Delta S36-290 Le manuel du propriétaire

Taper
Le manuel du propriétaire

Ce manuel convient également à

S36-290
To reduce the risk of serious injury, thoroughly read and comply with all warnings and instructions in this manual and on product
KEEP THIS MANUAL NEAR YOUR PRODUCT FOR EASY REFERENCE AND TO INSTRUCT OTHERS
www.shopmastermachinery.com
INSTRUCTION MANUAL
10 IN. PORTABLE TABLE SAW WITH STAND
SPANISH TRANSLATION (PG 54)
FRENCH TRANSLATION (PG 28)
MANUAL DE INSTRUCCIONES
SIERRA DE MESA PORTÁTIL DE
10" CON BASE
GUIDE D’UTILISATION
SCIE À TABLE PORTATIVE AVEC
SUPPORT DE 10PO (25,4CM)
2
The SHOPMASTER S36-290 10-inch Portable Table
Saw is designed to help you achieve your home
improvement and home shop needs. This saw can
tackle nearly any DIY project with easy to use features.
This saw package contains the following items: Saw
Assembly, Stand, Rip Fence, Miter Gauge, Push Stick,
Riving knife, Anti-kickback Pawls, Blade guard, Throat
Plate, and 10-in. carbide tooth blade.
NOTE: The manual cover illustrates the current production model. All other illustrations contained in the manual are
representative only and may not be exact depictions of actual labeling or accessories included. They are intended for
illustrative purposes only.
FUNCTIONAL DESCRIPTION ............................................... 2
IMPORTANT SAFETY INSTRUCTIONS ................................ 3
SAFETY SYMBOLS-DEFINITIONS ....................................... 3
GENERAL SAFETY RULES ................................................... 3
PROPOSITION 65 WARNING ................................................ 4
TABLE SAW SAFETY RULES ................................................ 4
TERMINOLOGY .................................................................. 4
TABLE SAW SPECIFIC SAFETY RULES ............................. 5
MAKING A PUSH STICK..................................................... 6
KICKBACKS ........................................................................ 6
POWER CONNECTIONS ....................................................... 7
POWER SOURCE ............................................................... 7
EXTENSION CORDS ........................................................... 7
UNPACKING ........................................................................... 8
SHIPPING CONTENTS ....................................................... 8
HARDWARE BAG CONTENTS ........................................... 9
TOOLS NEEDED FOR ASSEMBLY OF ADJUSTMENTS .... 9
GENERAL PARTS KNOWLEDGE ........................................ 10
ASSEMBLY ........................................................................... 10
STAND ASSEMBLY ........................................................... 10
ATTACHING STAND TO SAW ........................................... 12
HEIGHT ADJUSTMENT KNOB INSTALLATION ................ 12
INSTALLING/CHANGING BLADE ..................................... 13
POSITION THE RIVING KNIFE .......................................... 13
INSERT AND LEVEL THROAT PLATE ............................... 14
ANTI-KICKBACK PAWLS AND BLADE GUARD ............... 14
RIP FENCE ........................................................................ 15
OPERATION .......................................................................... 16
TURNING THE SAW ON AND OFF ................................... 16
CIRCUIT BREAKER SAFETY AND INSTRUCTION ........... 17
MAKING CUTS ..................................................................... 17
RIP CUTS .......................................................................... 18
BEVEL RIPPING ................................................................ 18
CROSSCUTTING .............................................................. 19
BEVEL CROSSCUTTING .................................................. 19
MITER CROSSCUTTING .................................................. 19
COMPOUND MITER CUTS............................................... 20
LARGE PANEL CUTS ........................................................ 20
NON-THROUGH CUTS .................................................... 20
MAKING A NON-THROUGH CUT .................................... 20
CUTTING AIDS AND ACCESSORIES ................................. 21
PUSH STICK ..................................................................... 21
AUXILIARY MITER GAUGE FACING ................................. 21
PUSH BLOCK ................................................................... 22
FEATHERBOARD .............................................................. 22
CUT OFF GAUGE ............................................................. 23
JIGS .................................................................................. 23
MAKING ADJUSTMENTS .................................................... 23
LEVELING THE THROAT PLATE ....................................... 23
CHANGING THE BEVEL ................................................... 23
ADJUSTING THE BEVEL STOPS ..................................... 24
ADJUSTING THE BLADE HEIGHT .................................... 24
USING THE MITER GAUGE .............................................. 24
RIVING KNIFE ADJUSTMENT ............................................. 25
RIVING KNIFE ALIGNMENT.............................................. 25
MAINTENANCE .................................................................... 26
TROUBLESHOOTING .......................................................... 26
ACCESSORIES ..................................................................... 27
PARTS, SERVICES OR WARRANTY ASSISTANCE ........... 27
REPLACEMENT PARTS .................................................... 27
FREE WARNING LABEL REPLACEMENT ........................ 27
SERVICE AND REPAIRS ................................................... 27
FRENCH ............................................................................... 28
SPANISH ............................................................................... 54
MAX DEPTH OF CUT AT 90°:
3"
MAX DEPTH OF CUT AT 45°:
2-
1
/
2
"
MAX RIP TO RIGHT OF BLADE:
12"
MAX RIP TO LEFT OF BLADE:
8"
Motor specications:
AMPERAGE:
15 Amps
VOLTAGE:
120 Volts
SPECIFICATIONS
TABLE OF CONTENTS
FUNCTIONAL DESCRIPTION
3
SAFETY SYMBOLS- DEFINITIONS
This manual contains information that is important for you to know and understand. This information relates to
protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we
use the symbols below. Please read the manual and pay attention to these sections.
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided,
may result in property damage.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAREFULLY READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS ON YOUR
PRODUCT AND IN THIS MANUAL. SAVE THIS MANUAL. MAKE SURE ALL USERS
ARE FAMILIAR WITH ITS WARNINGS AND INSTRUCTIONS WHEN USING THE TOOL. Improper operation,
maintenance or modication of tools or equipment could result in serious injury and/or property damage.
GENERAL SAFETY RULES
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
y READ INSTRUCTION MANUAL AND KNOW YOUR
TOOL. Read and familiarize yourself with the entire
instruction manual. Learning the tool’s proper
applications, limitation, and specic potential hazards
will greatly minimize the possibility of accidents and
injury. Make sure all users are familiar with its warnings
and instructions before using.
y MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
y KEEP GUARDS AND SAFETY DEVICES IN PLACE
and working properly.
y CHECK TOOLS FOR DAMAGE. Before using, and
after tool or accessory has been dropped or damaged,
check guards and affected parts, for alignment,
breakage and any other condition that may affect
its operation to make sure tool will operate properly
and all parts will perform their intended function. Do
not use a damaged product. A guard or any other
part that is damaged should be properly repaired or
replaced using factory approved service parts.
y NEVER STAND ON TOOL. Serious injury could occur
if the tool tips or if you unintentionally contact the
cutting surface.
y WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Nonslip
protective footwear is recommended. Wear protective
hair covering to contain long hair.
y WEAR PROPER EYE PROTECTION. All persons
in work area should wear safety glasses with side
shields. Everyday eye glasses with impact resistant
lenses are not safety glasses. Eye equipment should
comply with ANSI Z87.1 standards.
y WEAR PROPER HEARING PROTECTION. All people
in work area should wear proper hearing protection
consistent with noise levels and exposure. Hearing
equipment should comply with ANSI S3.19 standards.
y DUST PROTECTION. Use of power tools can
generate and/or disburse dust, which may cause
serious or permanent respiratory or other injury,
including silicosis (a serious lung disease), cancer,
and death. Direct particles away from face and body.
Always operate tool in a well-ventilated area and
provide for proper dust removal. Use dust collection
system whenever possible. Avoid breathing dust and
avoid prolonged contact with dust. Allowing dust to
get into your mouth or eyes, or lay on your skin may
promote absorption of harmful material. Use properly
tting NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure and wash exposed
areas with soap and water.
y LOCK TOOLS AND WORK AREA. Use padlocks, and
master switches, or remove and store starter keys to
prevent operation by children and other unauthorized
users.
y DO NOT USE OR STORE TOOL IN DANGEROUS
ENVIRONMENTS. Exposure to rain and damp or
wet locations can result in shock or electrocution,
or damage the tool. Do not operate electric tools
near ammable liquids or in gaseous or explosive
atmospheres. Motors and switches in these tools may
spark and ignite fumes.
y KEEP WORK AREA CLEAN AND WELL LIT. Cluttered
and poorly-lit work areas, surfaces and benches can
lead to accidents.
y KEEP CHILDREN AND BYSTANDERS AWAY from
work area.
y USE RECOMMENDED ACCESSORIES. Consult
manual for recommended accessories. Use of
inappropriate accessories may cause personal injury
or property damage.
y DISCONNECT TOOL from power source before
servicing, adjusting or changing set-ups or blades,
bits, cutters and other accessories.
y TO REDUCE RISK OF ACCIDENTAL STARTING make
sure power switches are in “OFF” position before
plugging tool in.
y TO REDUCE THE RISK OF ELECTRIC SHOCK, this
equipment has a polarized plug (one blade is wider
than the other). This plug will t in a polarized outlet
only one way. If the plug does not t fully in the
IMPORTANT SAFETY INSTRUCTIONS
4
outlet, reverse the plug. If it still does not t, contact
a qualied electrician to install the proper outlet. Do
not change the plug in any way.
y DO NOT touch the plug’s metal prongs when
unplugging or plugging in the cord.
y USE PROPER EXTENSION CORD. If you use an
extension cord, make sure it is in good condition and
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating.
See Extension Cord Chart for correct size depending
on cord length and data plate ampere rating. If in
doubt, use the next smaller gauge number. The
smaller the gauge number, the heavier the cord.
When working outside, make sure the extension cord
is rated for outdoor use. Consult power connection
section of this manual for Extension Cord Chart and
power connection safety.
y DO NOT ABUSE POWER CORDS. NEVER yank
cord to disconnect from receptacle, crush cord, or
expose it to heat, oil or sharp objects.
y USE PROPER TOOL. Do not force tool to do a task
for which it was not designed.
y SECURE WORKPIECE. Use clamps or a vise to hold
the workpiece when practical. It is safer than using
your hands and frees both hands to operate tool.
y REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that all adjusting keys
and wrenches are removed before starting tool.
y STAY ALERT, WATCH WHAT YOU ARE DOING,
AND USE COMMON SENSE. Do not use power
tools when tired or under the inuence of drugs,
alcohol, or medication. A moment of inattention while
operating power tools may result in injury.
y USE PROPER FEED DIRECTION. Feed workpiece
against the direction of rotation of the tool’s blade,
cutter, or abrasive surface. Feeding in the other
direction may cause the workpiece to be thrown at
high speed.
y DO NOT OVERREACH. Keep proper footing and
balance to maintain control.
y DO NOT FORCE TOOL OR WORKPIECE. Operate
tool at intended speed and feed rate for better and
safer operation.
y NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Do not leave tool until it comes
to a complete stop. In the event of a power failure,
move switch to “OFF” position.
y SERVICE PARTS. Use only identical replacement
parts when servicing your tool.
GENERAL SAFETY RULES
THE FOLLOWING TERMS WILL BE USED THROUGHOUT THE MANUAL AND YOU SHOULD BECOME
FAMILIAR WITH THEM.
y THROUGH-CUT - any cut that completely cuts
through the workpiece.
y NON-THROUGH CUT - any cut that does not
completely cut through the workpiece.
y PUSH STICK - a wooden or plastic stick, usually
homemade, that is used to push a small workpiece
through the saw and keeps the operator’s hands clear
of the blade.
y KICKBACK - when the saw blade binds in the cut or
the workpiece binds between the blade and the fence
and the workpiece is thrust back toward the operator.
y FREEHAND - cutting without the use of a miter gauge
or rip fence or any other means of guiding or holding
the workpiece other than the operator’s hand.
y PLUNGE CUTTING - blind cuts in the workpiece
made by either raising the blade through the
workpiece or lowering the workpiece down to the
blade.
y RE-SAWING - ipping the workpiece to complete a
cut the saw is not capable of making in one pass.
y COVE CUTTING - an operation where the work is fed
at an angle across the blade. (Also known as “coving”)
TERMINOLOGY
Dust created by power sanding, sawing, grinding, drilling, and other construction activities may contain chemical
known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples are:
y Lead from lead-based paints
y Crystalline silica from bricks and cement and other masonry products
y Asbestos dust
y Arsenic and chromium chemically-treated lumber
Your risk from these exposures varies depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well-ventilated area and with approved safety equipment, such as dust masks that are
specically designed to lter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities.
Wear protective clothing and wash exposed areas with soap and water.
If you have any questions or concerns relative to the use of your tool or the contents of this manual, stop using the
tool and call Delta Power Equipment Company Customer Care at 1-800-223-7278.
PROPOSITION 65 WARNING
TABLE SAW SAFETY RULES
5
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
y SEE GENERAL POWER TOOL SAFETY SECTION OF THIS MANUAL. Read entire instruction manual before
operating saw. Learning the saw’s proper applications, limitations, and specic potential hazards will greatly
minimize the possibility of accidents and injury. Make sure all users are familiar with its warnings and instructions
before using saw.
y SEE POWER CONNECTION SECTION OF THIS MANUAL for instructions and warnings regarding power cords
and connections.
y AVOID KICKBACK. Pay particular attention to the
instructions (below) for reducing risk of kickback.
y OBTAIN ADVICE from your supervisor, instructor,
or another qualied person if you are not thoroughly
familiar with the operation of this machine.
Knowledge is safety.
y DRESS PROPERLY. Wear appropriate apparel, eye
protection, hearing protection and dust protection
as specied in the General Power Tool Safety
Section of this manual.
y PROPER ASSEMBLY. Do not operate this saw until
it is completely assembled and installed according
to the instructions.
y STABILITY. Make sure table saw is properly
assembled and located on a stable surface before
use to keep saw from moving during cut. Do not
attempt the substitute a table or other surface for
the leg assembly.
y USE CORRECT BLADE AND RIVING KNIFE for
the intended operation. The blade must be installed
so the points of the teeth are pointing toward the
front of the saw. Do not use oversized blade or
blade with incorrect arbor opening. Always tighten
the blade arbor nut securely. Before use, inspect
the blade for cracks or missing teeth. Do not use
a damaged or dull blade. Always use blade within
the thickness range for which the riving knife is
designed.
y USE PROPER THROAT PLATE. The proper throat
plate must be in place and properly secured at all
times to reduce the risk of a thrown workpiece and
possible injury.
y USE SAW BLADE GUARD, RIVING KNIFE
AND ANTI-KICKBACK PAWLS. Your saw is
equipped with a modular blade guard, riving
knife and anti-kickback pawl assembly. Each
of these components should be used for every
possible operation, including all through cuts. This
assembly is discussed in more detail below. Make
sure components are securely installed prior to
operation.
y NEVER CUT METALS, CEMENT BOARD OR
MASONRY. Certain man-made materials have
special instructions for cutting on table saws. Follow
the manufacturer’s recommendations at all times.
y SUPPORT YOUR WORKPIECE based on its
size and the type of operation to be performed.
Hold the workpiece rmly against the fence
and down against the table surface. Do not
attempt to cut a wide panel or long board which
hangs, unsupported, beyond the end of the
table surface. The weight of a workpiece, if not
properly supported, may causes it to shift on the
table resulting in loss of control. An unsupported
workpiece which hangs beyond the table surface
may pinch the blade during a cut, which leads to
kickback.
y NEVER PERFORM LAYOUT, ASSEMBLY OR SET-
UP WORK ON THE TABLE/WORK AREA when the
saw is running.
y USE A PUSH STICK that is appropriate to the
application to push and hold down a workpiece
through the completion of the cut. A push stick is
a wooden or plastic stick, usually homemade, that
should be used whenever the size or shape of the
workpiece would cause you to place your hands
within 6 in. (152 mm) of the blade. Instructions for
making a push stick are included in this manual. A
push stick is also provided with this saw.
y NEVER Perform freehand cutting, plunge cutting,
re-sawing, or cove cutting.
y CHECK WORKPIECE AND SET-UP before each
operation. Knots, irregularities, or nails in workpiece
and positioning mistakes or incomplete set-up
may interfere with or affect saw performance and
personal safety.
y NO FREEHAND CUTS. Always use a rip fence,
miter gauge, or other appropriate devices to guide
or hold down the workpiece. Use hold-downs, jigs,
xtures or feather boards to help guide and control
The workpiece. Accessories for use with your saw
are available at extra cost from your local dealer or
authorized service center.
y DO NOT USE RIP FENCE AND MITER GAUGE AT
THE SAME TIME.
y AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause
a hand to move into a saw blade. Operate with
table at or near waist level for maximum balance
and control. Anticipate effect of workpiece size on
your ability to adjust position and maintain control
through completion of cut.
y KEEP ARMS, HANDS AND FINGERS AT LEAST
SIX INCHES AWAY FROM THE BLADE.
y KEEP HANDS AND OTHER BODY PARTS OUT
OF THE BLADE PATH. NEVER have any part of
your body in line with the path of the saw blade.
y NEVER START THE SAW WITH THE WORKPIECE
AGAINST THE BLADE to reduce the risk of a
thrown workpiece.
y DO NOT REACH OVER/REACH AROUND. Never
reach over, in back of, or around the cutting tool with
either hand while the blade is in motion.
y NEVER ATTEMPT TO FREE A STALLED BLADE OR
TABLE SAW SPECIFIC SAFETY RULES
TABLE SAW SAFETY RULES
6
In order to operate your table saw safely, you must use a
push stick whenever the size or shape of the workpiece
would otherwise cause your hands to be within 6 inches
(152 mm) of the saw blade or other cutter. A push stick is
included with this saw.
No special wood is needed to make additional push
sticks as long as they are sturdy and long enough and
the wood is free of knots, checks and cracks. A length of
16 inches (400 mm) is recommended with a notch that
ts against the edge of the workpiece to prevent slipping.
It’s a good idea to have several push sticks of the same
minimum length, 16 inches (400 mm), with different size
notches for different workpiece thicknesses.
The shape can vary to suit your own needs as long as
it performs its intended function of keeping your hands
away from the blade. Angling the notch so the push stick
can be held at a 20- to 30-degree angle from the saw’s
table will help you to hold down the workpiece while also
moving it through the saw. Refer to diagram in cutting
aids section of this manual.
MAKING A PUSH STICK
SAW BLADE GUARD, ANTI-KICKBACK PAWLS AND RIVING KNIFE
ASSEMBLY
KICKBACKS
Kickbacks can cause serious injury. A kickback occurs
when a part of the workpiece binds between the saw blade
and the rip fence, or other xed object, rises from the table
and is thrown toward the operator. The risk of kickback
can be minimized by attention to the following instructions.
HOW TO REDUCE THE RISK OF KICKBACKS AND
PROTECT YOURSELF FROM POSSIBLE INJURY:
y Be certain that the rip fence is parallel to the saw
blade.
y DO NOT rip by applying the feed force to the section
of the workpiece that will become the cut-off (free)
piece. Feed force when ripping should always be
applied between the saw blade and the fence; use
a push stick for all narrow work that is 6 inches (152
mm) wide or less.
y Keep saw blade guard, riving knife and anti-kickback
assembly in place and operating properly. The riving
knife must be in alignment with the saw blade and the
anti-kickback assembly must stop a kickback once
it has started. Check their action before ripping by
pushing the wood under the anti-kickback assembly.
The teeth must prevent the wood from being pulled
toward the front of the saw. If any part of assembly
is not operational, return to the nearest authorized
service center for repair.
y Plastic and composite materials (like hardboard) may
be cut on your saw. However, since these are usually
quite hard and slippery, the anti-kickback pawls may
not stop a kickback. Therefore, be especially attentive
to following proper set up and cutting procedures for
ripping.
y Use saw blade guard, anti-kickback pawls, and riving
knife assembly for every possible operation, including
all through-cut sawing.
y Push the workpiece past the saw blade prior to
releasing control.
y NEVER rip a workpiece that is twisted or warped,
or does not have a straight edge to guide along the
fence.
y NEVER saw a large workpiece that cannot be
controlled.
y NEVER use the fence as a guide or length stop when
crosscutting.
y NEVER saw a workpiece with loose knots, aws, nails
or other foreign objects.
y NEVER rip a workpiece shorter than 10 inches (254
mm).
y NEVER use a dull blade. A dull blade should be
replaced or re-sharpened.
Your table saw is equipped with a blade guard, anti-
kickback pawls and riving knife assembly that covers
the blade and reduces the possibility of accidental blade
contact. The riving knife is a at plate that ts into the
cut made by the saw blade and effectively prevents
kickback by lessening the tendency of the blade to bind
in the cut. Two anti-kickback pawls are located on the
sides of the riving knife that allow the wood to pass
through the blade in the cutting direction but reduce
the possibility of the material being thrown backwards
toward the operator. The riving knife can be used in two
positions. It must be raised to the through-cut position
before attaching anti-kickback pawls and blade guard.
Both positions are marked on the riving knife. The blade
guard and anti-kickback pawls can only be used when
making through cuts that sever the wood. When making
rabbets and other non-through cuts, the blade guard and
anti-kickback pawls must be removed and riving knife
lowered to the non-through cut position marked on the
riving knife.
Use all components of the guarding system (blade
guard assembly, riving knife and anti-kickback pawls)
for every operation for which they can be used including
all through-cutting. If you elect not to use any of these
components for a particular application, exercise
additional caution regarding control of the workpiece, the
use of push sticks, the position of your hands relative to
the blade, the use of safety glasses, the means to avoid
kickback and all other warnings contained in this manual
and on the saw itself. Replace the guarding systems as
soon as you return to through-cutting operations. Keep
the guard assembly in working order.
TRAPPED WORKPIECE without rst turning the saw off and disconnecting the saw from the power source.
y BEFORE LEAVING THE SAW, wait for the blade to come to a complete stop, then disconnect the saw from the power
source, clean the table and work area, and lock out switch to prevent unauthorized use.
y AN UNFAMILIAR NOISE OR EXCESSIVE VIBRATION may indicate a problem with your saw. If this happens, turn
it off and disconnect it from the power source until the problem has been located and corrected. Contact customer
service for assistance if the problem cannot be solved.
TABLE SAW SAFETY RULES
7
POWER CONNECTIONS
This saw is equipped with a 15-amp motor for use with a
120-volt, 60-HZ alternating current. See instructions below
regarding proper connections for your saw. For voltage,
the wiring in a shop is as important as the motor’s rating.
A line intended only for lights may not be able to properly
carry the current needed for a power tool motor; wire that
is heavy enough for a short distance may be too light for
a greater distance; and a line that can support one power
tool may not be able to support two or three.
A separate electrical circuit should be used for your
machines. This circuit should not be less than #12 wire
and should be protected with a 20-amp time lag fuse.
Before connecting the machine to the power line, make
sure the switch is in the “OFF” position and be sure that
the electric current is of the same characteristics as
indicated on the machine. A substantial voltage drop will
cause a loss of power and overheat the motor. It may also
damage the machine.
POWER SOURCE
EXTENSION CORDS
Never use a damaged extension cord.
Check extension cords before each use.
If damaged, replace immediately. Touching the damaged
area could case electrical shock resulting in serious injury.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
Keep the extension cord clear of the
work area. Position the cord so it will
not get caught on lumber, tools or other obstructions.
y Use the “MINIMUM GAUGE EXTENSION CORD”
table, show on the right, to determine the proper
length and gauge for any extension cord used to
supply power to your tool.
y Use properly rated extension cords. When using an
extension cord, be sure to use one heavy enough
to carry the current required by your machine. An
undersized cord will cause a drop in line voltage,
resulting in loss of power and overheating. The
table shows the minimum gauge to use depending
on the cord length. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier
the cord. Only round, jacketed cords listed by
Underwriter’s Laboratories (UL) should be used.
y When working outdoors, use an extension cord
designed for outdoor use.
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH
STATIONARY ELECTRIC MACHINES
AMPERE
RATING
VOLTS TOTAL
LENGTH OF
CORD IN
FEET
GAUGE OF
EXTENSION
CORD
0-6
0-6
0-6
0-6
120
120
120
120
Up to 25
25-50
50-100
100-150
18 AWG
16 AWG
16 AWG
14 AWG
6-10
6-10
6-10
6-10
120
120
120
120
Up to 25
25-50
50-100
100-150
18 AWG
16 AWG
14 AWG
12 AWG
10-12
10-12
10-12
10-12
120
120
120
120
Up to 25
25-50
50-100
100-150
16 AWG
16 AWG
14 AWG
12 AWG
12-16 120 Up to 25 14 AWG
12-16 120 25-50 12 AWG
12-16 120 GREATER THAN 50 FEET
NOT RECOMMENDED
Save These Instructions.
Refer to them often and use them to instruct others.
If tool is loaned to someone, also loan them these instructions.
8
UNPACKING
A B GED
JIH L
C
K
F
A. Saw
B. Rip Fence
C. Push Stick
D. Anti-Kickback Pawls
E. Riving Knife (preassembled to saw)
F. Blade Guard
G. Throat Plate
H. Stand Part 1
I. Stand Part 2
J. Stand legs (4)
K. Miter Gauge
L. Blade Wrenches
SHIPPING CONTENTS
Prior to tool assembly and use, read
this manual thoroughly to familiarize
yourself with proper assembly, maintenance and safety
procedures.
Check shipping carton and machine for damage
before unpacking. Carefully remove components in
top foam layer. Remove the top layer of foam then
remove all components in the bottom layer of foam.
Lay out all parts on a piece of cardboard or other clean,
at surface. Always check for and remove protective
shipping materials around motors and moving parts. Do
not discard shipping carton and packing materials until
you have carefully inspected the contents, assembled
the machine and are satised that it operates correctly.
Compare package contents to Shipping Contents
List and Hardware Bag List prior to assembly to make
sure all items are present. Carefully inspect parts to
make sure no damage occurred during shipping. If any
parts are missing, damaged or preassembled, do not
assemble. Instead, call Customer Support at 1-800-223-
7278 for assistance.
9
Description (QTY)
a. M8 x 35 mm Carriage Bolt (8)
b. M8 Flat Washer (2)
c. M8 Spacer (2)
d. M8 x 65 mm Hex Socket Head Screw (2)
e. M8 Lock Nut (10)
f. Hand Wheel Shoulder Screw (1)
g. Handle Wheel Knob (1)
h. 4mm Hex/Phillips Wrench (1)
HARDWARE BAG CONTENTS
TOOLS NEEDED FOR ASSEMBLY OR ADJUSTMENTS (Not Supplied)
UNPACKING
c d
fe hg
b
a
Phillips Screwdriver
Straight Edge
Adjustable Wrench
Combination Square
3 mm,4 mm
Hex Key
10
GENERAL PARTS KNOWLEDGE
ASSEMBLY
STAND ASSEMBLY
Assemble stand part 2 (I) through stand part 1 (H) that
has cross support as shown in (Fig. 1). Secure stand
assembly with M8 x 65mm hex socket head screw (d),
M8 spacer (c), M8 washer (b), and M8 lock nut (e). (Fig.
1)
NOTE: M8 spacer (c) is between stand part (H) and (I).
(Fig. 2) for correct stand parts setup.
The part and hardware names and letters correspond to those shown in General Parts Knowledge, Shipping Contents,
and the Hardware Contents.
BEVEL SCALE
BLADE WRENCHES
STAND
ON/OFF
SWITCH
BEVEL
LOCK
HEIGHT
ADJUSTMENT
WHEEL
FENCE RAIL
SCALE
MITER GAUGE
BLADE GUARD
TABLE
RIP FENCE
PUSH STICK
FENCE LOCK
ANTI-KICKBACK PAWLS
THROAT PLATE
RIVING KNIFE
y When lifting saw, hold it close to your body while
lifting. Keep knees bent and lift with your legs, not
your back.
y Fully assemble saw with stand assembly prior to
use.
y Stand assembly is an integral and necessary part of
the support structure for this saw. Do not attempt
to substitute a table or other surface for the stand
assembly.
y Do not modify saw, or create accessories not
recommended for use with this saw.
y Do not connect to power supply until assembly
is complete. Make sure power switch is in “OFF”
position before connecting to power supply.
y Avoid contact with blade teeth. Keep blade stored
or lowered when possible.
FIGURE 1
H
I
d
b
e
c
11
FIGURE 5
FIGURE 4
STYROFOAM
NOTE: Make sure that stand part 1 (H) and stand part 2
(I) are assembled in the proper orientation.
With assembled stand open, attach legs (J) to the stand
using (eight) M8 x 35mm carriage bolts (a) and (eight)
M8 lock nuts (e). Tighten lock nuts to secure legs to
stand (Fig. 3.)
NOTE: Do not over tighten lock nuts.
See nished assembly of stand in (Fig. 4).
NOTE: Before assembling stand to saw, unlock bevel
lock, tilt blade/motor assembly and remove Styrofoam
piece from under saw motor. The bevel lock is the
handle located underneath the blade height adjustment
wheel (Fig. 5).
ASSEMBLY
FIGURE 2
CORRECT INCORRECT
H H
I I
FIGURE 3
a
e
J
12
ASSEMBLY
Saw as assembled (Fig. 7).
ATTACHING STAND TO SAW
Place saw (A) on stand assembly, while aligning the
screw holes in the saw stand with the threaded holes in
the saw base (Fig. 6).
Tighten hex cap screws to secure stand assembly to
saw.
NOTE: Do not over tighten.
A
HEIGHT ADJUSTMENT KNOB
INSTALLATION
y Insert shoulder screw (f) into height adjustment
knob (g) as shown in Fig. 8.
y Tighten shoulder screw with Phillips Screw driver
into Hand Wheel. Height adjustment knob should
rotate freely around shoulder screw when raising or
lowering the blade with the Height Adjustment Hand
Wheel.
g
f
FIGURE 6
FIGURE 7
FIGURE 8
13
ASSEMBLY
SHAFT
WASHER
NUT
INSTALLING/CHANGING BLADE
Ensure riving knife lock lever is in unlocked position
(Fig. 9).
Remove nut and the outer anged washer from shaft
assembly. Place blade on the arbor shaft with the
teeth on the blade pointing toward the front of the saw.
SHOPMASTER logo on the blade will be facing toward
the left side of the saw. Place anged washer on the
shaft with the large side of the washer towards the
blade, then secure blade assembly with nut. (Fig. 9)
Tighten nut with blade wrenches (L) from the on-board
storage area on the right side of the saw. Open end
wrench will t on the arbor shaft between the inner
ange washer and the motor assembly (if necessary,
turn shaft to align ats on the arbor shaft to the wrench).
Closed end wrench will t on the nut. See Fig. 9a.
Return wrenches (L) to on-board storage location.
Return riving knife lock lever to locked position. Return
throat plate (G) making sure to lock tab on rear of throat
plate under table top as shown in Fig. 9b.
POSITION THE RIVING KNIFE
A riving knife is a at plate that ts into the cut made by
the saw blade (the “kerf”). It is intended to reduce the
risk of kickback by holding the kerf open and lessening
the tendency of the workpiece to pinch the blade.
To reduce the risk of serious injury,
y The riving knife must be installed for every "thru cut"
and for every "non-thru cut" unless the riving knife
would interfere with the cut.
y Always use a blade with the correct thickness to
match the riving knife. (0.10” (2.6mm) min. kerf
width and 0.073” (1.85mm) max body thickness)
y The riving knife must be securely positioned in the
“up” or “thru cut” position when using the anti-
kickback pawls and blade guard.
y Make sure the riving knife is properly aligned to the
blade see Riving Knife Alignment section.
Refer to Fig. 10 & 11
This saw is shipped with its riving knife (E) installed in
the lowered or “non-thru cut” position. This riving knife
matches the thickness of the blade that is shipped with
your saw. To install the anti-kickback pawls and the
blade guard assembly, rst raise the riving knife from the
lowered or “non-thru cut” position to the raised or "thru
cut" position, as follows:
1. With the blade assembly to the highest possible
position, carefully reach alongside the blade and
raise the riving knife locking lever up to unlock the
riving knife.
2. Gently move the riving knife to the right to release it
from the lock pins in the riving knife assembly.
3. Slide the riving knife up and forward until you feel
the lock pins engage the riving knife in the “thru
cut” position. When properly aligned in this position,
the “thru cut" position line on the riving knife will be
parallel to and level with the table.
LOCK
LEVER
UP
E
FIGURE 9
FIGURE 10
FIGURE 11
a
a
b
b
L
G
THRU
CUT
POSITION
14
ASSEMBLY
INSERT AND LEVEL THROAT
PLATE
Insert the rear tab of the throat plate (G) (the end with
the wear plates) under the surface of the table, and
snap the front end in place (Fig. 12).
Check that the throat plate is properly adjusted to the
table. Front of throat plate should be level or slightly
below the surface of the table and rear of the throat
plate should be level or slightly above the surface of the
table (Fig. 12).
1. Return the riving knife lock lever to the lock position.
2. Make sure the riving knife is securely installed and
properly aligned with the blade.
NOTE: For "non-thru cuts", lower the riving knife to
the “non-thru cut” position using the same procedure.
In this case the “non-thru cut" position line should be
parallel to and level with the table.
WEAR
PLATE
ANTI-KICKBACK PAWLS
AND BLADE GUARD
If adjustment is needed, remove the throat plate and
adjust the (4) Phillips set screws (Fig. 13) up or down as
needed. Replace throat plate and recheck. Repeat this
process as needed until the throat plate is level.
It is important that the throat plate is
properly adjusted to the table. This ensures that the
work piece is not caught on the throat plate or the table
when feeding the work piece through the blade during a
cut.
Riving knife (E) must be in the Through Cut position
prior to installation of the anti-kickback pawls (D) and
blade guard (F) (Fig. 14 and 15).
Insert the pawl assembly (D) into the middle slot on
the riving knife (E) as shown in (Fig. 14) while pressing
the spring-loaded pin on the right side of the pawl
assembly.
Once inserted, release the spring-loaded pin so that it
pops back in to place (Fig. 14). Ensure that it is locked
in place.
PIN
E
D
FIGURE 12
FIGURE 13
FIGURE 14
15
ASSEMBLY
While holding the blade guard assembly (F) in a vertical
position, as shown in Fig. 15, pull the blade guard
assembly pin all the way up into the rear slot on the
riving knife.
Rotate the blade guard assembly all the way down so
that the arms are parallel to the table (Fig. 15a). Then
lock the blade guard in place by depressing the lock tab
(Fig. 15b).
Do not hold lock tab in the lock position
while installing the blade guard.
After engaging lock tab to lock blade guard in place pull
up on arms to ensure guard is properly locked.
RIP FENCE
Position rip fence (B) over the table as shown in Fig. 16.
Lower the rear end of the rip fence (B) over the back of
the table; then lower the front end (with lock handle )
over the front of rail on the front of the saw. Engage lock
on the rip fence after placing fence in desired location
on the table (Fig. 16).
Do not use rip fence and miter gauge at
the same time without using a cut off block (gauge) as
described in the Cutting Aids and Accessories section
of this manual.
TIGHTENLOOSEN
FIGURE 17
FIGURE 16
FIGURE 15
a
b
PIN
LOCK
TAB
SLOT
ARMS
F
B
Check to ensure that the rip fence is secured to
the table prior to use when making a cut. If needed
adjustments to tighten or loosen rip fence can be made
by adjusting the lock nut on the rear side of the fence
(Fig. 17).
16
OPERATION
TURNING THE SAW ON AND
OFF
The ON/OFF paddle switch is located on the left side of
the front panel of the saw.
To turn the saw ON lift the switch. Press the switch
down to turn the saw OFF (Fig. 18)
When not in use, the saw should be turned off and the
power switch locked out to prevent unauthorized use.
To lock out power switch, use a standard long shackle
lock, with a shackle that is at least 2-
3
/
4
inch (70mm)
long and no more than
9
/
32
-inch (7mm) thick.
Failure to comply with the following warnings may result in serious personal injury.
READ ENTIRE MANUAL. In addition to reading these operating instructions, it is important to read and understand
the entire manual before operating this saw. Follow all applicable instructions regarding assembly, preparation, and
adjustment prior to making any cuts and comply with all safety rules and warnings in this section and elsewhere
throughout this manual.
EACH TIME YOU USE THE SAW, RUN THROUGH
THE FOLLOWING CHECKLIST:
y Are the power source and power connections
adequate for the saw?
y Are the saw and work area free of clutter and by-
standers?
y Is the blade tight and properly aligned?
y Does the riving knife thickness match the blade
requirements?
y Are the blade and riving knife properly aligned?
y Is the operator qualied to make the cut and familiar
with all of the relevant safety rules, warnings and
instructions included in this manual?
y Is the operator and everyone in proximity to the saw
wearing appropriate eye, hearing and respiratory
equipment?
y Are the bevel angle and height adjustment knobs
locked in the proper position?
y Is the blade set at the proper height?
y If ripping, is the rip fence parallel to the blade and
securely locked in position?
y If crosscutting, is the miter gauge knob tight?
y If making through cuts with a standard blade, are
the blade guard riving knife and anti-kickback pawls
properly attached and properly functioning with
both guards contacting the table surface?
y Is there proper clearance and support for the
workpiece as it enters and leaves the blade?
y Are any cutting aids needed? If so, are they in
place, or within reach for proper use?
y The use of attachments and accessories not
approved by the manufacturer may result in injury.
y Replace or sharpen the anti-kickback pawls when
the points become dull.
y Make sure saw is stable and cut can be
accomplished without tipping the saw.
y Never use fence and miter gauge together without
using a cut off block (gauge) as described in
the Cutting Aids and Accessories section of this
manual.
y The proper throat plate must be in place at all times.
y If your saw makes an unfamiliar noise or if it
vibrates excessively, cease operating immediately
until the source has been located and the problem
corrected.
y Never perform freehand cutting, plunge cutting, re-
sawing or cove cutting.
AVOID KICKBACK
A kickback can occur when the workpiece pinches
the blade, or binds between the saw blade and the
rip fence or other xed object. This can cause the
workpiece to rise from the table and/or be thrown back
toward the operator. See instructions for reducing the
risk of kickback, in the Table Saw Safety Rules section
of this manual.
IF KICKBACK OCCURS, turn the saw “OFF” and verify
proper alignment of the blade, riving knife and miter
gauge or rip fence, and the proper functioning of the
riving knife, anti-kickback assembly and blade guard
assembly before resuming work.
LOCK
OUT
HOLE
ON
OFF
FIGURE 18
17
MAKING CUTS
y Never touch the free end of the workpiece or a free
piece that is cut off, while the power is on and/or
the saw blade is rotating. Blade contact or binding
may occur, resulting in a thrown workpiece
y When sawing a long workpiece or a panel, use a
work support, such as a sawhorse, rollers or outfeed
table at the same height as the table surface of the
saw.
y Never try to pull the workpiece back with the blade
turning. If you need to pull the workpiece back or lift
it off the table, turn the switch off, allow the blade to
stop, raise the anti-kickback teeth on each side of
the riving knife if necessary, and slide the workpiece
out.
y Before connecting the table saw to the power
source or operating the saw, always inspect the
blade guard assembly and riving knife for proper
alignment and clearance with saw blade. Check
alignment after each change of beveling angle.
y A rip fence should ALWAYS be used for ripping
operations to prevent loss of control and personal
injury. Always lock the fence to the rail. NEVER
perform a ripping operation freehand.
y When making bevel cuts, place the fence on the
right side of the blade so that the blade is tilted
away from the fence and hands. Keep hands
clear of the blade and use a push stick to feed the
workpiece unless the workpiece is large enough to
allow you to hold it more than 6 inches (152 mm)
from the blade.
y Before leaving the saw unattended, lock out power
switch, or take other appropriate measures to
prevent unauthorized use of the saw.
Failure to comply with the following warnings may result in serious personal injury.
CROSS CUT
BEVELED CROSS CUT BEVELED RIP CUT COMPOUND MITER CUT
MITERED CROSSCUTRIP CUT
CIRCUIT BREAKER SAFETY
AND INSTRUCTION
This saw is equipped with a 15 amp overload circuit
breaker (A) located above the saw main power ON/OFF
switch. During a power overload this breaker will trip
and disconnect all power to the motor. To reset, allow
unit to cool down for 3 to 5 minutes and then push the
breaker button back in. (g 19)
OPERATION
To prevent the tool from unexpectedly
starting, always turn the power switch
to the off position before resetting the circuit breaker
and/or reconnecting the power supply.
NOTE: Circuit breaker overload may be caused by
attempting to feed the workpiece too fast. Do not
overload the motor by forcing the workpiece into the
blade.
A
FIGURE 19
18
RIP CUTS
BEVEL RIPPING
Bevel ripping is the same as ripping except the bevel
angle (A) is set to an angle other than 0°. When making
a bevel rip cut, place the fence on the right side of the
blade so that the blade is tilted away from the fence and
hands.(Fig. 21).
MAKING CUTS
1. Remove miter gauge
2. Make sure bevel angle is set to 0°.
3. Set blade to correct height for workpiece.
4. Install rip fence and lock it down parallel with and at
desired distance from blade.
5. Keep ngers at least 6 inches from the blade at
all times. When the hand cannot be safely put
between the blade and the rip fence, select a larger
workpiece, or use a push stick and other cutting
aids, as needed, to control the workpiece.
6. Make sure the workpiece is clear of the blade (at
least 1 inch or 25mm away) before starting the saw
7. Turn saw on.
8. Hold the workpiece at on the table and against the
fence (A). The workpiece must have a straight edge
against the fence and must not be warped, twisted
or bowed. See proper hand position in (Fig. 20).
9. Let blade build up to full speed before moving
workpiece into the blade.
10. Both hands can be used while starting the cut as
long as hands remain 6 inches from the blade.
11. Keep the workpiece against the table and fence
and slowly feed the workpiece rearward all the way
through the saw blade. Do not overload the motor
by forcing the workpiece into the blade.
12. Use the push stick and any other cutting aids, as
needed, to hold the workpiece against the table and
fence, and push the workpiece past the blade. A
push stick is included with this saw, and instructions
are included to make additional push sticks and
other cutting aids.
13. Do not push or hold onto the free or cut-off side of
the workpiece.
14. Continue pushing the workpiece until it is clear of
the blade. Do not overload the motor by forcing the
workpiece into the blade.
15. When cut is complete, turn saw off. Wait for blade
to come to a complete stop before removing
workpiece from table.
A
A
FIGURE 20
FIGURE 21
19
Miter crosscutting is the same as crosscutting except
the miter angel (B) is set to an angle other than 90˚ (Fig.
24).
y Miter angles more than 45˚ may force the blade
guard assembly into the saw blade causing damage
to the blade guard assembly and personal injury.
Before starting the motor, test the operation
by feeding the workpiece into the blade guard
assembly. If the blade guard assembly contacts
the blade, place the workpiece under the blade
guard assembly but not touching the blade - before
starting the motor.
y Certain workpiece shapes, such as
molding may not lift the blade guard assembly
properly. With the power off, feed the workpiece
slowly into the blade guard area and until the
workpiece touches the blade. If the blade guard
assembly contacts the blade, place the workpiece
under the blade guard assembly - but not touching
the blade - before starting the motor.
A
MAKING CUTS
CROSSCUTTING
BEVEL CROSSCUTTING
MITER CROSSCUTTING
Bevel crosscutting is the same as crosscutting except
the bevel angle (A) is set to an angle other than 0°.
When making a bevel crosscut, place the miter gauge in
the right miter slot so that the blade is tilted away from
the gauge and hands (Fig. 23).
y NEVER use the fence as a guide or length stop
when crosscutting.
y The cut-off piece must never be conned in any
through-sawing (cutting completely through the
workpiece) operation—to prevent pinching blade
which may result in a thrown workpiece and
possibly injury.
y When using a block as a cut-off gauge, the block
must be at least
3
/
4
-inch (19mm) thick. It is very
important that the rear end of the block be secured
in a position where the workpiece is clear of the
block before it enters the blade to prevent binding
of the workpiece.
You can use the miter gauge in either table slot on non-
bevel cuts. To increase surface area of miter gauge face,
add an auxiliary face (See Cutting Aids section on of this
manual.)
TO MAKE A CROSSCUT, REFER TO FIGURE 22 AND
FOLLOW THIS PROCESS:
1. Remove rip fence.
2. Make sure bevel angle is set to 0°.
3. Set blade to correct height for workpiece.
4. Place miter gauge in either miter slot.
5. Set miter gauge to 90° and tighten miter gauge lock
knob
6. Hands must remain at least 6 inches from blade
throughout entire cut. If workpiece is too small to
keep hands at least 6 inches away from the blade,
select a larger workpiece, or attach an auxiliary face
to the miter gauge and attach workpiece to auxiliary
face, For instructions about making auxiliary faces,
see Cutting Aids section of this manual.
7. Make sure the workpiece is clear of the blade - at
least 1 inch or 25mm away - before starting the saw.
8. Turn saw on.
9. Let blade build up to full speed before moving
workpiece into the blade.
10. Hand closest to blade should be placed on miter
gauge lock knob and hand farthest from blade
should hold workpiece rmly against the miter
gauge face. Do not push or hold onto the free or
cut-off side of the workpiece.
11. Slowly feed the workpiece rearward all the way
through the saw blade. Do not overload the motor
by forcing the workpiece into the blade.
12. When cut is complete, turn saw off. Wait for blade
to come to a complete stop before removing cut off
piece from table.
FIGURE 22
FIGURE 23
20
9
5
MAKING CUTS
COMPOUND MITER CUTS
LARGE PANEL CUTS
This is a combination of bevel crosscutting and mitering.
Refer to (Fig. 24) and follow the instructions for both
bevel crosscutting and mitering. Remember to use the
right miter slot on the right side of the blade for all bevel
cuts.
Place workpiece supports at the same height as the
saw table behind saw to support the cut workpiece, and
alongside (s) of saw, as needed. Depending on shape of
panel, use rip fence or miter gauge to control workpiece.
If a workpiece is too large to use either a rip fence or a
miter gauge, it is too large for this saw.
NON-THROUGH CUTS
MAKING A NON-THROUGH CUT
The use of a non-through cut is essential to cutting
grooves, and rabbets. Non-through cuts can be made
using a standard blade having a diameter of 10 inches.
Non-through cuts are the only type of cuts that should
be made without the blade guard assembly installed.
Make sure the blade guard assembly is reinstalled upon
completion of this type of cut.
y When making non-through cuts, follow all applicable
warnings and instructions listed below in addition to
those listed above for the relevant through cut.
y When making a non-through cut, blade is covered
by workpiece during most of cut. Be alert to
exposed blade at start and nish of every cut.
y Never feed wood with hands when making any non-
through cuts such as rabbets or grooves. Always
use miter gauge, push blocks or push sticks, and
featherboards where appropriate.
y In addition to this section, read the appropriate
section which describes the type of through or cut.
For example, if your non-through cut is a straight
cross cut, read and understand the section on
straight cross cuts before proceeding.
y Once all non-through cuts are completed, unplug
saw and return riving knife to through cut position.
Install anti-kickback pawls and blade guard.
y Carefully follow the instructions accompanying any
specialized blades for proper installation, set up and
operation.
1. Unplug saw.
2. Unlock bevel lock.
3. Adjust bevel angle to 0°.
4. Lock bevel lock.
5. Remove blade guard and anti-kickback pawls.
6. Place riving knife in “lowered” position. (See RIVING
KNIFE ADJUSTMENT Section)
7. Set blade to correct depth for workpiece.
8. Depending on shape and size of wood, use either
rip fence or miter gauge.
9. Plug saw into power source and turn saw on.
10. Let blade build up to full speed before moving
workpiece into blade.
11. Always use push blocks, push sticks, and/or
featherboards when making non-through cuts to
reduce the risk of serious injury.
12. When cut is made, turn saw off. Wait for blade
to come to a complete stop before removing
workpiece.
B
FIGURE 24
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Delta S36-290 Le manuel du propriétaire

Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues