Tektronix P6245 Le manuel du propriétaire

Taper
Le manuel du propriétaire
Instruction Manual
P6245
1.5 GHz 10X Active Probe
070-8995-03
www.tektronix.com
Copyright © Tektronix, Inc. All rights reserved.
Tektronix products are covered by U.S. and foreign patents, issued and
pending. Information in this publication supercedes that in all previously
published material. Specifications and price change privileges reserved.
Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
WARRANTY
Tektronix warrants that the systems that it manufactures and sells, (excluding
customer-supplied equipment), will be free from defects in materials and workmanship for
a period of one (1) year. The warranty period shall begin on the date of installation or one
(1) month after the date of shipment, whichever is earlier. If any component of a system
supplied by Tektronix proves defective during the initial one-year period, Tektronix, at its
option, either will repair the defective component without charge for parts and labor, or
will provide a replacement in exchange for the defective component. If any component of
the system is a Tektronix product that is normally sold with a separate warranty, such
separate warranty will apply to the component whenever its terms are more favorable to
the Customer.
In order to obtain service under this warranty, Customer must notify Tektronix of the
defect before the expiration of the respective warranty period and make suitable
arrangements for the performance of service. Tektronix will provide such service at
Customers site without charge during the warranty period, if the service is performed
within the normal on-site service area. Tektronix will provide on-site service outside the
normal on-site service area only upon prior agreement and subject to payment of all travel
expenses by Customer. When or where on-site service is not available, Customer shall be
responsible for packaging and shipping the defective component to the service center
designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return
of the component to Customer if the shipment is to a location within the country in which
the Tektronix service center is located. Customer shall be responsible for paying all
shipping charges, duties, taxes, and any other charges for components returned to any other
locations.
This warranty shall not apply to any defect, failure, or damage caused by improper use or
improper or inadequate maintenance and care. Tektronix shall not be obligated to furnish
service under this warranty a) to repair damage resulting from attempts by personnel other
than Tektronix representatives to install, repair, or service the system; b) to repair damage
resulting from improper use or connection to incompatible equipment; c) to repair any
damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a
system that has been modified or integrated with other products when the effect of such
modification or integration increases the time or difficulty of servicing the system.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE
LISTED SYSTEMS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE
DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY
PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS
ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
P6245 Instruction Manual i
Table of Contents
Getting Started
Product Description 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Accessories 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customer Support 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features and Accessories 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Probe Offset 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Check 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Basics
Operating Basics 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Non-destructive Input Voltage 21. . . . . . . . . . . . . . . . .
Input Linear Dynamic Range 21. . . . . . . . . . . . . . . . . . . . . . . . . . .
Ground Lead Length 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Helpful Hints 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low-inductance Grounding 25. . . . . . . . . . . . . . . . . . . . . . . . . . . .
SureFoot Grounding 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Probe Tip Test Points 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Probe Tip Stabilization 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications
Table of Contents
ii P6245 Instruction Manual
List of Figures
Figure 11: Dynamic and Offset Limitations 18. . . . . . . . . . . . . .
Figure 12: Probe Functional Check Connections 19. . . . . . . . . .
Figure 21: Waveform Distortion from Ground Lead Length 22.
Figure 22: Ground Lead Equivalent Circuit 23. . . . . . . . . . . . . .
Figure 23: Low-inductance Grounding 25. . . . . . . . . . . . . . . . . .
Figure 24: Using a SureFoot Adapter for Grounding 26. . . . . . .
Figure 25: Using a Probe Tip as a Test Point 27. . . . . . . . . . . . .
Figure 26: Probe Tip Stabilizing Notch 28. . . . . . . . . . . . . . . . . .
Figure 31: Typical Bandwidth 33. . . . . . . . . . . . . . . . . . . . . . . . .
Figure 32: Typical Voltage Derating vs. Frequency 33. . . . . . . .
Figure 33: Typical Linearity Error vs VIN 34. . . . . . . . . . . . . . .
Figure 34: Typical Input Impedance vs. Frequency 34. . . . . . . .
Figure 35: Typical Phase vs. Frequency 35. . . . . . . . . . . . . . . . .
P6245 Instruction Manual iii
General Safety Summary
Review the following safety precautions to avoid injury and prevent
damage to this product or any products connected to it.
Only qualified personnel should perform service procedures.
Injury Precautions
Avoid Electric Overload
To avoid electric shock or fire hazard, do not apply a voltage to a
terminal that is outside the range specified for that terminal.
Do Not Operate Without Covers
To avoid electric shock or fire hazard, do not operate this product
with covers or panels removed.
Do Not Operate in Wet/Damp Conditions
To avoid electric shock, do not operate this product in wet or damp
conditions.
Do Not Operate in Explosive Atmosphere
To avoid injury or fire hazard, do not operate this product in an
explosive atmosphere.
General Safety Summary
iv P6245 Instruction Manual
Product Damage Precautions
Do Not Operate With Suspected Failures
If you suspect there is damage to this product, have it inspected by
qualified service personnel.
Do Not Immerse in Liquids
Clean the probe using only a damp cloth. Refer to cleaning
instructions.
Safety Terms and Symbols
Terms in This Manual
These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that
could result in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that
could result in damage to this product or other property.
P6245 Instruction Manual v
Manual Organization
User Information
This section contains the information necessary to install and use the
P6245.
HGetting Started
This section contains the product description, description of
accessories, probe setup configuration, and how to check the probe
for normal operation.
HOperating Basics
This section contains basic information and operating suggestions for
optimal probe performance
HSpecifications
Service Information
This section contains the information necessary to maintain and
service the P6245.
HTheory of Operation
HPerformance Verification
HAdjustments
HMaintenance
HTroubleshooting
Replaceable Parts List
Manual Organization
vi P6245 Instruction Manual
Getting Started
P6245 Instruction Manual 1–1
Product Description
The Tektronix P6245 is a 1.5 GHz (probe only), 10X active FET
probe with less than 1 pF input capacitance. The P6245s low input
capacitance and high input resistance minimize circuit loading over a
wide bandwidth range. The P6245s small profile and low-mass head
makes probing crowded circuits by hand fast and easy. The accessory
tips and adapters enable the P6245 to be used on a wide variety of
circuit architectures.
The P6245 is powered through a TEKPROBE interface between the
probes compensation box and the oscilloscope. The P6245 may be
used with non-TEKPROBE oscilloscopes and instruments by using
the optional Tektronix 1103 Probe Power Supply.
In order to fully appreciate the probes capabilities, please read the
Getting Started and Operating Basics sections of this manual.
Standard Accessories
The P6245 is shipped with the following standard accessories:
Hstandard probe tips
HSureFoot adapter probe tips
HSMT KlipChip microcircuit test leads
HY-lead adapter
Hright-angle adapter
Hsignal-ground adapters
Hthree- and six-inch ground leads
Hlow-inductance ground lead
Hmarker rings
HInstruction Manual
Product Description
12P6245 Instruction Manual
For service information, refer to the service section beginning at the
yellow page.
For part number information for standard and optional accessories,
refer to the Replaceable Parts section of this manual.
Customer Support
To help you get the best performance from your probe, Tektronix
offers the following customer support services:
Operational Support
If you need assistance using your probe, please call our Customer
Support Center at 1-800-TEK-WIDE (1-800-835-9433), extension
2400. If you are outside the United States or Canada, please contact
your nearest Tektronix Service Center.
Service Support
Should your probe need repair that is beyond that supported by this
manual, please contact your nearest Tektronix Service Center.
Sales Support
To order optional equipment and accessories, call the Tektronix
National Marketing Center at 1-800-426-2200. If you are outside the
United States or Canada, please contact your nearest Tektronix
Service Center.
P6245 Instruction Manual 13
Features and Accessories
The P6245 is provided with several features and accessories designed
to make probing and measurement a simpler task. Please take a
moment to familiarize yourself with these items and their uses.
Probe Tip
Socket
Ground
Socket
Stabilization
Notch
Probe Head Assembly. The probe head is
designed for ease of use and high performance.
Its small size makes it easy to handle in tight
areas.
The probe tip socket is sized to easily press onto
0.025 inch pins for direct access. The ground
socket provides a short ground path for high
fidelity ground connections.
The stabilization notch permits you to use
adjacent pins to reduce stresses on the probe
and pins. See pages 1–6 and 2–8 for more
information.
TEKPROBE Interface. The TEKPROBE
interface provides a communication path between
the probe and the oscilloscope. Contact pins
provide power, signal, offset, and probe
characteristic data transfer. See page 4–2 for
more information.
If your oscilloscope does not support the
TEKPROBE interface, you can use the optional
1103 probe power supply as an effective
interface. Contact your local Tektronix representa-
tive for more information.
Push-In Probe Tip
Push-in Probe Tip. Use the push-in probe tip
for general purpose probing by hand. The tip may
also be used as a temporary test point. See page
2–7 for more information.
The push-in probe tip may also be used with the
other socketed leads and adapters.
Features and Accessories
14P6245 Instruction Manual
Installing the Push-in Probe Tip. Attach the
push-in probe tip by seating the tip into the probe
tip socket and pushing the tip in until it is seated.
Either end of the tip may be used.
Do not force the tip. Also, be careful not to poke
yourself with the sharp probe-tip. To remove the
tip, gently grab the tip with small pliers and pull
the tip out.
SureFoot probe tip. The SureFoot tip is an
integral probe tip and miniature guide that
enables fault-free probing of fine-pitch SMD
packages. Attach the SureFoot adapters the
same way as the push-in probe tips. They can be
used with any of the socketed accessory leads.
The yellow, 0.050 inch SureFoot tip is compatible
with 50 mil JEDEC packages such as SOIC,
PLCC, CLCC, etc.
The blue, 0.025 inch SureFoot tip is compatible
with 0.65 mm JEDEC and EIAJ packages.
The red, 0.5 mm SureFoot tip is compatible with
EIAJ packages.
Right Angle
Adapter
Right-angle adapter. Use the right-angle
adapter for low-profile probing of 0.025 inch
diameter square pins.
The right-angle adapter allows the P6245 to lie
flat against a circuit board. This enables probing
in vertical circuits such as computer or commu-
nications backplanes, or in tight areas such as
between circuit cards.
The right-angle adapter can be used directly with
the probe head, or attached to the Y-lead adapter
or ground leads.
The right-angle adapter is attached the same way
as the push-in probe tip, and can be easily
removed by hand.
Features and Accessories
P6245 Instruction Manual 15
Y-lead
Adapter
Y-lead adapter. Use the Y-lead adapter to
extend the physical reach of the probe and
ground when necessary. The Y-lead adapter
accepts any of the probe tips or adapters, and
can be pushed directly onto 0.025 inch pins.
When selecting the grounding connection,
maintain as short a ground path as possible.
Refer to page 22 for more information.
To attach the Y-lead adapter, gently press the
lead pins into the probe head tip and ground
receptacles. Using the black lead for ground is
recommended.
3 and 6 inch ground leads. Use the three- and
six-inch ground leads for general probing. The
socketed end of the leads may be connected to
any of the probe tips and adapters, or fitted onto
0.025 inch pins.
To attach the ground leads, press and rotate the
lead pin connector into the ground socket on the
probe head. The lead may be removed by simply
pulling the pin out by hand.
When selecting the grounding connection,
maintain as short a ground path as possible.
Refer to page 22 for more information.
Low-inductance ground lead. Use the
low-inductance ground adapter to substantially
reduce ground lead inductance. Because the
ground lead simply touches the ground reference,
you can easily move the probe to different points
on the device under test.
To attach, press the ground lead into the probe
head gound socket.
When selecting the grounding connection,
maintain as short a ground path as possible.
Refer to page 22 for more information.
Features and Accessories
16P6245 Instruction Manual
Signal Ground
Adapter
FlexLead
Adapter
SignalGround Adapter. The signal-ground
adapter is ideal for use with signal/ground pairs
on 0.100 inch header pins (such as FlexLead
adapters).
Attach the signal-ground adapter by gently
pressing it into the ground socket on the probe
head.
Be sure to use the stabilization notch whenever
possible. See page 28 for further details.
KlipChip
Y-lead
Adapter
SMT KlipChip. Use the SMT KlipChip test
clips to access fragile, dense circuitry.
KlipChip test clips can be connected to the Y-lead
or three- or six-inch ground leads. Simply press
the lead socket into the KlipChip handle.
The KlipChip body freely turns, allowing better
probe orientation. To reduce stress and provide a
lower profile on components being tested, the
flexible sleeve of the KlipChip bends up to a
35 degree angle.
Color Marker
Bands Color Marker Bands. Attach matching pairs of
the color marker bands onto the cable at the head
and compensation box of each probe. The marker
bands enable quick verification of which probe is
connected to which instrument channel.
P6245 Instruction Manual 17
Configuration
The P6245 provides the oscilloscope with the probe model number,
serial number, and attenuation factor. When connected to a
TEKPROBE oscilloscope, display readouts are corrected for the
probe attenuation factor, the instrument input is set to 50 W, and the
coupling is set to DC.
CAUTION. Do not attempt to install the P6245 on a non-TEKPROBE
connector. Damage to the probe and connector may result. If your
oscilloscope does not support the TEKPROBE interface, use the
optional Tektronix 1103 Probe Power Supply.
If the P6245 is used with the Tektronix 1103 Probe Power Supply, be
sure to have a 50 W termination at the oscilloscope. Also, set the
oscilloscope channel coupling to DC.
The probe offset control is controlled by the oscilloscope. If the
oscilloscope used does not support the TEKPROBE interface, the
offset controls on the optional Tektronix 1103 Probe Power Supply
can be used.
Probe Offset
The probe offset is adjustable to permit operation within the probes
linear range. Using the offset to cancel DC signal components
enables optimal probe performance. See Figure 11 on page 18.
NOTE. See your oscilloscope manual for specific instructions on its
operation and offset control.
Configuration
18P6245 Instruction Manual
To set the probe offset, follow these steps:
1. Set the oscilloscope coupling to GND.
2. Use the vertical position control to set a zero reference level on
the oscilloscope display.
3. Set the oscilloscope coupling to DC and 5 V/div.
4. Attach the probe to the circuit.
5. Adjust the probe offset to bring the trace to the oscilloscope zero
reference.
6. Change the volts/division setting to the desired range, adjusting
the offset to keep the trace on the zero reference level.
NOTE. The P6245 has a ±10 V offset range. The linear operating
range is ±8 V. See Figure 1–1. Also, see page 2–1 for more
information.
If cursors are used on a TEKPROBE oscilloscope, the zero reference
will be at the probe offset voltage.
0 V
+15 V
15 V
+8 V
8 V
+10 V
10 V
Nonoperating Range (+15 V Maximum Non-destructive Input Voltage )
+10 V
10 V
Nonoperating Range (15 V Maximum Non-destructive Input Voltage )
Maximum Offset RangeMaximum AC Signal Amplitude
Figure 11: Dynamic and Offset Limitations
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212

Tektronix P6245 Le manuel du propriétaire

Taper
Le manuel du propriétaire