RAK RG15 8dBi Fiberglass Antenna Manuel utilisateur

Marque
RAK
Modèle
RG15 8dBi Fiberglass Antenna
Taper
Manuel utilisateur

Ce manuel convient également à

1 Warning
FCC Warning：
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions.
(1) This device may not cause harmful interference;
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
FCC Statement:
"This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help."
INTEGRATION INSTRUCTIONS
1. This Modular Approval is limited to OEM installation for mobile and fixed applications
only. The antenna installation and operating configurations of this transmitter, including
any applicable source-based time- averaging duty factor, antenna gain and cable loss
must satisfy MPE categorical Exclusion Requirements of 2.1091. This equipment
complies with FCC & Industry Canada exposure limits set forth for an uncontrolled
environment.
2. When the module is installed in the host device, the FCC ID label must be visible
through a window on the final device or it must be visible when an access panel, door or
cover is easily removed. If not, a second label must be placed on the outside of the final
device that contains the following text: ―Contains FCC ID: 2AF6B-RAK5147.
1
RAK2287X
1
3. The Shenzhen Rakwireless Technology Co., Ltd. modular transmitter is only FCC
authorized for the FCC Part15.247 listed on the grant, and that the host product
manufacturer is responsible for compliance to any other FCC rules that apply to the host
not covered by the modular transmitter grant of certification. If the grantee markets their
product as being Part 15 Subpart B compliant (when it also contains unintentional-
radiator digital circuity), then the grantee shall provide a notice stating that the final host
product still requires Part 15 Subpart B compliance testing with the modular transmitter
installed.
RF Exposure: This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
ISED Warning:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme
aux CNR d’Innovation, Sciences et Développement économique Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
This equipment complies with FCC & Industry Canada exposure limits set forth for an
uncontrolled environment.
L'équipement est conforme aux limites d'exposition établies par fac et Industrie Canada pour
les environnements non contrôlés.
The host product shall be properly labelled to identify the modules within the host
product. The ISED certification label of a module shall be clearly visible at all times
when installed in the host product; otherwise, the host product must be labelled to
display the ISED certification number for the module, preceded by the word "contains"
or similar wording expressing the same meaning, as follows:
Contains IC: 25908-RAK5147
2
RAK2287X
2
Le numéro d'homologation d'ISDE, le NIVM, le NMP et le NIVL ne doivent pas
nécessairement être adjacents.
Le numéro d'homologation se compose d'un numéro de compagnie (NC), attribué par le
Bureau d'homologation et de services techniques d’ISDE, suivi du numéro de produit
unique (NPU) attribué par le requérant. Le numéro d'homologation doit apparaître
comme suit : IC: 25908-RAK5147
RSS-102 Statement
This equipment complies with IC RSS_102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Cet équipement est conforme aux limites d'exposition aux radiations IC CNR_102
établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé
avec une distance minimale de 20 cm entre le radiateur et votre corps.
Labelling
The proposed FCC IC label format is to be placed on the module. If it is not visible when the
module is installed into the system,
“Contains FCC ID: 2AF6B-RAK5147, Contains IC: 25908-RAK5147” shall be placed on the
outside of final host system.
Labelling
— This radio transmitter [25908- RAK5147] has been approved by Innovation, Science and
Economic Development Canada to operate with the antenna types listed below, with the
maximum permissible gain indicated. Antenna types not included in this list that have a gain
greater than the maximum gain indicated for any type listed are strictly prohibited for use
with this device.
— Le présent émetteur radio [25908- RAK5147] a été approuvé par Innovation, Sciences et
Développement économique Canada pour fonctionner avec les types d'antenne énumérés
cidessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette
liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste,
sont trictement interdits pour l'exploitation de l'émetteur.
3
RAK2287X
3
Antenna info
Antenna #
Manufacturer
Model
Antenna
Gain
Antenna
Type
1#
Shenzhen
RAKwireless
Technology Co.,
Ltd
RAKARG15
8dBi
Fiber Glass
Antenna
2#
RAKARG14
5.8dBi
Fiber Glass
Antenna
3#
RAKARG19
5.1dBi
Fiber Glass
Antenna
4#
RAKARJ14
2.3 dBi
Dipole
Antenna
5#
RAKARJ16
2.3 dBi
Dipole
Antenna
About RAKwireless:
RAKwireless is a pioneer in providing innovative and diverse Cellular and LoRaWAN
connectivity solutions for both Edge and Gateway IoT devices. We believe that through easy to
use and modular designs we can accelerate the time to market for various IoT Applications in
order to optimize system deployment in both Developer and Commercial settings.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

RAK RG15 8dBi Fiberglass Antenna Manuel utilisateur

Marque
RAK
Modèle
RG15 8dBi Fiberglass Antenna
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents