Megger BMM500 Series Manuel utilisateur

This instrument is manufactured in the United Kingdom.

The company reserves the right to change the speciﬁcation or design without prior notice.

Part No 6172-697 - Edition 1 - Printed in England - 06FF

AVO INTERNATIONAL

Archcliffe Road PO Box 9007 4271 Bronze Way MEGGER SARL

Dover Valley Forge Dallas 29 Allée de Villemomble

Kent, CT17 9EN. PA 19484-9007 TX 75237-1017 93340 Le Raincy

England. U.S.A. U.S.A. Paris, France

Tel: +44 (0) 1304 502100 Tel: +1 (610) 676-8500 Tel: +1 (800) 723-2861 (U.S.A. only) Tel: +33 (1) 43.02.37.54

Fax: +44 (0) 1304 207342 Fax: +1 (610) 676-8610 Tel: +1 (214) 330-3203 (International) Fax: +33 (1) 43.02.16.24

MEGGER

®

User Guide

Guide d’Utilisateur

Benutzeranleitung

Guía del Usuario

INSULATION & CONTINUITY

TESTERS

MEGGER

®

BMM500 SERIES

Contents

Safety Warnings 2

Description 3

Operation 4

Live Circuit warning 4

Voltage testing 4

Auto-shut off 4

Backlight 4

Insulation tests 5

Locking Test Button (ltb) 5

Polarisation Index Testing 5

Automatic Discharge 6

Zeroing of Test Lead Resistance 7

Possible sources of error 7

Continuity Bleeper 8

Resistance Tests (kΩ)8

Diode Testing 8

Voltage Tests (V) 9

Battery Replacement 10

Fuse Checking and Replacement 10

Using the MEGGER SP1

Switched Probe 11

Speciﬁcation 12

Repair and Warranty 19

1

Symbols used on the instruments are:

Caution, risk of electric shock.

Caution, refer to User Guide.

Equipment protected throughout

by Double Insulation (Class II).

Equipment complies with

current EU Directives.

Equipment must not be

connected to voltage sources

>600V CAT II. Suitable for

electrical installations CAT III

300V to Earth

>600V

2

SAFETY WARNINGS

• Safety Warnings and Precautions must be read and understood before the instrument is used. They

must be observed during use.

• The circuit under test must be de-energised and isolated before connections are made except for

voltage measurement.

• Circuit connections must not be touched during a test.

• After insulation tests, capacitive circuits must be allowed to discharge before disconnecting the test

leads.

• The Live Circuit Warning and Automatic Discharge are additional safety features and should not be

regarded as a substitute for normal safe working practice.

• Replacement fuses must be of the correct type and rating. Failure to ﬁt the correctly rated fuse will result

in damage to the instrument in the event of an overload.

• Test leads, including crocodile clips, must be in good order, clean and have no broken or cracked

insulation.

• Ensure that hands remain behind guards of probes/clips when testing.

• U.K. Safety Authorities recommend the use of fused test leads when measuring voltage on high energy

systems.

NOTE

THE INSTRUMENTS MUST ONLY BE USED BY SUITABLY TRAINED AND COMPETENT PERSONS

Users of this equipment and/or their employers are reminded that Health and Safety Legislation require them to carry out valid risk assessments

of all electrical work so as to identify potential sources of electrical danger and risk of electrical injury such as from inadvertent short circuits.

Where the assessments show that the risk is signiﬁcant then the use of fused test leads constructed in accordance with the HSE guidance note

GS38 ‘Electrical Test Equipment for use by Electricians’ should be used.

Description

Congratulations on your purchase of a genuine

Megger insulation/continuity tester. Megger has

over 100 years experience in insulation testing

which is reﬂected in its product designs. Your

BMM500 has been carefully developed to

address the real needs and beneﬁts of the user.

The MEGGER BMM500 Series instruments

are battery powered Insulation and Continuity

testers, with a measurement capability from

0,01Ω Continuity to 10GΩ Insulation.

Offering multi-voltage facilities, the instruments

take full advantage of microprocessor

technology and feature a large liquid crystal

display combining digital and analogue

readings. The analogue display has the beneﬁt

of indicating trends and fluctuations in

readings, while the digital readout gives direct

accurate results. The display is also backlit

giving clear visibility even in low light

conditions.

The BMM500 Series instruments have the

unique capability of being able to measure

voltages down to a resolution of 0,1mV. This

gives the user the option to ﬁt a wide variety of

transducers to further enhance the capabilities

of the BMM Series instruments, eg temperature

or humidity measurement.

A customised connector on the top of the

instrument enables the optional MEGGER SP1

Switched Probe to be used for two handed

probe operation.

The 250V, 500V and 1000V ranges can be

used to test electrical installations in

compliance with BS7671 (16th Edition IEE

Wiring Regulations) IEC364 and HD384, since

each range has a 1mA minimum test current at

the minimum pass values of insulation

speciﬁed in these documents. Designed to

IEC1010-1 the BMM500 Series are protected

against connection to a 300V Category III

supply. The instruments have a basic accuracy

of ±2% at 20°C. The instruments are

waterproof and dustproof to IP54. This helps

maintain accuracy and ensures maximum

reliability in harsh environments.

3

Operation

Refer to Safety Warnings before using

the instrument

Testing is automatically inhibited if:

• An external voltage >55V is present when

switched to any insulation range position

• An external voltage >10V is present on all

other ranges (excluding OFF/V).

The external voltage is indicated on the display,

on insulation ranges an audible bleeper will

sound if a test is attempted.

Live Circuit Warning

When more than 25V is applied to the terminals

in the insulation ranges, the instrument defaults

to a voltmeter and gives an audible warning.

On all other switch positions except OFF/V

when approx 10V is applied the default

voltmeter will be activated. Testing will be

inhibited.

Voltage Testing on High Energy Systems

Use extreme care when using or measuring

voltages above 30V, particularly in high energy

systems. Fused test leads are available as

optional accessories for local situations where

increased protection is required.

Auto-shut Off

To conserve battery life, Auto-shut Off

(preceded by a series of bleeps) operates after

approx. 10 minutes of instrument inactivity on

insulation, 5 minutes on all other ranges. If the

instrument is switched on whilst holding the

key, the Auto shut-off time is extended to

60 minutes. To restore operation after Auto-

shut Off, select OFF followed by the required

switch position.

Note: It is recommended that the instrument is

switched to the OFF position when not

in use.

Backlight

The backlight is activated by pressing the

key. The backlight will remain illuminated

for approx. one minute before automatically

switching off to conserve battery life,

4

∼

Operation

alternatively the key can be re-pressed.

Insulation Tests (MΩ) (See ﬁg. 1)

The insulation tests apply a known voltage to

the circuit under test and measure the resulting

leakage current. The circuit under test must be

completely de-energised and isolated before

test connections are made.

Insulation tests are only initiated when the

TEST button is pressed.

1. Set the range switch to the test voltage

required.

2. Connect the test leads, ﬁrst to the

instrument, and then to the isolated item

under test.

3. Press the TEST button to activate the test

voltage. Take the reading.

4. Release the TEST button at the end of the

test.

5. Any capacitive circuits charged during a test

will automatically discharge. If signiﬁcant

voltage remains the voltage warning will

occur and the voltage present displayed.

6. Remove the test leads only when no

voltage is indicated.

Locking Test Button (ltb)

When it is desired to do a long insulation test,

the test can be ‘locked on’ by pressing the

key while the test button is held down.

The warning will appear on the display and

both buttons may be released whilst the test

continues. The next press of the test button will

terminate the test.

Note: There is a short delay on the ﬁrst operation

of ‘1000V’ range, each time the range is

selected. This is to prevent accidental

application of 1kV.

Polarisation Index Testing

Polarisation Index (PI) is the term applied to the

Dielectric Absorption Ratio when resistance

values are measured after 1 minute and again

after 10 minutes. Polarization Index is then the

resistance value after 10 minutes divided by the

resistance value after 1 minute. The test can be

run at any voltage. More detailed information

5

∼

Operation

on PI Testing and value assessment can be

found in AVO International publications listed in

the Accessories page.

Automatic Discharge

When the TEST button is released after an

insulation test (or re-pressed if ltb feature is

enabled), a 200kΩ load is automatically

switched across the terminals to discharge the

item under test. Any voltage present will be

indicated on the display so that the discharge

can be monitored.

Typical Terminal Voltage Characteristics

Continuity Testing (Ω) (See ﬁg.2)

The continuity tests are activated when the

probes make contact of less than a few kΩ. The

tests apply a constant current and measure the

resulting volt drop across the circuit under test.

The test operates without the need to press the

TEST button. When the test leads are removed

6

L1

L2

L3

N

Fig.1

1100

1000

900

800

700

600

500

400

300

200

100

0.01 0.1

1 10 100 1000

1000V

500V

250V

RESISTANCE (MΩ)

VOLT (d.c.)

Operation

the reading will hold for a few seconds and then

reset. This range is not suitable for diode

testing since the automatic contact detector will

not be activated when connected to a diode.

1. Set the selector switch to Ω.

2. Connect the test leads.

3. The test will activate automatically.

4. After the test probes are disconnected, the

reading will be held for a few seconds.

Zeroing of Test Lead Resistance

The resistance of the test leads can be nulled

on the continuity range (up to 9,99Ω). The null

information is retained in non-volatile memory

and so will be remembered when the

instrument is switched off.

1. Select the Continuity range.

2. Short the test leads across a known good

conductor using prods.

3. When the reading has stabilised, press the

TEST button. The zero offset symbol

will appear.

4. To release the zero offset press the TEST

button again.

Possible sources of error

Measurements and results can be effected by

the following:

• The impedance of operating circuits

connected in parallel

• Impedance such as inductors that vary during

the measurement

• A poor connection to the circuit under test.

7

L1

L2

L3

N

PE

Fig.2

Continuity Bleeper

The continuity bleeper sounds continuously

when a resistance below the threshold level is

detected. This can be selected from several

values between 2Ω and 3kΩ. To change the

level press the button. Short bleeps will

sound for values above the threshold but below

approx. 3kΩ

1. Set the selector switch to

2. Connect the test leads.

Display (5Ω level selected): Audible:

<5Ω continuous bleep

<3kΩ short bleep

>3kΩ no bleep

To turn off the audible tone and replace it with a

visual indication of continuity, press the TEST

button whilst switched to the range.

will be displayed momentarily and will

appear when resistances below the threshold

are measured.

Resistance Tests (kΩ)

This is a low voltage (5V) low current (25µA)

test for sensitive electronic equipment. It

operates in the same way as the continuity

ranges.

1. Set the selector switch to kΩ.

2. Connect the test leads.

3. The test will activate automatically.

The resistance range is protected by a high

impedance method and therefore if the

instrument is connected to a live circuit the fuse

will not blow as on the insulation, continuity and

buzzer ranges. The instrument will merely

indicate the applied over-voltage.

Diode Testing

This range can also be used for diode testing,

the positive terminal being the source of the

test current. A forward biased semi-conductor

junction will typically measure 15 to 30kΩ and

the diode symbol is shown on the display.

A reverse junction will measure much higher.

These features together with the small test

Operation

8

∼

Operation

9

∼

current and wide measurement range(0,01kΩ

to 10000kΩ) make the resistance range very

useful for general purpose testing.

Voltage Tests (V)

If >1V a.c. or d.c. is present at the terminals the

measured voltage is indicated on the display.

The voltage display will function within

speciﬁcation even if the fuse has blown.

If the voltmeter operation is in question, test the

voltmeter on a known source.

1. Set the selector switch to V.

2. Connect the test leads.

3. After a short settling time, the reading will

be displayed automatically.

Millivolt Tests (mV)

The measured a.c. or d.c. voltage is indicated

on the display.

1. Set the selector switch to mV.

2. Select either ac or dc mV using the

key.

3. Connect the test leads.

4. After a short settle time, the reading will

be displayed automatically.

Measuring Other Parameters

The BMM500 Series can be used to measure

numerous quantities from temperature to

current to windspeed through the use of mV

output probes. Any compatible probe with a

known output ratio can be used. eg: a

temperature probe with output ratio of 1mV/ºC

will cause the display to indicate directly

in ºC Certain probes require zeroing, eg

windspeed anemometer. The mV zero option

described below provides this facility

Zeroing of d.c. mV (no a.c. mV zero facility)

To zero the d.c. mV range, short the leads

together in the d.c. mV position, wait for the

reading to settle and then press the TEST

button. Up to 9,9mV can be zeroed on the d.c.

mV range. The symbol will appear to

indicate the zero has been adjusted.

Operation

1. Select the d.c. mV range.

2. Short the test leads together.

3. When the reading has stabilised, press the

TEST button. The zero offset symbol

will appear.

4. To release the zero offset press the TEST

button again.

Battery Replacement

When the low battery symbol appears, the

cells are nearly exhausted and should be

replaced as soon as possible. Use Alkaline

cells IEC LR6 (AA) or NiCd/NiMH

rechargeable. To install or replace the cells,

disconnect the test leads, switch the instrument

to OFF and loosen the captive screws on the

rear of the battery compartment. Remove the

cover and disconnect the battery holder from

the battery leads. Ensure that the replacement

cells are ﬁtted with the correct polarity in

accordance with the label in the battery holder.

Reconnect the battery holder to the battery

leads. Replace and re-secure the battery

compartment cover. Remove the cells if the

instrument is not going to be used for an

extended period of time.

The BMM500 Series incorporates an electronic

contact detector to minimise the chance of

blowing the fuse even if accidentally applied to

a live circuit whilst switched to the continuity

range. In the unlikely event of the fuse needing

replacement, a spare is located under the

battery cover.

Fuse Checking and Replacement

To check the instrument fuse, switch to an

insulation range and press the TEST button.

The symbol will appear if the fuse is

ruptured. To replace the fuse, disconnect the

test leads, switch the instrument OFF and

loosen the captive screws holding the battery

compartment cover in place. Remove the cover

and replace the fuse. Replace and re-secure

the battery compartment cover.

10

Operation

Using the MEGGER SP1 Switched Probe

Operation: The Megger SP1 is an accessory for

designated Megger installation test instruments.

When ﬁtted in the specially designed connector,

in place of the existing ‘Low’ lead, the SP1 acts

as a remote test button to operate the instrument

and as a ‘Low’ probe. This simpliﬁes instrument

control and two-handed probing. The SP1 is

suitable for use with MEGGER insulation test

instruments up to 1kV output test voltage.

Safety: Meets the safety requirements for double

insulation to IEC1010-2-031 (1995), EN61010-2-

031 (1995), IEC1010-1 (1995), EN61010-1

(1995) Category III*, 300V phase to earth. The

probe is ﬁtted with an internal, non-replaceable

fuse, to protect the user should the probe be

used accidentally in conjunction with a test lead

in the low terminal.

* Relates to transient overvoltage likely to be

found in ﬁxed installation wiring.

Do not use the probe if any part of it is

damaged.

11

Speciﬁcation

(All quoted accuracies are at +20°C.)

Insulation Ranges

Nominal Test Voltage (d.c.): 250V, 500V, 1000V

Test voltage accuracy: +15% maximum on open circuit

Short circuit current: < 2 mA

Test Current on load: 1mA at min. pass value of insulation speciﬁed in BS7671, HD384

and IEC364, 2mA max.

Accuracy Range Full Scale Accuracy

1000V 10GΩ ±2% ±2digits ±0,2% per GΩ

500V 5GΩ ±2% ±2 digits ±0,4% per GΩ

250V 2GΩ ±2% ±2 digits ±0,8% per GΩ

Note: Above speciﬁcations only apply when high quality silicone leads are being used.

Measuring Range: 0,01MΩ to 10GΩ

(0-100GΩ on analogue scale).

EN61557 Operating range: 0,10MΩ to 1GΩ

12

Speciﬁcation

Continuity

Measuring Range: 0,01Ω to 99,9Ω

(0-10Ω on analogue scale)

EN61557 Operating range: 0,10Ω to 99,9Ω

Accuracy: ±2% ±2 digits

Open circuit voltage: 5V ±1V

Test current: 210mA ±10mA (0-2Ω)

Zero offset at probe tips: 0,10Ω typical

Lead resistance zeroing: Up to 9,99Ω

Noise rejection: 1V rms 50/60Hz

Buzzer: Selectable: operates at less than 2Ω, 5Ω, 20Ω, 50Ω, 200Ω, 500Ω,

3kΩ approx.

Resistance

Measuring Range: 0,01kΩ to 9,99MΩ

(0 to 100MΩ on analogue scale)

Accuracy: ±3% ± 2digits

Open circuit voltage: 5V ±1V

Short circuit current: 25µA ±5µA

13

Speciﬁcation

Voltage

Measuring Range: ±1V to ±600V

(0 to 1000V on analogue scale)

Accuracy: 0-600V d.c. ±2% ±3 digit

0-600V a.c (50/60Hz) ±2% ±3 digits

0-600V 400Hz a.c. ±5% ±3 digits

Input resistance: approx 200kΩ.

Detector Threshold: 1V

Millivolts

Measuring Range: ±0,1mV to ±1999mV

(0 to 1000mV on analogue scale)

Accuracy:

0,1mV to 10mV d.c. or a.c. (50/60Hz) ±2% ±5 digits

10mV to 1999mV d.c. or a.c. (50/60Hz) ±2% ±3 digits

0,1mV to 10mV a.c. (16-460 Hz) ±5% ±7 digits

10mV to 1999mV a.c. (16-460 Hz) ±5% ±5 digits

d.c. milliVolts zeroing: Up to 9,9mV

Input resistance: >3MΩ

14

Speciﬁcation

Basic and service errors for Insulation and

Resistance ranges

The basic error is the maximum inaccuracy of

the instrument under ideal conditions, whereas

the service error is the maximum inaccuracy

taking into effect of battery voltage, temperature,

interference, and system voltage and frequency,

where applicable. After determining the service

error, we can then calculate the measurement

range. This is the range of measurement over

which the error in service is less than 30% of the

reading. Digital instruments are affected by the

number of digits error – for example a value

0,10Ω measured with the continuity range may

give a display in the range 0,07Ω to 0,13Ω which

is a maximum error of 30%. Therefore the

measurement range measuring low resistance is

0,10Ω to 99,9Ω. When checking that a

measurement does not exceed a limit, the

service error needs to be taken into account and

these tables enables this to be done quickly and

easily. These will guarantee that the value being

measured is greater than or less than the limit

value speciﬁed as appropriate.

Insulation Resistance – MΩ

Limit Min. Limit Min.

Indicated Indicated

Reading Reading

0,10 0,14 2,00 2,12

0,20 0,25 3,00 3,16

0,30 0,35 4,00 4,20

0,40 0,46 5,00 5,24

0,50 0,56

0,60 0,66

0,70 0,77

0,80 0,87

0,90 0,98

1,00 1,08

15

Speciﬁcation

Continuity Resistance – Ω

Limit Min. Limit Min.

Indicated Indicated

Reading Reading

0,10 0,06 2,00 1,88

0,20 0,15 3,00 2,84

0,30 0,25 4,00 3,80

0,40 0,34 5,00 4,76

0,50 0,44 10,00 9,56

0,60 0,54 20,00 18,8

0,70 0,63 30,00 28,4

0,80 0,73 40,00 38,0

0,90 0,82 50,00 47,6

1,00 0,92 100,00 92,0

SAFETY

The instruments meet the requirements for

double insulation to IEC 1010-1 (1995), EN

61010-1 (1995) to Category III*, 300V phase to

earth (ground) without the need for separately

fused test leads. If required, fused test leads are

available as an optional accessory.

* Relates to the transient overvoltages likely to

be met in ﬁxed wiring installations.

Complies with the following parts of EN61557,

Electrical safety in low voltage systems up to

1000V a.c. and 1500V d.c. – Equipment for

testing, measuring or monitoring of protective

measures:-

Part 1 – General requirements

Part 2 – Insulation resistance

Part 4 – Resistance of earth

connection and equi-

potential bonding

FUSE

500mA (F) 600V, 32x 6mm Ceramic HBC 10kA

minimum.

E.M.C.

The instruments meet EN 61326-1.

16

Speciﬁcation

POWER SUPPLY

Battery Type: 6x1,5V Alkaline

cells IEC LR6 type

or 1.2V NiCd or

NiMH

re-chargeable

cells.

Battery Life (typical): 2100 5-sec 1kV

insulation tests

3200 5-sec 500V

insulation tests

4000 5-sec 250V

insulation tests

2700 5-sec

continuity tests

4700 5-sec kΩ

tests

ENVIRONMENTAL CONDITIONS

Operating range: -10 to +50°C

Operating humidity: 90% RH at 40°C

max.

Storage temperature

range: -30 to +70°C

Calibration Temperature: +20ºC

Maximum altitude: 2000 m

Dust and water protection: IP54

Temperature coefﬁcient: <0,1% per °C

WEIGHT: 742g

DIMENSIONS: 110mm x 220mm

x 45mm

CLEANING: Wipe with a clean

cloth dampened

with soapy water

or Isopropyl

Alcohol(IPA)

17

La page charge ...

Megger BMM500 Series Manuel utilisateur

Megger BMM500 Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents