Cannon LAKE-TROLL Manuel utilisateur

Marque: Cannon

Modèle: LAKE-TROLL

Taper: Manuel utilisateur

LAKE-TROLL

MANUAL DOWNRIGGER

USER MANUAL

Model: ______________________________________________________________________

Serial Number: ________________________________________________________________

Purchase Date: ________________________________________________________________

Store Where Purchased: __________________________________________________________

Please thoroughly read this user manual. Follow all instructions and heed all safety and cautionary notices below. Use of this downrigger is only

permitted for persons that have read and understood these user instructions. Minors may use this product only under adult supervision.

ATTENTION: Your Cannon downnrigger should only be used for its intended purpose. Improper use will void the warranty and may be a safety risk.

CAUTION: Persons whose ability to run the downrigger or whose reactions are impaired by alcohol, drugs, medication, or other substances are not

permitted to use this product.

THANK YOU

Thank you for purchasing a Cannon downrigger. We have designed your new downrigger to be an accurate and reliable

tool that will enhance ﬁ shing control and improve your ability to catch ﬁ sh. We hope that you enjoy the use of your

new downrigger and enjoy the beneﬁ t of controlled depth ﬁ shing for years to come by always following safe boating

practices and laws wherever you are ﬁ shing.

This manual covers installation and the operation of your downrigger. Read this manual carefully before operating your

new Cannon downrigger. Retain this manual for future reference.

REMEMBER TO KEEP YOUR RECEIPT AND IMMEDIATELY REGISTER YOUR DOWNRIGGER.

To receive all the beneﬁ ts for your product warranty, please ﬁ ll out and mail the enclosed registration card. You may

also complete registration on our website at cannondownriggers.com.

LOCATING YOUR SERIAL NUMBER

Your Cannon 11-character serial number is very important. It helps to determine the speciﬁ c model and year of manufacture. When contacting

Consumer Service or registering your product, you will need to know your product’s serial number. We recommend that you write the serial number

down in the space provided below so that you have it available for future reference.

CE MASTER USER MANUAL (FOR CE CERTIFIED MODELS)

The serial number on your Cannon Lake-Troll

downrigger is located on the bottom of the

mounting base.

Made by Cannon

Johnson Outdoors

Marine Electronics, Inc.

121 Power Drive

Mankato, MN 56001 USA

Downriggers

Produced in 2015

LAKE-TROLL MANUAL DOWNRIGGER

MODEL 1901250

SER NO K365 CN12345

EXAMPLE

cannondownriggers.com | 3

TABLE OF CONTENTS

Warranty / Service Information 4

Assembly & Installation 5-10

Features 5

Mounting 6-7

Installing the Boom 8

Attaching Swivel Head to Boom 8

Attaching the Crank Handle Assembly 8

Attaching the Rod Holder 9

Terminating the Downrigger Cable 10

Attaching the Line Release 10

Operating the Downrigger 11

BlowBack Calculations 12

Service & Repair 13

Compliance Statements 14

Parts Diagram 15

CANNON LIMITED WARRANTY

Johnson Outdoors Marine Electronics, Inc. (“JOME”) extends the following limited warranty to the original retail purchaser only. Warranty coverage is not

transferable.

CANNON® LIMITED LIFETIME WARRANTY

JOME warrants to the original purchaser that if the accompanying product (see exclusions below) proves to be defective in material or workmanship within the

following warranty periods, JOME will, at its option, either repair or replace same without charge (but no cash refunds will be made):

The boom, motor (if applicable), and reels, plus all plastic parts, including but not limited to frames and bases, will be free from defects in materials and

workmanship, subject to normal wear and tear, for the original purchaser’s lifetime.

All other items will have 1-year limited warranties from the date of original retail purchase, except THE FOLLOWING ITEMS THAT HAVE NO WARRANTY:

swivel lock pin, weights, and wire cable.

LIMITATION AND EXCLUSION OF IMPLIED WARRANTIES AND CERTAIN DAMAGES

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIMITED WARRANTIES. JOME DISCLAIMS LIABILITY FOR INCIDENTAL AND CONSEQUENTIAL

DAMAGES, AND IN NO EVENT SHALL ANY IMPLIED WARRANTIES (EXCEPT ON THE BOOM, MOTOR, REELS, AND ALL PLASTIC PARTS), INCLUDING ANY

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXTEND BEYOND ONE YEAR FROM THE DATE OF PURCHASE

(AND IN THE CASE OF THE SWIVEL LOCK PIN, WEIGHTS, AND WIRE CABLE, JOME DISCLAIMS ALL IMPLIED WARRANTIES). THIS WRITING CONSTITUTES

THE ENTIRE AGREEMENT OF THE PARTIES WITH RESPECT TO THE SUBJECT MATTER HEREOF; NO WAIVER OR AMENDMENT SHALL BE VALID UNLESS

IN WRITING SIGNED BY JOME.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of consequential damages, so the above limitation or

exclusion may not apply to you. This warranty gives you speciﬁ c legal rights, and you may also have other rights that vary from state to state.

CANNON® SERVICE POLICY

AFTER THE APPLICABLE WARRANTY PERIOD

After the applicable warranty period, or, if one of the above exclusions applies, Cannon® products will be repaired for a charge of parts plus labor. All factory

repairs, after the applicable warranty period, carry a 90-Day Limited Warranty, subject to the exclusions and limitations stated above.

TO ENFORCE WARRANTY OR TO OBTAIN REPAIRS AFTER WARRANTY

To obtain warranty service in the U.S., the downrigger believed to be defective and the proof of original purchase (including the date of purchase) must be

presented to a Cannon® Authorized Service Center or to Cannon®’s factory service center in Mankato, MN. Except as noted below, any charges incurred for

service calls, transportation or shipping/freight to/from the Cannon® Authorized Service Center or Cannon®’s factory, labor to haul out, remove, re-install

or re-rig products for warranty service, or any similar items are the sole and exclusive responsibility of the purchaser. Warranty service can be arranged by

contacting a Cannon® Authorized Service Center or by contacting the factory at 1-800-227-6433 or by email to [email protected]. If the

necessary repairs are covered by the warranty, we will pay the return shipping charges to any destination within the United States. Downriggers purchased

outside of the U.S. (or parts of such downriggers) must be returned prepaid with proof of purchase (including the date of purchase and serial number) to any

Authorized Cannon® Service Center in the country of purchase.

NOTE: Do not return your Cannon® downrigger or parts to your retailer. Your retailer is not authorized to repair or replace them.

Major parts, such as the motor and main frame, must be returned to JOME in Mankato, Minnesota, or a Cannon® Authorized Service Center, for repair or

replacement. To reduce shipping costs, we suggest removal of loose parts such as the boom and rod holders. Small parts that can be easily removed such as

the handle and/or the counter, may be removed from the downrigger and returned for repair or replacement. Retain your sales receipt. Proof of purchase

must accompany product when returned.

Return Address:

Johnson Outdoors Marine Electronics, Inc.

Attn: Cannon Service Dept.

121 Power Drive

Mankato, MN 56001

LIMITED WARRANTY

cannondownriggers.com | 5

ASSEMBLY & INSTALLATION

DOWNRIGGER PARTS DESCRIPTION

1. Reel: This is used to spool the cable, available in lengths ranging from 150 to 400 feet.

2. Boom: This is used to extend the weight out from the body of the downrigger and has a pulley ﬁxed to its end. The

boom length is 18 inches.

3. Swivel Head and Depth Meter: This relays the cable at the end of the boom to lower the weight, and provides

information as to how much cable you have run out, enabling you to choose your trolling depth.

4. Weight: This is used to maintain the depth at which you want to ﬁsh. Sizes of weights range from 4 to 10 lbs.

5. Cable: This connects to the weight.

6. Mounting Base: This attaches to the boat, enabling you to place the downrigger where you choose.

7. Rod Holder: This holds your ﬁshing rods while trolling and may also be used for storing rods.*

* This diagram is for reference only and may differ from your actual downrigger.

DOWNRIGGER MOUNTING

Choosing a good location to mount your downrigger on your boat is

very important. A downrigger should be mounted in a location where

it is easy to observe your ﬁ shing rod and react quickly to operate the

downrigger once there is a ﬁ sh on the line.

INSTALLING THE INCLUDED MOUNTING BASE

Decks thinner than 1/4”

Use a Cannon deck plate (sold separately - PN 2200693) to prevent deﬂ ection and add

stability to decks thinner than 1/4”. Use the deck plate as a template to mark the hole locations.

If access to the underside of the deck is not available, the deck plate can be mounted using screws

and wellnuts (not included). Use the deck plate as a template to mark locations and drill 4

wellnut clearance holes. Use four 1/4-20 x 1-1/2” ﬂ at head screws and four wellnuts to

mount deck plate. Tighten the screws so the wellnuts are ﬁ rmly compressed.

Where the underside is accessible, the deck plate can be mounted using

screws, nuts, and washers. Drill 9/32” holes. Use four 1/4-20 x 1-1/2” ﬂ at head

screws, nuts and washers (ﬂ at and lock). Fasten plate to deck. To secure the

mounting base to the deckplate use four 1/4-20 x 1” truss head screws.

Typical Mounting Positions

MOUNTING ACCESSORIES

Cannon offers a complete line of mounting accessories that allow

you to optimize your spread to ﬁ t the way you ﬁ sh. Before making

any permanent changes to your boat, consider what accessories

might be used in your application. To see the complete line of

mounting accessories available, visit cannondownriggers.com.

Deck Plates are necessary when extra strength must be added to the base

material of the boat and for attaching the downrigger to other mounting

accessories.

Gimbal Mounts are designed to ﬁ t medium-sized ﬂ ush mounted rod

holders built into the gunwale of many larger ﬁ shing boats and cruisers.

Only sturdy, high quality rod holders should be used for this temporary

mounting system. Gimbal mounts are available in 9” or 12” post lengths.

Clamp Mounts can be mounted at the junction of two rail sections with

the aid of two ¼” pieces of plywood. They will protect your rail from any

marks from the clamp and provide a non-slip surface.

Side/Rail mounts can be mounted to a welded T-section. It can also be used

at the two rail section butt joint. In both installations it is recommended to

use a non-slip material, such as rubber or a thin wood sheet, between metal

surfaces.

You can also use these for mounting to a very narrow side gunwale. There

is a plate provided for back-up with bolts and washers. If the gunwale

compartment is foamed in, then wellnuts should be used. It is also

recommended to install two additional ﬂ at head screws through the top plate

for stabilization (you will need to drill and countersink).

Deckplate

Gimbal Mount

Clamp Mount

Side Rail Mount

on T-Section

Side Rail Mount

on Gunwhale

ASSEMBLY & INSTALLATION

Decks from 1/4” to 7/16” thick

Where access to the underside of the deck is not available, the mounting

base can be attached to the deck using wellnuts. Use the base as a

template to mark locations and drill four wellnut clearance holes. Mount

the base using four 1/4-20 x 1-1/2” truss head screws and four wellnuts.

Tighten the screws so the wellnuts are ﬁ rmly compressed as pictured.

Decks thicker than 7/16”

For decks thicker than 7/16”, or where the underside of the deck is

accessible, mount the base with screws, nuts, and washers. Use the

base as a template to mark the locations and drill four 9/32” holes. Use

four 1/4-20 x 2” truss head screws and four each ﬂ at washers and nuts.

Fasten the base to the deck as pictured.

NOTE: Wellnuts SHOULD NOT be used on decks thicker than 7/16”.

NOTE: When using the telescopic boom, we strongly recommend the

use of a deck plate on all boats to provide adequate stability for the

downrigger.

Low-Proﬁ le Swivel Base

To mount the Low-Proﬁ le Swivel Base, follow the same procedure as for the deck

plate with this exception: use four 1/4”-20 x 1-1/2” truss head screws to fasten the

mounting base and four additional 1/4”-20” x 2-1/2” truss head screws to attach the

swivel base tothe boat deck.

INSTALLING THE BOOM

1. Insert boom into frame (Figure 1) and line up holes in boom with holes in frame.

NOTE: Easi-Troll units require the included boom adapter.

Decks from 1/4” to 7/16” Thick

Decks Thicker Than 7/16”

Low-Proﬁ le Swivel Base

cannondownriggers.com | 7

ASSEMBLY & INSTALLATION

MOUNTING THE DOWNRIGGER ON THE INCLUDED BASE

Slide the bottom of the frame over the lip of the base, with the boom outboard

or facing the stern. Move the frame over the base until the latch clicks into place.

If properly seated, the frame should completely cover the base.

CAUTION: If not fully seated, your downrigger can be dislodged from the base.

NOTE: Periodically check base to ensure integrity. It is recommended that the

base be replaced once every ﬁve years.

ATTACHING THE CRANK HANDLE ASSEMBLY

1. Make sure the thrust bearing is placed between both thrust washers.The

spring should be oriented with the narrow end is toward the bearing.

2. Slide the bearing, washers and spring over the shaft.

3. Carefully thread the crank handle onto the shaft and continue turning the

handle clockwise until the clutch is fully tightened.

Thrust Bearing

Spring

Race

Bearings

Crank Handle

Boom

Frame

Boom Locking Screw

Boom End

Screws

Swivel Head

ASSEMBLY & INSTALLATION

INSTALLING THE BOOM

1. Insert the boom into the downrigger frame.

2. Secure it by seating it ﬁrmly against the shoulder inside the frame and fastening the

boom locking screw (#8 X 1” self tapping) so that it engages the hole in the boom.

ATTACHING SWIVEL HEAD TO THE BOOM

1. Spread the swivel head side plates and slip the assembly over the boom end.

2. Leave the corrugated spacer in place until the assembly is snapped together.

3. Remove the spacer and install the two #4 x 1/2” screws into the swivel head.

NOTE: Adjusting the angle of the boom head can help control cable wrap on the reel.

Recommended Area

to Clamp Rod Holder

Angled

Shoulder

Star Washer

Placement

cannondownriggers.com | 9

ASSEMBLY & INSTALLATION

ATTACHING THE ROD HOLDER

The positive lock rod holder incorporates a locking disk

that allows the rod holder to be aligned in 15 degree

increments. Slide the rod holder tube into the clamp to the

desired position within the recommended area (see below).

1. Slide the rod holder tube into the clamp to the desired

position within the recommended area (see below).

2. Be sure the angled shoulders are facing up. Place the

locking disk into the mating recess of the frame.

3. Slip the clamp arms in place where the obround tab on

the disk ﬁts into the slot on the clamp.

4. Slide the star washer between the arm of the clamp and

the frame. Place the ﬂat washer onto the bolt.

5. Insert the bolt with washer through the clamp by entering

the disk, going through the frame, the star washer, and

out the other side of the clamp. Tighten the nut to secure

the rod holder.

6. Reposition the rod holder by loosening the nut and

adjusting the tilt.

CAUTION: This rod holder is intended for use of up to

30 lb. test line only, and is not recommended for use with any tackle IGFA rated higher than 30 lb. A safety strap (not

included) is recommended for all applications.

The rod holder assembly is not warranted when used with tackle above 30 lbs. Equipment placed in the rod holders

and the loss thereof is the responsibility of the user and is in no way warranted by CANNON, INC.. Mounting must be in

accordance with the above instructions and diagram to be warranted.

TERMINATING THE DOWNRIGGER CABLE

NOTE: Use only straight cable when routing through the terminator. Worn or kinked cable can be stressed and may

break prematurely when retrieving trolling weights.

NOTE: A set of pliers with wire cutters is recommended for this part of setup.

1. Unwind about 2 feet of cable and

thread through the rubber cushion.

Attach Swivel Snap to terminator.

2. Examine the top of the terminator

and note the order shown in the

detail to run cable.

3. Lead and pull six inches of cable

through HOLE A. Thread cable

through swivel, then up into bottom

of the terminator. Lead cable out of

HOLE B and into HOLE C. Push the

cable until its end touches the inside

of the terminator hook. Tighten cable

by squeezing terminator until it snaps

shut. Then pull at top and bottom

until drawn tight. Make sure that the

cable threads the hook.

NOTE: Use only straight cable, not kinked cable.

4. Slide the cushion over the top of the terminator and give it a test pull. The cable is now set to attach a Cannon Flash Weight™.

Open

Tension Adjust

Fishing Line

Gripper Pads

ATTACHING THE LINE RELEASE (UNI-RELEASE)

The Cannon Uni-Release attaches directly to the downrigger weight. Attach

ﬁ shing line to the clip at the end of the release, and then click through a

series of increasing tension settings. The release can be used with any test

line on salt or fresh water and may be adjusted from 2 to 22 pounds of grip

tension on the line.

To change line release tension, turn tension knob to (+) to increase or (-)

to decrease. Tension also may vary according to where the line is placed in

the grips. Higher tension is on the line if it is set back toward the hinge, and

lower if set closer to the opening. To open the release, spread the release

arms with thumb and foreﬁ nger applying pressure to the sides.

Step 2.

Rubber

Cushion

Step 1.

Step 3. Step 4.

A. CABLE

IN C. CABLE

B. CABLE

OUT

HOLE A

Swivel

HOLE B

HOLE C

Cable

Snap

Swivel

ASSEMBLY & INSTALLATION

OPERATING YOUR DOWNRIGGER

After mounting the Cannon downrigger to your boat, release some line from your rod and reel so that the lure is

anywhere from 5 to 100 feet behind the boat. This is called drop back.

Attach the ﬁ shing line ﬁ rmly into the line release (see “Attaching the Line Release” for instructions). Lower the weight

to the desired depth as indicated on the depth meter. Place the ﬁ shing rod in the rod holder and reel up the slack so

that your rod has a slight bend in it. When a ﬁ sh strikes the lure, the line will separate from the release. Then you will be

free to ﬁ ght the ﬁ sh and bring it in on your rod and reel.

LOWERING THE WEIGHT

You can lower the trolling weight at a controlled rate by turning

the crank handle gently counter-clockwise (away from the boom).

Depending on how far you turn, you can let your trolling weight

descend as fast or as slowly as you wish. Turn the crank handle

clockwise (toward the boom) until the clutch is tight (the continuous

clicking will stop and the handle will not turn forward any further).

This gives you control to let it plunge rapidly or sink slowly to a

predetermined trolling depth. With multiple downriggers, you could

start all your weights creeping down, one at a time, and then stop

them each in turn.

RAISING THE WEIGHT

Turn the crank handle clockwise (toward the boom) as rapidly as you

desire to retrieve the trolling weight.

ADJUSTING THE CLUTCH TENSION

The clutch is built into the crank mechanism. Turn crank handle clockwise to increase the drag and counterclockwise to

reduce it.

CAUTION: Remove weight from downrigger before traveling either by water or transporting on trailer.

To Lower Weight

To Raise Weight

ADJUSTING THE DEPTH METER

The depth meter is located on the side of the swivelhead, as pictured. You can raise or

lower your depth by turning the crank handle. The depth meter counts the revolutions

of the reel and reﬂects your depth in feet. To reset the depth meter, simply turn the reel

with your ﬁngers backwards or forwards until you reach 0.

cannondownriggers.com | 11

OPERATING THE DOWNRIGGER

BLOWBACK

Simply stated, blowback is what happens to the downrigger weight when you pull it through the water behind your boat.

As your speed increases, so does the horizontal distance between the weight and your downrigger. The faster you go,

the farther the weight is behind you. The farther the weight is behind you, the shallower the weight is.

The following charts provide you with blowback information for three sizes of Cannon downrigger weights pulled at

three different speeds with no lures attached and with no current. Current drag, water salinity and the use of non-

Cannon products will affect your actual trolling depth.

As an example, the ﬁ rst chart shows that if you are trolling at 4 MPH with an 8 pound weight and you have 100FT. of

cable in the water with no current; the down rigger ball is actually at a depth of about 80 FT.

Cable Length (ft.)

100

120

140

160

100

120

140

160

8-Lb Weight at 2, 4, and 6 MPH

2 MPH

4 MPH

6 MPH

Actual Depth of Weight (ft.)

Cable Length (ft.)

100

120

140

160

100

120

140

160

10-Lb Weight at 2, 4, and 6 MPH

2 MPH

4 MPH

6 MPH

Actual Depth of Weight (ft.)

Cable Length (ft.)

100

120

140

160

100

120

140

160

12-Lb Weight at 2, 4, and 6 MPH

2 MPH

4 MPH

6 MPH

Actual Depth of Weight (ft.)

BLOWBACK CALCULATIONS

FREQUENTLY ASKED QUESTIONS

We have FAQs available on our website to help answer all of your Cannon questions. Visit www.cannondownriggers.com

and click on “Frequently Asked Questions” under the “Service” tab to ﬁ nd an answer to your question.

CALL US (FOR U.S. AND CANADA)

Our customer service representatives are available Monday – Friday between 7:00am – 4:30pm CST at 800-227-6433.

If you are calling to order parts, please have the 11-character serial number from your product, speciﬁ c part numbers,

and credit card information available. This will help expedite your call and allow us to provide you with the best customer

service possible. You can reference the parts list located in your manual to identify the speciﬁ c part numbers.

EMAIL US

You can email our customer service department with questions regarding your Cannon products. To email your quesiton,

visit www.cannondownriggers.com and click on “Contact Us” under the “Service” tab.

REPLACEMENT PARTS

In the U.S.A., replacement parts may be ordered directly from CANNON Parts Dept., 121 Power Drive, Mankato,

Minnesota 56001. Be sure to provide the MODEL and SERIAL numbers of your downrigger when ordering parts. Please

use the correct part numbers from the parts list. Payment for any parts ordered from the CANNON Parts Department may

be by cash, personal check, Discover Card, MasterCard or VISA. To order, call 1-800-227-6433 or FAX 1-800-527-4464.

AUTHORIZED SERVICE CENTERS

Cannon works with authorized service centers in the United States and Canada to provide parts and service for your

downrigger. Please visit our Authorized Service Center page to locate a service center in your area.

cannondownriggers.com | 13

SERVICE & REPAIR

ENVIRONMENTAL COMPLIANCE STATEMENT:

It is the intention of JOME to be a responsible corporate citizen, operating in compliance with known and applicable

environmental regulations, and a good neighbor in the communities where we make or sell our products.

WEEE DIRECTIVE:

EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors,

sellers, and manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of

consumer electronics to take responsibility for the management of waste from their products to achieve environmentally

responsible disposal during the product life cycle.

WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be

required for EEE designed and intended as ﬁ xed or temporary installation in transportation vehicles

such as automobiles, aircraft, and boats. In some European Union member states, these vehicles are

considered outside of the scope of the Directive, and EEE for those applications can be considered

excluded from the WEEE Directive requirement.

This symbol (WEEE wheelie bin) on product indicates the product must not be disposed of with other

household refuse. It must be disposed of and collected for recycling and recovery of waste EEE.

Johnson Outdoors Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal

to comply in the collection, treatment, recovery, and environmentally sound disposal of those products; however, these

requirement do vary within European Union member states. For more information about where you should dispose

of your waste equipment for recycling and recovery and/or your European Union member state requirements, please

contact your dealer or distributor from which your product was purchased.

DISPOSAL:

Johnson Outdoors Inc. products are not subject to the disposal regulations EAG-VO (electric devices directive) that

implements the WEEE directive. Nevertheless never dispose of your product in a garbage bin but at the proper place of

collection of your local town council.

Never dispose of battery in a garbage bin. Comply with the disposal directions of the manufacturer or his representative

and dispose of them at the proper place of collection of your local town council.

COMPLIANCE STATEMENTS

cannondownriggers.com | 15

PARTS DIAGRAM

LAKE-TROLL MANUAL DOWNRIGGER

This page provides Cannon® WEEE compliance disassembly instructions.

For more information about where you should dispose of your waste equipment for

recycling and recovery and/or your European Union member state requirements,

please contact your dealer or distributor from which your product was purchased.

Tools required, but not limited to:

-ﬂ at head screw driver

-Phillips screw driver

-socket set

-pliers

-wire cutters.

ITEM QTY PART

NUMBER DESCRIPTION

1 1 3330001 FRAME - LAKE-TROLL (LEXAN)

2 1 3395617 DECAL - NOSE, LAKE-TROLL

3 2 9010001 BEARING - REEL SHAFT

4 2 9430210 WASHER - 7/8" NYLON ROUND

5 1 3397917 REEL - ROUGH 3.75" (LEXAN)

6 1 1080001 SHAFT - REEL

7 1 3393412 SCREW - SET 5/16"-18 X 1" (REEL)

8 1 3775392 SPOOL CABLE SS [150.FT]

9 1 9100070 CABLE LEADER SLEEVE

10 10467695 BRAKE PLATE - REEL

11 13391710 CLUTCH PAD

12 10467694 BRAKE PLATE - RATCHET

13 11000904 SHAFT - RATCHET

14 23391737 WASHER - THRUST

15 19010280 BEARING - THRUST

16 19400040 SPRING - HAND CRANK

17 10422002 CRANK HANDLE, LAKE-TROLL

18 11021480 CLUTCH COVER

19 19400070 SPRING - DOG RATCHET

20 19100160 DOG - RATCHET

21 49370220 SCREW - #10 X 1-1/4" FH TYPE A

22 19100721 RED THREAD CAP

23 13395631 DECAL - CANNON SMALL (BLACK)

24 13395630 DECAL - CANNON LARGE (BLACK)

25 12477001 BAG ASSY - SINGLE ROD HOLDER KIT

*26 10290796 >TUBE - ROD HOLDER

*27 12151726 >WASHER - 5/16" FLAT

*28 12383106 >NUT - 5/16"-18 SS

*29 13319005 >CLAMP - ROD HOLDER W/ SLOT

ITEM QTY PART

NUMBER DESCRIPTION

*30 13325002 >DISK - ROD HOLDER

*31 19040310 >BOLT - HEX 5/16"-18 X 2"

*32 19430160 >WASHER - STAR 5/16"

*33 12277002 >UNIVERSAL LINE RELEASE

34 13774001 SWIVEL HEAD ASSEMBLY W/ COUNTER

*35 10267001 SIDE PLATE (RH)

*36 10269726 PULLY - SWIVEL HEAD

*37 10325002 COUNTER - SWIVEL HEAD

*38 10333001 GEAR - INTERMEDIATE, SWIVEL HEAD

*39 10333002 GEAR - REDUCTION, SWIVEL HEAD

*40 10367004 SIDE PLATE (LH), W/ COUNTER

*41 29010070 HDW BEARING BRASS

*42 19100690 CLAMP - RING, PUSH ON

43 13316001 CAP - BOOM END

44 19370002 SCREW - #8-32 SELF TAPPING

45 13778901 TAB LOCK MOUNTING BASE

*46 1 - BASE - TAB LOCK, NO TAB (LEXAN)

*47 13391001 LOCKING TAB

48 12994894 *BAG ASSEMBLY, MOUNTING (KIT #4)

49 42263102 NUT - HEX 1/4"-20

50 42371712 WASHER - 9/32" FLAT

51 19100100 TERMINATOR

52 19100101 TERMINATOR CUSHION

53 19100620 TERMINATOR SNAP & SWIVEL

54 49280713 BOLT - TRUSS 1/4" - 20 X 1-1/2"

55 49280725 BOLT - TRUSS 1/4" - 20 X 2-1/2"

56 39370010 SCREW - #4 X 1/2" PPH

57 49950357 WASHER - LOCK 1/4" SPLIT

58 13310008 16" BOOM - COPOLYMER

CANNON

57(4)

54(4)

21(4)

50(4)

49(4)

55(4)

29 31

* THIS ITEM IS PART OF A KIT AND ONLY LISTED FOR VIEWING PURPOSES.

Cannon Consumer & Technical Service

Johnson Outdoors Marine Electronics, Inc.

PO Box 8129

Mankato, MN 56002-8129

121 Power Drive

Mankato, MN 56001

Phone (800) 227-6433

Fax (800) 527-4464

For a complete listing of Cannon accessories, visit cannondownriggers.com

• Uni-Line Release

• Uni-Stacker Release

• 4 to 12 lb. weights

RECOMMENDED ACCESSORIES

ROD HOLDERS & TRACK SYSTEMS

Incredible versatile rod holders, rock-solid bases and plates. It’s everything you need to rig your boat up to fit the way you

fish - and you can mount it all up on our track system, which features interchangeable components made of high-strength

aluminum.

MOUNTS

Rig it up and reel ‘em in with a variety of mounting options suited to fit the way you fish.

LINE RELEASES & WEIGHTS

We offer a wide variety of downrigger accessories designed to give you the best fishing experience:

ALUMINUM MOUNT TRACK

DUAL AXIS ADJUSTABLE

ROD HOLDER SWIVEL BASE PEDESTAL

CLAMP MOUNTSWIVEL BASE GIMBAL MOUNT

DECK PLATE

Part #3397104 Rev G 05/18

ECN 38752

LAKE-TROLL

TREUIL DE PÊCHE MANUEL

MANUEL DE L’UTILISATEUR

Modèle : _____________________________________________________________________

Numéro de série : ______________________________________________________________

Date de l’achat : _______________________________________________________________

Magasin où l’achat a été effectué : ___________________________________________________

Veuillez lire attentivement ce manuel de l’utilisateur. Suivez toutes les instructions et tenez compte de toutes les consignes de sécurité et les

mises en garde décrites ci-dessous. L’utilisation de ce treuil de pêche n’est autorisée que pour les personnes qui ont lu et compris ces consignes pour

l’utilisateur. Les mineurs peuvent utiliser ce moteur uniquement sous la supervision d’un adulte.

ATTENTION: Votre treuil de pêche Cannon ne devrait être utilisé que pour son intention prévue. L’utilisation inappropriée annulera la garantie et

pourrait créer un risque de sécurité.

MISE EN GARDE: Les personnes dont la capacité à faire fonctionner le treuil de pêche est affaiblie par l’alcool, la drogue, les médicaments ou d’autres

substances ne sont pas autorisées à utiliser ce produit.

MERCI

Merci d’avoir acheté un treuil de pêche Cannon. Nous avons conçu votre nouveau treuil de pêche pour qu’il soit un

outil précis et ﬁ able qui vous permettra d’améliorer le contrôle de la pêche et d’accroître votre capacité d’attraper des

poissons. Nous espérons que vous aimerez utiliser notre nouveau treuil de pêche et que vous proﬁ terez des avantages

de la pêche en profondeur contrôlée pendant des années en respectant toujours les pratiques sécuritaires et les lois en

matière de navigation toutes les fois que vous pêcherez.

Ce manuel traite de l’installation et du fonctionnement de votre treuil de pêche. Lisez attentivement ce manuel avant

d’utiliser votre nouveau treuil de pêche Cannon. Conservez ce manuel pour référence future.

N’OUBLIEZ PAS DE CONSERVER VOTRE REÇU ET D’ENREGISTRER IMMÉDIATEMENT VOTRE TREUIL DE PÊCHE.

Pour recevoir tous les avantages de la garantie de votre produit, veuillez remplir le formulaire d’enregistrement ci-joint et

le retourner par la poste. Vous pouvez aussi remplir votre enregistrement sur notre site Web à cannondownriggers.com.

LOCALISATION DE VOTRE NUMÉRO DE SÉRIE

Le numéro de série à 11 caractères Cannon est très important. Cela permet de déterminer le modèle spéciﬁ que et l’année de fabrication. Lorsque vous

contactez le service à la clientèle ou que vous enregistrez votre article, vous aurez besoin du numéro de série de votre article. Nous vous suggérons

d’inscrire le numéro de série dans l’espace fourni ci dessous aﬁ n qu’il soit disponible ultérieurement.

MANUEL CE D’UN MASTER (CE CERTIFIED MODELS)

The serial number on your Cannon Lake-Troll

downrigger is located on the bottom of the

mounting base.

Made by Cannon

Johnson Outdoors

Marine Electronics, Inc.

121 Power Drive

Mankato, MN 56001 USA

Downriggers

Produced in 2015

LAKE-TROLL MANUAL DOWNRIGGER

MODEL 1901250

SER NO K365 CN12345

EXEMPLE

cannondownriggers.com | 19

TABLE DES MATIÈRES

Garantie / Service d’information 20

Assemblage et Installation 21

Aperçu du Produit 21

Montage 22-23

Installation du Bras 24

Installation de la Poulie d’extrémité 24

Fixation de la Poignée de Manivelle 24

Fixation du Porte-Canne 25

Terminaison du Câble du Treuil de Pêche 26

Fixation du Dispositif de Dévidage de la Ligne 26

Fonctionnement du Treuil de Pêche 27

Coup en Arrière 28

Service et Réparation 29

Déclaration de Conformité 30

Remarques 31

Schéma des Pièces & Liste des Pièces 15

GARANTIE LIMITÉE DE CANNON

Johnson Outdoors Marine Electronics, Inc. (« JOME ») offre la garantie limitée suivante uniquement à l’acheteur au détail initial. La garantie n’est pas

transférable.

GARANTIE À VIE LIMITÉE DE CANNONMD

JOME garantit à l’acheteur initial que si le produit ci joint (voir les exclusions ci-dessous) présente un défaut matériel ou de fabrication pendant la période de

garantie, JOME pourra, selon son choix, réparer ou remplacer le produit, sans frais (mais aucun remboursement en espèces n’aura lieu) :

Le bras, le moteur (le cas échéant) et les moulinets, ainsi que toutes les pièces en plastique, y compris, sans s’y limiter, les cadres et les bases, seront libres de

défauts matériels ou de fabrication, sous réserve d’une usure normale, pour la vie de l’acheteur initial.

Tous les autres articles auront des garanties limitées d’un an de la date de l’achat initial au détail, à l’exception DES ARTICLES SUIVANTS, QUI N’ONT

AUCUNE GARANTIE : l’ergot d’arrêt pivotant, les poids, et le câble en ﬁ l d’acier.

LIMITATION ET EXCLUSION DES GARANTIES IMPLICITES ET CERTAINS DOMMAGES

IL N’Y A AUCUNE GARANTIE EXPRESSE AUTRE QUE LES PRÉSENTES GARANTIES LIMITÉES. JOME DÉCLINE TOUTE RESPONSABILITÉ POUR DES

DOMMAGES INDIRECTS ET ACCESSOIRES, ET AUCUNE GARANTIE IMPLICITE (À L’EXCEPTION DU BRAS, DU MOTEUR, DES MOULINETS ET TOUTES

LES PIÈCES EN PLASTIQUE) NE SE PROLONGERA AU-DELÀ D’UN AN DE LA DATE D’ACHAT, Y COMPRIS TOUTE GARANTIE IMPLICITE DE QUALITÉ

MARCHANDE OU DE CONFORMITÉ À UN USAGE PARTICULIER (ET DANS LE CAS DE L’ERGOT D’ARRÊT PIVOTANT, DES POIDS ET DES CÂBLES EN FIL

D’ACIER, JOME DÉCLINE TOUTE GARANTIE IMPLICITE). LA PRÉSENTE CONSTITUE L’INTÉGRALITÉ DE L’ACCORD ENTRE LES PARTIES RELATIVEMENT À

L’OBJET DES PRÉSENTES; AUCUNE DÉROGATION OU AUCUN AMENDEMENT NE SERA VALIDE À MOINS D’ÊTRE FORMULÉ PAR ÉCRIT ET SIGNÉ PAR

JOME.

Certains états ne permettent pas de limites sur la durée d’une garantie implicite ou l’exclusion ou la limitation des dommages accessoires, les limitations ou

les exclusions ci-dessus peuvent donc ne pas s’appliquer à vous. La présente garantie vous donne des droits légaux spéciﬁ ques et vous pouvez également

bénéﬁ cier d’autres droits qui varient d’un État à l’autre.

POLITIQUE DE SERVICE DE CANNONMD

APRÈS LA PÉRIODE DE GARANTIE APPLICABLE

Après la période de garantie applicable, ou si une des exclusions susmentionnées s’applique, les produits CannonMD seront réparés contre des frais pour les

pièces et le travail. Toutes les réparations d’usine, après la période de garantie applicable, portent une garantie limitée de 90 jours, assujettie aux exclusions

et limitations susmentionnées.

POUR EXÉCUTER LA GARANTIE OU POUR OBTENIR DES RÉPARATIONS APRÈS LA GARANTIE

Pour obtenir le service de garantie aux États-Unis, le treuil de pêche qui semble être défectueux et la preuve d’achat originale (comportant la date d’achat),

doivent être présentés à un centre de service agréé CannonMD ou au centre de service de la manufacture CannonMD à Mankato, au MN. Sauf les cas

indiqués ci-dessous, tous les frais encourus pour des appels de service, de transport ou d’expédition à destination ou à partir du centre de service agréé ou

de l’usine CannonMD, de main-d’œuvre pour transporter, retirer, réinstaller ou regréer les articles retirés pour le service de garantie, ou tout autre élément

semblable sont sous la seule et unique responsabilité unique et exclusive de l’acheteur. Le service au titre de la garantie peut être obtenu en communiquant

avec le centre de service agréé de CannonMD ou l’usine au 1-800-227-6433 ou par courriel à l’adresse suivante [email protected]. Si les

réparations nécessaires sont sous garantie, nous paierons les frais d’expédition de retour à toute destination dans les États-Unis. Les treuils de pêche

achetés à l’extérieur des États-Unis (ou les pièces de ces treuils de pêche) doivent être retournés, port payé avec preuve d’achat (y compris la date d’achat et

le numéro de série), à n’importe quel centre de service agréé CannonMD dans le pays d’achat.

REMARQUE : Ne retournez pas le treuil de pêche Cannon ou les pièces à votre détaillant. Votre détaillant n’est pas autorisé à les réparer ou à les remplacer.

Les pièces importantes, comme le moteur et le cadre principal, doivent être retournées chez JOME à Mankato, au Minnesota, ou à un centre de service agréé

CannonMD, pour la réparation ou le remplacement. Aﬁ n de réduire les coûts d’expédition, nous vous suggérons de retirer toutes les pièces libres, comme le

bras et les porte-cannes. Les petites pièces qui peuvent être facilement retirées, comme la poignée ou le compteur, peuvent être retirées du treuil de pêche et

retournées pour la réparation ou le remplacement. Conservez vos reçus. Une preuve d’achat doit accompagner le produit lors du retour.

Adresse de l’expéditeur :

Johnson Outdoors Marine Electronics, Inc.

à l’attention du : Service auxiliaire Cannon

121 Power Drive

Mankato, MN 56001

GARANTIE LIMITÉE

La page est en cours de chargement...