Wacker Neuson LTV6L Manuel utilisateur

LTV4K, LTV6K

LTV6L, LTV8K

Type

Document

Date

Revision

Language

LTV4K, LTV6K, LTV6L, LTV8K

5100030418

0121

07

EN-FR

Operator’s Manual

Notice d'emploi

Light Tower

Tour d’éclairage

Copyright

notice

on America Corporation

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any other

type of reproduction is prohibited without express written permission from Wacker

Neuson America Corporation.

Any type of reproduction or distribution not authorized by Wacker Neuson America

Corporation represents an infringement of valid copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson America Corporation

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

wc_tx004643en.fm 3

CALIFORNIA Proposition 65 Warning

WARNING

The engine exhaust from this product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING

Diesel engine exhaust and some of its constituents are known to the State of

California to cause cancer, birth defects, and other reproductive harm.

WARNING

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

WARNING

Batteries, battery posts, terminals and related accessories contain lead and lead

compounds, and other chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

CALIFORNIA Proposition 65 Warning Proposition 65 Warning

4 wc_tx004643en.fm

This page is intentionally left blank.

wc_tx004428en.fm

5

LTV

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson America Corporation and must be followed during installation,

operation, and maintenance of the machines.

Machine identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number (S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine

documentation

■ From this point forward in this documentation, Wacker Neuson America

Corporation will be referred to as Wacker Neuson.

■ Keep a copy of the Operator’s Manual with the machine at all times.

■ For spare parts information, please see your Wacker Neuson Dealer, or visit

the Wacker Neuson website at http://www.wackerneuson.com/.

■ When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Serial Number:

wc_gr013759

215429215429

R

51000314545100031454

For electrical

equipment only.

Pour material

electrique seulement.

lbs

Item No.

Type/Model

Serial No.

Rev.

MAX AMB 40~C

RPMhz

MON/YR

MADE IN USA

kW

kg

V

n

A

P. F .

wc_tx004428en.fm

6

LTV

Expectations for information in this manual

■ This manual provides information and procedures to safely operate and

maint

ain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructi

ons

desc

ribed in this manual

.

■ Wacker Neuson expressly reserves the right to make technical modifications,

even wi

thout notice, which improve the performance or safety standards of it

s

machi

nes.

■ The information contained in this manual is based on machines manufactur

ed

up until the time of publication. Wacker Neuson reserves the right to change any

por

tion of this information without notice.

■ The illustrations, parts, and procedures in this manual refer to Wack

er Neuson

fa

ctory-installed components. Your machine may vary depending on t

he

requirements of your specific region.

Manufacturer’s approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

■ Approved parts or attachments are those either manufactured or provi

ded by

W

acker Neuson.

■ Approved modifications are those performed by an authorized Wack

er

Neuson ser

vice center according to written instructions published by Wacker

Neuson.

■ Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

■ Serious injury hazards to the operator and persons in the work area

■ Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

CALIFORNIA Proposition 65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws pertaining to spark arresters

AVISO: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

wc_tx004428en.fm

7

LTV

Abbreviations

Acronym Definition Acronym Definition

CARB California air resource board LTV Light tower vertical

CDL Commercial driver’s license NATM National association of trailer manufacturers

CO Carbon monoxide NHTSA National highway traffic safety administration

EPA Environmental protection agency PPE Personal protective equipment

GFCI Ground fault current interrupter S/N Serial number

LED Light-emitting diode VIN Vehicle identification number

wc_tx004428en.fm

8

LTV

This page is intentionally left blank.

Table of Contents

LTV

wc_bo5100030216_06TOC.fm

9

CALIFORNIA Proposition 65 Warning 3

Foreword 5

1 Safety Information 14

1.1 Signal Words Used in this Manual ................................................................14

1.2 Machine Description and Intended Use ........................................................15

1.3 Operating Safety ...........................................................................................16

1.4 Metal Halide Lamp Safety .............................................................................18

1.5 Service Safety ...............................................................................................18

1.6 Operator Safety while Using Internal Combustion Engines ..........................20

1.7 Safety Guidelines for Lifting the Machine .....................................................21

1.8 Safety Guidelines for Towing the Machine ...................................................21

1.9 Reporting Safety Defects ..............................................................................22

2 Labels 24

2.1 Label Locations .............................................................................................24

2.2 Label Meanings ............................................................................................26

3 Lifting and Transporting 34

3.1 Lifting the Machine ........................................................................................34

3.2 Preparing the Machine for Transport on a Truck or Trailer ...........................35

3.3 Before Towing Checklist ...............................................................................36

3.4 Towing the Machine ......................................................................................37

3.5 Trailer ............................................................................................................38

3.6 Flip-up Tongue ..............................................................................................39

4 Machine Setup 40

4.1 Preparing the Machine for First Use .............................................................40

4.2 Positioning the Machine ................................................................................41

4.3 Ground Connection .......................................................................................42

4.4 Leveling the Trailer—Vertical Mast Light Towers .........................................43

4.5 Refueling the Machine ..................................................................................44

4.6 Aiming the Lights—Vertical Mast Light Towers ............................................45

4.7 Manually Rotating the Light Bar ....................................................................47

4.8 Raising the Tower—Manual Winch System .................................................48

4.9 Lowering the Tower—Manual Winch System ...............................................50

Table of Contents LTV

wc_bo5100030216_06TOC.fm

10

4.10 Raising the Tower—Power Winch System ...................................................52

4.11 Lowering the Tower—Power Winch System ................................................54

5Operation 56

5.1 Generator Derating .......................................................................................56

5.2 Control Panels and Receptacles—KUBOTA ................................................56

5.3 Control Panels and Receptacles—KOHLER ................................................57

5.4 Control Panel and Receptacles—DeepSea ..................................................58

5.5 Machine Monitoring—DeepSea ....................................................................59

5.6 Alarms and Shut-Down Conditions—DeepSea ............................................61

5.7 Resetting the Maintenance Timers—DeepSea ............................................62

5.8 Before Starting ..............................................................................................63

5.9 Starting, Operating, Stopping the Machine—KUBOTA ................................64

5.10 Starting, Operating, and Stopping the Machine—KOHLER .........................66

5.11 Starting, Operating, Stopping the Machine—DeepSea ................................68

5.12 Auto Mode (Auto Start/Stop) .........................................................................70

5.13 Engine—Jump-Starting .................................................................................75

5.14 Emergency Shutdown Procedure .................................................................77

5.15 Using the Convenience Receptacles—50 Hz and 60 Hz .............................78

6 Factory-Installed Options 80

6.1 Cold Weather Package .................................................................................80

6.2 Engine Block Heater .....................................................................................80

6.3 Battery Blanket .............................................................................................81

6.4 Oil Pan Heater ..............................................................................................81

6.5 Fuel and Water Separator ............................................................................82

6.6 Positive Air Shutoff .......................................................................................82

6.7 Shore Power .................................................................................................82

6.8 Containment System Float Switch ................................................................83

6.9 LED Lights ....................................................................................................83

7 General Maintenance 84

7.1 Preparing for Maintenance ...........................................................................84

7.2 Periodic Maintenance Schedule ...................................................................84

7.3 Cleaning the Machine ...................................................................................85

7.4 Inspecting the Machine .................................................................................85

7.5 Maintaining the Trailer ..................................................................................86

7.6 Maintaining the Battery .................................................................................86

Table of Contents

LTV

wc_bo5100030216_06TOC.fm

11

7.7 Removing and Replacing Lamps ................................................................. 87

7.8 Checking and Draining the Containment System (if equipped) ................... 89

7.9 Long-Term Storage ...................................................................................... 90

7.10 Machine Disposal and Decommissioning .................................................... 91

8 Engine Maintenance: KUBOTA D1005 / D1105 92

9 Engine Maintenance: KUBOTA Z482 94

10 Engine Maintenance: KOHLER 1003 96

11 Troubleshooting 98

11.1 Kubota Error Codes ................................................................................... 100

12 Technical Data 101

12.1 Engine—KUBOTA ..................................................................................... 101

12.2 Engine—KOHLER ..................................................................................... 102

12.3 Generator ................................................................................................... 103

12.4 Machine ..................................................................................................... 104

12.5 Radiation Compliance ................................................................................ 105

12.6 Dimensions—LTV4K, LTV6K, LTV8K, LTV6L ........................................... 105

12.7 Dimensions—Skidded LTV6K, LTV8K, LTV6L .......................................... 105

13 Emissions Control Systems Information and Warranty: KUBOTA 106

13.1 Emission Control System Background Information .................................... 106

13.2 Limited Defect Warranty for Wacker Neuson Emission Control

Systems ..................................................................................................... 107

14 Emissions Control Systems Information and Warranty: KOHLER 110

14.1 Emission Control System Background Information .................................... 110

14.2 Limited Defect Warranty for Exhaust Emission Control System ................ 110

15 Schematics 111

15.1 LTV—Photo Sensor ................................................................................... 111

15.2 Components ............................................................................................... 111

15.3 LTV—Controller-Kubota Z482 ................................................................... 112

Table of Contents LTV

wc_bo5100030216_06TOC.fm

12

15.4 Components ............................................................................................... 113

15.5 LTV—Base Schematic ............................................................................... 114

15.6 Components ............................................................................................... 115

15.7 LTV—Metal Halide Lights Module ............................................................. 116

15.8 Components ............................................................................................... 116

15.9 LTV—120V / 30A Receptacle Module ....................................................... 117

15.10 Components ............................................................................................... 117

15.11 LTV—8 kW GFCI Receptacle Module ....................................................... 118

15.12 Components ............................................................................................... 118

15.13 LTV—Trailer ............................................................................................... 119

15.14 Components ............................................................................................... 119

15.15 LTV—Kubota Engine ................................................................................. 120

15.16 Components ............................................................................................... 121

15.17 LTV—Power Winch .................................................................................... 122

15.18 Components ............................................................................................... 122

15.19 LTV—LED Lights Module .......................................................................... 123

15.20 Components .............................................................................................. 123

15.21 LTV—Auto Start Module ............................................................................ 124

15.22 Components ............................................................................................... 124

15.23 LTV—Shore Power Module ....................................................................... 125

15.24 Components ............................................................................................... 125

15.25 LTV—Controller-Kubota D2005 / D1105 ................................................... 126

15.26 Components ............................................................................................... 127

15.27 LTV—230V / 50 HZ Module ....................................................................... 128

15.28 Components ............................................................................................... 128

15.29 LTV—Containment Switch ......................................................................... 129

15.30 Components ............................................................................................... 129

15.31 LTV—URI Telematics ................................................................................ 130

15.32 Components ............................................................................................... 130

16 Appendix I 131

16.1 Standard Racked Assembly ....................................................................... 131

16.2 Installing the Axle ....................................................................................... 132

16.3 Installing the Fenders ................................................................................. 133

16.4 Installing the Wheels .................................................................................. 134

16.5 Installing the Outriggers and Swivel Jacks ................................................ 135

16.6 Installing the Tongue Assembly ................................................................. 137

16.7 Installing the Mast ...................................................................................... 139

16.8 Installing the Standard Winch .................................................................... 140

16.9 Installing the Power Winch ......................................................................... 142

Table of Contents

LTV

wc_bo5100030216_06TOC.fm

13

16.10 Installing the Light Support Bracket and Light Bar 144

16.11 Installing the Lights—240W Metal Halide or 300W LED 145

16.12 Installing the Lights—240W LED 146

16.13 Connecting the Wiring at the Junction Box 147

wc_si000704en.fm

14

Safety Information LTV

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

► Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

► To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

► To avoid possible death or serious injury from this type of hazard, obey all

safety messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

► To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000704en.fm

15

LTV Safety Information

1.2 Machine Description and Intended Use

Machine

description

This machine is a mobile, trailer-mounted light tower. The Wacker Neuson Light

Tower consists of a trailer with a cabinet containing a diesel engine, a fuel tank, a

control panel, and an electric alternator. A telescoping tower with four metal halide

or LED lights is vertically mounted to the top of the cabinet. As the engine runs, the

generator converts mechanical energy into electric power. The metal halide or LED

lights run off this power. Receptacle(s) are also provided to power auxiliary loads.

The operator uses the control panel to operate and monitor the machine.

Intended use

This machine is intended for the illumination of outdoor areas. This machine is also

intended for the purpose of supplying electrical power to connected loads. Refer to

the machine specifications for the output voltage and frequency, and for the

maximum output power limit of this machine.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty. The following are some

examples of misuse:

■ Connecting a load that has voltage and frequency requirements that are

incompatible with the machine output

■ Overloading the machine with a device that draws excessive power during

either continuous running or start-up

■ Operating the machine in a manner that is inconsistent with all federal, state,

and local codes and regulations

■ Using the machine as a ladder, support, or work surface

■ Using the machine to carry or transport passengers or equipment

■ Using the machine to tow other machines (unless factory equipped)

■ Using the machine as a hoist, or hanging items from the tower

■ Operating the machine outside of factory specifications

■ Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

■ Heat, noise, exhaust, and carbon monoxide from the engine

■ Heat from the lights

■ Ultraviolet radiation from the lights

■ Fire hazards from improper refueling techniques

■ Fuel and its fumes

■ Electric shock and arc flash

■ Personal injury from improper lifting the trailer tongue

■ Glare from lights (lights may blind drivers of nearby motor vehicles if the lights

are incorrectly positioned)

wc_si000704en.fm

16

Safety Information LTV

■ Typical hazards related to towing a trailer on roads and highways

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

1.3 Operating Safety

Operator

training

Before operating the machine:

■ Read and understand the operating instructions contained in all manuals

delivered with the machine.

■ Familiarize yourself with the location and proper use of all controls and safety

devices.

■ Contact Wacker Neuson for additional training if necessary.

When operating this machine:

■ Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

■ Have received instruction on how to properly use the machine

■ Are familiar with required safety devices

The machine must not be accessed or operated by:

■ Children

■ People impaired by alcohol, drugs, or prescription drugs

Application

area

Be aware of the application area.

■ Keep unauthorized personnel, children, and pets away from the machine.

■ Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

■ Identify whether special hazards exist in the application area, such as toxic

gases or unstable ground conditions, and take appropriate action to eliminate

the special hazards before using the machine.

■ Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

■ All safety devices and guards are in place and in working order.

■ All controls operate correctly.

■ The machine is set up correctly according to the instructions in the Operator’s

Manual.

■ The machine is clean.

■ The machine’s labels are legible.

To ensure safe operation of the machine:

■ Do not operate the machine if any safety devices or guards are missing or

inoperative.

wc_si000704en.fm

17

LTV Safety Information

■ Do not modify or defeat the safety devices.

■ Only use accessories or attachments that are approved by Wacker Neuson.

Safe

operating

practices

When operating this machine:

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Do not operate a machine in need of repair.

■ Do not consume the operating fluids used in this machine. Depending on your

machine model, these operating fluids may include water, wetting agents, fuel

(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic oil,

heat transfer fluid (propylene glycol with additives), battery acid, or grease.

Personal

protective

equipment

(PPE)

Wear the following personal protective equipment (PPE) while operating this

machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

Before

starting

■ Be sure the machine is on a firm, level surface and will not tip, roll, slide, or fall

while operating.

■ Never connect the machine to other power sources, such as supply mains of

power companies.

■ Never use the machine if the insulation on the electrical cord is cut or worn

through.

■ Never raise the tower or operate the machine in high winds.

■ The tower extends up to 7 m (23 ft). Make sure the area above the trailer is

open and clear of overhead wires and obstructions.

Operation

■ Keep the area under and around the lights clear of people while raising and

lowering the tower.

■ Do not move the machine while it is operating or while the tower is raised.

After use

■ Stop the engine when the machine is not being operated.

■ Close the fuel valve on engines equipped with one when the machine is not

being operated.

■ Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

■ Store the machine properly when it is not being used. The machine should be

stored in a clean location out of the reach of children.

■ Lower the tower when not in use, or if high winds or electrical storms are

expected in the area.

■ The lamps become extremely hot during use! Allow the lamp and fixture to cool

10–15 minutes before handling.

wc_si000704en.fm

18

Safety Information LTV

1.4 Metal Halide Lamp Safety

Description

The lamps provided with the machine are electric discharge lamps. They are

designed for use with metal halide ballasts only, and require time to reach full

brightness on initial startup and after a power interruption. These lamps comply

with FDA regulation performance standards 21 CFR 1040-30.

Operating

safety

Replace damaged lamps according to the instructions in section Removing and

Replacing Lamps.

1.5 Service Safety

Service

training

Before servicing or maintaining the machine:

■ Read and understand the instructions contained in all manuals delivered with

the machine.

■ Familiarize yourself with the location and proper use of all controls and

protective devices.

■ Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

■ Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

■ Do not allow untrained or improperly trained people to service or maintain the

machine. Personnel servicing or maintaining the machine must be familiar with

the associated potential risks and hazards.

Precautions

When servicing or maintaining the machine:

■ Read and understand the service procedures before performing any service to

the machine.

■ All adjustments and repairs must be completed before operating the machine.

Do not operate the machine with a known problem or deficiency.

■ All repairs and adjustments shall be completed by a qualified technician.

■ Turn off the machine before performing maintenance or making repairs.

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Reinstall the safety devices and guards after repair and maintenance

procedures are complete.

■ Before servicing the machine, make sure the engine start switch is turned to the

OFF position, the circuit breakers are open (off), and the negative terminal on

battery is disconnected. Do not perform even routine service (oil/filter changes,

cleaning, etc.) unless all electrical components are shut down.

WARNING

Personal injury hazard. Broken or punctured lamps can cause serious skin burns

and eye inflammation from shortwave ultraviolet radiation.

► Do not operate the machine if a lamp is damaged.

► Replace damaged lamps immediately.

wc_si000704en.fm

19

LTV Safety Information

■ Always turn off light circuit breakers and shut down engine before disconnecting

light fixtures or changing light bulbs.

Machine

modifications

When servicing or maintaining the machine:

■ Use only accessories/attachments that are approved by Wacker Neuson.

■ Do not defeat safety devices.

■ Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

■ Replace worn or damaged components.

■ Replace all missing and hard-to-read labels.

■ When replacing electrical components, use components that are identical in

rating and performance to the original components.

■ When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

Cleaning

When cleaning and servicing the machine:

■ Keep machine clean and free of debris such as leaves, paper, cartons, etc.

■ Keep labels legible.

■ Do not clean the machine while it is running.

■ Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

Personal

protective

equipment

(PPE)

Wear the following personal protective equipment (PPE) while servicing or

maintaining this machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

In addition, before servicing or maintaining the machine:

■ Tie back long hair.

■ Remove all jewelry (including rings).

wc_si000704en.fm

20

Safety Information LTV

1.6 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

■ Keep the area around the exhaust pipe free of flammable materials.

■ Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

■ Do not smoke while operating the machine.

■ Do not run the engine near sparks or open flames.

■ Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

■ Do not operate a machine when its fuel cap is loose or missing.

■ Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

■ Do not use the machine in areas with risk of explosion or fire.

Refueling

safety

When refueling the engine:

■ Clean up any spilled fuel immediately.

■ Refill the fuel tank in a well-ventilated area.

■ Reinstall the fuel tank cap after refueling.

■ Use tools specifically meant for refueling (for example, a fuel hose or funnel).

■ Do not smoke.

■ Do not refuel a hot or running engine.

■ Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

► Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

► NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through items such as exhaust fans or hoses.

La page charge ...

Wacker Neuson LTV6L Manuel utilisateur

Ce manuel convient également à

Wacker Neuson LTV6L Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents