Powerfist 8913212 Le manuel du propriétaire

V1.1 8913212

Please read and understand all instructions before use. Retain this manual for future

reference.

8913212 Gas Pressure Washer V1.1

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Max. Pressure Rating 3,200 PSI

Max. Flow Rate 2.5 GPM

Engine Displacement 212cc

Theoretical Horsepower 6-1/2 HP

Engine Type Ducar

Fuel Capacity 1.45 gal.

Fuel Type Gasoline

Start Type Recoil

Low Oil Shut Down Yes

Pump Type Axial, Maintenance-Free

Pump Capacity 0.084 quarts (0.08 litres)

Pump Oil 85W-90

Unloader Valve Type Non-Adjustable

Chemical Injector Type Downstream non-adjustable

Nozzle Spray Angle Soap, 0°, 15°, 25°, 40°

Nozzle Type Quick connect

Inlet Water Temperature Rating Max. 40°C (104°F)

Outlet Water Temperature Rating Max. 40°C (104°F)

Hose Size 30 ft

Hose Material PVC/Rubber

Cart Frame Material Steel Q195

Wheel Size 12 x 4 in.

Wheel Type Pneumatic

V1.1 Gas Pressure Washer 8913212

Visit www.princessauto.com for more information 3

INTRODUCTION

The Gas Pressure Washer has a 212cc engine that starts easily and runs

smoothly. The axial pump has a built-in thermal relief valve and unloader

valve. The chemical injector allows for the application of soaps and

degreasers.

A separate manual for the gasoline engine is included. Please read the

engine manual before using this product. The engine manual is considered

accurate when information about the engine disagrees with this manual.

SAFETY

WARNING! Read and understand all instructions before using this tool.

The operator must follow basic precautions to reduce the risk of

personal injury and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may

result in minor or moderate injury if proper practices are not

taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice

will result in equipment or property damage, but not personal

injury.

8913212 Gas Pressure Washer V1.1

4 For technical questions call 1-800-665-8685

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-

lit and free of distractions. Place lights so you are not working in a

shadow.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store tools properly in a safe and dry location. Keep tools out of the

reach of children.

4. Do not install or use in the presence of flammable gases, dust or

liquids.

5. Using a pressure washer can create puddles and slippery surfaces. The

work area should have adequate slopes and drainage to reduce the

possibility of falling due to slips.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the

Canadian Standards Association (CSA) or American National Standards

Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply with

CSA Z94.3-07 or ANSI Z87.1 standards based on the type of work

performed.

a. Use indirect vented safety goggles designed for wet conditions to

protect eyes from injury. Spray from this unit has extreme pressure

and can ricochet back splashing water or propelling objects towards

eyes.

2. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

3. Wear protective clothing designed for the work environment and tool.

4. Non-skid footwear is recommended to maintain footing and balance in

the work environment.

5. This tool can cause hearing damage. Wear hearing protection gear with

an appropriate Noise Reduction Rating to withstand the decibel levels.

V1.1 Gas Pressure Washer 8913212

Visit www.princessauto.com for more information 5

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to the tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating the tool. Proper footing and balance

enables better control in unexpected situations.

4. Securely hold this tool using both hands. Using a tool with only one

hand can result in loss of control.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific

function. Do not modify or alter this tool or use it for an unintended

purpose.

2. Do not use the tool if any parts are damaged, broken or misplaced.

Repair or replace the parts.

3. NEVER defeat the safety features of this product.

4. Keep pressure washer a minimum of four feet away from anything that

could be damaged by heat from the muffler exhaust such as houses,

automobiles, dry brush or live plants.

5. DO NOT leave the spray gun unattended while the unit is running.

6. Always operate the pressure washer from a stable surface. Avoid using the

pressure washer from precarious locations such as ladders or scaffolding.

7. DO NOT attempt to repair damaged or defective high-pressure hoses.

Always replace them.

8. DO NOT repair leaking connections with sealant of any kind. Replace the o-

ring or seal.

9. DO NOT disconnect the high-pressure hose from the pump and spray gun

while the system is pressurized.

10. Always ensure that the spray gun, nozzles, hoses and fittings are correctly

attached before starting the engine.

8913212 Gas Pressure Washer V1.1

6 For technical questions call 1-800-665-8685

11. NEVER hold onto the hose or fittings during operation. This can allow

pressurized water to escape and inflict an injury.

12. DO NOT plug this pressure water into a hot water supply. This pressure

washer is designed for cold water use only.

13. Prior to starting the pressure washer in cold weather, be sure ice has not

formed in any part of the equipment.

14. Ensure the pressure washer is not covered during operation to avoid

overheating the motor.

15. This pressure washer is capable of producing pressures up to 3,100 PSI. To

avoid property damage and personal injury, do not operate the pump with

components rated for less than 3,200 PSI working pressure.

16. If connecting the pressure washer to a portable water system, ensure the

water system is protected against backflow.

17. NEVER attach or remove wand or hose fittings while system is

pressurized.

18. Never transport or make adjustments to this unit while it is running.

19. Do not allow the high pressure hose to come in contact with any hot

part of the unit. The hose might be damaged, possibly causing it to

burst or leak under high pressure.

20. Shut off the pressure washer if it is leaking water. Discharge all

pressure before tightening fittings or having repair work done by a

qualified technician.

SPRAYING PRECAUTIONS

DANGER! The pressure washer produces fluid pressures and velocities

strong enough to penetrate human and animal flesh that will result in

serious injury or amputation with some nozzles.

DANGER! NEVER aim the pressure washer spray gun in the direction of

people or animals, even if the power and water supply are turned off. High

velocity fluid spray can cause objects to break, propelling particles at high

speeds.

1. Keep operating area clear of all persons, animals and obstacles.

2. DO NOT spray flammable or toxic liquids.

3. DO NOT spray near a power source.

4. DO NOT lock the spray gun in open position.

5. Only use a spray gun that has a trigger lock or trigger guard in place

V1.1 Gas Pressure Washer 8913212

Visit www.princessauto.com for more information 7

and in working order.

6. Be careful when squeezing the trigger, as recoil from the spray gun can

cause the operator to fall.

7. NEVER place hands in front of nozzle.

8. Always be certain spray gun, nozzles and accessories are correctly

attached.

9. Relieve system pressure after shutting off the engine and water supply

by aiming the spray gun in safe direction and squeezing the trigger

until water stops flowing.

10. Keep high pressure hose connected to pump and spray gun while

system is pressurized.

RISK OF CHEMICAL BURN

DANGER! Use of acids, toxic or corrosive chemicals, poisons, insecticides,

or any kind of flammable solvent with this product could result in

serious injury or death.

1. DO NOT use acids, gasoline, kerosene, or any other flammable materials

in this product. Use only household detergents, cleaners and

degreasers recommended for use in pressure washers.

2. Wear protective clothing to protect eyes and skin from contact with

sprayed materials.

3. DO NOT use chlorine bleach or any other corrosive compound.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a

malfunction and personal injury.

Remove the parts and accessories from the packaging and inspect for

damage. Make sure that all items in the contents are included.

Contents: • Pressure Washer • Quick-Connect Spray Nozzles (5)

• 30 ft Hose • Detergent Hose • Spray Gun • Spray Wand

ASSEMBLY & INSTALLATION

Numbered references in parenthesis (#1) refer to the included Parts List.

Dashed numbers in parenthesis (Fig. 1-1) refer to a specific point in an

illustration or image.

8913212 Gas Pressure Washer V1.1

8 For technical questions call 1-800-665-8685

1. Install the assembled

wheel’s axle (#9) into the

frame’s sleeve on the side

of the fuel tank (Fig. 1).

Align the wheel’s detent

pin with the sleeve hole.

Push the axle into the

sleeve until the pin pops

out. Repeat with the other wheel on the other side.

2. Slide the upper frame handle (#20) over the

two upright tubes on the frame (#3) and

press down until handle is seated and two

detent pins snap into place (Fig. 2).

3. Screw the wand (#30) onto the spray gun

(#31). Make sure the connection is tight (Fig. 3).

4. Insert the spray hose’s inlet coupler into

the spray gun handle and secure with

the threaded black nut (Fig. 4) Turn

clockwise until it is hand tight.

5. Attach the desired nozzle to the wand by

pulling back the quick connect collar and

pushing the nozzle onto the end of the Wand.

Make sure the quick connect collar locks the

nozzle in place (Fig. 5).

6. Insert the spray hose’s other end into the

pump’s high pressure outlet and secure with

the black nut until hand-tight (Fig. 6).

7. The engine does not ship with oil or gasoline.

Consult the Engine manual for preparation

instructions before using the tool.

OPERATION

Choose the nozzle that best meets the needs of the job. See chart below.

Only use the nozzles on surfaces capable of withstanding the force of the

spray.

Fig. 3

Fig. 5

Fig. 1

Fig. 2

Fig. 4

Fig. 6

V1.1 Gas Pressure Washer 8913212

Visit www.princessauto.com for more information 9

PRESSURE NOZZLE SELECTION

The pressure washer has five spray nozzles. Each nozzle is color coded and

delivers a specific spray arc between 0° and 65°. The narrower the degree

arc, the higher the pressure at the water spray’s point of contact with the

item being cleaned. Distance from the item that is being sprayed will also

factor into the pressure level at the point of contact.

The table identifies the colour, arc and an example. The purpose example is only

a suggestion as some items are made of multiple materials and not all materials

will withstand the force of the pressurized spray. Choose the nozzle with the

largest spray arc, if you are unsure how much pressure to apply to an item

without damaging it. Switch to a nozzle with a narrower degree angle until you

find the one that achieves the results you want.

The nozzles are stored on the panel mounted on the pressure washer’s handle.

Colors on the panel identify the correct nozzle location.

Colour Arc Purpose Example

Red 0° Narrow stream to clean

and remove embedded

grit or grime from

concrete or brick

surfaces.

Yellow 15° Heavy duty cleaning of

concrete surfaces or

without use of

chemicals.

Green 25° Clean wood surfaces

compacted dirt, paint,

oil or mildew. Also for

use with chemicals.

White 40° Clean delicate surfaces

like stucco or siding.

Also patio furniture or

home siding.

8913212 Gas Pressure Washer V1.1

10 For technical questions call 1-800-665-8685

ATTACH THE WATER HOSE

1. Attach the hose to a water spigot. The water hose muse be 10 ft or

longer with no other connections that will restrict or divert the water

flow.

2. Check the screen in the pump’s water inlet

valve and remove any debris.

3. Run water through hose to flush out debris,

before attaching the end to the inlet below the

high pressure hose (Fig. 7).

USING DETERGENT

IMPORTANT! Only use the Black (Soap) Nozzle when spraying detergents.

The power of the other nozzles will propel mist back at the operator and

can embed detergent into the surface.

1. Read the detergent’s directions. Only use detergents

specified for use with pressure washers.

2. Connect the Detergent Siphon Tube (#25) to the

nipple on the Pressure Hose connection area of the

Pump (Fig. 8).

3. Submerge siphon tube’s strainer end (#26) into

the container of prepared detergent solution.

4. Follow instructions to start the pressure washer.

STARTING THE PRESSURE WASHER

WARNING! The red trigger lock must be in place to prevent accidental

activation of the spray gun. Flip the red lever on the trigger up so it

rests in the depression in the handle. Aim the spray gun in a safe

direction and test the trigger to ensure the lock is working.

Black 65°

(Soap)

Wet surfaces or apply

chemicals/detergents.

Does not provide

enough force to clean

by itself.

Table 1

Fig. 7

Fig. 8

V1.1 Gas Pressure Washer 8913212

Visit www.princessauto.com for more information 11

NOTICE! DO NOT siphon standing water for the water supply. Particulate

matter can contaminate the pump. Use only clean, cold water (less than

100°F).

NOTICE! DO NOT run the pump without the water supply connected and

turned on. This may damage the pump mechanism beyond repair.

When the engine is running, do not allow the Pressure Washer to remain

idle for more than two minutes. If allowed to remain idle, the water in the

unit will heat up, possibly causing damage to the Pressure Washer.

During normal operation the thermal relief valve may release small amounts of

water intermittently.

1. Turn on the water spigot.

2. Squeeze the trigger for one minute to purge air from the system. Reset

the trigger guard.

3. Start the engine by following the instructions in the engine manual.

BREAK-IN PERIOD

Breaking-in the engine will help to ensure proper equipment and engine

operation. The operational break-in period will last about 3 hours of use.

During this period:

1. Do not apply a heavy load to the equipment.

2. Do not operate the engine at its maximum speed.

The maintenance break-in period will last about 20 hours of use. Change the

engine oil after this period.

USING THE PRESSURE WASHER

1. Unlock and hold down the trigger to start the stream. Be aware that

when it is first started, the gun will kick.

2. Start with a low pressure nozzle and gradually use higher pressures as

needed.

a. Test spray the surface at an edge to make sure that the stream is

not too strong.

b. If the stream damages the surface, move farther away to reduce

the applied pressure.

c. If the stream is still too strong, lock the trigger in the safety

position and change to a lower pressure nozzle.

8913212 Gas Pressure Washer V1.1

12 For technical questions call 1-800-665-8685

3. Hold the wand at about a 45° angle when cleaning; spraying the surface

directly could embed dirt into the surface (especially with the high

pressure nozzles). Spray at distance of about three to five feet.

4. Clean vertical and sloped surfaces from the top down.

5. When cleaning horizontal surfaces, occasionally use the stream to

clear the area of excess water.

6. Hold the Trigger down and move the wand back and forth slowly and

steadily to pressure wash the surface. Take special care when spraying

surfaces made of two different materials (brick and mortar, for

example), so as to not damage the softer of the two materials during

pressure washing.

7. If the surface is streaked or uneven at the end of a job, switch to a

Nozzle that has a wider spray pattern to blend the affected area.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier

to control and will have fewer problems.

2. Inspect the tool fittings, alignment, hoses and power supply cord

periodically. Have damaged or worn components repaired or replaced

by an authorized technician. Only use identical replacement parts

when servicing.

3. Follow instructions for lubricating and changing accessories.

4. Only use accessories intended for use with this tool.

5. Keep the tool clean, dry and free from oil/grease at all times.

6. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

AFTER EACH USE

CHECK HIGH PRESSURE HOSE

WARNING! NEVER repair the high pressure hose. Repairs can fail and will

be weaker than the hose itself. A hose that fails while under pressure

can inflict a serious injury. Replace with a hose that has a maximum

pressure rating that exceeds the pressure washer’s maximum output.

V1.1 Gas Pressure Washer 8913212

Visit www.princessauto.com for more information 13

The high pressure hose can develop leaks due to wear, kinking or misuse and

abuse. Inspect the hose each time before using it. Check the hose for cuts,

leaks, abrasions or bulging spots. Also check the couplings to ensure they are

not loose. Replace the hose immediately if any of these conditions exist.

CHECK SIPHON TUBE

Check the detergent siphoning tube for clogs, leaks or tears. Clean the tube of

clogs. Replace if damaged or it no longer fits the pump fitting tightly.

CHECK SPRAY GUN

Examine the hose connection to the spray gun and make sure it is secure. Check

that the trigger lock is in place to prevent accidental spraying. Replace the spray

gun immediately if the trigger lock is damaged or will not remain in place.

CHECK SPRAY WAND AND PRESSURE NOZZLES

A pulsing sensation felt when squeezing the trigger indicates either the

spray wand or the pressure nozzle is partially clogged and is causing

pressure to build in the pump.

1. Shut off the engine and turn off the water supply. Then release the

pressure in the pump system by aiming the spray gun in a safe

direction and squeezing the trigger.

2. Remove the spray nozzle from end of spray gun wand.

3. Use a small paper clip to free any foreign material clogging or

restricting the spray nozzle.

4. Disconnect the spray gun wand and check for foreign material that

may clog the tube.

5. Remove additional debris by back flushing water through the spray

gun wand using a garden hose.

6. Reinstall spray nozzle into spray gun wand.

7. Reconnect spray gun wand to spray gun.

8. Make sure the garden hose is connected to the pump’s water inlet.

Check that high pressure hose is connected to spray gun and pump.

Turn on the water.

9. Start engine following instructions Starting Your Pressure Washer

10. Test the pressure washer with each of the five spray nozzles to ensure

they are all unclogged.

8913212 Gas Pressure Washer V1.1

14 For technical questions call 1-800-665-8685

REPAIRING LEAKING CONNECTIONS

WARNING! Do not use thread-seal tape or liquid to prevent leaks in the

high pressure hose. This can cause a high pressure leak that can result

in a serious injury or injection injury.

1. Replace the o-rings of any connection that leaks.

2. Replace the connectors if the leaks continue.

EMPTY THE PUMP

Force water from the pump by pulling the recoil starter 6 times.

ENGINE MAINTENANCE

See the Engine manual for instructions on how to properly maintain the engine.

CLEANING

Use a damp cloth to wipe exterior surfaces clean. A soft bristle brush can

loosen caked on dirt, oil, etc. A vacuum cleaner will remove loose dirt and

debris in difficult to reach places.

Examine the screen on the pump water inlet. Clean it if the screen is

clogged or replace it if screen is damaged.

MAINTENANCE SCHEDULE

After Each Use Check and Clean Water Inlet screen

Check High Pressure Hose

Check and Clean Detergent Siphoning Tube

Check Spray Gun for Leaks

Clean Debris

Check Engine Oil Level before starting

Annually (50 hours of use) Check and Clean Air Filter

Check muffler and spark arrester

LUBRICATION

Inspect and lubricate the tool when required. Only use light oil to lubricate

the tool. Other lubricants may not be suitable and could damage the tool or

cause a malfunction during use.

Table 2

V1.1 Gas Pressure Washer 8913212

Visit www.princessauto.com for more information 15

STORAGE

PRESSURE WASHER STORAGE

1. Disconnect the spray gun from the high pressure hose after the

pressure washer is cool and the water pressure is released.

2. Drain all water from the high pressure hose, coil it and store it in cradle

of pressure washer handle.

3. Drain all water from the spray gun and spray wand by holding the

spray gun in the vertical position with nozzle pointed downward.

Squeeze trigger to remove fluids. Store in spray gun/hose holder.

4. Store siphon hose, high pressure hose and spray wand so they are

protected from damage, such as being run over.

PROTECTING INTERNAL SEALS

The internal seals require additional preparation if the pressure washer is

stored for more than 30 days or freezing temperatures are expected.

PUMP SAVER

Pump saver comes in a pressurized or unpressurized container. The liquid

is released from the pressurized container by pressing a button. The

unpressurized version is a squeeze bottle.

1. Remove the high pressure hose from the pump outlet. Empty the water

from the hose.

a. You may choose to keep the spray gun connected to the pump to

protect it as well. Keep the trigger depressed while using the pump

saver during step 5 until the liquid no longer flows. Then remove and

store the spray gun along with the hose.

2. Remove the garden hose from the pump inlet. Empty the water from

the hose.

3. Force water from the pump by pulling the recoil starter 6 times.

4. Attach the pump saver container to the pump inlet.

5. Pressurized – Press the button and wait until the liquid flows through

the outlet port.

Unpressurized – Squeeze the bottle for force the liquid into the pump.

Pull the engine’s recoil rope slowly until liquid flows through the outlet

port. You may need to squeeze additional pump saver liquid into the

pump during this step.

8913212 Gas Pressure Washer V1.1

16 For technical questions call 1-800-665-8685

6. Remove the pump saver container and plug the pump’s inlet and outlet.

RV ANTIFREEZE

RV antifreeze is an alternative if pump saver is not available.

1. Obtain a funnel, six ounces of RV (Recreational Vehicle) antifreeze and

approximately 36 inches of garden hose with a male hose connector on

one end.

NOTICE! Only RV antifreeze is suitable. Other types of antifreeze are

corrosive and can damage the pressure pump.

2. Disconnect the spark plug lead and ensure it cannot touch any metal on

the pressure washer by wrapping the lead in insulating tape.

3. Connect the 36 in. length of garden hose to the pump’s water inlet.

4. Place the funnel in the end of the hose and add the RV antifreeze.

5. Pull engine starter rope slowly several times until antifreeze comes out

of pressure hose connection of the pressure pump.

6. Remove the garden hose from water inlet of pressure pump and seal

the pump’s inlet and outlet.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

IMPORTANT! DO NOT pollute the environment by allowing uncontrolled

discharge of waste oil.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

Consult the Engine manual to troubleshoot engine issues.

Problem(s) Possible Cause(s) Suggested Solution(s)

No pressure or Low

pressure.

1. Low water supply.

2. Nozzle obstructed.

3. Water filter screen

obstructed.

1. Water supply must be 2.5

GPM @ 20 psi.

2. Clean nozzle of debris.

3. Remove and clean filter.

V1.1 Gas Pressure Washer 8913212

Visit www.princessauto.com for more information 17

4. Defective thermal relief

valve.

5. Air in hose.

6. High pressure hose too

long.

4. Replace the thermal relief

valve or have a qualified

technician repair it.

5. Stop engine and water source.

Disconnect water source from

pump inlet and turn water

source to ON to remove all air

from hose. When steady

stream of water is present,

turn water source to OFF. Re-

connect water source to pump

inlet and turn on water

source. Squeeze trigger to

remove remaining air.

6. Use hose under 100 ft.

Pump will not draw

chemical or

detergent.

1. Spray gun not set to

low pressure.

2. Chemical filter clogged.

3. Chemical screen not

fully in chemical.

1. See Check Spray Wand and

Pressure Nozzles section.

2. Clean Filter.

3. Ensure end of siphon hose is

fully submerged into chemicals.

Pump will not draw

chemical or

detergent.

4. Chemical solution too

thick.

5. Pressure hose too long

6. Chemical build-up in

chemical injector.

4. Dilute chemical. Chemical

solutions should have same

consistency as water.

5. Lengthen water supply hose

instead of pressure hose.

6. Have parts cleaned or replaced

by authorized dealer.

No or low pressure

(after period of

normal use).

1. Worn seal or packing.

2. Worn or obstructed

valves.

3. Worn unloader piston.

4. Worn E-Z start valve.

Have parts cleaned or replaced by

authorized dealer.

Water leaking at

spray gun/spray

wand connection.

1. Worn or broken

O-ring.

2. Loose hose connection.

1. Check and replace O-ring.

2. Tighten hose connection.

Water leaking at

pump.

1. Loose connections.

2. Piston packing is worn.

1. Tighten connections.

8913212 Gas Pressure Washer V1.1

18 For technical questions call 1-800-665-8685

3. Worn or broken

O-rings.

4. Pump head or tubes

damaged from

freezing.

2 to 4. Have parts cleaned or

replaced by authorized dealer.

Pump pulsates. Nozzle obstructed. See Check Spray Wand and

Pressure Nozzles section.

Detergent not

mixing

1. Siphon hose end not

submerged in

detergent.

2. Not using Black Soap

Nozzle.

1. Adjust siphon hose so the end

is submerged in detergent.

2. Attach Soap Nozzle to allow

proper mixing of water and

detergent.

V1.1 Gas Pressure Washer 8913212

Visit www.princessauto.com for more information 19

PARTS BREAKDOWN

PARTS LIST

# DESCRIPTION QTY

1 Engine 1

2 Grip 1

3 Frame Base 1

4 Soap Tank 1

5 Bolt M8 8

6 M6 Self-Lock Nut 2

7 Rubber Feet 2

8 Bolt M6*25 2

9 Axle 2

10 Plate washer 4

11 Wheels 2

12 Circlip 2

13 Bolt M6*45 2

14 Washer, Rocker 8

15 Cap, Soap Tank 1

8913212 Gas Pressure Washer V1.1

20 For technical questions call 1-800-665-8685

# DESCRIPTION QTY

16 Engine Mount, Vibration

Isolator

4

17 Triangle Knob, M8 Self-

Lock Nut

2

18 Plate washer 2

19 Bolt 2

20

Handle 1

21 Handle grip 1

22

Hex Socket Screw 4

23

Panel 1

24 Nozzle Holder 5

25

Siphon Tube 1

26

Siphon filter 1

27 Bolt M8*20 4

28

Pump 1

29

Shaft Key 1

30

Wand 1

31 Spray Gun 1

32

High Pressure Hose 1

33

O-ring 2

34 Nozzle Cleaner 1

35

Smart cover 1

36

Red Nozzle 0° 1

37 Yellow Nozzle 15° 1

38

Green Nozzle 25° 1

39

White Nozzle 40° 1

40

Black Soap Nozzle 65° 1

41 Spark plug wrench 1

42

Funnel 1

La page charge ...

Powerfist 8913212 Le manuel du propriétaire

Powerfist 8913212 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents