Caloric GTW21B2W Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

Top Freezer
Refrigerator
Owner’s Manual
English ......................................................................2
Français .................................................................. 16
Sección de castellano .............................................. 31
Keep these instructions for future reference. Be sure this
manual stays with refrigerator
2
Contents
Electrical Requirements .............................................2
Model Identification ....................................................3
Installation Instructions...............................................4
Installation Checklist ..................................................5
Controls
Refrigerator and Freezer Controls ............................6
Setting Controls ......................................................6
Exterior Moisture Control.........................................6
Refrigerator Features
Refrigerator Shelves ................................................7
Deli Drawer System (Some models) ........................7
Crisper Drawers (Some models) ..............................7
Covered Storage Bucket (Some models)..................8
Dairy Center (Some models) ...................................8
Door Shelves ..........................................................8
Freezer Features
Wire Shelf ..............................................................9
Care and Cleaning
General ..................................................................9
Odor Removal .........................................................9
Adhesives............................................................. 10
Door Gaskets ....................................................... 10
Condenser Coils ................................................... 10
Glass Shelves ...................................................... 10
Light Bulbs ........................................................... 10
Energy Tips ............................................................. 11
Vacation Tips ........................................................... 11
Normal Operating Sounds ........................................ 12
Before Calling For Service ........................................ 13
Factory Service Centers ........................................... 14
Asure Service Plan ................................................ 14
Warranty ................................................................. 15
Electrical Requirements
Recognize this symbol as a safety
precaution.
WARNING
Electrical Grounding Instructions -- This
refrigerator is equipped with a three-prong
(grounding) plug for protection against possible
shock hazards. If a two-prong wall receptacle is
encountered, contact a qualified electrician and
have the two-prong wall receptacle replaced
with a properly grounded three-prong wall
receptacle in accordance with the National
Electrical Code.
Refrigerator is designed to operate on a
separate 103 to 126 volt, 15 amp., 60 cycle
line.
Do not under any circumstances cut or
remove the round grounding prong from
the plug. Refrigerator must be grounded
at all times. Do not remove warning tag
from power cord.
WARNING
Do not use a two-prong adapter.
Do not use an extension cord.
3
Model Identification
Thank you for purchasing this Caloric® refrigerator. Please
read this Owner's Manual thoroughly. This manual
provides proper maintenance information. Any questions,
call the Consumer Affairs Department at 1-800-843-0304
inside U.S.A. and 1-319-622-5511 outside U.S.A.
Complete registration card and promptly return. If
registration card is missing, call the Consumer Affairs
Department.
When contacting Amana provide product information.
Product information is on the serial plate, located on
(upper left corner, ceiling) of refrigerator section. Record
the following information:
Model Number:
Manufacturing Number:
S/N or Serial Number:
Date of purchase:
Dealer’s name and address:
Keep a copy of sales receipt for future reference.
Amana also has a network of independent authorized
technicians. Locate a Factory Service Center or
independent authorized Amana technician by calling 1-
800-628-5782 inside U.S.A. and 1-319-622-5511 outside
U.S.A. Warranty service must be performed by an
authorized Amana technician. Amana also recommends
contacting an authorized Amana technician if service is
required after warranty expires.
Amana offers a complete line of appliances: cooktops,
dishwashers, dryers, freezers, microwave ovens, ranges,
wall ovens, and washers. Amana also manufactures a
complete selection of high efficiency gas furnaces plus
both central and room air conditioners.
Enjoy this new Caloric® refrigerator.
4
Caution
To avoid property damage, protect flooring with
cardboard, rugs, or other protective material
when moving refrigerator. Verify stabilizing leg
is raised before moving refrigerator. Raise
stabilizing leg by turning counterclockwise.
g. Slide appliance cart under side of refrigerator. Wrap
refrigerator with blanket or pad. Thread cart strap
around refrigerator and tighten. Do not overtighten
strap. Move refrigerator in front of final location.
h. Reverse doors if necessary.
Installation Instructions
Proper installation will ensure this refrigerator operates
most efficiently. Amana cannot be responsible for
improper installation.
1. Remove and reverse doors if necessary.
a. Remove top hinge cover. Remove top hinge.
b. Remove freezer door.
c. Lift door closure off center hinge pin. Remove center
hinge pin.
d. Remove refrigerator door.
e. Remove center hinge bracket.
f. Remove toe grille and bottom hinge cover. Remove
bottom hinge.
i. Rehang doors by reversing steps a-f.
Use a penny at top to space door 3/4" (18 mm)
from cabinet.
Handle side of door should be approximately 1/8"
(3 mm) higher than hinge side.
2. Connect ice maker water supply line.
See instructions on rear of refrigerator cabinet.
3. Plug in power cord.
4. Move refrigerator into final location.
5. Level refrigerator.
a. Remove toe grille. Remove bottom hinge cover if
refrigerator has a stabilizing leg.
b. Turn roller adjustment screw to raise or lower
refrigerator cabinet. Front of refrigerator must be
1/4" (6 mm) higher than back.
c. Turn stabilizing leg (some models) clockwise until
firmly against floor.
6. Review “Installation Checklist” in
Owner’s Manual with consumer.
5/16" (8 mm) screws
Center
hinge
Bottom hinge
3/8" (9 mm) screws
Phillips
screws
Top hinge
Center hinge
pin
3/4" (18 mm)
1/8" (3 mm)
Roller
adjustment
screw
Stabilizing leg (some models)
Bottom
hinge cover
5
Installation Checklist
This checklist is for personal records only.
Consumer Installer Doors
Handles are solidly attached to doors.
Handle side of door is 1/8" (3 mm) higher than hinge side. (Door lowers when
loaded with food.)
Doors seal completely to refrigerator cabinet.
Leveling
Refrigerator is tilted 1/4" (6 mm) from front to rear.
Toe grille is properly attached to refrigerator. Toe grille fits only one way.
Product Literature
Owner's manual is reviewed including the following information.
product registration card
Refrigerator and Freezer controls
Deli Drawer system
Crisper Drawers
normal operating sounds
Notes
Consumer's Signature DateInstaller's Company Name/Phone Number
Installer's Signature
6
Controls
This refrigerator operates at household temperatures of
55° to 110°F (13° to 43°C).
Exterior Moisture Control
Exterior Mositure Control is located on center divider
between refrigerator and freezer sections.
In humid conditions, refrigerators form condensation
around doors. Special heaters in refrigerator cabinet
minimize condensation.
Humidity depends on location of refrigerator. Set control to
ON if refrigerator is in a humid area or whenever moisture
is evident around doors. Set control to OFF if refrigerator
is in a less humid area. Setting can be adjusted as
conditions change.
High quality steel is used in this refrigerator. However,
constant exposure to moisture may cause refrigerator
cabinet to rust. Set control to ON anytime condensation
forms on refrigerator cabinet.
Setting Controls
Set controls precisely with a household thermometer that
includes temperatures between -5° to 50°F
(-21° to 10°C).
Put thermometer snugly between frozen packages in
freezer section. Wait 5-8 hours. If freezer temperature is
not 0° to 2°F (-17° to -16°C), adjust control, 1 number at a
time. Check again after 5-8 hours.
Put thermometer in a glass of water in middle of
refrigerator section. Wait 5-8 hours. If refrigerator
temperature is not 38° to 40°F (3° to 4°C), adjust control,
1 number at a time. Check again after 5-8 hours.
Refrigerator and Freezer Controls
Refrigerator and freezer controls are located on center
divider between refrigerator and freezer sections.
When freezer control is set to OFF, neither refrigerator nor
freezer sections will cool. Initially, set both controls to 4.
Wait 24 hours for refrigerator and freezer sections to
reach desired temperatures. After 24 hours, adjust
controls, one number at a time, as desired. 1 is warmest
setting and 7 is coldest.
7
Refrigerator Features
Caution
To avoid property damage, confirm shelf
is secure before placing items on shelf.
Refrigerator Shelves
Models feature either glass or wire shelves. Shelves
adjust to meet individual storage needs.
Caution
To avoid personal injury or property
damage, handle tempered glass shelves
carefully. Shelves may break suddenly if
nicked, scratched, or exposed to sudden
temperature change.
Remove shelves by lifting front, releasing hooks
from metal track then pulling out.
Replace shelves by inserting hooks into metal track
and lowering front.
Crisper Drawers (Some models)
Crispers keep produce fresh longer. Wrap produce tightly.
Do not wash produce before placing in crispers. Excess
moisture could cause produce to spoil prematurely. Do
not line crispers with paper towels. Paper towels will
retain moisture.
Crisper control is located below front shelf trim. Control
adjusts humidity in crispers. Standard drawers are
permanently set at high humidity. Slide control to high for
produce with leaves such as lettuce, spinach or cabbage.
Slide control to low for produce with skins such as
3. Remove left* crisper by lifting front while supporting
underneath then pulling out. *For doors hinged on left,
remove right crisper.
4. Remove support post at recess in bottom center of
Fresh Food section.
5. Remove other crisper by sliding to opposite wall. Lift
front while supporting underneath then pull out.
6. Replace crispers and shelf by reversing steps 1-5.
cauliflower, corn or tomatoes.
Remove shelf and crispers by completing the following
steps.
1. Open left* crisper. *For doors hinged on left, open
right crisper.
Caution
To avoid personal injury or property damage,
handle tempered glass shelves carefully.
Shelves may break suddenly if nicked,
scratched, or exposed to sudden temperature
change.
2. Remove shelf by gently pushing up from underneath.
Tilt one end up then pull out.
Push
Shelf
Up
Crisper
Shelf
Deli Drawer (Some models)
Remove drawer by lifting and pulling out. Remove
shelf by lifting front, releasing hooks from metal track
then pulling out.
Replace shelf by inserting hooks into metal track and
lowering front. Replace drawer by sliding in.
8
Covered Storage Bucket (Some models)
Storage bucket has a lid and removable egg tray. When
tray is removed, bucket will accept items such as a
standard egg carton, ice, etc.
Tapa
Bandeja para
huevos
Recipiente
para
almacenamiento
Dairy Center (Some models)
Dairy center provides convenient storage for items such
as butter, cheese, etc.
Remove dairy center by lifting door, pushing tabs
toward center and pulling out.
Replace dairy center by sliding in until tabs lock into
place and lowering door.
Dairy
Center
Door Shelves
Remove door shelves by lifting ends and pulling out.
Replace door shelves by placing shelf on glides and
sliding down.
Door
Shelf
9
Freezer Features
Caution
To avoid property damage, confirm shelf
is secure before placing items on shelf.
Wire Shelf
Remove wire shelf by tilting one end up and
pulling out.
Replace wire shelf by tilting one end up and placing
end on ledge. Tilt other end down and place on ledge.
Care and Cleaning
WARNING
To avoid electrical shock which can cause
severe personal injury or death, disconnect
power to refrigerator before cleaning. After
cleaning, connect power.
Caution
To avoid personal injury or property damage,
read and follow all cleaning product
manufacturer's directions.
General
1. Wash surfaces with 4 tablespoons baking soda
dissolved in 1 quart warm water and a soft, clean
cloth.
2. Rinse surfaces with warm water. Dry surfaces with a
soft, clean cloth.
Do not use the following items:
-abrasive or harsh cleaners, ammonia, chlorine
bleach, etc.
-concentrated detergents or solvents
-metal scouring pads
These items can scratch, crack and discolor
surfaces.
Do not place buckets, shelves, etc. in dishwasher.
Odor Removal
1. Remove all food and disconnect power to refrigerator.
2. Clean all interior surfaces including ceiling, floor, and
walls according to “General” instructions. Pay special
attention to corners, crevices, and grooves. Include all
drawers, shelves, and gaskets.
3. Connect power to refrigerator and return food to
refrigerator. Wash and dry all bottles, containers and
jars. Wrap foods in tightly sealed containers to
prevent further odor. After 24 hours, check if odor was
eliminated.
Complete the following steps if odor was not eliminated.
4. Complete steps 1-2.
5. Place garden fresh crispers on top shelf of Fresh
Food section. Pack refrigerator and freezer sections
including doors with crumpled sheets of black and
white newspaper.
6. Place charcoal briquettes randomly throughout
newspaper.
7. Close doors and let stand 24-48 hours.
8. Remove charcoal briquettes and newspapers.
9. Complete steps 2-3.
Contact Consumer Affairs Department if odor was still not
eliminated. Call 1-800-628-5782 inside U.S.A. and
1-319-622-5511 outside U.S.A.
10
Adhesives
1. Remove glue residue by rubbing toothpaste into
adhesive with fingers until adhesive loosens.
2. Rinse surface with warm water. Dry surface with a
soft, clean cloth.
Door Gaskets
1. Clean door gaskets every 3 months according to
“General” instructions.
2. Apply a light film of petroleum jelly to keep gaskets
pliable.
Condenser Coils
Clean condenser coil every 3 months to ensure maximum
performance of refrigerator. Accumulated dust and lint
may cause the following:
reduced cooling performance
increased energy usage
premature part failure
1. Remove toe grille by holding ends and pulling forward.
2. Clean front surface of condenser coil with a vacuum
cleaner hose nozzle.
3. Replace toe grille by inserting clips in holes and
snapping in.
Caution
To avoid property damage, protect soft vinyl or
other flooring with cardboard, rugs, or other
protective material. Verify stabilizing leg is
raised before moving refrigerator. Raise
stabilizing leg by turning counterclockwise.
4. Pull refrigerator away from wall. Run a vacuum
brush across condenser fan outlet grille on back
of refrigerator.
Glass Shelves
Caution
To avoid personal injury or property damage,
handle tempered glass shelves carefully.
Shelves may break suddenly if nicked,
scratched, or exposed to sudden temperature
change.
Remove shelf by lifting front, releasing hooks from metal
track then pulling out. Place shelf on a towel. Allow shelf
to adjust to room temperature before cleaning.
Clean crevices by completing the following steps:
1. Dilute mild detergent and brush solution into crevices
using a plastic bristle brush. Let set for 5 minutes.
2. Spray warm water into crevices using faucet spray
attachment.
3. Dry shelf thoroughly and replace shelf by inserting
hooks into metal track and lowering front.
Light Bulbs
WARNING
To avoid electrical shock which can cause
severe personal injury or death, disconnect
power to refrigerator before replacing light bulb.
After replacing light bulb, connect power.
Caution
To avoid personal injury or property
damage, observe the following:
Allow light bulb to cool.
Wear gloves when replacing light bulb.
Remove light bulb cover by removing screw at back
center. Pull cover down. Replace bulb(s) with 40-watt
appliance bulb(s).
Replace light bulb cover by placing cover over light
bulb. Insert and tighten screw.
1/4" hex
head
11
Energy Tips
This refrigerator is designed to be one of the most energy
efficient refrigerators available. Reduce energy use by
observing the following.
Operate in normal household temperatures of 55° to
110°F (13° to 43°C) away from heat sources and
direct sunlight.
Set refrigerator, and freezer controls no colder than
necessary.
Keep freezer section full.
Keep door gaskets clean and pliable. Replace
gaskets if worn.
Keep condenser coils clean.
Turn exterior moisture control ON when necessary.
Vacation Tips
Complete the following steps for short vacations.
1. Remove perishable foods. Warranty does not cover
food loss. Check warranty certificate for specific
coverage.
2. If an ice maker is installed, move ice maker arm to off
position.
Complete the following steps for long vacations.
1. Empty Refrigerator and Freezer sections.
2. Unplug refrigerator.
3. Clean refrigerator and door gaskets according to
“General” instructions in “Care and Cleaning” section.
4. Prop doors open, so air can circulate inside.
5. If an ice maker is installed, turn water supply to
refrigerator off and move ice maker arm to off
position.
12
Normal Operating Sounds
This new refrigerator may be replacing a differently
designed, less efficient or smaller refrigerator. Today’s
refrigerators have new features and are more energy
efficient. As a result, certain sounds may be unfamiliar.
These sounds are normal and will soon become familiar.
These sounds also indicate refrigerator is operating and
performing as designed.
1. Freezer fan air rushes and whirs.
2. Sealed system (evaporator and heat exchanger)
refrigerant flow gurgles, pops or sounds like boiling
water.
3. Condenser fan air rushes and whirs.
4. Compressor has a high pitched hum or pulsating
sound.
5. Defrost timer sounds like an electric clock and
snaps in and out of defrost cycle.
6. Freezer control clicks when starting or stopping
compressor.
7. Defrost heater sizzles, hisses or pops.
8. Ice cubes from ice maker (some models) drop into
ice bucket.
Water valve (some models) buzzes when ice maker
fills with water. This occurs whether or not refrigerator
is connected to water supply. If refrigerator is not
connected to water supply, stop sound by raising ice
maker arm to off position. (Not shown)
Foam insulation is very energy efficient and has
excellent insulating capabilities. However, foam
insulation is not as sound absorbent as
previously used fiberglass insulation. (Not shown)
13
Before Calling For Service
Refrigerator does not operate.
Confirm freezer control is on.
Confirm refrigerator is plugged in.
Check fuse or circuit breaker. Plug in another item at
that wall outlet.
Wait 40 minutes to see if refrigerator restarts. If
freezer control is on, lights work but 2 fans and
compressor are not operating, refrigerator may be in
defrost cycle.
Refrigerator still won’t operate.
Unplug refrigerator. Transfer food to another unit
or place dry ice in freezer section to preserve food.
Warranty does not cover food loss. Check
warranty certificate for specific coverage.
Call 1-800-628-5782 inside U.S.A. and
1-319-622-5511 outside U.S.A. to locate an
authorized Amana technician.
Food temperature appears too warm.
See above sections.
Allow time for recently added warm food to reach
refrigerator or freezer temperature.
Check gaskets for proper seal.
Clean condenser coils.
Adjust refrigerator and/or freezer control.
Confirm rear air grille is not blocked. Rear air grille is
located behind left crisper.
Food temperature is too cold.
Clean condenser coils.
Adjust refrigerator control.
Adjust freezer control to warmer setting. Allow several
hours for temperature to adjust.
Refrigerator runs too frequently.
It may be normal to maintain constant temperature.
Doors may have been opened frequently or for an
extended period of time.
Allow time for recently added warm food to reach
refrigerator or freezer temperature.
Clean condenser coils.
Adjust freezer control.
Check gaskets for proper seal.
Water droplets form on inside of refrigerator.
It is normal during high humidity periods or if doors
have been opened frequently.
Water droplets form on outside of refrigerator.
Check door gaskets for proper seal.
Turn exterior moisture control switch ON.
Crispers or deli drawer system does not close freely.
Check for a package which may prevent drawer
from closing properly.
Confirm drawer is in proper position.
Clean drawer channels with warm, soapy water.
Rinse and dry thoroughly.
Apply a thin layer of petroleum jelly to drawer
channels.
Confirm refrigerator is level.
Refrigerator has an odor.
See “Odor Removal” instructions in “Care and
Cleaning” section.
Refrigerator or ice maker make unfamiliar sounds or
seems too loud.
It may be normal. See “Normal Operating Sounds”
section.
Ice cubes have an odor.
See “Odor Removal” instructions in “Care and
Cleaning” section.
Discard ice and clean ice bucket or trays more
frequently. Ice cubes are porous and absorb odors
easily.
Ice cubes stick together or ‘shrink’.
Empty ice cube bucket or trays more frequently. If
used infrequently, ice cubes may stick together or
shrink.
14
Factory Service Centers
Listed below are Factory Service Centers which service
most metropolitan and surrounding areas. Amana also
has a network of independent authorized technicians.
Locate a Factory Service Center or independent
authorized Amana technician by calling 1-800-628-5782
inside U.S.A. and 1-319-622-5511 outside U.S.A. When
contacting Amana provide product information. Product
information is on the serial plate, located on (upper left
corner, ceiling) of Fresh Food section. Warranty service
must be performed by an authorized Amana technician.
Amana also recommends contacting an authorized
Amana technician if service is required after warranty
expires.
Amana Factory Service Center Arizona
Also dispatches service in areas of Nevada
Amana Factory Service Center California
Also dispatches service in areas of Washington and
Oregon
Amana Factory Service Center Colorado
Also dispatches service in areas of Utah
Amana Factory Service Center Florida
Amana Factory Service Center Georgia
Also dispatches service in areas of Alabama, North
Carolina, South Carolina, and Tennessee
Amana Factory Service Center Iowa
Also dispatches service in areas of Kansas,
Minnesota, Missouri, and Wisconsin
Amana Factory Service Center Illinois
Also dispatches service in areas of Indiana and
Kentucky
Amana Factory Service Center Massachusetts
Also dispatches service in areas of New Hampshire
and Rhode Island
Amana Factory Service Center Maryland
Also dispatches service in areas of Pennsylvania,
Virginia, and Washington D.C.
Amana Factory Service Center New York
Also dispatches service in areas of Connecticut and
New Jersey
Amana Factory Service Center Ohio
Also dispatches service in areas of Michigan and
Pennsylvania
Amana Factory Service Center Texas
Asure Service Plan
Amana is pleased to offer long-term service protection on
this new refrigerator. AsureExtended Service Plan is
specially designed to supplement Amana's strong
warranty. Asure provides budget-protecting coverage on
refrigerator for up to 5 full years and includes parts, labor
and travel charges. A participating Amana dealer has
details.
15
Warranty
Full One Year Warranty
Full Five Year Warranty on Sealed System Components
and Food Compartment Liner
First Year
Raytheon Appliances will repair or replace, free of charge, any part which is defective due to workmanship or
materials.
Second through Fifth Year
Raytheon Appliances will replace, free of charge, any sealed system component (compressor, condenser,
evaporator and interconnecting tubing) and repair any food compartment liner (exclusive of door liner) which
is defective due to workmanship or materials.
Warranty Limitations
Begins at date of original purchase.
Applies to product used within the United States
or in Canada if product has Canadian Standards
Association listing when shipped from the factory.
Service must be performed by an authorized
Amana technician.
Warranty Is Void If
Serial plate is defaced.
Product is used on a commercial, rental or leased
basis.
Product has defect or damage due to product
accident, alteration, connection to an improper
electrical supply, fire, flood, lightning, shipping and
handling, or other conditions beyond the control of
Raytheon Appliances.
Product is improperly installed or used.
Owner's Responsibilities
Provide proof of purchase (sales receipt).
Provide normal care and maintenance. Replace
owner replaceable items where directions appear
in Owner's Manual.
Make product reasonably accessible for service.
Pay premium service costs for service outside
technician's normal business hours.
Pay for service calls related to product installation
or usage.
In no event shall Raytheon Appliances be liable
for incidental or consequential damages
including food loss*
*This warranty gives you specific legal rights and you
may have others which vary from state to state. For
example, some states do not allow the exclusion or
limitation of incidental or consequential damages so
this exclusion may not apply to you.
16
Normes électriques
Ce symbole indique une mesure de
sécurité
MISE EN GARDE
Instructions de mise à la terre - Ce réfrigérateur
est muni d’une fiche à 3 broches pour prévenir
le risque d’électrocution. Si une prise de
courant à deux broches est présente, contacter
un électricien qualifié et la faire remplacer par
une prise de courant à trois broches
correctement mise à la terre, conformément
aux normes du Code national de l’électricité.
Le réfrigérateur est conçu pour fonctionner sur
une ligne séparée de 60 Hz, 15 ampères, de
103 à 126 volts.
Ne jamais couper ou enlever la broche
ronde de mise à la terre de la fiche. Le
réfrigérateur doit être mis à la terre en tout
temps. Ne jamais enlever l’étiquette
d’avertissement du cordon d’alimentation.
AVERTISSEMENT
Ne jamais utiliser d’adaptateur à deux
broches.
Ne jamais utiliser de rallonge.
Normes électriques .................................................. 16
Identification de modèle ............................................ 17
Instructions d’installation .......................................... 18
Liste de vérification de l’installation ........................... 19
Contrôles
Commandes Congélateur et Réfrigérateur .............. 20
Réglages des commandes .................................... 20
Contrôle de l’humidité extérieure............................ 20
Caractéristiques Réfrigérateur
Clayettes Réfrigérateur.......................................... 21
Tiroir à charcuterie (Certains modèles)................... 21
Bacs à légumes (Certains modèles) ...................... 21
Bac utilitaire avec couvercle (Certains modèles) ..... 22
Casier laitier ......................................................... 22
Clayettes de porte ................................................ 22
Caractéristiques Congélateur
Étagère métallique (Certains modèles)................... 23
Entretien et Nettoyage
Général ................................................................ 23
Suppression des odeurs........................................ 23
Adhésifs ............................................................... 24
Joints de porte ...................................................... 24
Bobine de condensateur........................................ 24
Clayettes de verre ................................................. 24
Ampoules Electriques ........................................... 25
Conseils de conservation de l’énergie ....................... 25
Conseils pour les Vacances ..................................... 26
Bruits de Fonctionnement Normaux.......................... 27
Avant d’appeler le Technicien.................................... 28
Centres de service Agréés........................................ 29
Programme d’entretien Asure™................................ 29
Garantie .................................................................. 30
Table des matières
17
Identification du Modèle
Merci d’avoir fait l’achat d’un réfrigérateur Caloric®.
Veuillez lire attentivement le manuel du propriétaire. Ce
manuel renferme des renseignements sur l’entretien de
l’appareil. Pout toute question, appeler le service à la
clientèle au 1-800-843-0304 aux États-Unis et le 1-319-
622-5511 de l’extérieur des États-Unis.
Remplir la carte d’enregistrement et la renvoyer
promptement. S’il n’y a pas de carte d’enregistrement,
appeler le service à la clientèle.
Lorsque vous communiquez avec Amana, veuillez fournir
les renseignements concernant l’appareil. Ces
renseignements apparaissent sur la plaque du numéro de
série située dans le coin gauche supérieur du
compartiment Réfrigérateur. Veuillez noter les
renseignements suivants :
Numéro de modèle :
Numéro de fabrication :
Numéro de série :
Date d’achat :
Nom et adresse du marchand :
Veuillez conserver une copie de la facture pour
référence future.
Amana possède également un réseau de techniciens
indépendants agréés. Appeler le 1-800-628-5782 aux
États-Unis ou le 1-319-622-5511 de l’extérieur des États-
Unis pour connaître le centre de service ou technicien
indépendant agréé par Amana le plus près de chez vous.
Les réparations sous garantie doivent être effectuées par
un technicien agréé par Amana. Amana recommande
également de contacter un technicien agréé par Amana
si l’appareil nécessite une réparation suite à l’expiration
de la garantie.
Amana offre une gamme complète d’appareils ménagers:
surfaces de cuisson, lave-vaisselle, sécheuses,
congélateurs, fours à micro-ondes, cuisinières, fours
encastrés et machines à laver. Amana fabrique également
une vaste sélection de fourneaux à gaz et d’appareils de
climatisation centrale et individuelle.
Nous espérons que vous apprécierez ce nouveau
réfrigérateur Caloric®.
18
MISE EN GARDE
Pour éviter tout risque d’électrocution pouvant
causer des blessures graves voire mortelles,
débrancher le réfrigérateur avant d’enlever les
portes. Après avoir replacé les portes, brancher
de nouveau l’appareil.
a. Enlever le couvercle de la charnière supérieure.
Enlever la charnière supérieure.
b Enlever la porte du réfrigérateur.
c. Enlever l’axe de charnière centrale.
d. Enlever la porte du congélateur. Une tige de support
interne peut glisser hors de la douille de la charnière.
Replacer la tige avant de poser la porte.
e. Enlever le support de charnière centrale.
f. Enlever la grille et le couvercle de la charnière
inférieure. Enlever la charnière inférieure.
Vis 5/16 po (8 mm)
Axe de charnière centrale
Charnière inférieure
Vis Phillips
Vis 3/8 po (9 mm)
Charnière centrale
Charnière supérieure
Instructions d’Installation
Une installation adéquate assurera le fonctionnement
efficace de ce réfrigérateur. Amana Refrigeration, Inc. ne
peut être tenue responsable en cas d’installation
inadéquate.
1. Enlever et inverser les portes si nécessaire.
Attention
Pour éviter tous dégâts matériels, recouvrir les
planchers en vinyle ou autre type de plancher
avec du carton, des tapis ou autre matériel de
protection avant de déplacer le réfrigérateur.
g. Glisser le chariot servant à transporter l’appareil sous
le côté du réfrigérateur. Recouvrir le réfrigérateur avec
un coussin ou une couverture. Enfiler la courroie du
chariot autour du réfrigérateur et serrer. Ne pas trop
serrer la courroie. Déplacer le réfrigérateur devant
l’endroit désiré.
h. Inverser les portes si nécessaire.
Le logo de la plaque du fabricant s’inversera
automatiquement.
Replacer la tige de support interne sur le côté
charnière de la porte du congélateur avant de
poser la porte.
i. Replacer les portes en procédant à l’inverse des étapes
a-f.
Utiliser une pièce d’un sou sur le dessus des
portes pour créer un espace de 3/4" (18 mm) entre
la porte et l’appareil.
Le côté de la porte où se situe la poignée doit être
1/8" (3 mm) plus élevé que le côté de la charnière.
1/8" (3 mm)
3/4" (18 mm)
2.Raccorder l’appareil à glaçons au tuyau
d’alimentation en eau.
Voir les instructions à l’arrière du réfrigérateur.
3. Brancher le cordon d’alimentation.
4. Déplacer le réfrigérateur à l’endroit désiré.
5. Mettre le réfrigérateur de niveau.
a. Enlever la grille. Enlever le couvercle de la charnière
inférieure si le réfrigérateur est muni d’un pied de
stabilisation.
b. Tourner la vis de réglage du rouleau pour élever ou
abaisser le réfrigérateur. L’avant du réfrigérateur doit
être 1/4" (6 mm) plus élevé que l’arrière.
c. Tourner le pied de stabilisation (disponible sur certains
modèles) dans le sens horaire jusqu’à ce qu’il repose
fermement sur le plancher.
Couvercle de
la charnière
inférieure
Vis de réglage
du rouleau
Pied de stabilisation (certains modèles)
6. Examiner avec le propriétaire la “liste de contrôle
d’installation” dans le manuel d’installation.
19
Liste de Contrôle d’Installation
Cette liste de contrôle d’installation est présentée pour usage personnel seulement.
Client Installateur
Portes
Les poignées sont solidement fixées aux portes.
Le côté de la poignée de porte est 1/8 po (3 mm) plus élevé que le côté de la charnière de la
porte. (La porte s’abaisse lorsqu’elle est remplie de nourriture.)
Les portes sont bien scellées au meuble du réfrigérateur.
Mise à niveau
Le réfrigérateur est incliné de 1/4" (6 mm) de l’avant vers l’arrière.
La grille est bien fixée au réfrigérateur.
Documentation concernant le produit
Le manuel du propriétaire doit comprendre les renseignements suivants :
- carte d’enregistrement de l’appareil
- commandes réfrigérateur et congélateur
- système Tiroir à charcuterie
- bacs à légumes
- bruits de fonctionnement normaux
Notes
Date
Nom de l’entreprise de l’installateur/
Numéro de téléphone
Signature de l’installateur
Signature du client
20
Commandes
Ce réfrigérateur fonctionne de façon plus efficace lorsque
la température ambiante se situe entre 55o et 110 oF (13
oC à 43 oC).
Commandes du Réfrigérateur et du
Congélateur
Les commandes du réfrigérateur et du congélateur sont
situées sur la cloison centrale séparant ces deux parties.
Lorsque la commande congélateur est en position OFF
(ARRÊT), ni l’un ni l’autre des compartiments
Réfrigérateur ou congélateur ne refroidiront. Au départ,
régler ces deux commandes sur 4. Attendre 24 heures
avant que les compartiments réfrigérateur et congélateur
n’aient atteint les températures désirées. Après 24
heures, régler les commandes sur les valeurs désirées,
un chiffre à la fois. Le réglage le plus chaud est 1, tandis
que 7 est le réglage le plus froid.
Réglage des commandes
Régler les commandes avec précision à l’aide d’un
thermomètre domestique dont les températures se situent
entre -5o et 50 oF (-21o et 10 oC).
Placer le thermomètre entre les emballages congelés
dans le compartiment Congélateur. Attendre 5 à 8 heures.
Si la température congélateur ne se situe pas entre 0o et
2 oF (-17o et -16 oC), régler la commande, un chiffre à la
fois. Vérifier de nouveau après 5 à 8 heures.
Placer le thermomètre dans un verre d’eau au milieu du
compartiment réfrigérateur. Attendre 5 à 8 heures. Si la
température du compartiment Réfrigérateur ne se situe
pas entre 38o et 40 oF (3o et 4 oC), régler la commande,
un chiffre à la fois. Vérifier de nouveau après 5 à 8 heures.
Contrôle de l’humidité extérieure
Le contrôle de l’humidité extérieure se situe sur le
séparateur central entre les sections réfrigérateur et
congélateur.
Dans des conditions humides, le réfrigérateur produit de
la condensation autour des portes. Un appareil de
chauffage spécial dans le meuble du réfrigérateur
minimise la condensation.
L’humidité dépend de l’emplacement du réfrigérateur.
Réglez le contrôle à ON (Marche) si le réfrigérateur est
situé dans un endroit humide ou lorsqu’il y a des traces
d’humidité autour des portes. Réglez le contrôle à OFF
(Arrêt) si le réfrigérateur est situé dans un endroit moins
humide. Les réglages peuvent être modifiés selon les
conditions.
De l’acier de qualité supérieure est utilisé dans la
fabrication de ce réfrigérateur. Cependant, une exposition
constante à l’humidité peut provoquer la corrosion du
meuble du réfrigérateur. Réglez le contrôle sur la position
ON (Marche) dès que de la condensation se forme sur le
meuble du réfrigérateur.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46

Caloric GTW21B2W Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues