EarthWise SN71018 Le manuel du propriétaire

Model SN71018

OPERATOR’S MANUAL

18” Snow Thrower

This product is covered by U. S. patents and other international patents

Thank you for your purchase.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY, PARTS, SERVICE QUESTIONS?

CALL 1-800-313-5111 BETWEEN 7:30AM-4:30PM EST FOR ASSISTANCE.

SAVE THIS MANUAL FOR FUTURE REFERENCE

This product has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual

before using this product.

PRODUCT SPECIFICATIONS

Model: SN71018

Power supply voltage: 120V-60HZ Clearing width: 18 inches (460 mm)

Idle speed: 2000 RPM Max clearing depth: 12 inches (305 mm)

Power consumption: 13.5 Amp Clearing capacity: 700 pounds/minute

Weight: 31 pounds Throwing distance: Up to 30 feet

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 - 5

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 9

2

Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 14

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

TABLE OF CONTENTS

PARTS LIST

Pos. Description

1 Switch box

2 Bail wire

3 Upper handle

4 Handle connector

5 Lower handle

6 Wheel assy.

7 Side cover

8 Chute crank

Pos. Description

9 Auxiliary handle

10 Knob

11 Chute deflector

12 Discharge chute

13 Auger

14 Scraper blade

15 Crank knob

3

2

1

4

5

7

9

12

8

13

14

6

11

10

15

Precautions that involve your safety.

CAUTION! Read the instruction manual and follow the warning and safety instructions!

CAUTION! Remove plug from outlet immediately if the cable is damaged or cut.

SWITCH OFF! the machine, wait until it comes to a complete standstill and remove plug from outlet prior to

maintenance, cleaning or repair work!

CAUTION! Always wear eye and ear protection.

Wear safe, sturdy, nonskid footwear!

DANGER! objects may be thrown out at high speed when motor is running. Do not walk in front of running

machine.

Keep bystanders at a safe distance.

Keep the electrical cord free of the auger. The auger may damage the cord and cause contact with live

parts.

DANGER! Rotating blades. Keep hands and feet at a safe distance.

Do not place hand under auger.

Do not place hand in front of chute deflector.

Do not expose to rain or use in damp locations.

DANGER! Risk of electric shock.

Do not use in rain or electrical storms.

Waste electrical products should not be disposed of with household waste. Please recycle

where facilities exist. Check with your Local Authority or retailer for recycling advice.

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

3

TO REDUCE RISK OF INJURY: Before any use

be sure everyone using this product reads and

understands all safety instructions and other

information contained in this manual.

CAUTION: Wear appropriate personal hearing

protection during use. Under some conditions

and duration of use, noise from this product may

contribute to hearing loss.

Save these instructions and review frequently prior

to use and in instructing others.

WARNING: When using electric appliances, basic

safety precautions should always be followed to

reduce risk of fire, electric shock, and personal

injury, including the following:

READ ALL INSTRUCTIONS

CHECK FOR DAMAGED PARTS - Before further

use of the product, any part that is damaged should

be carefully checked to determine that it will operate

properly and perform its intended function. Check

for alignment of moving parts, binding of moving

parts, breakage of parts, mounting and any other

condition that may affect its operation. Any part that

is damaged should be properly repaired or replaced.

For assistance call our customer service help line at

1-800-313-5111.

AVOID DANGEROUS ENVIRONMENTS - Do

not operate in gaseous or explosive atmospheres.

Motors in these products normally spark, and the

sparks might ignite fumes.

KEEP CHILDREN AWAY - All visitors, children and

pets should stay at a safe distance from the work

area.

DRESS PROPERLY- Don’t wear loose clothing or

jewelry and wear protective hair covering to contain

long hair. They can be caught in moving parts.

Wear safe, sturdy, nonskid footwear. Maintain good

footing at all times, especially on slopes.

USE SAFETY GLASSES - Wear safety glasses

with side shields or goggles that are marked to

comply with ANSI Z87.1 standard when operating

this product.

DOUBLE INSULATION – The snow thrower has

double insulation. This means that all external met-

al parts are insulated from the electrical supply.

This is achieved by introducing an insulation layer

between electrical and mechanical parts. The

double insulation guarantees you the greatest

possible safety.

WARNING: Use outdoor extension cords marked

SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A,

or SJTOWA. These cords are rated for outdoor use

and reduce the risk of electric shock.

POLARIZED PLUGS-To reduce the risk of electric

shock, this product has a polarized plug. Polarized

connections will fit together only one way. Make

sure that the receptacle end of the extension cord

has large and small blade slot widths. If the plug

does not fit fully into the extension cord, reverse

the plug. If it still does not fit, obtain a suitable

extension cord. If the extension cord does not fit

fully into the outlet, contact a qualified electrician to

install the proper outlet. Do not change the plug on

the tool or the extension cord in any way.

EXTENSION CORD. Make sure your extension

cord is in good condition. When using an extension

cord be sure it is heavy enough to carry the current

your product will draw. An undersized extension

cord will cause a drop in line voltage resulting in

loss of power and overheating. The following table

shows the correct size to use. Do not use an

extension cord over 150 feet.

It is possible to tie two extension

cords together in a knot to prevent

them from becoming disconnected

during use. Make the knot as

shown, then connect the plug end

of the power cord into the recepta-

cle end of the extension cord.

WARNING: Keep all connections dry and off the

ground. Do not touch plug with wet hands.

Be aware of the extension cord while operating the

snow thrower. Be careful not to trip on the cord.

Always keep the cord away from the auger.

IMPORTANT SAFETY WARNINGS

GENERAL SAFETY

4

Extension Cord Length

Minimum Wire Gauge (A.W.G.)

100 feet (30 m)

16

150 feet (46 m)

14

Operation of the snow thrower in the hand-held

position is unsafe except in accordance with the

special instructions for such use provided in the

operator’s manual.

CAUTION: Never throw snow towards people, pets

or cars and never allow anyone in front of the snow

thrower while in operation.

Objects that might clog the snow thrower or cause

other damage can be hidden in the snow. Clear

the area of doormats, sleds, boards, wires and

other debris prior to use.

If the auger strikes a foreign object, stop the snow

thrower and examine it for signs of damage. Make

any necessary repairs before restarting and

continuing to work.

STAY ALERT - Watch what you are doing. Use

common sense. Do not operate the snow thrower

when you are tired or under the influence of drugs,

alcohol or medications.

If the snow thrower starts to vibrate abnormally,

turn it off immediately and check for the cause.

Vibration is generally a warning of trouble.

Always turn off the snow thrower, wait until the

auger comes to a complete stop and disconnect

from the power supply before carrying out

maintenance or repairs.

Never operate the snow thrower without proper

guards and other safety protective devices in place

and working.

When servicing use only identical replacement

parts.

CAUTION: Auger does not stop immediately after

the snow thrower is turned off.

CAUTION: Risk of injury. This snow thrower is

capable of causing serious injury. Do not put

hands, feet or any body part or clothing near the

rotating auger.

WARNING: California Proposition 65:

This product contains chemicals known to the State

of California to cause cancer, birth defects or other

reproductive harm.

GROUND FAULT CIRCUIT INTERRUPTER (GFCI)

protection should be provided on the circuit or outlet

to be used for the snow thrower. Receptacles are

available having built-in GFCI protection and may

be used.

WARNING: Never put your hands near the auger to

remove snow, sticks or other debris. Blocked auger

can “spring back” when cleared and may cause

personal injury even when the snow thrower is

stopped. Always use a wooden stick such as a

broom handle to clear blockages.

DISCONNECT UNIT from the power supply when

not in use or when servicing or cleaning. Do not

leave unattended.

DON’T ABUSE CORD - Never carry this product

by the cord or yank the cord to disconnect from the

receptacle. Keep cord from heat, oil, and sharp

edges.

USE RIGHT APPLIANCE - Do not use this product

for any job except that for which it is intended.

DO NOT OVERLOAD the snow thrower by using at

too fast a rate to clear the snow. The snow thrower

will perform better and safer at the rate for which it

was designed.

DON’T OVERREACH - Guide the snow thrower at a

walking pace only. Keep proper footing and balance

at all times.

LIGHTING - Only operate your snow thrower in

daylight or good artificial light.

STORE IDLE UNIT INDOORS-When not in use, the

snow thrower should be stored indoors in a dry area

out of reach of children.

MAINTAIN UNIT WITH CARE-Keep clean for best

performance and to reduce the risk of injury. Inspect

extension cord periodically and replace if damaged.

Keep handles dry, clean and free from oil.

Do not operate the snow thrower on a slope that is

too steep for safe operation. When on slopes, slow

down and make sure you have good footing.

Before starting the snow thrower make sure the

auger is not touching any object and is free to move.

Do not attempt to clear snow from a gravel or

crushed rock surface. This product is only intended

for use on hard, flat surfaces free of sand, stone and

debris, wires or any other objects.

GENERAL SAFETY

5

ASSEMBLY

6

UNPACKING

This product requires assembly.

Carefully remove everything from the box. Make sure that

all items listed in the packing list are included.

Inspect all items carefully to make sure no breakage or

damage occurred during shipping.

Do not discard the packing material until you have

carefully inspected and satisfactorily operated the snow

thrower.

PACKING LIST

- Snow Thrower

- Handle Assembly

- Chute Crank

- Chute Deflector

- Operator’s Manual

ASSEMBLY

1. Remove the wingnuts and U-bolts from the handle

brackets. (Fig. 1 & Fig. 2)

Fig. 3

Fig. 1

Fig. 4

2. Align the holes in the lower handle section with those

in the handle brackets. (Fig. 3)

3. Secure the handle to the handle brackets with the

U-bolts and wingnuts. Make sure the wingnuts are

tightened. (Fig. 4 & Fig. 5)

Fig. 2

Fig. 5

5. Remove the spring pin from the crank rod. (Fig. 8)

6. Install the crank rod through the center plate and

insert it into the opening at the back of the housing

with holes aligned. (Fig. 9 & Fig. 10)

ASSEMBLY

7

4. Open the tabs on the handle connectors and adjust

the top handle to the desired position. Lock in

position by closing the tabs. (Fig. 6 & Fig. 7)

Fig. 6

Fig. 8

Fig. 10

Fig. 9

Fig. 7

9. Position the chute deflector over the discharge chute

and align the holes placing the washer between the

deflector and the chute. (Fig. 14 & Fig. 15)

ASSEMBLY

8

7. Secure the crank rod in place with the spring pin.

(Fig. 11 & Fig. 12)

8. Remove the wingnuts, washers and bolts from the

discharge chute. (Fig. 13)

Fig. 11

Fig. 12

Fig. 13

Fig. 14

Fig. 15

11. Turn the crank knob clockwise to secure the snow

deflector chute in position. (Fig. 18)

ASSEMBLY

9

10. Secure with the bolts and wingnuts. Make sure the

wingnuts are tightened. (Fig. 16 & Fig. 17)

Fig. 16

Fig. 17

Fig. 18

For the most efficient snow removal throw the snow

downwind and slightly overlap each swath.

Push the snow thrower forward at a comfortable rate of

speed, yet slow enough to clear the path completely. The

width and depth of the snow determines your forward

speed.

Start your clearing path near the electrical outlet and

work outward, throwing snow in a back and forth motion.

When turning at the end of a swath, step over the cord

and turn the snow thrower. Use the wheel on one side as

the pivot point. Slightly tilt the snow thrower on this pivot

point while turning.

The snow thrower can remove up to 12 inches deep in

one pass. To shave down larger banks of snow, lift the

snow thrower by the primary and auxiliary handles and

place the snow thrower on the bank. Let the weight of

the snow thrower shave down the bank by rocking it in a

back-and-forth motion.

When clearing steps, hold the snow thrower by the

primary and auxiliary handles and use a swinging or

sweeping motion.

Clear snow often, before it gets too deep. It is best to

remove the snow as soon as possible after it falls.

Some parts of the snow thrower may freeze under

extreme temperature conditions. If parts freeze while the

snow thrower is in use, stop the snow thrower, unplug the

extension cord and inspect for frozen parts. Free all parts

of ice before restarting or operating the snow thrower. Do

not attempt to operate the snow thrower with frozen parts

or try to force controls that are frozen.

After clearing the snow, continue to run the snow thrower

for a few minutes to prevent ice from freezing on moving

parts. Then switch off the motor, wait for all moving parts

to stop, and wipe the ice and snow from the snow thrower

with a clean rag.

WARNING: To avoid serious personal injury, do not

use hands or feet to unclog the chute.

Before unclogging the chute, shut off the snow thrower

and disconnect from the power supply. Wait for the auger

to stop turning. Clean out the chute with a wooden stick

such as a broom handle.

If the snow thrower should start to vibrate abnormally,

immediately stop the motor and check for the cause.

Vibration is generally a warning of trouble.

Look behind and use care when backing up with the

snow thrower.

OPERATING

10

If working on pebbles, gravel or unpaved surfaces - To

avoid throwing loose surface material along with the

snow, push down on the handle to raise the scraper at

the base of the unit above the pebbles or gravel. The

manufacturer is not liable for any damage or injury

resulting from misuse.

Turning On and Off

WARNING: The auger starts rotating immediately

after the snow thrower is switched on. Keep hands

and feet away from the auger.

To switch ON, make sure the auger is not touching any

surface and press the Safety Lock Off Button while

squeezing the Bale Wire (2).

Once the snow thrower is started you can release the

Safety Lock Off Button.

To switch Off simply release the Bale Wire.

Removing snow

Before starting work, thoroughly inspect the area where

the equipment is to be used and remove all doormats

sleds, boards, wires and any other foreign objects.

Check the condition of the snow thrower before operating

it to ensure that the auger turns freely.

Check the auger for wear and tear at regular intervals.

Make sure all fasteners on the snow thrower (screws,

nuts, etc.) are fully tightened.

Position the discharge chute so that snow will discharge

in a safe direction. Do not direct the discharge towards

people or areas where property can be damaged. Keep

children, pets and others away for the work area. Do not

walk in front of the snow thrower when it is running.

Direct the discharge to the right or left by turning the

discharge chute with the chute crank. The chute can be

adjusted up to 180 degrees. First loosen the crank knob

by turning it counter-clockwise. Turn the crank clockwise

to direct the discharge to the left; counterclockwise to

direct the discharge to the right. Tighten the crank knob

by turning clockwise to secure the discharge chute in the

desired direction.

The chute deflector on the top of the discharge chute

controls the height of the discharge. Loosen both of the

T-knobs to raise or lower the deflector to the desired

height and tighten the T-knobs to secure the deflector.

NOTE: Do not over-tighten the T-knobs.

OPERATING

For large areas a definite pattern of operation is required

to thoroughly clean an area of snow. These patterns

will avoid throwing snow in unwanted places as well as

eliminating a second removal of snow.

Pattern A: Throw the snow to the right or left side where

it is possible. For areas such as a long driveway it is

advantageous to start in the middle. Plow from one end

to the other, throwing snow to both sides.

Pattern B: If the snow can only be thrown to one side of

the area to be cleared, start on the opposite side.

Overload Protection

The reset button will be tripped and will automatically

shut down the snow thrower if the circuit is overloaded.

To restart, press the reset button and follow the steps

provided for turning on the snow thrower.

11

MAINTENANCE

Before carrying out maintenance operations, disconnect power supply.

Replacing the scraper

The scraper is located at the base of the snow thrower

beneath the rotor housing.

Remove the screws that secure the scraper to the snow

thrower.

Install the new scraper and fasten it securely with the

screws.

Replacing the auger belt

Under normal operating conditions it should not be

necessary to replace the auger belt. However, should

the auger jam or malfunction the belt could be damaged.

To replace the belt follow these instructions.

Belt drive system structure

12

Regular cleaning and maintenance of your snow thrower

will ensure efficiency and prolong the life of the product.

Check all fasteners at frequent intervals for proper

tightness to be sure the snow thrower is in safe working

condition.

After each use, let the motor run for a few minutes so that

moving parts do not freeze. Then shut off the motor, wait

for all moving parts to stop, and wipe the ice and snow

from the snow thrower. Rotate the chute crank several

times to remove snow.

Only use a cloth soaked with hot water and a soft brush

to clean the snow thrower. Never wet or spray water on

the machine!

Do not use detergents or solvents as these could cause

irreparable damage to the snow thrower. Chemicals can

destroy the plastic parts.

To protect the snow thrower from corrosion when storing

for long periods, lightly oil the metal parts.

Store the appliance in a dry area out of reach of children.

For the user’s safety, worn or damaged parts must be

replaced. Replace with original replacement parts only.

Parts from another snow thrower may not fit properly

causing an unsafe situation.

Lubricating the snow thrower

You do not need to lubricate the snow thrower. All of the

bearings are sealed and were lubricated at the factory for

the life of the snow thrower.

Replacing the rubber plates

Detach the worn rubber plate by removing the two sets of

nuts, bolts, and washers used to secure it.

Install the new rubber plate.

Insert the bolt with the small flat washer into the

corresponding holes on each end of the rubber plate.

Use a large flat washer and locknut to secure the bolt

on each end.

Install the other rubber plate in the same manner.

Main Drive Belt

Auger Pulley

Auger Belt

Drive Pulley

MAINTENANCE

1. Open the left side plate by removing three (3)

screws. (Fig. 19)

2. Use your right hand to turn the rib side of the belt

up and pull upwards while turning the auger pulley

counterclockwise with your left hand. The belt can be

easily removed from the pulley. (Fig. 20 & Fig. 21)

Fig. 19

13

3. Put the belt on the drive pulley first and then place

the belt at the lower end of the auger pulley. (Fig. 22)

4. Use right hand to press the belt with ribbed side

down. (Fig. 23)

5. While holding the belt down with your right hand use

your left hand to turn the auger forward so that the

auger pulley rotates in a clockwise direction. (Fig. 24)

Fig. 21

Screws

Fig. 20

Fig. 22

Fig. 23

Fig. 24

MAINTENANCE

6. Keep pressure on the belt with your right hand (rib

side down and flat side up) while rotating the auger.

The belt will be gradually pushed down onto the

pulley. When the belt is seated on the pulley, adjust

it so that the ribs of the belt match the grooves on

the pulley. (Fig. 25, Fig. 26, Fig. 27 & Fig. 28)

Fig. 25

14

7. After belt is installed, replace the side plate and

secure it with the three screws. (Fig. 29)

Fig. 27

Fig. 26

Fig. 29

Screws

Fig. 28

Call us first with questions about operating or maintaining this product at 1.800.313.5111

between 7:30 a.m. – 4:30 p.m. Eastern Standard Time, or send emails to [email protected].

CALL US FIRST !!

SERVICE

Now that you have purchased your snow thrower, should you need repair parts or service, simply contact us at

1-800-313-5111. Be sure to provide all pertinent facts when you call.

REPAIR PARTS

Please record your serial number in the space provided below.

• NAME OF ITEM Snow Thrower

• MODEL NUMBER SN71018

• SERIAL NUMBER

Run the snow thrower for a few minutes to melt away any

snow on the snow thrower.

Disconnect the extension cord from the snow thrower.

Examine the extension cord thoroughly for signs of wear

or damage. Replace it if it is worn or damaged.

Examine the snow thrower thoroughly for worn, loose, or

damaged parts. Check connections and screws and

tighten if necessary. To repair or replace parts, contact

our customer service help line at 1-800-313-5111.

Store the snow thrower, along with.the disconnected

extension cord, in a clean, dry place out of reach of

children. Cover loosely with a tarp for added protection.

15

STORAGE

TROUBLESHOOTING

Problem Possible causes Remedy

Motor does not start Unit not plugged in.

No electricity.

Defective cable.

Plug in the unit.

Check power supply.

Check cable. Repair or replace if required.

Poor results Drive belt worn or damaged.

Auger worn or damaged.

Discharge chute blocked.

Replace the drive belt.

Replace the auger. Ensure the screws and nuts are

properly tightened.

Switch off the snow thrower and clean the discharge

chute.

Abnormal vibrations Drive belt worn or damaged.

Auger worn or damaged.

Scraper blade worn or damaged.

Replace the drive belt.

Replace the auger. Ensure the screws and nuts are

properly tightened.

Replace the scraper blade. Ensure the screws are

properly tightened.

Motor shuts off during

operation

Current too high Push reset button. Restart the snow thrower.

The Great States Corporation

American Lawn Mower Company

830 Webster Street

Shelbyville, IN 46176

www.americanlawnmower.com

WARRANTY

This product is manufactured for The Great States Corporation/American Lawn Mower Company. The

Great States Corporation/American Lawn Mower Company, Shelbyville, Indiana, has been making

lawn mowers for over 100 years and it warrants to the original owner that each new product and

service part is free from defects in material and workmanship and agrees to repair or replace under

this warranty any defective product or part from the original date of purchase for two (2) years except

for the conditions and circumstances listed below. Proof of purchase (original dated sales receipt)

must accompany all warranty claims.

THIS WARRANTY IS NOT TRANSFERABLE AND DOES NOT COVER:

Products sold damaged or incomplete, sold

“as is”, sold reconditioned, or used as rental

equipment.

Delivery, installation, or normal adjustments

explained in the operator’s manual.

Damage or liability caused by shipping,

improper handling, improper installation,

incorrect voltage or improper wiring,

improper maintenance, improper

modification, or the use of accessories and/

or attachments not specifically

recommended.

Repairs necessary because of operator

abuse or negligence, or the failure to install,

operate, maintain, or store the product

according to the instructions in the

operator’s manual.

Damage caused by cold, heat, rain,

excessive humidity, corrosive environments

and materials, or other contaminants.

Expendable items that become worn

during normal use, including but not limited

to, auger and scraper blade.

Cosmetic defects that do not interfere with

product functionality.

Freight costs from customer to vendor.

Repair and transportation costs of products

or parts determined not to be defective.

ANY INCIDENTAL, INDIRECT, OR

CONSEQUENTIAL LOSS, DAMAGE, OR

EXPENSE THAT MAY RESULT FROM

ANY DEFECT, FAILURE, OR

MALFUNCTION OF THE PRODUCT.

Some states do not allow the exclusion or

limitation on how long an implied warranty

lasts, so the above limitations may not

apply to you.

ANY NON-RESIDENTIAL USE OR

COMMERCIAL USE VOIDS ALL

WARRANTIES.

The Great States Corporation

American Lawn Mower Company

830 Webster Street

Shelbyville, IN 46176

Phone 1-800-313-5111

www.americanlawnmower.com

In a continued commitment to improve quality, the Manufacturer reserves the right to

make component changes or design changes when necessary.

OPERATOR’S MANUAL

18” Snow Thrower

This product is covered by U. S. patents and other international patents

Rev. 02/20/2013

Modelo SN71018

MANUAL DEL OPERARIO

Sopladora de nieve de 460 mm (18 pulg.)

Este producto está amparado por patentes de EE. UU. y otras patentes internacionales

Muchas gracias por su compra.

NO DEVUELVA ESTE PRODUCTO A LA TIENDA. ¿TIENE PREGUNTAS SOBRE EL FUNCIONAMIENTO, EL MONTAJE,

LAS PIEZAS Y EL MANTENIMIENTO? LLAME AL 1-800-313-5111 ENTRE LAS 7:30 Y LAS 16:30 HS., HORA DEL ESTE

DE LOS ESTADOS UNIDOS.

GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS

Este producto fue diseñado y fabricado de acuerdo con nuestros altos estándares de confiabilidad, facilidad de operación y seguridad

para el operario. Si se trata con cuidado, esta herramienta le otorgará años de óptimo rendimiento y resistencia.

ADVERTENCIA: Para reducir el riesgo de sufrir alguna lesión, el usuario debe leer y comprender

el manual del operario antes de usar este producto.

ESPECIFICACIONES DEL PRODUCTO

Modelo: SN71018

Voltaje del suministro eléctrico: 120 V - 60 HZ Ancho de barrido: 460 mm (18 pulg.)

Velocidad de ralentí: 2000 RPM Profundidad máx. de barrido: 305 mm (12 pulg.)

Consumo: 13,5 amperios Capacidad de barrido: 318 kg (700 libras)/minuto

Peso: 14 kg (31 libras) Distancia de lanzamiento: Hasta 914 cm (30 pies)

Especificaciones del producto . . . . . . . . . . . . . . . . . . . . . . 2

Lista de piezas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Símbolos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Advertencias de seguridad. . . . . . . . . . . . . . . . . . . . . . .4 - 5

Montaje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 9

2

Funcionamiento. . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 11

Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 14

Almacenamiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Solución de problemas . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

ÍNDICE

LISTA DE PIEZAS

Ref. Descripción

1 Caja del interruptor

2

Empuñadura de

arranque

3 Mango superior

4 Conector de mango

5 Mango inferior

6 Conjunto de la rueda

7 Tapa lateral

8 Manivela de descarga

Ref. Descripción

9 Mango auxiliar

10 Perilla

11 Deflector de descarga

12 Canal de descarga

13 Barrena

14 Cuchilla raspadora

15 Perilla de la manivela

3

2

1

4

5

7

9

12

8

13

14

6

11

10

15

Los productos eléctricos no se deben desechar junto con los residuos domésticos. Recicle

donde haya centros para tal fin. Consulte a la autoridad local o al distribuidor minorista para

obtener asesoramiento sobre reciclado.

SÍMBOLOS

Algunos de los siguientes símbolos pueden aparecer en este producto. Tenga a bien estudiarlos y aprender su significado.

La adecuada interpretación de estos símbolos le permitirá operar el producto mejor y de manera más segura.

3

Precauciones para su seguridad.

PRECAUCIÓN: Lea el manual de instrucciones y atienda las instrucciones se seguridad y advertencia.

PRECAUCIÓN: Retire el enchufe del tomacorriente de inmediato si el cable está dañado o cortado.

APAGUE la máquina, espere hasta que se detenga por completo y retire el enchufe del tomacorriente

antes de realizar alguna tarea de mantenimiento, limpieza o reparación.

PRECAUCIÓN: Use siempre protecciones para sus ojos y oídos.

Use calzado seguro, resistente y antideslizante.

¡PELIGRO! Pueden ser lanzados objetos a gran velocidad cuando el motor está en funcionamiento. No

pase delante de la máquina cuando está funcionando.

Mantenga a las personas que se encuentran en el lugar a una distancia segura.

Mantenga el cable eléctrico lejos de la barrena. La barrena puede dañar el cable y producir un contacto con

piezas activas.

¡PELIGRO! Cuchillas giratorias. Mantenga manos y pies a una distancia segura.

No colocar la mano debajo de la barrena.

No colocar la mano enfrente del deflector de descarga.

No exponga la unidad a la lluvia ni la use en lugares húmedos.

¡PELIGRO! Riesgos de descargas eléctricas.

No usar en la lluvia. No usar durante tormentas eléctricas.

PARA REDUCIR EL RIESGO DE LESIONES: Antes

de utilizar este producto, cerciórese de que todos

los usuarios lean y comprendan las instrucciones

de seguridad y la demás información incluida

en este manual.

PRECAUCIÓN: Use protección auditiva apropiada

mientras trabaja. En ciertas condiciones y con cierta dura-

ción de uso, el ruido generado por este producto puede

contribuir a la pérdida de la audición.

Guarde estas instrucciones y revíselas con frecuencia

antes de usar la herramienta y para impartirlas a otros.

ADVERTENCIA: Al utilizar aparatos eléctricos,

se recomienda respetar siempre las precauciones

de seguridad básicas que se detallan a continuación,

a fin de reducir riesgos de incendios, descargas

eléctricas y lesiones personales.

LEA TODAS LAS INSTRUCCIONES

CONTROLE SI HAY PIEZAS DAÑADAS. Antes de seguir

usando el producto, se deberán revisar las piezas daña-

das en forma exhaustiva para determinar

si la herramienta funcionará correctamente y realizará

el trabajo previsto. Compruebe la alineación y las uniones

de las piezas móviles, el montaje, averías

de componentes y otros factores que puedan afectar

el funcionamiento. Se debe reparar o reemplazar

cualquier pieza dañada en forma adecuada. Para recibir

asistencia, comuníquese con nuestra línea de ayuda

de atención al cliente al 1-800-313-5111.

EVITE AMBIENTES PELIGROSOS. No trabaje

en entornos donde existan gases o sustancias explosivas.

Por lo general, los motores de estos productos producen

chispas que podrían inflamar los gases.

MANTENGA ALEJADOS A LOS NIÑOS. Todos

los visitantes, niños y mascotas deben mantenerse

a una distancia segura de la zona de trabajo.

USE ROPA ADECUADA. No use prendas sueltas

ni artículos de joyería. Use protección para cubrir y sujetar

el cabello largo, ya que puede quedar atrapado

en las piezas móviles.

Use calzado seguro, resistente y antideslizante.

En todo momento mantenga una buena base

de apoyo, especialmente en pendientes.

USE GAFAS DE SEGURIDAD. Al trabajar con este

producto, use gafas de seguridad con protectores

laterales que cumplan con la norma ANSI Z87.1.

DOBLE AISLAMIENTO. La sopladora de nieve tiene

doble aislamiento. Es decir que todas las piezas metálicas

externas están aisladas del suministro eléctrico.

Esto se logra con la introducción de una capa de

aislamiento entre las piezas eléctricas y las mecánicas.

El doble aislamiento garantiza la mayor seguridad posible.

ADVERTENCIA: Use cables de extensión para exteriores

rotulados con las siguientes inscripciones: SW-A, SOW-A,

STW-A, STOW-A, SJW-A, SJTW-A, o SJTOWA. Estos

cables están especificados para usar al aire libre y reducir

el riesgo de descarga eléctrica.

ENCHUFES POLARIZADOS. Para reducir el riesgo

de descarga eléctrica, este producto tiene un enchufe

polarizado. Las conexiones polarizadas encajan

de una sola manera. Cerciórese de que el extremo

del receptáculo del cable de extensión tenga ranuras

de anchos diferentes para los contactos. Invierta

el enchufe si no encaja totalmente en el cable

de extensión. Si aún así no encaja, consiga un cable

de extensión adecuado. Si el cable de extensión no

se adapta bien al tomacorriente, llame a un electricista

competente para que instale un tomacorriente adecuado.

No modifique el enchufe de la herramienta ni el cable

de extensión de ningún modo.

CABLE DE EXTENSIÓN. Asegúrese de que el cable

de extensión esté en buenas condiciones. Además,

compruebe que tenga el grosor suficiente para

transportar la corriente que necesitará el producto.

Un cable de extensión muy pequeño provocará una

disminución en la tensión de la línea y, como resultado,

una pérdida de potencia y recalentamiento. La siguiente

tabla muestra el tamaño correcto que se debe usar. No

utilice un cable de extensión de más de 46 m (150 pies).

Es posible unir dos cables

de extensión con un nudo para evitar

que se desconecten durante el uso.

Realice el nudo como se muestra

en la imagen y luego conecte

el enchufe del cable de alimentación

en el receptáculo del cable

de extensión.

ADVERTENCIA: Mantenga todas las conexiones

secas y alejadas del suelo. No toque el enchufe

con las manos mojadas.

Tenga presente el cable de extensión mientras opera

la sopladora de nieve. Tenga cuidado de no tropezar con

el cable y manténgalo siempre alejado de la barrena.

ADVERTENCIAS DE SEGURIDAD IMPORTANTES

NORMAS GENERALES DE SEGURIDAD

4

Longitud del cable

de extensión

Calibre mínimo del cable (AWG)

30 m (100 pies)

16

46 m (150 pies)

14

La page charge ...

EarthWise SN71018 Le manuel du propriétaire

EarthWise SN71018 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents