Lenco KCR-200 Le manuel du propriétaire

Model KCR-200

User manual – Kitchen radio DAB+/FM with bluetooth, light and timer

Gebruikershandleiding – Keukenradio DAB+/FM met Bluetooth, verlichting en timer

Bedienungsanleitung – Küchenradio DAB+ / FM mit Bluetooth, Beleuchtung und Zeitschaltuhr

Mode d’emploi - Radio de cuisine DAB+/FM avec Bluetooth, éclairage et minuteur

Manual de usuario – Radio de cocina DAB+/FM con Bluetooth, iluminación y temporizador

2

Index

English .................................................................................................................................................................................... 3

Nederlands ........................................................................................................................................................................... 19

Deutsch ................................................................................................................................................................................ 35

Français ................................................................................................................................................................................ 51

Español ................................................................................................................................................................................. 67

Version: 1.0

3

English

KCR-200

CAUTION:

Usage of controls or adjustments or performance of procedures other than those specified herein may result in hazardous

radiation exposure.

This unit should not be adjusted or repaired by anyone except qualified service personnel.

PRECAUTIONS BEFORE USE

KEEP THESE INSTRUCTIONS IN MIND:

1. Do not use this device near water.

2. Clean only with a slightly damp cloth.

3. Do not cover or block any ventilation openings. When placing the device on a shelf, leave 5 cm (2”) free space around the

whole device.

4. Install in accordance with the supplied user manual.

5. * Don’t step on or pinch the power adaptor. Be very careful, particularly near the plugs and the cable’s exit point. Do not

place heavy items on the power adaptor, which may damage it. Keep the entire device out of children’s reach! When

playing with the power cable, they can seriously injure themselves.

6. * Unplug this device during lightning storms or when unused for a long period.

7. Keep the device away from heat sources such as radiators, heaters, stoves, candles and other heat-generating products or

naked flame.

8. Avoid using the device near strong magnetic fields.

9. Electrostatic discharge can disturb normal usage of this device. If so, simply reset and restart the device following the

instruction manual. During file transmission, please handle with care and operate in a static-free environment.

10. Warning! Never insert an object into the product through the vents or openings. High voltage flows through the product

and inserting an object can cause electric shock and/or short circuit internal parts. For the same reason, do not spill water

or liquid on the product.

11. Do not use in wet or moist areas such as bathrooms, steamy kitchens or near swimming pools.

12. Do not use this device when condensation may occur.

13. Although this device is manufactured with the utmost care and checked several times before leaving the factory, it is still

possible that problems may occur, as with all electrical appliances. If you notice smoke, an excessive build-up of heat or

any other unexpected phenomena, you should disconnect the plug from the main power socket immediately.

14. This device must operate on a power source as specified on the specification label. If you are not sure of the type of

power supply used in your home, consult your dealer or local power company.

15. * The socket outlet must be installed near the equipment and must be easily accessible.

16. * Do not overload ac outlets or extension cords. Overloading can cause fire or electric shock.

17. * Devices with class 1 construction should be connected to a main socket outlet with a protective earthed connection.

18. * Devices with class 2 construction do not require a earthed connection.

19. Keep away from rodents. Rodents enjoy biting on power cords.

20. * Always hold the plug when pulling it out of the main supply socket. Do not pull the power cord. This can cause a short

circuit.

21. Avoid placing the device on any surfaces that may be subject to vibrations or shocks.

22. To clean the device, use a soft dry cloth. Do not use solvents or petrol based fluids. To remove severe stains, you may use

a damp cloth with dilute detergent.

23. The supplier is not responsible for damage or lost data caused by malfunction, misuse, modification of the device or

battery replacement.

24. Do not interrupt the connection when the device is formatting or transferring files. Otherwise, data may be corrupted or

lost.

25. If the unit has USB playback function, the usb memory stick should be plugged into the unit directly. Don’t use an usb

extension cable because it can cause interference resulting in failing of data.

26. The apparatus shall not be exposed to dripping or splashing and make sure that no objects filled with liquids, such as

vases, are placed on or near the apparatus.

27. * To completely disconnect the power input, the mains plug of the apparatus shall be disconnected from the mains, as the

disconnect device is the mains plug of apparatus.

28. If the unit works with battery, Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

29. Attention should be drawn to the environmental aspects of battery disposal.

30. The apparatus can only be used in moderate extremely cold or climates warm environments should be avoided.

31. The rating label has been marked on the bottom or back panel of the apparatus.

32. This device is not intended for use by people (including children) with physical, sensory or mental disabilities, or a lack of

experience and knowledge, unless they’re under supervision or have received instructions about the correct use of the

device by the person who is responsible for their safety.

33. This product is intended for non-professional use only and not for commercial or industrial use.

4

34. Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position or by

failure to follow any other warning or precaution contained within this user manual will not be covered by warranty.

35. Never remove the casing of this apparatus.

36. Never place this apparatus on other electrical equipment.

37. Do not use or store this product in a place where it is subject to direct sunlight, heat, excessive dust or vibration.

38. Do not allow children access to plastic bags.

39. Only use attachments/accessories specified by the manufacturer.

40. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,

such as the power supply cord or the plug, when liquid has been spilled or objects have fallen into the apparatus, when

the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

41. *Do not use a damaged power cord or plug or a loose outlet. Doing so may result in fire or electric shock.

42. Prolonged exposure to loud sounds from personal music players may lead to temporary or permanent hearing loss.

ACCESSORIES

• Remote control

• Mounting kit (plastic plate + 2 sets of screws + 4 spacers + drill hole paper template)

Plastic plate

Spacer

Drill hole paper template

• Instruction manual

INSTALLATION

• Unpack all parts and remove protective material.

• *Do not connect the unit to the mains before checking the mains voltage and before all other connections have been

made.

* Those instructions are related only to products using power cable or AC power adaptor.

Warning

Do not ingest the battery, Chemical Burn Hazard.

This product contains a coin/button cell battery. *If corn/button cell battery is swallowed, it can severe internal

burns in just 2 hours and can lead to death.

Keep new and used batteries away from children.

If the battery compartment does not close securely, stop using the product and keep it away from children.

If you think batteries might have swallowed or placed inside any part of the body, seek immediate medical

attention.

Caution

Danger of explosion if battery is incorrect replaced.

Replace only with the same or equivalent type.

5

MOUNTING THE SET UNDER A CABINET

1. Decide the location to install the unit in the cabinet/shelf. Since the unit’s speakers are located on the left edge side and right

edge side respectively, it is recommended to reserve enough space to avoid blocking the sound.

2. Once the location is decided, you can use the drill hole paper template (supplied) as a guide hole location to drill the holes.

3. Install the plastic plate under the cabinet/shelf using the supplied spacers and screws, refer to the diagram below. Spacers are

optional to install as your preference. 2 sets of screws are provided for your selection. The longer screw set is usually used when

the spaces are used. Depends on the wooden board thickness, you may decide to use other suitable screw length by yourselves.

4. After the plastic plate is installed, slide the unit into it until it locks securely.

5. Due to its weight, the unit should be installed with great care. Make sure that the cabinet that is used is sturdy enough to support

the weight of the unit.

Note:

- To reduce the risk of fire, do not place the radio on any heating area or without the spacing.

- You can slide out the unit from the plastic plate and to be used as a standing kitchen radio.

6

FRONT PANEL

1. STANDBY / SOURCE

Press to turn on the unit. When it is turned on, press this button will toggle between DAB+, FM and Bluetooth mode. Press and

hold to turn off and go to Standby mode

2. LIGHT ON / OFF

Slide to turn on or turn off the downward lighting

3. NUMERIC BUTTONS

Press to direct tune to the stored preset FM channel

4. DISPLAY

5. SCAN / ST-MONO / PAIRING

DAB+: Press to start auto-scanning all available DAB+ stations

FM: Press to toggle between FM Stereo and Force Mono reception. Press and hold to start the full auto-scanning and store the

available FM channel

BT: Press and hold to disconnect the current connection and start to search another new Bluetooth device

6. / MIN.

DAB+: Press to display the previous station information

FM: Press to tune to different frequency. Press and hold to auto-scan the previous available channel

BT: Press to skip to the previous track

Timer Setup: Press to setup the minute setting

7. / SEC.

DAB+: Press to display the next station information

FM: Press to tune to different frequency. Press and hold to auto-scan the next available channel

BT: Press to skip to the next track

Timer Setup: Press to setup the second setting

8. / INFO/MENU / CLOCK SET

DAB+/FM: Press to display station information. Press and hold to enter the Menu for setting change

BT: Press to toggle between pause and resume playback operation

Standby mode: Press to enter clock setup operation

9. TIMER / ENTER / MEMORY

Press to enter the Timer Setup

DAB+/FM: During Menu operation, press to select the change setting. During non-Menu operation, press and hold to store the

preset channel as desired

10. – VOLUME +

Adjust the volume control

11. IR Receiver Window

7

REMOTE CONTROL

1.

STANDBY

2.

NUMERIC BUTTONS

3.

TUNE

4.

TUNE

5.

6.

INFO

SCAN

MENU

BT PREVIOUS

BT NEXT

BT PLAY/PAUSE

7.

TIMER

MIN.

SEC.

8.

9

10

11

12

13

14

15

16

17

VOLUME +

VOLUME –

MUTE

CH+

CH-

ST / MONO

MEMORY / ENTER

PAIRING

SLEEP

CLOCK SET

SOURCE

Remote Control Battery Installation

A CR2025 battery is already installed in the remote control unit. Before using, pull out the battery insulation sheet as shown below.

8

To replace a new battery, please refer to the figure shown below. When inserting a battery, be sure to do so in the proper direction.

• If the remote control conflicts with other devices, the operation will be affected.

• Do not simultaneously press buttons on the unit and the remote control.

• Avoid using two remote controls at the same time as it will cause a malfunction.

• Use only CR-2025 size batteries.

• If there is battery leakage, clean the remote control thoroughly before replacing batteries.

• Do not short two terminals of the batteries. Dispose old batteries in a suitable place.

CR2025 battery

Battery case

Pull out the battery case

Push in according to this direction

9

INSTALLING THE BATTERIES FOR CLOCK BACKUP

The clock will be maintained during a power failure by installing 2 x AAA / LR03 batteries (not supplied). Once the power is restored,

check the clock to make sure it is accurate and set it again if necessary.

INSTALLING THE BATTERIES

1. Open the battery compartment at the bottom of the unit by pressing on the catch and removing the cover.

2. Insert 2 x AAA / LR03 batteries (not supplied), preferably alkaline batteries, into the battery compartment following the polarity as

shown on the diagram inside the compartment.

3. Replace the battery compartment cover.

CONNECTING TO THE POWER SUPPLY

Plug the AC power cable into the AC wall socket.

BASIC OPERATION

Press the STANDBY button to turn on the unit. To turn off, press and hold the STANDBY button again.

Alternatively press the STANDBY button on the remote control to turn on or turn off the unit.

DAB+ / FM / BT

When the unit is turned on, press the SOURCE button to toggle between DAB+, FM and Bluetooth mode.

Volume Control

Press the VOLUME + / - buttons to change the volume.

Adjusting the Antenna

The antenna wire at the rear panel of the unit should be fully extended to ensure a good DAB+/FM reception. Alter the antenna position

for the best reception.

DAB+ OPERATION

The first time the DAB+ mode is selected, it will automatically scan for available DAB+ stations. Wait until the scanning has finished.

The display will show the scanning progress. After scanning it will tune to the first station.

Auto Scan

1. Turn on the unit in DAB+ mode.

2. Press the SCAN button to start auto-scanning the available stations.

Manual Scan

1. Turn on the unit in DAB+ mode.

2. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

3. Press the or button (the TUNE / TUNE button on the remote control) until “Manual tune” is displayed and then

press the ENTER button.

4. Press the or button (the TUNE / TUNE button on the remote control) to select the desired channel (5A-13F).

5. Press the ENTER button to confirm.

6. To select another channel (5A-13F), press the or button (the TUNE / TUNE button on the remote control) and

then press the ENTER button to confirm.

7. To quit manual scan, press the MENU button.

Tuning

Press the or button (the TUNE / TUNE button on the remote control) to display the information of the next station.

Then press the ENTER button to tune to this station within a few seconds.

Number of stations found

Progress bar

10

Storing DAB+ Presets

You can save up to 20 DAB+ stations.

1. Tune to the station you wish to store.

2. Press and hold the MEMORY button on the unit (the MEMORY button on the remote control). Preset channel number is displayed.

3. Press the or button on the unit (the TUNE / TUNE button on the remote control) to a preset number that you

want to store. Then press the MEMORY button to save.

Storing DAB+ Presets (Through Menu Operation)

You can save up to 20 FM presets.

1. Tune to the station you wish to store.

2. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu

operation.

3. Press the or button on the unit (the or button on the remote control) until “Preset Store” is displayed and then

press ENTER button.

4. Press the or button on the unit (the TUNE / TUNE button on the remote control) to a preset number that you

want to store. Then press the ENTER button to save.

Recall Stored DAB+ Presets

Press the CH- or CH+ button directly tune to the preset channel.

To directly recall the preset channel by using the numeric buttons on the unit, press the numeric buttons [1], [2], …, [5].

For example when the button [3] is pressed, the display shows “P03” and wait for a while it will tune to the preset 3.

Or when press and hold the button [3 / (8)] button until the display shows “P08” and wait for a while, it will tune to the preset 8.

Or when press the button [1] button and followed by pressing the button [2], the display will show “P12” and after a while it will tune

to the preset 12.

Or when press the button [1] button and followed by press and hold the button [3 / (8)], the display will show “P18” and after a while

it will tune to the preset 18.

Alternatively you can use the remote control numeric buttons to directly recall the preset channel, press the numeric buttons [1], [2], …,

[9], [0].

For example when the button [3] is pressed, the display shows “P03” and wait for a while it will tune to the preset 3.

Or when press the button [8] until the display shows “P08” and wait for a while, it will tune to the preset 8.

Or when press the button [1] and followed by pressing the button [2], the display will show “P12” and after a while it will tune to the

preset 12.

Or when press the button [1] and followed by press the button [8], the display will show “P18” and after a while it will tune to the

preset 18.

Recall Stored DAB+ Presets (Through Menu Operation)

1. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu

operation.

2. Press the or button on the unit (the or button on the remote control) until “Preset Recall” is displayed and then

press ENTER button.

3. Press the or button on the unit (the TUNE / TUNE button on the remote control) to a preset number that you

want to recall. Then press the ENTER button to tune to the preset station number.

Note:

- The antenna wire at the rear panel of the unit should be fully extended to ensure a good reception. Alter the antenna position for

the best reception.

11

Displaying DAB+ Station Information

There are several types of information as listed below. To change the display information, press the INFO / MENU button (the INFO

button on the remote control) repeatedly.

1. Radio Text scrolling

Shows music titles or program details provided by the broadcaster

2. Signal Bar

Transmission signal level. The more the rectangles are filled, the stronger the signal is received. The unfilled rectangle is the

threshold level where the signal strength received should exceed this threshold. To improve the reception, adjust the antenna

position.

3. Program Type (PTY)

Type of program provided by the broadcaster

4. Multiplex Name

Displays name of multiplex to which the current station belongs

5. Frequency

Current channel number and frequency

6. Signal Error Rate

Shows the error rate. The larger this value, the more errors it receives. To improve the reception, adjust the antenna position.

7. Audio Bit Rate

This is the current channel audio Bitrate

8. Time

Displays the current time provided by the radio station

9. Date

Displays the current date provided by the radio station

OTHER DAB+ MENU OPERATIONS

Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

Then press the or button (the or button on the remote control) for different options as described below.

Dynamic Range Control (DRC)

DRC can make quieter sounds easier to hear when the unit is used in a noisy environment. The DRC level of a broadcast is set by the

broadcaster and transmitted with the service. Changing the DRC value on your unit enables you to apply a scaling factor to this level.

There are three levels of compression:

DRC high:

Maximum compression as sent with the transmitted service

DRC low:

Set to 1/2 that of the sent transmitted service

DRC off:

No compression

1. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

2. Press the or button (the or button on the remote control) until “DRC” is displayed and then press the ENTER

button.

3. Press the or button (the or button on the remote control) to select the DRC value and then press the ENTER to

confirm.

4. Press the INFO / MENU button on the unit (the MENU button on the remote control) to exit the menu control.

Note:

- Not all DAB+ broadcasts are able to use DRC function. If the broadcast does not support DRC then the DRC setting in the unit will

have no effect.

- After you have adjusted the DRC level the sound may be louder.

Prune

This function removes inactive stations.

1. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

2. Press the or button (the or button on the remote control) until “Prune” is displayed and then press the ENTER

button.

3. Press the or button (the or button on the remote control) to select “<Yes>” and then press the ENTER button to

prune the unit.

4. Press the INFO / MENU button on the unit (the MENU button on the remote control) to exit the menu control.

12

“S” for Stereo

“M: for Mono

FM RADIO OPERATION

Auto Scan

1. Turn on the unit in FM mode.

2. Press and hold the SCAN button on the unit (or press the SCAN button on the remote control) to start auto-scanning and saving

the available channels (max. 20 storage).

Manual Scan

1. Press the or button on the unit (the TUNE / TUNE button on the remote control) repeatedly to manually tune to

a different frequency.

2. Press and hold the or button on the unit (the TUNE / TUNE button on the remote control) to automatically search

to the next available channel.

Storing FM Presets

You can save up to 20 FM presets.

1. Tune to the station you wish to store.

2. Press and hold the MEMORY button on the unit (the MEMORY button on the remote control). Preset Store number is displayed.

3. Press the or button on the unit (the TUNE / TUNE button on the remote control) to a preset number that you

want to store. Then press the MEMORY button to save.

Storing FM Presets (Through Menu Operation)

You can save up to 20 FM presets.

1. Tune to the station you wish to store.

2. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu

operation.

3. Press the or button on the unit (the or button on the remote control) until “Preset Store” is displayed and then

press ENTER button.

4. Press the or button on the unit (the TUNE / TUNE button on the remote control) to a preset number that you

want to store. Then press the ENTER button to save.

Recall Stored FM Presets

Press the CH- / CH+ button on the remote control to tune to different preset channel.

To directly recall the preset channel by using the numeric buttons on the unit, press the numeric buttons [1], [2], …, [5].

For example when the button [3] is pressed, the display shows “P03” and wait for a while it will tune to the preset 3.

Or when press and hold the button [3 / (8)] button until the display shows “P08” and wait for a while, it will tune to the preset 8.

Or when press the button [1] button and followed by pressing the button [2], the display will show “P12” and after a while it will tune

to the preset 12.

Or when press the button [1] button and followed by press and hold the button [3 / (8)], the display will show “P18” and after a while

it will tune to the preset 18.

Alternatively you can use the remote control numeric buttons to directly recall the preset channel, press the numeric buttons [1], [2], …,

[9], [0].

For example when the button [3] is pressed, the display shows “P03” and wait for a while it will tune to the preset 3.

Or when press the button [8] until the display shows “P08” and wait for a while, it will tune to the preset 8.

Or when press the button [1] and followed by pressing the button [2], the display will show “P12” and after a while it will tune to the

preset 12.

Or when press the button [1] and followed by press the button [8], the display will show “P18” and after a while it will tune to the

preset 18.

Preset channel number

13

“S” for Stereo

“M: for Mono

Recall Stored FM Presets (Through Menu Operation)

1. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu

operation.

2. Press the or button on the unit (the or button on the remote control) until “Preset Recall” is displayed and then

press ENTER button.

3. Press the or button on the unit (the TUNE / TUNE button on the remote control) to a preset number that you

want to recall. Then press the ENTER button to tune to the preset station number.

Stereo / Force Mono Selection

When receiving a Stereo FM radio channel, press the ST/MONO button will switch between stereo audio and force mono audio.

Note:

- The antenna wire at the rear panel of the unit should be fully extended to ensure a good reception. Alter the antenna position for

the best reception.

Displaying FM Station Information

There are several types of information as listed below. To change the display information, press the INFO / MENU button (the INFO

button on the remote control) repeatedly.

1. Radio Text

Scrolling text which shows information on music titles or program details provided by the radio station

2. Program Type (PTY)

Type of program provided by the broadcaster

3. Frequency

Current channel frequency

4. Audio Type

Stereo or Mono

5. Time

Displays the current time provided by the radio station

6. Date

Displays the current date provided by the radio station

OTHER FM MENU OPERATION

Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

Then press the or button for different options as described below.

Scan Setting

1. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

2. Press the or button until “Scan setting” is displayed and then press the ENTER button.

3. Press the or button to toggle between “All stations” or “Strong station” selections and then press the ENTER button

confirm. When “All stations” is selected, all stations will be detected during FM scanning even if the radio station is noisy. When

the “Strong station” is selected, only the strong stations are detected. Scanning will ignore the noisy stations.

4. The next time doing a FM scan the unit will search for the stations based on this confirmed setting.

Audio Setting

1. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

2. Press the or button until “Audio setting” is displayed and then press the ENTER button.

3. Press the or button to toggle between “Stereo allowed” or “Forced mono” selection and then press the ENTER button

confirm.

14

BLUETOOTH AUDIO

Please follow the pairing instructions below to link the unit to your Bluetooth device.

1. Press the SOURCE button to enter the Bluetooth mode. The display will flash. It will start searching and the display keeps flashing.

2. If the unit has never been paired with a Bluetooth device before or cannot find the last paired device, the display will keep flashing.

Turn on the Bluetooth function of your device and enable the search until “Lenco KCR-200” is found. Select “Lenco KCR-200” on

the Bluetooth device to make connection. Enter the pass code “0000” if required.

3. After successfully paired the display will become steady without flashing.

4. You can now start playing music from your smartphone wirelessly to the speaker.

5. You can press the PLAY / PAUSE button to pause or resume the playback.

6. You can press the or button to skip to the previous or next song.

 Press and hold the PAIRING button will disconnect the current connection and start to search another new Bluetooth device.

SLEEP FUNCTION

1. When the unit is switched on, press the SLEEP button on the remote control repeatedly to select the sleep duration in minutes

among sleep off, 05, 10, 15, 30, 45 and 90

2. During the sleep timer count down, there is a character “S” shown on the display right hand side.

3. When the sleep timer is zero, the unit will be turned off automatically.

4. To cancel the sleep function, press and hold the STANDBY button on the unit (or press the STANDBY button on the remote control)

to turn off. Alternatively press the SLEEP button repeatedly to “sleep off”.

CLOCK & DATE SETUP

1. Turn off the unit in Standby mode.

2. Press the CLOCK SET button to enter the setup.

3. Minute digit display will flash. Press the or button to set the minute. Press the CLOCK SET button to confirm.

4. Second digit display will flash. Press the or button to set the second. Press the CLOCK SET button to confirm.

5. Day digit display will flash. Press the or button to set the day. Press the CLOCK SET button to confirm.

6. Month digit display will flash. Press the or button to set the month. Press the CLOCK SET button to confirm.

7. Year digit display will flash. Press the or button to set the year. Press the CLOCK SET button to finish the clock & date

setup.

Note:

- The time, date and year set may automatically be overridden by the DAB+ or FM station real time information.

TIMER SETUP

1. Press the TIMER button to enter the Timer setup.

2. Press the MIN. and SEC button to adjust the minute and second respectively. Press the TIMER button.

3. Press the or button to enable (on) or disable (OFF) the timer setup. When it is set to on, press the TIMER button to finish the

timer setup. It will start to count down.

4. During the timer count down, there is a flashing character “T” shown on the display right hand side.

5. During the timer count down, press the TIMER button will stop the count down. The remaining count down time will be displayed.

After a while, the display will resume to normal operation display. “T” is still shown on the display but without flashing meaning it

is pause. Further pressing the TIMER button will resume the count down. “T” will continue flashing.

6. To cancel the count down, press the TIMER button once to pause the count down. Then during the remaining count down time is

displayed, press and hold the TIMER button will cancel the count down.

7. When the timer count down is finished, the alarm buzzer will be turned on. Press TIMER button will stop the buzzer.

TIMER Indicator

SLEEP Indicator

15

TIME SETUP

This setup allows you to setup 4 different display modes. They are set Time/Date, time update mode, set 12/24 hour display and set

date format.

Set 12/24 Hour Display

1. Turn on the unit in DAB mode or FM mode.

2. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

3. Press the or button until “System” is displayed and then press the ENTER button.

4. Press the or button until “Time” is displayed and then press the ENTER button.

5. Press the or button until “Set 12/24 hour” is displayed and then press the ENTER button.

6. Press the or button to toggle between 12 or 24 hour display. Select your desired and then press the ENTER button to

confirm.

7. Press the INFO / MENU button on the unit (the MENU button on the remote control) once to re-enter the previous menu level. Or

press it repeatedly to exit the menu control.

Set Date Format

1. Turn on the unit in DAB mode or FM mode.

2. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

3. Press the or button until “System” is displayed and then press the ENTER button.

4. Press the or button until “Time” is displayed and then press the ENTER button.

5. Press the or button until “Set date format” is displayed and then press the ENTER button.

6. Press the or button to toggle between “DD-MM-YYYY” or “MM-DD-YYYY” date display. Select your desired and then press

the ENTER button to confirm.

7. Press the INFO / MENU button on the unit (the MENU button on the remote control) once to re-enter the previous menu level. Or

press it repeatedly to exit the menu control.

Auto Update

1. Turn on the unit in DAB mode or FM mode.

2. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

3. Press the or button until “System” is displayed and then press the ENTER button.

4. Press the or button until “Time” is displayed and then press the ENTER button.

5. Press the or button until “Auto update” is displayed and then press the ENTER button.

6. Press the or button to change between

 “Update from Any”: Time/Date will be updated by either DAB or FM broadcast

 “Update from DAB”: Time/Date will be updated by DAB broadcast only

 “Update from FM”: Time/Date will be updated by FM broadcast only

 “No update”: Time/Date will never be updated by broadcast

7. Select your desired and then press the ENTER button to confirm.

8. Press the INFO / MENU button on the unit (the MENU button on the remote control) once to re-enter the previous menu level. Or

press it repeatedly to exit the menu control.

16

Set Time/Date

1. Turn on the unit in DAB mode or FM mode.

2. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

3. Press the or button until “System” is displayed and then press the ENTER button.

4. Press the or button until “Time” is displayed and then press the ENTER button.

5. Press the or button until “Set Time/Date” is displayed and then press the ENTER button.

6. Hour digits will be flashed. Press the or button to set hour and then press the ENTER button.

7. Minute digits will be flashed. Press the or button to set the minute and then press the ENTER button.

8. If 12 hour display is set, “AM or “PM” will be flashed. Press the or button to set AM or PM and then press the ENTER

button to confirm.

9. Day digits will be flashed. Press the or button to set the day and then press the ENTER button.

10. Month digits will be flashed. Press the or button to set the month and then press the ENTER button.

11. Year digits will be flashed. Press the or button to set the year and then press the ENTER button to complete the setup.

12. Press the INFO / MENU button on the unit (the MENU button on the remote control) once to re-enter the previous menu level. Or

press it repeatedly to exit the menu control.

Note:

- The time, date and year set may automatically be overridden by the DAB+ or FM station real time information.

LANGUAGE SETUP

You can set the unit’s language.

1. Turn on the unit in DAB+ mode or FM mode.

2. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

3. Press the or button until “System” is displayed and then press the ENTER button.

4. Press the or button until “Language” is displayed and then press the ENTER button.

5. Press the or button to toggle between different languages. Select your desired language and then press the ENTER button

to confirm.

6. Press the INFO / MENU button on the unit (the MENU button on the remote control) once to re-enter the previous menu level. Or

press it repeatedly to exit the menu control.

SOFTWARE VERSION CHECK

You can check the unit software version.

1. Turn on the unit in DAB+ mode or FM mode.

2. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

3. Press the or button until “System” is displayed and then press the ENTER button.

4. Press the or button until “SW version” is displayed and then press the ENTER button to show the software version number.

5. Press the INFO / MENU button on the unit (the MENU button on the remote control) once to re-enter the previous menu level. Or

press it repeatedly to exit the menu control.

FACTORY RESET

This function resets the unit to the original factory settings.

1. Turn on the unit in DAB+ mode or FM mode.

2. Press and hold the INFO / MENU button on the unit (or press the MENU button on the remote control) to access the menu control.

3. Press the or button until “System” is displayed and then press the ENTER button.

4. Press the or button until “Factory Reset” is displayed and then press the ENTER button.

5. Press the or button until “Yes” is displayed and then press the ENTER button to reset the unit.

6. After reset, the until will be started automatically.

LIGHT ON / OFF

Slide to LIGHT ON / OFF switch on the front panel to turn on or turn off the downward lighting.

ENERGY SAVING

Due to ErP stage 2 requirement and protect the environment, the unit will turn off to the standby mode automatically once no music

has been playing in Bluetooth mode around 15 minutes.

When the unit is power off due to ErP, you can press the STANDBY button to turn on the unit again.

17

Trouble Shooting

No power

• Ensure that the mains cable is connected securely.

• Ensure that the unit is switched on.

The remote control does not function

• Use the remote control near to the unit.

• Point the remote control at the remote control sensor on the unit.

• Replace the batteries in the remote control with new ones.

• Remove any obstacles between the remote control and the unit.

The unit does not respond when pressing any buttons.

• In some situations the unit may freeze during use. To reset the unit, pull the plug from the mains socket, wait a few seconds and

then plug it in again.

No sound output

• Make sure that the unit is not muted.

I can’t find the Bluetooth name of this unit on my Bluetooth device for Bluetooth pairing

• Ensure that the unit is switched on.

• Ensure that the Bluetooth function is activated on your Bluetooth device.

• The unit has a Bluetooth function that can receive a signal within 10 meters.

DAB+/FM reception

• Ensure the antenna wire at the rear panel should be extended fully to improve the DAB+/FM reception.

• Electrical interference in your home can cause poor reception. Move the unit away from them (especially those with motors and

transformers).

Interferences in Speakers

• Check that you have not left a mobile phone near the unit.

18

TECHNICAL SPECIFICATIONS

DAB+ radio frequency range

FM radio frequency range

Bluetooth frequency range

174.928-239.2 MHz

87.5-108 MHz

2.402-2.480 GHz

AC power input

230V~, 50Hz

Power consumption

13 W

Speaker output power

Bluetooth version

Battery backup (not included)

Remote control battery (Included)

2 x 1 W RMS

V4.1

AAA / LR03 batteries x 2pcs

CR2025 x 1pcs

Unit dimension (L x D x H)

240 x 150 x 62 mm

Total weight

0.9 kg

• The specification presents only as a reference. The value of weight and size are approximation.

• Our product is improved ceaselessly and the specification and function may be changed without prior notice.

GUARANTEE

Lenco offers service and warranty in accordance with the European law, which means that in case of repairs (both during and after the

warranty period) you should contact your local dealer.

Important note: It is not possible to send products that need repairs to Lenco directly.

Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires.

This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be voided.

DISCLAIMER

Updates to Firmware and/or hardware components are made regularly. Therefore some of the instruction, specifications and pictures

in this documentation may differ slightly from your particular situation. All items described in this guide for illustration purposes only

and may not apply to a particular situation. No legal right or entitlements may be obtained from the description made in this manual.

DISPOSAL OF THE OLD DEVICE

This symbol indicates that the relevant electrical product or battery should not be disposed of as general

household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose

them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries.

In so doing, you will help to conserve natural resources and improve standards of environmental protection in

treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).

SERVICE

For more information and helpdesk support, please visit www.lenco.com

Lenco Benelux BV, Thermiekstraat 1a, 6361 HB Nuth, The Netherlands.

19

Nederlands

KCR-200

LET OP:

Gebruik van bedieningen of afstellingen of uitvoer van procedures anders dan gespecificeerd in deze documentatie kan leiden

tot blootstelling aan schadelijke straling.

Dit apparaat dient uitsluitend te worden aangepast of gerepareerd door gekwalificeerd onderhoudspersoneel.

VOORZORGSMAATREGELEN VOOR GEBRUIK

ONTHOUD DE VOLGENDE INSTRUCTIES:

1. Gebruik dit apparaat niet in de buurt van water.

2. Reinig het uitsluitend met een licht vochtige doek.

3. Bedek of blokkeer de ventilatieopeningen niet. Wanneer u het apparaat op een schap plaatst, dient u 5 cm (2”) vrije

ruimte rondom het gehele apparaat te behouden.

4. Installeer het product volgens de meegeleverde gebruikershandleiding.

5. *Nooit op de stroomadapter stappen of deze indrukken. Wees voornamelijk voorzichtig in de buurt van de stekkers en het

punt waar de kabel uit het apparaat komt. Plaats geen zware voorwerpen op de stroomadapter, om beschadiging ervan te

voorkomen. Houd het gehele apparaat buiten bereik van kinderen! Wanneer kinderen met de voedingskabel spelen,

kunnen zij ernstig letsel oplopen.

6. *Haal de stekker uit het stopcontact tijdens onweer of wanneer u deze langere tijd niet gebruikt.

7. Houd het apparaat uit de buurt van hittebronnen, zoals radiatoren, verwarmingen, kachels, kaarsen en andere

hittegenererende producten of open vuur.

8. Gebruik dit apparaat niet in de buurt van krachtige magnetische velden.

9. Elektrostatische ontlading kan normaal gebruik van dit apparaat verstoren. U hoeft het apparaat in dit geval slechts te

resetten en opnieuw op te starten volgens de gebruikershandleiding. Wees voorzichtig tijdens bestandsoverdracht en

gebruik het product in een omgeving zonder statische interferentie.

10. Waarschuwing! Steek nooit een voorwerp via de ventilatie- of andere openingen in het product. Er is hoogspanning in het

product aanwezig en als u er een object insteekt, kan dat een elektrische schok veroorzaken en/of kortsluiting in de

interne onderdelen. Mors om dezelfde reden geen water of vloeistof op het product.

11. Gebruik het toestel niet in vochtige ruimtes, zoals badkamers, stomende keukens of in de buurt van zwembaden.

12. Gebruik dit apparaat niet wanneer condensatie kan optreden.

13. Alhoewel dit apparaat met grote zorg gefabriceerd en verschillende keren geïnspecteerd is voordat het de fabriek verlaat,

is het nog steeds mogelijk dat er problemen optreden, zoals met alle elektrische apparaten. Als u rook, een overmatige

hitteontwikkeling of enig ander onverwacht verschijnsel opmerkt, moet u onmiddellijk de stekker van het netsnoer uit het

stopcontact halen.

14. Dit apparaat moet werken op een voedingsbron, zoals aangegeven op het specificatieplaatje. Als u twijfelt over het type

voeding dat gebruikt wordt in uw huis, raadpleeg dan uw dealer of plaatselijk energiebedrijf.

15. *Het stopcontact moet in de buurt van de apparatuur zijn geïnstalleerd en eenvoudig te bereiken zijn.

16. *Overbelast stopcontacten of verlengsnoeren niet. Overbelasting kan brand of een elektrische schok veroorzaken.

17. *Apparaten met een Klasse 1 structuur dienen te worden aangesloten op een stopcontact met een beschermende

aardverbinding.

18. *Apparaten met een Klasse 2 structuur vereisen geen aardverbinding.

19. Houd het uit de buurt van knaagdieren. Knaagdieren knauwen graag aan voedingskabels.

20. *Houd altijd de stekker vast wanneer u deze uit het stopcontact trekt. Trek nooit aan de voedingskabel. Dit kan tot een

kortsluiting leiden.

21. Vermijd om het toestel te plaatsen op een ondergrond die blootgesteld kan worden aan trillingen of schokken.

22. Gebruik een zacht, droog doekje om het apparaat te reinigen. Gebruik geen oplosmiddelen of op benzine gebaseerde

vloeistoffen. U kunt een vochtig doekje met verdund schoonmaakmiddel gebruiken om hardnekkige vlekken te

verwijderen.

23. De leverancier is niet verantwoordelijk voor schade of verloren gegevens veroorzaakt door storing, misbruik, modificatie

van het apparaat of batterijvervanging.

24. Onderbreek nooit de verbinding wanneer het apparaat formatteert of bestanden overdraagt. De gegevens kunnen anders

corrupt of verloren raken.

25. Indien het apparaat een USB-afspeelfunctie heeft, moet de USB-geheugenstick rechtstreeks op het apparaat worden

aangesloten. Gebruik geen USB-verlengkabel, omdat die kan leiden tot storingen met foutieve gegevens als gevolg.

26. Het apparaat mag niet worden blootgesteld aan druppels of spatten en zorg ervoor dat er geen met vloeistof gevulde

voorwerpen, zoals vazen, op of nabij het apparaat zijn geplaatst.

27. *Om de verbinding met de stroomaansluiting volledig te verbreken, moet de stekker van het apparaat uit het stopcontact

worden gehaald, omdat de stekker van het apparaat de hoofdschakelaar is.

28. Indien het apparaat op batterijen kan werken, dan mogen de batterijen niet aan overmatige hitte, zoals zonlicht, open

vuur e.d. worden blootgesteld.

29. Aandacht voor het milieu is nodig bij het verwijderen van de batterijen.

30. Het apparaat kan alleen worden gebruikt in gematigde klimaten. Extreem koude of warme omgevingen moeten worden

vermeden.

20

31. Het nominale specificatielabel is te vinden op het paneel aan de onder- of achterkant van het apparaat.

32. Dit apparaat is niet bestemd voor gebruik door mensen (inclusief kinderen) met fysieke, zintuiglijke of geestelijke

gebreken of gebrek aan kennis en ervaring, tenzij zij onder toezicht staan of instructies hebben over het juiste gebruik van

het apparaat hebben gekregen van de persoon die verantwoordelijk is voor hun veiligheid.

33. Dit product is alleen voor niet-professioneel gebruik bedoeld en niet voor commercieel of industrieel gebruik.

34. Verzeker u ervan dat het apparaat in een stabiele positie staat opgesteld. Schade, veroorzaakt door het gebruik van dit

product in een onstabiele positie, of door het niet naleven van waarschuwingen of voorzorgsmaatregelen genoemd in

deze handleiding, valt niet onder de garantie.

35. Verwijder nooit de behuizing van dit apparaat.

36. Plaats dit apparaat nooit op andere elektrische apparatuur.

37. Dit product niet gebruiken of opslaan op plaatsen waar het wordt blootgesteld aan direct zonlicht, hitte, buitensporig veel

stof of trillingen.

38. Geef kinderen geen gelegenheid in aanraking met plastic zakken te komen.

39. Gebruik uitsluitend uitbreidingen/accessoires gespecificeerd door de fabrikant.

40. Laat alle reparaties over aan gekwalificeerd onderhoudspersoneel. Onderhoud is vereist als het toestel hoe dan ook is

beschadigd, zoals bijvoorbeeld het netsnoer of de stekker, wanneer er vloeistof of een voorwerp in het apparaat is

terechtgekomen, wanneer het apparaat is blootgesteld aan regen of vocht, als het niet normaal werkt of is gevallen.

41. *Gebruik nooit een beschadigde voedingskabel of stekker of een los stopcontact. Dit vormt namelijk een risico op brand

of elektrische schokken.

42. Langdurige blootstelling aan luid geluid van persoonlijke muziekspelers kan leiden tot tijdelijke of permanente

gehoorbeschadiging.

ACCESSOIRES

• Afstandsbediening

• Montagekit (kunststof plaat + 2 sets schroeven + 4 tussenringen + papieren sjabloon voor boorgaten)

Kunststof plaat

Tussenring

Papieren sjabloon voor boorgaten

• Gebruiksaanwijzing

INSTALLATIE

• Pak alle onderdelen uit en verwijder de beschermende materialen.

• *Sluit het apparaat niet aan op het stopcontact, voordat u de netspanning hebt gecontroleerd en voordat alle andere

aansluitingen zijn gemaakt.

* Deze instructies hebben alleen betrekking op producten met een netsnoer of AC-voedingsadapter.

Waarschuwing

Batterij niet inslikken, risico op chemische brandwonden.

Dit product bevat een knoopcelbatterij. *Als de knoopcelbatterij wordt ingeslikt, kan dit binnen 2 uur ernstige

inwendige brandwonden veroorzaken en tot de dood leiden.

Houd nieuwe en gebruikte batterijen buiten bereik van kinderen.

Als de batterijhouder niet goed kan worden gesloten, dient u het product niet meer te gebruiken en buiten

bereik van kinderen te houden.

Als u denkt dat batterijen zijn ingeslikt of binnenin een willekeurig lichaamsdeel terecht zijn gekomen, dient u

onmiddellijk medische hulp te zoeken.

La page charge ...

Lenco KCR-200 Le manuel du propriétaire

Ce manuel convient également à

Lenco KCR-200 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents