Extron electronics TouchLink TLP Pro 725C Series Manuel utilisateur

Marque: Extron electronics

Modèle: TouchLink TLP Pro 725C Series

Taper: Manuel utilisateur

Ce manuel convient également à

TLP Pro 525C and 725C Series

User Guide

TouchLink

TouchLink Pro Touchpanel Control Systems

68-3319-01 Rev. D

01 20

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on the product, is intended to

alert the user of the presence of uninsulated dangerous voltage within the

product’s enclosure that may present a risk of electric shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing)

instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide, part number 68-290-01, on the Extron

website, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer darauf

aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes

gefährliche Spannungen herrschen, die nicht isoliert sind und die einen

elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige

Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,

EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in

den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer

68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del

producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de importantes instrucciones de uso y

mantenimiento recogidas en la documentación proporcionada con el

equipo.

Para obtener información sobre directrices de seguridad, cumplimiento

de normativas, compatibilidad electromagnética, accesibilidad y temas

relacionados, consulte la Guía de cumplimiento de normativas y seguridad

de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du

produit d’une tension électrique dangereuse susceptible de provoquer

un choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance

importantes qui se trouvent dans la documentation fournie avec le

matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la

réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets

connexes, lisez les informations de sécurité et de conformité Extron, réf.

68-290-01, sur le site Extron, www.extron.com.

Istruzioni di sicurezza • Italiano

AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di tensione non isolata pericolosa

all’interno del contenitore del prodotto che può costituire un rischio di

scosse elettriche.

ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad avvertire

l’utente della presenza di importanti istruzioni di funzionamento e

manutenzione nella documentazione fornita con l’apparecchio.

Per informazioni su parametri di sicurezza, conformità alle normative,

compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento

alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo

68-290-01, sul sito web di Extron, www.extron.com.

Instrukcje bezpieczeństwa • Polska

OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu

poinformować użytkownika o obecności izolowanego i niebezpiecznego

napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie

porażenia prądem elektrycznym.

UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do

ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji

(obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji

wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,

zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część

numer 68-290-01, na stronie internetowej Extron, www.extron.com.

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан

на продукте, предупреждает пользователя о наличии

неизолированного опасного напряжения внутри корпуса

продукта, которое может привести к поражению

электрическим током.

ВНИМАНИЕ: Данный символ, , если указан на продукте,

предупреждает пользователя о наличии важных инструкций

по эксплуатации и обслуживанию в руководстве,

прилагаемом к данному оборудованию.

Для получения информации о правилах техники безопасности,

соблюдении нормативных требований, электромагнитной

совместимости (ЭМП/ЭДС), возможности доступа и других

вопросах см. руководство по безопасности и соблюдению

нормативных требований Extron на сайте Extron: ,

www.extron.com, номер по каталогу - 68-290-01.

安全说明 • 简体中文

警告：产品上的这个标志意在警告用户该产品机壳内有暴露的危险电压，

有触电危险。

注意：产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍

使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见

Extron 安全规范指南，产品编号 68-290-01。

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks (

), registered service marks (

), and trademarks (

) are the property of RGBSystems, Inc. or

ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks

(

)

Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, FlexOS, Glitch Free, Global Configurator,

Global Scripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA,

PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,

System INTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTP Systems, and

ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS (Class D

Ripple Suppression), Codec Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), DriverConfigurator,

DSPConfigurator, DSVP (Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk,

MAAP, MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC (QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, SIS,

Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy

안전 지침 • 한국어

경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을

경고합니다.

주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에

대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및

규제 준수 안내서, 68-290-01 조항을 참조하십시오.

安全記事 • 繁體中文

警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有

重要的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資

訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規

遵守手冊》，準則編號 68-290-01。

安全上のご注意 • 日本語

警告: この記号が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意:この記号が製品上に表示されている場合は、本機の取扱説明書に

記載されている重要な操作と保守(整備)の指示についてユーザーの注意

を喚起するものです。

安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に

ついては、エクストロンのウェブサイト www.extron.com より『 Extron Safety

and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。

FCC Class B Notice

NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

This device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part15 of the FCC rules. These limits provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. There is no

guarantee that interference will not occur. If this equipment does cause interference to radio

or television reception, which can be determined by turning the equipment off and on, you

are encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

In order to maintain compliance with FCC regulations, shielded cables must be used with

this equipment. Operation with non-approved equipment or unshielded cables is likely to

result in interference to radio and TV reception. The user is cautioned that changes and

modifications made to the equipment without the approval of the manufacturer could void

the user’s authority to operate this equipment.

NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics see the Extron Safety and Regulatory

Compliance Guide on the Extron website.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Battery Notice

This product contains a battery. Do not open the unit to replace the battery. If the

battery needs replacing, return the entire unit to Extron (for the correct address, see the Extron

Warranty section on the last page of this guide).

CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used

Batteries According to the Instructions.

ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de pile.

Débarrassez-vous des piles utilisées selon le mode d’emploi.

Class 1 Laser Product

Any service to this product must be carried out by Extron Electronics and its qualified

service personnel.

CAUTION: Using controls, making adjustments, or performing procedures in a manner

other than what is specified herein may result in hazardous radiation exposure.

NOTE: For more information on safety guidelines, regulatory compliances,

EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and

Regulatory Compliance Guide” on the Extron website.

Produit laser de classe1

Si ce produit a besoin d’un quelconque entretient, celui-ci doit être fait par

ExtronElectronics et son personnel qualifié.

ATTENTION : L’utilisation de commandes, la réalisation de réglages, ou l’exécution de

procédures de manière contraire aux dispositions établies dans le présent document,

présente un risque d’exposition dangereuse aux radiations.

Remarque : Pour plus d'informations sur les directives de sécurité, les conformités

de régulation, la compatibilité EMI/EMF, l'accessibilité, et les sujets en lien, consultez le

«Informations de sécurité et de conformité Extron» sur le site internet d'Extron.

FCC Radio Frequency Interference — Safety Notices

Antenna Warnings

WARNING: The radiated output power of the wireless device is far below the FCC

radio frequency exposure limits. Nevertheless, the unit should be used in such a manner that

the potential for human contact during normal operation is minimized. To avoid the possibility of

exceeding the FCC radio frequency exposure limits, you should keep a distance of at least 20

cm between you (or any other person in the vicinity) and the antenna that is built into the unit.

AVERTISSEMENT: La puissance de sortie rayonnée de l’appareil sans fil est bien

inférieure aux limites d’exposition aux radiofréquences de l’organisme américain FCC

(FederalCommunicationsCommission). Néanmoins, l’unité doit être utilisée de telle sorte que le

contact humain éventuel durant le fonctionnement régulier de l’appareil soit réduit. Afin d’éviter

toute possibilité de dépassement des limites d’exposition aux radiofréquences de la FCC, vous

êtes tenu de conserver une distance de 20cm (8’) au minimum entre vous (ou toute autre

personne située à proximité) et l’antenne intégrée à l’unité.

NOTE: The wireless network device must be installed and used in strict accordance with Extron

Electronic’s instructions as described in the user documentation that comes with the product.

Any other installation or use will violate FCC Part 15 regulations.

Compliance IC

Canada, Industry Canada (IC) Notices

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject

to the following two conditions: (1) this device may not cause interference, and (2) this device

must accept any interference, including interference that may cause undesired operation of the

device.

This device complies with RSS247 of Industry Canada.

This Class B digital apparatus complies with Canadian ICES-003, Issue 4, and RSS-247, No 4.

To prevent radio interference to the licensed service, this device is intended to be operated

indoors and away from windows to provide maximum shielding. Equipment (or its transmit

antenna) that is installed outdoors is subject to licensing.

IC Antenna Statement

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a

type and maximum (or lesser) gain approved for the transmitter by Industry Canada.

To reduce potential radio interference to other users, the antenna type and its gain should be so

chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary

for successful communication.

This radio transmitter has been approved by Industry Canada to operate with the antenna types

listed below with the maximum permissible gain and required antenna impedance for each

antenna type indicated. Antenna types not included in this list, having a gain greater than the

maximum gain indicated for that type, are strictly prohibited for use with this device.

Type: Chip

Maximum Peak Gain: 0.5 dBi

Impedance: 50 Ohm

Radio Frequency (RF) Exposure Information

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20 cm

between the antenna and your body.

IC conformité

Canada, avis d’Industry Canada (IC)

CAN ICES-3 (B)/NMB-3(B)

Cet appareil est conforme aux normes des cahiers des charges sur les normes radioélectriques

(CNR) de l’ISDE applicables aux appareils exempts de licence. Son utilisation est subordonnée

aux deux conditions suivantes : (1) Cet appareil ne doit provoquer aucune interférence, et (2) cet

appareil doit accepter toute interférence, y compris l’interférence susceptible de compromettre

son fonctionnement.

Cet appareil est conforme aux normes CNR-247 de l’ISDE.

Cet appareil numérique de classe B est conforme aux normes canadiennes NMB-003, 4ème

édition, et CNR-247, 4ème édition.

Afin d’éviter toute interférence électromagnétique avec le service faisant l’objet d’une licence,

cet appareil doit être utilisé dans des applications intérieures et être éloigné des fenêtres afin de

garantir une protection maximale. L’équipement (ou son antenne d’émission) installé dans des

applications extérieures fait l’objet d’une licence.

Note du ministère ISDE Canada relative aux antennes

En vertu de la réglementation d’Industrie Canada, cet émetteur radio doit être utilisé uniquement

avec une antenne d’un certain type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur

par le ministère. Afin de réduire les éventuelles interférences électromagnétiques préjudiciables

aux autres utilisateurs, il est essentiel de choisir le type d’antenne et son gain de telle sorte que

la puissance isotrope rayonnée équivalente (EIRP) se révèle inférieure aux besoins requis pour

garantir une communication satisfaisante.

Le fonctionnement de l’émetteur radio avec les types d’antenne listés ci-dessous a été approuvé

par Industrie Canada. Le gain maximal autorisé et l’impédance requise pour chaque antenne

sont par ailleurs indiqués. L’utilisation des types d’antenne non inclus dans cette liste, qui

possèdent un gain supérieur au gain maximal indiqué pour chaque type, est strictement interdite

avec cet appareil.

Type : puce électronique

Gain d’antenne maximal : 0.5 dBi

Impédance : 50 ohms

Informations sur les limites d’exposition aux radiofréquences

Cet équipement est conforme aux limites d’exposition aux radiations CNR-102 établies pour un

environnement non contrôlé. Il doit être installé et contrôlé à une distance minimale de 20 cm

entre l’antenne et votre corps.

Conventions Used in this Guide

Notiﬁcations

In this user guide, the following are used:

WARNING: Potential risk of severe injury or death.

AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

X1&

X2)

X2#

X2!

}

NOTE: For commands and examples of computer or device responses

mentioned in this guide, the character “0” is used for the number zero and “O”

represents the capital letter “o”.

Computer responses and directory paths that do not have variables are written in the font shown

here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are written

in the font shown here:

From the File menu, select New.

Click the OK button.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at www.extron.com/technology/glossary.aspx.

Contents

Introduction............................................................ 1

About the TLP Pro 525C and 725C Series ..............1

Features .................................................................. 2

Application Diagram ................................................3

Requirements ..........................................................4

Software .............................................................4

Hardware ............................................................4

Panel Features ...................................................... 5

Front Panel and Enclosure Features ........................5

Base Features .........................................................6

Installation Overview ........................................... 9

Mounting ............................................................... 11

Planning ................................................................ 11

Tools Required for Installation ................................ 12

Included Parts ....................................................... 12

TLP Pro 525C ...................................................12

TLP Pro 725C ...................................................12

Ensuring Adequate Under-table Clearance

for Retractors ....................................................... 13

Retractor Clearance for the

TLP Pro 525C Series .......................................13

Retractor Clearance for the

TLP Pro 725C Series .......................................14

Cutting the Table ...................................................15

Cut-out Dimensions ..........................................15

Cutting the Surface ...........................................15

Running Cables .....................................................16

Preparing MAAP or AAP Modules .........................17

Assembling the 525C MAAP Module ................17

Assembling the AAP Module ............................. 17

Preparing Cable Pass-through Modules ................18

Assembling the 525C Pass-through

Cable Module ..................................................18

Assembling the Series/2

Cable Pass-through Module.............................18

Installing Modules..................................................19

TLP Pro 525C ...................................................19

TLP Pro 725C ...................................................22

Special Considerations for Power Modules .......23

Mounting the Touchpanel Enclosure ...................... 24

Installing Cable Retractors (Optional) .....................25

On-screen Menus ............................................... 26

Setup Menu ..........................................................26

Status ...............................................................26

Network ............................................................ 27

Display .............................................................. 29

Audio ................................................................30

Advanced .........................................................31

Conﬁguration Software ..................................... 32

Conﬁguration Software .......................................... 32

Installing GUI Designer, Global Conﬁgurator,

Toolbelt, and Global Scripter ............................33

Using the Software ............................................34

Touchpanel Web Page ..........................................35

Updating the Firmware ..........................................36

Downloading Firmware ......................................36

Updating Firmware Using Toolbelt ..................... 36

Reference Material ............................................. 37

Network Port Requirements and Licensed

Third-Party Software ............................................37

Reset Modes.........................................................37

Use Factory Firmware .......................................37

Reset All IP Settings .......................................... 38

Reset to Factory Defaults ..................................38

Enable or Disable the DHCP Client ....................39

Secure Sockets Layer (SSL) Certiﬁcates ................ 39

IEEE 802.1X Certiﬁcates ........................................40

Certiﬁcate File Requirements .............................40

Private Key File Requirements ...........................40

TLP Pro 525C and 725C Series Touchpanels • Contents ix

TLP Pro 525C and 725C Series Touchpanels • Contents x

Introduction

This guide describes the function, installation, and operation of the Extron Touchlink Pro

Touchpanels:

• TLP Pro 525C

• TLP Pro 525C NC

• TLP Pro 725C

• TLP Pro 725C NC

Unless otherwise stated:

• The terms “TLP Pro 525C” or “TLP Pro 525C Series” refer to both the 525C and 525C NC

models.

• The terms “TLP Pro 725C” or “TLP Pro 725C Series” refer to both the 725C and 725C NC

models.

• The term “touchpanel” refers to all four models.

• The terms “Cable Cubby” and “enclosure” refer to the enclosure that is mounted in the table

top.

This section discusses the following topics:

• About the TLP Pro 525C and 725C Series

• Features

• Application Diagram

• Requirements

About the TLP Pro 525C and 725C Series

The TLP Pro 525C is a Series/2 Cable Cubby touchpanel with a flip-up, 5-inch 800x480 (WVGA),

LCD touchscreen.

The TLP Pro 725C is a Series/2 Cable Cubby touchpanel with a flip-up, 7-inch 1024x600

(WSVGA), LCD touchscreen.

The TLP Pro 525 NC and TLP Pro 725C NC are streamlined versions of these touchpanels, with

a set of features designed to adhere to government and military security protocols.

They combine the AV system control of conventional touchpanels with the cable management

convenience of the CableCubby. They feature a tilt-up, full-color touchscreen in an elegant,

metal enclosure that can be mounted securely into a tabletop, lectern, or other flat surface.

The user can define the graphics and the functions associated with those graphics, providing

versatility and adaptability to the configuration and control of an AV system. The screen layout

is designed with the Extron GUI Designer software. The functions can be assigned to the

screen objects with the Extron Global Configurator Plus and Global Configurator Professional

configuration software or with Global Scripter programming software.

A motion sensor, light sensor, and a speaker provide sleep mode, auto dimming, and audible

feedback respectively.

TLP Pro 525C and 725C Series Touchpanels • Introduction 1

Features

• LCD touchscreen

• TLP Pro 525C — 5" capacitive ﬂip-up touchscreen with 800x480 (WVGA) resolution

• TLP Pro 725C — 7" capacitive ﬂip-up touchscreen with 1024x600 (WSVGA) resolution

• 24-bit color depth. Vibrant edge-to-edge glass display with a more responsive control

surface.

• Gorilla Glass

screen is tough, scratch, and smudge-resistant — Corning

Gorilla

Glass is stronger and more scratch-resistant than standard glass, while maintaining touch

sensitivity, color saturation, and brightness.

• Faster, quad-core processing — provides enhanced response and overall user

experience.

• Power over Ethernet (PoE 802.3af, class3) compliance — provides power and

communication over a single Ethernet cable (power injector sold separately).

• Compatible with the full range of Extron IPL Pro and IPCP Pro control processors

— allows easy integration into existing systems.

• Built-in speaker — provides audible feedback from button presses.

• Patented modular design for fast assembly and serviceability — AV connectivity can

be installed or serviced from the top of the enclosure after the enclosure is installed.

• Series/2 Cable Access Enclosure design offers easy access to AV, data, and power

connections:

The TLP Pro 525C enclosure accommodates:

• Series/2 AC or AC+USB power module and either ﬁve AV cables, or two single space

MAAPs, or two Retractors.

• AC Power and AC+USB Power Modules are available for US, Europe, and other major

world markets.

• Optional Retractor cable retraction system supports most AV, data, and power.

• Included TLP Pro 525C Bracket Kit provides additional flexibility when configuring the

Cable Cubby.

The TLP Pro 725C enclosure accommodates up to three Series/2 modules in a variety of

configurations. There are three different types of modules:

• Accommodates Series/2 AC or AC+USB power module, plus three Retractors, eight AV

cables, and/or three AAP – Architectural Adapter Plates per bracket.

• AC Power and AC+USB Power Modules are available for US, Europe, and other major

world markets.

• Optional Retractor cable retraction system supports most AV, data, and power.

• Included Cable Cubby Series/2 Connectivity Bracket Kits provide additional flexibility

when configuring Cable Cubby Series/2 cable access enclosures.

• Compatible with TeamWork Show Me Cables — Show Me cables provide convenient

connectivity and user input selection and control for TeamWork Collaboration Systems. Visit

the TeamWork System Builder at www.extron.com to create a customized system for your

collaboration environment.

• Integrated side clamps secure enclosure to the furniture surface — the Cable Cubby

can be secured in place without additional parts or tools.

• System connection status indicator — the communication LED provides visual feedback

if the touchpanel is not communicating with a control processor.

• Automatic clock synchronization — allows the touchpanel to display the accurate time

and date.

• Energy-saving features —

• Light sensor adjusts screen brightness as the ambient room lighting changes.

• Adjustable sleep timer puts the touchpanel into sleep mode.

TLP Pro 525C and 725C Series Touchpanels • Introduction 2

• Motion detector wakes the touchpanel.

• Integrated lid switch automatically wakes the touchpanel when opened and can trigger

any other system function.

• Manage, monitor, and control this device remotely — using GlobalViewer Enterprise

(GVE) Resource Management software.

• Fully customizable using Extron control system software — GUI Designer combined

with Global Conﬁgurator Plus, Global Conﬁgurator Professional, or Global Scripter.

• Supports the Extron Control App and Extron Control for Web.

• High speed USB 2.0 port — for future expansion. This feature is not available on the NC

models.

• JITC Certified — Successfully completed interoperability and information assurance testing

for use in government applications and other mission-critical environments.

Application Diagram

Figure 1 shows one application for the TLP Pro 725C. The TLP Pro 525C can be used in similar

systems.

POWER

12V

--A MAX

Tx Rx RTSCTS

COM 1

Tx Rx

COM 2

VCG

VOL

RELAYS

1 2 C

1 2 3 4 G

DIGITAL I/O

PWR OUT = 6W

eBUS

+V +S

-S

LAN

IPCP PRO 250

IR/S

S G

HCT 103

INPUTS

234

SIGNAL

HDCP

3 4

HCR 102

CONFIG

SIGNAL

HDCP

LPCM-2CH

MULTI-CH

INPUT AUDIO

ENTER

HOLD FOR 720p/1080p

MODEL 80

FLAT PANEL

Audio

VGA

HDMI

HDMI/CEC

HDMI

CATx Cable

up to 230'

(70 m)

Ethernet/PoE

Ethernet

Laptops

Display

Ext

ron

404

ransmitter

Extron

HC 404

Receiver

Extron

TLP Pro 725C

7" Cable Cubby TouchLink

Pro Touchpanel

Extron

IPCP Pro 250

IP Link Pro

Control Pr

ocessor

Ethernet

Figure 1. Application Diagram

TLP Pro 525C and 725C Series Touchpanels • Introduction 3

Requirements

Software

For a complete list of the requirements for running GUI Designer, Global Configurator Plus and

Professional, Global Scripter, and Toolbelt see the Extron web page (www.extron.com) for that

software.

NOTE: These touchpanels are not compatible with GlobalConfigurator 3 or

GUIConfigurator.

Hardware

An Extron IP Link Pro control interface must also be connected to the same network domain as

the TLP Pro TouchLink panel. See www.extron.com for a list of suitable controller processor.

NOTE: These touchpanels are not compatible with Extron IP Link (non-Pro) control

processors.

TLP Pro 525C and 725C Series Touchpanels • Introduction 4

Panel Features

This section describes the TLP Pro touchpanels:

• Front Panel and Enclosure Features

• Base Features

Front Panel and Enclosure Features

Figure 2 shows the TLP Pro 725C front panel and the Cable Cubby enclosure. The

TLP Pro 525C is very similar.

Figure 2. TLP Pro 725C Front Panel

Capacitive LCD touchscreen — made of tough, scratch-resistant, Gorilla glass.

• The TLP Pro 725C series has a 7-inch screen with a 1024x600 resolution.

• The TLP Pro 525C has a 5-inch screen with a 800x480 resolution

Motion sensor (2) — Detects motion between three to ﬁve feet from the touchpanel, and at

least 15° from the center axis.

• When no motion is detected for a user-deﬁned period of time, the touchpanel enters

sleep mode.

NOTE: For sleep mode to be activated, the sleep timer must have been set up (see

Display on page 29).

• When motion is detected by the sensor while the display is in sleep mode, the screen

display is restored and active.

NOTES:

• For the screen to be restored through the motion detector, wake on

motion must have been set up (see Display on page 29).

• If wake on motion is not activated, the screen is restored by touching it.

figure 2

LCD screen

Motion sensor

LCD screen

Motion sensor

Communication LED (see

next page)

Light sensor (see next page)

Activation Switch (see next

page)

Speaker (see the next page)

TLP Pro 525C and 725C Series Touchpanels • Panel Features 5

Communication LED (see ﬁgure 2 on the previous page) — Shows the conﬁguration and

connection status of the touchpanel:

• Unlit during normal operation (the touchpanel is conﬁgured and connected to an IP Link

Pro control processor).

• Blinks red if the touchpanel has been conﬁgured but is not connected to an IP Link Pro

control processor.

• Lit solidly if the touchpanel is not conﬁgured.

The indicator can be toggled between enabled and disabled, using the Setup Menu

Advanced screen (see page 31).

Light sensor — This sensor monitors ambient light level and adjusts screen brightness,

based on the settings conﬁgured using the Setup Menu Display screen (see page 29).

Activation Switch – the left side of the lid hinge mechanism contains a switch. When the lid

is closed, the switch sends the screen into sleep mode. When the lid is opened, the screen

display is restored and active.

When the lid is shut, the screen is not activated by motion near the touchpanel.

Speaker — A single speaker, located on the side of the enclosure, provides audible

feedback for the user.

Base Features

Figure 3 shows the TLP Pro 725C base panel. The TLP Pro 525C is very similar.

LAN / PoE

275 mA

USB

RESET

Figure 3. TLP Pro 725C Base Panel

Menu button — Pressing the Menu button activates the setup menu (see Setup Menu on

page 26).

Reset button — Pressing the Reset button allows the unit to be reset in any of three

different modes and can also be used to toggle between enabling and disabling the DHCP

client (see Reset Modes on page 37).

Reset LED — Provides feedback about the reset status when the user presses the Reset

button (see Reset Modes).

USB port — Compatible with USB 2.0.

LAN/PoE port — The TLP Pro 725C must be powered by a PoE power injector through

this port. Connect the touchpanel to a PoE power injector using a twisted pair cable,

terminated with an RJ-45 connector. Connect the power injector to the LAN through a

nework switch.

The network port has two LEDs. The green LED lights steadily to indicate that the

touchpanel is connected correctly to a network. The yellow LED blinks to indicate that data

is being passed to or from the touchpanel.

NOTE: The power injector must be purchased separately.

Communication LED

Light sensor

Activation Switch

Speaker

figure 3

Menu button

Reset button

Reset LED

USB port

LAN/PoE port

TLP Pro 525C and 725C Series Touchpanels • Panel Features 6

ATTENTION:

• The installation must always be in accordance with the applicable provisions of National

Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1,

section 16.

• Cette installation doit toujours être conforme aux dispositions applicables du Code

américain de l’électricité (National Electrical Code) ANSI/NFPA 70, article 725, et du

Code canadien de l’électricité, partie1, section16.

• The power supply shall not be permanently ﬁxed to building structure or similar structure.

• La source d’alimentation ne devra pas être ﬁxée de façon permanente à une structure de

bâtiment ou à d’autres structures similaires.

• Power over Ethernet (PoE) is intended for indoor use only. It is to be connected only to

networks or circuits that are not routed to the outside plant or building.

• L’alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur uniquement.

Elle doit être connectée seulement à des réseaux ou des circuits qui ne sont pas routés

au réseau ou au bâtiment extérieur.

• The touchpanels are intended for connection to a Power over Ethernet circuit for

intra-building use only and are considered to be part of a Network Environment 0 per

IEC TR62101.

• Les écrans tactiles sont conçus pour une connexion à un circuit PoE pour une utilisation

intérieure uniquement et sont considérés comme faisant partie d’un environnement

réseau 0 selon la norme IEC TR62101.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling

spaces or in wall cavities. The power supply is to be located within the same vicinity as

the Extron AV processing equipment in an ordinary location, Pollution Degree 2, secured

to the equipment rack within the dedicated closet, podium, or desk.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une

utilisation dans les espaces d’aération ou dans les cavités murales. La source

d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel

dans un endroit ordinaire, avec un degré2 de pollution, ﬁxé à un équipement de rack à

l’intérieur d’un placard, d’une estrade, ou d’un bureau.

• Always use a power supply provided by or speciﬁed by Extron. Use of an unauthorized

power supply voids all regulatory compliance certiﬁcation and may cause damage to the

supply and the end product.

• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.

L’utilisation d’une source d’alimentation non autorisée annule toute conformité

réglementaire et peut endommager la source d’alimentation ainsi que le produit ﬁnal.

• If these products are not provided with a power supply, they are intended to be supplied

by a UL Listed power source marked “Class 2” or “LPS” and output rated 48 VDC or

56 VDC (PoE), minimum 0.35 A, or UL Listed Extron XTP/DTP remote power source.

• Si ces produits ne sont pas fournis avec une source d’alimentation, ils doivent être

utilisés avec une source d’alimentation certiﬁée UL de classe 2 ou LPS avec une tension

nominale 48 Vcc ou 56 Vcc (PoE), 0,35 A minimum, ou une source d’alimentation à

distance XTP/DTP Extron certiﬁée UL.

• Extron power supplies are certiﬁed to UL/CSA 60950-1 and are classiﬁed as LPS

(Limited Power Source). Use of a non-LPS or unlisted power supply will void all

regulatory compliance certiﬁcation.

• Les sources d’alimentation Extron sont qualiﬁées UL/CSA60950-1 et sont

classéesLPS(LimitedPowerSource). L’utilisation d’une source d’alimentation non-listée

ou non-listéeLPS annulera toute certiﬁcation de conformité réglementaire.

mise en garde

Attention

TLP Pro 525C and 725C Series Touchpanels • Panel Features 7

1. Connect a straight-through Ethernet cable from the power injector to a switch or router

(ﬁgure 14,

). This cable carries network information from the switch or router to the power

supply input.

2. Connect a second straight-through cable (

) from the power injector to the touchpanel.

This cable carries the network information and 48VDC from the power injector to the

touchpanel.

3. Connect the IEC power cord to a convenient 100 VAC to 240 VAC, 50-60 Hz power source

(

Figure 20 shows the Extron XTP PI 100. Your power injector may look different.

100-240V

50-60Hz

0.4A MAX

XTP

PWR

XTP PWR

To network switchTo touchpanel

Figure 4. XTP PI 100 Power Injector

An Extron IPL Pro control processor must also be connected to the same network domain

as the TouchLink Pro touchpanel (see the www.extron.com for a list of compatible models).

figure 4

TLP Pro 525C and 725C Series Touchpanels • Panel Features 8

Installation

Overview

This section provides an overview of the installation process. Follow the links for a more detailed

explanation of each step.

1. Before starting to install the touchpanel, download and install the latest versions of the

following software:

 GUI Designer — For designing layouts for Extron TouchLink Pro touchpanels and third

party touch interfaces.

 Global Configurator Plus and Professional — For setting up and conﬁguring the

control processor and touchpanel.

 Toolbelt — Provides device discovery, device information, ﬁrmware updates,

and conﬁguration of network settings, system utilities, and user management for

TouchLinkPro devices.

 Global Scripter — Provides an integrated development environment for Extron control

systems programming.

See Configuration Software on page 32.

2. Before starting to install the touchpanel, obtain the following network information from your

network administrator:

 Dynamic Host Configuration Protocol (DHCP) status (on or off). If DHCP is off, you

also require:

 IP address

 Subnet mask

 Gateway

 User name — This can be either admin or user.

 Password — The factory conﬁgured passwords for all accounts on this device have

been set to the device serial number. Passwords are case sensitive.

NOTE: If the device is reset to default settings, the password will be the default

password conﬁguration. The default password is extron (for either admin or

user.

 MAC address — Make a note of the touchpanel MAC address, which can be found on

the label on the base.

3. Decide where to mount the touchpanel. If you are installing retractors, ensure there is

adequate clearance under the table (see Ensuring Adequate Under-table Clearance for

Retractors on page 13).

4. Cut a hole in the table for mounting the touchpanel (see Cutting the Table on page 15).

ATTENTION:

• The opening in the table for the Cable Cubby should be cut only by licensed and

bonded craftspeople. Exercise care to prevent scarring or damaging the furniture.

• L’ouverture dans la table pour le Cable Cubby doit être coupée uniquement par un

ouvrier détenteur d’une licence. Veillez à ne pas laisser de marques ni à détériorer le

mobilier.

TLP Pro 525C and 725C Series Touchpanels • Installation Overview 9

5. Run all cables to the touchpanel. These include Ethernet cable and cables for Retractors,

power modules, AAPs, and MAAPs (see Running Cables on page 16).

Leave enough slack to connect the cables before the enclosure is installed in the table.

6. Set up the touchpanels for network communication:

NOTE: If you use the setup menu to conﬁgure the touchpanel, conﬁgure the touchpanel

before mounting (see step 8, below) as you will need access to the Menu button, which

is under the table on the unit base.

 Connect an Ethernet cable to the touchpanels (see Base Features on page 6).

 Connect the PC that you are using for setup, the Extron control processor, and the

touchpanel to the same Ethernet subnetwork.

 Use the Setup Menu (see page 26) or Toolbelt to set the DHCP status and, if

required, the IP address, subnet mask, gateway, and related settings for the touchpanel.

ATTENTION:

• Do not power on the touchpanels or control processors until you have read the

Attention about Power over Ethernet (PoE) power supplies (see page 7).

• Ne branchez pas les écrans tactiles ou les processeurs de contrôle avant d’avoir lu

la mise en garde sur les sources d’alimentation via Ethernet (PoE) (voir page 7).

 Once the touchpanel is set up for network communication, disconnect the Ethernet

cable before installing modules and mounting the enclosure.

7. Prepare and install modules in the touchpanel enclosure (see Preparing MAAP or AAP

Modules on page 17, Preparing Cable Pass-through Modules on page 18, and

Installing Modules on page 19).

If you are installing Retractors, install an empty bracket into the touchpanel and install the

Retractors after the enclosure is mounted.

8. Mount and cable the enclosure (see Mounting, starting on the next page).

9. Conﬁgure the TLP Pro touchpanels — the GUI Designer Help File, the Global Conﬁgurator

Help File, and the Toolbelt Help File provide step-by-step instructions and detailed

information.

The Global Configurator Help File also includes an introduction to that software and sections

on how to start a project and configuration.

Global Scripter provides an Extron-exclusive Python library (ControlScript) and

Global Scripter modules to get you started. See the GlobalScripter Help File for more

information.

TLP Pro 525C and 725C Series Touchpanels • Installation Overview 10

La page charge ...

Extron electronics TouchLink TLP Pro 725C Series Manuel utilisateur

Marque: Extron electronics

Modèle: TouchLink TLP Pro 725C Series

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Extron electronics TouchLink TLP Pro 725C Series User manual

Extron electronics TouchLink TLP Pro 725C Series Manuel utilisateur

Ce manuel convient également à

Extron electronics TouchLink TLP Pro 725C Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents