Tektronix P6245 Manuel utilisateur

xx

P6245

1.5 GHz 10X Active Probe

*P070899505*

070-8995- 05

Instruction Manual

Manue l d’utilisation

Benutzerhandbuch

Manua l de instrucciones

P6245

1.5 GHz 10X Active Probe

ZZZ

Instruction Manual

xx

www.tektronix.com

070-8995-05

owned by Tektronix or its subsidiaries or suppliers, and are protected by

national copyri ght l aws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and

pending. Informati on in this publication supercedes that in all previously

published materi al. Specifications and price change privi leges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

H In North America, ca ll 1-800-833-9200.

H Worldwide, visit www.tektronix.com to find contacts in your area.

Warranty

Tektronix warrants that this produ

ct w ill be free from defects in materials and

workmanship for a period of one (1) year from the date of shipment. If any such product

proves defective during this w

arranty period, Tektronix, at its option, either will repair

the defective product without charge for parts and labor, or w ill provide a replacement

in exchange for the defective

product. Parts, modules and replacement products used by

Tektronix for warranty work may be new or reconditioned to like new performance. All

replaced parts, modules and

products become the property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the

defect before the expiration of the warranty period and make suitable arrangements for the

performance of service. Customer shall be responsible for packaging and shipping the

defective product to the service center designated by Tektronix, with shipping charges

prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to

a location within t he country in which the Tektronix service center is located. Customer

shall be responsible for paying all shipping charges, duties, taxes, and any other charges

for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or

improper or inadequate maintenance a nd care. Tektronix shall not be obligated to furnish

service under this warranty a) to repair damage resulting from attempts by personnel other

than Tektronix representatives to install, repair or service the product; b) to repair damage

resulting from improper use or connection to incompatible equipment; c) to repair any

damage or malfunction c aused by the use of non-Tektronix supplies; or d) to service a

product that has been modiﬁed or integrated with other products w hen the effect of such

modiﬁcation or integration increases the time or difﬁculty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE

PRODUCT I

N L IEU OF A NY OTHER WARRANTIES, EXPRESS OR IMPLIED.

TEKTRONIX AND ITS VENDORS DISCLAIM AN Y IMPLIED WARRANTIES OF

MERCHAN

TABILITY OR FITN ESS FOR A PARTICULAR PURPOSE. TEKTRONIX’

RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE

SOLE AN

D EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR

BREACH OF THIS WARRANTY. TEK TRONIX AND ITS VENDORS W ILL NOT BE

LIABL

E FOR AN Y INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VEN DOR H AS

ADV

ANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

[W2 – 15AUG04]

P6245 Instruction Manual

i

Table of Contents

Getting Started

Product Description 1--1.................................

Standard Accessories 1--1.................................

Customer Support 1--2...................................

Features and Accessories 1--3.............................

Configuration 1--7......................................

Probe Offset 1--7........................................

Functional Check 1--9...................................

Operating Basics

Operating Basics 2--1...................................

Maximum Non-destructive Input Voltage 2--1.................

Input Linear Dynami c Ra nge 2--1..........................

Ground Lead Length 2--2.................................

Helpful Hints 2--5......................................

Low-inductance Grounding 2--5............................

SureFoot™ Grounding 2--6................................

Probe Tip Test Points 2--7.................................

Probe Tip Stabilization 2--8...............................

Specifications

Table of Contents

ii

P6245 Instruction Manual

List of Figures

Figure 1 --1: Dynamic and Offset Limitations 1--8..............

Figure 1--2: Probe Functional Check Connecti ons 1--9..........

Figure 2--1: Wave form Distort ion from Ground Le ad Length 2--2.

Figure 2--2: Ground Lead Equivalent Circ uit 2--3..............

Figure 2--3: Low-inductance Grounding 2--5..................

Figure 2--4: Using a SureFoot Adapter for Grounding 2--6.......

Figure 2--5: Using a Probe Tip as a Test Point 2--7.............

Figure 2 --6: Probe Tip Stabilizing Notch 2--8.................

Figure 3--1: Typical Bandwidth 3--3.........................

Figure 3--2: Typical Voltage Derating vs. Frequenc y 3--3........

Figure 3--3: Typic al Linearity Error vs VIN 3--4...............

Figure 3--4: Typical Input Impedance vs. Frequency 3--4........

Figure 3--5: Typical Phase vs. Frequency 3--5.................

P6245 Instruction Manual

iii

General Safety Summary

Review the following safety precautions to avoid i njury and prevent

damage to this product or a ny products connected to it.

Only qualified personnel should perform service procedures.

Injury Precautions

Avoid Electric Overload

To avoid electric shock or fire hazard, do not apply a voltage to a

terminal that is outside the range specified for that terminal.

Do Not Operate Without Covers

To avoid electric shock or fire hazard, do not operate this product

with covers or panels remove d.

Do Not Operate in Wet/Damp Conditions

To avoid electric shock, do not operate this product in wet or damp

conditions.

Do Not Operate in Explosive Atmosphere

To avoid injury or fire hazard, do not operate this product in an

explosive atmosphere .

General Safety Summary

iv

P6245 Instruction Manual

Product Damage Precautions

Do Not Operate With Suspected Fai lures

If you suspect there is damage to this product, have it inspec ted by

qualified servic e pe rsonnel.

Do Not Immerse in Liquids

Clean the probe using only a damp cloth. Refer to cleaning

instructions.

Safety Terms and Symbols

Terms in This Manual

These terms may appear in this manual:

WARNING. Warning statements identify condit ions or practices that

could result in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that

could result in damage to this product or other property.

P6245 Instruction Manual

v

Manual Organization

User Information

This section contains the information necessary to install and use the

P6245.

H Getting Started

This section contains the product description, description of

accessories, probe setup configuration, and how to check the probe

for normal operati on.

H Operating Basics

This section contains basic information and ope rating suggestions for

optimal probe performance

H Specifications

Service Information

This section contains the information necessary to maintain and

service the P6245.

H Theory of Operation

H Performance Verification

H Adjustments

H Maintenance

H Troubleshooting

Replaceable Parts List

Manual Organization

vi

P6245 Instruction Manual

Getting Started

P6245 Instruction Manual

1-1

Product Description

The Tektronix P6245 is a 1.5 GHz (probe only), 10X active FET

probe with less than 1 pF input capacitance. The P6245’s low input

capacita nce and high input resistance minimize circuit loading over a

wide bandwidth range. The P6245’s small profile and low-mass head

makes probing crowded circuits by hand fast and easy. The accessory

tips and adapters ena ble the P6245 to be used on a wide variety of

circuit architectures.

The P6245 is powered through a TEKPROBE interface be tween the

probe’s compensation box and the oscilloscope. The P6245 may be

used with non-TEKPROBE oscilloscopes and instruments by using

the optional Tektronix 1103 Probe Power Supply.

In order to fully appreciate the probe’s capabilities, please read the

Getting Started and Operating Basics sections of this manual.

Standard Accessories

The P6245 is shipped with the following standa rd accessories:

H standard probe tips

H SMT KlipChip™ microcircuit test leads

H Y-lead adapter

H right-angle ada pter

H signal-ground adapters

H three- and six-inch ground l eads

H low-inductance ground lead

H marker rings

H Instruction Manual

For part number information for standard and optional accessories,

refer to the Replaceable Parts section of this manual.

Product Description

1-2

P6245 Instruction Manual

Customer Support

To help you get the best performance from your probe, Tektronix

offers the following customer support services:

Operational Support

If you need assistance using your probe, please call our Custome r

Support Center at 1-800-TE K-WIDE (1-800-835-9433), e xtension

2400. If you are outside the United States or Canada, please contact

your nearest Tektronix Service Center.

Service Support

Should your probe need repair t hat is beyond that supported by this

manual, ple ase contact your nearest Tektronix Service Ce nter.

Sales Support

To order optional equipment and accessories, call the Tektronix

National Marketing Center at 1-800-426-2200. If you are outside the

United States or Canada , pl ease contact your nea rest Tektronix

Service Center.

P6245 Instruction Manual

1-3

Features and Accessories

The P6245 is provided with several features and accessories designe d

to make probing and measurement a simpler task. Please take a

moment to familiarize yourself with the se items and their uses.

Probe Tip

Socket

Ground

Socket

Stabilization

Notch

Probe Head Assembly. The probe head is

designed for ease of use and high performance.

Its small size makes it easy to handle in tight

areas.

The probe tip socket is sized to easily press onto

0.025 inch pins for direct access. The ground

socket provides a short ground path for high

fidelity ground connections.

The stabilization notch permits you to use

adjacent pins to reduce stresses on the probe

and pins. See pages 1--5 and 2--8 for more

information.

TEKPROBE™ Interface. The TEKPROBE

interface provides a communication path between

the probe and the oscilloscope. Contact pins

provide power, signal, offset, and probe

characteristic data transfer. See page 4--2 for

more information.

If your oscilloscope does not support the

TEKPROBE interface, you can use the optional

1103 probe power supply as an effective

interface. Contact your local Tektronix representa -

tive for more information.

Push-In Probe Tip

Push-in Probe Tip. Use the push-in probe tip

for general purpose probing by hand. The tip may

also be used as a temporary test point. See page

2--7 for more information.

The push-in probe tip may also be used with the

other socketed leads and adapters.

Features and Accessories

1-4

P6245 Instruction Manual

Installing the Push-in Probe Tip. Attach the

push-in probe tip by seating the tip into the probe

tip socket and pushing the tip in until it is seated.

Either end of the tip may be used.

Do not force the tip. Also, be careful not to poke

yourself with the sharp probe-tip. To remove the

tip, gently grab the tip with small pliers and pull

the tip out.

Right Angle

Adapter

Right-angle adapter. Use the right-angle

adapter for low-profile probing of 0.025 inch

diameter square pins.

The right-angle adapter allows the P6245 to lie

flat against a circuit board. This enables probing

in vertical circuits such as computer or commu-

nications backplanes, or in tight areas such as

between circuit cards.

The right-angle adapter can be used directly with

the probe head, or attached to the Y-lead adapter

or ground leads.

The right-angle adapter is attached the same way

as the push-in probe tip, and can be easily

removed by hand.

Y-lead

Adapter

“Y-lead” adapter. Use the Y-lead adapter to

extend the physical reach of the probe and

ground when necessary. The Y-lead adapter

accepts any of the probe tips or adapters, and

can be pushed directly onto 0.025 inch pins.

When selecting the grounding connection,

maintain as short a ground path as possible.

Refer to page 2--2 for more information.

To attach the Y-lead adapter, gently press the

lead pins into the probe head tip and ground

receptacles. Using the black lead for ground is

recommended.

Features and Accessories

P6245 Instruction Manual

1-5

3 and 6 inch ground leads. Use the three- and

six-inch ground leads for general probing. The

socketed end of the leads may be connected to

any of the probe tips and adapters, or fitted onto

0.025 inch pins.

To attach the ground leads, press and rotate the

lead pin connector into the ground socket on the

probe head. The lead may be removed by simply

pulling the pin out by hand.

When selecting the grounding connection,

maintain as short a ground path as possible.

Refer to page 2--2 for more information.

Low-inductance ground lead. Use the

low-inductance ground adapter to substantially

reduce ground lead inductance. Because the

ground lead simply touches the ground reference,

you can easily move the probe to different points

on the device under test.

To attach, press the ground lead into the probe

head gound socket.

When selecting the grounding connection,

maintain as short a ground path as possible.

Refer to page 2--2 for more information.

Signal Ground

Adapter

FlexLead

Adapter

Signal- Ground Adapter. The signal-ground

adapter is ideal for use with signal/ground pairs

on 0.100 inch header pins (such as FlexLead™

adapters).

Attach the signal-ground adapter by gently

pressing it into the ground socket on the probe

head.

Be sure to use the stabilization notch whenever

possible. See page 2-- 8 for further details.

Features and Accessories

1-6

P6245 Instruction Manual

KlipChip

Y-lead

Adapter

SMT KlipChip™. Use the SMT KlipChip test

clips to access fragile, dense circuitry.

KlipChip test clips can be connected to the Y-lead

or three- or six-inch ground leads. Simply press

the lead socket into the KlipChip handle.

The KlipChip body freely turns, allowing better

probe orientation. To reduce stress and provide a

lower profile on components being tested, the

flexible sleeve of the KlipChip bends up to a

35 degree angle.

Color Marker

Bands

Color Marker Bands. Attach matching pairs of

the color marker bands onto the cable at the head

and compensation box of each probe. The marker

bands enable quick verification of which probe is

connected to which instrument channel.

SureFoot™ probe tip (optional). The

SureFoot tip is an integral probe tip and miniature

guide that enables fault-free probing of fine-pitch

SMD packages. Attach the SureFoot adapters the

same way as the push-in probe tips. They can be

used with any of the socketed accessory leads.

The yellow, 0.050 inch SureFoot tip is compatible

with 50 mil JEDEC packages such as SOIC,

PLCC, CLCC, etc.

The blue, 0.025 inch SureFoot tip is compatible

with 0.65 mm JEDEC and EIAJ packages.

The red, 0.5 mm SureFoot tip is compatible with

EIAJ packages.

La page est en cours de chargement...

Tektronix P6245 Manuel utilisateur

Tektronix P6245 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents