Hobart ML-134335 Mode d'emploi

HL800

HL1400

ML-134319

ML-134335

Page 1 - English

Page 43 - French

Page 90 - German

INSTALLATION AND OPERATION MANUAL

MANUEL D’INSTALLATION ET D’UTILISATION

INSTALLATIONS UND BEDIENUNGSANLEITUNG

F-34947 Rev A (Sept 2006)

1

nglish / Contents

Section Page

2

E

Safety Information 1.0 4

Safety Guidelines 1.1 4

Warning Symbols 1.2 4

Liability 1.3 5

Foreword 2.0 5

General Information 3.0 5

Caring for our Environment 4.0 5

Packaging Material 4.1 5

Disposal of your old appliance 4.2 5

Safety Instructions 5.0 6

Dust Hazard 5.1 6

Never 5.2 6

Always 5.3 7

Using the Mixer 6.0 7

Operating for the First Time 6.1 7

Mixer Component Identification Fig. 1 8

Standard Timer Controls 6.2 9

Recipe Timer Controls 6.2 10

Bowl Placement 6.3 10

Agitator 6.4 11

Hold to run operation 6.5 11

Power bowl lift 6.6 12

Prepare for Mixing 6.7 12

Operating Notes 6.8 13

Timer Operation 6.9 13

Recipe Mode – To enter and Exit 6.9 15

Reviewing Recipe Steps 6.9 15

Running a Recipe 6.9 16

Interrupting a Recipe 6.9 16

Entering a Special Function 6.9 17

Enter The Access Code 6.9 17

Programming a Recipe [Set…rECP] 6.9 18

Programming a Pause 6.9 18

Making a Recipe Active or Inactive [Atth…rECP] 6.9 19

Setting the Access Code [Set…CodE] 6.9 19

3

Unloading 6.10 20

Wire Guard Cage 6.11 20

Remove and Cleaning the Wire Guard Cage 6.12 21

Re-Fitting the Wire Guard Cage 6.13 22

Mixing capacity 7.0 22

Mixing Capacity Chart – HL800 7.1 25

Mixing Capacity Chart – HL1400 7.2 26

Mixer Agitators 8.0 28

Splash Cover and bowl extension ring 8.2 29

Bowl Scraper Attachment 8.3 29

Bowl truck 8.4 30

Cleaning 9.0 31

Cleaning after Use 9.1 32

Installation and commissioning 10.0 31

Overall Dimensions (HL800) Fig. 8 31

Overall Dimensions (HL1400) Fig. 9 32

Technical Information Table 1 33

Unpacking and Handling 10.1 33

Location 10.2 34

Electrical Installation 10.3 35

Electrical Connection 10.4 35

Operator Training 10.5 35

Mixer Maintenance 11.0 35

Lubrication 11.1 36

Slideways 11.1.1 36

Bowl Locking Mechanism 11.1.2 36

Planetary seal 11.1.3 36

Transmission oil 11.1.4 36

Adjustments 11.2 37

Agitator Clearance 11.2.1 37

To Measure the Agitator Clearance 11.2.2 37

Interlock Safety System 11.3 38

Transmission belt 11.4 38

Fault Finding 12.0 38

Recommended Spares 13.0 39

Notes 14.0 41

Service Contact Numbers 15.0 42

4

.0 SAFETY INFORMATION.1

he p cedures and precautions contained inT ro this manual are understood to apply to the machinery

prepared to assist the operator to understand, maintain,

1.1 SAFETY GUIDELINES.

only when it is used in the prescribed manner. If the machinery is used other than in the

recommended manner, the operator will be responsible for his/her own safety and for the safety of

the other persons who may be involved.

he information in this manual has beenT

and operate the mixer. In order to prevent accidents, read, understand and follow all the precautions

and warnings contained in this manual before installation or operating for the first time. This manual

must be studied to obtain a clear understanding of the mixer and its capabilities.

nsur sufficient precautions are observeE e d during manual handling of the mixer particularly when

this appliance. It is vital to adhere to the cleaning instructions

any fittings whilst the machine is operating.

e mixer.

chinery and electricity are potentially hazardous and may cause injury if sufficient

ding on frequency of use.

may be harmful to health causing rhinitis (running noses),

.2

WARNING SYMBOLS.

moving into position on installation. Reference must be made to manual handling regulations. The

mixer weights are given in Table 1.

Do not hose or pressure clean •

detailed in Section 9 of this manual.

Do not remove any covers or loosen •

Ensure this manual is kept in an easily accessible place for future reference near th•

All operators must be trained in the safe operation of the mixer and attachments. •

Ensure that the electrical supply has been isolated before attempting to service or move the •

mixer.

Rotating ma•

precautions are not taken prior to operating or servicing the machine.

Always have your mixer regularly serviced; at least twice a year, depen•

When mixing products that develop dust care must be taken. Mix the ingredients using the STIR •

facility until the dust is eliminated.

Exposure to dust (including flour)•

watering eyes and possibly occupational asthma.

1

o ide tify the safety messages in this maT n nual, the following symbols have been used

is important

sed when there are risks of an electrical nature. Prior to

arily where the corresponding informationThe "Warning" symbol is found prim

for the safe use of the machinery.

he electrical hazard symbol is uT

servicing the machinery, always disconnect the power cable from the mains supply.

5

1.3 LIABILITY.

Installations and repairs which are not carried out by Authorised technicians or the use of other

than original spare parts, and any technical alterations to the machine, may affect the warranty

set out in the standard conditions of sale.

2.0 FOREWORD.

Hobart reserves the right to alter the design of their products without prior notice. Whilst every effort

is made to ensure this publication reflects the latest design, the Company cannot guarantee full

compliance.

Take pride in your HL800/HL1400 Mixer - keep it clean and in good mechanical and electrical

condition.

3.0 GENERAL INFORMATION.

The information and instructions contained in this manual may not cover all details or variations in

the equipment, nor provide for every eventuality to arise with installation, operation, or maintenance.

If additional information is required, please contact your local Hobart office.

The HL800/HL1400 Mixers are designed to mix food products as detailed on the specification chart

(Sections 7.1 and 7.2, pages 25 and 26).

The Legacy™ 80-litre mixer is a heavy duty mixer which features a 3-horsepower motor,

SmartTimer™ and power bowl lift as standard equipment.

The Legacy

TM

140-quart mixer is a heavy-duty mixer which features a 5-horsepower motor, digital

SmartTimer

TM

and power bowl lift as standard equipment.

A programmable Recipe Timer is optional.

Both models have four mix speeds and stir speed.

The machine is rated to operate on the electrical supplies shown in Table 1, page 33.

The bowl support and the guard are interlocked so that when either is not in their correct operating

positions, the mixer will not work.

4.0

CARING FOR OUR ENVIRONMENT.

4.1

PACKAGING MATERIAL.

The pallet and protective packing material have been selected from

materials that are environmentally friendly for disposal or can normally

be recycled. Instead of throwing them away, please ensure they are recycled.

4.2 DISPOSAL OF YOUR OLD APPLIANCE.

Old appliances contain materials that can be recycled. Please contact your local waste collection

centre; scrap merchant or local Hobart office about potential recycling schemes.

6

5.0 SAFETY INSTRUCTIONS.

A FULLY TRAINED AND COMPETENT PERSON MUST ONLY USE THE AGITATORS

AND/OR MIXER.

The following instructions must be observed when using the mixer.

Note: The mixer must only be used for the purpose it was designed and inline with the supplied

operating instructions.

When maneuvering or lifting a bowl and contents with a total weight in excess of 25kg a bowl truck

must be used (refer to recommended spare parts Section 13, page 39 for bowl truck part number).

5.1 DUST HAZARD.

In order to minimise any dust hazard follow the instructions detailed below.

When mixing ingredients care must be taken to avoid the inhalation of dust particles e.g. flour.

Reference should be made to product supplier's data sheets to ensure adequate

precautions/protections are taken.

Items such as flour must be added in such a manner to avoid dust particles being dispersed into the

local atmosphere.

Carefully slit the bag whilst holding in the lower part of the bowl. When mixing dry ingredient use the

lowest speed to minimise dust emission. Use a splash cover to reduce dust emissions (refer to the

recommended spare parts Section 13, page 39 for the cover part number). Mix the ingredients in the

bowl using the lowest speed until the risk of producing any dust is eliminated. Fit suitable dust

extraction equipment.

5.2 NEVER.

• Operate the mixer or agitators if a fault develops or the mixer is unsafe.

• Wear loose clothing.

• Attempt to reach into the bowl when mixing.

• Access rotating parts.

• Fit the agitator to the mixer without a bowl in place.

• Leave the agitator on machine without the bowl being fitted.

• Use excessive force when operating which could affect the stability of the mixer.

• Operate the mixer if parts are disassembled.

• Over ride the safety switches fitted to the mixer.

• Open the guard to stop machine.

• Use the bowl lift to stop machine.

• Use the mixer in an unsafe condition.

• Clean the mixer with scouring powder or a scouring pad.

• Clean aluminium agitators in dishwashers.

• Inhale mixing ingredient dust particles.

7

5.3 ALWAYS.

• Use the mixer in a well-lit area.

• Ensure the bowl, agitator and guard are correctly fitted to the mixer.

• Disconnect the mains electricity supply before cleaning the mixer.

• Clean the mixer daily.

• Stop mixer before adding more ingredients.

• Use the stop button to stop machine.

• Clean the bowl and agitators after use.

• Clean the mixer using mild soap and water.

• Service the mixer and agitators at least twice a year depending on the frequency of use.

• Use the mixer as intended and inline with the operating instructions.

• Use the correct reduced size equipment (bowl and agitators).

6.0 USING THE MIXER.

6.1

OPERATING FOR THE FIRST TIME.

Check lubrication before use.

This mixer is shipped with oil in the transmission. Check the oil level before starting the mixer.

• Electrically isolate the mixer.

• Remove the top cover.

• Unscrew the dipstick using a 3/8” hexagon Allen key and check the oil level. The oil

level must be between the two grooves on the dipstick. Refer to Fig. 1 for the dip stick

position.

This food mixer is only for professional use by suitably trained

persons. Ensure operators have read and understood this manual

and have received adequate training. MOVING AGITATOR IN BOWL,

KEEP HANDS, CLOTHING AND UTENSILS OUT WHILE IN

OPERATION. DO NOT USE WITHOUT INTERLOCKED GUARD.

The Legacy™ mixer is equipped with SmartTimer™ controls and a power bowl lift. Other operating

parts (Fig.1, page 8) and their functions are described throughout the Operation section.

The Wire Cage Guard must be in position or the mixer will not operate.

The bowl must stay in locked position on the Bowl Support or the mixer will not operate.

If the Bowl Support is not all the way up (mix position), the mixer will not operate unless the START

button is pressed and held.

If the Bowl Support is not in the mix position and the START button is pressed and held, the mixer

will operate only in STIR speed.

8

MIXER COMPONENT IDENTIFICATION

Fig. 1.

9

6.2 CONTROLS.

STANDARD TIMER CONTROLS

Model HL800 and HL1400 (With Four Mix Speeds Plus Stir Speed)

Fig. 2.

FM34947-2

Mixer Speeds (Model HL800 and HL1400)

STIR (Slow) This speed is for incorporating ingredients at the start of each

mixing process.

SPEED 1 (Low) This speed is for heavy mixtures such as pizza dough, heavy batters

and potatoes.

SPEED 2 (Medium-low) This speed is for mixing cake batters, mashing potatoes and

developing bread dough.

SPEED 3 (Medium-high) This speed is for incorporating air into light batches, as well as

finishing whipped items.

SPEED 4 (High) This speed is for maximum and accelerated air incorporation into

light batches.

10

Programmable Recipe Timer (Optional)

FM34947-3

Fig. 3

Timer Specifications (Model HL800 and HL1400)

• Maximum number of programmable recipes: 9 recipes.

• Maximum number of steps allowed for each recipe: 6 steps.

• Maximum time allowed for each step in a recipe: 30 minutes.

For additional information on use of the programmable recipe timer, refer to pages 15 through

20.

6.3 BOWL PLACEMENT.

The bowl is heavy and must be correctly handled and lifted correctly to avoid personal injury. If the total

weight of the bowl and ingredient weights are more than 25kg a bowl truck must be used. Refer to the

recommended spare parts Section 13, page 39 for the bowl truck part number. Table 1 (page 33)

details the weights of bowls and agitators.

The bowl must be installed before the agitator is installed.

To install the bowl, fully lower the bowl support. Position the bowl so the alignment pins on the

left side of the bowl support fit in the holes in the bowl. Swing the bowl into the locked position

on bowl support.

11

6.4 AGITATOR.

To install an agitator, the bowl must be on the bowl support and fully lowered.

• To Install

1. Open the wire cage.

2. Place the agitator inside the bowl and line up the horizontal slot on the agitator with the

agitator shaft pins.

3. Slide the agitator up the agitator shaft until it stops and latches.

• To Remove

1. Open the wire cage.

2. Lower the bowl by pressing and holding the down arrow on the bowl switch.

3. Hold the agitator and pull the plunger of the agitator out (Fig. 4). Slide agitator down off the

agitator shaft.

Fig. 4

FM34947-4

6.5 HOLD-TO-RUN OPERATION.

Use extreme caution whilst operating the hold to run facility when the bowl is not in the

upper position.

The Legacy™ mixer has a hold-to-run STIR feature that allows the mixer to be operated in a

STIR mode with the bowl in the down position. This allows the agitator to be gradually engaged

with the ingredients improving the blending and reducing the dust emission. The start button

must be continuously held to operate the mixer in the STIR mode. The bowl can be raised or

lowered at the same time whilst the agitator is rotating.

12

6.6 POWER BOWL LIFT.

CAUTION: Before lowering the bowl onto a bowl truck, always unlock bowl and swing

bowl out slightly.

To raise the bowl, the bowl must be in the locked position. Push and hold the up arrow on the

bowl switch.

To lower the bowl, push and hold the down arrow on the bowl switch.

To Raise the Bowl While Mixing

To raise the bowl while the agitator is mixing the product (when required by recipe or when using the

Bowl Scraper Attachment):

1. Close the wire cage, and then select a mixing speed on the SPEED dial.

2. Select a count-down time or HOLD for continuous count-up mixing.

3. While pressing and holding the up arrow on the bowl switch, press and hold the START

button.

4. When the bowl reaches the mix position, release the START button. The mixer automatically

changes to the selected mixing speed.

6.7 PREPARE FOR MIXING.

1. Place the mixing bowl on the bowl support.

2. Pour ingredients into the bowl.

3. Swing the bowl back to the locked position.

4. Place the agitator inside the bowl, and then attach it to the agitator shaft (Fig 4, page 11).

5. Return the wire cage to front-centre position.

6. Push and hold the up arrow on the bowl switch until the bowl reaches the mix position and

stops.

7. The mixer is now ready for mixing. (See Timer Operation)

FM34947-5

Fig. 5

13

6.8 OPERATING NOTES.

• STIR is to be used for incorporating ingredients. Do not use it to develop products.

• If the mixer is stopped during a mixing operation, the timer also stops. The timer starts again

where it left off when the START button is pressed.

• The SPEED window will display the current SPEED selection.

• Turn the TIME selector clockwise to take the mixer out of the hold mode.

6.9 TIMER OPERATION.

Using the Count-Up Mode (Continuous Mixing)

1. Turn the SPEED dial to select a mix speed (the SPEED setting can be changed at any time

during the mixing operation).

NOTE: STIR is to be used for incorporating ingredients. Do not use to develop dough

products.

2. Set the timer on hold by turning the TIME selector counter clockwise until "Hold" appears

in the TIME window.

3. Press the START button to begin mixing. The timer starts counting forward from 00:00.

NOTE: If the wire cage is opened at any time, the mixing operation will stop. To resume the

mixing operation, close the wire cage and press the START button.

4. Use the STOP button to stop the mixer; the mixing time is displayed in the TIME

window.

5. Press the START button to resume mixing if needed.

NOTE: When the timer reaches 50:00 minutes, it will rollover to 00:01 and continue counting

until the STOP button is pressed.

Using the Count-Down Mode (Timed Mixing)

1. Turn the SPEED dial to select a mix speed.

a. If the count-up mode was used for the previous batch, the desired time needs to be

entered.

b. If the count-down mode was used for the previous batch, the previous time will be

displayed. If a different time is needed, turn the TIME selector to the desired time.

2. Press the START button to begin mixing; the timer starts counting down from the set

time.

a. To stop the mixer at any time, press the STOP button. To resume mixing, press the

START button. For example: The mixer is started at SPEED 1 for 30 seconds and is

stopped after 10 seconds. Pressing the START button will resume the mixing

operation.

b. If the mixer is stopped and a new time setting is entered, pressing the START button

saves the new time setting on the current speed selection. For example: The mixer is

started at SPEED 1 for 30 seconds and is stopped after 10 seconds. Turning the time

14

selector enters a new time. The new time will replace the initial 30 seconds for SPEED 1

after the START button is pressed.

c. If the time is changed while mixing, the mixer will operate until the new time expires.

The adjustment to the time will not be stored.

d. If speed is changed while mixing, the time will change to the previous time for the

selected speed and count down.

NOTE: If the wire cage is opened at any time, the mixing operation will stop. To resume the

mixing operation, close the wire cage and press the START button.

3. When the timer reaches 00:00, the mixer stops; a beeper sounds for 3 seconds. The count-

down timer displays the last-entered time.

15

Recipe Mode — To Enter and Exit

•

To enter recipe mode, press any recipe button. The recipe

button lights to indicate you are in Recipe Mode, and the

display shows the speed and time for the first step of the

recipe.

• If the recipe button light blinks, the recipe is inactive. Refer to

special functions to activate or de-activate recipe buttons.

• To exit Recipe Mode, press the lighted Recipe Button. The light

on the recipe button goes off, indicating you are in Standard

Timer Mode. The previous time setting for the shown speed will

display.

Reviewing Recipe Steps

This allows you to view a recipe without running the mixer. For

example, a three step recipe is shown.

• Select the recipe. The speed and time for the first step of the

recipe are displayed.

• Press the ENTER to display the next recipe step. Repeatedly

pressing the ENTER cycles through all the recipe steps.

• Pressing START will begin mixing step 1 of the recipe,

regardless of the step displayed.

16

Running a Recipe

• Select the desired recipe by pressing the recipe button.

The button lights and step one of the recipe displays.

• Press START.

• The mixer begins to run step one of the

programmed recipe. The timer display indicates

the mixer speed and counts down the remaining

time.

• When the time expires, the mixer automatically

switches to the speed and time for the next recipe

step and continues mixing. Mixing steps run in

succession at the programmed speed and time.

• If a Pause step is

programmed in the recipe,

the mixer stops and the time

display counts down the pause

time to 00:00 and beeps.

• After a Pause step, the speed display for the next

step flashes; press START when ready to resume

mixing.

• The mixer stops after the last step.

• The timer displays revert back to step one for that

recipe (as shown at the top of this page). Run the

same recipe again by pressing START or select a

different recipe.

• Mixing can be stopped at any time by pressing STOP.

• The speed display flashes to indicate the Program is

Interrupting a Recipe interrupted, and the timer displays the remaining time.

Press START to résumé mixing.

• If you do not wish to resume mixing, press the

recipe button twice until it is not lit — this returns

to Standard Timer Mode.

Timer will beep between steps and at end of step.

17

Entering a Special Function

Special Function Mode allows you to access three user

resettable parameters:

• Programming Recipes, (SEt . . .rECP),

• Making Recipes Active or Inactive, (Atth . . .

rECP) and

• Setting the User Access Code (SEt . . . Code).

[There are also other parameters for service use

viewable in Special Functions.] Refer to the table.

• Begin from Standard Timer Mode . . . (If you are in Recipe

Mode, exit by pressing the lighted Recipe button to return to

Standard Timer Mode.)

• With no Recipe buttons lighted, press Enter for 5

seconds. SPFn . . . turn displays indicating Special

Functions.

• There is a one minute timeout in Special Functions

Mode: After one minute of inactivity the control will

automatically return to Standard Timer Mode.

FUNCTION USED BY

SEL . . Unit Service Technician

LASt . . . Err Service Technician

Err . . . Log Service Technician

totL . . . HrS Service Technician

LASt . . . HrS Service Technician

CAP . . . HrS Service Technician

RUN . . . DiAg Service Technician

SEt . . . CodE

Authorized Operator

SEt . . . rECP

Authorized Operator

Atth . . . rECP

Authorized Operator

• Turn the Timer Dial to select one of the special functions:

SEt . . .rECP, Atth . . .rECP or SEt . . .CodE,.

Press ENTER.

Enter the Access Code

• You must enter the code to change any recipe parameters.

• CodE . . . 0000 displays.

• Turn the timer dial to the applicable access code and press

ENTER. The default access code is 0015. Refer to the

next three pages for the applicable function.

• If the incorrect code has been entered, no is displayed in

the Step Display.

18

Programming a Recipe [SEt . . . rECP]

This function allows you to program any of 9 mixer recipes with up to 6 steps in each recipe.

Follow instructions in Entering a Special Function on the previous page to enter SEt . . .rECP.

After entering the Access Code, the display of SEt . . . rECP

indicates that you can now program a recipe.

All active recipe keys are lit continuously; inactive recipe

keys blink.

• Press the recipe key you want to program (1–9). It stays

lit.

• Set the speed and mix time for step one by turning the

speed and time dials; press ENTER to go to the next

step. If the recipe was previously programmed, step 1 of

X displays to indicate the first of up to 6 steps

programmed for this recipe. The example shows that Stir

speed was previously programmed for 1 minute and 30

seconds.

• Set the speed and time for each step of the recipe, then press

ENTER to go to the next step. Repeat for each step.

• If you add more steps than were previously

programmed, the step display does not update

until the recipe has been saved. The step display

can show step 4 of 3 during programming.

• Turn timer dial counter clockwise to End to terminate

the recipe. This sets the previous step as the last step.

• Turn timer dial counter clockwise to End to terminate the

recipe. This sets the previous step as the last step.

• To save the recipe, press the lit recipe button.

• Continue programming other recipes; or press ENTER for

5 seconds to exit SEt . . . rECP and return to standard

Timer Mode.

Pro

g

rammin

g

a Pause

• If you need to stop mixing to add ingredients or to rest

the dough, you can program a Pause step. Turn the

Speed dial to the top (PAUS displays); set the timer dial

for that amount of time; press ENTER.

• The mixer cannot be restarted while the pause step is

counting down. If programming a Pause to add

ingredients, its best to set the Pause Time for a short

amount of time.

• Pause cannot be entered in first or last step of a recipe.

19

NOTE: If a recipe step is programmed wrong, exit SEt . . . rECP and re-program the entire recipe.

Making a Recipe Active or Inactive [Atth . . . rECP]

This function allows you to change the status of a recipe from Active to Inactive or vice

versa. A recipe that has inactive status will not run.

Follow instructions in Entering a Special Function on page

16 to enter Atth . . .rECP.

After entering the Access Code, the display of Atth . . .

rECP indicates that you can change the status of a recipe.

All active recipe buttons are lit continuously; inactive

recipe keys blink.

• Press any lighted recipe button to deactivate the recipe;

the recipe button blinks.

• Press any blinking recipe button to activate the recipe;

it becomes lit continuously.

• Press ENTER for 5 seconds to exit Atth . . . rECP and

return to Standard Timer Mode.

Setting the Access Code [SEt . . . CodE]

This function allows you to change the factory-set access code, 0015, to any number from

0000 to 9999. We recommend that you keep the 0015 access code.

Follow instructions in Entering a Special Function on page 16 to

enter SEt . . .CodE.

•

Turn the timer dial to the current code number and press

ENTER.

20

• The step display now reads nu..

• Turn the timer dial to the new code number and press

ENTER.

• Set…CodE displays. Press ENTER for 5 seconds to

exit Set. . .CodE and return to Standard Timer Mode.

• Make a record of the new access code.

If you lose the code, it can be restored to the factory-set default code 0015. Disconnect power to the

mixer. Press the enter key while powering up the mixer again. This resets all factory defaults.

Programmed recipes will be lost.

6.10 UNLOADING.

1. Unlock the bowl and swing-out slightly. Press and hold the down arrow on the bowl switch to

lower the bowl.

2. Open the wire cage assembly.

3. Remove the agitator from the agitator shaft.

4. Remove the bowl from the bowl support.

6.11 WIRE GUARD CAGE.

The wire cage can be rotated out of the way to add ingredients or to access the bowl and

agitator.

Note how the grooves on the nylon retainer shoes allow the Wire Cage to ride around the

circular ridge of the planetary drip cup.

• To open the wire cage, rotate it to your left.

• To close the wire cage, rotate it to your right until it stops in the front-center, closed

position.

La page charge ...

Hobart ML-134335 Mode d'emploi

Ce manuel convient également à

Hobart ML-134335 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents