Singing Machine SML668G Manuel utilisateur

TM

SML668G/SML668W

INSTRUCTION MANUAL/ MANUAL DE INSTRUCCIONES/

MODE D’EMPLOI

www.singingmachine.com

The Singing Machine® is a registered trademark of The Singing Machine Co., Inc.

The Singing Machine® es marca registrada de The Singing Machine Co., Inc.

The Singing Machine® est une marque déposée de The Singing Machine Co., Inc.

— E1 —

Warnings

Important Safety Information

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all Instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in

accordance with the Manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. When the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete

outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with a cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms

or when unused for long periods of time.

14. Refer all servicing to qualified service

personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

15. WARNING: To reduce the risk of fire or electric shock, do not

expose this apparatus to rain or moisture. Do not place objects

filled with water, such as a vase, on the apparatus.

16. The AC mains plug is used as the power disconnect device and

it should remain readily accessible and operable during intended

use. In order to completely disconnect the apparatus from

power, the mains plug should be completely removed from the

AC outlet socket.

17. CAUTION: To reduce the risk of fire or explosion, do not expose

batteries to excessive heat such as sunshine, fire or other

heat sources.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The Caution marking is located on the bottom panel.

DANGEROUS VOLTAGE: The lightning flash with arrowhead

symbol within an equilateral triangle is intended to alert the

user to the presence of uninsulated dangerous voltage within

the product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THIS UNIT TO RAIN OR MOISTURE.

ATTENTION: The exclamation point within an equilateral

triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions

in the literature accompanying this product.

FCC WARNING: This equipment may generate or use radio frequency

energy. Changes or modifications to this equipment may cause harmful

interference unless the modifications are expressly approved in the

instruction manual. The user could lose the authority to operate this

equipment if an unauthorized change or modification is made.

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The rating information is located at the rear of the unit.

RF Exposure Warning Statements:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment.

DRIPPING WARNING: This product shall not be exposed to dripping or

splashing, and no objects filled with liquids, such as vases, shall be placed

on the product.

VENTILATION WARNING: The normal ventilation of the product shall not

be impeded for intended use.

Warning: Changes or modifications to this unit not expressly approved

by the party responsible for compliance could void the user’s authority to

operate the equipment.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF

PLUG TO WIDE SLOT AND FULLY INSERT.

— E2 —

Included

Please make sure the following items are included.

Manual

Main Unit

Wireless

Microphone

USB Charging Cable

— E3 —

Location of Controls (Front)

1. USB Port

2. (Bluetooth)/VOCALS OFF Button

3. REPEAT Button

4. (Skip) Button

5. Music Volume/Mic Volume control

6. FUNCTION Button

7. / (ON/STANDBY/LIGHTS) Button

8. Display

9. / (PLAY/PAUSE/STOP) Button

10. (Voice effects down) Button

11. (Voice effects up) button

12. (Skip) Button

13. RECORD Button

u

w

v

Uak

am

V at

X

W

x al

y

— E4 —

Location of Controls (Rear)

1. Handle

2. Extendable MIC holders

3. MIC 1 Jack

4. MIC 2 Jack

5. AUX IN Jack/*Reset hole

6. Type-C USB Jack

7.

+

(Mic Volume +) button

8

-

(Mic Volume -) button

9 Wireless mic power indicator

10 Wireles mic power button

WIRELESS

MICROPHONE

VW

Xat

u

v

w

x y

U

v

* If this device doesn't work, you can reset the device using the pin.

— E5 —

Rechargeable Battery

This unit has a built-in rechargeable battery pack for cordless operation. The battery should

not be serviced or replaced by the user. To maximize battery life, it is recommended to charge

the unit once a month. When the battery indicator on the display flashes slowly, follow these

steps to recharge:

1 Connect the included USB cable

to the USB Type-C port at the

rear of the unit. Plug the other

end into a computer USB port

or USB charging device (not

included).

2 Charge the unit for about 4

hours to achieve a full charge.

The battery indicator will turn off

when fully charged.

3 Once fully charged, disconnect

the USB cable. The unit can be

used for approximately 4 hours,

depending on the selected

function.

USB socket

NOTE: This unit is operated by an internal chargable lithium battery. The unit cannot

be turned on if the battery level is too low. It's suggested for the user to the unit for

about 5 mins to charge up the battery. (This will not fully charge the battery, see

above for charging time required).

ATTENTION: The sound volume will adjust automatically when the battery is not full.

Recycling and Disposal Information:

• Do not dispose of electronic devices or any of their components.

(especially batteries and LCD displays) in your municipal trash collection.

• Consult your local waste management authority or a recycling organization like Earth911.

com to find an electronics recycling facility in your area.

CAUTION: Rechargeable batteries must be recycled or disposed of properly.

— E6 —

Connections

Charging Instructions:

1 Connect the included USB cable to the

USB Type-C port on the back of the

device.

2 Plug the other end of the cable into a

DC5V 1A socket.

USB socket

Connecting to AUX IN Jack:

1 Use an appropriate cable (3.5mm

audio cable not included) to connect

an external device.

2 Refer to page E14 for instructions

on selecting and using the Aux In

function.

AUX IN

To External Unit

AUDIO OUTPUT

/ HEADPHONE JACK

Directions to change the light modes on your device:

There are 3 built-in light modes. Repeatedly

press / button to switch between lighting

effects.

u

— E7 —

Connections

Connecting Wireless Microphone(s):

Changing the Wireless Microphone’s Battery:

1 Press the / button to turn on the

unit.

2 Press the button on the Wireless

Mic to turn on the microphone. The

Mic indicator will blink and will remain

solid when connected.

NOTES:

• The wireless mics have a working distance

of up to 30 feet/10 meters in open space.

• If there is no audio input to the unit for 20

minutes, the wireless mic connection will

automatically turn off. To reactivate the

connection, turn on the unit and press the

button.

When the wireless mic batteries are low

the battery indicator will flash. Change the

batteries as follows:

1 Unscrew the bottom of the wireless

microphone.

2 Replace the batteries with 2 x "AA"

size/LR6 battery.

3 Screw the bottom of the wireless

microphone back on.

Battery Precautions

The precautions below should be followed when using batteries in

this device:

1. Use only the size and type of batteries specified.

2. Be sure to follow the correct polarity when installing the

batteries as indicated in the battery compartment. Reversed

batteries may cause damage to the device.

3. Do not mix different types of batteries together (e.g. Alkaline

and Carbon Zinc) or old batteries with fresh ones.

4. If the device is not to be used for a long period of time,

remove the batteries to prevent damage or injury from

possible battery leakage.

5. Do not try to recharge batteries not intended to be recharged,

they can overheat and rupture. (Follow battery manufacturer’s

directions.)

6. Rechargeable batteries are to be removed from the product

before being charged.

7. Rechargeable batteries are only to be charged under adult

supervision.

8. Exhausted batteries are to be removed from the product.

9. Batteries shall not be exposed to excessive heat such as

sunshine, fire or the like.

u

— E8 —

Connections

Connect the wired microphone (not included)

into Mic jack u or v (when desired); the

corresponding mic Indicator light will blink.

Connecting optional wired Microphones:

v

u

Energy Saving (Auto Power System-APS)

If there is no audio playback, the unit will automatically enter standby mode after 20

minutes. To resume using the unit, press the / button.

APS is designed to save energy.

— E9 —

Operation

1 Connect the unit and turn it on by

pressing the / button.

2 Insert a USB flash drive with MP3

files into the unit's USB port. Our

Karaoke Store offers a wide range of

downloadable karaoke music.

3 Press the FUNC button repeatedly to

select the USB mode. The display will

show "USb".

Press the / button to start

playback.

Press the / button during playback

to pause the song.

Press and hold the / button to

stop playback.

NOTE: The USB mode requires the flash drive

to be inserted.

4 Adjust the volume to a comfortable

level using the MUSIC VOLUME/MIC

VOLUME control.

Instructions for playing songs from a USB:

v

u

w

x

— E10 —

5 Press the button on the microphone

to turn on the mic.

6 Adjust the microphone volume using

the MUSIC VOLUME/MIC VOLUME

control on the unit or the

+

or

-

buttons on the microphone.

7 SKIP: Press the or button to go

forward or backward one track. Press

and hold the or button to skip

10 tracks.

8

Select a voice effect by pressing the

or button.

9 REPEAT: Press the REPEAT button

once to repeat the current track. Press

twice to repeat all tracks in the current

folder. Press three times to repeat all

tracks. Press the REPEAT button again

to stop the repeat function.

10 Turn off the unit by holding down the

/ button.

Instructions for playing songs from a USB (continued):

Operation

y

U

V

W

X

at

— E11 —

Operation

Instructions for pairing with a Bluetooth device:

1 Connect the unit and turn it on by

pressing the / button.

2 Select the Bluetooth mode by pressing

the /VOCALS OFF button or

repeatedly pressing the FUNC button

until "bt" appears on the display.

3 The unit will automatically search and

pair with a previously paired Bluetooth

device. If no previously paired devices

are available, follow step #4 to pair.

NOTE: To disconnect paired devices and pair

a new device, press and hold the /VOCALS

OFF button.

4 Enable the Bluetooth option in your

device's settings to search for a

discoverable device with a Bluetooth

signal. From the Bluetooth menu, select

"SINGING MACHINE" from the device

results.

Refer to your Bluetooth device's user

manual for detailed instructions.

5 A chime will sound to indicate a

successful pairing.

NOTES:

• If your Bluetooth prompts you for a passcode during the pairing process, please enter

“0000” to connect.

• On some Bluetooth devices, once pairing is completed, select your Bluetooth device as “Use

as Audio Device” or similar.

• If connection is lost after successful pairing, check to make sure the distance between

speaker and Bluetooth-enabled device does not exceed 30 feet/10 meters.

v

w

v

u

3

4

SINGING MACHINE

x

y

— E12 —

Operation

Instructions for pairing with a Bluetooth device (continued):

6 To control your Bluetooth device from

this unit, press the / button to

start playback (music app must be

open). Press the / button during

playback to pause the song.

7 Adjust the volume to your preference

using both the MUSIC VOLUME/MIC

VOLUME control on this unit and the

volume on your Bluetooth device.

8 Press the button on the microphone

to turn on the mic.

9 Toggle the MUSIC VOLUME/MIC

VOLUME control on unit or press the

the

+

or

-

buttons on mic as desired.

Increasing this control will increase the

volume of the microphone.

10 VOCALS: To mute the lead singer on

the recording, press and hold the /

VOCALS OFF button. Press and hold

the /VOCALS OFF button again to

restore the lead singer.

NOTE: The effectiveness of the Vocal off

function may vary depending on the song.

11 Press the or button to select

a voice effect.

U

V

W

X

at

ak

— E13 —

Operation

Instructions for pairing with a Bluetooth device (continued):

12 RECORD YOUR VOCAL

PERFORMANCE:

a.

Press the REC button to start recording

your singing along with the music. The

record indicator will flash.

b. Press the REC button again to stop

recording. The record indicator will

turn off.

NOTE: The recorded audio file will be saved on

the USB drive.

13 Turn off the unit by holding down the

/ button.

al

am

— E14 —

Operation

Instructions for using the AUX IN Jack:

1 Connect the unit and turn it on by

pressing the / button.

2

Connect an external unit to the AUX

IN Jack on the rear of this unit. This

allows audio to be played through your

Singing Machine.

NOTES:

• Set the volume on the external unit to 1/3 or

lower to avoid distortion.

• Skipping files/tracks is not possible when

using an external device with this unit.

3 Select the AUX IN mode by repeatedly

pressing the FUNC button until "AU"

appears on the display.

4 Adjust the volume to your preference

using both the MUSIC VOLUME/MIC

VOLUME control on this unit and the

volume on your external device.

w

u

v

x

— E15 —

Instructions for using the AUX IN Jack (continued):

5 Press the button on the microphone

to turn on the mic.

6 Toggle the MUSIC VOLUME/MIC

VOLUME control on unit or press the

the

+

or

-

buttons on mic as desired.

Increasing this control will increase the

volume of the microphone.

7 Press the or button to select

a voice effect.

8 RECORD YOUR VOCAL

PERFORMANCE:

a.

Press the REC button to start recording

your singing along with the music. The

record indicator will flash.

b. Press the REC button again to stop

recording. The record indicator will

turn off.

NOTE: The recorded audio file will be saved on

the USB drive.

9

Turn off the unit by holding down the

/ button.

Operation

y

U

UV

W

X

— E16 —

Operation

Name Effect Description

Basic Pitch Silky smooth & balanced reverb & echo; a great all around go-to

vocal enhancer

Alt-Rock Queue up your fave alternative & rock tunes with this crowd-

pleasing vocal effect

Reggae-Tone Enhanced echo makes voices shine especially while singing reggae

and reggaeton

Grunge Unmistakably gritty, great for rock, alt, pop and just making your

voice sound cool

Hip-Hop Big room echo & reverb, great for hip-hop, rap and R&B

Oldtown Rd A touch of echo with added vocal boost that’s great for belting out

country tunes

Up to Mars Big echo, good for a wide range of songs from ballads to funk

Pitch Tune C Pitch Tune like the pros with this pitch enhancing effect for singing

in the key of C

Pitch Tune D Pitch Tune & enhancing effect for singing in the key of D

Pitch Tune E Pitch Tune & enhancing effect for singing in the key of E

Pitch Tune Chromatic Pitch Tune & enhancing effect (Chromatic Scale)

Nosebleed Seats Did someone say sold out stadium shows?

Radio Great for singing 90’s Rock or for making big announcements

Doubling Classic & versatile doubling effect

Doubling Tuned Voice doubling with pitch tuning enhancement

Radio Tuned Classic radio effect with pitch tuning enhancement

Squeeze A fun, voice morphing effect that tweaks voices to a higher pitch

Diva Add a sassy touch to voices

Voice Drop Deepens voices for a fun effect

Deep Deep Tunes voices deep & low

Robot Machiney & robotic

Chipmunk Mousey, squeaky fun voice effect

Sound Effects

— E17 —

Troubleshooting Guide

If you encounter any issues with this unit, try the following troubleshooting steps before

seeking service:

No Power:

• Press the / button to turn the unit on.

• Charge the unit if the battery is depleted.

• Check the secure connection of the USB jack at the back of the unit.

• Connect the unit to a different outlet.

• The normal function of the product may be disturbed by strong Electro-Magnetic

Interference. If so, simply restart the product to resume normal operation by following

the instruction manual. In the event the function does not resume, please use the machine

in another part of the home.

No Sound – General:

• Increase the Master Volume if set to minimum.

• Press the FUNC button to select the correct function.

• If using an external device, adjust its volume.

No Sound from the Microphone:

• Replace the batteries in the wireless microphone.

• Ensure the microphone is turned on.

• Increase the MIC VOLUME if set to minimum.

Bluetooth Pairing or Connection Issues:

• Turn off any other Bluetooth devices to avoid accidental pairing.

• Activate the Bluetooth function on your device (refer to the Bluetooth device user's

manual or page E11 for instructions).

• Restart pairing by pressing and holding the /VOCALS OFF button to enter pairing mode.

Music Unavailable on the Unit after Bluetooth Connection:

• Ensure that your Bluetooth device supports the A2DP Bluetooth profile.

• Adjust the volume or unmute the external Bluetooth device.

• Make sure the music application is open on your device.

— E18 —

Specifications

AUDIO

OUTPUT POWER (MAXIMUM)..................................................................................10 Watts (RMS)

OUTPUT IMPEDANCE .................................................................................................................. 4 Ohms

USB

Format.................................................................................................................................................FAT32

Maximum Capacity............................................................................................................................32GB

BLUETOOTH

Bluetooth Version ...............................................................................................................................V5.0

Working Distance .......................................... Up to 30 feet/10 meters measured in open space

CONNECTING JACKS

Microphone .................................................................................................................................... 6.3mm

AUX IN SECTION ..............................................................................3.5 mm Stereo Headphone Jack

GENERAL

Power .....................................................................................................................Type-C USB 5VDC, 1A

Dimensions ............................................................. 7.8 x 7.8 x 9.7 inches (19.8 x 19.8 x 24.6cm)

Weight ............................................................................................................................ 1.4 Lbs (3.1 kgs)

Wireless Microphone .............................................................. 2.4GHz band Dynamic Microphone

Specifications are subject to change without notice

The Bluetooth® word mark and logos are registered trademarks

owned by Bluetooth SIG, Inc. and any use of such marks by

The Singing Machine Company, Inc. is under license. Other

trademarks and trade names are those of their respective

owners.

— S1 —

ADVERTENCIA DE GOTEO: Este producto no se podrá exponer a goteo o

salpicaduras, y no se colocará ningún objeto lleno con líquidos, como jarrones,

encima del producto.

ADVERTENCIA DE VENTILACIÓN: La ventilación normal del producto no se

bloqueará si se le da el uso previsto.

Advertencia: Los cambios o las modificaciones a esta unidad que no fueron

expresamente aprobados por la parte responsable del cumplimiento de las

normas pueden anular la autoridad del usuario para operar el equipo.

Advertencias

Información importante sobre seguridad

1. Lea estas instrucciones.

2. Conserve estas instrucciones.

3. Preste atención a todas las advertencias.

4. Siga todas las instrucciones.

5. No utilice este artefacto cerca del agua.

6. Límpielo únicamente con un paño seco.

7. No obstruya las aberturas para ventilación. Instálelo de acuerdo

con las instrucciones del fabricante.

8. No instale cerca de fuentes de calor, como radiadores, rejillas de

calefacción, estufas u otros aparatos (incluso amplificadores)

que produzcan calor.

9. No desafíe el fin de seguridad del enchufe polarizado o de

conexión a tierra. Un enchufe polarizado tiene dos clavijas y una

es más ancha que la otra. El enchufe de conexión a tierra tiene

dos clavijas, y una tercera punta a tierra. La clavija ancha o la

tercera punta se suministran para su seguridad. Si el enchufe

suministrado no coincide con su tomacorriente, consulte con un

electricista para reemplazar el tomacorriente obsoleto.

10. Evite pisar o apretar el cable de alimentación, especialmente en

los enchufes, tomacorrientes y en el punto por donde salen del

artefacto.

11. Utilice sólo los complementos y accesorios especificados por el

fabricante.

12. Utilice la unidad sólo con el carro, soporte, trípode, repisa o mesa

recomendados por el fabricante, o que se vendan junto con el

producto. Cuando se utiliza un carro, tenga

cuidado cuando mueva el carro y artefacto

junto a para evitar lesiones producidas por la

caída del producto.

13. Desenchufe este artefacto durante las

tormentas eléctricas o cuando no se lo utilice

durante períodos prolongados.

14. Derive todas las reparaciones al personal

de reparaciones calificado. Es necesario reparar el artefacto

cuando se encuentra dañado; por ejemplo, cuando el cable

de suministro de energía o el enchufe están dañados, cuando

se derrama líquido sobre la unidad o caen objetos dentro del

mismo, cuando el producto ha estado expuesto a la lluvia o a la

humedad, cuando no funciona con normalidad o cuando se ha

caído.

15. ADVERTENCIA: Para reducir el riesgo de incendio o descarga

eléctrica, no exponga este artefacto a la lluvia o la humedad. No

coloque objetos llenos de agua, como jarrones, sobre el aparato.

16. El enchufe de conexión de CA se utiliza como dispositivo de

desconexión eléctrica y deberá estar siempre accesible y en

funcionamiento durante el uso previsto. Para desconectar

completamente el aparato de la electricidad, el enchufe de

conexión deberá quitarse por completo del tomacorriente de

CA.

17. PRECAUCIÓN: Para reducir el riesgo de incendio o explosión

no exponga las baterías al calor excesivo, como al rayo del sol,

fuego u otras fuentes de calor.

ADVERTENCIA SOBRE

EL CARRO PORTÁTIL

(símbolo provisto por RETAC)

PRECAUCIÓN: PARA REDUCIR EL RIESGO DE DESCARGAS ELÉCTRICAS,

NO QUITE LA CUBIERTA (NI LA TAPA POSTERIOR) NO HAY PIEZAS

REPARABLES POR EL USUARIO DENTRO. DERIVE LAS REPARACIONES A

PERSONAL DE SERVICIO CALIFICADO.

Las marcas de Precaución se ubican en el panel inferior.

TENSIÓN PELIGROSA: La luz intermitente con símbolo de

flecha dentro de un triángulo pretende alertar al usuario de la

presencia de tensión peligrosa no aislada, dentro del paquete

del producto, que puede ser de magnitud suficiente para

constituir un riesgo de descarga eléctrica para las personas.

ADVERTENCIA: PARA EVITAR INCENDIOS O PELIGROS DE DESCARGA, NO

EXPONGA ESTA UNIDAD A LA LLUVIA O HUMEDAD.

ATENCIÓN: El signo de exclamación dentro de un triángulo

pretende alertar al usuario de la presencia de instrucciones

importantes de operación y mantenimiento (reparaciones) en

el material que acompaña a este producto.

AVISO DE LA FCC: Este equipo puede generar o usar energía de radio

frecuencia. Los cambios o modificaciones realizados en el aparato pueden

provocar interferencia perjudicial, a menos que dichas modificaciones estén

autorizadas en el manual de instrucciones. El usuario puede perder toda

autoridad para operar el equipo si realiza cambios o modificaciones sin

autorización.

Este aparato cumple con la parte 15 de las Normas de la FCC. El

funcionamiento está sujeto a las dos condiciones que figuran a continuación:

(1) Es probable que no cause interferencia perjudicial y (2) deberá aceptar

cualquier interferencia recibida, incluyendo la interferencia que pueda llegar

a causar un funcionamiento indeseado.

NOTA: Este equipo fue probado y se concluyó que cumple con los límites

establecidos para los dispositivos digitales Clase B, de acuerdo con el

Apartado 15 de las normas de la FCC. Estos límites fueron pensados para

proporcionar protección razonable ante la interferencia perjudicial en una

instalación residencial. Este equipo genera, usa y puede emitir energía

de radio frecuencia y, si no se lo instala y utiliza de conformidad con las

instrucciones, puede causar interferencia perjudicial a las comunicaciones

radiales. No obstante, no existe ninguna garantía de que no se produzca

interferencia en una instalación en particular. Si este equipo provoca

interferencia perjudicial a la recepción de radio o televisión, lo cual puede

determinarse apagando y encendiendo el equipo, el usuario puede intentar

corregir la interferencia de alguna/s de las siguientes maneras:

• Reoriente la antena receptora o ubíquela en otro lugar.

• Aumente la distancia entre el equipo y el receptor.

• Conecte el equipo a un tomacorriente de un circuito distinto al que está

conectado el receptor.

• Consulte al distribuidor o a un técnico experimentado de radio y televisión

para que lo asesore.

La información de clasificación se encuentra en la parte posterior de la

unidad.

Declaraciones de advertencia de exposición a RF:

Este equipo cumple con los límites de exposición a la radiación de la FCC

establecidos para ambiente incontrolado.

PRECAUCIÓN

RIESGO DE DESCARGA ELÉCTRICA.

NO ABRIR

PRECAUCIÓN: PARA EVITAR DESCARGAS ELÉCTRICAS, INSERTE

COMPLETAMENTE UNA HOJA ANCHA DEL ENCHUFE A LA RANURA

ANCHA.

La page est en cours de chargement...

Singing Machine SML668G Manuel utilisateur

Singing Machine SML668G Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents