Empire Direct-Vent Wall Counterflow Le manuel du propriétaire

Marque: Empire

Modèle: Direct-Vent Wall Counterflow

Taper: Le manuel du propriétaire

Ce manuel convient également à

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

Page 1

FAN TYPE

DIRECT

VENT WALL

FURNACE MODEL:

DVC35IPXLP-1 DVC35SPPXLP-1

DVC35IPXNAT-1

DVC35SPPXNAT-1

This appliance may be installed in an aftermarket,

permanently located manufactured home (USA

only) or mobile home, where not prohibited by

state or local codes.

This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with other

gases, unless a certied kit is used.

WARNING

FIRE OR EXPLOSION HAZARD

If the information in these instructions is

not followed exactly, a re or explosion may

result causing property damage, personal

injury or loss of life.

— Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

• If you cannot reach your gas

supplier, call the re department.

— Installation and service must be

performed by a qualied installer,

service agency or the gas supplier.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

WARNING

If not installed, operated and maintained in

accordance with the manufacturer's instructions,

this product could expose you to substances in

fuel or from fuel combustion which can cause

death or serious illness.

37402-5-0620Page 2

TABLE OF CONTENTS

Important Safety Information ......................................................................................................... 3

Safety Information for Users of Propane Gas ............................................................................... 4

Requirements for Massachusetts .................................................................................................. 5

Introduction.................................................................................................................................6-7

Specications ................................................................................................................................ 7

Gas Supply .................................................................................................................................8-9

Clearances .................................................................................................................................... 9

Installation Instructions ........................................................................................................... 10-12

DVC-35SPP Standing Pilot Lighting Instructions ........................................................................ 13

DVC-35IP Intermittent Pilot Lighting Instructions ........................................................................ 14

Pilot Flame Characteristics.......................................................................................................... 15

Main Burner Flame Characteristics ............................................................................................. 16

Wiring .......................................................................................................................................... 16

Service and Maintenance Suggestions ....................................................................................... 17

DVC-35IP Intermittent Pilot Sequence of Operation ................................................................... 18

DVC-35IP Intermittent Pilot System Troubleshooting Sequence ................................................ 19

Parts List ..................................................................................................................................... 20

Parts View ................................................................................................................................... 21

Master Parts Distributor List ........................................................................................................ 22

How To Order Repair Parts ......................................................................................................... 22

Warranty ...................................................................................................................................... 23

SECTION PAGE

37402-5-0620 Page 3

IMPORTANT SAFETY INFORMATION

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

• Due to high temperatures, the appliance should be

located out of trafc and away from furniture and

draperies.

• Children and adults should be alerted to the hazards

of high surface temperatures and should stay away

to avoid burns or clothing ignition.

• Young children should be carefully supervised when

they are in the same room as the appliance.

• Clothing or other ammable material should not be

placed on or near the appliance.

• Any safety screen or guard removed for servicing

an appliance must be replaced prior to operating

the appliance.

• Keep burner and control compartment clean.

• Vent cap hot while furnace is in operation.

• Installation and repair should be done by a QUALI-

FIED SERVICE PERSON. The appliance should be

inspected before use and at least annually by a

qualied service person. More frequent cleaning

may be required due to excessive lint from carpet-

ing, bedding materials, etc. It is imperative that

control compartments, burners and circulating air

passageways of the appliance be kept clean.

• DO NOT put anything around the furnace that will

obstruct the ow of combustion and ventilation air.

• DO keep the appliance area clear and free from

combustible material, gasoline and other ammable

vapors and liquids.

• DO examine venting system periodically and replace

damaged parts.

• DO make a periodic visual check of pilot and burn-

ers. Clean and replace damaged parts.

• CAUTION: Pilot hole cover must be kept tightly

closed during operation.

• DO NOT use this heater if any part has been under

water. Immediately call a qualied service techni-

cian to inspect the heater and to replace any part of

the control system and any gas control which has

been under water.

IMPORTANT: This furnace has a washable permanent

type lter which should be cleaned at least once per

year before the heating season. For dirty or high use

areas, more frequent cleaning is required.

37402-5-0620Page 4

SAFETY INFORMATION FOR USERS OF PROPANE GAS

Propane is a ammable gas which can cause res and explo-

sions. In its natural state, propane is odorless and colorless.

You may not know all the following safety precautions which

can protect both you and your family from an accident. Read

them carefully now, then review them point by point with the

members of your household. Someday when there may not

be a minute to lose, everyone’s safety will depend on knowing

exactly what to do. If, after reading the following information,

you feel you still need more information, please contact your

gas supplier.

PROPANE GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas

because of the odorant put in the Propane Gas. That’s your

signal to go into immediate action!

• Do not operate electric switches, light matches, use your phone.

Do not do anything that could ignite the gas.

• Get everyone out of the building, vehicle, trailer, or area. Do

that IMMEDIATELY.

• Close all gas tank or cylinder supply valves.

• Propane Gas is heavier than air and may settle in low areas

such as basements. When you have reason to suspect a gas

leak, keep out of basements and other low areas. Stay out

until reghters declare them to be safe.

• Use your neighbor’s phone and call a trained Propane Gas

service person and the re department. Even though you may

not continue to smell gas, do not turn on the gas again. Do not

re-enter the building, vehicle, trailer, or area.

• Finally, let the service man and reghters check for escaped

gas. Have them air out the area before you return. Properly

trained Propane Gas service people should repair the leak,

then check and relight the gas appliance for you.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell

the odor of the chemical put into the gas. You must nd out if

you can smell the odorant in propane. Smoking can decrease

your ability to smell. Being around an odor for a time can affect your

sensitivity or ability to detect that odor. Sometimes other odors in

the area mask the gas odor. People may not smell the gas odor or

their minds are on something else. Thinking about smelling a gas

odor can make it easier to smell.

The odorant in Propane Gas is colorless, and it can fade under

some circumstances. For example, if there is an underground

leak, the movement of the gas through soil can lter the odorant.

Odorants in Propane Gas also are subject to oxidation. This fading

can occur if there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into

walls, masonry and other materials and fabrics in a room. That will

take some of the odorant out of the gas, reducing its odor intensity.

Propane Gas may stratify in a closed area, and the odor intensity

could vary at different levels. Since it is heavier than air, there may

be more odor at lower levels. Always be sensitive to the slightest gas

odor. If you detect any odor, treat it as a serious leak. Immediately

go into action as instructed earlier.

SOME POINTS TO REMEMBER

• Learn to recognize the odor of Propane Gas. Your local Propane

Gas Dealer can give you a “Scratch and Sniff” pamphlet. Use

it to nd out what the propane odor smells like. If you suspect

that your Propane Gas has a weak or abnormal odor, call your

Propane Gas Dealer.

• If you are not qualied, do not light pilot lights, perform service,

or make adjustments to appliances on the Propane Gas system.

If you are qualied, consciously think about the odor of Propane

Gas prior to and while lighting pilot lights or performing service

or making adjustments.

• Sometimes a basement or a closed-up house has a musty

smell that can cover up the Propane Gas odor. Do not try to

light pilot lights, perform service, or make adjustments in an

area where the conditions are such that you may not detect

the odor if there has been a leak of Propane Gas.

• Odor fade, due to oxidation by rust or adsorption on walls of

new cylinders and tanks, is possible. Therefore, people should

be particularly alert and careful when new tanks or cylinders

are placed in service. Odor fade can occur in new tanks, or

reinstalled old tanks, if they are lled and allowed to set too

long before relling. Cylinders and tanks which have been out

of service for a time may develop internal rust which will cause

odor fade. If such conditions are suspected to exist, a periodic

sniff test of the gas is advisable. If you have any question

about the gas odor, call your Propane Gas Dealer. A peri-

odic sniff test of the Propane Gas is a good safety measure

under any condition.

• If, at any time, you do not smell the Propane Gas odorant and

you think you should, assume you have a leak. Then take the

same immediate action recommended above for the occasion

when you do detect the odorized Propane Gas.

• If you experience a complete “gas out,” (the container is under

no vapor pressure), turn the tank valve off immediately. If the

container valve is left on, the container may draw in some air

through openings such as pilot light orices. If this occurs, some

new internal rusting could occur. If the valve is left open, then

treat the container as a new tank. Always be sure your con-

tainer is under vapor pressure by turning it off at the container

before it goes completely empty or having it relled before it is

completely empty.

37402-5-0620 Page 5

REQUIREMENTS FOR MASSACHUSETTS

For all side wall horizontally vented gas fueled equipment installed

in every dwelling, building or structure used in whole or in part for

residential purposes, including those owned or operated by the

Commonwealth and where the side wall exhaust vent termination

is less than seven (7) feet above nished grade in the area of the

venting, including but not limited to decks and porches, the following

requirements shall be satised:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At

the time of installation of the side wall horizontal vented gas fu-

eled equipment, the installing plumber or gastter shall observe

that a hard wired carbon monoxide detector with an alarm and

battery back-up is installed on the oor level where the gas

equipment is to be installed. In addition, the installing plumber

or gastter shall observe that a battery operated or hard wired

carbon monoxide detector with an alarm is installed on each

additional level of the dwelling, building or structure served by

the side wall horizontal vented gas fueled equipment. It shall be

the responsibility of the property owner to secure the services

of qualied licensed professionals for the installation of hard

wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas fu-

eled equipment is installed in a crawl space or an attic,

the hard wired carbon monoxide detector with alarm and

battery back-up may be installed on the next adjacent oor

level.

b. In the event that the requirements of this subdivision can not

be met at the time of completion of installation, the owner

shall have a period of thirty (30) days to comply with the

above requirements; provided, however, that during said

thirty (30) day period, a battery operated carbon monoxide

detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon

monoxide detector as required in accordance with the above

provisions shall comply with NFPA 720 and be ANSI/UL 2034

listed and IAS certied.

3. SIGNAGE. A metal or plastic identication plate shall be per-

manently mounted to the exterior of the building at a minimum

height of eight (8) feet above grade directly in line with the

exhaust vent terminal for the horizontally vented gas fueled

heating appliance or equipment. The sign shall read, in print size

no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY

BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall

horizontally vented gas fueled equipment shall not approve

the installation unless, upon inspection, the inspector observes

carbon monoxide detectors and signage installed in accordance

with the provisions of 248 CMR 5.08(2)(a) 1 through 4.

(b) EXEMPTIONS: The following equipment is exempt from

248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled “Equip-

ment Not Required To Be Vented” in the most current

edition of NFPA 54 as adopted by the Board; and

2. Product Approved side wall horizontally vented gas

fueled equipment installed in a room or structure

separate from the dwelling, building or structure used

in whole or in part for residential purposes.

VENTING SYSTEM PROVIDED. When the manufacturer of

Product Approved side wall horizontally vented gas equip-

ment provides a venting system design or venting system

components with the equipment, the instructions provided

by the manufacturer for installation of the equipment and

the venting system shall include:

1. Detailed instructions for the installation of the venting

system design or the venting system components; and

2. A complete parts list for the venting system design or

venting system.

(e) A copy of all installation instructions for all Product Approved

side wall horizontally vented gas fueled equipment, all

venting instructions, all parts lists for venting instructions,

and/or all venting design instructions shall remain with the

appliance or equipment at the completion of the installation.

37402-5-0620Page 6

INTRODUCTION

Introduction

Always consult your local Building Department regarding regula-

tions, codes or ordinances which apply to the installation of a di-

rect vent wall furnace.

Instructions to Installer.

Installer must leave instruction manual with owner after

installation.

2. Installer must have owner ll out and mail warranty card supplied

with furnace.

3. Installer should show owner how to start and operate furnace.

WARNING

Any change to this furnace or its control can be dangerous.

This is a heating appliance and any panel, door or guard

removed for servicing an appliance must be replaced prior

to operating the appliance.

To Conserve Gas: Turn off pilot when heater is not in use.

General Information

This furnace is design certied in accordance with American

National Standard/CSA Standard Z21.86 and CSA 2.32 by the

Canadian Standards Association, as a fan type direct vent wall

furnace to be installed according to these instructions.

Any alteration of the original design, installed other than as

shown in these instructions or use with a type of gas not

shown on the rating plate is the responsibility of the person

and company making the change.

Important

All correspondence should refer to complete Model No., Serial

No., and type of gas.

NOTICE: During initial ring of this unit, its paint will bake out and

smoke will occur. To prevent triggering of smoke alarms, ventilate

the room in which the unit is installed.

Installation on Rugs and Tile

If this appliance is installed directly on carpeting, tile or other

combustible material other than wood ooring, the appliance shall

be installed on a metal or wood panel extending the full width and

depth of the appliance.

The base referred to above does not mean the re-proof base as

used on wood stoves. The protection is for rugs that are extremely

thick and light colored tile.

Installation in Residential Garages

Gas utilization equipment in residential garages shall be installed

so that all burners and burner ignition devices are located not less

than 18” above the oor.

Such equipment shall be located, or protected, so it is not subject

to physical damage by a moving vehicle.

Qualied Installing Agency

Installation and replacement of gas piping, gas utilization

equipment or accessories and repair and servicing of equipment

shall be performed only by a qualied agency. The term “qualied

agency” means any individual, rm, corporation or company

which either in person or through a representative is engaged

in and is responsible for (a) the installation or replacement of

gas piping or (b) the connection, installation, repair or servicing

of equipment, who is experienced in such work, familiar with all

precautions required and has complied with all the requirements

of the authority having jurisdiction.

Commonwealth of Massachusetts: The installation must be

made by a licensed plumber or gas tter in the Commonwealth

of Massachusetts.

The installation must conform with local codes or, in the absence of

local codes, with the National Fuel Gas Code ANSI Z223.1/NFPA

54* Natural Gas and Propane Installation Code, CSA B149.1.

* Available from the American National Standards Institute, Inc., 11

West 42nd St., New York, N.Y. 10036

High Altitudes

For altitudes/elevations above 2,000 feet, input ratings should be

reduced at the rate of 4 percent for each 1,000 feet above sea

level. For Canadian high altitude applications, this appliance is

suitable for installation at elevations between 0 feet and 4,500 feet

without change.

Piezo Pilot Ignitor Instructions

Depressing the red button completely causes a spark to occur at

the pilot. This is a substitute for a match which requires opening

the pilot hole cover.

To light the pilot, it is important that the electrode be 1/8” from the

thermocouple. The spark must occur at the point the burner ame

hits the thermocouple. The end of the electrode will be red hot with

the pilot on.

On a new installation with air in the gas line, it is suggested that a

match be used. The match will light the pilot faster than the piezo

under this condition.

Well Head Gas Installations

Some natural gas utilities use “well head” gas. This may affect

the Btu output of the unit and promote sooting. Units shall not be

converted to use well head gas.

CONVERSION KITS

Model Number Description Used On

DV1350 Propane to Natural DVC35IPXLP-1

DV1348 Natural to Propane DVC35IPXNAT-1

DV1346 Propane to Natural DVC35SPPXLP-1

DV1344 Natural to Propane DVC35SPPXNAT-1

37402-5-0620 Page 7

SPECIFICATIONS

Model DVC-35SPP DVC-35IP

Input BTU/HR 35,000 35,000

Height 72 1/2” 72 1/2”

Width 14 1/8” 14 1/8”

Depth 10 3/8” 10 3/8”

Gas Inlet 1/2” Pipe 1/2” Pipe

CFM 275 275

Accessories

SOR-1 Register, Side Outlet

SOK-1 Side Outlet Kit, 10” (25.4cm) Boot Assembly with Register

VINYL SIDING VENT KITS

Model Number Description

*DV-822 Vinyl Siding Vent Kit

VSK2 Vinyl Siding Vent Kit

INTRODUCTION (CONT’D)

When an existing Category 1 heater is removed or replaced, the

original venting system may no longer be sized to properly vent the

attached appliances. Instructions shall also indicate effects of an

improperly sized venting system (formation of condensate, leakage,

spillage, etc.) and shall specify the following test procedure:

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each

appliance connected to the venting system being placed

into operation could result in carbon monoxide poisoning

or death.

The following steps shall be followed for each appliance

connected to the venting system being placed into

operation, while all other appliances connected to the

venting system are not in operation:

1. Seal any unused openings in the venting system.

2. Inspect the venting system for proper size and

horizontal pitch, as required in the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the Natural Gas and

Propane Installation Code, CSA B149.1 and these

instructions. Determine that there is no blockage or

restriction, leakage, corrosion and other deciencies

which could cause an unsafe condition.

3. As far as practical, close all building doors and

windows and all doors between the space in which

the appliance(s) connected to the venting system are

located and other spaces of the building.

4. Close replace dampers.

5. Turn on clothes dryers and any appliance not connected

to the venting system. Turn on any exhaust fans, such

as range hoods and bathroom exhausts, so they are

operating at maximum speed. Do operate a summer

exhaust fan.

6. Follow the lighting instructions. Place the appliance

being inspected into operation. Adjust the thermostat

so appliance is operating continuously.

7. Test for spillage from draft hood equipped appliances

at the draft hood relief opening after 5 minutes of main

burner operation. Use the ame of a match or candle.

8. If improper venting is observed during any of the

above tests, the venting system must be corrected in

accordance with National Fuel Gas Code, ANSI Z223.1/

NFPA 54 and/or Natural Gas and Propane Installation

Code, CSA B149.1.

9. After is has been determined that each appliance

connected

to the venting system properly vents when

tested as outlined above, return doors, windows,

exhaust fans, replace dampers and any other gas-red

burning appliance to their previous conditions of use.

37402-5-0620Page 8

GAS SUPPLY

Locating Gas Supply

The gas line can enter the unit either through the oor or outside

wall. The gas line opening should be made at this time. Location

of the opening will be determined by the position of oor joists and

the valve and union used for servicing.

RECOMMENDED GAS PIPE DIAMETER

Pipe

Length

Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

Natural Propane Natural Propane

0-10 feet

0-3 meters

1/2”

12.7 mm

3/8”

9.5mm

1/2”

12.7 mm

3/8”

9.5 mm

10-40 feet

4-12 meters

1/2”

12.7 mm

1/2”

12.7mm

5/8”

15.9 mm

1/2”

12.7 mm

40-100 feet

13-30 meters

1/2”

12.7 mm

1/2”

12.7mm

3/4”

19 mm

1/2”

12.7 mm

100-150 feet

31-46 meters

3/4”

19 mm

1/2”

12.7 mm

7/8”

22.2 mm

3/4”

19 mm

NOTE: Never Use plastic pipe. Check to conrm whether your lo-

cal codes allow copper tubing or galvanized.

NOTE: Since some municipalities have additional local codes, it

is always best to consult your local authority and installation code.

The use of the following gas connectors is recommended:

– ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing

and Fittings

– ANS Z21.45 Assembled Flexible Appliance Connectors of

Other Than All-Metal Construction

The above connectors may be used if acceptable by the author-

ity having jurisdiction. The Commonwealth of Massachusetts re-

quires that a exible appliance connector cannot exceed three feet

in length.

FLEXIBLE GAS LINE CONNECTION

GAS SUPPLY

TEE HANDLE

FLEX TUBING

NPT NIPPLE

FLARE SHUT OFF VALVE

FLARE FITTING

RIGID GAS LINE CONNECTION

CLOSE NIPPLE

TEE HANDLE

NPT NIPPLE

NPT UNION

SHUT OFF VALVE

NPT GAS SUPPLY

Figure 1

Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/

CGA-B149 (.1 or .2) installation code.

Installing a New Main Gas Shut-Off

Each appliance should have its own manual gas shut-off.

A manual main gas shut-off should be located in the vicinity of

the unit. Where none exists, or where its size or location is not

adequate, contact your local authorized installer for installation or

relocation.

Compounds used on threaded joints of gas piping shall be resis-

tant to the action of liqueed petroleum gases. The gas lines must

be checked for leaks by the installer. This should be done with a

soap solution watching for bubbles on all exposed connections,

and if unexposed, a pressure test should be made.

Never use and exposed ame to check for leaks. Appliance

must be disconnected from piping at inlet of control valve

and pipe capped or plugged for pressure test. Never pres-

sure test with appliance connected; control valve will sustain

damage!

A gas valve and ground joint union should be installed in the gas

line upstream of the gas control to aid in servicing. It is required

by the National Fuel Gas Code that a drip line be installed near

the gas inlet. This should consist of a vertical length of pipe tee

connected into the gas line that is capped on the bottom in which

condensation and foreign particles may collect.

GAS SUPPLY PIPING

1/8 NPT PLUGGED HOLE

FOR TEST GAGE

GROUND JOINT UNION

3” MINIMUM

MANUAL SHUT-OFF VALVE

GAS SUPPLY

INLET

1/8 NPT PLUGGED HOLE

FOR TEST GAGE

GAS

VALVE

Figure 2

METHOD OF INSTALLING A TEE FITTING SEDIMENT TRAP

Pressure Testing of the Gas Supply System

1. To check the inlet pressure to the gas valve, a 1/8” N.P.T.

plugged tapping, accessible for test gauge connection, must

be placed immediately upstream of the gas supply connection

to the appliance.

2. The appliance and its individual shut-off valve must be discon-

nected from the gas supply piping system during any pressure

testing of that system at test pressures in excess of 1/2 psig

(3.5 kPa).

3. The appliance must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psig (3.5 kPA)

Attention! If one of the above procedures results in pressures in

excess of 1/2 psig (14” w.c) (3.5 kPa) on the appliance gas valve,

it will result in a hazardous condition.

37402-5-0620 Page 9

TOP VIEW OF VALVE

PRESSURE REGULATOR

OUTLET PRESSURE TA

GAS OUTLET

PILOT GAS OUTLET

PILOT ADJUSTMENT

SCREW BENEATH

COVER SCREW

MANUAL GAS COCK KNOB

RED RESET BUTTON

INLET

PRESSURE TAP

GAS INLET

WRENCH BOSS

VENT

Checking Manifold Pressure

Both Propane and Natural Gas valves have a built-in pressure reg-

ulator in the gas valve. Natural Gas models will have a manifold

pressure of approximately 4.0” w.c. (.996kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 5.0” w.c.

(1.245kPa) for the purpose of input adjustment to a maximum of

7.0” w.c. (1.743kPa). Propane Gas models will have a manifold

pressure approximately 10.0” w.c. (2.49kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 11.0” w.c.

(2.739kPa) for the purpose of input adjustment to a maximum of

13.0” w.c. (3.237kPa).

A 1/8” N.P.T. plugged tapping, accessible for test gauge connec-

tion, is located on the outlet side of the gas control.

The built-in regulator comes on at approximately 1/4th pressure

and full on in 10 seconds.

Figure 3

CLEARANCES

Pressure Testing Of The Gas Supply System

1. In selecting a location for installation, it is necessary to provide

adequate accessibility clearances for servicing and proper in-

stallation. A front clearance of 36” (91.4cm) is recommended.

Do not block outlet or inlet air openings on the front grill.

2. The DVC-35 minimum wall depth is 3/4” (19mm) and maximum

wall depth is 10” (254mm). The use of tubes not supplied by

the manufacturer results in unsatisfactory performance.

3. The DVC-35 can be attached to the wall or recessed into

the wall up to 9 1/2” (241mm) in depth but the minimum 3/4”

(19mm) vent/air intake system wall depth must be maintained.

Example: If furnace is recessed into the wall at a depth of 9 1/2”

(241mm), the minimum wall depth must be 10 1/4” (260mm).

4. The wall in which the furnace is recessed has (0) zero clear-

ance to the furnace sides and top.

5. When using side discharge registers, SOR-1 or SOK-1, the

furnace cannot be recessed into the wall.

6. Clearance to sidewall or combustible material is 4” (102mm).

7. Ceiling clearance is 4” (201mm).

8. Floor and rear wall clearance is (0) zero inches.

9. Clearance of 18” (457mm) is required to sidewall or combus-

tible material when ush mounted SOR-1, side outlet register

is used.

10. The minimum distance from the center of the vent cap to the

nearest outside corner or obstruction is 12” (305mm).

Figure 4

The vent terminal of this direct vent appliance shall be located

at least 9” (229mm) from any opening through which ue gases

could enter a building. The bottom of the vent terminal and the air

intake shall be located at least 12” (305mm) above grade. See

vent location, Figure 4.

WARNING

The nearest point of the vent cap should be a minimum

horizontal distance of six (6) feet (1.83m) from any pressure

regulator. In case of regulator malfunction, the six (6) feet

(1.83m) distance will reduce the chance of gas entering the

vent cap.

GAS SUPPLY (CONT’D)

37402-5-0620Page 10

INSTALLATION INSTRUCTIONS

Locating Wall Opening

The furnace is to be located on an outside wall. Locate wall studs

so that wall opening will be located between wall studs. The fur-

naces is 14 1/8” (358mm) in width and can be recessed between

standard 16” (406mm) on center wall stud. The wall opening re-

quired as shown in Figure 5 is a diameter of 7 1/2” (191mm).

Locate and cut wall opening. If there is insulation above the wall

opening (air inlet tube) a barrier should be installed above the wall

opening (air inlet tube) to prevent insulation from coming in con-

tact with the air inlet tube. The barrier must not penetrate into the

7-1/2” (191mm) diameter wall opening.

A template is provided in furnace carton for positioning furnace on

the wall. Also, refer to Figure 5 and Figure 7 for positioning the

furnace on wall and for locating gas line connection.

Installing Optional Side Outlets

Side outlet register, SOR-1 may be installed on one or both sides

of the furnace at the required clearances of 18” (457mm) to adja-

cent wall or combustible material as shown in Figure 6.

1. Turn “OFF” all electric power to the furnace.

2. Remove the front panel from the furnace.

3. Remove the (2) #8 X 3/8” (9mm) screws that attach the inner

shield cover plate to the inner shield.

4. Scribe a line between the four dimples on the outer casing side

to form a square.

5. Drill a pilot hole within the scribed square on the outer casing.

Remove the sheet metal within the scribed square with a tin

snips or comparable tool. Attention! Do not cut the electrical

wires located between the outer casing and the inner shield.

6. Insert the 5” x 5” (127mm x 127mm) inner boot through the

outer casing. Align the clearance holes on the inner boot with

the crew holes on the inner shield. Attach inner boot to inner

shield with (2) #8 x 3/8” (9mm) screws removed in Step 3.

7. Place the register over the 5 1/2” (140mm) square opening with

the louvers set for the desired direction and mark the mounting

holes using the register as a template.

8. Drill (2) 1/8” diameter holes in cabinet side and attach the

9. Installation of SOR-1 is completed.

Side outlet kit, SOK-1, 10” (254mm) boot assembly with register,

for warm air discharge into an adjoining room may be installed on

either side of the furnace at the required clearance of 4” (102mm)

to adjacent wall as shown in Figure 6.

To install SOK-1, please use step 1 through 5 in the SOR-1 in-

structions for DVC-35 furnaces. Then, use the following Steps to

complete the installation of the SOK-1.

1. Using the inner and outer boots as hole templates, mark and

drill (4) 1/8” (3mm) diameter holes in the inner shield and (4)

1/8” (3mm) diameter holes in the cabinet side.

2. Locate and cut a 6 3/4” (171mm) square opening through wall.

3. Attach furnace to wall (see Attaching Furnace to Wall).

4. With furnace in place, after checking alignment of side outlet

opening in wall and furnace, place the 9 3/8” x 9 3/8” (238mm

x (238mm) side outlet wall plate over outer boot, pass the outer

boot through the wall and attach side wall plate to furnace side

of wall with (2) #10 x 1 1/2” (38mm) provided screws.

5. Attach outer boot to the cabinet side with (4) #8 x 1/4” (6mm)

provided screws.

6. Position and attach inner boot to inner shield with (4) #8 x 1/4”

(6mm) provided screws.

7. Place the register over the 6 3/4” (171mm) square opening with

the louvers positioned for the desired discharge direction and

mark the mounting holes using the register as a template.

8. Drill (2) 1/8” (3mm) diameter holes in the wall and attach the

9. Installation of SOK-1 is completed.

Figure 5

4”

MINIMUM TO COMBUSTIBLE

ALL OR SURFACE

VENT

TERMINA

4” MINIMUM TO COMBUSTIBLE

WALL OR SURFACE

18”MIN. CLEARANCE TO

WALL OR COMBUSTIBLE

SURFACE USING

MODEL

SOR-1 SIDE REGISTER

5½”

12”

CLEARANCE FOR SIDE OUTLET KITS TO ADJACENT W

ALL

UNIT CANNOT BE RECESSED

WHEN SIDE REGISTERS ARE

USED.

WHEN SIDE REGISTERS ARE

NOT USED, UNIT MAYBE RECESSED

UP TO 9 1/2”

Figure 6

37402-5-0620 Page 11

Locating Electric Supply

A 7/8” (22mm) diameter knockout is provided at the bottom of the

left and right side panels. A three-prong (grounding) plug assembly

is located within the control compartment (bottom) of the furnace.

Please remove 7/8” (22mm) knockout from appropriate side panel

when routing plug assembly to an electrical outlet. Unit can be

hard wired when recessed. Remove the 3 prong plug assembly

and terminate inside the unit junction box.

Figure 7

Installation of Three-prong (Grounding) Plug Assembly

1. Disconnect nylon cap on 3’ (92cm) plug assembly from nylon

plug on wiring harness. Remove 3’ (92cm) plug assembly from

control compartment (bottom) of the furnace.

2. Remove 7/8” (22mm) knockout from appropriate side panel.

3. Insert nylon cap on 3’ (92cm) plug assembly into the 7/8” (22mm)

hole in the side panel.

4. Connect nylon cap on 3’ (92cm) plug assembly to nylon plug

on the wiring harness.

5. Place 7/8” (22mm) strain relief bushing around the cord of the 3’

(92cm) plug assembly. Insert 7/8” (22mm) strain relief bushing

into the 7/8” (22mm) hole in the side panel.

Attention! The 7/8” (22mm) strain relief bushing is located

within the same envelope as the Installation Instructions and

Owner’s Manual.

Attaching Furnace to Wall

Refer to Figure 5 for the location of the 7 1/2” (191mm) diam-

eter wall opening for the furnace. After the wall opening has been

located and cut, position ue outlet on furnace in center of wall

opening. When attaching furnace to the wall, remove that portion

of baseboard and molding on the wall which is behind the furnace.

Attach furnace to wall, at the outer casing top, with (2) toggle bolts

provided and to oor, at the out casing bottom, with (2) #10 x 1 1/2”

(38mm) screws provided.

Cutting Vent Tubes

This is the most important part of the installation. With the furnace

installed on the wall, the 6” (152mm) diameter inlet tube and the 4”

(102mm) diameter ue outlet tube are to be marked and cut using

the following procedure.

1. Attach 6” (152mm) diameter air inlet tube onto the collar of air

drop assembly. Be sure 6” (152mm) diameter air inlet tube is

placed as far as possible onto the collar of the air drop assem-

bly. Mark the 6” (152mm) diameter air inlet tube 1/2” (13mm)

beyond the outside wall. Remove 6” (152mm) diameter air inlet

tube from collar of air drop assembly.

2. Attach 4” (102mm) diameter ue outlet tube onto ue outlet

collar on combustion chamber. Be sure 4” (102mm) diameter

ue outlet tube is placed as far as possible onto the collar of

ue outlet. Mark the 4” (102mm) diameter ue outlet tube 2 1/4”

(57mm beyond the outside wall. Remove 4” (102mm) diameter

ue outlet tube from collar of ue outlet on combustion chamber.

Mark or wrap tape completely around the tubes at the marked

points to help in making a true cut. Do not crimp or enlarge tubes.

Installing Vent Assembly (See Figure 8)

1. Place caulking (not provided) beneath the edge of the outside

mounting plate. Use additional caulking to correct uneven wall

surface, such as clapboard.

2. Attach 6” (152mm) diameter air inlet tube onto the collar of air

drop assembly. Attach caulked, outside mounting plate into

the 6” (152mm) diameter air inlet tube. Position the outside

mounting plate so that 6” (152mm) diameter air inlet tube has a

slight downward slope to the outside. The downward slope is

necessary to prevent the entry of rainwater. Attach outside

mounting plate to exterior wall with (4) #10 x 1 1/2” (38mm)

screws provided.

3. Apply furnace cement or RTV silicone sealant to 4” (102mm)

diameter ue outlet collar on combustion chamber and to

4” (102mm) diameter collar on vent cap. Attach 4” (102mm)

diameter ue outlet tube onto ue outlet collar on combustion

chamber. Attach vent cap into the 4” (102mm) diameter ue

outlet tube. Attach vent cap to outside mounting plate with (3)

#10 x 1/2” (13mm) screws provided.

4. Installation is complete.

Figure 8

INSTALLATION INSTRUCTIONS (CONT’D)

37402-5-0620Page 12

Reassembly and Resealing Vent-Air Intake System

When vent-air intake system is removed for servicing the furnace,

the following steps will assure proper reassembly and resealing of

the vent-air intake assembly.

1. Remove old caulking beneath the edge of the outside mount-

ing plate. Apply new caulking beneath the edge of the outside

mounting plate. Use additional caulking to correct uneven wall

surface, such as clapboard.

2. Remove old furnace sealant from ue outlet collar on combustion

chamber and collar of vent cap. Remove old furnace sealant

from both ends of 4” (102mm) diameter ue outlet tube.

3. Attach 6” (152mm) diameter air inlet tube onto the collar of air

drop assembly. Attach caulked, outside mounting plate into

the 6” (152mm) diameter air inlet tube. Position the outside

mounting plate so that 6” (152mm) diameter air inlet tube has

a slight downward slope to the outside. The downward slope

is necessary to prevent the entry of rainwater. Attach outside

mounting plate to exterior wall with (4) #10 x 1 1/2” (38mm)

screws provided.

4. Apply furnace cement or RTV silicone sealant to 4” (102mm)

diameter ue outlet collar on combustion chamber and to

4” (102mm) diameter collar on vent cap. Attach 4” (102mm)

diameter ue outlet tube onto ue outlet collar on combustion

chamber. Attach vent cap into the 4” diameter ue outlet tube.

Attach vent cap to outside mounting plate with (3) #10 x 1/2”

(13mm) screws provided.

5. Reassembly and resealing vent-air intake system is completed.

Installing a Vent Near a Window Ledge,

Other Type of project or on Siding (vinyl, aluminum, etc.)

Direct vent furnaces are designed to be installed on a uniform out-

side wall. When the wind comes from any angle (up, down, or from

either side), it must hit the vent cap equally over both the air inlet

and the ue outlet portions of the vent. Any wall projection, such

as a door or window casing, which disturbs the wind on one side of

the air inlet section will result in back pressure on the ue section

smothering the ame and eventual pilot outage.

When the vent cap is to be installed on siding or it appears that

a projection within 6” (152mm) of any side of the air inlet section

could shield the air inlet section, the entire vent should be sup-

ported away from the wall at least the distance of the projection. 2”

x 4” (51mm x 102mm) framing whose outside dimensions match

the overall dimensions of the mounting plate is recommended.

The 2” x 4” (51mm x 102mm) framing protects siding from possible

warpage or discoloration. All joints can then be sealed and painted.

The wall depth plus the additional depth of the 2” x 4” (51mm x

102mm) framing should not exceed a total depth of 10” (254mm)

for DVC-35. See Figure 9. If it does, you will need to use the DV-

1190 Extended Flue Kit.

INSTALLATION INSTRUCTIONS (CONT’D)

Vinyl siding kit, DV-822, is available from Empire Comfort Sys-

tems, Inc. The depth is 3” (76mm), which enables the vent cap to

be extended away from siding or projections. The wall depth plus

the additional 3” (76mm) depth of the vinyl siding vent cap exten-

sion should not exceed a total depth of 10” (254mm) for DVC-35.

See Figure 10.

Figure 9 Figure 10

WARNING

When vinyl siding vent kit, DV-822 or 2” x 4” (51mm x 102mm)

framing is added to an existing installation (furnace is

installed) do not attempt to add sections of pipe to the ue

outlet tube or air inlet tube. An air tight seal is required for

both tubes. Refer to Parts List, page 20 to order tubes.

37402-5-0620 Page 13

DVC-35SPP STANDING PILOT LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

A. This appliance has a pilot which must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the oor because some

gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone, Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the re

department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or

turn by hand, don’t try to repair it; call a qualied service

technician. Force or attempted repair may result in a re

or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualied service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

LIGHTING INSTRUCTIONS

1. STOP! Read safety information above.

2. Turn off all electric power to the appliance.

3. Remove control access panel (lower front panel).

4. Turn gas control knob clockwise

to “OFF.”

5. Wait ten (10) minutes to clear out any gas. Then smell

for gas, including near the oor. If you smell gas, STOP!

Follow “B” in the safety information above. If you don’t

smell gas, go to the next step.

6. Remove the pilot access cover located on the combustion

chamber.

7. Find pilot - follow metal

tube from gas control.

The pilot is located

between the two burner

tubes behind the pilot

access cover.

8. Turn gas control knob counterclockwise

“Pilot.”

9. Push and hold red reset button down completely and

repeatedly push the ignitor button until the pilot burner

is lit. Pilot may also be lit with a match. Continue to hold

the red rest button down for about one (1) minute after

the pilot is lit. Release button and it will pop back up. Pilot

should remain lit. If it goes out, repeat step 4 through 9.

• If button does not pup up when released, stop and

immediately call a qualied service technician or gas

supplier.

• If the pilot will not stay lit after several tries, turn

the gas control knob to “OFF” and call your service

technician or gas supplier.

10. Replace pilot access cover.

11. Turn gas control knob counterclockwise

“ON.”

12. Replace control access panel (lower front panel).

13. Turn on all electric power to the appliance.

SCONTROL KNOBSHOWN IN “OFF”POSITION

THERMOCOUPLE

PILOT BURNER

TO TURN OFF GAS TO APPLIANCE

1. Turn off all electric power to appliance if service is to be

performed.

2. Remove control access panel (lower front panel).

3. Push in gas control knob slightly and turn

clockwise to “OFF.” Do not force.

4. Replace control access panel (lower front panel).

WARNING

If you do not follow these instructions exactly, a re or explosion may result causing property damage,

personal injury or loss of life.

37402-5-0620Page 14

DVC-35IP INTERMITTENT PILOT LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

A. This appliance is equipped with an ignition device which

automatically lights the pilot. Do NOT try to light the pilot

by hand.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the oor because some

gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone, Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or

turn by hand, don’t try to repair it; call a qualied service

technician. Force or attempted repair may result in a re

or explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualied service technician

to inspect the appliance and to replace any part of the

control system and any gas control which has been under

water.

OPERATING INSTRUCTIONS

1. STOP! Read safety information above.

2. Turn off all electric power to the appliance.

3. This appliance is equipped with an ignition device which

automatically lights the pilot. Do not try to light the pilot

by hand.

HONEYWELL IP SMART VALVE

4. Remove front panel door.

5. Slide gas control switch to “OFF.”

6. Wait ten (10) minutes to clear out any gas. Then smell

for gas, including near the oor. If you smell gas, STOP!

Follow “B” in the safety information above. If you don’t

smell gas, go to the next step.

7. Slide gas control switch to “ON.”

8. Replace front panel door.

9. Turn on all electric power to the appliance.

10. If the appliance will not operate, follow the instructions,

“TO TURN OFF GAS TO APPLIANCE” and call your

service technician or gas supplier.

IGNITOR

CONTROL

OFF

GAS FLOW

GAS VALVE SHOWNIN OFF POSITION

TO TURN OFF GAS TO APPLIANCE

1. Turn off all electric power to the appliance if service is

to be performed.

2. Remove front panel door.

3. Slide gas control switch to “OFF.”

4. Replace front panel door.

WARNING

If you do not follow these instructions exactly, a re or explosion may result causing property damage,

personal injury or loss of life.

37402-5-0620 Page 15

PILOT FLAME CHARACTERISTICS

The correct pilot ame (Figure 11) will be blue, extending past

the thermocouple. The ame will surround the thermocouple just

below the tip.

Natural Gas pilots require adjusting when the inlet gas pressure

is above 5” w.c. (1.245kPa). Remove the pilot cover screw on the

control valve (Figure 3), and turn the adjustment screw clockwise

to reduce ame. Replace pilot cover screw to eliminate gas leak-

ing at that control valve opening.

Propane Gas will not require adjustment.

After use, cleaning may be required for the proper ame.

IP-Model Pilot

This heater is using a Honeywell “Smart Valve” system for intermit-

tent pilot ignition.

On a call for heat, this control turns on a 24 volt mini hot surface

ignitor which lights a pilot that in turn lights the main burner. The

gas valve used in this system is a step opening which opens at a

lower pressure for ignition and then steps to a full inlet pressure

of 4” W.C. pressure on Natural Gas and 10” W.C. pressure on

Propane Gas.

Pilot Flame Adjustment

The pilot ame should envelop 3/8 to 1/2 inch (10 to 13mm) of the

tip of the ame rod. See Figure 11.

To adjust:

1. Remove the pilot adjustment cover screw.

2. Turn the inner adjustment screw clockwise

to de-

crease or counterclockwise to increase pilot

ame. Pilot adjustment is shipped at full ow rate. Turn the

inner adjustment screw clockwise

if the inlet pres-

sure is too high.

3. Replace the cover screw after the adjustment to prevent gas

leakage.

THERMOCOUPLE

BURNER

SPARK

ELECTRODE

PILOT

STANDING PILOT

THERMOCOUPLE

PILOT SHIELD

SPARK

ELECTRODE

PILOT LOCATION END VIEW

STANDING PILOT SHOWN

3/8”TO 1/2”

PILOT FLAME

GROUND

ELECTRODE

BURNER

PILOT

HOT SURFACE

IGNITOR

FLAME

ROD

IP-MODEL PILOT

Figure 11

37402-5-0620Page 16

MAIN BURNER FLAME CHARACTERISTICS

The correct ame will be a short, blue inner ame with a much

larger, light blue, outer ame. The burner does not have a primary

air adjustment. The ame will be correct if the factory-set pressure

and orice opening are used. After the furnace has been operating,

the burner ports may be blocked by foreign matter carried in by

combustion air. Therefore, cleaning of the burner may be needed

for proper ame.

The clean burner port disconnect the gas supply to the valve, and

remove the screws fastening the burner. After removing the burner

door from the burner box, remove each main burner. Pilot mount-

ing bracket will need to be unscrewed and moved out the way to

remove all burners. Burners can be blown out using compressed

air or by blowing through them. Be sure there is no lint or foreign

debris blocking the burner ports. Reassemble using the same

screws earlier removed and locate pilot in the same position as

before and noted above.

Figure 12

WIRING

The appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical

Code, CSA C22.1, if an external electrical source is utilized. This

appliance is equipped with three-prong (grounding) plug for

your protection against shock hazard and should be plugged

directly into a properly grounded three-prong receptacle. Do

not cut or remove the grounding prong from this plug. For an

ungrounded receptacle, an adapter, which has two prongs and a

wire for grounding, can be purchased, plugged into the ungrounded

receptacle and its wire connected to the receptacle mounting screw.

With this wire completing the ground, the appliance cord plug can be

plugged into the adapter and be electrically grounded. A 7/8” hole

is provided in the junction box for use with a conduit connector if

local codes require this type of protection.

Installing the ON/OFF Device

To install an ON/OFF device (such as a wall switch, remote, toggle

switch, or thermostat), remove the wire nut from the two wires from

the valve. Run additional wire from the valve wires to the ON/OFF

device. Install the ON/OFF device in the same room as the furnace

following the installation instructions supplied with it. In the absence

of instructions, install the ON/OFF device 4 to 5 feet above the oor

on an interior wall not affected by another heating source (i.e. stove

or water heater) or the temperature of an adjoining room.

CAUTION

Label all wires prior to disconnection when servicing controls.

Wiring errors can cause improper and dangerous operation.

Verify proper operation after servicing.

To Conserve Gas: Turn off pilot when heater is not in use.

Figure 13

LIMIT CONTROL

——— — ——————————————— —

CONTRÔLE

LIMITE

TRANSFORMER

——— —— —————————————————— —

TRANSFORMATEUR

SPT-3 CORDSET

——— —— ——————————————— —

CORDON SPT-3

WHITE (BLANC)

BLACK (NOIR)

MOTOR

————— —————

MOTEUR

WIRING DIAGRAM

————————————————————

CÂBLAGE DE DIAGRAMME

YELLOW (JAUNE)

AUTO FAN

——— —— ——————————— —

VENTILATEUR

AUTO

IF ANY OF THE ORIGINAL WIRE AS SUPPLIED

WITH THIS UNIT MUST BE REPLACED, IT MUST

BE REPLACED WITH 150°C THERMOPLASTIC

4/64 THICK OR ITS EQUIVALENT.

120V. 60Hz. LESS THAN 3 AMPS

S´IL YAUN FIL ORIGINAL FOURNI AVEC

L´APPAREIL QUI DOIT ÊTRE REMPLACÉ. IL DOIT

ÊTRE REMPLACÉ AVEC UN ÉQUIVALENT À FIL

4/64” THERMOPLASTIQUE 150°C.

120V. 60Hz. MOINS DE 3 AMPS.

—————— ———————————————————————————————————————————————

RED/WHT (ROUGE/BLANC)

RED (ROUGE)

LADDER WIRING DIAGRAM

——————————————————————————

ÉCHELLE ÉLECTRIQUE

SCHÉMATIQUE

RED/WHT

ROUGE/BLANC

TRANSFORMER

——— —— —————————————————— —

TRANSFORMATEUR

24 VOLTS

120 VOLTS

RED/WHT

ROUGE/BLANC

BLACK

NOIR

RED/WHT

ROUGE/BLANC

LOW VOLTAGE (BAS VOLTAGE)

120 VOLTS

JUNCTION BOX

—— —— ——— —————————————— ——

BOÎTE DE JONCTION

RED/WHT

ROUGE/BLANC

LIMIT SWITCH

——— — ——————————————— —

CONTRÔLE DE

TOLÉRANCE

BLK (NOIR)

GRN (VERT)

WHT (BLANC)

BLK (NOIR)

IP UNITS

YELLOW

JAUNE

WHITE

BLANC

BLACK

NOIR

MOTOR

————— —————

MOTEUR

AUTO FAN

——— —— ——————————— —

VENTILATEUR

AUTO

ON/OFF DEVICE

——— — ——————————————— —

ON/OFF

PÉRIPHÉRIQUES

ON/OFF DEVICE

——— — ——————————————— —

ON/OFF

PÉRIPHÉRIQUES

ON/OFF DEVICE

——— — ——————————————— —

ON/OFF

PÉRIPHÉRIQUES

WIRE NUT / ON/OFF DEVICE

——— — —————————————————————————————— —

FILS TORSADÉS / ON/OFF

PÉRIPHÉRIQUES

WIRE NUT

——— — ——————————————— —

FILS TORSADÉS

TRANSFORMER

——— —— —————————————————— —

TRANSFORMATEUR

SPT-3 CORDSET

——— —— ——————————————— —

CORDON SPT-3

WHITE (BLANC)

BLACK (NOIR)

MOTOR

————— —————

MOTEUR

YELLOW (JAUNE)

RED/WHT (ROUGE/BLANC)

YELLOW

JAUNE

WHITE

BLANC

BLACK

NOIR

RED/WHT

ROUGE/BLANC

TRANSFORMER

——— —— —————————————————— —

TRANSFORMATEUR

24 VOLTS

MOTOR

————— —————

MOTEUR

AUTO FAN

——— —— ——————————— —

VENTILATEUR

AUTO

120 VOLTS

BLACK

NOIR

RED/WHT

ROUGE/BLANC

LOW VOLTAGE (BAS VOLTAGE)

120 VOLTS

JUNCTION BOX

—— —— ——— —————————————— ——

BOÎTE DE JONCTION

RED/WHT

ROUGE/BLANC

GAS VALV E

——— —— ————————————— —

VALVE DE GAZ

BLACK (NOIR)

RED/WHT (ROUGE/BLANC)

LIMIT CONTROL

——— — ——————————————— —

CONTRÔLE

LIMITE

WIRING DIAGRAM

————————————————————

CÂBLAGE DE DIAGRAMME

AUTO FAN

——— —— ——————————— —

VENTILATEUR

AUTO

IF ANY OF THE ORIGINAL WIRE AS SUPPLIED

WITH THIS UNIT MUST BE REPLACED, IT MUST

BE REPLACED WITH 150°C THERMOPLASTIC

4/64 THICK OR ITS EQUIVALENT.

120V. 60Hz. LESS THAN 3 AMPS

S´IL YAUN FIL ORIGINAL FOURNI AVEC

L´APPAREIL QUI DOIT ÊTRE REMPLACÉ. IL DOIT

ÊTRE REMPLACÉ AVEC UN ÉQUIVALENT À FIL

4/64” THERMOPLASTIQUE 150°C.

120V. 60Hz. MOINS DE 3 AMPS.

—————— ———————————————————————————————————————————————

LADDER WIRING DIAGRAM

——————————————————————————

ÉCHELLE ÉLECTRIQUE

SCHÉMATIQUE

BLK (NOIR)

GRN (VERT)

WHT (BLANC)

SPP UNITS

GAS VALV E

——— —— ————————————— —

VALVE DE GAZ

LIMIT CONTROL

——— — ——————————————— —

CONTROL DE

TOLERANCE

BLACK

NOIR

ON/OFF DEVICE

——— — ——————————————— —

ON/OFF

PÉRIPHÉRIQUES

WIRE NUT

—————————————---------------- —

FILS TORSADÉS

ON/OFF DEVICE

——— — ——————————————— —

ON/OFF

PÉRIPHÉRIQUES

WIRE NUT

—————————————---------------- —

FILS TORSADÉS

37402-5-0620 Page 17

SERVICE AND MAINTENANCE SUGGESTIONS

GENERAL: All furnaces have been re-tested to check for proper

operation. This includes, main burner ame, pilot ame, fan op-

eration, fan control, limit control and automatic valve operation. If

the furnace fails to function on initial installation, it is advisable to

re-check the following:

1. 115 volts to the junction box.

2. Inlet gas pressure.

3. The 24 volt system.

4. Type of gas being used and that shown on the rating label.

Standing Pilot Model

Servicing the Pilot and Main Burners, Pilot Orice, Thermo-

couple, and Main Burner Orices: Disconnect the gas supply at

the inlet to the control valve. Then remove the burner door to gain

access to the above listed components.

If Electrode Does Not Produce Spark:

1. Check wire connections.

2. Check gap for pilot burner to the electrode tip. Should be

between 1/8” (3mm) and 3/16” (4.8mm). Electrode wire and

tip must be more than 1/4” (6.3mm) away from all other metal

components.

If Pilot Does Not Light By Any Means:

1. Check valve knob for being in the “Pilot” position.

2. Check pilot adjustment for being full open (counterclockwise

to open).

3. If gas is available in the supply tubing, the pilot orice and/or

pilot burner is probably restricted by a spider web. Clean pilot

assembly and relight.

If Pilot Does Not Remain On After Releasing Knob:

1. Follow instructions and hold button down longer and harder.

2. Determine if pilot ame extends past thermocouple; if not, adjust

input or clean pilot burner.

3. Replace thermocouple if millivolts read less than 15 millivolts.

Pilot Outage During Normal Operation:

Check air inlet tube for a good tight t at both ends (6” diameter

tube).

2. Check burner door and pilot hole cover for tight seal.

3. Check input by manifold pressure gauge or gas meter.

Main Gas Valve Does Not Open when ON/OFF Device Is

Turned To On:

1. Check for 24 volts to valve by removing one wire and touching

to the SAME TERMINAL it was on. Terminal should have a

light spark.

2. To check for line voltage to furnace, remove front panel and

short across two-terminal fan control to allow fan to operate.

Cleaning Combustion (Exchanger) Assembly

A QUALIFIED SERVICE PERSON should remove the combustion

(exchanger) assembly and ue bafes. Apply air pressure to the

inside of the combustion (exchanger) assembly and ue bafes in

order to clear all passageways.

Oiling the Motor

The Fan motor should be cleaned and oiled once each heating

season. Oil holes are located on the top at each end of the mo-

tor. Use a few drops of #10 motor oil. To clean the motor, blow

air through its ventilation openings with a vacuum cleaner or low

pressure air source.

37402-5-0620Page 18

START

System Check

Trial for

Ignition

Main Burner

Operation

END



Pilot Valve Opens

Ignitor Powered

Flame Signal

Detected

Call for Heat



Ignitor OFF

Main Valve Opens

Internal Check

Pilot Light and Flame is

Sensed During Trial For

Ignition (1)

Apply 24 VAC

To Appliance

Main Pilot Valves

Call for Heat Ends

Flame Signal

Lost?



Pilot Valve Ignition OFF

Wait for Flame Signal to

Disappear



Pilot Valve Closes

Ignition OFF

Main Pilot

Valves Close

Flame Lost More

Than 5Times in

One Call for Heat

5 Minute Retry Delay

3 Second Flame Recycle

Delay

YES

(1) Ignitor will turn OFF about 30 seconds into the trial for ignition if the pilot flame has not lit. It will turn back ON for the final 30 seconds

of the 90 second trial for ignition. The pilot valve will be energized during the entire trial for ignition. This is normal operation for this gas

ignition system.

DVC-35IP INTERMITTENT PILOT SEQUENCE OF OPERATION

(1) Ignitor will turn OFF about 30 seconds into the trial for ignition if the pilot ame has not lit. It will turn back ON for the nal 30

seconds of the 90 second trial for ignition. The pilot will be energized during the entire trial for ignition. This is normal operation

for this gas ignition system.

37402-5-0620 Page 19

START

IP SYSTEM TROUBLESHOOTING SEQUENCE

Turn OFF Gas Supply

Disconnect System Control

Harness

Set Thermostat to Call for

Heat

Check for Proper Voltage at

Control Harness (See Inset A-

Vo ltageShouldbe 24V

Between Thermostat and 24V

Common, and 24V Between

24V Common and 24V Hot.)

Plug Harness into SmartValve

Control

Wait for Internal Check Delay

(SV9501)

Igniter Warms UP and Glows

Red

Note: Igniter Will Cycle OFF

and Back ON Once During the

90 Second Ignition Trial

Turn On Gas Supply

Pilot Burner Lights

Main Valve Opens and

Main Burner Lights

System is Okay

Check

Line Voltage Power

Low Voltage Transformer

Limit Controller

Thermostat

Wiring

Unplug Pilot Burner Cable.

Measure Voltage at SmartValue HSI

Element Output (See Inset B) 24V

Nominal

Replace Igniter/Flame Rod

Assembly

Reconnect Pilot Burner Cable

Check that Pilot Gas is Flowing

Wait to Assure Pilot Gas Tubing is

Purged.

Measure Voltage Between 24V Hot

and 24V Common Leads to

SmartValve Control. Must Measure

at Least 19.5 VA C with Igniter

Powered. See InsetAto Identify

Proper Lead. This Check Must be

Done with the SmartValve Control

Connected and Igniter Powered.

Replace Igniter/Flame Rod

Assembly

Check that Pilot Flame Makes

Good Contact with Pilot Burner

Flame Rod

Check for Good Electrical

Connection Through the Pilot

Tubing

If Both of the Above are Good,

Replace Igniter/Flame Rod

Cycle Thermostat OFF and Back

Main Burner Lights

YES

Replace SmartValve Control

Reconnect Pilot Burner Cable

Replace SmartValve Control

Check Transformer and Line Volt

Supply

Replace SmartValve Control

SmartValve System Troubleshooting Sequence

Note: Before Troubleshooting, Become Familiar

with the Sequence of Operation

INSET A

24 Volt

Thermostat

Volts

24 Volt

Common

Volts

24 Volt

Hot

EFT

Output

End View

of Control

Harness

Connector

INSET B

HSI

Terminals

DVC-35IP INTERMITTENT PILOT SYSTEM TROUBLESHOOTING SEQUENCE

HSI

Terminals

INSET B

End View

of Control

Harness

Connector

EFT

Output

24 Volt

Hot

Volts

24 Volt

Common

Volts

24 Volt

INSET A

37402-5-0620Page 20

PARTS LIST

PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.

INDEX

PART

DESCRIPTION

1 DV1213 TOP PLATE

2 R3165 DOOR CLIP (2 REQUIRED)

3 39476 CASING SIDE - RIGHT

4 DV1202 CASING BACK

5 39476 CASING SIDE - LEFT

6 DV1249 AIR DROP

7 DV1230 TURBULATOR (3 REQUIRED)

8 DV1233 OUTLET BOX REAR

9 DV1224 OUTLET BOX COVER

10 R3161 FAN BLADE

11 R3166 FAN MOTOR

12 DV1246 MOTOR MOUNTING BRACKET

13 R1536 BUSHING

14 R1499 RUBBER GROMMET (4 REQUIRED)

15 R1454 BRASS BUSHING (4 REQUIRED)

16 R3164 DOOR CLIP (2 REQUIRED)

17 DV1251

INNER SHIELD - RIGHT

(INCLUDES NO. 21)

18 R6176 FAN CONTROL SWITCH

19 R3175 LIMIT SWITCH

20 DV1255 INNER SHIELD FRONT (SPP)

20 15666 INNER SHIELD FRONT (IP)

21 DV1253

INNER SHIELD COVER PLATE

(2 REQUIRED)

22 DV1252

INNER SHIELD - LEFT

(INCLUDES NO. 21)

23 DV1257 EXCHANGER ASSEMBLY

24 R3162 FILTER

25 R3163 FILTER RETAINER

26 R3232 PILOT - NATURAL (IP ONLY)

26 R3233 PILOT - PROPANE (IP ONLY)

27 P8852 ORIFICE - NATURAL (3 REQUIRED)

27 P8861 ORIFICE - PROPANE (3 REQUIRED)

28 DV1236 MANIFOLD

29 DV1259 CASING FRONT

30 P112 MANIFOLD UNION

31 R1109 BUSHING (3/8 X 1/2)

31 R9505 BUSHING (1/2 X 3/4) - NATURAL (IP)

32 R3170 GAS VALVE - NATURAL (IP)

32 R3171 GAS VALVE - PROPANE (IP)

32 R2148 GAS VALVE - NATURAL (SSP)

32 R5655 GAS VALVE - PROPANE (SPP)

33 R2708 PIEZO IGNITOR (SPP)

34 DV781

OBSERVATION HOLE COVER WITH

MICA

35 M155 GASKET - OBS HOLE

36 FF160 PIEZO BRACKET (SPP)

37 DV1240 BURNER COMPARTMENT FRONT

38 DV12655 BURNER COMPARTMENT BODY

39 M147 GASKET - TUBE SEAL

40 DV775 SEAL BRACKET (SPP)

40 DV691 SEAL BRACKET (IP)

41 M156 MANIFOLD GASKET

42 DV1235 PILOT BRACKET (IP)

43 R3031 BURNER (3 REQUIRED)

44 DV1239 BURNER BRACKET

45 UH810

TRANSFORMER MOUNTING

BRACKET (SPP)

45 UH452

TRANSFORMER MOUNTING

BRACKET (IP)

46 R1995 TRANSFORMER (SPP)

46 R998 TRANSFORMER (IP)

47 UH451 JUNCTION BOX COVER

48 DV572 JUNCTION BOX

49 R1410 BUSHING

50 R690 CORD SET

51 R1515 BUSHING

52 DV1215 BOTTOM PLATE

53 R3034 PILOT - NATURAL (SPP)

53 R3035 PILOT - PROPANE (SPP)

54 GWT021 PILOT BRACKET (SPP)

55 R3180 ELECTRODE AND WIRE (SPP)

56 R2256 THERMOCOUPLE - 18” (SPP)

58 DV1273 VENT KIT COMPLETE

59 DV1355 FLUE OUTLET TUBE

60 DV1354 AIR INLET TUBE

61 DV131 OUTSIDE MOUNTING PLATE

62 DV769 VENT CAP

N/S DV1261 PILOT TUBING W/FERRULES

N/S R1081 PILOT ORIFICE - NATURAL (SPP)

N/S R1089 PILOT ORIFICE - PROPANE (SPP)

N/S R1233 PILOT ORIFICE - NATURAL (IP)

N/S R3265 PILOT ORIFICE - PROPANE (IP)

N/S R3172 WIRE HARNESS (SPP)

N/S R3173 WIRE HARNESS (IP)

N/S R3236 WIRE (IP)

N/S - NOT SHOWN

INDEX

PART

DESCRIPTION

USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.

La page charge ...

Empire Direct-Vent Wall Counterflow Le manuel du propriétaire

Marque: Empire

Modèle: Direct-Vent Wall Counterflow

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Empire Direct-Vent Wall Counterflow Owner's manual

Empire Direct-Vent Wall Counterflow Le manuel du propriétaire

Ce manuel convient également à

Empire Direct-Vent Wall Counterflow Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents