Maruyama B42 Le manuel du propriétaire

Catégorie
Coupe-herbe
Taper
Le manuel du propriétaire

Ce manuel convient également à

The POWER in Outdoor Power
Completely read and understand this manual PRIOR to using this product.
Lea y entienda este manual a fondo, ANTES de usar este producto.
Lisez complètement et comprenez ce manuel AVANT d'utiliser ce produit.
OWNER'S/ OPERATOR'S MANUAL
MANUAL DEL PROPIETARIO U OPERADOR
MANUEL DU PROPRIETAIRE/ DE L'UTILISATEUR
String Trimmer/ Brushcutter
Recortadora/ Desbrozadora
Coupe-bordures/ Débroussailleuse
B42L/ B42/ B42A
®
— US-1 —
Limited Warranty Statement
All Maruyama commercial/ industrial products are warranted to the original purchaser to be free from defects in material
and workmanship from the date of purchase for the time periods listed as follows:
Lifetime for solid steel driveshaft and ignition coils.
5 years for qualified IRON 5-YR™ commercial, institutional, or industrial use.
1 year for residential or 2 years for commercial use with competitors oil.
90 days for rental use.
Engine - Refer to engine manufacturers warranty statement. Only Maruyama engines are covered by
this limited warranty statement.
Any part of a Maruyama product found to be defective within the applicable warranty period shall, at Maruyama's
option, be repaired or replaced without charge. Warranty consideration is obtained by delivering any Maruyama product
believed to be defective to an Authorized Maruyama Servicing Dealer within the applicable warranty period.
The purchaser shall not be charged for diagnostic labor that leads to the determination that a warranted part is
defective, if the diagnostic work is performed at a Maruyama Dealer.
Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for
regular inspection to the effect of “repair or replace as necessary” shall be warranted for the warranty period. Any
warranted part, which is scheduled for replacement as, required maintenance shall be warranted for the period of time
up to the first scheduled replacement point for that part. Maruyama Mfg. Co., Inc. is liable for damages to other
engine components caused by the failure of a warranted part still under warranty.
The purchaser is responsible for the performance of the required maintenance, as defined by Maruyama Mfg. Co., Inc. in
the Owner's/ Operator's Manual.
EMISSION-RELATED PARTS WARRANTY: In addition to the above warranty coverage, Maruyama Mfg. Co., Inc.
will repair or replace, free of charge, for the original purchaser and each subsequent purchaser any emission-related
part or parts found to be defective in material and workmanship for two (2) years from original retail delivery date.
Emission-related parts are the carburetor assembly, the ignition coil assembly, the ignition rotor, the spark
plug, the catalytic converter and the fuel tank. Any replacement part that is equivalent in performance and
durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of
Maruyama Mfg. Co., Inc.
®
— US-2 —
This warranty does not cover the following:
1. Maintenance items (excluding defects in materials and workmanship) including hoses, spark plugs, starter rope,
air and fuel filters, clutch shoes, vibration isolators, throttle cables and all cutting attach- ments, etc.
2. Extra expenses including shipping and handling, travel, payment for lost time or pay and for any inconvenience
and storage.
3. Alterations or modifications including aftermarket parts not authorized by Maruyama U.S., Inc.
4. Wear, accident, abuse, neglect, misuse, negligence, improper fuels, lubricants, fuel mixtures (when applicable),
or failure to operate or maintain the product in accordance with instructions approved by Maruyama.
Repair or replacement as provided under this warranty is the exclusive remedy of the consumer. Maruyama shall not be
liable for any incidental or consequential damages for breach of any express or implied warranty on these products
except to the extent prohibited by applicable law. Any implied warranty of merchantability or fitness for a particular
purpose on these products is limited in duration to the warranty period as defined in the limited warranty statement.
Maruyama reserves the rights to change or improve the design of the product without notice and does not assume
obligation to update previously manufactured products.
This warranty provides you with specific legal rights, which may vary from state to state.
It is the Owner's and Dealer's responsibility to make sure the Warranty Registration Card is properly filled out and mailed
to Maruyama U.S., Inc. Proof of purchase and registration will be required in order to obtain warranty service.
To locate an Authorized Maruyama Servicing Dealer nearest you, contact:.
Maruyama U.S., Inc.
4770 Mercantile Drive, suite100,
Fort Worth, TX
76137
U.S.A.
(940)383-7400
maruyama@maruyama-us.com
www.maruyama-us.com
— US-3 —
B42L/ B42/ B42A
WARNING:
Operating, servicing and maintaining this product can expose you to chemicals including
engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of
California to cause cancer and birth defects or other reproductive harm. To minimize
exposure, avoid breathing exhaust, service equipment in a well-ventilated area and wear
gloves or wash your hands frequently when servicing this equipment. For more information,
visit on the web at www.P65warnings.ca.gov.
FEDERAL EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The U.S. Environmental Protection Agency (EPA), and Maruyama Manufacturing Company, Inc
. are
pleased to explain the emission control system warranty on your small off-road engine. New 1997 and
later model year small off-road engines must be designed, built and equipped, at the time of sale, to meet the
U.S. EPA regulations for small off-road engines. The equipment engine must be free from defects in materials
and workmanship which cause it to fail to conform with U.S. EPA standards for the first two years of engine
use from the date of sale to the ultimate purchaser. Maruyama Manufacturing Company, Inc. must warrant the
emission control system on your small off-road engine for the period of time listed above provided there has
been no abuse, neglect or improper maintenance of your small off-road engine.
Emission durability of 300 hours.
Your emission control system may include parts such as the carburetor or fuel injection system, the ignition
system, and catalytic converter. Also included may be hoses, belts, and connectors and other emission
related assemblies.
Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your small off-road
engine at no cost to you, including diagnosis (if the diagnostic work is performed at an authorized dealer),
parts, and labor.
MANUFACTURER’S WARRANTY COVERAGE:
The 1997 and later model year small off-road engines are warranted for two years. If any emission-related
part on your engine is defective, the part will be repaired or replaced by Maruyama Manufacturing
Company, Inc. free of charge.
OWNER’S WARRANTY RESPONSIBILITIES:
(a) As the small off-road engine owner, you are responsible for the performance of the required
maintenance listed in your owners/operators manual.
Maruyama Manufacturing Company, Inc. recommends that you retain all receipts covering maintenance
on your small off-road engine, but Maruyama Manufacturing Company, Inc. cannot deny warranty solely
for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. Any
replacement part or service that is equivalent in performance and durability may be used in non-warranty
maintenance or repairs, and shall not reduce the warranty obligations of the engine manufacturer.
(b) As the small off-road engine owner, you should be aware, however, that Maruyama Manufacturing
Company may deny you warranty coverage if your small off-road engine or a part has failed due to
abuse, neglect, improper maintenance or unapproved modifications.
(c) You are responsible for presenting your small off-road engine to a Maruyama Manufacturing Company,
Inc. service center as soon as a problem exists. The warranty repairs should be completed in a
reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact
Maruyama U.S., Inc. at 1-866-783-7400, or warranty@maruyama-us.com.
— US-4 —
COVERAGE
Maruyama Manufacturing Company, Inc. warrants to the ultimate purchaser and each subsequent
purchaser that your small off-road engine will be designed, built and equipped, at the time of sale, to meet all
applicable regulations. Maruyama Manufacturing Company, Inc. also warrants to the initial purchaser and
each subsequent purchaser that your small off-road engine is free from defects in materials and
workmanship which cause the engine to fail to conform with applicable regulations for a period of two years.
The 1997 and later model years, EPA requires manufacturers to small off-road engines for two years.
These warranty periods will begin on the date the small off-road engine is purchased by the initial
purchaser. If any emission-related part on your engine is defective, the part will be replaced by
Maruyama Manufacturing Company, Inc. at no cost to the owner.
Maruyama Manufacturing Company, Inc. shall remedy warranty defects at any authorized Maruyama
Manufacturing Company, Inc. engine dealer or warranty station. Any authorized work done at an
authorized dealer or warranty station shall be free of charge to the owner if such work determines that a
warranted part is defective. Any manufacturer-approved or equivalent replacement part may be used for
any warranty maintenance or repairs on emission-related parts, and must be provided free of charge to the
owner if the part is still under warranty, Maruyama Manufacturing Company, Inc. is liable for damages to
other engine components caused by the failure of a warranted part still under warranty.
EPA considers emission-related warranted parts to include all the parts listed below. These warranted
parts are: the carburetor assembly, the ignition coil assembly, the ignition rotor, the spark plug,
the catalytic converter, and the fuel tank.
MAINTENANCE REQUIREMENTS
The owner is responsible for the performance of the required maintenance as defined by the Maruyama
Manufacturing Company, Inc. in the owner's/operators manual.
LIMITATIONS
This Emission Control System Warranty shall not cover any of the following:
(a) repair or replacement required because of misuse or neglect, lack of required maintenance, repairs
improperly performed or replacements not conforming to Maruyama Manufacturing Company, Inc.
specifications that adversely affect performance and/or durability, and alterations or modifications not
recommended or approved in writing by Maruyama Manufacturing Company, Inc., and
(b) replacement of parts and other services and adjustments necessary for required maintenance at and
after the first scheduled replacement point.
Part II: CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT
CALIFORNIA EXHAUST AND EVAPORATIVE EMISSION CONTROL WARRANTY
STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS
The California Air Resources Board and Maruyama Manufacturing Company, Inc. are pleased to explain the
exhaust and evaporative emissions (“emissions”) control system warranty on your 2019 small off-road
engine. In California, new equipment that use small off-road engines must be designed, built, and equipped to
meet the State’s stringent anti-smog standards. Maruyama Manufacturing Company, Inc. must warrant the
emissions control system on your small off-road engine for the periods of time listed below provided there has
been no abuse, neglect or improper maintenance of your small off-road engine or equipment leading to the
failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-injection system, the ignition
system, catalytic converter, fuel tanks, fuel lines (for liquid fuel and fuel vapors), fuel caps, valves, canisters,
filters, clamps and other associated components. Also included may be hoses, belts, connectors, and other
emission-related assemblies.
The evaporative emission warranty parts list shall include all parts whose failure would increase evaporative
emissions, and may contain, but is not limited to, the following parts: Fuel Tank, Fuel Cap, Fuel Lines (for
liquid fuel and fuel vapors), Fuel Line Fittings, Pressure Relief Valves, Control Valves, Vacuum Control
Diaphragms, Purge Valves, Carburetor Purge Port Connector.
— US-5 —
Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your small off-road
engine at no cost to you including diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COVERAGE:
The exhaust and evaporative emissions control system on your small off-road engine is warranted for two
years. If any emissions-related part on your small off-road engine is defective, the part will be repaired or
replaced by Maruyama Manufacturing Company, Inc.
OWNER’S WARRANTY RESPONSIBILITIES:
As the small off-road engine owner, you are responsible for the performance of the required maintenance
listed in your owner’s manual. Maruyama Manufacturing Company, Inc. recommends that you retain all
receipts covering maintenance on your small off-road engine, but Maruyama Manufacturing Company,
Inc. cannot deny warranty coverage solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
As the small off-road engine owner, you should however be aware that Maruyama Manufacturing
Company, Inc. may deny you warranty coverage if your small off-road engine or a part has failed due to
abuse, neglect, or improper maintenance or unapproved modifications.
• You are responsible for presenting your small off-road engine to a Maruyama Manufacturing Company,
Inc. distribution center or service center as soon as the problem exists. The warranty repairs shall be
completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact Maruyama
Manufacturing Company, Inc. at 1-866-783-7400, or warranty@maruyama-us.com.
The evaporative emission warranty parts list shall include all parts whose failure would increase
evaporative emissions, and may contain, but is not limited to, the following parts:
(1) Fuel Tank
(2) Fuel Cap
(3) Fuel Lines (for liquid fuel and fuel vapors)
(4) Fuel Line Fittings
(5) Pressure Relief Valves
(6) Control Valves
(7) Vacuum Control Diaphragms
(8) Purge Valves
(9) Carburetor Purge Port Connector
The exhaust emission warranty parts list shall include all parts whose failure would increase exhaust
emissions, and may contain, but is not limited to, the following parts:
(1) Fuel Metering System
(A) Carburetor and internal parts
(2) Cold start enrichment system
(3) Controlled hot air intake system
(4) Air filter
(5) Ignition System
(6) Spark Plug
(7) Magneto or electronic ignition system
(8) Spark advance/retard system
(9) Exhaust Gas Recirculation (EGR) System
(10) EGR valve body, and carburetor spacer if applicable
(11) Air pump or pulse valve
— US-6 —
Contents
Page US-
Limited Warranty Statement ...................................... 1
FEDERAL EMISSION CONTROL ........................... 3
CALIFORNIA EMISSION CONTROL .................... 4
Contents ...................................................................... 6
Introduction................................................................. 6
Safety ......................................................................... 7
Operator Safety ........................................................... 7
Trimmer/Brushcutter Safety
.................................... 7
Fuel Safety ............................................................. 7
Trimmer/Brushcutter Operating Safety ................ 8
Safety and Instruction Decals ................................ 9
Product Description ..................................................... 9
Assembly.................................................................... 10
Loop Handle Installation ...................................... 10
Handlebar Installation .......................................... 10
Installing Debris Shield ........................................ 10
Installing Cutting Attachment ............................. 12
Attaching Shoulder Harness/ Strap ..................... 14
Before Operation ...................................................... 14
Oil and Fuel ........................................................ 14
Mixing Gasoline And Oil ................................... 15
Starting And Stopping
........................................ 16
Operation .................................................................. 17
Trimmer/Brushcutter Operating Position ........... 17
Cutting with Trimmer Head ................................ 19
Cutting Direction ................................................. 19
Cutting Blades ..................................................... 20
Maintenance .............................................................. 20
Idle Speed Adjustment ......................................... 20
Air Filter .............................................................. 21
Fuel Filter ............................................................ 21
Spark Plug ............................................................ 21
Cylinder Cooling Fins ......................................... 22
Spark Arrester ..................................................... 22
Exhaust Muffler .................................................. 23
Gearcase .............................................................. 24
General Cleaning and Tightening ....................... 24
Blade Sharpening ............................................... 24
Storage ...................................................................... 25
Troubleshooting ........................................................ 26
Maintenance Period ................................................. 26
Specifications ............................................................ 26
Introduction
Thank you for purchasing a MARUYAMA product.
MARUYAMA, it’s distributors, and dealers want you to
be completely satisfied with your new product. Please
feel free to contact your local Authorized Service Dealer
for help with service, genuine MARUYAMA parts, or
other information you may require.
Whenever you contact your Authorized Service Dealer
or the factory, always know the serial number of your
product. This number will help the Service Dealer or
Service Representative provide exact information about
your specific product. You will find the model and
serial number located in a unique place on the product
(Product Description on page US-9).
For your convenience, write the product model name
and serial number in the space to the below.
Read this manual carefully to learn how to operate and
maintain your product correctly. Reading this manual
will help you and others avoid personal injury and
damage to the product.
Although MARUYAMA designs, produces and mar-
kets safe, state-of-the-art products, you are responsible
for using the product properly and safely. You are also
responsible for training persons who you allow to use
the product about safe operation.
The MARUYAMA warning system in this manual
identifies potential hazards and has special safety mes
-
sages that help you and others avoid personal injury,
even death. DANGER, WARNING and CAUTION are
signal words used to identify the level of hazard.
However, regardless of the hazard, be extremely careful.
DANGER signals an extreme hazard that will cause
serious injury or death if the recommended precautions
are not followed.
WAR NING signals a hazard that may cause serious
injury or death if the recommended precautions are not
followed.
CAUTION signals a hazard that may cause minor or
moderate injury if the recommended precautions are
not followed. Two other words are also used to high-
light information. “Important” calls attention to special
mechanical information and “Note” emphasizes gener-
al information worthy of special attention.
Model Name
_______________
Serial No.
________________
— US-7 —
Safety
Operator Safety
1. Read and understand this Owner’s/ Operator’s
Manual before using this product. Be thoroughly
familiar with the proper use of this product.
2. Never allow children to operate the Trimmer/
Brushcutter. It is not a toy. Never allow adults to
operate the unit without first reading the
Owner’s/ Operator’s Manual.
3.
Always wear eye protection that complies with ANSI
(American National Standards Institute) Z87-1.
4. Always wear hearing protection.
5. Always wear heavy, long pants, a long sleeved
shirt, boots and gloves. Do not wear loose cloth-
ing, jewelry, short pants, sandals, or go barefoot.
Secure hair so it is above shoulder length.
6. Never operate this Trimmer/Brushcutter when
you are tired, ill, or under the influence of alcohol,
drugs or medication.
7.
Never start or run the engine inside a closed room or
building. Breathing exhaust fumes can cause death.
8. Keep handles clean of oil, fuel and dirt.
Trimmer/Brushcutter Safety
1. Make sure the Trimmer/Brushcutter is assembled
correctly and that the Cutting attachment is cor-
rectly installed and securely fastened as instructed
in the Assembly section.
2. Inspect the Trimmer/Brushcutter before each use.
Replace damaged parts. Check for fuel leaks.
Make sure all fasteners are in place and tightened
securely. Follow the maintenance instructions
beginning on page US-20.
3. Make sure the cutting head does not rotate at
engine idle speed. Refer to Idle Speed Adjustment,
page US-20.
4. Inspect the cutting head and replace any parts that
are cracked, chipped or damaged before using the
Trimmer/Brushcutter.
5. Make sure the debris shield is installed and posi-
tioned correctly before using the Trimmer/
Brushcutter.
6. Never use a cutting head or replacement parts that
are not approved by MARUYAMA.
7.
Maintain the Trimmer/Brushcutter according to the
recommended maintenance intervals and pro-
cedures in the Maintenance section on page US- 20.
8. Shut off the engine and be certain the cutting head
has completely stopped rotating before inverting
the Trimmer/Brushcutter, performing maintenance
on or working on the machine.
9.
If running problems or excessive vibration occur,
stop immediately and inspect the unit for the
cause. If the cause cannot be determined or is
beyond your ability to correct, return the Trimmer/
Brushcutter to your servicing dealer for repair.
Fuel Safety
1. Gasoline is highly flammable and must be handled
and stored carefully. Use a container approved for
fuel to store gasoline and/ or fuel/oil mixture.
2. Mix and pour fuel outdoors, where there are no
sparks or flames.
3. Do not smoke near fuel or Trimmer/Brushcutter,
or while using the Trimmer/Brushcutter.
4. Do not overfill the fuel tank. Stop filling 1/4-1/2
in. (6mm-13mm) from the top of the tank.
5.
Wipe up any spilled fuel before starting the engine.
6. Move the Trimmer/Brushcutter at least 10ft. (3m)
away from the fueling location before starting the
engine.
10 ft. (3 m) minimum
— US-8 —
7. Do not remove the fuel tank cap while the engine
is running, or right after stopping the engine.
8. Allow the engine to cool before refueling.
9. Drain the tank and run the engine dry before stor-
ing the unit.
10. Store fuel and Trimmer/Brushcutter away from
open flame, sparks and excessive heat. Make sure
fuel vapors cannot reach sparks or open flames
from water heaters, furnaces, electric motors, etc.
Trimmer/ Brushcutter Operating
Safety
1. THIS TRIMMER BRUSHCUTTER CAN
CAUSE SERIOUS INJURIES. Read the instruc-
tions carefully. Be familiar with all controls and
the proper use of the Trimmer/Brushcutter.
2. Make sure the Ø3.5 or Ø6 mm pin has been
removed from the gearcase and boss adapter
before you start the engine.
3. Avoid using the Brushcutter near rocks, gravel,
stones and similar material which can become
dangerous projectiles.
4. Inspect your work area before you begin. Remove
objects such as broken glass, nails, wire and rocks
which can become dangerous projectiles if thrown
by the Trimmer/Brushcutter. Remove string, rope
or similar materials which can become entangled
in the cutting head.
5. Keep children, bystanders and animals outside a
50ft. (15m) radius from the operator and Trimmer/
Brushcutter.
6. If you are approached while operating the
Trimmer/Brushcutter, stop the engine and cutting
head rotation.
7. Never allow children to operate the Trimmer/
Brushcutter.
8. Use the Trimmer/Brushcutter only in daylight or
good artificial light.
9. Never operate the Trimmer/Brushcutter without
proper guards or other protective safety devices in
place.
10. Always keep the Trimmer/Brushcutter on the
right side of your body.
11. Do not raise the cutting head above waist level.
12. Do not put hands or feet near or under any rotat-
ing parts. Keep clear at all times. Keep all parts of
your body away from the rotating cutting attach-
ment and hot surfaces such as the muffler.
13. When cutting heavy brush or small trees, always
move the Brushcutter from right to left to prevent
kick-back .
14. Keep firm footing and balance. Do not overreach.
15. Use the right tool for the job. Do not use the
Trimmer/Brushcutter for any job that is not rec-
ommended by MARUYAMA.
CORRECT
No Kick-back Zone
Direction of Motion
INCORRECT
Direction of Motion
DANGER – Kick-back Zone
50 ft. (15 m) Minimum
— US-9 —
Safety and Instruction Decals
Safety decals and instructions are easily visible to the operator and are located near any area of
potential danger. Replace any decal that is damaged or lost.
ON SHAFT
(Part No.221501)
ON SHAFT
(Part No.221502)
9
B42L, B42, B42A
Product Description
1
2
3
5
18
7
8
9
13
10
12
16
17
4
11
1
2
3
5
6
7
8
9
19
10
14
15
12
16
17
4
11
1
2
3
5
6
7
8
9
19
10
14
15
12
16
17
4
11
B42L
B42
B42A
6
1. Gearcase
2. Shaft Assembly
3. Model Name
4. Safety Decal
5. Attachment Ring for Shoulder
Harness
6. Throttle Trigger and Stop Switch
7. Clutch Drum Housing
8. Engine
9. Serial Number (on rear of engine)
10. Air Filter
11. Fue l Tan k
12. Throttle Cable and Stop Switch Wires
13. Shoulder Strap
14. Handle Grip
15. Handlebar
16. Debris Shield
17. Brushcut ter Blade
18. Loop Handle
19. Shoulder Harness
— US-10 —
Assembly
Loop Handle Installation
1. Place the loop handle and the bottom clamp
approximately 11 inches (28cm) from the end of
the stop switch/ throttle trigger assembly for an
initial handle position.
2. Install the four screws and nuts. Leave the screws
finger-tight.
3. Reposition the loop handle up or down the shaft
assembly to the most comfortable position, but no
closer than 9 inches (22.8cm) from the end of the
stop switch.
4. Tighten the screws and nuts.
Handlebar Installation
IMPORTANT: Be careful not to damage the throt-
tle cable and stop switch wires when you remove
the handlebars from the shipping carton.
1.
Loosen the four screws on the top of the clamp bracket.
2. Insert the left and right handlebars into the clamp
bracket. Note that the handlebar with the throttle
trigger and stop switch goes on the right-hand side
of the Trimmer/Brushcutter.
3. Adjust the handlebar to the desired position, then
tighten the four screws.
4. Clamp the throttle cable and the stop switch wires
as shown.
Installing Debris Shield
[B42L, B42]
WARNING
POTENTIAL HAZARD
• Foreign objects can be thrown by the
Trimmer/Brushcutter.
WHAT CAN HAPPEN
• Contact with thrown objects can cause
personal injury.
HOW TO AVOID THE HAZARD
• Never operate the Trimmer/Brushcutter
without the debris shield in place.
Loop Handle
Screw (4)
Nut (4)
Bottom Clamp
Shaft Assembly
Throttle Trigger and Stop Switch
Stop Switch Wires and
Throttle Cable
Clamp Bracket
Screw (4)
Handlebar
— US-11 —
Debris Shield
Attach the debris shield to the gearcase with the two
M6 x 30 screws as shown on Fig. 1.
Shield Extension
(Install the string cutoff blade and shield extension to
the debris shield.)
1. Insert the square nut into shield extension as
shown on Fig. 2.
2. Attach the string cutoff blade to shield extension
using M5 x 20 screw, locking with square nut (on
Fig.2) as shown on Fig. 3 .
3. Enter the guide in the slot of debris shield on Fig.4.
Make sure place the three hooks into the position
on the shield as shown on Fig.5.
[B42A]
Debris Shield
Attach the debris shield to the gearcase with the four
M5 x 10 screws.
WARNING
POTENTIAL HAZARD
• Foreign objects can be thrown by the
Trimmer/ Brushcutter.
WHAT CAN HAPPEN
• Contact with thrown objects can cause
personal injury.
HOW TO AVOID THE HAZARD
• Never operate the Trimmer/ Brushcutter
without the debris shield in place.
Gearcase
M5 x 10 Screw (4)
Debris Shield
CAUTION
POTENTIAL HAZARD
• The cutoff blade is sharp.
WHAT CAN HAPPEN
• Contact with cutoff blade could cause
serious cuts or personal injury.
HOW TO AVOID THE HAZARD
• Keep hands, feet and clothing away from
cutoff blade.
Shield Extension
Square Nut Fig.2
M5 x 20 Screw
String Cut off Blade
Fig.3
M6 x 30 Screw (2)
Gearcase
Debris Shield
Fig.1
Fig.4 Fig.5
Debris Shield
Guide
Hook
Hook
Shield Extension
— US-12 —
Installing Cutting Attachment
Trimmer Head
[B42L, B42]
IMPORTANT: Make sure the trimmer head is
for LEFT-HAND ROTATION (counter-clock-
wise) as viewed from the operator’s position,
and that the trimmer head adapter is a female,
M10 left-hand thread.
1. Remove the blade nut and stabilizer from the
attaching shaft out of the gearcase. (keep the
blade nut and stabilizer)
NOTE: The blade nut has left-hand thread.
2. Align the hole in the boss adapter with the hole in
the gearcase.
3. Insert the Ø6 mm pin into the hole in the boss
adapter and the hole in the gearcase to lock the
attaching shaft.
4. Thread the trimmer head adapter into the attach-
ing shaft, then tighten the trimmer head by hand.
NOTE: The trimmer head adapter has left-
hand thread.
5. Remove the Ø6 mm pin from the boss adapter and
gearcase.
[B42A]
IMPORTANT: Make sure the trimmer head is
for LEFT-HAND ROTATION (counter-clock-
wise) as viewed from the operator’s position,
and that the trimmer head adapter is a male,
M8 left-hand thread.
1. Remove the blade bolt and the stabilizer from the
attaching shaft out of the gearcase. (keep the
blade bolt and stabilizer)
NOTE: The blade bolt has left-hand thread.
2. Align the hole in the boss adapter with the guide
slot in the gearcase.
3. Insert the Ø3.5 mm pin into the hole in the boss
adapter and the guide slot in the gearcase to lock
the attaching shaft.
4. Thread the trimmer head adapter into the attach-
ing shaft, then tighten the trimmer head by hand.
NOTE: The trimmer head adapter has left-
hand thread.
5. Remove the Ø3.5 mm pin from the boss adapter
and gearcase.
Gearcase
Ø6mm Pin
Left-hand thread
Boss Adapter
Trimmer Head Adapter
Trimmer Head
Attaching Shaft
Gearcase
Left-hand thread
Boss Adapter
Trimmer Head Adapter
Trimmer Head
Attaching Shaft
WARNING
POTENTIAL HAZARD
If the trimmer head is not adequately
tightened, it can come loose from the
Trimmer/Brushcutter during use.
WHAT CAN HAPPEN
This may cause damage to property or
personal injury.
HOW TO AVOID THE HAZARD
Make sure the trimmer head is secure-
ly fastened to the attaching shaft in the
gearcase.
Ø3.5mm Pin
Clamping Washer
Clamping Washer
— US-13 —
Brushcutter Blade
[B42L, B42]
1. Remove the blade nut, stabilizer and clamping
washer from the attaching shaft out of the
gearcase.
NOTE: The blade nut has left-hand threads.
2. Install the brushcutter blade onto the boss adapter,
then reinstall the clamping washer, stabilizer and
blade nut.
3. Align the hole in the boss adapter with the guide
hole in the gearcase.
4. Insert the Ø6 mm pin into the hole in the boss
adapter and the hole in the gearcase to lock the
attaching shaft.
5. Tighten the blade nut.
6. Remove the Ø6 mm pin from the boss adapter and
gearcase.
[B42A]
1. Remove the blade bolt, stabilizer and clamping
washer from the attaching shaft out of the
gearcase.
NOTE: The blade bolt has left-hand threads.
2. Install the brushcutter blade onto the boss adapter,
then reinstall the clamping washer, stabilizer and
blade bolt.
3. Align the hole in the boss adapter with the guide
slot in the gearcase.
4. Insert the Ø3.5 mm pin into the hole in the boss
adapter and the guide slot in the gearcase to lock
the attaching shaft.
5. Tighten the blade bolt.
6. Remove the Ø3.5 mm pin from the boss adapter
and gearcase.
Gearcase
Blade Nut
Stabilizer
Brushcutter Blade
Ø6mm Pin
Left-hand thread
Boss Adapter
Attaching Shaft
Gearcase
Blade Bolt
Stabilizer
Brushcutter Blade
Ø3,5mm Pin
Left-hand thread
WARNING
POTENTIAL HAZARD
If the Brushcutter blade is not adequate
-
ly tightened, it can come loose from the
Brushcutter during use.
WHAT CAN HAPPEN
This may cause damage to property or
personal injury.
HOW TO AVOID THE HAZARD
Make sure the Brushcutter blade is
securely fastened to the attaching shaft
in the gearcase.
CAUTION
POTENTIAL HAZARD
Brushcutter blade is sharp.
WHAT CAN HAPPEN
• Contact with sharp blade can cause seri
-
ous personal injury.
HOW TO AVOID THE HAZARD
Wear gloves when you handle the blade.
Clamping Washer
Clamping Washer
Boss Adapter
Attaching Shaft
— US-14 —
Attaching Shoulder Harness/Strap
[B42, B42A]
Snap the Hook into the ring on the shaft assembly. To
detach the Harness quickly from the Trimmer/
Brushcutter, push the red button.
[B42L]
Snap the strap hook into the ring on the shaft assembly.
To detach the strap quickly from the Brushcutter, pull
upward on the red band.
Before Operation
Oil and Fuel
1. Do not smoke near fuel.
2. Mix and pour fuel outdoors and where there are
no sparks or flames.
3. Always shut off the engine before refueling.
Never remove the fuel tank cap while the engine
is running or just right after stopping the engine.
4. Always open the fuel tank cap slowly to release
any possible overpressure inside the tank.
WARNING
POTENTIAL HAZARD
Without the Shoulder Harness/Strap
Installed on the Trimmer/Brushcutter,
the blade can produce side thrust which
can expose the operator and bystanders
to blade contact.
WHAT CAN HAPPEN
• Contact with the Brushcutter blade can
cause serious personal injury.
HOW TO AVOID THE HAZARD
Never operate the Trimmer/Brushcutter
without installing and using the
Shoulder Harness/Strap.
POTENTIAL HAZARD
In certain conditions gasoline is extremely
flammable and highly explosive.
WHAT CAN HAPPEN
A fire or explosion from gasoline can
burn you, others, and cause property
damage.
HOW TO AVOID THE HAZARD
Use a funnel and fill the fuel tank out-
doors, in an open area, when the engine
is cold. Wipe up any gasoline that spills.
Do not fill the fuel tank completely full.
Add gasoline to the fuel tank until the
level is 1/4 to 1/2 in. (6 mm to 13 mm) below
the bottom of the filler neck. This empty
space in the tank allows gasoline
to
expand.
Never smoke when handling gasoline,
and stay away from an open flame or
where gasoline fumes may be ignited by
a spark.
Store gasoline in an approved container
and keep it out of the reach of children.
Never buy more than a 30-day supply of
gasoline.
DANGER
WARNING
POTENTIAL HAZARD
Gasoline contains gasses that can build
up pressure inside a gas tank.
WHAT CAN HAPPEN
Fuel can be sprayed on you when remov
-
ing gas cap.
HOW TO AVOID THE HAZARD
• Remove fuel cap slowly to avoid injury
from fuel spray.
Red Band
Strap
Ring
Hook
Pull
Red Button
PRESS
Push
— US-15 —
5. Do not overfill the fuel tank. Stop filling 1/4-1/2
in. (6 mm-13 mm) from the top of the tank.
6. Tighten the fuel tank cap carefully but firmly after
refilling.
7. Wipe up any spilled fuel before starting the
engine.
8. Move the Trimmer/Brushcutter at least 10 ft. (3m)
away from the fueling location and fuel storage
container before starting the engine.
Recommended Oil Type
Only use a two-stroke engine oil formulated for use in
high-performance, air-cooled two-stroke engines.
MARUYAMA brand two-stroke oil is formulated for
use in high-performance, air-cooled two-stroke engines.
IMPORTANT: Do not use National Marine
Manufacturer’s Association (NMMA) or BIA
certified oils. This type of two-stroke engine oil
does not have the proper additives for air-
cooled, two-stroke engines and can cause
engine damage.
Do not use automotive motor oil. This type of
oil does not have the proper additives for air-
cooled, two-stroke engines and can cause
engine damage.
Recommended Fuel Type
Use clean, fresh lead-free gasoline, including oxygenat-
ed or reformulated gasoline, with an octane rating of 89
or higher. To ensure freshness, purchase only the quan-
tity of gasoline that can be used in 30 days. Use of
lead-free gasoline results in fewer combustion chamber
deposits and longer spark plug life. Use of premium
grade fuel is not necessary or recommended.
Use of Fuel Additives
IMPORTANT: NEVER USE ALCOHOL,
GASOHOL CONTAINING MORE THAN
10% ALCOHOL BECAUSE ENGINE FUEL
SYSTEM DAMAGE COULD RESULT.
DO NOT USE FUEL ADDITIVES OTHER
THAN THOSE MANUFACTURED FOR
FUEL STABILIZATION DURING STORAGE
SUCH AS MARUYAMA’S STABILIZER/
CONDITIONER OR A SIMILAR PRODUCT.
MARUYAMAS STABILIZER/ CONDITION-
ER IS A PETROLEUM DISTILLATE BASED
CONDITIONER/ STABILIZER.
MARUYAMA DOES NOT RECOMMEND
STABILIZERS WITH AN ALCOHOL BASE
SUCH AS ETHANOL, METHANOL OR ISO-
PROPYL. ADDITIVES SHOULD NOT BE
USED TO TRY TO ENHANCE THE POWER
OR PERFORMANCE OF MACHINE.
Mixing Gasoline And Oil
IMPORTANT: The engine used on this
Trimmer/Brushcutter is of a two-stroke design.
The internal moving parts of the engine, i.e.,
crankshaft bearings, piston pin bearings and
piston to cylinder wall contact surfaces, require
oil mixed with the gasoline for lubrication.
Failure to add oil to the gasoline or failure to
mix oil with the gasoline at the appropriate
ratio will cause major engine damage which
will void your warranty.
For your fuel premix, use MARUYAMA
Premium two-stroke Oil Mix, or equivalent
ISO-L-EGD & JASO FD oil with a minimum
89 octane high quality gasoline. MARUYAMA
two-stroke oil is specially formulated to meet
the requirements of high-performance,
low-emission air-cooled two-stroke engines. Use
of other oils may lead to service issues which
may not be covered by your warranty.
Fuel Mixture
The fuel: oil ratio is 50 parts gasoline to 1 part oil or
50:1.
10 ft. (3 m) minimum
50:1
— US-16 —
NOTE: Never use a mixing ratio less than 50:1
regardless of the oil package mixing instruc-
tions. Ratios less than 50:1, (for example, 60:1,
80:1, 100:1), reduce the amount of lubrication to
the internal moving parts of the engine and can
cause damage.
Fuel Mixture Chart
Gasoline 50:1 two-stroke oil
1 gallon 2.6 oz
.
2 gallons 5.1 oz.
5 gallons 12.8 oz.
1 liter 20 mL
5 liters 100 mL
Mixing Instructions
IMPORTANT: Never mix gasoline and oil
directly in the Trimmer/Brushcutter fuel tank.
1. Always mix fuel and oil in a clean container
approved for gasoline.
2. Mark the container to identify it as fuel mix for
the Trimmer/Brushcutter.
3. Use regular unleaded gasoline and fill the contain-
er with half the required amount of gasoline.
4. Pour the correct amount of oil into the container
then add the remaining amount of gasoline.
5. Close the container tightly and shake it momen-
tarily to evenly mix the oil and the gasoline before
filling the fuel tank on the Trimmer/Brushcutter.
6. When refilling the Trimmer/Brushcutter fuel tank,
clean around the fuel tank cap to prevent dirt and
debris from entering the tank during cap removal.
7. Always shake the premix fuel container momen-
tarily before filling the fuel tank.
8. Always use a spout or funnel when fueling to
reduce fuel spillage.
9. Fill the tank only to within 1/4-1/2 in. (6 mm-13
mm) from the top of the tank. Avoid filling to the
top of the tank filler neck.
Starting And Stopping
Before Starting The Engine
1. Fill the fuel tank as instructed in the Before
Operation section of this manual (US-14).
2. Rest the Trimmer/Brushcutter on the ground.
3. Make sure the cutting attachment is clear of any
broken glass, nails, wire, rocks or other debris.
4. Keep all bystanders, children and animals away
from the working area.
Cold Starting Procedure
This Trimmer/Brushcutter is equipped with a fuel
primer and a choke system. To start a “cold” engine
properly, perform the following procedure:
1. Pump the primer bulb until fuel can be seen flow-
ing through the fuel return line to the fuel tank.
(Flowing fuel should be almost clear, not foamy or
full of bubbles.)
2. Move the choke lever to the closed (
) position
and move the stop switch to the “START” (ON)
position.
Primer Bulb
Fuel Return Line
Starter Grip
Choke Lever
Idle Position
Fast-idle Start Lock
Stop Switch
START (ON)
STOP (OFF)
Fast-idle Start
Position
— US-17 —
3. Lock the throttle trigger in the fast-idle start posi-
tion, then pull the starter grip.
4. After the engine starts, squeeze and release the
throttle trigger to return it to the idle position, then
move the choke lever to the open (
) position.
If the engine stops running before you move the
choke lever to the open (
) position:
Go ahead and open the choke, pull the starter grip with
the throttle trigger positioned at Fast-idle position.
Hot Restart
To start an engine that is already warmed up (hot restart),
or if the ambient temperature exceeds 68°F (20°C):
1. Pump the primer bulb until fuel can be seen flow-
ing through the fuel return line to the fuel tank.
(Flowing fuel should be almost clear, not foamy
or full of bubbles.)
2. Move the choke lever to the open (
) position
and move the stop switch to the “START” (ON)
position.
3. Leave the throttle trigger in the idle position and
pull the starter grip.
4. If the engine fails to start after three to four pulls,
follow the instruction in the Cold Starting
Procedure section (US-16).
If the engine fails to start after you follow the
above procedures, contact an authorized
MARUYAMA dealer.
To Stop The Engine:
1. Release the throttle trigger.
2. Slide the stop switch to the “STOP” (OFF)
position.
Operation
Trimmer/Brushcutter Operating
Position
Before using the Trimmer/Brushcutter, check the
following::
1. Make sure the Holding Tool (Ø3.5 or Ø6mm Pin)
has been removed from the gearcase and boss
adapter before you start the engine.
2. The operator must be wearing the harness
attached to the Trimmer/Brushcutter, and the
Trimmer/Brushcutter must be on the operator’s
right side.
3. The operator’s right hand should be holding the
right-hand throttle grip, with his or her fingers on
the throttle trigger.
CAUTION
Read the Safety instructions on US-7
concerning proper use of the Trimmer/
Brushcutter.
WARNING
POTENTIAL HAZARD
Foreign objects can be thrown by
Trimmer/Brushcutter.
WHAT CAN HAPPEN
Contact with thrown objects can cause
personal injury.
HOW TO AVOID THE HAZARD
Never operate the Trimmer/Brushcutter
without the debris shield in place.
Idle Position
Fast-idle Start Lock
Stop Switch
Fast-idle Start
Position
START (ON)
STOP (OFF)
POTENTIAL HAZARD
The components of your recoilstarter
assembly are under high spring tension.
If improperly disassembled these parts
maystrike you with considerable force,
possibly causing personal injury.
WHAT CAN HAPPEN
Contact with the parts can cause severe
personal injury.
HOW TO AVOID THE HAZARD
Never attempt to disassemble your recoil
starter assembly yourself. Always consult
your authorized MARUYAMA dealer for
repair by qualified service technicians.
WARNING
CAUTION
Do not pull the Starter rope all the way out.
— US-18 —
4. The left hand should be holding the left-hand grip
with the fingers and thumb fully enclosed around
the grip.
5. Accelerate and hold the engine at cutting speed
before entering the material to be cut.
6. Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
7. Stop the Trimmer/ Brushcutter engine when
moving between work sites.
• If the Cutting attachment blade becomes jammed,
stop the engine immediately.
• Make certain all moving parts have stopped and
disconnect the spark plug before inspecting the
equipment for damage.
• Never use a Trimmer/Brushcutter that has chipped,
cracked or broken cutting attachment or shield.
[B42, B42A]
IMPORTANT: To detach the harness quickly
from the Trimmer/Brushcutter, push the red
button.
[B42L]
IMPORTANT: To detach the strap quickly from
the Trimmer/Brushcutter, pull upward on the
red band.
WARNING
Red Band
Strap
Ring
Hook
Pull
POTENTIAL HAZARD
Without the shoulder harness/strap
installed, the Brushcutter blade can pro
-
duce side thrust which can expose the
operator and bystanders to blade contact.
If the Brushcutter is not correctly posi-
tioned on the operators right side, the
blade can produce side thrust which can
expose the operator and bystanders to
blade contact.
WHAT CAN HAPPEN
Contact with the Brushcutter blade can
cause severe personal injury.
HOW TO AVOID THE HAZARD
Never operate the Brushcutter without
installing and using the shoulder har
-
ness/ strap.
Always operate the Brushcutter with the
unit on your right side.
CAUTION
Always wear gloves and protective cloth-
ing when operating the Trimmer/
Brushcutter.
Eye Protection
Hand holding - Left hand
Grip, and fingers and
thumb fully enclosed
around the grip
Cutting Attachment Near
and Parallel to Ground
Hearing Protection
Hand Holding Throttle
Grip, Fingers on
Throttle Trigger
Red Button
PRESS
Push
— US-19 —
Cutting with Trimmer Head
The tip of the line does the cutting. The line
should stay extended while cutting.
Do not force the line into the material. Forcing the
line will cause it to slap against the material, increas
-
ing line usage and causing poor cutting results.
Trimming
Hold the bottom of the trimmer head about 3 in. (7.6
cm) above the ground and at an angle. Allow only the
tip of the line to make contact.
Scaling
To remove unwanted vegetation, hold the trimmer head
about 3 in. (7.6 cm) above the ground and at an angle.
Allow the tip of the line to strike the ground cutting the
vegetation off at the surface.
Mowing
Keep the line parallel to the ground and use a gentle
side-to-side motion.
Cutting Direction
When cutting heavy brush or small trees, always move
the Brushcutter from right to left. Moving the Brushcutter
from left to right can cause the blade to kick back.
WARNING
POTENTIAL HAZARD
Cutting heavy brush or small trees from
the wrong direction can cause the
Brushcutter blade to kick back.
WHAT CAN HAPPEN
Contact move the Brushcutter blade can
cause severe personal injury.
HOW TO AVOID THE HAZARD
• Always move the Brushcutter from right
to left when cutting heavy brush or small
trees as shown.
Three inches
(7.6 cm) Above
Ground
CORRECT
INCORRECT
Three inches
(7.6c m)
Above Ground
Three inches
(7.6c m)
Above Ground
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Maruyama B42 Le manuel du propriétaire

Catégorie
Coupe-herbe
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues