ACDelco ARM317-4A Product Information Manual

ARM 3V SERIES

DIGITAL ANGLE TORQUE WRENCH

PRODUCT INFORMATION MANUAL

Manuel informations du produit

Manual información del producto

English

Français

Español

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY,

OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT.

CE MANUEL CONTIENT DES INFORMATIONS IMPORTANTE CONCERNANT LA

SECURITE, L'OPERATION, LA MAINTENANCE ET LE STOCKAGE DE CE

PRODUIT.

ESTE MANUAL CONTIENE INFORMACIÓN IMPORTANTE ACERCA DE LA

SEGURIDAD, FUNCIONAMIENTO, MANTENIMIENTO Y ALMACENAMIENTO DE

ESTE PRODUCTO.

DO NOT ATTEMPT TO OPERATE THE TOOL UNTIL YOU HAVE READ AND UNDERSTOOD ALL

INSTRUCTIONS AND SAFETY RULES CONTAINED IN THIS MANUAL. FAILURE TO COMPLY

MAY RESULT IN ACCIDE

NTS INVOLVING FIRE, ELECTRIC SHOCK, OR SERIOUS PERSONAL

INJURY. SAVE THIS OWNER’S MANUAL FOR FUTURE REFERENCE AND REVIEW IT

FREQUENTLY FOR SAFE OPERATION.

NE PAS TENTER D'OPERER L'OUTIL TANT QUE VOUS N'AVEZ PAS LU ET COMPRIS TOUTES

LES INSTRUCTIONS ET REGLES DE SECURITE CONTENUES DANS CE MANUEL. SINON VOUS

RISQUEZ DES ACCIDENTS TELS QU'UN INCENDIE, UNE ELECTROCUTION, OU DES

BLESSURES CORPORELLES GRAVES. CONSERVEZ CE MODE D'EMPLOI EN CAS DE BESOIN ET

RELISEZ-LE SOUVENT POUR UTILISER VOTRE OUTIL EN TOUTE SECURITE.

NO UTILICE ESTA HERRAMIENTA HASTA HABER LEÍDO Y COMPRENDIDO TO

DAS LAS

INSTRUCCIONES Y NORMAS DE SEGURIDAD CONTENIDAS EN ESTE MANUAL. SI NO LO

HACE PODRÍA PROVOCAR ACCIDENTES CON FUEGO, DESCARGA ELÉCTRICA O LESIONES

PERSONALES SERIAS. GUARDE ESTE MANUAL DE INSTRUCCIONES PARA SU CONSULTA EN

EL FUTURO Y REVÍSELO FRECUENTEMENTE PARA UN USO SEGURO.

40732788-NA

1English1

English -1

THANKS FOR CHOOSING THIS PRODUCT

ACDelco provides you with products at an affordable price, and we would like you to

be fully satisfied with this product and our technical support. If any help or advice is

needed, please kindly contact us.

INTENDED USE

This tool is intended for personal and hand use only.

This digital torque tool display fastener torque specification settings, torque readings

and peak hold measurements. Recommended use it indoor.

GENERAL SAFETY RULES

READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below may result in

electric shock, fire and/or serious injury. The term "power tool" in all of the warnings

listed below refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS

The safety instructions provided in this manual are not intended to cover all possible

conditions and practices that may occur when operating, maintaining and cleaning

power tools.

Always use common sense and pay particular attention to all the DANGER,

WARNING, CAUTION and NOTE statements of this manual.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates an imminently hazardous situation which, if

not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if

not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

NOTE provides additional information that is useful for proper

use and maintenance of this tool. If a NOTE is indicated make

sure it is fully understood.

DANGER

NOTE

CAUTION

WARNING

1English1

English -2

WARNING LABEL IDENTIFICATION

Read Manuals Before Operating Product.

Wear Eye Protection.

Keep body stance balanced and firm. Do not overreach when operating this

tool.

The risk of hands, fingers or other body parts being caught or wrapped in

gear or other moving parts.

The risk of electrical shock.

Federal Communications Commission.

IMPORTANT SAFETY RULES

Risk of Flying Particles

WARNING: Over-torque can cause breakage. Force against flex stops on flex head

can cause head breakage. An out of calibration torque wrench can cause part or tool

breakage. Broken hand tools, sockets or accessories can cause injury. Excess force

can cause crow foot or flare nut wrench slippage.

WORK AREA

Keep children and bystanders away while operating a power tool. Distractions

can cause you to lose control.

Keep work area clean and well lit. Cluttered and dark areas invite accidents.

Do not operate digital torque tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Digital torque tools create sparks

which may ignite the dust or fumes.

WARNING

DANGER

1English1

English -3

ELECTRICAL SAFETY

Electrical shock can cause injury.

Plastic part is not insulated.

Do not use on live electrical circuits.

PERSONAL SAFETY

Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools

may result in serious personal injury.

Use personal safety equipment. Always wear eye protection. Safety equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations.

Do not expose digital torque tools to rain or wet conditions. Water entering a

digital torque tool will increase the risk of electric shock.

Ratchet mechanism may slip of break if dirty, mismatched or worn parts are

used, or direction lever is not fully engaged. Ratchets that slip or break can cause

injury.

Always pull-do not push- on the wrench handle and adjust your stance to

prevent a possible fall while applying torque.

WARNING

1English1

English -4

POWER TOOL USE AND CARE

For hand use only.

Do not apply excessive torque or force to the tool housing. The torque only

applies on the driver head.

Do not shake or shock.

Never use this digital torque tool to loosen fasteners.

This digital torque tool is for hand use only.

Always verify that the digital torque tool capacity matches or exceeds each

application before proceeding.

Always verify the calibration of the digital torque tool if you know or suspect its

capacity has been exceeded. To ensure accurate measurement periodic

recalibration is necessary.

Never force the head of flex head drive against stops.

Keep this digital torque tool away from magnets.

Do not apply excessive force to the LCD panel.

Use the digital torque tool only for the intended use described in this manual. Do

not use this digital torque tool as a hammer.

Do not use the digital torque tool if it is not working properly, or if it has

suffered any damage.

Be sure all components, including wrenches, extensions, drivers and sockets are

rated to match or exceed the torque being applied with tool.

Do not disassemble the digital torque tool.

Observe all equipment, system and manufacturer’s warnings, cautions and

procedures when using this digital torque tool.

Always using the correct size socket for the fastener being torqued.

Do not use damaged sockets, showing signs of wear or cracks.

Do not apply torque exceeding the rated capacity, regardless of whether the

digital torque tool is On or Off. Avoid shock load. Over-torque(110% of Max.

torque range) could cause breakage or lose accuracy.

Never operate digital torque tool when powered OFF. Always power digital

torque tool ON prior to applying torque.

Do not press ON/ZERO button while torque is being applied.

CAUTION

1English1

English -5

BATTERY TOOL USE AND CARE

Under abusive conditions, liquid may be ejected from the battery, avoid contact.

If contact accidentally occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the battery may cause irritation

or burns.

Do not expose this digital torque tool to dust or sand as this could cause serious

damage. Do not expose the digital torque tool to extreme temperature, humidity

direct sunlight or shock violently.

SERVICE

Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel may result in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow instructions

in the Maintenance section of this manual. Use of unauthorized parts or failure to

follow Maintenance Instructions may create a risk of shock or injury.

SPECIFIC SAFETY RULES AND SYMBOLS

Recommended operating temperature is -10-60°C (14-140°F).

Always replace damaged fasteners before applying torque.

SYMBOLS

The label on your tool may include the following symbols. The symbols and their

definitions are as follows:

SYMBOL NAME EXPLANATION

V Volts Voltage (potential)

kg Kilograms Weight

Direct Current Type of Current

CAUTION

1English1

English -6

FUNCTIONAL DESCRIPTION

CONTROLS AND COMPONENTS:

1. Reversible Ratchet 2 Quick Release Button

3. Forward and reverse selection lever 4. 1/2” Square Drive

5. Decoration Ring 6. Battery Cover

7. Handle 8. Anti-slip Handle

9. LED Indicator 10. Buzzer

11.LCD Panel 12.Button

13. Power/Reset Button 14. Memory Selection Button

15.Unit Selection Button 16. Mode Selection Button

17. Up Button 18. Down Button

19. Torque Value Display 20. Mode Display (*2)

21. Unit Display (*1) 22. Battery Display

23. Percentage Display 24. Memory Group Number Display

------*1 Measuring Units: ------*2 Modes:

1. N-m: Newton Meters 1. F: Trace Mode

2. kg-cm: Kilogram Centimeters 2. K: Peak Mode

3. lb-in: Inch Pounds 3. A: Angle Mode

4. lb-ft: Foot Pounds

2

3

11 12

8

19

21

23

22

15

16

17

24

20

9

13 14

18

10

1

4

5

7

6

1English1

English -7

SPECIFICATIONS

Model Number ARM303-4A ARM313-2A ARM315-3A ARM317-4A

Drive

1/2” Square 1/4” Square 3/8” Square 1/2” Square

Voltage

Head Type

Length

26-1/4" (666 mm) 16-1/8" (410 mm) 17-1/16" (434 mm) 17-7/8" (454 mm)

Accuracy ►CW

Accuracy ►CCW

Accuracy Angle

Operation Range Torque

12.5-250.7 ft-lbs (17-340 Nm) 1.11-22.12 ft-lbs (1.5-30 Nm) 5.0-99.5 ft-lbs (6.8-135 Nm) 5.0-99.5 ft-lbs (6.8-135 Nm)

Operation Range Angle

Memor y Capac i ty

LED

Vibration Warning

Resolution

Operation Mode

Power Saving Mode

Operating Temperature

Storage Temperature

Battery

Tool Weight

3.06 lbs (1.39 kg) 1.68 lbs (0.76 kg) 2.00 lbs (0.91 kg) 2.38 lbs (1.08 kg)

Model Number ARM319-6A ARM321-6A ARM323-8A

Drive

3/4” Square 3/4” Square 1” Square

Voltage

Head Type

Length

37" (940 mm) 48-5/8" (1235 mm) 48-13/16" (1240 mm)

Accuracy ►CW

Accuracy ►CCW

Accuracy Angle

Operation Range Torque

44.28-442.8 ft-lbs (60-600 Nm) 73.8-738 ft-lbs (100-1000 Nm) 73.8-738 ft-lbs (100-1000 Nm)

Operation Range Angle

Memor y Capac i ty

LED

Vibration Warning

Resolution

Operation Mode

Power Saving Mode

Operating Temperature

Storage Temperature

Battery

Tool Weight

8.38 lbs (3.80kg) 10.58 lbs (4.80 kg) 11.24 lbs (5.10 kg)

MINI (USE FOR TPMS)

Model Number ARM325-2I ARM327-3I ARM329-4I ARM331-2I

Drive

1/4” Square 3/8” Square 1/2” Square 1/4” Square

Voltage

3 Vdc

Head Type

Interchangeable

(For 9 x 12 mm Ins ert)

Interchangeable

(For 9 x 12 mm Insert)

Interchangeable

(For 14 x 18 mm Insert)

Interchangeable

(For 9 x 12 mm Ins ert)

Length

15-7/8" (403 mm) 16-3/4" (425 mm) 22" (559 mm) 10-1/16" (255 mm)

Accuracy ►CW

±3% (20% ~ 100% of full scale)

Accuracy ►CCW

±4% (20% ~ 100% of full scale)

Operation Range Torque

2.22-22.12 ft-lbs (3-30 Nm) 10-99.5 ft-lbs (13.5-135 Nm) 14.8-147.5 ft-lbs (20-200 Nm) 1.84-18.44 ft-lbs (2.5-25 Nm)

Memor y Capac i ty

30 data sets

LED

2 LED (GREEN + RED)

Vibration Warning

Reaching to 90% of Setting Value

Resolution

1 kg-cm, 0.1 N-m, 1 in-lb, 0.1 ft-lb

Operation Mode

Peak (K) / Trace (F)

Power Saving Mode

After 2 minutes of No Use

Operating Temperature

-10~60°C (14~140°F)

Storage Temperature

-20~70°C (-4~158°F)

Battery

AAA (Alkaline) Battery x 2

Tool Weight

1.65 lbs (0.75 kg) 1.98 lbs (0.90 kg) 2.98 lbs (1.35 kg) 0.60 lbs (0.27 kg)

INTERCHANGEABLE DIGITAL TORQUE WRENCH

±2% from 20% to 100% of full scale

±3% from 20% to 100% of full scale

30 data sets

2 LED (GREEN + RED)

AA (Alkaline) Battery x 2

3 Vdc

Peak (K) / Trace (F)

After 2 minutes of No Use

-10~60°C (14~140°F)

-20~70°C (-4~158°F)

Yes (While reaching to 90% of Setting Value)

1 kg-cm, 0.1 N-m, 1 in-lb, 0.1 ft-lb

3 Vdc

Quick Releas e Ratchet

±1.5% from 20% to 100% of full scale

±2.5% from 20% to 100% of full scale

+/-2

°

-20~70°C (-4~158°F)

AA (Alkaline) Battery x 2

2 LED (GREEN + RED)

Yes (While reaching to 90% of Setting Value)

1 kg-cm, 0.1 N-m, 1 in-lb, 0.1 ft-lb / 1

°

Peak (K) / Trace (F) / Angle (A)

2 LED (GREEN + RED)

Yes (Wh ile reaching to 90% of Setting Value)

1 kg-cm, 0.1 N-m, 1 in-lb, 0.1 ft-lb / 1

°

After 2 minutes of No Use

-10~60°C (14~140°F)

ANGLE DIGITAL TORQUE WRENCH

±2.5% from 20% to 100% of full scale

+/-2

°

720

°

30 data sets

3 Vdc

Quick Releas e Ratchet

±1.5% from 20% to 100% of full scale

Peak (K) / Trace (F) / Angle (A)

After 2 minutes of No Use

-10~60°C (14~140°F)

-20~70°C (-4~158°F)

AA (Alkaline) Battery x 2

720

°

30 data sets

1English1

English -8

ASSEMBLY

BATTERY INSTALL AND REPLACEMENT

Angle Series & Interchangeable Series (AA Battery x 2)

Mini Series (AAA Battery x 2)

1. Open battery cover.

2. Insert battery cells, make sure the polarity is correct.

3. Close the battery cover.

If doing the replacement, then do it reversely.

LOW VOLTAGE NOTIFICATION

It will display a low battery symbol in the upper right corner of the LCD display when

the battery voltage drops below 2.3 volts, and it will shut off after several seconds.

1English1

English -9

1. Remove the batteries if stored for a long period of time.

2. Keep spare batteries on hand when going on a long trip or to cold areas.

3. Do not mix the type of batteries or combine used batteries with new ones.

4. Sweat, oil and water can prevent a batteries’ terminal from making electrical

contact. To avoid this, wipe both terminals before loading a battery.

5. Battery life depends on battery quality and the amount of buzzer is used.

6. Dispose of batteries in a designated disposal area. Do not throw batteries into a

fire.

INTERCHANGEABLE HEAD INSTALL AND REPLACEMENT

1. Align the insert head with the interchangeable slot (as shown above).

2. Insert the head, make sure it is in position.

3. Close the battery cover.

4. If doing the replacement, press the steel ball to release the insert head first.

When replacing the head, turn off the power of the torque wrench.

WARNING

NOTE

1English1

English -10

OPERATION

To reduce the risk of injury, wear safety goggles or glasses with

side shields. Always remove battery pack before changing accessories or making

adjustments.

PRODUCT FUNCTIONS

Angle Series Interchangeable Series

Mini Series

Name of Function Key Function Description

C key Power and Reset

U/S key Unit Selection

M key Memory Selection

F/K/A key or F/K key Mode Selection

▲(UP) key Number Increasing

▼(DOWN) key Number Decreasing

POWER ON

Press C key to turn the digital torque tool on.

After the backlit LCD flashing, the display will be show 0000, and then enter the

operating mode. When this product is used for the first time, it will display the

product's smallest operating value after entering the operating mode. The units are

preset as N-m, the memory will display the first set, the mode will be tracking mode F,

the percentage position will display 0%, and the battery scale will show the voltage

detected at that time (all 30 memory data sets will have the same preset value).

WARNING

1English1

English -11

POWER OFF

Press C key and hold 3 seconds to switch off.

RESET

Press C key to reset (when device turned on)

HOW TO SELECT UNIT

Press U/S key to select N-m, Kg-cm, lb-in, and lb-ft; the preset unit is N-m.

Torque Unit Conversion Table

lb-in lb-ft N-m Kg-cm

1 lb-in

1 0.083 0.113 1.152

1 lb-ft

12 1 1.356 13.83

1 N-m

8.851 0.737 1 10.2

1 Kg-cm

0.868 0.072 0.098 1

MEMORY FUNCTION

All memory data sets are preset as the smallest value. To set a memory value, press the

M KEY, and the digit on the far right of the M-01 display will begin to flash; use ▲

(up) or ▼ (down) to select the memory data set (up and down keys can be held down

for continuous increasing or decreasing. Press the M Key after selected, will leave the

select mode to stop flash.

HOW TO SET TRACE MODE (F), PEAK MODE (K) OR ANGLE MODE (A)

TRACE MODE (F) (preset as trace mode at time of first use)

After setting a value (assuming the value is 50N-m), the force applied by the wrench

will gradually increase from 0000. When force is applied, the displayed value will

change as the user applies different amounts of force; the reading will increase as force

increased, and decrease as force decreased. The reading will jump to 50 N-m when the

user releases his grip and lets up.

PEAK MODE (K)

After setting a value (assuming the value is 50N-m), the force applied by the wrench

will gradually increase from 0000. When force is applied, the displayed value will

change as the user applies different amounts of force; the reading is the final torque

value. After the display flashes 10 seconds (no actions or buttons will be effective at

this time), it will automatic back to the original setting data or press the C key to return

to the selected value, or apply force again and the measured torque value will rise from

0000.

ANGLE MODE (A)

After setting a degree (assuming is 50°), the force applied by the wrench will gradually

1English1

English -12

increase from 0°. When force is applied, the displayed degree will change as the user

applies different amounts of force. It will cross-display the final degree and torque

value when user stops force the wrench, 10 seconds flashing (no actions or buttons will

be effective at this time), it will automatic back to the original setting data or press the

C key to return to the selected value, or apply force again and the measured angle

degree will rise from 0°.

MEASUREMENT RANGE SELECTION

Values can be freely selected as long as force is not being measured or memory

selection has not been performed. After completing torque measurement in either mode,

the selected value can be displayed.

▲(UP) / ▼(DOWN) SELECTION

Pressing the ▲ (up) key once will cause the value on the far right to increase by one;

pressing the key continuously will cause the value to increase continuously. Pressing

the ▼ (down) key once will cause the value on the far right to decrease by one.

LED & BUZZER

The green LED will come on and there will be a beep each time a key is pressed.

In the tracking mode, the two LEDs will be green and red. For example: when the set

torque value is 20N-m, the reading will begin to change from 0000 as soon as the user

begins to apply force. It approach the preset value 80%，the green light will now begin

to flash and the buzzer will be heard. As the applied torque approaches the preset value,

the green light will flash faster, and the buzzer will buzz faster. When the applied

torque reaches the preset value 100%, the green light will remain on and the buzzer will

continue to sound. When the torque exceeds the preset value (101%), the red light will

come on, and the buzzer will continue to sound; the buzzer sound will decrease

gradually as force is relaxed.

The peak mode is the same as the tracking mode, but the LED and buzzer will stop

once force is relaxed.

In the angle mode, the two LEDs will be green and red. For example: when the set

angle degree is 20°, the reading will begin to change from 0° as soon as the user begins

to apply force. It approach the preset value 80%，the green light will now begin to

flash and the buzzer will be heard. As the applied torque approaches the preset value,

the green light will flash faster, and the buzzer will buzz faster. When the applied reach

the preset degree 100%, the green light will remain on and the buzzer will continue to

sound. When it exceeds the preset degree (101%), the red light will come on, and the

buzzer will continue to sound; the buzzer sound will decrease gradually as force is

relaxed.

VIBRATION WARNING

For example : when if the set torque value is 20N-m, the reading will begin to change

from 0000, it will start to vibrate once the torque value reached to 90%, and it will stop

when the force is relaxed lower than 90% of preset value.

Vibration operation will automatically stop under angle mode.

1English1

English -13

LCD PERCENTAGE DISPLAY

The ordinary display is 0%

In tracking mode, if the set torque value is 20N-m, the display will show 50% after

force increases from 0N-m to 25N-m, and so on. The torque value will decrease after

force has been relaxed, and the display will return to the torque setting value after force

has completely relaxed.

The peak mode is the same as the tracking mode, but the displayed value will be the

percentage of the final torque after force is no longer applied, the Maximum is 100%.

In angle mode, if the set degree is 50°, the display will show 50% after force increases

from 0° to 25°, and so on. The displayed value will be the percentage of the final degree

after force is no longer applied, the Maximum is 100%.

LOW VOLTAGE DISPLAY

The LCD battery display has four increments. Greater or equal to 3V is shown as

completely charged; less than 2.8V is shown as 3 increments, less than 2.6V is shown

as 2 increments, and less than 2.4V is shown as one increment; when there is less than

2.3V, all functions will cease, and the instrument will turn off after the LCD battery

indicator flashes for 5 sec.

RESET MEMORY FUNCTION

Press and hold the C key + ▼ (down) key; after 5 sec., all values stored in memory

reset to the preset factory values.

BACKLIGHT SWITCH

Press the C key + ▲ (up) key to turn the backlight on or off; the backlight is preset as

on.

RESET

In order to make accurate data, press C key each time before using the device. On state

is prohibited to press C key to avoid get the error initial value.

POWER SAVING MODE

Enter power-saving mode after 2 minutes without using the device, press C key to

wake up.

OVERLOAD WARNING

Switch on or reset when screen continued to appear 110%, it means the device have

been forced exceeds the maximum standard torque value 110%, may result in the

products’ damage or accuracy error.

Under normal usage:

1English1

English -14

Overload:

USAGE

Illustration of using wrench handle:

P.S：Before completion of the booting process (see POWER ON), do not force in the

torque wrench.

WARNING NOTE FOR USING BATTERIES

1. Please take out the batteries, if the product is not used a long period of time.

2. Please prepare the more backup batteries, when the product is used in other places

without electric power.

3. Do not mix old and new batteries.

4. Do not use the soiled batteries with perspiration and greasiness.

5. Do not throw the batteries at fire, and the batteries have to be recovered.

6. The standard or rechargeable batteries can be used in our products.

7. If the LCD screen cannot display, please check whether the batteries are without

electricity, or replace them.

1English1

English -15

MAINTENANCE

In order to maintain accuracy of the tools, we recommend that

you conduct the calibration once a year.

Remove batteries before cleaning.

CLEANING AND THINGS TO REMEMBER

1. Use a soft, dry, clean-cloth clean the wrench and LCD panel.

2. Clean torque wrench by wiping. Do not immerse.

3. Store torque wrench in protective case at its lowest torque setting. Do not force

handle below lowest setting.

4. If the wrench gets wet, wipe it with a dry towel as soon as possible. The salt in

seawater can be especially damaging.

5. Do not use organic solvents, such as alcohol or point thinner when cleaning the

wrench.

6. Do not place the product nearby any magnetic products.

7. Do not exert heavy force or pressure on the LCD screen.

8. Do not use the products as striking tools.

9. Do not hit the products by using hammer or other tools.

10. Exceeding the largest standard torque value may result in the products’ damage or

accuracy error(110%).

11. Do not use near or place in water.

12. Do not place the product in the high temperature and damp environment or do not

expose the product to sunlight.

13. Do not place the product in the full dust or sand environment.

14. Do not violently shake or drop the product.

15. Please take out the batteries if the product is not used a long period of time.

16. Do not throw the batteries into fire, and the batteries have to be recycled.

17. Please read carefully the operating manual, and then follow the guides of the

manual, before using the digital torque wrench.

18. Off state is prohibited to use.

19. Do not use the additional tools to extend the length of the handle, such as: iron or

plastic pipe.

20. Do not touch any button when torque is exerted.

21. The digital torque wrench cannot be applied to the conductive tools.

LUBRICATE

The wrench’s internal mechanism is permanently lubricated during assembly. Do not

attempt to lubricate the internal mechanism.

WARNING

1English1

English -16

ACCESSORIES

Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may become hazardous when used on

another tool.

Recommended accessories for use with your tool are available at extra cost from your

local service center.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustments should be performed by certified service centers or other qualified

service organizations, always using identical replacement parts.

PROTECTING THE ENVIRONMENT

Before disposing of damaged, check with your state Environmental Protection Agency

to find out about special restrictions on the disposal of tool or return them to a certified

service center for recycling.

ACDelco, ACDelco Emblem and the ACDelco related graphics are General Motors

Trademarks used under license to Mobiletron Electronics Co., Ltd.

1Français1

Français -1

MERCI D'AVOIR CHOISI CE PRODUIT

ACDelco offre des produits à des prix abordables et nous espérons que ce produit et

notre support technique vous satisferont pleinement. Si vous avez besoin d'assistance,

n'hésitez pas à nous contacter.

UTILISATION PREVUE

Cet outil est uniquement prévu pour une utilisation personnelle et manuelle.

Cet outil dynamométrique numérique affiche les paramètres de spécification du couple

de serrage, les lectures de couple et les mesures de la retenue en crête. Il est

recommandé de l'utiliser en extérieur.

RÈGLES GÉNÉRALES DE SÉCURITÉ

LISEZ ET COMPRENEZ TOUTES LES

INSTRUCTIONS. Le non respect des instructions

listées ci-dessous risquera d'engendrer une électrocution, un incendie et/ou des

blessures graves. Le terme « outil électrique » dans tous les avertissements ci-dessous

réfère à votre outil électrique branché sur le secteur (avec cordon) ou à votre outil

électrique alimenté par une batterie (sans cordon).

CONSERVEZ CES INSTRUCTIONS EN CAS DE BESOIN FUTUR

SACHEZ RECONNAITRE LES SYMBOLES, LES MOTS, ET LES

AVIS DE SECURITE

Le but des instructions de sécurité fournies dans ce manuel n'est pas de couvrir tous les

cas possibles pouvant se présenter pendant le fonctionnement, la maintenance et le

nettoyage des outils.

Faites toujours preuve de bon sens et faites particulièrement attention aux instructions

marquées DANGER, AVERTISSEMENT, ATTENTION et AVIS dans ce manuel.

C'est le symbole d'alerte de sécurité. Il est utilisé pour vous

avertir d'un risque de dommages corporels. Obéissez à tous

les messages de sécurité qui suivent ce symbole pour éviter

tous risques de dommages corporels.

DANGER indique une situation dangereuse imminente qui, si

elle n'est pas évitée, risque d'entraîner la mort ou des

dommages corporels graves.

AVERTISSEMENT indique une situation potentiellement

dangereuse qui, si elle n'est pas évitée, risque d'entraîner la

mort ou des dommages corporels graves.

ATTENTION indique une situation potentiellement

dangereuse qui, si elle n'est pas évitée, risque d'entraîner des

dommages corporels mineurs ou modérés.

DANGER

ATTENTION

AVERTISSEMENT

1Français1

Français -2

AVIS fournit des informations supplémentaires utiles pour

l'utilisation et la maintenance de cet outil. Assurez-vous de

comprendre parfaitement les AVIS indiqués.

IDENTIFICATION D'ÉTIQUETTE D'AVERTISSEMENT

Lisez les manuels avant d'utiliser le produit.

Port de protection oculaire.

Positionnez votre corps de manière bien équilibrée et stable. Ne jouez pas

au plus malin lorsque vous utilisez cet outil.

Il y a un risque que vos mains, vos doigts ou d'autres parties de votre corps

soient prises ou s'enroulent autour de la boîte de vitesse ou d'autres

éléments en mouvement.

Risque de choc électrique.

Commission fédérale des communications (FCC en anglais).

RÈGLES IMPORTANTES DE SÉCURITÉ

Risque de particules volantes

AVERTISSEMENT: Un surcouple peut entraîner des cassures. Une force excessive

sur les arrêtoirs de la tête articulée peut entraîner une cassure de la tête. Une clé

dynamométrique qui n'est plus étalonner peut entraîner une cassure de l'outil ou d'un

composant. L’utilisation d’outils manuels, de douilles ou d’accessoires cassés risque

d'engendrer des blessures. Une force excessive peut causer un glissement du pied-de-

biche ou de la clé polygonale ouverte.

ESPACE DE TRAVAIL

Gardez les enfants et les spectateurs hors d'atteinte pendant le fonctionnement

d'un outil électrique. Des distractions peuvent vous faire perdre le contrôle.

Gardez votre espace de travail propre et bien éclairé. Le désordre et le manque

d'éclairage sont des conditions propices aux accidents.

N'utilisez pas les outils dynamométriques numériques dans des endroits ou il y a

des risques d'explosion, comme en présence de liquides inflammables, de gaz ou

de poussière. Les outils dynamométroques numériques font des étincelles qui

risquent d'enflammer les poussières ou les émanations.

AVERTISSEMENT

DANGER

AVIS

1Français1

Français -3

SÉCURITÉ ÉLECTRIQUE

Un choc électrique risque de vous blesser.

Le composant en plastique n'est pas isolé.

N'utilisez pas l'outil sur des circuits électiques sous tension.

SÉCURITÉ PERSONNELLE

Restez attentif, faites attention à ce que vous faites et utilisez votre bon sens

lorsque vous utilisez l'outil électrique. N'utilisez pas un outil électrique quand

vous êtes fatigué ou sous l'influences de drogue, d'alcool ou de médicaments. Un

moment d'inattention pendant l'utilisation de l'outil électrique peut engendrer des

blessures corporelles graves.

Utilisez des équipements individuels de sécurité. Portez toujours des protections

pour vos yeux. L'utilisation d'équipement de sécurité comme un masque anti-

poussière, des chaussures de sécurité anti-dérapantes, un casque de sécurité ou des

protections auditives réduiront les risques de blessures corporelles.

Ne jouez pas au plus malin. Gardez constamment vos appuis et votre équilibre.

Ceci permet de mieux contrôler votre outil électrique dans des situations inattendues.

N'exposez pas les outils électriques à la pluie ou à l'humidité. Toute pénétration

d'eau à l'intérieur de l'outil augmentera les risques de choc électrique.

Le mécanisme de cliquet peut glisser ou casser si des composants sont sales, mal

adaptés ou usés, ou si le levier de direction n'est pas engagé à fond. Des cliquets

qui glissent ou cassent risquent de vous blesser.

Tirez mais ne poussez pas sur la poignée de la clé et réglez votre mise au point

pour éviter une chute lors de l'application du couple.

UTILISATION ET ENTRETIEN D'UNE BATTERIE

Prévu uniquement pour une utilisation manuelle.

N'exercez pas un couple ou une force excessive sur la coque de l'outil. Le couple

s'applique uniquement sur la tête.

Ne pas secouer et ne pas cogner l'outil.

N'utilisez jamais cet outil dynamométrique numérique pour desserrer des

éléments de fixation filetés.

Cet outil dynamométrique numérique est uniquement prévu pour une

utilisation manuelle.

ATTENTION

AVERTISSEMENT

La page charge ...

ACDelco ARM317-4A Product Information Manual

Ce manuel convient également à

ACDelco ARM317-4A Product Information Manual

dans d''autres langues

Documents connexes

Autres documents