Exodraft Xzense XTP Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
UK | Always read and save the instructions!
Your energy. Optimized.
3112012_Xzense XTP-sensor_UK | 210223
Instruction for safe use
XTP-sensor
Warning
The following symbols are used in the manual to point out the risk of danger or damage
to the product.
Violations of directions indicated by a hazard symbol are
associated with the risk of injury or damage to the equipment:
- Use the device correctly as specied by the manufacturer. If you have any questions
please contact your dealer
- Before servicing the unit, disconnect the power and ensure that no one can accidentally
reconnect
- Installation work should be carried out by competent persons and in accordance with
applicable national rules
- Follow the device’s instructions from the manufacturer and general safety instructions
- This unit must be connected to ground in the installation
Content of the package
1 pcs.pressure-controlled sensor (XTP-sensor).
1 pcs. cable
1 pcs. Installation guide/Manual
Warranty
All Exodraft products are covered by a 2-year guarantee as per European consumer rights
legislation. For some countries an extended period of guarantee may apply depending on either
national legislation or other clearly stipulated conditions. Customer complaints must be handled
by a specialised dealer or
wholesaler (preferably where the Exodraft product has been bought originally). An updated list
of Exodraft specialised dealers can be found on our website for the country in question.
Exodraft products must always be installed by properly qualied personnel. Exodraft reserves
the right to change these guidelines without prior notice.
Disposal
Electrical and electronic equipment (EEE) often contain materials, components and substances
that may harm the environment or be hazardous to your health. Products (WEEE) marked with
the ‘crossed-out wheeled bin’ symbol should be disposed of separately from other waste at the
end of its life. Though legislation may differ from country to country we strongly advise that
electrical and electronic waste is separated from other waste and disposed of according to
national legislation to protect the environment and personnel that may come into contact with
waste.
How to use this manual
This manual has been prepared based on the specific product and
contains relevant technical information and installations guides.
Accessories and spare parts are not covered by this manual.
Please refer to the individual manuals of these components.
This installation manual does not contain any system design documentation.
Failure to observe instructions marked with a danger symbol
may result in personal injury and/or damage to the product.
Errors and omissions excepted.
Application
exodraft’s Xzense XTP-sensor is a precision pressure transducer designed for
stoves. It can easily be installed with the exodraft wireless control system Xzense.
Setup - Mounting
The installation must be carried out by competent persons. The XTP-sensor makes it possible to
achieve a constant draft in the chimney, thereby ensuring optimum combustion during ring.
Xzense XTP-sensor must always be mounted with the hose connectors downwards (g. 1).
Material:
Title:
Rev. No.:Format:
Weight:
Draw. No.:
Sheet:
Uspecified tolerances acc.:
Scale:
Last updated by:
Date:
Created by:
Date:
Dimensions: AHL ahl
14-03-2019 14-03-2019
DS/EN 22768 m
XTP sensor
7501002
A
0,000 kg
1 of 2
1,5:1
A4
Metric
(g. 1)
Technical data
Working range 5 Pa - 150 Pa +/- 0,1% Full scale
Dimension (H x B x D) [mm] 75 x 85 x 25
Weight 120 g
Ingress protection IP20
Material Box: Black ABS - Lid: Black PC
Ambient temperature -25 oC - +50 oC
Storage temperature -25 oC - +50 oC
Input, supply 5 VDC - USB
Permitted overpressure 20000 Pa
Media Air and ue gases
When underpressure measurement, the pressure hose is mounted on the (-) stud. Overpressure
stud (+) must keep the black cap on.
Electrical connection
WARNING! Do not blow in the stud of an Xzense XTP-sensor!
ATTENTION! All installations must be performed by competent persons in
accordance with local laws and regulations.
Add device/pairing devices
Step Action Icon
1To add a device (XTP-sensor) to the
control panel, select the Add device
menu on the display. Add device
2
Already paired devices are displayed
screen with a trash can. To pair with a
new device, select a device with a link on
it. Here, select the device XTP-sensor. If
prompted for a password, use ”1 2 3 4” XTP-sensor
3
A dialog box appears and conrms that
the pairing has been done correctly.
Always make sure you have both power
control panel and XTP-sensor during
pairing.
Enhederne er nu parret.
OK
The devices are
now paired
4
To run with the XTP-sensor’s system
control, this must be selected below the
System control menu, located under the
Setup menu. System control
5Change system mangement from
Manual use to Pressure controlled use by
activating the ON function.
Pressure controlled
*Find more details and more information in the main Xzense manual. Can be found at www.exodraft-manuals.com
ATTENTION! Always have power/charging cable plugged in the XTP-sensor!
UK Conformity Assessed
Exodraft a/s
Industrivej 10
DK-5550 Langeskov
Hereby declares that the following products:
Were manufactured in conformity with the provisions of the following regulations:
The Supply of Machinery (Safety) Regulations 2008
Electrical Equipment (Safety) Regulations 2016
Electromagnetic Compatibility Regulations 2016
Radio Equipment Regulations 2017
Langeskov, 01-11-2022
Managing Director
Anders Haugaard
Declaration of Conformity
DK: EU-Overensstemmelseserklæring
GB: Declaration of Conformity
DE: EU-Konformitätserklärung
FR: Déclaration de conformité de l’Union Européenne
NO: EU-Samsvarserklæring
PL: EU Deklaracja zgodności
NL: EU-Conformiteits verklaring
SE: EU-Överensstämmelsedeklaration
FI: EU-Vaatimustenmukaisuusvakuutus
IS: ESS-Samræmisstaðfesting
IT: Dichiarazione di Conformità Unione Europea
Exodraft a/s
Industrivej 10
DK-5550 Langeskov
Erklærer på eget ansvar, at følgende produkter:
Hereby declares that the following products:
Erklärt hierdurch auf eigene Verantwortung, daß folgende Produkte:
Déclare, sous sa propre responsabilité, que les produits suivants:
Erklærer på eget ansvar at følgende produkter:
Niniejszym oświadcza, że następujące produkty:
Veklaart dat onderstaande producten:
Deklarerar på eget ansvar, att följande produkter:
Vastaa siltä, että seuraava tuote:
Staðfesti à eigin àbyrgð, að eftirfarandi vörur:
Dichiara con la presente che i seguenti prodotti:
Som er omfattet af denne erklæring, er i overensstemmelse med følgende
standarder:
Were manufactured in conformity with the provisions of the following stand-
ards:
Die von dieser Erklärung umfaßt sind, den folgenden Normen:
Auxquels s’applique cette déclaration sont en conformité avec les normes
ci-contre:
Som er omfattet av denne erklæring, er i samsvar med følgende standarder:
Zostały wyprodukowane zgodnie z warunkami określonymi w następujących
normach:
Zijn vervaardigd in overeenstemming met de voorschriften uit de hieronder
genoemde normen en standaards:
Som omfattas av denna deklaration, överensstämmer med följande standard-
er:
Jota tämä selvitys koskee, on seuraavien standardien mukainen:
Sem eru meðtalin i staðfestingu Pessari, eru i fullu samræmi við eftirtalda
staðla:
Sono stati fabbricati in conformità con le norme degli standard seguenti:
EN 60335-1, EN 60335-2-80, DS/EN ISO 12100: 2011
I.h.t bestemmelser i direktiv:
In accordance with
Entsprechen gemäß den Bestimmungen der folgenden Richtlinien:
Suivant les dispositions prévues aux directives:
I.h.t bestemmelser i direktiv:
Zgodnie z:
En voldoen aan de volgende richtlijnen:
Enligt bestämmelserna i följande direktiv:
Seuraavien direktiivien määräysten mukaan:
Med tilvisun til àkvarðana eftirlits:
In conformità con le direttive:
Maskindirektivet:
The Machinery Directive:
Richtlinie Maschinen:
Directive Machines:
Maskindirektivet:
Dyrektywą maszynową:
De machinerichtlijn:
Maskindirektivet
Konedirektiivi:
Vèlaeftirlitið:
Direttiva Macchinari:
2006/42/EF/-EEC/-EWG/-CEE
Lavspændingsdirektiv:
The Low Voltage Directive:
Niederspannungsrichtlinie:
Directive Basse Tension:
Lavspenningsdirektivet:
Dyrektywą Niskonapięciową
De laagspanningsrichtlijn:
Lågspänningsdirektivet:
Pienjännitedirektiivi:
Smáspennueftirlitið:
Direttiva Basso Voltaggio:
2014/35/EC
EMC-direktivet:
And the EMC Directive:
EMV-Richtlinie:
Directive Compatibilité Electromagnétique:
EMC-direktivet:
Dyrektywą EMC – kompatybilności elektromagnetycznej
En de EMC richtlijn:
EMC-direktivet:
EMC-direktiivi:
EMC-eftirlitið:
Direttiva Compatibilità Elettromagnetica:
2014/30/EC
Langeskov, 01-11-2022
Adm. direktør
Managing Director
Anders Haugaard
Algemeen directeur
Geschäftsführender Direktor
Président Directeur Général
Verkställande direktör
Toimitusjohtaja
Framkvemdastjori
Direttore Generale
XZENSE-XTP-01
XZENSE-XTP-01
-
1
Exodraft Xzense XTP Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
Documents connexes
-
Exodraft EFC16 Le manuel du propriétaire
-
-
-
-
-
-
-
-
-