce manuel convient également à

West Marine VHF650 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents