Dolmar AS-3625 Le manuel du propriétaire

GB

Cordless Chain Saw Instruction Manual

F

Tronçonneuse sans Fil Manuel d’instructions

D

Akku-Kettensäge Betriebsanleitung

I

Motosega a batteria Istruzioni per l’uso

NL

Accu-kettingzaag Gebruiksaanwijzing

E

Electrosierra Inalámbrica Manual de instrucciones

P

Motosserra a Bateria Manual de instruções

DK

Akku-kædesav Brugsanvisning

GR Αλυσπρίν µπαταρίας δηγίες ρήσεως

AS-3625

AS-3626

2

PARTS DESCRIPTION / DESCRIPTION DES PIÈCES / BESCHREIBUNG DER TEILE /

DESCRIZIONE DELLE PARTI / BESCHRIJVING VAN ONDERDELEN / DESCRIPCIÓN DE LAS PARTES /

DESCRIÇÃO DAS PEÇAS / BESKRIVELSE AF DELE / ΠΕΡΙΓΡΑΦΗ ΤΩΝ ΕΑΡΤΗΜΑΤΩΝ

ENGLISH FRANÇAIS

1

3

4

5

9

2

6

8

7

13

12

11

14

10

1Lever

2 Front hand guard

3 Top handle

4 Battery cartridge

5 Carabiner or rope attachment point

6 Guide bar

7Saw chain

8 Sprocket cover

9Chain cover

10 Lock off button

11 Switch trigger

12 Front handle

13 Serrated rail (claw stop)

14 Battery cover

1Levier

2 Protège-main avant

3 Poignée supérieure

4 Batterie

5 Point de fixation du mousqueton ou de la corde

6 Guide de chaîne

7 Chaîne

8 Couvre-pignon

9 Cache de chaîne

10 Bouton de sécurité

11 Gâchette

12 Poignée avant

13 Rail dentelé (butée à griffe)

14 Couvercle de batterie

3

DEUTSCH

ITALIANO

NEDERLANDS

ESPAÑOL

1 Hebel

2 Vorderer Handschutz

3Obergriff

4 Akku

5 Befestigungsöse für Karabinerhaken oder Seil

6Schwert

7 Sägekette

8 Kettenraddeckel

9 Kettenabdeckung

10 Einschaltarretierung

11 Schalter

12 Frontgriff

13 Krallenanschlag (Klauenanschlag)

14 Akkuabdeckung

1Leva

2 Protezione mano anteriore

3 Manico superiore

4 Cartuccia batteria

5 Gancio o punto di attacco fune

6 Barra guida

7 Catena sega

8 Coperchio rocchetto

9 Coperchio catena

10 Bottone di sblocco

11 Interruttore a grilletto

12 Manico anteriore

13 Guida dentata (fermo dente)

14 Coperchio batteria

1 Hendel

2 Beschermkap van voorhandgreep

3 Bovenhandgreep

4 Accu

5 Bevestigingsoog voor karabijnhaak of touw

6 Zaagblad

7 Zaagketting

8 Afdekking van kettingwiel

9 Kettingdeksel

10 Ontgrendelknop

11 Trekschakelaar

12 Voorhandgreep

13 Getande kam (klauwaanslag)

14 Deksel van de accu

1Baja

2 Protector de la mano delantera

3 Empuñadura principal

4 Cartucho de batería

5 Punto de sujeción de mosquetón o cuerda

6 Placa de guía

7 Cadena de sierra

8 Cubierta del piñón

9 Cubierta de la cadena

10 Botón de seguro

11 Gatillo interruptor

12 Empuñadura delantera

13 Riel dentado (tope de gancho)

14 Tapa de la batería

4

PORTUGUÊS

DANSK

ΕΛΛΗΝΙΚΑ

1 Alavanca

2 Protector frontal das mãos

3 Pega superior

4 Bateria

5 Ponto de fixação da corda ou gancho

6 Espada

7 Corrente da electroserra

8 Cobertura da roda dentada

9 Cobertura da corrente

10 Botão de bloqueio

11 Gatilho do interruptor

12 Pega frontal

13 Trilho dentado (retentor de garras)

14 Tampa da bateria

1Arm

2 Frontkappe

3 Tophåndtag

4 Akku

5 Fastgørelsespunkt til karabinhage eller reb

6Sværd

7 Savkæde

8 Kædehjulsdæksel

9 Kædedæksel

10 Låseknap

11 Afbryderknap

12 Fronthåndtag

13 Takket kant (hage-stop)

14 Batteridæksel

1 Μλς

2 Μπρστινς πρφυλακτήρας εριών

3 Άνω λαή

4 Κασετίνα µπαταρίας

5 Carabiner ή σηµεί πρσδεσης σινιύ

6 Κατευθυντήρια λάµα

7 Αλυσίδα πρινιύ

8 Κάλυµµα δντωτύ τρύ

9 Κάλυµµα αλυσίδας

10 Πλήκτρ ασφάλειας

11 Σκανδάλη διακπτης

12 Μπρστινή λαή

13 δντωτή ράγα (στπ σιαγνας)

14 Κάλυµµα µπαταρίας

5

12

34

56

78

13

14

11

12

10

4

5

9

78

6

1

2

3

15

16

17

18

13

14

11

12

10

4

5

9

78

6

1

2

3

15

16

17

18

6

910

11 12

13 14

15 16

20

22

15

16

15

22

27

26

18

24

25

2 - 4 mm

23

21

19

15

16

7

17 18

19 20

21 22

23 24

29

31

1

2

40

3

2

29

28

30

2

28

37

36

39

38

32

33

34

35

8

25 26

27 28

29 30

31 32

45

o

2

1

/2

45

o

41

A

B

A

B

9

33 34

35 36

37 38

39 40

48

49

45

3

46

47

42

43

44

10

41 42

43 44

45

52

53

51

50

19

50

11

END005-4

Symbols

The followings show the symbols used for the equipment. Be sure that you understand their meaning before use.

Symboles

Nous donnons ci-dessous les symboles utilisés pour l’outil. Assurez-vous que vous en avez bien compris la significa-

tion avant d’utiliser l’outil.

Symbole

Die folgenden Symbole werden für die Maschine verwendet. Machen Sie sich vor der Benutzung unbedingt mit ihrer

Bedeutung vertraut.

Simboli

Per questo utensile vengono usati i simboli seguenti. Bisogna capire il loro significato prima di usare l’utensile.

Symbolen

Voor dit gereedschap worden de volgende symbolen gebruikt. Zorg ervoor dat u de betekenis van deze symbolen

begrijpt alvorens het gereedschap te gebruiken.

Símbolos

A continuación se muestran los símbolos utilizados con esta herramienta. Asegúrese de que entiende su significado

antes de usarla.

Símbolos

O seguinte mostra os símbolos utilizados para a ferramenta. Certifique-se de que compreende o seu significado antes

da utilização.

Symboler

Nedenstående symboler er anvendt i forbindelse med denne maskine. Vær sikker på, at De har forstået symbolernes

betydning, før maskinen anvendes.

Σύµλα

Τα ακλυθα δείνυν τα σύµλα πυ ρησιµπιύνται για τ µηάνηµα. Βεαιωθείτε τι καταλααίνετε

τη σηµασία τυς πριν απ τη ρήση.

• Read instruction manual.

• Lire le mode d’emploi.

• Bitte Bedienungsanleitung lesen.

• Leggete il manuale di istruzioni.

• Lees de gebruiksaanwijzing.

• Lea el manual de instrucciones.

• Leia o manual de instruções.

• Læs brugsanvisningen.

• ∆ιαάστε τις δηγίες ρήσης.

• Wear eye protection.

• Portez une protection pour les yeux.

• Eine Schutzbrille tragen.

• Indossare gli occhiali di protezione.

• Draag oogbescherming.

• Póngase protección para los ojos.

• Utilize protectores para os olhos.

• Brug øjenbeskyttelse.

• Να φράτε πρστατευτικά µατιών.

12

• Wear ear protection.

• Portez une protection pour les oreilles.

• Einen Gehörschutz tragen.

• Indossare la protezione delle orecchie.

• Draag gehoorbescherming.

• Póngase protección para los oídos.

• Utilize protectores para os ouvidos.

• Brug høreværn.

• Να φράτε πρστατευτικά αυτιών.

• Wear a helmet, goggles and ear protection.

• Portez un casque, des lunettes de sécurité et une protection pour les oreilles.

• Tragen Sie einen Helm, eine Schutzbrille und einen Gehörschutz.

• Indossare il casco, gli occhiali di protezione e i paraorecchi.

• Draag een veiligheidshelm, veiligheidsbril en oorbescherming.

• Póngase casco, gafas de seguridad y protección para los oídos.

• Use um capacete, óculos de segurança e protectores para os ouvidos.

• Bær hjelm, sikkerhedsbriller og høreværn.

• Να φράτε κράνς και µέσα πρστασίας ρασης και ακής.

• Do not expose to rain.

• N’exposez pas l’outil à la pluie.

• Die Maschine keinem Regen aussetzen.

• Non esporre alla pioggia.

• Stel het gereedschap niet bloot aan regen.

• No exponga a la lluvia.

• Não exponha a ferramenta à chuva.

• Udsæt ikke saven for regn.

• Να µην εκτίθεται στη ρη.

13

• Hold the saw with both hands while working! One-handed use is extremely hazardous!

• Tenez la scie fermement à deux mains pendant que vous travaillez ! L’utilisation avec une

seule main est extrêmement dangereuse !

• Die Säge während der Arbeit mit beiden Händen halten! Einhändiger Betrieb ist äußerst

gefährlich!

• Tenere la sega con entrambe le mani durante il lavoro! L’uso con una sola mano è estrema-

mente pericoloso!

• Houd de kettingzaag tijdens het werk met beide handen vast! Gebruik met slechts één hand

is uitermate gevaarlijk.

• ¡Sujete la sierra con ambas manos mientras realiza el trabajo! ¡La utilización una sola mano

es muy peligroso!

• Segure a electroserra com as duas mãos ao trabalhar. É muito perigoso segurá-la só com

uma mão.

• Hold i saven med begge hænder under arbejdet! Anvendelse med kun den ene hånd på

saven er yderst farligt!

• Να κρατάτε τ αλυσπρίν µε τα δύ έρια στη διάρκεια της εργασίας! Η ρήση µε τ

ένα έρι είναι εαιρετικά επικίνδυνη!

• Maximum permissible cut length

• Longueur de coupe maximale admise

• Höchstzulässige Schnittlänge

• Lunghezza di taglio massima permissibile

• Maximaal toegestane zaaglengte

• Longitud de corte permitida máxima

• Comprimento máximo de corte permitido

• Maks. tilladt skærelængde

• Μέγιστ επιτρεπµεν µήκς κπής

• Direction of chain travel

• Sens de progression de la chaîne

• Kettenumlaufrichtung

• Direzione di corsa catena

• Draairichting van de ketting

• Dirección de desplazamiento de la cadena

• Sentido de movimento da corrente

• Retning af kædens bevægelse

• Κατεύθυνση διαδρµής αλυσίδας

14

• Saw chain oil adjustment

• Réglage d’huile de la chaîne

• Sägekettenöleinstellung

• Regolazione olio catena sega

• Afstelling voor zaagkettingolie

• Ajuste del aceite de la cadena de sierra

• Regulação da lubrificação da corrente da electroserra

• Justering af savkædeolie

• Ρύθµιση λίπανσης αλυσίδας αλυσπρίνυ

• Only for EU countries

Do not dispose of electric equipment or battery pack together with household waste material!

In observance of European Directive 2002/96/EC on waste electric and electronic equipment, 2006/

66/EC on batteries and accumulators and waste batteries and accumulators and their implementa-

tion in accordance with national laws, electric equipment and battery pack that have reached the

end of their life must be collected separately and returned to an environmentally compatible recy-

cling facility.

• Uniquement pour les pays de l’UE

Ne pas jeter les appareils électriques et les batteries avec les ordures ménagères !

Conformément aux directives européennes 2002/96/CE (relative aux déchets d’équipements élec-

triques et électroniques) et 2006/66/CE (relative aux piles et accumulateurs ainsi qu’aux déchets de

piles et accumulateurs), ainsi qu’à leur application en conformité avec les lois nationales, les appar-

eils électriques et batteries qui ont atteint la fin de leur durée de service doivent être collectés

séparément et renvoyés à un établissement de recyclage respectueux de l’environnement.

• Nur für EG-Länder

Werfen Sie Elektrogeräte oder Akkus nicht in den Hausmüll!

Gemäß der Europäischen Richtlinie 2002/96/EG über Elektro- und Elektronik-Altgeräte, 2006/66/

EG über Batterien, Akkus sowie verbrauchte Batterien und Akkus und ihre Umsetzung gemäß den

Landesgesetzen müssen Elektrogeräte und Akkus, die das Ende ihrer Lebensdauer erreicht haben,

getrennt gesammelt und einer umweltgerechten Recycling-Einrichtung zugeführt werden.

• Soltanto per i Paesi dell'unione europea

Questo apparecchio elettrico o la batteria non devono essere gettati via con i rifiuti domestici.

In osservanza alla Direttiva Europea 2002/96/CE sugli apparecchi elettrici ed elettronici di scarto,

2006/66/CE sulle batterie e gli accumulatori, e sulle batterie e gli accumulatori esausti, e la sua

implementazione secondo le leggi locali, gli apparecchi elettrici e le batterie che hanno raggiunto la

fine della loro vita di servizio devono essere raccolti separatamente e portati in un centro di smalti-

mento ecocompatibile.

• Alleen voor EU-landen

Geef elektrisch gereedschap of accu's niet met het huisvuil mee!

Volgens de Europese richtlijn 2002/96/EC inzake oude elektrische en elektronische apparaten, rich-

tlijn 2006/66/EC inzake batterijen en accu's en wegwerpbatterijen, en de toepassing daarvan bin-

nen de nationale wetgeving, dienen gebruikte elektrisch apparaten en accu's die het einde van hun

levensduur hebben bereikt, gescheiden te worden ingezameld en te worden afgevoerd naar een

recyclebedrijf dat voldoet aan de geldende milieu-eisen.

• Sólo para países de la Unión Europea

¡No tire aparatos eléctricos ni baterías a la basura con los residuos domésticos!

En conformidad con la Directiva Europea 2002/96/EC sobre residuos de aparatos eléctricos y elec-

trónicos y la Directiva Europea 2006/66/EC sobre baterías y acumuladores y residuos de baterías y

de acumuladores y su aplicación de acuerdo con la legislación nacional, los aparatos eléctricos y

las baterías cuya vida útil haya llegado a su fin se deberán recoger por separado y trasladar a una

planta de reciclaje que cumpla con las exigencias ecológicas.

Cd

Ni-MH

Li-ion

15

• Apenas para os países da União Européia

Não deite equipamentos eléctricos nem baterias no lixo doméstico!

De acordo com as directivas europeias 2002/96/CE sobre ferramentas eléctricas e electrónicas

usadas e 2006/66/CE sobre baterias e acumuladores e respectivos resíduos e a implementação

dessas directivas conforme a lei nacional, as ferramentas eléctricas e as baterias que atingem o fim

de sua vida útil devem ser recolhidas em separado e encaminhadas a uma instalação de recicla-

gem compatível com os regulamentos sobre o meio ambiente.

• Gælder kun lande i EU

Undlad at bortskaffe elektrisk udstyr eller akkuer sammen med almindeligt husholdningsaffald.

I henhold til EU-direktiv 2002/96/EC angående brugt elektrisk og elektronisk udstyr, 2006/66/EC

angående batterier og akkumulatorer og brugte batterier og iværksættelse af bortskaffelse af bat-

terier og akkumulatorer i overensstemmelse med nationale love, skal elektrisk udstyr og akkuer, der

har nået slutningen af deres levetid, indsamles separat og afhændes til en genbrugsfacilitet, som er

miljømæssigt kompatibel.

• Μν για ώρες ΕΕ

Μην απρρίπτετε ηλεκτρικ επλισµ ή µπαταρίες µαί µε τα ικιακά απλητα!

Σύµφωνα µε την Ευρωπαϊκή δηγία 2002/96/ΕΚ περί απλήτων ειδών ηλεκτρικύ και

ηλεκτρνικύ επλισµύ και την δηγία 2006/66/EΚ περί µπαταριών και συσσωρευτών και

απλήτων µπαταριών και συσσωρευτών και την εφαρµγή τυς σύµφωνα µε την εθνική

νµθεσία, απαιτείται συλλγή τυ ηλεκτρικύ επλισµύ και των µπαταριών, τ ρι

ωής των πίων έει λήει, εωριστά και επιστρφή τυς σε εγκατάσταση ανακύκλωσης

συµατή µε την πρστασία τυ περιάλλντς.

16

ENGLISH (Original instructions)

Explanation of general view

1Red part

2Button

3 Battery cartridge

4 Lock-off button

5 Switch trigger

6 Front hand guard

7Lock

8 Unlock

9 Adjusting screw

10 Carabiner

(rope attachment point)

11 Indicator lamps

12 CHECK button

13 Slightly slide

14 Move in the upright position

15 Press in

16 Loosen

17 Sprocket cover

18 Adjusting dial

19 Sprocket

20 Adjusting pin

21 Small hole

22 Tighten

23 Lever

24 Low

25 High

26 Guide bar

27 Saw chain

28 Adapter

29 Hook

30 Tool

31 Belt

32 Arm cord hook band

33 Holder

34 Extension cord (Battery

adapter)

35 Adapter (Battery adapter)

36 Oil tank cap

37 Oil tank opening

38 Oil inspection window

(for refilling the tank with oil)

39 Oil inspection window

40 Lower guide

41 Felling area

42 Felling direction

43 Danger zone

44 Escape route

45 Scabbard (chain cover)

46 File forward stroke

47 1/5 of the file diameter

48 Small dust or particles

49 Slotted bit screwdriver

50 Locking ring

51 Limit mark

52 Brush holder cap

53 Screwdriver

SPECIFICATIONS

• Weight, with battery cartridge, according to EPTA-Pro-

cedure 01/2003

ENE031-1

Intended use

The tool is intended for cutting lumbers and logs.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future reference.

GEB071-5

CORDLESS CHAIN SAW SAFETY WARNINGS:

1. Keep all parts of the body away from the saw

chain when the chain saw is operating. Before

you start the chain saw, make sure the saw chain

is not contacting anything. A moment of inatten-

tion while operating chain saws may cause entan-

glement of your clothing or body with the saw chain.

2. Always hold the chain saw with your right hand

on the rear handle and your left hand on the

front handle. Holding the chain saw with a reversed

hand configuration increases the risk of personal

injury and should never be done.

3. Hold the power tool by insulated gripping sur-

faces only, because the saw chain may contact

hidden wiring. Saw chains contacting a “live” wire

may make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

Model AS-3625 AS-3626

Chain speed per minute 8.3 m/s (500 m/min) 8.3 m/s (500 m/min)

Length of guide bar 250 mm 250 mm

Guide bar type

Sprocket nose

bar

Carving bar

Sprocket nose

bar

Carving bar

Saw chain

Type 91VG 25AP 91VG 25AP

Pitch 3/8”1/4”3/8”1/4”

No. of drive links 40 60 40 60

Number of teeth 6 9 6 9

Overall length 576 mm 589 mm 577 mm 590 mm

Net weight 4.5 kg 4.5 kg

Rated voltage D.C. 36 V D.C. 36 V

17

4. Wear safety glasses and hearing protection. Fur-

ther protective equipment for head, hands, legs

and feet is recommended. Adequate protective

clothing will reduce personal injury by flying debris

or accidental contact with the saw chain.

5. Before starting work, check that the chain saw is in

proper working order and that its condition complies

with the safety regulations. Check in particular that:

• The chain brake is working properly;

• The run-down brake is working properly;

• The bar and the sprocket cover are fitted cor-

rectly;

• The chain has been sharpened and tensioned in

accordance with the regulations;

6. Do not operate a chain saw in a tree. Operation of

a chain saw while up in a tree may result in personal

injury.

7. Always keep proper footing and operate the

chain saw only when standing on fixed, secure

and level surface. Slippery or unstable surfaces

such as ladders may cause a loss of balance or con-

trol of the chain saw.

8. When cutting a limb that is under tension be

alert for spring back. When the tension in the wood

fibres is released the spring loaded limb may strike

the operator and/or throw the chain saw out of con-

trol.

9. Use extreme caution when cutting brush and

saplings. The slender material may catch the saw

chain and be whipped toward you or pull you off bal-

ance.

10. Carry the chain saw by the front handle with the

chain saw switched off and away from your body.

When transporting or storing the chain saw

always fit the guide bar cover. Proper handling of

the chain saw will reduce the likelihood of accidental

contact with the moving saw chain.

11. Follow instructions for lubricating, chain ten-

sioning and changing accessories. Improperly

tensioned or lubricated chain may either break or

increase the chance for kickback.

12. Keep handles dry, clean, and free from oil and

grease. Greasy, oily handles are slippery causing

loss of control.

13. Cut wood only. Do not use chain saw for pur-

poses not intended. For example: do not use

chain saw for cutting plastic, masonry or non-

wood building materials. Use of the chain saw for

operations different than intended could result in a

hazardous situation.

14. Causes and operator prevention of kickback:

Kickback may occur when the nose or tip of the

guide bar touches an object, or when the wood

closes in and pinches the saw chain in the cut.

Tip contact in some cases may cause a sudden

reverse reaction, kicking the guide bar up and back

towards the operator.

Pinching the saw chain along the top of the guide

bar may push the guide bar rapidly back towards the

operator.

Either of these reactions may cause you to lose con-

trol of the saw which could result in serious personal

injury. Do not rely exclusively upon the safety

devices built into your saw. As a chain saw user, you

should take several steps to keep your cutting jobs

free from accident or injury.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be

avoided by taking proper precautions as given

below:

- Maintain a firm grip, with thumbs and fingers

encircling the chain saw handles, with both hands

on the saw and position your body and arm to

allow you to resist kickback forces. Kickback

forces can be controlled by the operator, if proper

precautions are taken. Do not let go of the chain

saw.

- Do not overreach and do not cut above shoul-

der height. This helps prevent unintended tip

contact and enables better control of the chain

saw in unexpected situations.

- Only use replacement bars and chains speci-

fied by the manufacturer. Incorrect replacement

bars and chains may cause chain breakage and/

or kickback.

- Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increased kickback.

15. Do not start the chain saw with the chain cover

being installed on it. Starting the chain saw with

the chain cover being installed on it may cause the

chain cover to thrown out forward resulting in per-

sonal injury and damage to objects around the oper-

ator.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this instruc-

tion manual may cause serious personal injury.

18

ENC007-6

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it

is severely damaged or is completely worn out.

The battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use dropped or struck battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the bat-

tery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-

tery cartridge cool down before charging it.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before adjusting or checking

function on the tool.

Installing or removing battery cartridge (Fig. 1)

CAUTION:

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury.

• Always switch off the tool before installing or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while sliding the button on the front of the cartridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Switch action (Fig. 2)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button and pull the

switch trigger. Release the switch trigger to stop.

Checking the chain brake (Fig. 3)

NOTE:

• If the chain saw fails to start, the chain brake must be

released. Pull the front hand guard backwards firmly

until you feel it engage.

Hold the chain saw with both hands when switching it on.

Hold the top handle with your right hand, the front handle

with your left. The bar and the chain must not be in con-

tact with any object.

First press the lock-off button, then the switch trigger.

The saw chain starts immediately.

Press the front hand guard forwards using the back of

your hand. The saw chain must come to an immediate

standstill.

CAUTION:

• Should the saw chain not stop immediately when this

test is performed, the saw may not be used under any

circumstances. Consult a DOLMAR specialist repair

shop.

19

Checking the run-down brake

Switch on the chain saw.

Release the switch trigger completely. The saw chain

must come to a standstill within one second.

CAUTION:

• Should the saw chain not come to a stop within one

second when this test is performed, the saw must not

be used. Consult a DOLMAR specialist repair shop.

Adjusting the chain lubrication (Fig. 4)

You can adjust the oil pump feed rate with the adjusting

screw. The amount of oil can be adjusted using the uni-

versal wrench.

Carabiner (rope attachment point) (Fig. 5)

Carabiner (Rope attachment point) is for use of tool

hanging. Before using carabiner, pull it out and tie it with

a rope.

Battery protection system

The tool is equipped with the protection system, which

automatically cuts off the output power for its long service

life.

The tool may stop during operation when the tool and/or

battery are placed under the following situation. This is

caused by the activation of protection system and does

not show the tool trouble.

• When the tool is overloaded:

At this time, release the switch trigger and remove

causes of overload and then pull the switch trigger

again to restart. When the tool does not work even

after pulling the switch trigger, the battery power

auto-stop is still at work. Charge the battery car-

tridge before use.

• When the remaining battery capacity becomes low:

Recharge the battery cartridge.

Battery remaining capacity indicator (only for

models with Battery AP-3622)

Battery AP-3622 is equipped with the battery remaining

capacity indicator. (Fig. 6)

Press the CHECK button to indicate the battery remain-

ing capacity. The indicator lamps will then light for

approx. three seconds.

• When only the lowermost indicator lamp (next to the

“E”) blinks, or when none of the indicator lamps light,

the battery charge has run out, so the tool does not

operate. In these cases, charge the battery or replace

the empty battery with a fully charged one.

• When two or more indicator lamps do not light even

after charging is complete, the battery has reached the

end of its service life.

• When the upper two and lower two indicator lamps light

alternately, the battery may have malfunctioned. Con-

tact your local DOLMAR authorized service center.

NOTE:

• The indicated charge may be lower than the actual

level during use or immediately after using the tool.

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing saw chain

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before installing or removing

the saw chain.

• Always wear gloves when installing or removing the

saw chain.

1. To remove the saw chain, slightly slide the lever in

the direction of arrow so that it can be released from

the locked position and move the lever in the upright

position as shown in the figure. (Fig. 7)

2. Press the lever and with the lever pressed in, turn it

counterclockwise to loosen the nut until sprocket

cover comes off. (Pressing in the lever leads to the

fitting of lever into the nut.) (Fig. 8)

3. Turn the adjusting dial counterclockwise to release

the saw chain tension.

4. Remove the sprocket cover.

5. Remove the saw chain and guide bar from the chain

saw.

6. To install the saw chain, fit in one end of the saw

chain on the top of the guide bar and the other end

of it around the sprocket. (Fig. 9)

At this time, fit the saw chain as shown in the figure

because it rotates in the direction of arrow.

7. Rest the guide bar in place on the chain saw.

8. Turn the adjusting dial counterclockwise to slide the

adjusting pin in the direction of arrow. (Fig. 10)

9. Place the sprocket cover on the chain saw so that

the adjusting pin is positioned in a small hole in the

guide bar. (Fig. 11)

10. Press in the lever and with the lever depressed turn

it fully clockwise to tighten the nut. Then make it

about a quarter turn counterclockwise to loosen the

nut lightly. (Fig. 12)

Indicator lamps

Remaining capacity

70% to 100%

45% to 70%

20% to 45%

0% to 20%

Charge the battery.

The battery may have

malfunctioned.

Lighted

Off

Blinking

E

F

20

Adjusting saw chain tension

The saw chain may become loose after many hours of

use. From time to time check the saw chain tension

before use. (Fig. 13)

Move the lever in the upright position.

Press in the lever. With the lever depressed, make a

quarter turn on it counterclockwise to loosen the nut

lightly. (Pressing in the lever leads to the fitting of lever

into the nut.) (Fig. 14)

Turn the adjusting dial to adjust saw chain tension. Grasp

the saw chain in the middle of the guide bar and lift up.

The gap between the guide bar and the tie strap of the

saw chain should be approx. 2 – 4 mm. If the gap is not

approx. 2 – 4 mm, slightly turn the adjusting dial which

secures the guide bar. At this time, adjust with the tip of

guide bar slightly pointing up. (Fig. 15)

With the lever depressed, turn it fully clockwise to tighten

the nut firmly. (Fig. 16)

Return the lever to its original position. (Fig. 17)

CAUTION:

• Excessively high tension of saw chain may cause

breakage of saw chain, wear of the guide bar and

breakage of the adjusting dial.

• Installing or removing saw chain should be carried out

in a clean place free from sawdust and the like.

Battery adapter (Accessory) (Fig. 18 & 19)

CAUTION:

• Before using battery adapter, read all instructions on

tools using battery.

• When charging a battery cartridge, first remove it from

the battery adapter and then charge it. It is not allowed

to charge the battery cartridge while using battery

adapter.

Installing or removing battery adapter

• Always switch off the tool before insertion or removal of

the battery adapter.

• To remove the battery adapter, withdraw it from the tool

while sliding the button on the adapter.

• To insert the battery adapter, align the tongue on the

battery adapter with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not use force when inserting the battery adapter. If

the adapter does not slide in easily, it is not being

inserted correctly.

• The way of removing or installing a battery cartridge

from or on the battery adapter is the same as that of

removing or installing it from or on the tools.

• Press down the hook securely as far as it will go when

the battery adapter is hooked on the waist belt and sim-

ilar objects.

Arm cord hook (Accessory) (Fig. 20)

CAUTION:

• Do not attach the holder of arm cord hook to other than

the extension cord. Failure to do so may cause an acci-

dent or personal injury.

Using the arm cord hook helps to minimize a risk of cut-

ting off the extension cord unexpectedly caused by the

loose extension cord.

Attach firmly the arm cord hook band placing around

your arm and pass the extension cord through the holder.

The length of the arm cord hook band is adjustable.

NOTE:

• Do not pass the extension cord through the band.

• Do not force the opening of the holder. Failure to do so

may cause deflection and damage to it.

OPERATION

Lubrication (Fig. 21)

Saw chain is automatically lubricated when the tool is in

operation.

Check the amount of remaining oil in the oil tank through

the oil inspection window.

To refill the tank, remove the cap from the oil tank open-

ing. The oil tank capacity is 85 ml.

After refilling the tank, always screw the provided oil tank

cap on the chain saw.

CAUTION:

• When filling the chain saw with chain oil for the first

time, or refilling the tank after it has been completely

emptied, add oil up to the bottom edge of the filler neck.

The oil delivery may otherwise be impaired.

• As a saw chain oil, use oil exclusively for Dolmar chain

saws or oil available in market.

• Never use oil including dust and particles or volatile oil.

• When pruning trees, use botanical oil. Mineral oil may

harm trees.

• Never force the chain saw when pruning trees.

• Before cutting out, make sure that the provided oil tank

cap is screwed in place.

Hold the chain saw away from the tree. Start it and wait

until lubrication on saw chain is adequate.

Bring the lower guide into contact with the branch to be

cut before switching on. Cutting without bringing the

lower guide into contact with the branch may cause the

guide bar to wobble, resulting in injury to operator.

Saw the wood to be cut by just moving it down. (Fig. 22)

La page charge ...

Dolmar AS-3625 Le manuel du propriétaire

Ce manuel convient également à

Dolmar AS-3625 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents