Dremel Idea Builder 3D40 Mode d'emploi

1-844-4DRML3D (1-844-437-6533) www.dremel.com

P.O. Box 081126 Racine, WI 53408-1126

3D40

Idea Builder

Operating/Safety Instructions

Consignes d’utilisation/de sécurité

Instrucciones de funcionamiento y seguridad

For English Version

See page 2

Version française

Voir page 37

Versión en español

Ver la página 73

IMPORTANT

Read Before Using

IMPORTANT

Lire avant usage

IMPORTANTE

Leer antes de usar

Call Toll Free for Consumer Information & Service Locations

Pour obtenir des informations et les adresses de nos centres de service après-vente, appelez ce numéro gratuit

Llame gratis para obtener información para el consumidor y ubicaciones de servicio

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 1

2

Safety Symbols....................................................................................2

General Safety Warnings..................................................................3-5

Additional Safety Warnings..................................................................5

Symbols ...............................................................................................5

Dremel Remote and Mobile Services ..................................................5

FCC Compliance .................................................................................6

Information on Intellectual Property .....................................................6

Specifications.......................................................................................7

Resources............................................................................................8

Glossary of Terms.............................................................................8-9

Introduction ........................................................................................10

Kit Contents .......................................................................................10

Unpacking ..........................................................................................11

Getting To Know Your Dremel 3D40.............................................12,13

Touch Screen................................................................................14-20

Initial Setup ........................................................................................21

Getting Started with Your Dremel 3D App .........................................22

Print Studio Software Overview .........................................................23

Getting Ready to Build..................................................................24-28

Building.........................................................................................29-30

Removing Your Object .......................................................................31

Maintenance ......................................................................................32

Troubleshooting .................................................................................33

Best Practices....................................................................................34

Dremel

®

Consumer Limited Warranty ................................................35

Table of Contents

Safety Symbols

The definitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

!

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 2

3

Work Area Safety

Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

Do not operate Dremel 3D40 in the

presence of flammable liquids, gases or

dust. Dremel 3D40 creates high

temperatures which may ignite the dust or

fumes.

Store idle 3D40 out of reach of children

and other untrained persons. Injury can

occur in hands of untrained users.

Electrical Safety

Always use the Dremel 3D40 with a

properly grounded outlet. Do not modify

Dremel 3D40 plug. Improper grounding and

modified plugs increase risk of electric shock.

Do not use Dremel 3D40 in damp or wet

locations. Do not expose Dremel 3D40 to

rain. Presence of moisture increases risk of

electric shock.

Do not abuse the cord. Never use the cord

for pulling or unplugging the Dremel 3D40.

Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or

entangled cords increase the risk of electric

shock.

Avoid using this product during an

electric storm. There may be a remote risk

of a power surge from lightning that may

result in electric shock hazard.

In case of emergency unplug Dremel 3D40

from outlet.

Personal Safety

Stay alert, watch what you are doing and

use common sense when operating a

Dremel 3D40. Do not use Dremel 3D40

while you are tired or under the influence

of drugs, alcohol or medication. A moment

of inattention while operating Dremel 3D40

may result in personal injury.

Use personal protective equipment. The

use of protective equipment such as heat

resistant gloves and safety glasses will

reduce the risk of personal injuries.

Dress properly. Do not wear loose clothing

or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose

clothes, jewelry or long hair can be caught in

moving parts.

Dremel 3D40 Use and Care

Before every use check Dremel 3D40 for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the Dremel 3D40’s

operation. If damage is suspected have

the Dremel 3D40 repaired by authorized

Dremel service center before use. Use of

Dremel 3D40 when damaged may result in

poor quality of object creation, further

equipment damage, property damage or

personal injury.

Do not touch the extruder tip during

Dremel 3D40 operation or until it has

cooled down to at least 60°C (140°F).

Contact with the extruder tip during or after

operation before tip has cooled may result in

personal injury.

Set up the Dremel 3D40 in a well-ventilated

area. Place Dremel 3D40 printer on flat

nonflammable surface and away from

flammable materal. Provide at least 8

inches of unobstructed spacing around

Dremel 3D40. Dremel 3D40 melts plastic

during building. Plastic odors emitted during

Dremel 3D40 operation may irritate eyes and

airways. Locating Dremel 3D40 close to

surrounding objects prevents proper

ventilation.

Do not reach inside the Dremel 3D40 while

it is in operation. Contact with Dremel 3D40

moving parts during operation may result in

poor build quality, equipment damage or

personal injury.

Always monitor the Dremel 3D40 during

operation. Use of Dremel 3D40 by persons

unfamiliar with these warnings and

instructions may result in equipment or

property damage and personal injury.

Read all instructions in this manual and familiarize yourself with the

Dremel 3D40 before setup and use. Failure to comply with the warnings

and instructions may result in fire, equipment damage, property damage, or personal

injury.

READ ALL INSTRUCTIONS

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

!

WARNING

General Safety Warnings

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 3

4

Use only DREMEL filament. Use of filament

n

ot authorized by Dremel may result in

equipment and property damage.

Ensure small objects created by Dremel

3D40 are not accessible to young children.

Small objects are potential choking hazards

for young children.

Do not create illegal or inappropriate

objects using Dremel 3D40.

Do not use Dremel 3D40 to create objects

intended for use with candles, liquid fuels,

and other heat sources. Plastic may melt

when exposed to fire or other heat sources.

Such use of objects created by Dremel 3D40

may result in fire, property damage and

personal injury.

Do not use Dremel 3D40 to create objects

intended for food or drink applications

such as preparation, decoration, storage,

or consumption. Such use of objects

created by Dremel 3D40 may result in illness

or personal injury.

Do not use Dremel 3D40 to create objects

intended with use with electrical

components or housings of electrical

components. PLA plastic is not suitable for

electrical applications. Such use of objects

created by Dremel 3D40 may result in

property damage and personal injury.

Do not put plastic objects in or around

your mouth. PLA plastic is not suitable for

food or drink preparation and food utensils.

Such use of objects created by Dremel 3D40

may result in illness or personal injury.

Do not use Dremel 3D40 to create objects

intended for chemical storage. PLA plastic

is not suitable for chemical storage. Such use

of objects created by Dremel 3D40 may result

in property damage and personal injury.

Do not modify Dremel 3D40 or alter factory

settings. Modifications may result in

equipment and property damage, and

personal injury.

Do not expose Dremel 3D40 to

temperatures exceeding 70°C (158°F).

Dremel 3D40 may become damaged.

Dremel 3D40 is intended to operate in

temperature between 16-29° C (60 - 85° F).

Do not move or bump Dremel 3D40 or the

extruder during operation. The object may

build incorrectly.

Do not change filament spool unless the

building process is completed, stopped,

or paused. Changing the filament during

building will cancel the object and may

d

amage the extruder.

Do not pull the filament out. Doing so may

damage the extruder.

Use extra care not to damage the extruder

tip when clearing debris. Dremel 3D40 will

not work properly with damaged extruder tip

and will require replacement.

Before every build make sure that the

build platform is covered with Dremel

specified build tape. Use of improper build

tape may result in equipment damage and

poor object build quality.

Be aware of your body position when

using hand tools to remove objects from

the build platform. Sudden tool slip and

improper body position during object removal

from the build platform may result in personal

injury.

Avoid scratching the build platform when

removing objects. Scratches in the build

platform will result in improper object creation.

Do not drop the build platform. Tempered

glass plate may break and result in personal

injury.

Do not remove tempered glass plate from

plastic holder. Contact with tempered glass

plate edge may result in personal injury.

Do not twist or bend the build platform

while removing objects. Tempered glass

plate may separate from plastic holder and

result in personal injury.

Dremel is not responsible for structural

integrity or utility of objects created using

Dremel 3D40. Structural models created by

inexperienced designers may result in

property damage and personal injury.

Service

Always unplug Dremel 3D40 from its

power before performing any service

procedures. Failure to do so may result in

personal injury and equipment damage.

Have your Dremel 3D40 serviced only by

an authorized Dremel service center using

only Dremel replacement parts. This will

ensure that proper operation and safety of

Dremel 3D40 is maintained.

Use only Dremel approved materials and

components. Use of filament or 3D objects

other than Dremel

®

approved filament and

genuine Dremel

®

components may void

warranty.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 4

5

This product may contain or discharge chemicals known to the State of

California to cause cancer and birth defects or other reproductive harm.

!

WARNING

Additional Safety Warnings

SAVE THESE INSTRUCTIONS

Dremel remote and mobile services provide you

with information and services regarding your

Dremel 3D products. The type of information

provided by Dremel remote and mobile services

may change from time to time. All product

information and services are provided for your

convenience, “As is” and “As Available”.

Dremel does not guarantee that the information

or services will be available, accurate, or

reliable, or that product information or services

will provide safety in your home. You use all

product information, services, and products at

your discretion and risk. The product

information and services are not intended as a

substitute for direct means of obtaining

information.

Network connectivity requires an access point

and high speed internet connection. Internet

service provider charges may apply.

Mobile printing requires a compatible mobile

device and data plan. Carrier charges may

apply.

Dremel Remote and Mobile Services

Symbols

IMPORTANT: Some of the following symbols may be used on your 3D40. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

Symbol Designation / Explanation

V Volts (voltage)

A Amperes (current)

Hz Hertz (frequency, cycles per second)

ø

Diameter

0 Off position

Alternating current (type or a characteristic of current)

Hot surface hazard symbol. Contact may cause burn. Allow to cool before

servicing.

Alerts user to read manual.

This symbol designates that this tool is listed by Underwriters Laboratories,

to United States and Canadian Standards.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 5

6

FCC COMPLIANCE

NOTE: This equipment has been tested and

found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or

television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct

the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

Changes and Modifications not expressly

approved by the manufacturer or registrant of

this equipment can void your authority to

operate this equipment under Federal

Communications Commission’s rules.

INDUSTRY CANADA (IC)

This device complies with Industry Canada’s

licence-exempt RSSs. Operation is subject to

the following two conditions:

(1) This device may not cause interference;

and

(2) This device must accept any interference,

including interference that may cause

undesired operation of the device.

The device meets the exemption from the

routine evaluation limits in section 2.5 of RSS

102 and compliance with RSS-102 RF

exposure, users can obtain Canadian

information on RF exposure and compliance.

FCC and IC Compliance

Information on Intellectual Property

The Dremel 3D40 is intended for 3D printing

objects from digital files that you create or

own, or have the right to print using the

Dremel 3D40. When making objects using

the Dremel 3D40, it is your responsibility to

ensure that you do not infringe any third

party intellectual property rights or violate

any applicable laws or regulations, such as

U.S. or foreign intellectual property laws.

The Dremel 3D40 may not be used to make

objects protected by intellectual property

rights owned by third parties without such

third parties’ permission. Using the Dremel

3D40 to do any of the following may require

the permission of third parties: to make a

duplicate or facsimile (in whole or in part) of

any object not created by you, to make an

object from a digital file you do not own, or to

make an object from a scan of a physical

object that you did not create. It is your

responsibility to obtain such permission. In

some cases, you may not be able to obtain

such permission. Where such permission

cannot be obtained, you should not 3D print

such object, or you do so at your own risk.

You may not modify, reverse engineer,

decompile, or disassemble the Dremel 3D40

or its software or firmware, except as

permitted by applicable law.

If you use the Dremel 3D40 in any way other

than as recommended and described in

these Operating/Safety Instructions, you do

so at your own risk. Using the Dremel 3D40

to make objects that infringe any intellectual

property rights owned by third parties could

result in civil or criminal prosecution and

penalties, and you could be liable for money

damages, fines, or imprisonment.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 6

7

Specifications

BUILDING

Extruder: Single extrusion

E

xtruder temperature: Up to 230°C (397°F)

Operating Interface: 3.5” full color IPS touch

screen

Maximum Build Volume: 10” x 6” x 6.7”

(255mm x 155mm x 170mm)

Layer Thickness: 4 mil | 0.004 inches 100

microns | 0.10 mm

Filament Colors: See Dremel3D.com for

color choices

Internal Storage: 4GB

External Storage: USB Flash Drive

WEIGHT & DIMENSIONS

Weight (without spool): 16kg (35lbs)

Dimensions: 20.25” x 16” x 15.9” (515mm x

406mm x 394mm)

FILAMENT

ONLY works with Dremel 1.75mm filament

FILAMENT STORAGE

All polymers degrade with time. Do not

unpack until filament is needed. Filament

should be stored at room temperature:

16-29° C (60-85° F) and in dry conditions.

SOFTWARE

Dremel 3D40 comes with complimentary

Autodesk Print Studio software for Windows

and Mac OSX. This application converts your

3D digital files into buildable files.

SUPPORTED OPERATING SYSTEMS

• Apple

®

Mac

®

OS

®

X v10.9 or later

(

Mavericks)

• Microsoft

®

Windows

®

8.1

• Microsoft

®

Windows

®

7 SP1

MINIMUM SYSTEM SPECIFICATIONS

• CPU: 64-bit processor (32-bit not

supported)

• Memory: 3 GB RAM (4 GB or more

recommended)

• Disk space: ~2 GB free disk space for

installation

• Display card: 1,024 MB GDDR RAM or

more. Microsoft

®

Direct3D

®

11 capable

graphics card or higher

• Pointing device: Three-button mouse

ELECTRICAL REQUIREMENTS

3D40 input rating: 100-240V, 47-60Hz,

0.8A-1.8A

OPERATING ENVIRONMENT

Room Temperature: 16-29° C (60 - 85° F)

Level workspace

Dry workspace environment

16” (406mm)

20.25” (515mm) 15.5” (394mm)

WALL

8” (203mm)

8” (203mm)8” (203mm)

14” (356mm)

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 7

8

Glossary of Terms

Resources

Resource Description Location

Quick Start

Guide

Provides illustrated walkthrough of

how to un-box your 3D40 and start

building out of the box.

Printed version of the Quick Start

Guide is located in the rectangular

component carton. It is also

available on www.dremel3d.com

Dremel 3D

Website

Provides the latest 3D40 software,

product information, customer support,

and 3D model and project downloads.

www.dremel3d.com

Dremel 3D

Customer

Support

Contact Dremel for product support,

maintenance, and service.

1-844-4DRML3D

(1-844-437-6533)

www.dremel3d.com

Print Studio

Software

Allows you to upload, edit, and build

3D files.

Installed from www.dremel3d.com

or from USB flash drive provided

with the Dremel 3D40.

Term Definition

Build Platform The flat surface used by your Dremel 3D40 to build objects. The build platform is

comprised of a tempered glass plate with a plastic holder.

Build Platform Clip Clip located at the front of the build platform base that is used to secure the build platform

in place.

Build Tape Adhesive tape that improves the consistency of your objects and helps them stick to the

build plate surface.

Build Volume The three dimensional (3D) amount of space that an object will use once it is completed.

Your Dremel 3D40 has a maximum build volume which means that objects with a larger

build volume cannot be built unless they are resized or broken into sub-objects.

Door Your Dremel 3D40 has a door located on the front panel. This allows for easy access to

the build platform, extruder, filament, and your objects. This door is made with a

transparent material so you can monitor the progress of your objects while keeping the

build environment stable.

Ethernet Port A local area wired networking technology that allow electronic devices to communicate.

Extruder An assembly that uses gears to pull filament through the extruder intake, heat the filament

to the build temperature, and push the heated filament out of the extruder tip.

Extruder Fan A fan used to cool the outer assembly of the extruder and gear motor.

Extruder Fan Baffle A plastic piece that directs air from the extruder fan onto the build platform to assist in

cooling the active build.

Extruder Intake An opening located at the top of the extruder where filament is inserted for building.

Extruder Lever A lever located on the side of the extruder that is used to loosen the grip of the extruder

gear motor.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 8

9

Extruder Tip A nozzle located at the bottom of the extruder where heated filament is forced out for

building.

Filament A threadlike strand of plastic material.

Filament Guide Tube A plastic piece that guides the filament from the filament spool through a passage in

the outer housing of your Dremel 3D40.

Filament Jam Sensor A sensor in the extruder that pauses your printer if filament stops extruding properly.

Filament Runout Sensor A sensor in the extruder intake that pauses your printer if it runs out of filament

during a build.

Filament Spool A cylindrical piece on which a long strand of filament is wound for storage and

continuous use.

.G3Drem/.G4Drem A buildable file format compatible with your Dremel 3D40.

Leveling Knobs Knobs located under the build platform base that are used to create proper spacing

between the extruder tip and the build platform.

Leveling Sensor A sensor that detects the height of the build platform and assists in proper leveling.

Lid Your Dremel 3D40 has a pivoting lid on the top. This allows for more access to the

build platform, extruder, filament, and objects when necessary.

Needle Nose Pliers Common tool used to hold small objects and to grab excess material that may be too

hot to touch directly.

OBJ File A common digital file format used in a wide range of 3D model software. This file is

created in 3rd party 3D software or downloaded from Dremel3D.com.

Object Removal Tool A tool used to separate your objects from the build platform.

PLA A bioplastic derived from renewable resources such as corn starch.

Spool Holder A plastic piece located to the left of the build platform inside your Dremel 3D40 build

area that is designed to hold a filament spool.

Spool Door A removable door which locks the filament spool to the spool holder.

Stepper Motor A brushless DC electric motor used to drive the guide rails and extruder gears.

.STL File A common digital file format used in a wide range of 3D model software. This file is

created in 3rd party 3D software or downloaded from Dremel3D.com.

Touch Screen Full color display that is touch activated. It allows you to monitor your Dremel 3D40

and objects while also providing commands directly to your Dremel 3D40 without the

use of a computer.

USB Flash Drive A portable memory card used on a wide array of devices.

WIFI A local area wireless networking technology that allow electronic devices to

communicate.

X-Axis Guide Rails A set of rails on either side of the extruder that allow a stepper motor to move the

extruder to the left or right side of the build area.

Y-Axis Guide Rails A set of rails on either side of the build area that allow a stepper motor to move the

extruder to the front or back of the build area.

Z-Axis Guide Rails A set of rails located at the back of the build area that allow a stepper motor to move

the build platform up or down.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 9

10

Kit Contents*

Introduction

Welcome to the world of Dremel 3D. Our

mission is to mentor you through the 3D

b

uilding process and share best practices for

bringing your ideas to life.

3D building is a process that will involve

experimentation and persistence. Thankfully,

the Dremel experts are here to make your

job easier with online tips and live support.

Dremel 3D40 brings new functionality to

Dremel3D such as network connectivity and

remote printing. To get started with 3D40

follow the initial setup routine on the touch

screen to connect and register the printer.

You can create a user profile by either going

to www.dremel3d.com or by downloading the

D

remel3D mobile application on your

compatible mobile device. Your profile gives

you access to high-quality models, support

and software downloads, and remote printing

services powered by Spark. Once setup and

registration is complete you are ready to start

building.

1

-

8

4

-

4

D

R

M

L

3

D

(

1

-

8

4

-

4

3

7

-

6

5

3

)

w

.

d

r

e

m

e

l

.

c

o

m

P

.

O

.

B

ox

081126

R

ac

i

ne,

W

I

53408-

1126

3

D

4

0

I

d

e

a

B

u

i

l

d

e

r

O

pe

r

a

t

in

g

/

S

a

f

e

t

y

I

n

st

r

uc

t

io

n

s

C

o

n

s

i

gn

e

s

d

’

u

t

i

l

i

s

a

t

i

o

n

/

d

e

s

é

c

u

r

i

t

é

I

n

s

t

r

u

c

i

o

n

e

s

d

e

fu

n

c

i

o

n

a

m

i

e

n

t

o

y

s

e

gu

r

i

d

a

d

For

Engl

i

s

h

V

er

s

i

on

S

ee

page

2

V

er

s

i

on

f

r

anç

ai

s

e

V

oi

r

page

16

V

er

s

i

ón

en

es

pañol

V

er

l

a

pági

na

30

I

M

P

O

R

T

A

N

T

R

ead

B

ef

or

e

U

s

i

ng

I

M

P

O

R

T

A

N

T

Li

r

e

av

ant

us

age

I

M

P

O

R

T

A

N

TE

Leer

ant

es

de

us

ar

C

a

l

T

o

l

F

r

e

f

o

r

C

o

n

s

u

me

r

I

n

f

o

r

ma

tio

n

&

S

e

r

v

ic

e

L

o

c

a

tio

n

s

Po

u

r

o

b

t

e

n

i

r

d

e

s

i

n

f

o

r

m

a

t

i

o

n

s

e

t

l

e

s

a

d

r

e

s

e

s

d

e

n

o

s

c

e

n

t

r

e

s

d

e

s

e

r

v

i

c

e

a

p

r

è

s

-

v

e

n

t

e

,

a

p

e

l

e

z

c

e

n

u

m

é

r

o

g

r

a

t

u

i

t

Ll

a

m

e

g

r

a

t

i

s

p

a

r

a

o

b

t

e

n

e

r

i

n

f

o

r

m

a

c

i

ó

n

p

a

r

a

e

l

c

o

n

su

m

i

d

o

r

y

u

b

i

c

a

c

i

o

n

e

s

d

e

se

r

v

i

c

i

o

3

D40 Quick Start Guide

WARNINGWARNING

R

EAD ALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE

D

REMEL 3D20 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS

M

AY RESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.

Dremel 3D40 Instruction Manual Quick Start Guide

Filament Spool** Power Cable USB Cable

Build Tape Object Removal Tool USB Flash Drive

Unclog Tool

*Quantities may vary depending on kit.

**Do not store in moist or hot environment.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 10

11

1. Place box on table, cut tape, and open.

2. Remove top insert.

3. Remove 3D40 and place on table.

4. Open lid and remove top insert.

5. Raise build plate by lifting from both sides.

6. Open door and remove middle insert.

7. Remove bottom insert.

Tip: Keep packaging for future transportation

and storage.

Unpacking

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 11

12

Getting To Know Your 3D40

1. Lid

2. Extruder

3. Z-Axis Guide rail

4. Door

5. Gripping Handles

6. USB A Port

7. Leveling Knobs

8. Build Platform Clip

9. Touch Screen

10. Build Platform

11. Filament Spool Holder

12. Filament Spool

13. Y-Axis Guide Rail

14. Stepper motor

15. Filament Guide Tube

16. Extruder Lever

17. Filament Guide Clip

18. Extruder Intake

19. Extruder Fan

20. Ribbon Cable

21. X-Axis Guide Rail

22. Leveling Sensor

23. Extruder Tip

24. Power Switch

25. USB B Port

26. Ethernet Port

27. Nameplate

28. Power Input

1

4

9

6

12

10

2

11

5

8

7

3

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 12

13

M

o

d

e

l

3

D

4

0

F

0

1

3

D

4

0

1

0

V

–

2

4

0

V

~

4

7

–

6

3

H

z

0

.

8

–

1

.

8

A

Ø

1

.

7

5

m

(

0

.

0

6

9

"

)

L

I

S

T

E

D

3

D

P

R

I

N

T

E

R

E

4

6

9

3

1

U

1

S

N

K

O

N

I

J

N

E

N

B

E

R

G

6

0

,

4

8

2

5

B

D

B

R

E

D

A

-

N

L

M

/

Y

X

D

r

e

m

e

l

M

o

u

n

t

P

r

o

s

p

e

c

t

,

I

L

M

a

d

e

i

n

C

h

i

n

a

14 15 16 20

21

23

24 25 26 28

22

19

27

13

17

18

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 13

14

Touch Screen

Using your Dremel 3D40 without a computer is easy with the onboard software and full color

touch screen.

Before building your model we want to familiarize you with the touch screen menu structure

and options.

Observe all provided warnings and safety instructions when using the

Dremel 3D40. Failure to do so may result in fire, equipment damage, property

damage or personal injury.

!

WARNING

BUILD

Tap to select a 3D model and begin build process.

(see page 28 for detailed build instructions)

BUILD MENU

Tap Printer, USB Flash Drive, or Print Queue to

choose the destination of your desired file.

MODEL MENU

Tap to select the desired model or use arrows to

scroll through pages to find your model.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 14

15

FILE DETAILS

BUILD – Tap to begin build process.

DELETE – Tap to remove model file from on-printer

storage or USB flash drive.

COPY TO PRINTER – From USB flash drive, tap to

copy model file to on-printer storage.

BUILD STATUS

STOP – Tap to cancel the current build process.

PAUSE/PLAY – Tap to pause or resume the current

build process. Pause will allow you to access the

filament button.

CHANGE FILAMENT – Tap to change filament

during the current build process to add more

filament or change colors.

PRINT QUEUE MENU

BUILD – Tap to view details of next build.

DELETE – Tap to remove next build from queue.

PRINT QUEUE MODEL DETAILS

BUILD – Tap to begin build process.

DELETE – Tap to remove model file from queue.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 15

16

FILAMENT

Tap to begin heating and start filament load/change

process. (See page 24 for instructions on filament

load/change process)

LEVEL

Tap to begin build platform leveling process. (see

page 27 for instructions on leveling the build

platform)

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 16

17

TOOLS

Tap to access the following individual printer

functions and settings.

SERVICE

Tap to enter service menu to see customer service

contact information.

NETWORK

Tap to enter Network menu to connect or disconnect

WiFi and Set Proxy.

CONNECT WIFI – Tap to connect to WiFi.

DISCONNECT WIFI – Tap to turn Wifi off.

SET PROXY – Tap to set manual proxy.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 17

18

JOG MODE

Tap to display options to move extruder and build

platform along the X, Y, and Z-axis.

CALIBRATE

Tap to move extruder and build platform to zero

position.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 18

19

SETTINGS

LANGUAGE – Tap to pick alternate menu language.

DISPLAY – Tap to customize cabinet LEDs or main

menu hotkeys.

Z-AXIS OFFSET – Used to calibrate build plate

height during assembly.

SOUNDS – Tap to turn 3D40 sounds On/Off.

DEMO MODE – Tap to turn retail demo mode

On/Off.

FACTORY RESET – Tap to remove all information

stored on 3D40 and return it to factory defaults.

GET NEW TOKEN – Tap to release current token

and get a new token when connected to Wifi or

Ethernet.

CHECK FOR UPDATES – Tap to check for new

firmware version when connected to Wifi or

Ethernet.

PREHEAT

Tap to automatically begin preheating the extruder

for building or removing excess debris.

PURGE – Once extruder is hot, tap to manually

extrude filament.

STOP/START – Tap to stop or start preheating.

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 19

20

ABOUT

Tap to see 3D40 information such as firmware

version, usage counter, printer status, MAC

address, and token.

!

Indicates that there is an error such as filament empty or door open.

Indicates that Ethernet is connected.

Indicates WiFi signal strength and if connected to WiFi symbol

will be blue.

Indicates that the extruder is cool.

Indicates that the extruder is warm.

Indicates that the extruder is hot.

Indicates that the printer is connected to Spark 3D printing services

and that it can receive remote commands.

Touch Screen Icons

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 20

La page charge ...

Dremel Idea Builder 3D40 Mode d'emploi

Ce manuel convient également à

Dremel Idea Builder 3D40 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents