DeWalt DCS520B Manuel utilisateur

Marque: DeWalt

Modèle: DCS520B

Taper: Manuel utilisateur

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DCS520

60V Track Saw

Scie sur rail 60V

Sierra de incisión de 60 V

final page size: 8.5 x 5.5 in

ENGLISH

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 15

Español (traducido de las instrucciones originales) 30

ENGLISH

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

If you have any questions or comments about this or

any

DeWALT

tool, call us toll free at:

1-800-4-

DeWALT

(1-800-433-9258).

Fig. A1, A2

Plunge trigger

On/off switch

Main handle

Shoe

Rail adjustment knobs

Bevel scale

Bevel adjustment knob

Depth adjustment knob

Depth scale

Blade

Fig. A1

1312

Front handle

Spindle lock button

Spindle lock lever

Battery pack

Battery release button

Date code

Dust port

Anti-kickback knob

Speed wheel

ENGLISH

GENERAL POWER TOOL SAFETY

WARNINGS



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the

switch is in the off position before connecting to

power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your

finger on the switch or energizing power tools that

have the switch on invitesaccidents.

Fig. A2

ENGLISH

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or

long hair can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-relatedhazards.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power

toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are

caused by poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardoussituation.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

orburns.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool ismaintained.

Safety Instructions for All Saws

Cutting Procedures



DANGER: Keep hands away from cutting area

and the blade. Keep your second hand on

auxiliary handle, or motor housing. If both hands

are holding the saw, they cannot be cut by theblade.

a ) Do not reach underneath the workpiece. The

guard cannot protect you from the blade below

theworkpiece.

b ) Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below theworkpiece.

c ) Never hold piece being cut in your hands or

across your leg. Secure the workpiece to a stable

platform. It is important to support the work properly

to minimize body exposure, blade binding, or loss

ofcontrol.

d ) Hold power tool by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring. Contact with a

"live" wire will also make exposed metal parts of the

power tool "live" and shock theoperator.

e ) When ripping always use a rip fence or straight

edge guide. This improves the accuracy of cut and

reduces the chance of bladebinding.

f ) Always use blades with correct size and shape

(diamond versus round) of arbour holes. Blades

that do not match the mounting hardware of the saw

will run eccentrically, causing loss ofcontrol.

g ) Never use damaged or incorrect blade washers

or bolt. The blade washers and bolt were specially

designed for your saw, for optimum performance and

safety ofoperation.

ENGLISH

Further Safety Instructions for All Saws

Kickback Causes and Related Warnings

Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift up

and out of the workpiece toward the operator;

• When the blade is pinched or bound tightly by the kerf

closing down, the blade stalls and the motor reaction

drives the unit rapidly back toward the operator;

• If the blade becomes twisted or misaligned in the cut, the

teeth at the back edge of the blade can dig into the top

surface of the wood causing the blade to climb out of the

kerf and jump back toward theoperator.

Kickback is the result of saw misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

a ) Maintain a firm grip with both hands on the saw

and position your arms to resist kickback forces.

Position your body to either side of the blade,

but not in line with the blade. Kickback could cause

the saw to jump backwards, but kickback forces can

be controlled by the operator, if proper precautions

aretaken.

b ) When blade is binding, or when interrupting a

cut for any reason, release the trigger and hold

the saw motionless in the material until the

blade comes to a complete stop. Never attempt

to remove the saw from the work or pull the

saw backward while the blade is in motion or

kickback may occur. Investigate and take corrective

actions to eliminate the cause of bladebinding.

c ) When restarting a saw in the workpiece, center

the saw blade in the kerf and check that saw

teeth are not engaged into the material. If saw

blade is binding, it may walk up or kickback from the

workpiece as the saw isrestarted.

d ) Support large panels to minimize the risk of

blade pinching and kickback. Large panels tend

to sag under their own weight. Supports must be

placed under the panel on both sides, near the line of

cut and near the edge of thepanel.

e ) Do not use dull or damaged blades. Unsharpened

or improperly set blades produce narrow kerf causing

excessive friction, blade binding andkickback.

f ) Blade depth and bevel adjusting locking levers

must be tight and secure before making cut. If

blade adjustment shifts while cutting, it may cause

binding andkickback.

g ) Use extra caution when making a “plunge

cut” into existing walls or other blind areas.

The protruding blade may cut objects that can

causekickback.

Safety Instructions for Plunge-Type Saws

Guard Function

a ) Check guard for proper closing before each use.

Do not operate the saw if guard does not move

freely and enclose the blade instantly. Never

clamp or tie the guard with the blade exposed. If

saw is accidentally dropped, guard may be bent.

Check to make sure that guard moves freely and does

not touch the blade or any other part, in all angles

and depths ofcut.

b ) Check the operation and condition of the guard

return spring. If the guard and the spring are not

operating properly, they must be serviced before

use. Guard may operate sluggishly due to damaged

parts, gummy deposits, or a build-up ofdebris.

c ) Assure that the base plate of the saw will not

shift while performing the “plunge cut” when

the blade bevel setting is not at 90°. Blade shifting

sideways will cause binding and likelykickback.

d ) Always observe that the guard is covering the

blade before placing saw down on bench or

floor. An unprotected, coasting blade will cause

the saw to walk backwards, cutting whatever is

in its path. Be aware of the time it takes for the blade

to stop after switch isreleased.

Additional Safety Instructions for All Saws

with Riving Knife

Riving Knife Function

a ) Use the appropriate riving knife for the blade

being used. For the riving knife to work, it must be

thicker than the body of the blade but thinner than

the tooth set of theblade.

b ) Adjust the riving knife as described in this

instruction manual. Incorrect spacing, positioning

and alignment can make the riving knife ineffective in

preventingkickback.

c ) For the riving knife to work, it must be engaged

in the workpiece. The riving knife is ineffective in

preventing kickback during shortcuts.

d ) Do not operate the saw if riving knife is bent.

Even a light interference can slow the closing rate of

aguard.

Additional Safety Instructions for Plunge-

Type Saws

• Wear ear protectors. Exposure to noise can cause

hearingloss.

• Wear a dust mask. Exposure to dust particles can cause

breathing difficulty and possibleinjury.

• Do not use blades of larger or smaller diameter

than recommended. For the proper blade rating refer

to the technical data. Use only the blades specified in this

manual, complying with EN62841-1.

• Never use abrasive cut-offwheels.

• Do not wear gloves with fingers or loose fitting gloves

duringuse.

• Overheating the tips can damage the blade and also

increase the risk of binding whilecutting.

ENGLISH

Additional Safety Information



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.



WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.



CAUTION: When not in use, place tool on its side

on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be

caught in movingparts.

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

.......................no load speed

n .........................rated speed

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... read all

documentation

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

Your tool uses a

DeWALT

charger. Be sure to read all safety

instructions before using your charger. Consult the chart

at the end of this manual for compatibility of chargers and

batterypacks.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into

a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult

the chart at the end of this manual for compatibility of

batteries andchargers.

• Charge the battery packs only in designated

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

ENGLISH

battery pack can explode in a fire. Toxic fumes and

materials are created when lithium ion battery packs

areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of

a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.



WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark orflame.



WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case

is cracked or damaged, do not insert into the charger.

Do not crush, drop or damage the battery pack. Do

not use a battery pack or charger that has received a

sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be

returned to the service center forrecycling.

Transportation



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do

not place the battery pack in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries

can possibly cause fires if the battery terminals

inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes in

carry-on baggage UNLESS they are properly protected

from short circuits. So when transporting individual

battery packs, make sure that the battery terminals

are protected and well insulated from materials that

could contact them and cause a shortcircuit.

Shipping the

DeWALT

FLEXVOLT™ Battery

The D

WALT FLEXVOLT™ battery has two modes: Use and

Shipping.

Use Mode: When the FLEXVOLT™ battery stands alone or is

in a D

WALT 20V Max* product, it will operate as a 20V Max*

battery. When the FLEXVOLT™ battery is in a 60V Max* or a

120V Max* (two 60V Max* batteries) product, it will operate

as a 60V Max* battery.

Shipping Mode: When

the cap is attached to the

FLEXVOLT™ battery, the

battery is in Shipping Mode.

Strings of cells are electrically

disconnected within the pack resulting in three batteries

with a lower Watt hour (Wh) rating as compared to one

battery with a higher Watt hour rating. This increased

quantity of three batteries with the lower Watt hour rating

can exempt the pack from certain shipping regulations that

are imposed upon the higher Watt hourbatteries.

The battery label indicates two Watt hour ratings (see

example). Depending on how the battery is shipped, the

appropriate Watt hour rating must be used to determine

the applicable shipping requirements. If utilizing the

shipping cap, the pack will be considered 3 batteries at

the Watt hour rating indicated for “Shipping”. If shipping

without the cap or in a tool, the pack will be considered one

battery at the Watt hour rating indicated next to “Use”.

USE: 120 Wh Shipping: 3 x 40 Wh

Example of Use and Shipping Label Marking

For example, Shipping Wh rating might indicate 3 x 40 Wh,

meaning 3 batteries of 40 Watt hours each. The Use Wh

rating might indicate 120 Wh (1 battery implied).

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of

charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge

button. A combination of the three green LED lights will

illuminate designating the level of charge left. When the

level of charge in the battery is below the usable limit, the

fuel gauge will not illuminate and the battery will need to

berecharged.

Fig. B

NOTE: The fuel gauge is only an indication of the charge left

on the battery pack. It does not indicate tool functionality

and is subject to variation based on product components,

temperature and end-userapplication.

For more information regarding fuel gauge battery packs,

please contact call 1-800-4-

DeWALT

(1-800-433-9258) or

visit our website www.dewalt.com.

The RBRC® Seal

The RBRC® (Rechargeable Battery

Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-

ion batteries (or battery packs) indicates

that the costs to recycle these batteries

(or battery packs) at the end of their useful life have already

been paid by

DeWALT

. In some areas, it is illegal to place

ENGLISH

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and

the Call2Recycle® program provides an environmentally

consciousalternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other

battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel

cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by

returning the spent nickel cadmium, nickel metal hydride

or lithium-ion batteries to an authorized

DeWALT

service

center or to your local retailer for recycling. You may also

contact your local recycling center for information on

where to drop off the spent battery. RBRC® is a registered

trademark of Call 2 Recycle,Inc.

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• DO NOT attempt to charge the battery pack with

any chargers other than the ones in this manual.

The charger and battery pack are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging

DeWALT

rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the greater the capacity

of the cable, that is, 16 gauge has more capacity than 18

gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using

more than one extension to make up the total length,

be sure each individual extension contains at least the

minimum wire size. The following table shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or

place the charger on a soft surface that might block

the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top

and the bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.



WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock mayresult.



WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the

battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service

center forrecycling.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable battery packs.

Other types of batteries may overheat and burst

resulting in personal injury and propertydamage.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting toclean.

ENGLISH

Charging a Battery (Fig. C)

1. Plug the charger into an appropriate outlet before

inserting batterypack.

Fig. C

2. Insert the battery pack

14

into the charger, making sure

the battery pack is fully seated in the charger. The red

(charging) light will blink continuously indicating that

the charging process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is

fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger,

push the battery release button

15

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-

ion battery packs, charge the battery pack fully before

firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

DCB101

Charging

Fully Charged

Hot/Cold Pack Delay

Problem Pack or Charger

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

Charging

Fully Charged

Hot/Cold Pack Delay*

* DCB107, DCB112, DCB113, DCB115, DCB118, DCB132:

The red light will continue to blink, but a yellow indicator

light will be illuminated during this operation. Once the

battery pack has reached an appropriate temperature, the

yellow light will turn off and the charger will resume the

chargingprocedure.

The compatible charger(s) will not charge a faulty battery

pack. The charger will indicate faulty battery pack by

refusing to light or by displaying a problem pack or charger

blinkpattern.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and

battery pack to be tested at an authorized servicecenter.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan

designed to cool the battery pack. The fan will turn on

automatically when the battery pack needs to becooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of thecharger.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against

overloading, overheating or deepdischarge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the lithium-

ion battery pack on the charger until it is fullycharged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

These chargers are designed to be wall mountable or to

sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet,

and away from a corner or other obstructions which may

impede air flow. Use the back of the charger as a template

for the location of the mounting screws on the wall. Mount

the charger securely using drywall screws (purchased

separately) at least 1" (25.4 mm) long, with a screw head

diameter of 0.28–0.35" (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32" (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non-metallic brush. Do not use water or

any cleaningsolutions.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18° – 24°C). DO NOT charge

ENGLISH

the battery pack in an air temperature below +40°F

(+4.5°C), or above +104°F (+40°C). This is important

and will prevent serious damage to the batterypack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out the

lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

4. The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may

also charge a partially used pack whenever you desire

with no adverse effect on the batterypack.

5. Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Always

unplug the charger from the power supply when there

is no battery pack in the cavity. Unplug the charger

before attempting toclean.

6. Do not freeze or immerse the charger in water or any

otherliquid.

Storage Recommendations

1. The best storage place is one that is cool and dry, away

from direct sunlight and excess heat orcold.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool dry place out of the

charger for optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be

recharged beforeuse.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (FIG. A1, A2)



WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

Refer to Figure A at the beginning of this manual for a

complete list ofcomponents.

INTENDED USE

The DCS520 60V track saw is designed for professional

sawing of woodproducts.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

This heavy-duty track saw is a professional power tool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Bevel Adjustment (Fig. A1)

The bevel angle can be adjusted between 0° and 47°.

1. Loosen the bevel adjustment knobs

7

2. Set the bevel angle by tilting the saw shoe

4

until the

mark indicates the desired angle on the bevel scale

6

3. Tighten the bevel adjustment knobs

7

Changing the Saw Blade (Fig. A1, D, E)

NOTE: It is not necessary to remove the outer blade cover

23

to change theblade.

1. Remove the batterypack.

2. Press the spindle lock button

12

3. Press the track saw down until it stops (blade

changeposition).

4. Turn the spindle lock lever

13

clockwise until itstops.

5. Hold the spindle lock lever

13

down and using the hex

wrench found in the front handle

11

, rotate the blade

until the lock position isfound.

NOTE: The blade

10

is now locked and cannot be turned

byhand.

Fig. D

ENGLISH

6. Use the hex wrench to turn the blade clamping screw

24

counter-clockwise toremove.

7. Remove the outer flange

25

and used blade

10

. Place

the new blade on the inner flange

26

8. Replace the outer flange

25

and blade clamping screw

24

. Turn the screw clockwise byhand.

NOTE: The direction of rotation of the saw blade and the

rotation of the track saw MUST be thesame.

9. Tighten the blade clamping screw firmly using the

hexwrench.

10. Release and turn the spindle lock lever

13

counter-

clockwise until itstops.

11. Move the track saw back to topposition.

12. Push the plunge trigger

1

forward, to take the saw out

of blade changemode.

Fig. E

5/64”-1/8”

(2–3 mm)

5/64”-1/8”

(2–3 mm)

Adjusting the Riving Knife (Fig. A1, D, E)

For the correct adjustment of the riving knife

21

, refer

to FigureE. Adjust the clearance of the riving knife after

changing the saw blade or whenevernecessary.

1. Follow Changing the Saw Blade steps 1–5.

2. Loosen the riving knife adjustment screw

22

with a hex

wrench and set the riving knife as shown in FigureE.

3. Tighten the riving knife adjustment screw

22

4. Turn the spindle lock lever

13

counter-clockwise until

itstops.

5. Move the track saw back to topposition.

6. Push the plunge trigger

1

forward, to take the saw out

of blade changemode.

Depth of Cut Adjustment (Fig. F)

The cutting depth can be set at 0–2.3” (0–59 mm) without

guide rail attached; with the guide rail attached: 0–2.2”

(0–55 mm).

1. Loosen the depth adjustment knob

8

and move the

pointer to obtain the correct depth ofcut.

2. Tighten the depth adjustment knob

8

NOTE: For optimal results, allow the saw blade to protrude

from the workpiece by about 1/8” (3 mm) (Fig.F).

Fig. F

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Installing and Removing the Battery Pack

(Fig. A1)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack

14

into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide

it into the handle until the battery pack is firmly seated in

the tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button

15

and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

ENGLISH

Proper Hand Position (Fig. G)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the front handle

11

, with the other hand on the main handle

3

Fig. G

Instructions for Use



WARNING: Always observe the safety instructions

and applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Switching On and Off (Fig. A1)

Press the on/off switch

2

to turn the track sawon.

Guiding the Tool (Fig. A1, G, H)



WARNING:

• ALWAYS secure the workpiece in such a manner

that it cannot move whilesawing.

• ALWAYS push the machine forward. NEVER pull

the machine backward towardsyou.

• ALWAYS use the track saw with both hands.

Put one hand on the main handle

3

and the

second hand on the front handle

11

as shown

in FigureG.

• ALWAYS use the clamp to hold the rail to

theworkpiece.

• Use proper hand position to guide the sawproperly.

• The cutting indicator

27

displays the cutting line for 0°

and 47° cuts (without guide rail).

• The blade position indicator

29

shows the blade

position for fullplunge.

• For optimum results, clamp the workpiece bottomup.

Fig. H

Cutting

1. Place the machine with the front part of the saw shoe

4

on theworkpiece.

2. Push the plunge trigger

1

forward, then press the on/

off switch

2

to turn the sawon.

3. Press the saw down to set cutting depth and push it

forward in the cuttingdirection.

Plunge Cuts (Fig. A2)



WARNING: To avoid kickbacks, the following

instructions MUST be observed when plunge cutting:

• Place the machine onto the guide rail

28

and

release the anti-kickback knob

18

by turning it

counter-clockwise.

• Turn the machine on and slowly press the saw

down onto the set cutting depth and push

forward in the cutting direction. The cutting

indicators

27

display the absolute front and the

absolute rear cutting points of the saw blade (dia.

6.5" [165 mm]) at maximum cutting depth and

using the guiderail.

• If kickback happened during the plunge cut, turn

the anti-kickback knob

18

counter-clockwise to

release it from therail.

• When you have finished the plunge cut, turn

the anti-kickback knob

18

clockwise into the

lockposition.

Blades



WARNING: To minimize the risk of eye injury, always

wear ANSI Z87.1 approved eye protection. Carbide

is a hard but brittle material. Foreign objects in the

work piece such as wire or nails can cause tips to

crack or break. Only operate saw when proper saw

blade guard is in place. Mount blade securely in

proper rotation before using, and always use a clean,

sharpblade.



WARNING: Do not cut metal, masonry, glass,

masonry-type planking, cement board, tile or plastic

with thissaw.

A dull blade will cause inefficient cutting, overload on the

saw motor, excessive splintering and increase the possibility

ENGLISH

of kickback. Change blades when it is no longer easy to

push the saw through the cut, when the motor is straining,

or when excessive heat is built up in the blade. It is a

good practice to keep extra blades on hand so that sharp

blades are available for immediate use. Dull blades can be

sharpened in most areas; see SAWS-SHARPENING in the

yellow pages. Hardened gum on the blade can be removed

with kerosene, turpentine, or oven cleaner. Anti-stick coated

blades can be used in applications where excessive build-up

is encountered, such as pressure treated and greenlumber.

Blade Selection (Fig. I)



WARNING: To minimize the risk of kickback and

to ensure proper cutting, the blade selected must

be appropriate for the thickness of the riving

knifeprovided.

The blade supplied with this circular saw is the correct size

for the riving knife supplied with thesaw.

If a different blade is used, check the blade body (plate)

thickness and the blade kerf (cutting) width marked on the

blade or on the blade packaging. The riving knife thickness

must be greater than the body thickness and less than the

kerf width as shown in FigureI.

The riving knife provided with this saw is marked with its

thickness; .067" (1.7 mm). This riving knife should only be

used for blades with a 0.07" (1.8 mm) minimum kerf width

and 0.063" (1.6 mm) maximum bodythickness.

Your

DeWALT

track saw is designed for use with 6–1/2"

(165mm) diameter blades that have a 0.79" (20mm)

diameter bore. Blades must be rated for 6000 rpm operation

(or higher). DO NOT use any abrasivewheels.

Riving knife thickness

Kerf width (width of cut

made by the blade)

Body (or plate) thickness

of the blade

Fig. I

A combination blade is furnished with your saw and is an

excellent blade for all general ripping and crosscutting

operations. Use a fine-tooth blade for cuttingplywood.



WARNING: VISUALLY EXAMINE CARBIDE BLADES

BEFORE USE. REPLACE IFDAMAGED.

Guide Rail System (Fig. A1, J)

The guide rails

28

, which are available in different lengths,

allow for precise, clean cuts and simultaneously protect the

workpiece surface againstdamage.

In conjunction with additional accessories, exact angled

cuts, mitre cuts and ﬁtting work can be completed with the

guide railsystem.

Securing the workpiece with clamps ensures a secure hold

and safeworking.

The guide clearance of the track saw must be very small

for best cutting results and can be set with the two rail

adjustment knobs

5

1. Release the screw inside the rail adjustment knobs

5

adjust theclearance.

2. Adjust the knob until saw locks onrail.

3. Rotate knob back until saw slideseasily.

4. Hold the rail adjustment knob in position and lock the

screwagain.

NOTE: ALWAYS readjust the system for use with otherrails.

Anti-Splinter Guard (Fig. J, K)

The guide rail

28

is equipped with an anti-splinter guard

30

, which has to be trimmed before the ﬁrst use.

The anti-splinter guard

30

is situated on each edge of the

guide rail (

28

, Fig. J). The purpose of this anti-splinter guard

is to provide the user with a visible blade cut line while

reducing the chipping that occurs along the workpiece cut

edge duringcutting.

IMPORTANT: ALWAYS read and follow the Guide Rail

System instructions before cutting the splinterguard!

1. Set the speed of the track saw to level7.

2. Place the guide rail

28

on a scrap piece of wood. Use a

clamp to ensure that the guide rail is securely attached

to the workpiece. This will ensureaccuracy.

3. Set the track saw on 13/64” (5 mm) cutdepth.

4. Place the saw on the rear end of the guiderail.

5. Turn the saw on, press it down to the set cutting depth

and cut the anti-splinter guard

30

along the full length

in one continuous operation. The edge of the anti-

splinter guard now corresponds exactly to the cutting

edge of theblade.

To trim the anti-splinter guard on the other side of the

guide rail, remove the saw from the rail and rotate the rail

180°. Repeat steps 1 through 4.

NOTE: If desired, the splinter guard can be bevelled to 45°,

then repeat steps 1 through 4. This allows one side of the

rail for cutting parallel cuts and the other side of the rail is

tuned in for 45° bevel cuts (Fig. K).

NOTE: If the anti-splinter guard is trimmed for parallel

cutting on both sides, then when the unit is bevelled, the

blade will not run true to the edge of the anti-splinter

guard. This is because the pivot point of the unit bevel

is not stationary and the blade moves out when the unit

isbevelled.



WARNING: To reduce the risk of injury, ALWAYS

secure the guide rail with aclamp.

ENGLISH

Fig. J

45˚

Fig. K

0˚

Speed Adjustment (Fig. A2)

The speed can be regulated between 2500 and 4200 rpm

using the speed wheel

19

. This enables you to optimize

the cutting speed to suit the material. Refer to the following

chart for type of material and speedrange.

Type of Material to be Cut Speed Range

Solid wood (hard, soft) 3–7

Chipboards 4–7

Laminated wood, blockboards, veneered and coated boards 2–7

Paper and carton 1–3

Door Cutting (Fig. L)

1. Place the track saw with the outer guard

23

on a clean,

flat floor.

2. Press the shoe

4

with the front side on the door against

the adjusted depthstop.

Fig. L

Dust Extraction (Fig. A2)

Your tool is fitted with a dust port

17



WARNING: DO NOT direct sawdust toward yourself

or others. DO NOT insert foreign objects into the

exhaustopening.



WARNING: ALWAYS connect the track saw to a dust

extractor!



WARNING: ALWAYS use a dust extraction device

designed in accordance with the relevant regulations

regarding dustemission.



WARNING: Static charge may occur if an anti-static

suction hose is notused.

A universal 1-1/4" dust extraction hose can be connected to

the dust port

17

. Check for a tight connection beforeuse.

Dust Duct Cleaning

Depending on your cutting environment, saw dust can clog

the dust duct and may prevent dust from flowing away

from the cutting area properly. With the battery removed,

low pressure air or a large diameter dowel rod can be used

to clear the dust out of the dustduct.

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthis.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

ENGLISH

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

Accessories



WARNING: Since accessories, other than those

offered by

DeWALT

, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories should be used with

thisproduct.

Recommended accessories for use with your tool

are available at extra cost from your local dealer or

authorized service center. If you need assistance in

locating any accessory, please contact

DeWALT

Industrial

Tool Co., 701East Joppa Road, Towson, MD 21286, call

1-800-4-

DeWALT

(1-800-433-9258) or visit our website:

www.dewalt.com.

Repairs

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement, when

applicable) should be performed by a

DeWALT

factory

service center or a

DeWALT

authorized service center.

Always use identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to

faulty materials or workmanship for three years from the

date of purchase. This warranty does not cover part failure

due to normal wear or tool abuse. For further detail of

warranty coverage and warranty repair information, visit

www.dewalt.com or call 1-800-4-

DeWALT

(1-800-433-9258).

This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and

you may have other rights which vary in certain states

orprovinces.

In addition to the warranty,

DeWALT

tools are covered

byour:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,

DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204, DCB204BT, DCB205, DCB606

NOTE: Battery warranty voided if the battery pack is

tampered with in any way.

DeWALT

is not responsible

for any injury caused by tampering and may prosecute

warranty fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your

DeWALT

Power Tool, Laser, or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

(1-800-433-9258) for a freereplacement.

FRANÇAIS

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels ou matériels.



DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des

blessuresgraves.



AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessuresgraves.



ATTENTION: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message propre à la sécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait

pour l’éviter, pourrait poser des risques de dommages matériels.



AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

Pour toute question ou remarque au sujet de cet outil

ou de tout autre outil

DeWALT

, composez le numéro

sans frais : 1-800-4-

DeWALT

(1-800-433-9258).

Français (traduction de la notice d’instructions originale)

Fig. A1, A2

Déclencheur de plongée

Interrupteur marche/arrêt

Poignée principale

Châssis

Boutons de réglage de rail

Échelle de biseau

Bouton de réglage de

biseau

Bouton de réglage de

profondeur

Échelle de profondeur

Lame

Fig. A1

1312

Poignée avant

Bouton de verrouillage

de la broche

Levier de verrouillage de

la broche

Bloc-piles

Bouton de libération du

bloc-piles

Code de datation

Buse de dépoussiérage

Molette anti-rebonds

Régulateur de vitesse

FRANÇAIS

AVERTISSEMENTS DE SÉCURITÉ

GÉNÉRAUX POUR LES OUTILS

ÉLECTRIQUES



AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE

ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur

(avec fil) ou par piles (sans fil).

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une

distraction pourrait en faire perdre la maîtrise à

l’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à

laprise.

b ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des

radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc électrique est plus élevé si votre corps

est mis à laterre.

c ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive.

Ne jamais utiliser le cordon pour transporter,

tirer ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords

tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques

de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à

l’extérieur, se servir d’une rallonge convenant à

cette application. L’utilisation d’une rallonge conçue

pour l’extérieur réduira les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique

est utilisé. Ne pas utiliser d’outil électrique en

Fig. A2

FRANÇAIS

cas de fatigue ou sous l’influence de drogues,

d’alcool ou de médicaments. Un simple moment

d’inattention en utilisant un outil électrique peut

entraîner des blessures corporellesgraves.

b ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position

d’arrêt avant de relier l’outil à une source

d’alimentation et/ou d’insérer un bloc-piles, de

ramasser ou de transporter l’outil. Transporter

un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont

l’interrupteur est à la position de marche risque de

provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver

son équilibre en tout temps. Cela permet

de mieux maîtriser l’outil électrique dans les

situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

4) Utilisation et entretien d’un outil

électrique

a ) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour laquelle il a

étéconçu.

b ) Ne pas utiliser un outil électrique dont

l’interrupteur est défectueux. Tout outil électrique

dont l’interrupteur est défectueux est dangereux et

doit êtreréparé.

c ) Débrancher la fiche de la source d’alimentation

et/ou du bloc-piles de l’outil électrique avant de

faire tout réglage ou changement d’accessoire

ou avant de ranger l’outil. Ces mesures préventives

réduisent les risques de démarrage accidentel de

l’outilélectrique.

d ) Ranger les outils électriques hors de la portée

des enfants et ne permettre à aucune personne

n’étant pas familière avec un outil électrique ou

son mode d’emploi d’utiliser cet outil. Les outils

électriques deviennent dangereux entre les mains

d’utilisateursinexpérimentés.

e ) Entretien des outils électriques. Vérifier si les

pièces mobiles sont mal alignées ou coincées,

si des pièces sont brisées ou présentent toute

autre condition susceptible de nuire au bon

fonctionnement de l’outil électrique. En cas de

dommage, faire réparer l’outil électrique avant

toute nouvelle utilisation. Beaucoup d’accidents

sont causés par des outils électriques malentretenus.

f ) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus

faciles àmaîtriser.

g ) Utiliser l’outil électrique, les accessoires, les

forets, etc. conformément aux présentes

directives en tenant compte des conditions de

travail et du travail à effectuer. L’utilisation d’un

outil électrique pour toute opération autre que celle

pour laquelle il a été conçu estdangereuse.

5) Utilisation et entretien du bloc-piles

a ) Ne recharger l’outil qu’au moyen du chargeur

précisé par le fabricant. L’utilisation d’un chargeur

qui convient à un type de bloc-piles risque de

provoquer un incendie s’il est utilisé avec un autre type

de b loc-piles.

b ) Utiliser les outils électriques uniquement avec

les blocs-piles conçus à cet effet. L’utilisation de

tout autre bloc-piles risque de causer des blessures ou

unincendie.

c ) Lorsque le bloc-piles n’est pas utilisé, le tenir

éloigné des objets métalliques, notamment

des trombones, de la monnaie, des clés, des

clous, des vis ou autres petits objets métalliques

qui peuvent établir une connexion entre les

deux bornes. Le court-circuit des bornes du bloc-piles

risque de provoquer des brûlures ou unincendie.

d ) En cas d’utilisation abusive, le liquide peut gicler

hors du bloc-piles; éviter tout contact avec ce

liquide. Si un contact accidentel se produit, laver

à grande eau. Si le liquide entre en contact avec

les yeux, obtenir également des soins médicaux.

Le liquide qui gicle hors du bloc-piles peut provoquer

des irritations ou desbrûlures.

6) Réparation

a ) Faire réparer l’outil électrique par un réparateur

professionnel en n’utilisant que des pièces de

rechange identiques. Cela permettra de maintenir

une utilisation sécuritaire de l’outilélectrique.

FRANÇAIS

Consignes de sécurité propres à toutes les

scies

Procédures de coupe



DANGER : éloigner les mains des zones et

organes de coupe. Maintenir la deuxième main

sur la poignée auxiliaire ou le boîtier du moteur.

Lorsque la scie est maintenue à deux mains, les risques

de se couper avec la lame sontlimités.

a ) Ne pas envoyer les mains sous la pièce à

travailler. Sous la pièce, le dispositif de protection ne

peut vous protéger de lalame.

b ) Ajuster la profondeur de coupe à l’épaisseur de

la pièce à travailler. Un peu moins d’une longueur

de dent de scie devrait être visible sous la pièce

àtravailler.

c ) Ne jamais maintenir la pièce à découper avec les

mains ou les jambes. Arrimer la pièce à travailler

à une plateforme stable. Il est important de

maintenir le projet correctement pour minimiser tout

risque de dommages corporels, de pincement de lame,

ou de perte de contrôle de l’outil.

d ) Tenir l’outil électrique par les surfaces isolées

prévues à cet effet pendant toute utilisation où

l’organe de coupe pourrait entrer en contact

avec des fils électriques cachés. Tout contact avec

un fil sous tension met les parties métalliques exposées

de l’outil sous tension et électrocutera l’utilisateur.

e ) Pour toute coupe longitudinale, utiliser

systématiquement un guide longitudinal ou un

guide de chant. Cela accroitra la précision de coupe

et réduira les risques de grippage delame.

f ) Utiliser systématiquement des lames de taille

adéquate avec un alésage central façonné

(diamant par rapport à arrondi). Toute lame

non conçue pour la ferrure de fixation de la scie

fonctionnera de manière excentrique et provoquera la

perte de contrôle de l’outil.

g ) Ne jamais utiliser de rondelles ou de boulons de

lame endommagés ou inadéquats. Les rondelles

et boulons de lame ont été spécialement conçus

pour cette scie, pour optimiser ses performances et sa

sécurité d’emploi.

Consignes additionnelles de sécurité

propres à toutes les scies

Causes des rebonds et avertissements

afférents

Les rebonds sont la conséquence soudaine d’un grippage

ou d’une lame mal alignée qui font que la scie rebondit

brutalement hors de la pièce à travailler vers l’utilisateur.

• Lorsque la lame reste pincée ou bloquée dans le trait de

scie, elle cale et le moteur en réaction provoque un rebond

arrière de l’appareil vers l’utilisateur.

• S’il y a torsion de la lame ou si elle sort de la ligne de

coupe, les dents à l’arrière de la lame pourront se planter

dans la surface du bois et faire que la lame sorte du trait

de scie et rebondisse vers l’utilisateur.

Les rebonds proviennent d’une utilisation inadéquate de

l’outil et/ou d’une procédure ou de conditions d’utilisation

incorrectes, et peuvent être évités en prenant les précautions

appropriées détaillées ci-après:

a ) Maintenir la scie fermement à deux mains et

positionner les bras de façon à pouvoir résister

à toute force de rebonds. Positionner le corps

sur l’un des côtés de la lame, mais jamais dans

son alignement. Les rebonds peuvent faire rebondir

la scie en arrière, mais en prenant les précautions

adéquates, les forces de rebonds peuvent être

contrôlées par l’utilisateur.

b ) Lorsqu’il y a grippage de la lame, ou lorsqu’on

interrompt une coupe pour une raison

quelconque, relâcher la gâchette et maintenir

la scie immobile dans le matériau jusqu’à arrêt

complet de la lame. Pour éviter tout rebond,

ne jamais tenter de retirer la scie de la pièce ou

de la tirer vers l’arrière alors que la lame est en

mouvement. Examiner la pièce à travailler et prendre

les mesures qui s’imposent pour éliminer tout risque

degrippage.

c ) Avant de remettre la scie en marche dans la

pièce à travailler, centrer la lame sur le trait

de scie et vérifier que les dents de scie ne sont

pas engagées dans le matériau. Lorsqu’il y a

grippage de la lame, celle-ci pourrait sauter ou faire

un rebond hors du matériau lorsque la scie sera remise

enmarche.

d ) Supporter les grands panneaux pour minimiser

tout risque de grippage de lame et de rebonds.

Les grands panneaux ont tendance à s’affaisser

sous leur propre poids. Le support peut être installé

d’un côté ou de l’autre, sous le panneau, près de la

ligne de coupe et sous les bords externes dupanneau.

e ) Ne pas utiliser de lames émoussées ou

endommagées. Les lames émoussées ou

incorrectement installées produisent des traits de scie

étroits pouvant causer frictions, grippages etrebonds.

f ) Les leviers de verrouillage de profondeur de

lame et de réglage de biseau doivent être

soigneusement serrés avant toute coupe. Si le

réglage de lame venait à changer en cours de coupe, il

y aurait risques de grippage et derebonds.

g ) Prenez des précautions supplémentaires lors de

«coupes en plongée» dans des murs existants

ou dans toute zone à visibilité limitée. La lame

pourrait rencontrer des objets qui pourraient causer

desrebonds.

Consignes de sécurité propres aux scies

pour coupe en plongée

Fonction du carter

a ) Vérifier soigneusement la fermeture du carter

avant toute utilisation. Ne pas utiliser la scie si

le carter ne se déplace pas librement et ne se

referme pas instantanément sur la lame. Ne

jamais arrimer ou attacher le carter en laissant

la lame à nu. Le carter pourrait être endommagé

si la scie venait à tomber. Vérifier que le carter se

déplace librement et ne touche pas la lame ou toute

autre partie de la scie, à tout angle et toute profondeur

decoupe.

La page charge ...

DeWalt DCS520B Manuel utilisateur

Marque: DeWalt

Modèle: DCS520B

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCS520B User manual
español: DeWalt DCS520B Manual de usuario

DeWalt DCS520B Manuel utilisateur

DeWalt DCS520B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents