Krups XP1500US Manuel utilisateur

Marque: Krups

Modèle: XP1500US

Catégorie: Cafetières

Taper: Manuel utilisateur

www.krups.com

e10

Optional accessory XP 1530 only

C1 C2 C3 C4

XP 1530 only

11 12

2 3

5 6

17 18

English 6

Instructions for Use

Limited Warranty

Espresso XP1500/1530

Mode d’emploi

Garantie

Español 33

Instrucciones de uso

Garantía

Français 19

Español

summary.PM6.5 16/03/05, 10:535

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should

always be followed to reduce the risk of fire, electric shock and/or

injury to persons, including the following:

1- Read all instructions and information in this instruction book

and any other literature included in this carton referring to this

product before operating or using this appliance.

2- Do not touch hot surfaces. Use handles or knobs.

3- To protect against fire, electric shock and personal injury do not

immerse cord, plugs or appliance in water or other liquid.

4- Close supervision is necessary when any appliance is used near

children. Keep this appliance out of the reach of children.

Product not intended for use by children.

5- Unplug from outlet when not in use and before cleaning.

Allow to cool before putting on or taking off parts, and before

cleaning the appliance.

6- Do not operate any appliance with a damaged cord or plug or

after the appliance malfunctions, or has been damaged in any

manner. Return appliance to your nearest authorized KRUPS

Service Center for examination, repair or adjustment (see

Limited Warranty).

7- The use of an accessory not evaluated for use with this

appliance may result in fire, electric shock or injury to persons.

8- Do not use outdoors.

9- Do not let cord hang over edge of table or counter or touch hot

surfaces.

10- Do not place on or near a hot gas or electric burner, or in a

heated oven.

11- To disconnect, turn control to “OFF”, then remove plug from

wall outlet.

12- Do not use appliance for other than intended use.

13- Do not unscrew or remove boiler cap while the machine is in

operation. Wait until brewing cycle is completed and all water

and steam has been used up. Remove boiler cap only after

insuring that remaining steam pressure was released through

steam nozzle.

English

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:526

14- Appliance for household use only, do not immerse in water.

• Appliance with Glass carafe.

A. The carafe is designed for use only with this appliance. It must

never be used on a range top.

B. Do not set a hot carafe on a wet or cold surface.

C. Do not use a cracked carafe or a carafe having a loose or

weakened handle.

D. Do not clean carafe with harsh cleansers, steel wool pads, or

other abrasive material.

SAVE THESE INSTRUCTIONS

SPECIAL CORD SET

INSTRUCTIONS

Regarding your Cord Set:

A. A short power-supply cord is provided to reduce risks resulting

from becoming entangled in or tripping over a longer cord.

B. Longer extension cords are available and may be used if care is

exercised in their use.

C. If a long extension cord is used, (1) the marked electrical rating of

the extension cord should be at least as great as the electrical

rating of the appliance, (2) if the appliance is of the grounded

type, the extension cord should be a grounding-type 3-wire cord,

and (3) the longer cord should be arranged so that it will not

drape over the counter top or table top where it can be pulled on

by children or tripped over.

D. This appliance has a polarized plug (one blade is wider than the

other). As a safety feature, this plug will fit in a polarized outlet

only one way. If the plug does not fit fully in the outlet, reverse

the plug. If it still does not fit, contact a qualified electrician. Do

not attempt to defeat this safety feature.

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:527

CAUTION

This appliance is intended for household use only. Any servicing

other, than cleaning and user maintenance should be performed by

an authorized service representative.

•To reduce the risk of fire or electric shock, do not remove the base.

No user serviceable parts inside. Repair should be done by

authorized service personnel only.

•Check voltage to be sure that the voltage indicated on the name

plate agrees with your voltage.

•Never use warm or hot water to fill the water container! Use cold

water only !

•Never refill the water chamber while this coffeemaker is in the

«on» position. Turn the coffeemaker off and let it cool down for

ten minutes before refilling with water.

•Do not place carafe on a hot surface or in a heated oven.

•Before turning your KRUPS coffeemaker on, please make sure that

carafe sits flat on inside circle of heating plate.

•Never remove carafe before brewing is completely finished (this is

the case when dripping from the filter holder into the carafe has

stopped completely).

•Never clean with scouring powders or hard implements.

•Never use a microwave oven to warm up beverage in either the

espresso or the coffee carafe.

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:528

CAUTION – PRESSURE

Never open boiler cap (e1) or remove

filter holder (e9) while your appliance is

turned «on» or as long as there is pres-

sure in the boiler container.

Never move or remove the filter holder

while the appliance is in operation and

under pressure.

Please follow the instructions listed

below to see if the machine is still under

pressure. Follow these safety precautions

while your machine is in use and ten to

fifteen minutes after last use.

Turn the selector knob (S) to the OFF

position.

Carefully open the steam release knob (e2)

by turning it counter clockwise. If steam

comes out of the nozzle, then the boiler

chamber is still under pressure. Close steam

knob and proceed with instructions listed

below.

Take a pitcher filled with cold water and

hold it underneath the steam nozzle with

nozzle inserted into the pitcher. Then open

the steam release knob (e2) by turning it

counter clockwise. Leave steam release

knob open until no more steam comes out

of nozzle. When finished turn steam knob

clockwise to close.

Now you can remove the boiler cap and the

filter holder.

Genuine Espresso

Espresso is a far richer and stronger brew than

regular coffee. It should be deep, dark, and

delicious. Most people find that they enjoy it

in small quantities because of its richness, and

for that reason, espresso is usually served in

small (2-2 1/2 oz) demi-cups.

Your appliance when properly used, will

produce espresso that is deep, dark and

delicious. Just follow the instructions and use

fresh, well-roasted, pre-ground espresso.

Preparing espresso or cappuccino is different

from brewing regular drip coffee. One main

difference is that the water will come to a boil

and will then be forced through the ground

coffee. This means that an espresso machine

Description :

Espresso : e

e1- Boiler security cap

e2- Steam side knob

e3- Steam nozzle

e4- Cappuccino nozzle

e5- Espresso jug lid

e6- Espresso carafe

e7- Drip grid

e8- 2-4-cup sieve

e9- Sieve holder

e10- Measuring spoon

S- Selector knob

C- Display

Coffee : c

c1- Optional accessory : Duo-Filter –

Ref : F15A04 (sold separatly)

c2- Watertank drip coffee

c3- Filter basket

c4- Swing-out filter holder

c5- Waterlevel indicator

c6- Pause and Serve device

c7- Drip carafe hinged lid

c8- Drip carafe

c9- Non-stick coated keepwarming plate

Before First Use

Please familiarize yourself with all parts of

your Krups espresso machine prior to use.

Insert the filter basket into the filter holder, fit

the filter holder into the filter rings, remove

and replace the boiler cap. Check the different

positions of the switch. To remove any

residuals of production which may rest in the

appliance, run the machine through one or

two cycles with water only. Wash all loose

parts in warm soapy water, rinse thoroughly

and dry.

Read all instructions, cautions, notes and

attentions before actually using the

machine.

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:529

works under pressure and needs special

attention.

CAUTION-HOT

Do not touch boiler cap (e1) during

operation. Before removing boiler cap

turn off machine, let it cool down for at

least 2 or 3 minutes. Relieve pressure. See

CAUTION-PRESSURE.

Making the Perfect Cup of

Coffee

Making the perfect cup of coffee is something

different for everyone. It is an art and a

science, that is not only effected by the coffee

that is used, but also the equipment. The

water, the water temperature, the time the

water is in contact with the coffee, the grind,

the type of filter, all play an important role in

determining the flavor. Fine tuning these

aspects is the art of making the ultimate cup

of coffee.

The four main principles :

1. The Water

It is important to use fresh water. Since coffee

is 98% water, any residual flavors will come

through in the coffee. The Duo Filter (not

delivered with this appliance, yet available as

an accessory) System can remove chlorine

taste, but the better the water you start with

the better the flavor of the coffee.

2. The Coffee

Choose premium fresh whole beans suited to

your taste. There are two principale species of

coffee: Arabica and Robusta. Arabica beans

are the choice beans with more flavor and less

caffeine. Robusta beans have more caffeine

and are more « robust » and are usually used

in blends. The origin of the beans and the

roast will determine the flavor. Roasts vary

from light to very dark. Light roasts have a

smooth, delicate aromatic taste, medium to

medium dark roasts are slightly stronger, with

a full-bodied balanced taste, and dark roasts

are bold with smoky undertones.

3. The Grind

Use the proper grind finesse and grind just

prior to brewing. The variation in the grind

depends on the type of filter you use. We

prefer paper filters because they allow you to

use a finer grind, thus allowing a full extrac-

tion and more contact time with the water.

Permanent filters require a slightly coarser

grind therefore the extraction rate is reduced.

A general rule of thumb for grinding is the

longer the brew process the coarser the grind.

4. The Proportion

We recommend that you use 1 rounded Tbsp.

of ground coffee per cup and modify the

quantity to suit your taste.

COFFEE

Special features

The following features are available only on

the XP 1530.

Programming Clock and coffee strengh

Your XP 1530 Krups appliance is equipped

with electronic controls providing comfort and

range of setting with 3 push buttons (1).

- clock setting mode for day time and coffee

cycle automatic start (C1)

- hours and automatic start mode selection

(C2)

- minutes and coffee strength selection (C3)

- display for feedback to user (C4)

- clock setting for day time is adjustable once

the appliance is plugged with display

blinking.

Press the (C1) button to enter clock setting

mode. Then press (C2) to adjust hours and

validate with (C1) button. Press (C3) to adjust

minutes and validate with (C1) buttons.

Setting can be done either with impulse or

continuous actuation of hours and minutes

buttons.

Once day time is set, you are invited to set the

automatic start time, with display blinking and

clock icon in display.

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5210

You can either choose to set automatic start

time immediately by repeating above -

operations, or choose to do the setting later by

pushing the clock mode button (C1) twice.

To activate the automatic coffee start at preset

time, simply activate the automatic mode

button (C2). To shut off appliance that started

in automatic mode, press the button (C2).

Coffee Strength

Your XP1530 KRUPS appliance is equipped

with Coffee strength mode button.

You can choose to brew an extra strong cup of

coffee by activating the strong coffee mode

(C3). A coffee cup icon is displayed on top left

of the display (10).

To come back to regular coffee just press again

the strong coffee mode button (C3).

This is normally used only with a small quantity

of water (max 4 cups).

Automatic stop

Your XP1530 KRUPS appliance is equipped

with automatic shut off.

2 hours after switching ON drip coffee

function, the appliance will switch OFF

automatically. In that case you need to turn

the selector knob (S) in OFF middle position

before making a new coffee cycle.

You can also turn the selector off as soon as

the coffee is ready.

Preparing Coffee

We recommend rinsing the coffee machine by

running one or two cycles with water only,

without ground coffee in the filter basket.

Be sure that the water chamber is empty.

Remove any literature, etc if found in the

water chamber.

The lid of the glass carafe must be properly

positioned during the brewing process.

To open the lid press the flap on top of

handle.

Make sure that the swivel filter is closed

properly during the brewing process. Push

in firmly until the handle touches the side

of the coffee maker and filter «clicks» into

place.

Caution : If the swivel filter is not

closed in properly the «Pause and

Serve» can not function. This may cause

hot water or hot coffee to overflow.

The «Pause and Serve» mechanism is

opened as long as the glass carafe is inserted

into the machine and sits properly on the

warming plate and the swivel filter is closed

properly. When brewing coffee make sure

the glass carafe is in place (see «Pause and

Serve» section).

Place your appliance near an electrical outlet

and release enough cord so that you can plug

in the machine (2).

Putting in the ground coffee

1.Swing out the filter holder (3) and insert a

paper filter in the filter basket. We

recommend using KRUPS size 4. When

inserting a paper filter make sure the seam is

pointing toward the base of the filter holder

(4).

Use your hands to conform the filter to the

contours of the filter basket. This will enable

you to achieve better results.

2.Put ground coffee into the filter basket (5).

We suggest using one level KRUPS

measuring spoon of ground coffee for each

cup of robust brewed coffee. You can adjust

the quantity to suit your own taste.

We do not recommend using coffee that is

ground to a powder-like consistency, as this

will prevent water from passing through the

filter.

3.Close the filter and make sure that it is

completely closed (6).

ATTENTION :

Make sure that the filter paper does not fold

over when closing the swivel filter, otherwise

the water might run between the filter paper

and the filter holder producing a very weak

cup of coffee.

Filling the Water Chamber

1.Open the hinged lid (7). Pour in the desired

quantity of water (8) and close the lid. The

amount of freshly brewed coffee delivered

after the brewing process will always be

slightly less than the amount put into the

water chamber. This is due to the minimal

absorption of the water by the ground

coffee. The water levels on drip carafe and

appliance do take this absorption in account

for more convenience.

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5211

2.Place the glass carafe with lid in position on

the warming plate.

3.Turn « ON » your appliance in drip coffee

mode using the selector knob (S). The

indicator light will illuminate indicating that

the brewing process has begun (9).

4.As long as the blue indicator light is

illuminated the coffee will be kept warm.

Pause and Serve Feature

The Pause and Serve feature automatically

stops the flow of brewed coffee through the

filter cone if the glass carafe is removed from

the warming plate during the brewing cycle.

You have about 20 seconds between the

removal of the carafe and it being reinserted

back onto the warming plate.

The Pause and Serve device closes off the filter

cone so effectively that there is virtually no

coffee dripping onto the warming plate. Once

the carafe is replaced, the brewing process

and the flow of coffee into the carafe will

resume.

CAUTION

If significant amounts of coffee drip onto the

warming plate afer the carafe has been

removed, please check the seal in the filter

holder to ensure it is placed properly. If a

requirement seal is needed, please contact

one of our main service centers or our main

parts center.

If the filter is overfilled with coffee grounds, it

could cause the water that jets into the filter

cone to overflow between the filter and the

sides of the filter cone. Be sure to use the

proper amount of ground coffee.

If this blockage and subsequent dripping does

occur, put the glass carafe immediately back

onto the warming plate, and allow the full

brewing cycle to run its course. Do not swing

out the swivel filter until the brewing process

is completed.

Cleaning the coffeemaker

Always unplug this appliance before

cleaning. Clean the filter basket, carafe, and

lid in a solution of warm water and mild

liquid soap. These parts can also be placed in

the upper level of your dishwasher away

from the heating and drying element for

safe effective cleaning.

Never use scouring agents.

Never immerse the appliance itself in water.

To clean, simply wipe off with a soft, damp

cloth.

Never use a cloth to clean inside of the

water chamber, as this might leave residual

deposits in the chamber. Just rinse with cold

water periodically.

Decalcifying the

coffeemaker

The warranty does not cover faulty or

broken machines that are not properly

descaled.

The coffeemaker must be decalcified regularly.

The frequency depends on the hardness of

your water and how often you use the

coffeemaker.

Recognizable indications that descaling is

necessary are :

- increase noise during boiling,

- longer preparation time.

If usage is frequent, descaling should be

carried out as follows :

- with soft water once a year,

- with medium hard water every quarter year,

- with hard water once a month.

In doubt regarding the water hardness in your

area, you may call your local water

department.

As descaling agent we recommend the use of

reference solution N°F054 from Satisfusion 1

Service at 888-344-0727.

Dissolve a packet of Krups descaling solution

in 1/2 quart water and pour into the water

container. Run this through 2 or 3 times as if

making coffee, but using no ground coffee.

The hot descaling solution must be allowed to

cool down before being poured into the

water container. Finally do the same twice

using clear water.

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5212

ESPRESSO

Making espresso

1.Place your appliance near an electrical outlet

and release enough cord so that you can

plug in the machine (2).

2.Place the filter basket (e8) into the filter

holder (e9) and rotate basket inside filter

holder to secure it (11).

3.Fill with ground espresso. The filter basket is

marked on the inside for 2 and 4 cups. Pack

the coffee lightly and clear any excess coffee

from the rim of the filter holder. This will

assure proper fit to the brewing head

(12).

ATTENTION !

Do not pack coffee too tightly.

Do not fill more coffee than indicated by

the four-cup marking into the filter

basket. This might cause clogging or

overflow.

4.To insert the filter holder, place the filter

handle’s to the left, raise the filter holder up

into brewing head and turn the filter holder

to the right, until it can go no further.

If the filter holder’s handle does not point

toward you in lock position, do not operate

the machine. Rather, remove the filter holder

and reinsert it as described above (13).

By following this procedure this will

prevent the filter holder from being

dislodged as pressure builds up during

the brewing process.

5.Open the hinged lid and unscrew the boiler

cap by turning it counterclockwise

(14+15).

6.Fill the boiler container with cold water

using the marking indicated on the glass

carafe (16).

CAUTION

Never fill the boiler while your appliance

is switched on.

Never fill more than 20 oz of water into

the boiler.

The glass carafe has markings for 2 and 4

cups.

To froth milk for Cappuccino preparation, add

the quantity of water corresponding to the

steam level marking on the carafe.

Maximum capacity to the bottom of the metal

band around the glass carafe = 4 cups of

espresso, plus steam for frothing milk for

cappuccino.

CAUTION

Never fill the carafe above the bottom of

the metal band!

NOTE

It is very important to fill only the amount of

water you need into the boiler. Your appliance

will always need to process all the water

until the boiler is empty.

7.Close the boiler cap securely by turning it

clockwise (17).

8.Place carafe under the filter holder and

make sure the slot on carafe lid is right

below the filter holder output (18).

ATTENTION :

Make sure the overflow grid (e7) is in

place.

9. Make sure the side knob (e2) is set on cup

Espresso position. Then turn the selector

knob (S) to the left in Espresso ON position.

The left indicator will light ON blue (19).

It will take approximately 2 minutes for the

water to be heated. The water will then be

forced through the ground coffee into the

glass carafe.

10. Wait until all the water in the boiler has

been used. Switch off the machine by

turning the selector knob (S) in middle

position.

11. Do not unscrew the boiler cap while

the machine is in operation. Wait until

brewing cycle is completed and all

water and steam have been used (see

CAUTION-PRESSURE).

CAUTION

Use caution when removing the filter

holder, as the metal parts may still be hot.

After switching off the appliance it is

recommended to wait about 2 minutes

before removing the filter holder. To

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5213

remove the filter holder, turn the filter to

the left, until the holder dislodges from

the machine.

Cappuccino

Cappuccino reportedly takes its name from

the chocolate hues of the robes worn by the

Capuchin monks who favored this delicious

dessert coffee. Cappuccino is traditionnally

made up of 1/3 espresso, 1/3 steamed milk

and 1/3 froth and can be tailored to one’s

own taste with cinnamon, sugar, chocolate

flakes or even liquor. Its versatility makes

cappuccino a world wide gourmet choice.

Making Cappuccino

If the Cappuccino nozzle is not attached,

attach it now (20).

1.Pour 4 to 6 oz of fresh, cold milk into a

small pitcher. Do not use a pitcher cleaned

with hot water and still warm. The pitcher

should fit underneath the cappuccino

nozzle. We recommend using 2% or skim

for a stiff, dense froth. Use regular whole

milk if you prefer a creamy froth.

2.Follow the directions from step 1 to 12 in

section « Making Espresso ».

3.As soon as the first few drops of coffee are

forced through the filter holder you can start

frothing the milk.

Place the tip of the steam nozzle half way

into the pitcher of milk.

4a) Turn the steam release knob (e2)

counterclockwise to release steam(21).

b) Keep pitcher slightly tilted so that you

can always see the position of the nozzle

as you froth the milk.

Always ensure some clearance between

the cappuccino nozzle end and

bottom wall of the pitcher, to allow

steam exhaust.

In just a few seconds, your milk will

begin to froth. As the froth rises, keep

lowering the pitcher so that the tip of

the steam nozzle is always just slightly

beneath the surface of the rising froth.

Note : Do not bring milk to a boil (this

will happen if large bubbles start to form

on the surface of the milk).

c) When you have finished frothing milk,

close the steam release knob by

turning it clockwise while the nozzle is

still immersed in the milk. This willavoid

splattering of the hot milk and froth.

d) If you prefer «stiff» froth, let the frothed

milk stand for a minute.

ATTENTION :

Clogged steam nozzle

Milk residuals will build up in the tip of the

steam nozzle after frothing milk. To avoid

clogging, remove the plastic housing of the

cappuccino nozzle (22) once appliance is cold,

for easy cleaning. Then follow «cleaning the

steam nozzle» as described in the section

«Cleaning the cappuccino nozzle».

Don’t forget to replace the tip of the nozzle

and screw on tightly (23).

Steaming without making

Espresso (Steamplug)

CAUTION

Make sure your appliance is cool and all

pressure has been released (see CAUTION-

PRESSURE).

1.Fill the boiler container with cold water.

CAUTION

For steam only, do not fill the glass carafe

above the 2-cups marking. This amount

will always provide enough steam for

frothing.

2.Have your pitcher with milk ready to heat.

3.Place glass carafe, with lid under filter

holder (18). Make sure the side knob (e2) is

set on cup Espresso position. Then turn the

selector knob (S) to the left in Espresso ON

position. The left indicator will light ON blue

(19).

4.Open the steam release knob immediately

after turning the machine on. Stand by with

your frothing pitcher.

CAUTION :

Do not leave the machine unattended at

this time.

It will take approximately 30 to 60 seconds

after turning the machine on for the steam

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5214

to come out of the steam nozzle. Proceed

with steps 4.a) and 4.b) in the section

« Making Cappuccino ».

5.When all steam is released, close the steam

release knob and turn off the machine.

Caution :

If you do not need all the water for

steaming, proceed as follows:

a) turn off the machine.

b) release the remaining steam pressure into

another container.

Do not close the steam release knob

before all steam is released or machine

has been turned «off»! (See section –

CAUTION - PRESSURE)

ATTENTION !

The plastic housing of the cappuccino nozzle

(e4) has 2 fine holes on sides which draw air

into the milk.

If those holes get clogged, the milk will not be

frothed properly. Therefore, do not dip the

cappuccino nozzle in milk or froth up to those

holes.

Cleaning the espresso and

cappuccino side

Before cleaning, turn «off» the machine,

unplug it, and allow it to cool down.

The filter holder, filter basket, carafe, carafe lid

and overflow lid must not be cleaned in dish

washer. Only use hot water and gentle soap.

Never use abrasive materials.

The machine can be wiped clean by using a

damp cloth. Never immerse the body of your

«appliance» in water or any other liquid.

Clean the brewing head with a damp cloth

and remove ground coffee. If there is water

left in the boiler chamber, let the machine

cool down, remove all those parts and empty

through the top opening by turning upside

down.

Cleaning the Cappuccino nozzle

Clean the steam nozzle each time after you

have immersed it in the milk, otherwise the

inside of the nozzle becomes clogged and the

milk deposits on the outside harden and

become difficult to remove.

If clogging does occur, remove the plastic

housing of the cappuccino nozzle (22) once

appliance is cold and then unscrew the tip of

the steam nozzle (23).

Remove all milk particles using a sewing

needle and rinse under the faucet. Replace

nozzle tip making sure to screw it on tightly.

Wipe off the outside of the nozzle with a wet

cloth. Hold the wet cloth very close to the tip

of the nozzle and open the steam valve. Let

the steam escape into the wet cloth for one or

two seconds, then close the valve. Any milk

residue will then be flushed out. The plastic

housing of the cappuccino nozzle should be

rinsed in warm water. If the small suction

openings are clogged up, it can be opened

with a small needle.

Cleaning the drip tray

The overflow grid and the cavity under he

grid can be cleaned by removing the grid

(24).

CAUTION

Do not try to open or disassemble the

main body of the machine.

Decalcifying the

espresso side

The warranty does not cover faulty or

broken espresso machine due to not

being descaled.

• Due to the acid substance, we recommend

protecting your worktop and sink unit

during the descaling process, especially if it

is made of marble or stone. Isolate your

espresso with a tea towel, a tablecloth or a

tray.

The espresso machine must be decalcified

regularly. The frequency depends on the

hardness of your water and how often you

use the espresso machine.

Before descaling, the brewing sieve on the

brewing head must first be screwed off.

1.Remove all lime and coffee residues from

the brewing sieve and the brewing head.

2.Remove the plastic housing of the cappuc-

cino nozzle (22).

As descaling agent we recommend the use of

reference solution N°F054 from Satisfusion 1

Service at 888-344-0727.

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5215

3.Dissolve a packet of Krups descaling

solution in 10 oz / 300 ml of lukewarm

water and pour into the boiler container. Put

one receptacle under the brewing head and

another under the steam nozzle.

(Note : Do not use the filter holder during

decalcification.)

4.Open the steam valve and turn on the

appliance. Allow the descaling solution to

run out of the espresso outlet and the steam

nozzle.

5.After each brewing cycle, switch off the

appliance and allow the appliance to cool

down.

6.Repeat this operation once again.

Following this, allow 2 boiler container of

clear water to run through the system. Switch

off the appliance. Allow the appliance to cool

down. Insert the brewing sieve into the

brewing head again and push the plastic

housing of the cappuccino nozzle onto the

steam nozzle.

Troubleshooting

(Always check if the appliance is plugged

in and is in the proper (on) position).

Problem :

1. Espresso leaking from filter holder.

Cause :

Filter holder not properly inserted.

Filter holder not pushed in far enough.

Internal gasket is dirty and needs to be

cleaned.

Gasket without elasticity, replace it with a

new one.

Coffee powder not cleaned off the edge of

the filter holder.

Problem :

2. Espresso does not come out.

Cause :

No water in boiler container.

No coffee in filter holder.

Filter clogged because coffee ground is too

fine and or pressed down too hard

Problem :

3. Steam does not come out of steam nozzle.

Cause :

No water or not enough water in the boiler

chamber.

Steam nozzle is clogged (see «Cleaning

the cappuccino nozzle » section).

Problem :

4. Not enough froth when frothing the milk.

Cause :

Steam nozzle touches the bottom of

the pitcher.

Steam nozzle is clogged : tiny holes on top

of plastic housing of the cappuccino nozzle

are clogged (see «cleaning the cappuccino

nozzle»)

Milk is not fat enough or too warm (more

than 8°C).

For best results .....

....Always use fresh, cold water (warm water

might be stale and have mineral deposits

which would impair the flavor of the coffee)

... We recommend that you grind your own

beans. Freshly ground beans deliver more

aroma and flavor. Use one KRUPS measuring

scoop of beans per cup.

....Serve coffee immediately after brewing.

....Never reheat coffee.

Accessory

Optional accessory, sold separatly : Duo Filter

ref F15A04.

Anti chlorine and anti-scale filter optimizes

coffee taste and reduces the frequency of

descaling and maintenance.

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5216

LIMITED WARRANTY

This Krups product is warranted for 1 year from the date of

purchase against defects in material and workmanship. During this

period, the Krups product that, upon inspection by Krups, is

proved defective, will be repaired or replaced, at Krups’ option,

without charge to the customer. If a replacement product is sent, it

will carry the remaining warranty of the original product. This

warranty does not apply to any defect arising from a buyer’s or

user’s misuse of the product, negligence, failure to follow Krups’

instructions, use on current or voltage other than that stamped on

the product, wear and tear, alteration or repair not authorized by

Krups, or use for commercial purposes.

THE WARRANTIES SET FORTH HEREIN ARE EXCLUSIVE AND NO

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT

LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE OR USE, ARE MADE BY KRUPS OR

ARE AUTHORIZED TO BE MADE WITH RESPECT TO THE PRODUCT.

Some states do not allow limitation on how long an implied

warranty lasts or do not allow the exclusion of incidental or

consequential damages, so the above limitations may not apply to

you. This warranty gives you specific legal rights, and you may

also have other rights, which vary from state to state.

If you believe your product is defective, bring the product (or send

it, postage prepaid) along with proof of purchase to the nearest

authorized Krups Service Center. (Please contact your respective

countries customer service department, indicated below, for the

address of the nearest authorized Krups Service Center.)

If you send the product, please include a letter explaining the

nature of the claimed defect.

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5217

If you have additional questions, please call our Consumer Service

Department:

USA: 1-800-526-5377;

Mon – Fri 8:00 a.m. –6:30 p.m. (EST).

www.KrupsUSA.com

Please note hours are subject to change.

Before calling the Consumer Service Department, please have the type

number of your KRUPS appliance available. You must have this informa-

tion before calling our Consumer Service Department so that we may

better answer your questions. The type number can be located by looking

at the bottom of your appliance.

Any general correspondence can be addressed to:

USA:

Krups

196 Boston Avenue

Medford, MA 02155

Only letters can be accepted at this address. Shipments and

packages that do not have a return authorization number will be

refused.

Canada: 1-800-418-3325;

Mon – Fri 8:30 a.m. – 4:30 p.m. (EST)

www.Krups.ca

Canada:

Groupe SEB Canada Inc.

455 Finchdene Square

Scarborough, Ontario M1X 1B7

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5218

PRECAUTIONS IMPORTANTES

Lors d’utilisation d’appareils électriques, certaines règles élémentai-

res doivent être respectées pour éviter les risques d’incendie, de

choc électrique et de blessures, et en particulier les suivantes :

1- Lire toutes les directives et les renseignements de ce manuel

ainsi que tout autre document inclus dans la boîte avant

d’utiliser l’appareil.

2- Ne pas toucher les surfaces chaudes. Utiliser les poignées ou les

boutons.

3- Pour se protéger d’un risque d’incendie, de choc électrique et de

blessure, me pas immerger le cordon, la fiche ou l’appareil dans

l’eau ou dans tout autre liquide.

4- Une supervision étroite est requise lorsque l’appareil est utilisé

par ou à proximité des enfants.

5- Débrancher l’appareil de la prise murale lorsqu’il n’est pas

utilisé et avant de le nettoyer. Laisser l’appareil refroidir avant

de placer ou de retirer des pièces et avant de le nettoyer.

6- Ne pas faire fonctionner un appareil dont le cordon ou la fiche

est endommagé ou si celui-ci ne fonctionne pas correctement

ou s’il a été endommagé. Retourner l’appareil au centre de

service Krups agréé le plus près pour qu’il soit examiné, réparé

ou ajusté (voir la garantie limitée).

7- L’utilisation d’un accessoire non conçu pour cet appareil peut

causer des blessures.

8- Ne pas utiliser à l’extérieur.

9- Ne pas laisser pendre d’une surface horizontale ou s’assurer que

l’appareil ne touche pas des surfaces chaudes.

10- Ne pas placer sur ou à proximité d’un élément chauffant électri-

que ou à gaz ni dans un four chaud.

11- Pour débrancher, tourner tous les sélecteurs en position « OFF »,

puis débrancher le cordon de la prise murale.

12- Ne pas utiliser l’appareil à d’autres fins que celle pour laquelle il

est conçu.

13- Ne pas dévisser ou retirer le couvercle de sécurité du chauffe-

eau pendant que l’appareil est en marche. Attendre que le cycle

soit terminé et que toute l’eau et la vapeur soient utilisées. Ne

Français

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5219

retirer le couvercle de sécurité qu’après s’être assuré que la

pression a été libérée par la buse à vapeur.

• Appareil avec carafe en verre.

A. La carafe est conçue pour être utilisée uniquement avec cet

appareil. Elle ne doit jamais être utilisée sur une cuisinière.

B. Ne pas déposer une carafe chaude sur une surface froide ou

mouillée.

C. Ne pas utiliser une carafe fêlée ou une carafe dont la poignée

n’est pas solide.

D. Ne pas nettoyer la carafe à l’aide de nettoyants, de laine

d’acier ou d’autres outils abrasifs.

CONSERVER CES DIRECTIVES

DIRECTIVES SPÉCIALES SUR

LE CORDON D’ALIMENTATION

A. Le fil électrique est court, de façon à réduire les risques de bles-

sures qui pourraient survenir si l’on s’emmêle ou si l’on trébuche

sur un cordon plus long.

B. Si une rallonge est utilisée, faire preuve de prudence.

C. Si une rallonge est utilisée, (1) le calibre de la rallonge doit être

au minimum le même que celui de l’appareil, (2) si l’appareil est

muni d’une mise à la terre, la rallonge doit également être munie

d’une mise à la terre, et (3) la rallonge doit être placée hors de la

portée des enfants et de façon à ne pas faire trébucher quel-

qu’un.

D. Cet appareil est doté d’une fiche polarisée (une lame est plus

large que l’autre). Afin de réduire le risque de choc électrique,

cette fiche se branche d’une seule position. Si elle n’entre pas au

complet dans la prise de courant, tournez-la. Si elle n’entre

toujours pas, appelez un électricien qualifié. N’essayez pas de

modifier la prise d’aucune façon.

XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5220

La page charge ...

Krups XP1500US Manuel utilisateur

Marque: Krups

Modèle: XP1500US

Catégorie: Cafetières

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Krups XP1500US User manual
español: Krups XP1500US Manual de usuario

Krups XP1500US Manuel utilisateur

Krups XP1500US Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents