SingingMachine ISM2040 Manuel utilisateur

TM

ISM2040

INSTRUCTION MANUAL/

MANUAL DE INSTRUCCIONES/

MODE D’EMPLOI

www.singingmachine.com

The Singing Machine® is a registered trademark of The Singing Machine Co., Inc.

The Singing Machine® es marca registrada de The Singing Machine Co., Inc.

The Singing Machine® est une marque déposée de The Singing Machine Co., Inc.

— E1 —

Important Safety Information

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all Instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in

accordance with the Manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. When the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete

outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with a cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or has been dropped.

15. WARNING: To reduce the risk of fire or electric shock, do not

expose this apparatus to rain or moisture. Do not place objects

filled with water, such as a vase, on the apparatus.

16. The AC mains plug is used as the power disconnect device

and it should remain readily accessible and operable during

intended use. In order to completely disconnect the apparatus

from power, the mains plug should be completely removed

from the AC outlet socket.

17. CAUTION: To reduce the risk of fire or explosion, do not expose

batteries to excessive heat such as sunshine, fire or other

heat sources.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

DANGEROUS VOLTAGE: The lightning flash with arrowhead

symbol within an equilateral triangle is intended to alert the

user to the presence of uninsulated dangerous voltage within

the product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

ATTENTION: The exclamation point within an equilateral

triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions

in the literature accompanying this product.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Warnings

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THIS UNIT TO RAIN OR MOISTURE.

DRIPPING WARNING: This product shall not be exposed to dripping or

splashing, and no objects filled with liquids, such as vases, shall be placed

on the product.

VENTILATION WARNING: The normal ventilation of the product shall not

be impeded for intended use.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF

PLUG TO WIDE SLOT AND FULLY INSERT.

FCC WARNING: This equipment may generate or use radio frequency

energy. Changes or modifications to this equipment may cause harmful

interference unless the modifications are expressly approved in the

instruction manual. The user could lose the authority to operate this

equipment if an unauthorized change or modification is made.

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The rating information is located at the bottom of the unit.

Warning: Changes or modifications to this unit not expressly approved

by the party responsible for compliance could void the user’s authority to

operate the equipment.

— E2 —

Included

Please make sure that the following items are included.

Wireless Microphone

Base

Main Unit

Cradle with mic holders

(Detachable)

Extendable Mic stand

AC Adapter

Manual

Mic 1

Mic 2

— E3 —

Assembly

Not for use with other microphone stands. Only lift unit from bottom base. Use caution

when placing larger-sized devices in holder.

v

x

w

1

Insert and rotate clockwise to

tighten the Main unit onto the

Base.

2

Lift the rubber cover on the top of

the Main unit. Insert the Mic stand

into the Main unit and tighten it.

3

Insert and rotate to tighten the

Cradle with Mic holders on the Mic

stand.

4

Untighten the mic stand locker(s)

to adjust to a suitable height.

Retighten the locks to hold in

position.

All-in-one assembly

— E4 —

Assembly

u

w

v

Split type assembly

1

Insert the Mic stand into the Base

and tighten it.

2

Insert and rotate to tighten the

Cradle with Mic holders on the Mic

stand.

3

Untighten the mic stand locker(s)

to adjust to a suitable height.

Retighten the locks to hold in

position.

4

Leave the main unit within 30

feet/10 meters distance as a

speaker.

NOTE: Always remember to put the rubber

cover back in place.

— E5 —

Location of Controls

1. Cradle

2. Mic Holders

3. MIC stand locks

4. Speaker

5. Mic Volume/VOCAL OFF

Control

6. / (Bluetooth/ Play/

Pause Button

7. / (LIGHTS/On/

Standby) button

8. VOCAL EFFECTS Control

9. PERFECT PITCH Button

10. MUSIC VOLUME

Control

11. RECORD Button

12. PLAYBACK Button

13. EFFECTS STRENGTH

Control

14 Display

15. DC In Jack

16. Mic 3 Jack

17. AUX In Jack

18. Handle

19. Wireless Mic battery

indicator

20. Wireless Mic ON/OFF

button

21. Bluetooth indicator

22. Battery indicator

23. Mic 1 indicator

(wireless)

24. Mic 2 indicator

(wireless)

25. Mic 3 indicator (wired)

u

v

x

w

y

U

W

V

X

at

ak

al

am

an

TOP

as bt

WIRELESS MIC

bk

bm

bl

an

bo

bn

1

2

3

DISPLAY

ao ap aq

REAR

ar

— E6 —

Rechargeable Battery

This unit comes with a built-in rechargeable battery pack that will allow the unit to be used

without being connected to AC power. The rechargeable battery pack must NOT to be

replaced by the user.

To optimize the battery life, we recommend to charge the unit once a month. When the

battery indicator on the display flashes slowly, recharge the unit by following the steps below:

1

Insert the AC power cord into a

conveniently located AC outlet

having 120V, 60Hz.

2

Allow the unit to charge for

approximately 8 hours for a full

charge. When fully charged,

the battery indicator will light

solid.

3

Disconnect the AC cord and

the fully charged unit can

be used for approximately

4-10 hours depending on the

function chosen.

Attention: The sound volume will adjust automatically when the battery is not full.

Recycling and Disposal Information:

• Do not dispose of electronic devices or any of their components.

(especially batteries and LCD displays) in your municipal trash collection.

• Consult your local waste management authority or a recycling organization like Earth911.

com to find an electronics recycling facility in your area.

CAUTION: Rechargeable batteries must be recycled or disposed of properly.

Energy Saving (Auto Power System-APS)

The unit will automatically enter the Standby mode after 30 minutes in the following

situations:

1. There is no audio playback;

2. The playback of external music player had been stopped but the audio cable is still plugged

into the LINE IN jack.

The unit can be resumed to turn on by pressing the / button.

APS is for energy saving purposes.

— E7 —

NOTES:

• Make all connections prior to plugging the AC adaptor into a power outlet.

• The AC adaptor has a polarized plug that fits into the AC outlet only one way. If the plug

does not fit properly, turn it over and try again. Do not force and do not file or cut the wide

blade.

• The provided AC adapter can only support to charge the built-in rechargeable battery.

Connections

Insert the AC power cord into a

conveniently located AC outlet having

120V AC, 60Hz.

Charging the unit

Connecting the Wireless Microphone(s)

Rotate the MIC VOLUME/VOCAL OFF

control, the Mic indicator 1 and 2 will

appear in display and flash.

Slide the Wireless Mic’s ON/MUTE/OFF

u

switch to the ON position. The Mic

indicator 1 or 2 will light solid.

NOTES:

• The working distance up to 30 feet/10

meters measured in open space.

• If there is no audio input for 15 minutes,

the wireless mics connection will

automaticlly turn off. Rotate the MIC

VOLUME/VOCAL OFF control to

reactivate the connection.

u

— E8 —

Changing the Wireless Microphone’s Battery

When the wireless mic battery indicator

flashes, it shows it is out of power. Change

the batteries as follows:

1

Unscrew the bottom of wireless

microphone.

2

Replace the batteries with 2 x "AA"

size/LR6 battery.

3

Replace the bottom of wireless

microphone and screw it on.

Connections

Battery Precautions

The precautions below should be followed when using batteries in

this device:

1. Use only the size and type of batteries specified.

2. Be sure to follow the correct polarity when installing the

batteries as indicated in the battery compartment. Reversed

batteries may cause damage to the device.

3. Do not mix different types of batteries together (e.g. Alkaline

and Carbon Zinc) or old b

atteries with fresh ones.

4. If the device is not to be used for a long period of time,

remove the batteries to prevent damage or injury from

possible battery leakage.

5. Do not try to recharge batteries not intended to be recharged,

they can overheat and rupture. (Follow battery manufacturer’s

directions.)

6. Rechargeable batteries are to be removed from the product

before being charged.

7. Rechargeable b

atteries are only to be charged under adult

supervision.

8. Exhausted batteries are to be removed from the product.

9. Batteries shall not be exposed to excessive heat such as

sunshine, fire or the like.

Connecting the optional wired Microphone

Connect the wired microphone (not

included) into Mic jack

u

(when desired).

NOTE: Maximum of two microphones

(wired or wireless) connected to the

unit at one time. After inserting the

wired microphone (Mic 3), the wireless

microphone 1 (Mic 1) will be automatically

turned off.

u

— E9 —

Connections

Lights Mode

u

There are 5 built-in light mode. Repeatly press

/ button to switch between lighting

effects.

Connecting to AUX IN Jack

Cradle

Connect an external device by using an

appropriate cable (3.5mm audio cable not

included) as shown.

NOTE:

See page E13 to select and use the Aux In

function.

PULL

— E10 —

Operation

Using a Bluetooth Device

u

v

Please connect your Music Device

Your Music Device is connected

3

4

Please connect your Music Device

Your Music Device is connected

1

Connect the unit as described

previously. Press the / button

to turn the unit on.

2

“bt” and bluetooth indicator will

appear in display and flash.

The unit automatically searches and

pairs a previously paired Bluetooth

device (if previously paired). If

no previously paired devices are

present and you cannot find this

unit on your bluetooth compatible

device’s search list. Press and

hold the / button; the “PR”

and bluetooth indicator will start

flashing for 60 seconds.

NOTE: You can also press and hold the

button to disconnect any paired devices in

order to pair another device.

3

Turn on your device’s Bluetooth

option in settings to search for

a discoverable device with a

Bluetooth signal. Select “SINGING

MACHINE” from the device results

on the Bluetooth menu.

NOTE: Also refer to the user manual of your

Bluetooth device for detailed instructions.

4

“

bt

” and bluetooth indicator will

light solid and a successful pairing

sound will be heard.

NOTES:

• If your Bluetooth prompts you for a passcode during the pairing process, please enter

“0000” to connect.

• On some Bluetooth devices, once pairing is completed, select your Bluetooth device as “Use

as Audio Device” or similar.

• If connection is lost after successful pairing, check to make sure the distance between

speaker and Bluetooth-enabled device does not exceed 30 feet/10 meters.

• “Bluetooth” will blink on TV screen, and will stop blinking after successful connection.

— E11 —

U

y

Operation

Using a Bluetooth Device (Continued)

V

W X

5

To control your Bluetooth device

from this unit, press the /

button to start playback. Press

the / button during playback

to pause the song.

6

Adjust the volume to a

comfortable level using the

MUSIC VOLUME control on this

unit as well as the volume on your

Bluetooth device.

7

Slide the Wireless Mic’s ON/

MUTE/OFF switch to the ON

position.

NOTE: Slide to MUTE position is to

temporary stop the microphone input.

8

Adjust the MIC VOLUME/

VOCAL OFF control as

desired. Increasing this control

will increase the volume of

microphones.

9

RECORD YOUR SINGING

PERFORMANCE

During music playback, press the

RECORD button to record your

singing and the music, "REC" will

appear in display and light solid.

Press the RECORD button again

to stop recording, the "REC" will

turn off.

This unit is able to record for 5

minutes. It will also stop recording

automatically after 5 minutes and

the "REC" will turn off.

NOTE: Please note that each time when

the new recording is being recorded, the

existing recording will be deleted.

— E12 —

Using a Bluetooth Device (Continued)

Operation

10

PLAYBACK YOUR SINGING

PERFORMANCE

To playback your singing

performance, you can press the

PLAYBACK button. "PB" will

appear on the display and light

solid. Press again to stop. Press

and hold the PLAYBACK button

to delete the recorded track.

11

Slide the VOCAL EFFECTS

control up or down to select the

vocal effects.

12

Slide the EFFECTS STRENGTH

control up or down to adjust

the level of the selected vocal

effects.

13

Repeatedly press the PERFECT

PITCH button to switch between

the different levels of voice pitch.

Display will show level.

NOTE: This function is only available for

either Wireless Mic 1 or Mic 3.

14

To sing without the lead singer

on the recording, press the MIC

VOLUME/VOCAL OFF control.

To resume the lead singer, press

again.

NOTE: Lead vocal removal might work

better on some songs than others.

15

Press and hold the / button

to turn off the unit.

ak

at

am

ao

an

al

— E13 —

Using the AUX IN Jack

1

Connect the unit as described

previously. Press the /

button to turn the unit on.

2

Connect the external device

by using an appropriate cable

(3.5mm audio cable not included)

to the AUX IN Jack on the rear

of this unit as previous described.

When connected, the Aux

function is automatically selected,

"AUX" will appear in display and

light solid.

NOTES:

• It is highly recommended to set the

volume on the auxiliary unit to 1/3 or

lower to avoid distortion.

• All controlling functions are not possible

on this unit when using an external

device.

3

Adjust the volume to a

comfortable level using the

MUSIC VOLUME control on this

unit or your external device’s

volume control.

Operation

u

v

w

— E14 —

x

4

Slide the Wireless Mic’s ON/

MUTE/OFF switch to the ON

position.

NOTE: Slide to MUTE position is to

temporary stop the microphone input.

5

Adjust the MIC VOLUME/

VOCAL OFF control as desired.

Increasing this control will

increase the volume of both

microphones.

6

RECORD YOUR SINGING

PERFORMANCE

During music playback, press the

RECORD button to record your

singing and the music, "REC" will

appear in display and light solid.

Press the RECORD button again

to stop recording, the "REC" will

turn off.

This unit is able to record for 5

minutes. It will also stop recording

automatically after 5 minutes and

the "REC" will turn off.

NOTE: Please note that each time when

the new recording is being recorded, the

existing recording will be deleted.

7

PLAYBACK YOUR SINGING

PERFORMANCE

To playback your singing

performance, you can press the

PLAYBACK button. "PB" will

appear on the display and light

solid. Press again to stop. Press

and hold the PLAYBACK button

to delete the recorded track.

Using the AUX IN Jack (Continued)

Operation

y U

V

— E15 —

Operation

Using the AUX IN Jack (Continued)

8

Slide the VOCAL EFFECTS

control up or down to select the

vocal effects.

9

Slide the EFFECTS STRENGTH

control up or down to adjust

the level of the selected vocal

effects.

10

Repeatedly press the PERFECT

PITCH button to switch between

the different levels of voice pitch.

Display will show level.

NOTE: This function is only available for

either Wireless Mic 1 or Mic 3.

11

Press and hold the / button

to turn off the unit.

W

at

ak

X

— E16 —

Name Display Effect Description

None --- No voice effects applied

Basic Pitch 1 Silky smooth & balanced reverb & echo; a great all

around go-to vocal enhancer

Billie Eyelash 2 Queue up Bad Guy & let it rip with this harmonized choir

effect that is perfect for Alternative and Rock singing

Phil the Air Tonight 3 Heavy on the reverb & echo with delicate feedback &

flanger effect for a lovely sound perfect for 80's hits

Grunge 4 Unmistakably gritty, great for rock, alt, pop and just

making your voice sound cool

Reggae-Tone 5 Enhanced echo and choir makes voices shine especially

while singing reggae and reggaeton

Hip-Hop 6 Big room echo & reverb with a smooth chorus

Oldtown Rd 7 A touch of echo with added vocal boost that's great for

belting out country tunes

Diva 8 Take your voice to new heights with this octave booster

Doo-Wop 9 Smooth harmony adds some bass backup to your voice

Electronica 10 Punchy and unique, perfect for pop, EDM and making

heads turn

Up to Mars 11 Big echo and chorus good for a wide range of songs from

ballads to funk

Anthems 12 Lots of echo and reverb for when your voice needs to be

BIG

Nosebleed Seats 13 Did someone say sold out stadium shows?

Voice of an Angel 14 Have your own angelic choir singing along with this lovely

chorus effect

4 of a Kind 15 It's like having a few more singers harmonize along with

your vocals

Ballad Rock 16 Crank up your favorite guilty pleasure ballad and rock it

out for that special someone in the audience

Bad Trip 17 Wild & fun chorus effect

Laser 18 Crazy & silly vocal laser beams

Warp Speed 19 Bouncy & echos, lots of fun

Barry Deep 20 Oh baby, that's a deep voice

Pitch Lab Vocal Enhancement Guide

— E17 —

Troubleshooting Guide

Should this unit exhibit a problem, check the following before seeking service:

No Power

• Power is not on; press the / (LIGHTS/ON/STANDBY) button to turn power on.

• The unit has no battery left. Connect to AC power to recharge the battery.

• The normal function of the product may be disturbed by strong Electro-Magnetic

Interference. If so, simply restart the product to resume normal operation by following

the instruction manual. In case the function could not resume, please use the product in

another location.

No Sound – General

• Music Volume is set to minimum; raise volume.

• If using an external device, raise the volume.

No sound from the microphone

• The wireless microphone has no battery left. Change the batteries.

• Make sure the mic’s ON/OFF switch is set to the ON position.

• Make sure the MIC VOLUME/VOCAL OFF control is not set too low.

The Bluetooth device cannot be paired or connected with the unit

• Ensure any other Bluetooth devices are turned off to avoid accidental pairing.

• You have not activated the Bluetooth function of your device; see page E10 or refer to the

Bluetooth device user’s manual.

• The system is not in pairing mode; press and hold the / button to restart pairing.

The Music is not available on the unit after successfully connecting the Bluetooth

• Ensure your Bluetooth device can support the A2DP Bluetooth profile.

• The volume on the external Bluetooth device is set too low or muted; raise as desired.

— E18 —

Specifications

AUDIO

Output Power ..................................................................................................................70 Watts (RMS)

BLUETOOTH

Bluetooth Version .................................................................................................................................V5.0

Working Distance ............................................ Up to 30 feet/10 meters measured in open space

CONNECTING JACKS

Microphone ...................................................................................................................................... 6.3mm

Aux In ............................................................................................................................ 3.5mm Stereo Jack

GENERAL

Power ...................................................................................................................... 100-240V, 50/60Hz

Output ............................................................................................................. DC9V 1A Positive Center

Dimensions:

Main Unit only .................................................. 10.3 x 10.3 x 12.6 inches (26.2 x 26.2 x 32cm)

Mic stand only .................................... Adjustable height max. 57.0 H inches/ 145cm (optional)

Main unit + Mic stand ...................... Adjustable height max. 66.9 H inches/ 170cm (optional)

Base ....................................................................... 11.8 x 11.8 x 1.1 inches (30.0 x 30.0 x 2.7cm)

Weight - Main Unit only ............................................................................................. 9.7 Lbs (4.4 kgs)

Mic Stand only ........................................................................................... 9.9 Lbs (4.5 kgs)

Wireless Microphone ........... VHF band (204.5MHz/208.5 MHz Freq) Dynamic Microphone

Specifications are subject to change without notice.

The Bluetooth® word mark and logos are registered trademarks

owned by Bluetooth SIG, Inc. and any use of such marks and

logos by The Singing Machine Company, Inc. is under license.

Other trademarks and trade names are those of their respective

owners.

— S1 —

TENSIÓN PELIGROSA: La luz intermitente con símbolo de

flecha dentro de un triángulo pretende alertar al usuario de la

presencia de tensión peligrosa no aislada dentro del paquete

del producto, que puede ser de magnitud suficiente para

constituir un riesgo de descarga eléctrica para las personas.

ATENCIÓN: El signo de exclamación dentro de un triángulo

pretende alertar al usuario de la presencia de instrucciones

importantes de operación y mantenimiento (reparaciones) en

el material que acompaña a este producto.

Información importante sobre seguridad

1. Lea estas instrucciones.

2. Conserve estas instrucciones.

3. Preste atención a todas las advertencias.

4. Siga todas las instrucciones.

5. No utilice este artefacto cerca del agua.

6. Límpielo únicamente con un paño seco.

7. No obstruya las aberturas para ventilación. Instálelo de acuerdo

con las instrucciones del fabricante.

8. No instale cerca de fuentes de calor, como radiadores, rejillas de

calefacción, estufas u otros aparatos (incluso amplificadores)

que produzcan calor.

9. No desafíe el fin de seguridad del enchufe polarizado o de

conexión a tierra. Un enchufe polarizado tiene dos clavijas y una

es más ancha que la otra. El enchufe de conexión a tierra tiene

dos clavijas, y una tercera punta a tierra. La clavija ancha o la

tercera punta se suministran para su seguridad. Si el enchufe

suministrado no coincide con su tomacorriente, consulte con un

electricista para reemplazar el tomacorriente obsoleto.

10. Evite pisar o apretar el cable de alimentación, especialmente en

los enchufes, tomacorrientes y en el punto por donde salen del

artefacto.

11. Utilice sólo los complementos y accesorios especificados por el

fabricante.

12. Utilice la unidad sólo con el carro, soporte, trípode, repisa o

mesa recomendados por el fabricante, o que se vendan junto

con el producto. Cuando se utiliza un carro, tenga cuidado

cuando mueva el carro y artefacto junto

a para evitar lesiones producidas por la

caída del producto.

13. Desenchufe este artefacto durante las

tormentas eléctricas o cuando no se lo

utilice durante períodos prolongados.

14. Derive todas las reparaciones al personal

de reparaciones calificado. Es necesario

reparar el artefacto cuando se encuentra

dañado; por ejemplo, cuando el cable de suministro de energía

o el enchufe están dañados, cuando se derrama líquido sobre la

unidad o caen objetos dentro del mismo, cuando el producto ha

estado expuesto a la lluvia o a la humedad, cuando no funciona

con normalidad o cuando se ha caído.

15. ADVERTENCIA: Para reducir el riesgo de incendio o descarga

eléctrica, no exponga este artefacto a la lluvia o la humedad. No

coloque objetos llenos de agua, como jarrones, sobre el aparato.

16. El enchufe de conexión de CA se utiliza como dispositivo de

desconexión eléctrica y deberá estar siempre accesible y en

funcionamiento durante el uso previsto. Para desconectar

completamente el aparato de la electricidad, el enchufe de

conexión deberá quitarse por completo del tomacorriente de

CA.

17. PRECAUCIÓN: Para reducir el riesgo de incendio o explosión

no exponga las baterías al calor excesivo, como al rayo del sol,

fuego u otras fuentes de calor.

Advertencias

PRECAUCIÓN: PARA REDUCIR EL RIESGO DE DESCARGAS

ELÉCTRICAS, NO QUITE LA CUBIERTA (NI LA TAPA POSTERIOR). NO

HAY PIEZAS REPARABLES POR EL USUARIO ADENTRO. DERIVE LAS

REPARACIONES A PERSONAL DE SERVICIO CALIFICADO.

PRECAUCIÓN: PARA EVITAR DESCARGAS ELÉCTRICAS, INSERTE

COMPLETAMENTE UNA HOJA ANCHA DEL ENCHUFE A LA RANURA

ANCHA.

ADVERTENCIA: PARA EVITAR INCENDIOS O PELIGROS DE DESCARGA,

NO EXPONGA ESTA UNIDAD A LA LLUVIA O HUMEDAD.

AVISO DE LA FCC: Este equipo puede generar o usar energía de radio

frecuencia. Los cambios o modificaciones realizados en el aparato pueden

provocar interferencia perjudicial, a menos que dichas modificaciones

estén autorizadas en el manual de instrucciones. El usuario puede perder

toda autoridad para operar el equipo si realiza cambios o modificaciones sin

autorización.

Este aparato cumple con la parte 15 de las Normas de la FCC. El

funcionamiento está sujeto a las dos condiciones que figuran a continuación:

(1) Es probable que no cause interferencia perjudicial y (2) deberá aceptar

cualquier interferencia recibida, incluyendo la interferencia que pueda llegar

a causar un funcionamiento indeseado.

NOTA: Este equipo fue probado y se concluyó que cumple con los límites

establecidos para los dispositivos digitales Clase B, de acuerdo con el

Apartado 15 de las normas de la FCC. Estos límites fueron pensados para

proporcionar protección razonable ante la interferencia perjudicial en una

instalación residencial. Este equipo genera, usa y puede emitir energía de radio

frecuencia y, si no se lo instala y utiliza de conformidad con las instrucciones,

puede causar interferencia perjudicial a las comunicaciones radiales. No

obstante, no existe ninguna garantía de que no se produzca interferencia en

una instalación en particular. Si este equipo provoca interferencia perjudicial

a la recepción de radio o televisión, lo cual puede determinarse apagando y

encendiendo el equipo, el usuario puede intentar corregir la interferencia de

alguna/s de las siguientes maneras:

• Reoriente la antena receptora o ubíquela en otro lugar.

• Aumente la distancia entre el equipo y el receptor.

• Conecte el equipo a un tomacorriente de un circuito distinto al que está

conectado el receptor.

• Consulte al distribuidor o a un técnico experimentado de radio y

televisión para que lo asesore.

La información de clasificación está ubicada en la parte inferior de la unidad.

Advertencia: Los cambios o modificaciones efectuadas a esta unidad que no

fueron expresamente aprobados por la parte responsable del cumplimiento,

podrían anular la autoridad del usuario para operar el equipo.

ADVERTENCIA DE GOTEO: Este producto no se podrá exponer a goteo o

salpicaduras, ni se podrá colocar encima del producto ningún objeto lleno

con líquidos, como jarrones.

ADVERTENCIA DE VENTILACIÓN: La ventilación normal del producto no se

debe bloquear para el uso previsto.

PRECAUCIÓN

RIESGO DE DESCARGA ELÉCTRICA

NO ABRIR

La page charge ...

SingingMachine ISM2040 Manuel utilisateur

SingingMachine ISM2040 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents