Amana ACD2234HRW Manuel utilisateur

Refrigerator

Use & Care Guide

Important Safety Instructions . . . . . . . . . . . . . . . 1-2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Temperature Controls . . . . . . . . . . . . . . . . . . . . . . 8-9

Fresh Food Features . . . . . . . . . . . . . . . . . . . . . . 9-12

Freezer Features . . . . . . . . . . . . . . . . . . . . . . . . 12-13

Ice and Water . . . . . . . . . . . . . . . . . . . . . . . . . . 14-16

Water Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-19

Food Storage Tips . . . . . . . . . . . . . . . . . . . . . . . 20-22

Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . 23-26

Operating Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 28-31

Warranty & Service . . . . . . . . . . . . . . . . . . . . . . . . . 35

Guide d’utilisation et d’entretien . . . . . . . . . . . . . 36

Guía de uso y cuidado . . . . . . . . . . . . . . . . . . . . . . 70

Side by Side

1

Important Safety Instructions

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

WARNING

DANGER – Immediate hazards which WILL result

in severe personal injury or death.

DANGER

CAUTION – Hazards or unsafe practices which COULD

result in minor personal injury or property damage.

CAUTION

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

This appliance is equipped with a three-prong

grounded plug for your protection against possible

electrical shock hazards. It must be plugged into a

properly grounded wall receptacle. Where a standard

two-prong wall receptacle is encountered, it is the

personal responsibility and obligation of the customer

to have it replaced with a properly grounded three-

prong wall receptacle. Do not, under any

circumstances, cut or remove the third (ground)

prong from the power cord. Do not use an adapter

plug.

Power supply cord with

three-prong grounded plug

Properly

grounded type

wall receptacle

To reduce risk of injury or death, follow basic

precautions, including the following:

Important: Child entrapment and suffocation are

not problems of the past. Junked or abandoned

refrigerators are still dangerous – even if they sit out

for “just a few days.” If you are getting rid of your old

refrigerator, please follow the instructions below to

help prevent accidents.

Before you throw away your old

refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so

children may not easily climb

inside.

• Cut off power cord plug.

DANGER

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this Use and

Care Guide for future reference; it provides the

proper use and maintenance information.

Keep sales receipt and/or canceled check as proof

of purchase.

Call: 1-800-688-9900 USA

1-800-688-2002 Canada

Have complete model and serial number

identification of your refrigerator. This is located on a

data plate inside the fresh food compartment, on the

upper right side. Record these numbers below for

easy access.

Model Number _______________________________

Serial Number ________________________________

Date of Purchase______________________________

In our continuing effort to improve the quality and

performance of our appliances, it may be necessary

to make changes to the appliance without revising

this guide.

2

Important Safety Instructions

SAVE THESE INSTRUCTIONS

To reduce risk of fire, electric shock, serious

injury or death when using your refrigerator,

follow basic precautions, including the following:

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not

sure this appliance is properly grounded.

5. Do not ground to a gas line.

6. Do not ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate

115 volt, 15 amp., 60 cycle line.

8. Do not modify plug on power cord. If plug does

not fit wall receptacle, have proper receptacle

installed by a qualified electrician.

9. Do not use a two-prong adapter, extension cord

or power strip.

10. Do not remove warning tag from power cord.

11. Do not tamper with refrigerator controls.

12. Do not service or replace any part of refrigerator

unless specifically recommended in Use and Care

Guide or published user-repair instructions.

Do not attempt service if instructions are not

understood or if they are beyond personal skill

level.

13. Always disconnect refrigerator from electrical

supply before attempting any service. Disconnect

power cord by grasping the plug, not the cord.

14. Install refrigerator according to Installation

Instructions. All connections for water, electrical

power and grounding must comply with local

codes and be made by licensed personnel when

required.

15. Keep your refrigerator in good condition. Bumping

or dropping refrigerator can damage refrigerator

or cause refrigerator to malfunction or leak. If

damage occurs, have refrigerator checked by

qualified service technician.

16. Have worn power cords and/or loose plugs

replaced by a qualified service technician.

17. Always read and follow manufacturer’s storage

and ideal environment instructions for items being

stored in refrigerator.

18. Your refrigerator should not be operated in the

presence of explosive fumes.

19. Children should not climb, hang or stand on any

part of the refrigerator.

20. Clean up spills or water leakage associated with

water installation.

WARNING

3

Installation

To avoid severe personal injury or death,

observe the following:

• Disconnect power to refrigerator before removing

doors. Connect power only after replacing doors.

• Green ground wire must be attached to top hinge

while performing door removal and replacement.

• Tape decorative panels (select models) securely

into place before removing door handles.

WARNING

To avoid property damage, observe the following:

• Protect vinyl or other flooring with cardboard, rugs

or other protective material, prior to moving

refrigerator.

• Do not adjust refrigerator to be any shorter than

68

1

⁄2” tall (minus hinge and cap). Doing so may

damage underside components.

CAUTION

Location

• Do not install refrigerator near oven, radiator or

other heat source. If not possible, shield refrigerator

with cabinet material.

• Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (43° C). Malfunction

may occur at this temperature.

• Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, allow

1

⁄2” space at top

and

1

⁄2” space behind machine compartment cover

(located in the rear) for proper air circulation. If the

refrigerator is placed with the door hinge side against

a wall, you may want to allow additional space so the

door can be opened wider.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling, pages 4-5.

Important: If refrigerator is to be installed into a

recess where the top of the refrigerator is completely

covered, use dimensions from floor to top of hinge cap

to verify proper clearance.

Transporting Your Refrigerator

• NEVER transport refrigerator on its side. If an

upright position is not possible, lay refrigerator on its

back. Allow refrigerator to sit upright for

approximately 30 minutes before plugging it in to

assure oil returns to the compressor. Plugging

refrigerator in immediately may cause damage to

internal parts.

• Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back–NEVER from its front.

• Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not over-tighten. Over-tightening

restraints may dent or damage outside finish.

Door and Hinge Removal

Some installations require door removal to get

refrigerator to final location.

1. Unplug power cord from power source.

2. Remove toe grille (see page 4).

• Open both doors 180°, or as wide as possible.

To Disconnect the Water Line:

• Push in white collar (A) and hold.

• Pull the door-side tube (B) from the connector.

To Reconnect the Water Line:

• Firmly push tube

5

⁄8” into the connector. Use

lines on the tube as a guide for full insertion.

• If tube end is damaged, cut off

5

⁄8” before

reconnecting.

• If leaking occurs, reconnect the line.

Note: For refrigerators in operation, shut off water

before removing water line from the door.

A

B

4

Installation

6. For ice and water dispensing models only:

Detach main wire connector harness and red wire

harness.

• To detach main wire

harness, use a flat blade

tool or fingernail to press

junction point between two

connectors to release.

• To detach red wire harness,

press tab on underside of

connector to release.

7. Remove top hinges along with

doors.

8. Remove bottom hinges

with a

3

⁄8” hex head driver.

Replacing the Doors

• To replace the doors, follow the steps in Door and

Hinge Removal in reverse order.

Important: If water line tube end is damaged, cut off

5

⁄8” before reconnecting.

3. Close doors.

4. Remove top hinge covers by

removing Phillips screws.

5. Unscrew

5

⁄16” hex head screws from

top hinges.

For water dispensing

models only:

• Do not remove screw

connecting green ground

wire.

Leveling

To protect personal property and refrigerator

from damage, observe the following:

• Protect vinyl or other flooring with cardboard, rugs,

or other protective material.

• Do not use power tools when performing leveling

procedure.

CAUTION

To enhance the appearance and maintain performance,

the refrigerator should be level.

A

B

A

B

Materials Needed:

•

3

⁄8” hex head driver

• Carpenter’s level

1. Remove toe grille.

• Grasp firmly and pull bottom

outward to unclip.

2. Using hex head driver, turn front adjustment

screws (A) clockwise to raise and counterclockwise

to lower the front of the refrigerator.

Notes:

• Complete any required door reversal, panel

installation and/or a water supply connection

before leveling.

• Some models only have adjustment screws (A).

5

Installation

3. Select models also have rear adjustment screws

(B). Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

4. Using the carpenter’s level, make sure front of

refrigerator is

1

⁄4” (6 mm) or

1

⁄2 bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

5. If required, correct rocking of refrigerator by

turning rear adjustment screw clockwise to raise

rocking corner. If doors are uneven, do the

following:

• Determine which

door needs to be

raised.

• Turn front roller

adjustment screw

(A) clockwise to

raise front corner of

door.

• If one refrigerator door has reached the limit of

its adjustment range and doors are still not level,

raise or lower the opposite door by turning roller

adjustment screw clockwise or counterclockwise.

• Check with level to verify

1

⁄4” tilt to the back for

proper door closure.

• If refrigerator is aligned and stable, replace toe

grille.

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

Connecting the Water Supply

(select models)

To reduce the risk of injury or death, follow

basic precautions, including the following:

• Read all instructions before installing ice maker.

• Do not attempt installation if instructions are not

understood or if they are beyond personal skill

level.

• Observe all local codes and ordinances.

• Do not service ice maker unless specifically

recommended in Use & Care Guide or published

user-repair instructions.

• Disconnect power to refrigerator before installing

ice maker.

• Water damage due to an improper water

connection may cause mold/mildew growth. Clean

up spills or leakage immediately!

WARNING

To avoid property damage or possible injury,

follow basic precautions, including the

following:

• Consult a plumber to connect

1

⁄4” O.D. copper

tubing to household plumbing to assure

compliance with local codes and ordinances.

• Confirm water pressure to water valve is between

35 and 100 pounds per square inch, 20 pounds

per square inch without filter.

• Do not use a self-piercing, or

3

⁄16” saddle valve.

Both reduce water flow can become clogged over

time, and may cause leaks if repair is attempted.

• Tighten nuts by hand to prevent cross threading.

Finish tightening nuts with pliers and wrenches.

Do not over-tighten.

• Wait two to three hours before placing refrigerator

into final position to check and correct any water

leaks. Recheck for leaks after 24 hours.

• Verify the copper tubing under the sleeve is

smooth and free from defects. Do not reuse an

old sleeve.

CAUTION

6

Installation

Materials Needed

•

1

⁄4” outer diameter flexible copper tubing

• Shut-off valve (requires a

1

⁄4” hole to be drilled into

water supply line before valve attachment)

• Adjustable wrench (2)

•

1

⁄4” hex nut driver

Notes:

• Use copper tubing only for installation. Plastic is

less durable and can cause damage.

• Add 8’ to tubing length needed to reach water

supply for creation of service loop.

1. Create service loop with copper

tubing (minimum 2’ diameter).

Avoid kinks in the copper tubing

when bending the service loop.

Do not use plastic tubing.

2. Remove plastic cap from water valve

inlet port.

3. Place brass nut (A) and sleeve (B)

on copper tube end as illustrated.

Reminder: Do not use an old

sleeve. The nut and sleeve are

provided in the Use and Care

packet.

5. Slide brass nut over sleeve and

screw nut into inlet port.

Place adjustable wrench on nut

(1) attached to plastic waterline

and maintain position.

Using second adjustable wrench

turn the lower nut (2)

counterclockwise and fully tighten

while holding the upper nut in

place.

Important: Do not over-tighten.

Cross-threading may occur.

4. Place end of copper tubing into

water valve inlet port. Shape

tubing slightly. Do not kink – so

that tubing feeds straight into inlet

port.

6. Pull on tubing to confirm

connection is secure. Connect

tubing to frame with water tubing

clamp (C) and turn on water

supply. Check for leaks and

correct if necessary. Continue to

observe the water supply

connection for two to three hours

prior to moving the refrigerator to

its permanent location.

7. Monitor water connection for 24

hours. Correct leaks, if necessary.

Handle Installation

If not installed, the handle is located in the interior of

the fresh food section or attached to the back of your

refrigerator.

Remove and discard handle packaging and tape.

Handle design varies from refrigerator to refrigerator.

Please reference the appropriate instructions for your

model below.

Plastic Handle

Materials Needed

• Phillips screwdriver

To Install:

1. The handles are to be oriented

as shown.

2. Align door handle clip with the

door studs.

3. Ensure the large hole in the

mounting clip is positioned

down on both ends of the

handle.

4. Rotate the handle so that the

handle is flat against the door.

2’ diameter

minimum

Door

Stud

A

B

1

2

A

B

C

7

Installation

Full-Length Aluminum Handles

To Install:

1. Release top door trim by removing

Phillips screws from top of fresh food

door and retain screws for later use.

2. Align notches on back of handle with

retaining clips on doors. Insert

clips into notches and slide

handle down until it contacts

bottom trim.

3. Replace top door trim and Phillips

screws.

4. Repeat instructions 1-3 to install

other handle.

To avoid possible injury and damage to property,

tape decorative panels (select models) securely into

place before removing door handles.

WARNING

To Remove:

1. Release top door trim by removing

Phillips screws from top of fresh food

door and retain screws for later use.

2. Grasp handle firmly with both hands.

Slide handle upward approximately

3

⁄4” to release.

3. Repeat instructions 1-3 to

remove other handle.

To Reinstall:

1. Repeat in reverse order.

Handle Extensions (select models)

To Install:

1. Align and clip handle extension into position on the

handle. Press the extension over the door retainers.

To Remove:

1. Slide the extension down and unclip from door

retainer.

Door Clip

5. Grasp the handle firmly and slide

down.

To Remove:

1. Grasp the lower part of the handle firmly,

slide up, lift and remove from the

surface.

Touch Temperature Controls

(select models, style varies by model)

The controls are located at the top front of the

refrigerator compartment.

Control

Initial Control Settings

After plugging the refrigerator in, set the controls.

• Pressing the or pads adjusts the controls to

the desired setting.

• Set the Freezer control on 4.

• Set the Refrigerator control on 4.

• Let the refrigerator run at least 8 to 12 hours before

adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Temperature Controls

Dial Temperature Controls

(select models)

The controls are located at the back left of the

refrigerator compartment.

Note: The Freezer control turns the cooling system

on. Neither section will cool if freezer control is set

to OFF.

Initial Control Settings

After plugging the refrigerator in,

set the controls.

• To adjust the controls, turn the

control knob to the left or right

as desired.

• Set the Freezer control on 4.

• Set the Refrigerator control

on 4.

• Let the refrigerator run at least 8

to 12 hours before adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

• 24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table above right. See

page 20 for instructions on checking compartment

temperature.

• Except when starting the refrigerator, do not change

either control more than one number at a time.

• Allow 24 hours for temperatures to stabilize.

• Changing either control will have some effect on the

temperature of the other compartment.

Temperature Control Guide

Refrigerator too warm

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn refrigerator OFF

Turn the Refrigerator control

to next higher number.

Turn the Refrigerator

control to next lower number.

Turn the Freezer control to

next higher number.

Turn the Freezer control to

next lower number.

Turn the Freezer control to

OFF.

Note: Turning freezer control to OFF stops cooling

in both compartments. It does not shut off power to

the refrigerator.

8

Temperature Control Guide

Refrigerator too warm

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn refrigerator OFF

Set the Refrigerator control

to next higher number by

pressing the pad.

Set the Refrigerator control

to next lower number by

pressing the pad.

Set the Freezer control to

next higher number by

pressing the pad.

Set the Freezer control to

next lower number by

pressing the pad.

Press the Freezer or

Refrigerator pad until

a dash “–” appears in the

display.

9

Temperature Controls

Adjusting the Controls

• 24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table at right. See

page 20 for instructions on checking compartment

temperature.

• Except when starting the refrigerator, do not change

either control more than one number at a time.

• Allow 24 hours for temperatures to stabilize.

• Changing either control will have some effect on the

temperature of the other compartment.

Fresh Food Features

Shelves

To avoid personal injury or property damage,

observe the following:

• Never attempt to adjust a shelf that is loaded with

food.

• Confirm shelf is secure before placing items on

shelf.

• Handle tempered glass shelves carefully. Shelves

may break suddenly if nicked, scratched, or

exposed to sudden temperature change.

CAUTION

Your refrigerator has either Spillsaver™ or non-sealed

shelves. Spillsaver™ shelves have a spill retainer edge

which allows for easier clean up and some are

equipped with the EasyGlide™ slide out feature. To

slide out (select models), grasp the front of the shelf

and pull forward. Push in the shelf to return to the

original position.

To Remove a Shelf:

• Slightly tilt up the

front and lift up the

rear of the shelf, then

pull the shelf straight

out.

To Lock the Shelf Into Another Position:

• Tilt up the front edge of the shelf.

• Insert the hooks into the desired frame openings and

let the shelf settle into place.

• Be sure the shelf is securely locked at the rear.

The Crisper Top serves as the lower fresh food shelf.

To Remove the Crisper Top:

• Remove drawers as indicated (see page 11).

• Place hand under the frame to push up the glass. Lift

glass out.

• To install, repeat above instructions in reverse order.

SideGlide™ Shelves (select models)

SideGlide™ Shelves can be

adjusted to create a full-

width shelf, or to slide from

side to side to accommodate

storage needs.

To Remove Shelf Rail

Assembly:

• Lift rail assembly up to remove hooks from frame.

Dairy Center

The Dairy Center provides convenient

door storage for spreadable items

such as butter and margarine. This

compartment can be moved to

several different locations to

accommodate storage needs.

To Remove:

• Slide dairy center up and pull out.

To Install:

• Slide assembly in and down so that the hooks are

firmly seated on the door liner.

To Remove Dairy Door:

• Press in sides of dairy door and pull out.

To Install Dairy Door:

• Slide sides of dairy door inside dairy center until

hinge points snap into place.

Adjustable Deep Tilt-Out Door Bucket

(select models)

The Adjustable Deep Tilt-Out Door Bucket provides

easy access to food items stored in the door.

To Remove Bucket:

• Tilt bucket out.

• Pull straight out of the bracket.

Door Storage

Beverage Chiller™/MiniChiller™

(select models)

The Beverage Chiller™ and

MiniChiller™ keep beverages and

other items colder than the rest of

the fresh food compartment. An air

inlet directs air from the freezer into

the chiller(s).

Controls

The chiller control is located on the left

side wall of the fresh food compartment.

Turn the control clockwise for colder

temperature.

To Remove Chiller(s):

• Unload the chiller(s).

• Slide the assembly up and pull straight out.

Note: If the chiller is installed directly under the

dairy center or a door bucket, the bucket or dairy

center will need to be removed before removing the

chiller.

Note: The chillers will not operate properly if the

air intake hole is not aligned with the control

location.

To Install Chiller(s)

• Align one of the air inlet holes with the hole cut-out

on the door.

• Slide the assembly in and down so that the hooks

are firmly seated on the door liner.

10

Fresh Food Features

To Install Shelf Rail Assembly:

• Tilt up the front edge of the assembly.

• Insert the hooks into the desired frame openings and

let the rail assembly settle into place.

• Be sure the rail assembly is securely locked into the

frame.

To Install SideGlide™ Shelves for Full-Width:

• Tilt up the front edge of the shelf slightly.

• Hook the rear lip of the shelf over one of the rails on

the shelf rail assembly.

• Let the shelf settle into place.

• Install the other SideGlide™ shelf on the same rail of

the shelf assembly.

To Install SideGlide™ Shelves for

Sliding Side to Side:

• Tilt up the front edge of the shelf slightly.

• Hook the rear lip of the shelf over one of the rails on

the shelf rail assembly.

• Let the shelf settle into place.

• Install the other SideGlide™ shelf on the other rail of

the shelf rail assembly.

11

Fresh Food Features

To Install Bucket:

• Tilt the front of the bucket down slightly.

• Slide into bracket and tip upright.

To Move Bucket Frame to Another Location:

• Remove bucket.

• Lift bracket up and pull straight

out.

• Place the bracket in a new location.

Door Buckets

Door Buckets can be moved to meet individual storage

needs.

To Remove:

• Lift bucket up and pull straight out.

To Install:

• Place bucket in desired door liner

retainer, push down until bucket

stops.

Can Pack Keeper (select models)

The Can Pack Keeper conveniently dispenses up to a

12 pack of individual beverage cans. To load

beverages into the Can Pak Keeper:

• Open a 12 pack sleeve of

beverages.

• Slide Can Pak Keeper over the

cutout portion of beverage

sleeve

• Place container and sleeve in an

upright position in a door bucket

located in the fresh food door

compartment.

The dispenser sits in the door

bucket and can be moved to

accommodate a variety of storage

needs.

Storage Drawers

Humidity-Controlled Crisper Drawers

The Crisper Drawers provide a higher humidity

environment for fresh fruit and vegetable storage.

Controls

The crisper controls regulate the amount of humidity in

the crisper drawer. Slide control toward the Fruit

setting for produce with outer skins. Slide control

toward the Vegetables setting for leafy produce.

Note: For best results, keep the crisper drawers

tightly closed.

To Remove:

• Pull drawer out to full extension. Tilt up front of

drawer and pull straight out.

To Install:

• Insert drawer into frame rails and push back into

place.

Temperature-Controlled Drawer

(select models)

This drawer can be used for

storage of miscellaneous items.

The drawer features a control

that regulates the air

temperature in the drawer. Set

the control to Cheese to provide

normal refrigerator temperature.

Use the Meats setting for meats.

Beverage Organizer™ (select models)

The Beverage Organizer™ slides

out from underneath the

Spillsaver™ stationary shelf. The

Beverage Organizer™ holds up to

twelve 12-ounce beverage cans.

12

Fresh Food Features

To Remove:

• Empty contents of can rack. Pull Beverage Organizer™

forward to full extension and lift front to release from

shelf rail assembly. Pull straight out to remove.

To Install:

• Insert rack into frame rails and push back into place.

Accessories

Grip Pads (select models)

The Grip Pads prevent objects from

sliding in the door buckets. Grip Pads are

removable and are top-rack dishwasher safe for easy

cleaning.

Covered Storage Bucket

(select models)

The Storage Bucket has a lid and

removable egg tray. When tray is

removed, bucket will accept items such

as a standard egg carton, ice, etc.

Tall Bottle Retainer/Snugger

(select models)

The Tall Bottle Retainer

prevents tall bottles from

tipping forward. The Retainer

can be placed above any

removable door bucket.

The Snugger attached to the Tall Bottle Retainer keeps

bottles and other containers in place when the door is

opened or closed. Adjust the Snugger by sliding from

side to side.

Egg Tray With Handle

(style may vary/select models)

The Egg Tray with Handle holds a

“dozen-plus” eggs. It can be

removed to carry to a work area

or to be washed.

Freezer Features

Shelves and Baskets

Fixed Freezer Shelf

To Remove Clip-Mounted

Shelves:

• Lift shelf from wall mounting

clips and pull left side of shelf

out of wall mounting holes.

To Install Clip-Mounted Shelves:

• Place left side of shelf in mounting holes and press

down into wall mounting clips.

Shelves

Shelves can be removed to meet

individual storage needs.

To Remove Shelf:

• Snap right side of shelf up from cabinet railing and

slide to right.

To Install Shelf:

• Replace shelf in left side cabinet railing. Snap shelf

into right side cabinet railing.

Baskets and Drawers

Baskets and drawers (style may vary) slide

out for easy access of items in back.

To Remove:

• Pull out to its full extension. Lift

up front of basket or drawer and

remove.

To Install:

• Slide basket or drawer into cabinet railing. Lift up

front of basket or drawer, and slide to the back of

refrigerator.

Freezer Features

Door Storage

Adjustable Door Buckets

Door Buckets can be moved to meet individual storage

needs.

To Remove:

• Lift the door bucket up until it

clears the retainers on the door

liner, then pull the door bucket

straight out.

Tilt-Out Door Buckets (select models)

The Tilt-Out Door Bucket provides easy access to food

items stored in the door.

To Remove Bucket:

• Tilt bucket out.

• Pull straight out of the frame.

To Install Bucket:

• Tilt the front of the bucket down slightly.

• Slide into frame and tip upright.

To Move Bucket Frame to Another Location:

• Remove bucket.

• Lift frame up and pull straight

out.

Slide the frame in and down into the new location.

Ice Storage Bin

The Ice Storage Bin is located below the automatic ice

maker.

To Remove:

• Raise ice maker arm to deactivate ice maker. Lift

front of bin and pull out to its full extension. Lift up

front of bin and remove.

To Install:

• Slide bin into railing below ice maker until bin locks

into place. Drop ice maker arm to activate ice maker.

Important: Ice bin must be locked in place for proper

ice dispensing. Turn auger driver behind bin

counterclockwise (as shown) to properly align ice bin

with auger driver.

13

To Install:

• Slide bucket in above desired door liner retainer and

push down until bucket stops.

Fixed Door Bucket (select models)

The Fixed Door Bucket is located in the

upper section of the freezer door.

Important: Fixed door bucket is NOT

adjustable. If bucket is removed, freezer

light will not deactivate when door is

closed.

Ice and Water

Automatic Ice Maker

(non-dispenser models)

Note: Energy rating guides that are posted on the

refrigerator at the time of purchase do not include

optional ice maker energy usage.

To avoid personal injury or property damage,

observe the following:

• Do not place fingers or hands on the automatic

ice making mechanism while the refrigerator is

plugged in. This will help protect you from possible

injury. It will also prevent interference with moving

parts of the ejector mechanism and the heating

element that releases the cubes.

• Under certain rare circumstances, ice cubes may

be discolored, usually appearing with a green-

bluish hue. The cause of this unusual discoloration

can be a combination of factors such as certain

characteristics of local waters, household

plumbing and the accumulation of copper salts in

an inactive water supply line which feeds the ice

maker. Continued consumption of such discolored

ice cubes may be injurious to health. If such

discoloration is observed, discard the ice cubes

and contact your dealer to purchase and install a

water line filter.

• Water damage due to improper water connection

may cause mold/mildew growth.

• Clean up water and ice spills to avoid personal

injury and to prevent mold/mildew growth.

WARNING

Some models are automatic ice maker ready. The

number of the appropriate ice maker kit is IC10S. The

kit contains installation instructions and water

connection instructions.

Other models have a factory installed ice maker.

Connect the ice maker to the water supply as

instructed on pages 5 and 6. Proper water flow and

a level refrigerator are essential for optimal ice

maker performance.

Operating Instructions

• Confirm ice bin is in place and ice maker arm is

down.

• After freezer section reaches

approximately 0° to 2° F (-18° to

-17° C), ice maker fills with water

and begins operating. You will have

a complete harvest of ice

approximately every three hours.

• Allow approximately 24 hours after installation to

receive first harvest of ice.

• Discard ice created within first 12 hours of operation

to verify system is flushed of impurities.

• Stop ice production by raising ice maker arm until

click is heard.

• Ice maker will remain in the OFF position until arm is

pushed down.

• The first one or two batches will probably contain

undersized and irregular cubes because of air in the

supply line.

• When the ice cubes are ejected it is normal for

several cubes to be joined together at the ends. They

can easily be broken apart. The ice maker will

continue to make ice until the supply of ice cubes

raises the sensor arm, shutting the ice maker off.

• Certain sounds may accompany the various cycles of

the ice maker. The motor may have a slight hum, the

cubes will rattle as they fall into an empty storage

pan and the water valve may click or “buzz”

occasionally.

• If the ice is not used frequently, the ice cubes will

become cloudy, shrink, stick together and taste stale.

Empty the ice storage bin periodically and wash it in

lukewarm water. Be sure to dry the bin thoroughly

before replacing it.

• Beverages and foods should not be placed in the

ice storage bin for quick chilling. These items can

block the sensor arm, causing the ice maker to

malfunction.

• Turn OFF (arm up) the ice maker when the water

supply is to be shut off for several hours.

To Remove the Ice Bin:

• Pull it forward, away from the ice maker. To avoid the

ice maker dumping ice while the bin is removed, turn

the ice maker OFF by raising the sensor arm.

To Install the Ice Bin:

• Reverse the above procedure. Turn the ice maker ON

by lowering the sensor arm.

14

15

Dispenser Light (select models)

A light activates within the dispenser area at full power

when dispensing ice or water with the main dispenser

pad. The light will also illuminate when using the

FrontFill™ Button (select models).

Dispenser Pad

The Dispenser Pad is located on the back wall of the

dispensing area. When the dispenser pad is pressed,

the selection chosen on the dispenser control panel

will dispense.

FrontFill™ Button (select models)

The FrontFill™ Button works independently of the

dispenser controls, providing an up-front alternative to

the dispenser pad for dispensing water. This feature is

convenient for filling large items that will not fit into

the dispenser area (i.e. sport bottles, pitchers, large

pans, coffee pots).

This feature allows added convenience of dispensing

ice and water simultaneously. To use, choose your

preferred ice mode from dispenser control panel. Press

container against dispenser pad while pressing the

Front Fill

TM

Button.

Removable Tray

The Removable Tray at the bottom of the dispenser

area is designed to collect small spills and may be

easily removed for cleaning and emptying purposes.

Important: Removable tray does not drain. Do not

allow tray to overflow. If it does, remove tray and wipe

up overflow.

Water Dispenser Operation

To avoid personal injury or property damage,

observe the following:

• Do not put fingers, hands or any foreign object

into dispenser opening.

• Do not use sharp objects to break ice.

• Do not dispense ice directly into thin glass, fine

china or delicate crystal.

CAUTION

To Use Dispenser Pad:

• Choose water selection from dispenser control panel.

• Press sturdy, wide-mouthed container against

dispenser pad. When dispensing crushed ice, hold

container as close to chute as possible to reduce

spraying.

• Release pressure on dispenser pad to stop water

dispensing. A small amount of water may continue to

dispense and collect in dispenser tray. Large spills

should be wiped dry.

Note: During initial use of water dispenser, there

will be a one- to two-minute delay while water tank

fills before water dispenses. Discard first 10-14

glasses of water after initially connecting refrigerator

to household water supply and after extended

periods of nonuse.

Ice and Water

FrontFill™

Button

Dispenser Features

(select models)

Main

Dispenser

Pad

Removable

Tray

16

Dispenser Lock (select models)

The Dispenser Lock prevents ice or water

from being dispensed.

To Lock Dispenser:

• Press and hold the Lock button for three seconds. A

green indicator light above button will illuminate

when the dispenser is locked.

To Unlock Dispenser:

• Hold the Lock button for three seconds. The green

indicator light above button will go out.

Water Filter Status Indicator

Light

(select models)

The Water Filter Status Indicator Light serves as a

reminder to replace the water filter. A green light

indicates that the filter is in good condition. A red light

indicates the filter should be changed. Once light turns

red, it will remain red until function is reset.

To Reset Indicator:

• Press and hold both the Lock and Water

buttons simultaneously for four seconds.

The green filter status indicator light will

flash three times when the function has

successfully reset.

Ice and Water

Dispenser Control (select models)

(control features vary by model)

Ice Dispenser Operation

To Dispense Ice:

• Select Crushed or Cubes ice mode by

pushing button on dispenser control

panel. A green light above button

indicates mode selection.

• Press container against dispenser pad.

When dispensing crushed ice, hold

container as close to chute as possible to reduce

spraying.

Auto Light (select models)

The Auto Light function activates the

dispenser light at half-power when the Light

Sensor detects that the light levels in room are low.

To Activate Auto Light:

• Press Auto Light button. A green indicator light

above button illuminates when the sensor is active.

To Deactivate Auto Light:

• Press Auto Light button. The green indicator light

will go out.

Notes:

• Mode may not be changed while ice dispenser is

in operation.

• If dispenser (select models) is active for more than

five minutes, an automatic lock out sensor will

shut down power to dispenser area. See Dispenser

Lock for unlocking information.

Note: The dispenser light will operate when Auto

Light is ON or OFF.

Sabbath Mode (select models)

When activated, the Sabbath Mode deactivates the

control lights while leaving the control operational.

To Activate Sabbath Mode:

• Press and hold the Lock and Auto Light

buttons simultaneously for three to four

seconds. After three to four seconds, the

dispenser lights will turn off.

To Deactivate Sabbath Mode:

• Press and hold both the Lock and Auto Light

buttons simultaneously for three to four seconds.

After three to four seconds, the dispenser lights will

activate.

Notes:

• Dispenser light will not activate during dispensing

while in this mode.

• If the power fails, the control will remain in

Sabbath Mode when power returns.

17

Water Filter

Water Filter Removal and

Installation

(select models)

To avoid serious illness or death, do not use

refrigerator where water is unsafe or of unknown

quality without adequate disinfection before or after

use of filter.

WARNING

After installing a new water filter, always

dispense water for two minutes before

removing the filter for any reason. Air trapped in

system may cause water and cartridge to eject.

Use caution when removing.

• The bypass cap does not filter water. Be sure to

have replacement cartridge available when filter

change is required.

• If water filtration system has been allowed to

freeze, replace filter cartridge.

• If system has not been used for several months, or

water has an unpleasant taste or odor, flush

system by dispensing water for two to three

minutes. If unpleasant taste or odor persists,

change filter cartridge.

CAUTION

Initial Installation

The water filter is located in the upper right hand

corner of the fresh food compartment.

1. Remove blue bypass cap and

retain for later use.

2. Remove sealing label from

end of filter and insert into

filter head.

3. Rotate gently clockwise until

filter stops. Snap filter cover

closed.

4. Reduce water spurts by

flushing air from system.

Run water continuously for

two minutes through

dispenser until water runs

steady. During initial use,

allow about a one- to two-minute delay in water

dispersal to allow internal water tank to fill.

• Additional flushing may be required in some

households where water is of poor quality.

Replacing Water Filter

Important: Air trapped in system may cause

water and cartridge to eject. Use caution when

removing.

1. Turn filter counterclockwise until it releases from

filter head.

2. Drain water from filter into sink, and dispose in

normal household trash.

3. Wipe up excess water in filter cover and continue

with Initial Installation, steps 2 and 4.

The filter should be changed at least every 12 months.

Important: Condition of water and amount used

determines life span of water filter cartridge. If water

use is high, or if water is of poor quality, replacement

may need to take place more often.

To purchase a replacement water filter cartridge,

contact your dealer or call 1-877-232-6771 USA or

1-800-688-8408 Canada.

The dispenser feature may be used without a water

filter cartridge. If you choose this option, replace filter

with blue bypass cap.

18

Water Filter

System Specification and Performance Data Sheet

Refrigerator Water Filter Cartridge Model UKF8001AXX

Specifications

Service Flow Rate (Maximum).............................................0.78 GPM (2.9 L/min)

Rated Service Life UKF8001AXX-750 (Maximum)......750 gallons/2838 liters

Maximum Operating Temperature .....................................100° F / 38° C

Minimum Pressure Requirement........................................35 psi /241 kPA

Minimum Operating Temperature......................................33° F/1° C

Maximum Operating Pressure.............................................100 psi /689 kPA

Performance Data

1000 Apollo Road

Eagan, Minnesota 55121-2240

651.450.4913

EPA EST #35917-MN-1

100834/B

The PuriClean

®

II retractable water filtration system uses a

UKF8001AXX replacement cartridge. Timely replacement of

filter cartridge is essential for performance satisfaction from

this filtration system. Please refer to the applicable section of

your Use & Care Guide for general operation, maintenance

requirements and troubleshooting. Suggested retail price of

replacement water filter is $39.99.

This system has been tested according to ANSI/NSF 42 and

53 for reduction of the substance listed above. T

he

concentration of the indicated substances in water entering

the system was reduced to a concentration less than or equal

to the permissible limit for water leaving the system, as

specified in ANSI/NSF 42 and 53.

* Tested using a flow rate of 0.78 gpm; pressure of 60 psig; pH of 7.5 + 0.5; temp. of

68° + 5° F (20° + 3° C)

** Measurement in Particles /ml. Particles used were 0.5 - 1 microns

*** NTU - Nephelometric Turbidity Units

General Use Conditions

Read this Performance Data Sheet and compare the

capabilities of this unit with your actual water treatment

needs.

DO NOT use this product where water is microbiologic-

ally unsafe or of unknown quality without adequate

disinfection before or after the system. System certified

for cyst reduction may be used on disinfected water

that may contain filterable cysts.

US

E ONLY WITH COLD WATER SUPPLY. CHECK FOR

COMPLIANCE WITH THE STATE AND LOCAL LAWS

AND REGULATIONS.

TM

Standard No. 42: Aesthetic Effects

Taste and Odor Reduction

Chlorine Taste & Odor

Mechanical Filtration Unit

Particulate Reduction Class 1

Standard No. 53: Health Effects

Chemical Reduction Unit

Lead, Atrazine, Lindane, Benzene,

Carbofuran, p-Dichlorobenzene, Mercury

& Toxaphene Reduction

Mechanical Filtration Unit

Cyst, Turbidity and Asbestos Reduction

Tested and certified by NSF International against ANSI/NSF Standards 42 & 53

in models UKF8001AXX-750 for the reduction of:

Parameter

Chlorine

T & O

Particulate**

USEPA

MCL

—

Standard No. 42: Aesthetic Effects

Influent

Challenge Concentration

2.0 mg/L ± 10%

—

at least 10,000 particles/ml

Influent

Average

1.88 mg/L

—

5,700,000 #/ml

Average

<0.05136364 mg/L

—

30,583 #/ml

Maximum

0.06 mg/L

—

69,000 #/ml

Average

>97.26%

—

99.52%

Minimum

96.84%

—

98.94%

Min. Required

Reduction

50%

—

85%

Effluent % Reduction

Parameter

Turbidity

Cysts

Asbestos

Lead at pH 6.5

Lead at pH 8.5

Mercury at pH 6.5

Mercury at pH 8.5

Atrazine

Benzene

Carbofuran

p-Dichlorobenzene

Lindane

Toxaphene

USEPA

MCL

1 NTU**

99.5% Reduction

99% Reduction

0.015 mg/L

0.002 mg/L

0.003 mg/L

0.005 mg/L

0.04 mg/L

0.075 mg/L

0.0002 mg/L

0.003 mg/L

Standard No. 53: Health Effects

Influent

Challenge Concentration

11 ± 1 NTU***

Minimum 50,000/L

10

7

10

8

fibers/L; fibers >10 micrometers in length

0.15 mg/L + 10%

.006 mg/L ± 10%

0.009 mg/L + 10%

0.015 mg/L ± 10%

0.08 mg/L ± 10%

.225 mg/L ± 10%

0.002 mg/L + 10%

0.015 ± 10%

Influent

Average

10.7 NTU

166,500 #/L

155 MF/L

0.153 mg/L

0.150 mg/L

0.006 mg/L

0.009 mg/L

0.014 mg/L

0.081 mg/L

0.208 mg/L

0.002 mg/L

0.015 mg/L

Average

0.31 NTU

<1 #/L

<1 MF/L

<.001 mg/L

0.0003 mg/L

0.0008 mg/L

<0.002 mg/L

0.0006 mg/L

<0.001 mg/L

<0.0005 mg/L

0.000 mg/L

<0.001 mg/L

Maximum

.049 NTU

<1 #/L

<1 MF/L

<.001 mg/L

0.0005 mg/L

0.0015 mg/L

0.002 mg/L

0.0011 mg/L

<0.001 mg/L

<0.0005 mg/L

<0.0001 mg/L

<0.001 mg/L

Average

97.09%

>99.99%

>99.35%

>99.33%

95.70%

86.22%

76.99%

95.71%

98.74%

99.76%

98.72%

92.97%

Minimum

95.20%

>99.99%

>99.29%

90.91%

75.93%

75.31%

92.14%

98.46%

99.74%

96.50%

91.67%

Min. Required

Reduction

0.5 NTU

>99.95%

99%

0.10 mg/L

0.002 mg/L

0.003 mg/L

0.005 mg/L

0.04 mg/L

0.075 mg/L

0.0002 mg/L

0.003 mg/L

Effluent % Reduction

19

Water Filter

State of California

Department of Health Services

Water Treatment Device

Certificate Number

03 - 1583

Date Issued: September 16, 2003

Date Revised: April 22, 2004

Trademark /Model Designation Replacement Elements

UKF8001AXX750 UKF8001AXX

469006-750 46 9006

67003523-750 67003523

Manufacturer: PentaPure Inc.

The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the

Health and Safety Code for the following health related contaminants:

Microbiological Contaminants and Turbidity Inorganic/Radiological Contaminants

Cysts Asbestos

Turbidity Lead

Mercury

Or

ganic Contaminants

Atrazine

Lindane

Benzene

Carbofuran

p-dichlorobenzene

Toxaphene

Rated Service Capacity: 750 gal. Rated Service Flow: 0.78 gpm

Conditions of Certification:

Do not use wher

e water is microbiologically unsafe or with water of unknown quality, except that systems certified for cyst

reduction may be used on disinfected waters that may contain filterable cysts.

La page charge ...

Amana ACD2234HRW Manuel utilisateur

Amana ACD2234HRW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents