Power Fist 8901043 Le manuel du propriétaire

Taper
Le manuel du propriétaire
V4.0 8901043
Please read and understand all instructions before use. Retain this manual for
future reference.
User Manual
3.5 cu. ft Electric
Cement Mixer
8901043 3.5 cu. ft Electric Cement Mixer V4.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Voltage 120V AC / 60Hz
Motor Power 1/3 HP
Motor Speed 1400 RPM
Drum Capacity (Cu./Ft.) 3.5
Drum Speed 36 RPM
Rubber Wheels 10” (2)
Drum Rotation 360°
PACKAGING CONTENTS
Motor Box
Upper Drum
Crossbeam
Control Handle
Handle Plate
Rubber Seal
Wheel Bracket
Lower Drum
Support Bracket
Wheels (2)
Blades (2)
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection and
maintenance instructions.
3.5 cu. ft Electric
Cement Mixer
V4.0 3.5 cu. ft Electric Cement Mixer 8901043
Visit www.princessauto.com for more information 3
PERSONAL SAFETY
1. Stay alert, watch what you are doing, and use common sense when
operating the tool. Do not use the tool while you are tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating the tool may result in serious personal injury.
2. Dress properly. Do not wear loose clothing, dangling objects, or jewelry.
Keep your hair, clothing and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts. Air vents on
the tool often cover moving parts and should be avoided.
3. Wear the proper personal protective equipment when necessary. Use ANSI
Z87.1 compliant safety goggles (not safety glasses) with side shields, or
when needed, a face shield. Use a dust mask in dusty work conditions.
Also use non-skid safety shoes, hardhat, gloves, dust collection systems,
and hearing protection when appropriate. This applies to all persons in the
work area.
4. Do not overreach. Keep proper footing and balance at all times.
CEMENT MIXER USE AND CARE
1. Do not force the cement mixer. Products are safer and do a better job when
used in the manner for which they are designed. Plan your work and use
the correct product for the job.
2. Check for damaged parts before each use. Carefully check that the product
will operate properly and perform its intended function. Replace damaged
or worn parts immediately. Never operate the product with a damaged part.
3. Store the product when it is not in use. Store it in a dry, secure place out of
the reach of children. Inspect the tool for good working condition prior to
storage and before re-use.
4. Use only accessories that are recommended by the manufacturer for use
with your product. Accessories that may be suitable for one product may
create a risk of injury when used with another tool. Never use an accessory
that has a lower operating speed or operating pressure than the tool itself.
5. Keep guards in place and in working order. Never operate the product
without the guards in place.
8901043 3.5 cu. ft Electric Cement Mixer V4.0
4 For technical questions call 1-800-665-8685
SPECIFIC SAFETY PRECAUTIONS
1. To prevent serious injury or property damage, read and understand
owner’s manual before operating.
2. Always use the proper protective equipment, including ANSI Z87.1
compliant eye protection, heavy duty work gloves, and hearing protection.
3. Rotating Parts Hazard. Do not place tools, hoses, hands, arms, or any part
of the body inside the drum unless motor is off, and the power cord
unplugged.
4. Operate on a hard, level surface.
5. Do not leave the machine unattended while it is running.
6. Electrocution Hazard. Ensure that the mixer is properly grounded.
7. Do not plug or unplug the cord while standing in or around damp or wet
ground.
8. Do not operate the mixer in wet or damp areas or expose it to rain.
9. Turn power off and unplug before servicing.
10. Use only outdoor rated, grounded extension cords of the proper size.
11. Not for use by or around children.
IDENTIFICATION KEY
A. Motor box
B. Upper drum
C. Lower drum
D. Control handle
E. Crossbeam
F. Support bracket
G. Wheel bracket
V4.0 3.5 cu. ft Electric Cement Mixer 8901043
Visit www.princessauto.com for more information 5
ASSEMBLY & INSTALLATION
1. Place the Crossbeam (55)
into the Wheel Bracket (58)
so the bolt holes line up.
Fasten together using Hex
Bolts (57), Flat Washers
(10), and Hex Nuts (9). Set
the stand on its side for
easier assembly. See Figure
A.
2. Insert the Support Bracket (62) onto the Crossbeam (55) so the bolt holes
line up. Fasten together using Hex Bolts (57), Flat Washers (10), and Hex
Nuts (9). Tighten with a wrench until secure. Place the Crossbeam upright.
See Figure B.
Fig. B
Fig. A
8901043 3.5 cu. ft Electric Cement Mixer V4.0
6 For technical questions call 1-800-665-8685
3. To attach the Wheels
(60) to the Wheel
Bracket (58), slide a
Washer (59), Wheels,
and second Washer onto
the Bracket Axle. Insert
Cotter Pins (61) into the
Brackets axle holes and
split the ends. See
Figure C.
4. With assistance, set the Lower Drum (30) with attached Aluminum Bracket
(13) into the Crossbeam assembly. Fasten together using Hex Bolts (51),
Flat Washers (10), and Hex Nuts (9). See Figure D.
Fig. D
Fig. C
V4.0 3.5 cu. ft Electric Cement Mixer 8901043
Visit www.princessauto.com for more information 7
5. Use Hex Bolts (11)
to mount the Handle
Control Plate (8) to
the U-Tube (14).
Fasten together with
a Flat Washer (10)
and Hex Nut (9). See
Figure E.
6. Attach the Control Handle (1) to the U-Tube (14) shaft by inserting the
Spiral Spring (2) into the lower hole of the Spring Base. Press down on the
Spring Base until holes align on the U-Tube (14) end. See Figure E.
7. Insert the Hex Bolt (7) and secure with a Hex Nut (5). Tighten until the
Handle can still move. See Figure E.
8. Use gasket sealer (not
included) to attach the Rubber
Gasket (33) to the Upper
Drum (35), making sure the
holes in both align. The Gasket
must be flat against the Upper
Drum to ensure a proper seal.
Place the Upper Drum onto
the Lower Drum (30), making
sure the mounting holes align
in both. Insert the eight Hex
Bolt M6x16 (15) into each
mounting hole. Fasten Drums
together using an Elastic Washer (16). See Figure F.
Fig. E
Fig. F
8901043 3.5 cu. ft Electric Cement Mixer V4.0
8 For technical questions call 1-800-665-8685
9. Mount each Blade (32) inside the assembled Drum with the pointed end
facing down. The open end of each Blade should point in the direction of
the Drum rotation (counter-clockwise). Fasten Blade to Drums using the
Hex Bolt (34), Washer (10), and Hex Nut M8 (9).
10. Align the keyhole
slots, shifting the
Motor Box, block on
the pinion shaft.
Secure the unit to the
frame with four Hex
Bolt M8x60 (51) and
washers. See Figure
G.
11. Check all connections to verify that all screws, nuts, and bolts are securely
tightened.
BEFORE EACH USE
Inspect the general condition of the cement mixer. Check for loose hardware,
misalignment or binding of moving parts, cracked or broken parts, damaged
electrical wiring, damaged or cracked belts, and any other condition that may
affect its safe operation.
OPERATION
WARNING!
To prevent serious injury or property damage, read and understand owner’s
manual before operating.
Always use the proper protective equipment, including ANSI Z87.1 compliant
eye protection, heavy duty work gloves, and hearing protection.
Fig. G
V4.0 3.5 cu. ft Electric Cement Mixer 8901043
Visit www.princessauto.com for more information 9
Rotating Parts Hazard. Do not place tools, hoses, hands, arms, or any part
of the body inside the drum unless motor is off, and the power cord
unplugged.
Operate on a hard, level surface.
Do not leave the machine unattended while it is running.
Electrocution Hazard. Ensure that the mixer is properly grounded.
Do not plug or unplug the cord while standing in or around damp or wet
ground.
Do not operate the mixer in wet or damp areas or expose it to rain.
Turn power off and unplug before servicing.
Use only outdoor rated, grounded extension cords of the proper size.
Not for use by or around children.
1. Connect the Power Cord (48) to an electric outlet (or properly rated
grounded three prong extension cord).
2. Add material to the Drum. Typical maximum quantities include: 2 gallons
water with 3 shovels of cement and 15 shovels aggregate rock (using a
size 3 shovel, not included).
3. Adjust the Drum angle by pulling on the Control Handle (1). First,
disengage the locking pins on the Handle and push on it until the desired
angle is reached. Re-engage the locking pins.
4. Flip the switch (49) to the “ON(I) position.
TRANSPORTING
CAUTION! Before moving the unit,
ensure the drum is empty to reduce
the risk of injury.
When transporting the mixer, the
Locking Pin (64) must be secured to
hold the Lift Bar (23) in place.
AFTER EACH USE
1. Once materials are mixed, tilt Drum and dump materials where needed.
8901043 3.5 cu. ft Electric Cement Mixer V4.0
10 For technical questions call 1-800-665-8685
The materials are dumped while the Drum is rotating.
2. When finished, flip the Switch to the OFF(O) position and disconnect the
power cord.
3. Tilt the Drum angle as far down as possible to drain all fluids from the
Drum.
4. Immediately wash out all debris from the inside and outside of the Cement
Mixer. Scrub the inside of the Drum with a stiff, long handled bristle brush
for best results. Wipe external surfaces of the mixer with a clean cloth.
5. Store indoors where children are out of reach.
CARE & MAINTENANCE
WARNING! To prevent serious injury from accidental operation: Turn the
Power Switch of the tool to its OFFposition and unplug the tool from its
electrical outlet before performing any inspection, maintenance, or
cleaning procedures.
Maintain the cement mixer by adopting a program of conscientious repair and
maintenance in accordance with the following recommended procedures. It is
recommended that the general condition of any tool be examined before it is
used. Keep your tool in good repair. Keep handles dry, clean, and free from oil
and grease. The following chart is based on a normal operation schedule.
Maintenance Interval Maintenance Point
Periodically Recheck all fasteners and other connections for
tightness.
Belt Inspection and
Tensioning
Retighten belt after the first 25 hours of use. To test
the tension, follow the steps below.
Remove belt cover.
Examine belt for cracks, tears in the backing, or
other damage. Replace belt if damaged according
to steps below:
Loosen the elastic washer (53) bolts and slide the
bracket up as far as possible
Slide the old belt off the larger pulley first, then
remove it from the motor pulley.
V4.0 3.5 cu. ft Electric Cement Mixer 8901043
Visit www.princessauto.com for more information 11
Put the new belt around the small pulley first, then
around the large pulley.
Move the motor bracket down the belt until it is
properly tensioned according to the directions
below. Tighten the motor bracket bolts.
Check and adjust belt tension according to the
steps below:
Press on the center of the longest span on the V-
Belt (42) with moderate finger pressure. Then
measure the deflection distance, the distance that
the belt moved. The belt should deflect anywhere
from 1/2” to 3/4”.
If the belt deflects too much, tighten belt by
loosening the motor mounting bolts and moving
the motor away from the other pulley slightly.
Secure motor mounting bolts and retest tension. If
the belt is too long to be properly tensioned, it must
be replaced.
If the belt deflects too little, loosen the motor
bracket bolts and lift it upward. Secure motor
mounting bracket and retest tension.
Before use, replace belt motor cover.
TROUBLESHOOTING
Use the table below to troubleshoot problems before contacting service
personnel or your local dealer. If the problem continues after troubleshooting,
call your local dealer for assistance.
Failure Possible Cause Corrective Action
8901043 3.5 cu. ft Electric Cement Mixer V4.0
12 For technical questions call 1-800-665-8685
not start.
1. Cord is not connected. 1. Check that cord is plugged in.
2. No power at outlet. 2. Check power at outlet. If outlet is
unpowered turn off mixer and check
circuit breaker. If breaker is tripped,
make sure circuit has the correct
capacity for the tool and circuit has
no other loads.
3. Internal damage or wear. 3. Have technician service tool.
Mixer
operates
slowly.
Extension cord is too long or
wire size is too small.
Eliminate use of extension cord. If
an extension cord is needed, use
shorter/heavier gauge cord. See
Extension Cords in GROUNDING
section.
Excessive
noise or
rattling.
Belt (if equipped) is too loose
(slipping) or too tight (bearing
damage).
Properly tension belt.
Internal damage or wear. Have technician service tool.
Mixer is
overheati
ng or
overloadi
ng.
Running at 100% load for
extended time.
Allow for lighter, no-load intervals.
Blocked motor housing vents. Wear ANSI-approved safety goggles
and NIOSH approved dust
mask/respirator while blowing dust
out of motor using compressed air.
Motor is strained by long or
small diameter extension cord.
Eliminate use of extension cord. If
an extension cord is needed, use
one with the proper diameter for its
length and load. See Extension
Cords in GROUNDING section.
V4.0 3.5 cu. ft Electric Cement Mixer 8901043
Visit www.princessauto.com for more information 13
PARTS BREAKDOWN
8901043 3.5 cu. ft Electric Cement Mixer V4.0
14 For technical questions call 1-800-665-8685
PARTS LIST
# Description Qty
1
Control Handle
1
2
Spring
1
3
Washer
1
4
Hex Bolt M8x50
1
5
Hex Nut M10
2
6
Flat Washer 10
2
7
Hex Bolt M10x70
1
8
Handle Control Plate
1
9
Hex Nut M8
24
10
Flat Washer 8
16
11
Hex Bolt M8x25
14
12
Circlip 38
4
13
Aluminum Bracket
2
14
U-Tube
1
15
Hex Bolt
9
16
Elastic Washer 6
9
17
Washer 6
1
18
Flat Key A5x16
1
19
Gear
1
20
Bearing 60102Z
2
21
Cover
1
22
Next Bearing Plate
1
23
Lift Bar
1
24
Bearing 60206Z
2
25
Shaft
1
26
Up Bearing Plate
1
27
Aluminum Washer
10
28
Washer
10
29
Cast Iron Gear Ring
1
30
Lower Drum
1
31
Crosshead Bolt M6x12
8
32
Blade
2
33
Rubber Gasket
1
34
Hex Bolt M8x20
4
35
Upper Drum
1
36
Pinion Shaft
1
37
Hex Bolt M6x16
6
38
Motor Hood
1
39
Bearing 60905
2
40
Bearing Seat
1
41
Drum Pulley
1
42
V-Belt
1
43 Hex Bolt M8x30 2
44 Motor Bracket 1
45 Hex Bolt M8x40 3
46 Motor 1
47 Motor Cover 1
48 Cord with Plug 1
49 Switch 1
50 Clamp 1
51 Hex Bolt M8x60 4
52 Washer 14 1
53 Elastic Washer 14 1
54 Hex Bolt M14x30 1
55 Crossbeam 1
56 Hex Bolt M8x55 2
57 Hex Bolt M8x70 4
58 Wheel Bracket 1
59 Washer 24 4
60 Rubber Wheel 2
61 Cotter Pin 5x45 2
V4.0 3.5 cu. ft Electric Cement Mixer 8901043
Visit www.princessauto.com for more information 15
62 Support Bracket 1
63 Lift Bar seat 1
64 Locking Pin 1
65 Hex Bolt M8x40 1
V 4,0 8901043
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.
Conservez ce manuel afin de pouvoir le consulter plus tard.
Manuel d'utilisateur
Bétonnière électrique
de 3,5 pi cubes
8901043 Bétonnière électrique de 3,5 pi cubes V 4,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Tension 120 Vca, 60 Hz
Puissance du moteur 1/3 CV
Vitesse du moteur 1 400 tr/min
Capacité du tambour (pi cube) 3,5
Vitesse du tambour
36 tr/min
Roues en caoutchouc 10 po (2)
Rotation du tambour 360°
CONTENU DE LEMBALLAGE
Compartiment moteur
Tambour supérieur
Traverse
Poignée de commande
Plaque de poignée
Joint d’étanchéité en
caoutchouc
Support de roues
Tambour inférieur
Ferrure dappui
Roues (2)
Lames (2)
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant
d'utiliser cet outil. L'utilisateur doit respecter les précautions de base
lorsqu'il utilise cet outil afin de réduire le risque de blessure ou de
dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et d'entretien.
Bétonnière électrique
de 3,5 pi cubes
V 4,0 Bétonnière électrique de 3,5 pi cubes 8901043
Visitez www.princessauto.com pour plus d'informations 3
SÉCURITÉ PERSONNELLE
1. Restez alerte, gardez les yeux sur le travail et faites preuve de bon sens
lorsque vous utilisez loutil. Nutilisez pas loutil si vous êtes fatigué ou
sous l’effet de drogues, d’alcool ou de médicaments. Un instant
d’inattention lors de l’utilisation d’un outil peut provoquer des blessures
corporelles graves.
2. Portez des vêtements appropriés. Ne portez ni vêtements amples, ni
parures pendantes, ni bijoux. N’approchez ni les cheveux, ni les vêtements,
ni les gants des pièces mobiles. Les vêtements amples, les bijoux et les
cheveux longs risquent de se coincer dans des pièces mobiles. Les
bouches d’air sur l’outil recouvrent souvent les pièces mobiles, de sorte
qu’on devrait les éviter.
3. Portez l’équipement de protection individuelle adéquat, au besoin. Portez
des lunettes étanches conformes à la norme ANSI Z87.1 (pas des lunettes
de sécurité) avec des écrans latéraux ou un écran facial, au besoin. Portez
un masque antipoussières en présence de conditions de travail
poussiéreuses. Utilisez toujours des chaussures de sécurité à semelle
antidérapante, un casque de sécurité, des gants, des systèmes collecteurs
de poussière et une protection de l’ouïe, au besoin. Ceci s’applique à toutes
les personnes se trouvant dans laire de travail.
4. N’opérez pas loutil si vous devez étirer les bras pour le faire. Restez stable
et en équilibre à tout moment.
UTILISATION ET ENTRETIEN DE LA BÉTONNIÈRE
1. Ne forcez pas la bétonnière. Les produits sont plus sécuritaires et efficaces
lorsque vous les utilisez de la manière pour laquelle ils ont été conçus.
Planifiez votre travail et utilisez le bon produit pour la tâche à effectuer.
2. Vérifiez sil y a des pièces endommagées avant chaque utilisation. Vérifiez
attentivement pour déterminer si le produit est en bon état de
fonctionnement et permet d’exécuter la tâche prévue. Remplacez les pièces
endommagées ou usées immédiatement. Ne faites jamais fonctionner le
produit s’il comporte une pièce endommagée.
3. Rangez le produit lorsqu’il nest pas utilisé. Rangez-le dans un endroit sec
et sécuritaire, hors de la portée des enfants. Assurez-vous que l’outil est en
8901043 Bétonnière électrique de 3,5 pi cubes V 4,0
4 En cas de questions techniques, appelez le 1-800-665-8685
bon état de marche avant de le remiser et de le réutiliser.
4. N’utilisez que les accessoires recommandés par le fabricant pour une
utilisation avec votre produit. Les accessoires qui conviennent à un produit
peuvent causer un risque de blessure lorsqu’ils sont utilisés sur un autre
outil. N’utilisez jamais un accessoire qui possède une vitesse de
fonctionnement ou une pression d’utilisation plus basse que l’outil lui-
même.
5 Laissez les protecteurs en place et en bon état de marche. Ne faites jamais
fonctionner le produit sans que les protecteurs ne soient en place.
CONSIGNES DE SÉCURITÉ SPÉCIFIQUES
1. Veuillez lire et bien comprendre le manuel du propriétaire avant lutilisation
pour prévenir les blessures graves et tout dommage matériel.
2. Portez toujours le bon équipement de protection individuelle comprenant
une protection des yeux, des gants de travail robustes et une protection de
l’ouïe conformes à la norme ANSI Z87.1.
3. Risque attribuable aux pièces rotatives Ne placez pas doutils, de tuyaux,
les mains, les bras ou toute partie du corps dans le tambour à moins que
le moteur soit éteint et que le cordon d’alimentation soit débranché.
4. Utilisez uniquement sur une surface dure et de niveau.
5. Ne laissez pas lappareil sans surveillance pendant quil est en marche.
6. Risque d’électrocution Assurez-vous que la bétonnière est correctement
mise à la masse.
7. Ne connectez ou ne déconnectez pas le cordon pendant que l’appareil se
trouve sur un sol humide ou mouillé ou à proximité d’un tel sol.
8. Ne faites pas fonctionner la bétonnière dans un environnement mouillé ou
humide ou ne l’exposez pas à la pluie.
9. Coupez le courant ou déconnectez-la avant de procéder à son entretien.
10. Utilisez seulement des rallonges avec mise à la terre de la taille appropriée
certifiées pour un usage extérieur.
11. N’est pas conçu pour être utilisé par des enfants ou à proximité des
enfants.
V 4,0 Bétonnière électrique de 3,5 pi cubes 8901043
Visitez www.princessauto.com pour plus d'informations 5
GUIDE DIDENTIFICATION
A Compartiment
moteur
B Tambour supérieur
C Tambour inférieur
D Poignée de
commande
E Traverse
F Ferrure dappui
G Support de roues
ASSEMBLAGE ET INSTALLATION
1. Placez la traverse (no 55)
dans le support de roue (no
58) de manière à aligner les
trous de boulon. Fixez-les
ensemble au moyen des
boulons hexagonaux (no
57), des rondelles plates (no
10) et des écrous
hexagonaux (no 9). Placez le
support sur son côté afin de
faciliter lassemblage.
Consultez la figure A.
Fig. A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Power Fist 8901043 Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues